NINGBO DOOYA MECHANIC and ELECTRONIC TECHNOLOGY DC1673 Emitter User Manual eDC1672DC1673 A 01

NINGBO DOOYA MECHANIC & ELECTRONIC TECHNOLOGY CO., LTD. Emitter eDC1672DC1673 A 01

User Manual

Emitter SpecificationType specificationTechnical supportVersion NO. : A/02Fucntion instructionTechnical specificationInput voltage碋3V(CR2430)Transmitting frequency碋433MHzTransmitting power碋10 milliwattOperating temperature碋-50C—500CTransmssion distance碋200 meters open office硽 35 meters on two wallsTransmitter: five channels (DC1672), fifteen channels (DC1673). One number of LCD screen means one control channel. Press “channel choose” button P1- (number descending) or P1+ (number increasing) to change the channel. On the analogy of this, loose finger when the indicator light move to suitable channel that you select effective channel. If LCD screen number show “0” that means all channels if effective (group control state).Notice: transmitter do not exposed to moisture and strike, so as not to affect life.When you use transmitter, if found emission distance obviously short or less sensitive, please change another same new battery. Please have batteries for recycling.DC1672 DC1673AAdditionalfunctionMatchable R tubular motor set upDuring the settings, the time between two operation must be shorter than 4s, otherwise it will quit the settingDuring the settings, the time between two operation must be shorter than 6s, otherwise it will quit the settingDuring the settings, the time between two operation must be shorter than 10s, otherwise it will quit the settingAAdditionalfunctionMatchable DC1680 / DC1681 set upAAdditionalfunctionMatchable DC136 set upPower onSettingis okOKP2×1See indicatorflashingSee green in-dicator flashing and extinguishedSee indicator long flashingEmitterReceiverReceiverStop button×1 Up button×1Up button ×1Down button ×1OKOKPower onHear long sound Hear di di...Setting is ok.The up button controlthe motor clockwiseSetting is ok.The down button controlthe motor clockwiseSound tip three times Sound tip three times Power on EmitterReceiverReceiverSee indicatorflashingSettingis okOKSee indicatorflashingSee indicator long flashing(Up button +Down button)×2s Stop button×1 Up button×1Up buttonStop buttonDown buttonLCD screenDC167315 - channel LCD emitterP1- buttonP1+ buttonUp buttonStop buttonDown buttonLCD screenDC16725 - channel LCD emitterP1- buttonP1+ buttonTTechnical supportTTechnical supportAfter matching code for new emitter, it will clear all the data in the motorReservedbuttonReservedbuttonSetting button=P1+ button +Reserved button(P1+button +Reserved button)×2Settingis okStop×1(P1+button+P1-button)×1P1+button+P1-button,hold onAAdditionalfunctionThe valid channels selectionIn the setting state,press the up or down button you can quit quickly, if you want to change the valid channels ,reset it.The screen will display oPress P1+button or P1-button, selecting the channel (channe l1 to channel 15) you needOKThe screen will display 15The screen will display C Or
FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ǂ Reorient or relocate the receiving antenna. ǂ Increase the separation between the equipment and receiver. ǂ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ǂ Consult the dealer or an experienced radio/TV technician for help.

Navigation menu