NINGBO DOOYA MECHANIC and ELECTRONIC TECHNOLOGY DM25CE-S DC Tubular motor User Manual

NINGBO DOOYA MECHANIC & ELECTRONIC TECHNOLOGY CO., LTD. DC Tubular motor

User Manual

E:Electronic / Electronic limit + Built-in receiverL1L2Control rangeTTechnical supportEffective transmitting distancemay have de-viation due to actual environmentL1 open L2 partition Emission frequency12V 200m 35m 433.92/868 MHzDM25LETubular Motor SpecificationVersion NO. : A/05Technical supportTTechnical supportRollingRollingDC1651Double-channelemitterDC165315-channelLCD emitterMatchable emitterTTechnical supportDC160215-channelemitterDC306A5-channelemitterDC305ASingle-channelemitterDC1650Single-channelemitterDC313A15-channelemitterDC287Single-channelemitterDC2885-channelemitterDC28915-channelemitterDC316APortable double-channel emitterDC476APortable 9-channelemitterDC26215-channelemitterDC1600Single-channelemitterCButton specificationTTechnical supportDC1653DC165315-channelLCD emitterDC316Able double-nel emitterDC476APortable 9-channelemitterUpStopDownSettingbutton（P2）Setting buttonSetting buttonP2×1 P2×1 P2×1OKEmitter adding is okAAdditionalfunctionAdd EmitterEmitter a is the one already matched code, while emitter b has notBeep onceRun for hintBeep onceRun for hintBeep 7 timesRun for hintEmbP2×1OKP2×1P2×1AAdditionalfunctionAdd EEmitterBeeep onceRuun for hintceBeep onhintRun for P2×1P2×1Up×1Down×1Beep onceRun for hintBeep onceRun for hintBeep 2 timesRun for hintPower onAAdditionalfunctionDot-move settingDot movesetting is okAAdditionalfunctionDelete emitterP2×1 P2×1The emitters all deletedOKStop button ×1To clean up the emitter means deletingall the memory of emitter and limit switch in the motor receiversBeep 5 timesRun for hintPower onAAdditionalfunctionDelete one emitterAAdditionalfunctionDelePower AAdditionalfunctionDeleP2×1ete emPmitteP2×1eronetee one emitP2×1P2×1OKthe eTo clean up emoryall the mewitch switter Emding addoks o×1P2×Beep 5 timesEaisRun for hintStop button ×1tteerP2×1P2×1The b emitter is deletedOKBeep 5 timesRun for hintBeep onceRun for hintP2×1The emitters all deletedThe emittersOKTP2×1OKDown×1BeepRun ×1p oncefor hintPDown×1AAdditionalfunctionDelete limitThe limit is deletedBeep 4 timesRun for hintᴺ Please set the limit position before use. ᴻ When in the group control mode,the setting up,deleting programme,setting limit are unworkable.Connected chargersConnected chargersDM25LE Tubular MotorᴺIt's strictly prohibited to beat the motor in transport ,storage,installation and use process. Please minimize the motor vibration.ᴻIt suggests need recharging please charge the battery for 3hours and make sure itis fully charged before the first use.please charge the battery every 6 monthsOne motor maximum can store 20 channels, over 20 channels, if still need add new emitters, it will be repeating covered last channel.Beep onceRun for hintBeep onceRun for hintBeep onceRun for hintBeep onceRun for hintBeep onceRun for hintIf the voltage is less than 10v, the motor will alarm for10 times to prompt it needs to be charged every timewhen the motor is working.Press the set button on limit head once,the motor run upward,press the set button on limit head once,the motor will stop,press the set button on limit head again,the motor will run downward Long press the set button on limit head for more than 6s, the motor will run for hint,loose it, the motor will beep 2 times ,then motor direction has been changed with the same limits as before; Longpress the set button on limit head for more than 11s, the motor will run for hint,loose it, and beep 3 times ,then it will delete every memory and restore the factory settings;Restore factory settings, the first use of the motor, long press setting button;With the same method,you only can delete the emitter b not the emitter aRepeat setting,function is cancelled;In the dot-move mode,it will movewhen you loose the button
Stop×1×1Stop×1Stop×Stop×1P2×1P2×1Up×1Beep onceRun for hintAAdditionalfunctionCrown installationForbidden drillthrough crown andinner gear wheelCrownAAdditionalfunctionDrive adapter installationAAdditionalfunctionBracket installationAAdditionalfunctionRechargeable Description If the motor already experienced match code,the memory will be cleared if do it againIf you have matched the codes,connect to thepower, the motor will work normally, if not,themotor will beep 1 time and turn to remind you entryP2×1P2×1P2×1motor already experieemory will be clearedhave matched the cothe motor will workwill beep 1 time and turIf the the meIf you power, motor wSet up is ok. The up limit button control the motor clockwise.OKSet up is ok. The down limit button control the motor clockwise.OKPress setting button ofthe motor for 2s.loose itAAdditionalfunctionSetting upDuring the settings, the time between two operation must be shorter than 6s, otherwise it will quit the settingBeep 6 timesRun for hintBeep 6 timesRun for hintBeep onceRun for hintBeep once Beep onceBeep onceRun for hintBeep onceRun for hintBeep onceRun for hintBeep onceRun for hintBeep 3 timesRun for hintBeep 3 timesRun for hintBeeRunP2×1ehintUp×1Beep onceRun for hep oncen for hintP2×1 Up×1×1Up×1Stop×1Stop×1Stop×1AAdditionalfunctionSet up / down limit positionRun for hint Run for hintpStop×1Run for hintRunfor hintOKķ It is invalid when the up limit and down limit are at the same locationĸ After limit settingˈwith power and memory function;Ĺinto the match-code status 2 minutes later, it will quit out the setting limits status automatically Stop×5Stop×5Confirm the Blindto stop in the down limit positionThe uplimit pointThe downlimit pointThe motor stopsThe motor stopsSetting is okSetting is okSetting is okConfirm the Blindto stop in the uplimit positionDown×1Beep 4 timesRun for hintBeep onceeverytimeBeep onceeverytimeBeep onceRun for hint OKStop×1Stop×1 Stop×1The motor stopsķ After the up limit and down limit setting, you can set the third limit point between them as the half open position;ĸ The third limitpoint will be cancelled as the cancellation of limit and code matching;ĹLong press the stop button for 3s,the roller blinds will move tothe third limit, if the motor is in the dot-move status, long press the stop button for 3s,the motor will move to the down limit firstly,then move to the third limit.The third limit position settingAAdditionalfunctionThe third limit position settingAlready set up, down limit positionThe uplimitpositionThe downlimitposition The thirdlimit position（any position）Every time interval not less than 1 secondThe motor has a built-in battery,using thecharger DC264(1.0Nm and 1.1Nm motor) torecharge.You can also use solar panels DC683Bto charge;when the battery is low, insert thecharge,charger light shows red light.batteries isfull when the red light turns to green.Beep 3 timesRun for hintStop××1Every time innot less than onceor hintoppsOKAlready set up, down limit positionplimitpositione downlimitposition The thirdlimit position（any position））Beep onceRRun for hintStop×The mBeep oRun fo1motor stoP2×1The third limit position cancelledPower onUp×1Down×1ᴺIn the process of adjusting the up / down limit: when the motor moving up or down, press the setting button once, the motorwill be under the step-moving status,press the setting button again to quit the step-moving statusᴻThe step-moving status: themotor will run up or down by the way of step-moving so that the limit position can be adjusted more correctlyDC264DC683B
FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 　 Reorient or relocate the receiving antenna. 　 Increase the separation between the equipment and receiver. 　 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 　 Consult the dealer or an experienced radio/TV technician for help.

Navigation menu