NINGBO DOOYA MECHANIC and ELECTRONIC TECHNOLOGY DD5712 Motor Remote Control User Manual DM35LE S

NINGBO DOOYA MECHANIC & ELECTRONIC TECHNOLOGY CO., LTD. Motor Remote Control DM35LE S

Contents

User manual

Tubular Motor-DM18LE/SSpecification（A-OO）Rated Voltage(V)Rated Torque(N.m)Functional features：Jogging&tilt functionSet electronic limitSet /delete the third limit positionLow standby power Integrated radio controlSetting up+add emitter+delete emitterMotor direction setting optionResistance stop function-1085Emission frequency(MHz)Rated speed(RPM)1. Please charge the battery and make sure it is fully charged before the first use2. Don’t operate motors wheuin low wltage alarm: ①Motor stop running When the supply voltage is lower than 7 v， and it will restart again when the voltage is greater than 7.5V ②If the voltage is less than 10v, the motor will alarm for 10 times to prompt it needs to be charged every timewhen the motor is working.3. Optrating： ①The valid interval of the emitter button is 10s,the emitter will quit the set after 10s ②The motor will run or beep for hint,please do the next step after the hint.4. Set limit position： ①After the up limit and down limit setting,and the up limit down limit and third limit position are at the same location ②After limit setting，with power and memory function; ③Into the match-code status 2 minutes later, it will quit out the setting limits status automatically ④It will delete every memory and restore the factory settings5. When the motor running without any operation, the maximum running time is 6 minutes,it will stop automatically6. If the emitterlost,please set up again with new emitter&The motor has a built-in battery,using the charger to recharge.You can also use solar panels to charge;when the battery is low, insert thecharge,charger light shows red light.batteries isfull when the red light turns to green.Note：When the battery power is low,you can hear the alarm ten "beep" every time the motor runs. It indicates the battery needs to be charged. Then plug in the charger with red light.The light turns green when the battery is fully charged.Operating temperatureParameterTypeRechargeable Description Signal wireDM18LE/S0.2N.m12V433.925MHz80RPM
OPERATION GUIDE12PHENOMENON REASONThe motor alarms when it is workingPROCESSING METHODCharge the batteryThe motor is not runninga，Activate the motor after fully chargedb，Set up the match codec，Contact the engineers for after-salesThe voltage is low in the alarm modea，The battery is not activated.b，The emitter is not matched.c，If press P1 button for a long time while with no reaction.may be the power is short-ciralit or the ciralit board or the motor is broken.NUMBER1, The third limit position setting①After the up limit and down limit setting, you can set the third limit point between them as the half open position;Press 2sPress 1sPress 1sPress 1sPress 5sPress 5sPress 5s Press 1sPress 1s Press 1s Press 1sPress 1s Press 1sPress 1sPress 1sPress 5s Press 1sPress 2sPress 2sPress 2sPress 2sPress 2sRun for hint x2Run for hint x2Run for hint x2Run for hint x2Run for hint x2Run for hint x2Run for hint x1Run for hint x1Run for hint x1 Run for hint x1 Run for hint x1Run for hint x1Run for hint x1Run for hint x2Run for hint x1Run for hint x1 Run for hint x1If you need to reverse the rotateon of the motor controlled by the emitter,please run the reverse of direction setting(as lists in the second point of the P1 button setting)Button specificationP2 P2P24 Add EmitterP2 →P2 →P2 P2 →P2 →P2 5 Delete one emitter3 Dot-move/Continuous moving function switch switch 2, The third limit cancel (P2→Stop→Stop)P1 BUTTON OPERATION2, Set up limit3, Set down limit( Up→Up+Stop)P2P2P2 P2P2(Down→Stop+Down)Run for hint x32 The third limit position setting1 Fine-tune up/down limit positionEnter the limit setting modeNotes: Repetitive operation dot-move and continuous moving function switching cycle, under the dot-move function, according to the upor down button more than 2S release motor linkage operation.or orDot-move Continuous movingDot-move functionContinuous movingfunction++++Adjust the new up limit pointAdjust the new down limit point+Confirm the new up limit pointConfirm the new down limit point++++orFACTORY MODEFACTORY MODEUSER MODEFunctions that can be operated under any modeNote: After setting up the up and down limit into user mode.Note: Can not be fine-tune up/down limit position at the same time.loosen P11 Setting upRun for hint x1Run for hint x1loosen P1Set up is okThe blind run downThe blind run upThe blind run down2 The reverse of direction setting Successful change the direction3 limit position1, Enter the limit setting modeConfirm the Blindto stop in the uplimit positionConfirm the Blindto stop in the downlimit positionThe uplimit pointThe downlimit pointSet up is okSet up is okEnter fine-tune up limit modeEnter fine-tune down limit modePress 1sPress 2s Press 2sPress 1s Press 1sPress 1s Press 1s Press 1sLong Press P1loosen P1Long Press P1loosen P1Long Press P1loosen P1Run for hint x2Run for hint x2Run for hint x1Run for hint x1Run for hint x2Run for hint x1Run for hint x1Run for hint x1Dot-move Continuous movingororororPress 1sPress 1s Press 2sPress 1s Press 2sPress 2sAlready set up, down limit positionAny positionThe third limit position(any position)The motor stopsSet up is okSet up is ok②Long press the stop button for 2s,the roller blinds will move to the third limitMethod twoMethod oneNote:Emitter is the one already matched code, while emitter has notEmitter adding is okEmitter adding is okOne emitter is deletedNote:With the same method,you only can delete the emitter not the emitter1, Activate motor for the first time2, The reverse of direction setting3, Restore factory settingsRun for hint x1Run for hint x2Set up is okSuccessful change the directionActivate is okFAULT AND SOLUTIONRecharger or solar rechargeable board port
FCC Statements: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that my cause undesired operation. MODIFICATION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the device. IC Statements: -English: This device complies with Industry Canada RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. -French: Leprésent appareil est conforme aux CNR d'Industrie Canada applicable aux appareils radio Exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement."

Navigation menu