NIDEC MOBILITY CGF-M002 EV Remote Antenna Module User Manual EV Remote Operation manual ai

OMRON Automotive Electronics Co. Ltd. EV Remote Antenna Module EV Remote Operation manual ai

Users Manual

EV_REMOTE operation manual Antenna module34Regulatory complianceConfigurationPart namesStickLCDPower / Link buttonMode setting buttonManual  charge buttonSetting button (UP)Product labelBattery coverProduct labelCN2 connectorCN1 connector (antenna connection)Battery replacementBatteries: CR2032 x 2    We recommend that you replace the batteries after one year's use as a guide.  How to replace the batteries1. Remove the battery cover Slide the slide part of the battery cover inthe direction of     and lift the cover in the direction of     to release the hooks of thebattery cover (   ).Battery coverSlide partlithium batteries(CR2032)Insert the new batteries (CR2032) with the positive ( + ) side facing up. 2. Replace the batteries  3. Place the battery cover   After inserting the hooks of the battery cover (   ), lower the cover into position (   ) and slide the slide part in the direction of    . Main specificationsAfter sales serviceHow to useFor after sales service, contact : OMRON Automotive Electronics Co. Ltd.6368 nenjyozaka, okusaKomaki, Aichi 485-0802  JAPANTel: +81 568 78 6392URL: http://www.oae.omron.co.jpStickAntenna moduleTransmission frequency              926.85 MHz band (FCC/IC), 869.85 MHz band (EU)  Transmission power                    < 50 mV/m (FCC/IC),  <  5mW e.r.p (EU)  Antenna                                      1/4 lambda rod antenna           Switches                                     Power on/off, Mode, Charge, Setting Battery                                        Lithium battery (CR2032 x 2) Dimensions                                88.4 mm x 32 mm x 18 mm ( not including protrusion)Weight                                        35 g                     Link state acknowledgment        Buzzer / LCD      Transmission frequency             926.85 MHz band (FCC/IC), 869.85 MHz band (EU)  Transmission power                  < 50 mV/m (FCC/IC),  <  5mW e.r.p (EU)  Power supply                             5 V                    Current consumption                  1.5 mA (for receiving)                              Antenna                                     1/4 lambda printed antenna                                        Operation temperature range     -10 C to +70 C Operation temperature range     -30 C to +85 C Dimensions                                 52 mm x 25 mm x 52 mm Weight                                         35 g                     Turning the power of the stick onSetting the charge timeSetting the air conditioner Turning the power of the stick offPressing the Power/Link button for more than 1 second turns the power of the stickon (with a buzzer sound) and the stick starts transmitting a request signal to obtain vehicle information. If a response signal from the vehicle is properly received, the vehicle information will be displayed on the LCD with a buzzer sound.The time till charging is started (charge wait time) and the charging time can be set with the stick.Caution When pulling the antenan out or putting it back, move it straight up/down with holding the top of the antenna. The antenna may be damaged if being pulled  with brute force or bended. Pressing the mode setting button once while the vehicle informaiotn is displayed onthe LCD enables the charge wait time setting mode. In the charge wait time setting mode, the charge wait time can be set with the setting button. After setting the wait time, the setting information will be sent to the vehicle by pressing the Power/Link button. If a response signal from the vehicle is properly received, the setting information will be displayed on the LCD with a buzzersound. By pressing the mode setting button once during the charge wait time setting mode,  the stick is set to the charge time setting mode. Set the charge time in the same wayas done for setting the charge wait time. Pressing the manual charge button resets the timer setting. The car air conditioner can be controlled with the stick prior to getting into a car.Pressing the mode setting button once in the charge time setting mode enables the air conditioner setting mode.    Select the temperature you want with the setting button and press the Power/Link button to send the setting information to the vehicle.   If a response signal from the vehicle is properly received, the setting information will bedisplayed on the LCD with a buzzer sound. Pressing the Power/Link button for more than 3 seconds while the power is on turns the power of the stick off. Also no button operation for more than 30 seconds automatically turn the power off.Setting button (DOWN)FCC/IC WARNINGAny changes or modifications not expressly approved by the party responsible for product compliance could void the user's authority to operate the equipment.  This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC The following standards were applied: (R&TTE Directive 1999/5/EEC)  EN 60950-1: 2006 + A11:2009 EN 300 220-2 V.2.3.1 EN 301 489-3 V.1.4.1 EN 62311:2008 Hereby, OMRON Automotive Electronics Co. Ltd., declares that Stick / Antenna module are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.50 g

Navigation menu