NXP Laboratories UK JN5168IT00 JN5168-RD6040-IoT Gateway User Manual IoT Gateway Kit Getting Started
NXP Laboratories UK Ltd JN5168-RD6040-IoT Gateway IoT Gateway Kit Getting Started
Contents
Manual
JN5168-RD6040 IoT Gateway Kit Getting Started Introduction The NXP ‘Internet of Things’ (IoT) Gateway enables the control of wireless nodes in a WPAN from IP-connected devices in a LAN or WAN (e.g. smart phones, tablets and laptops). It is used with a conventional IP router (which acts as a DHCP server) to provide an interface between the LAN/WAN and WPAN domains. The gateway is designed around the NXP LPC3240 microcontroller and NXP JN5168 wireless microcontroller. The LPC3240 device provides a Linux-capable processing platform for the LAN/WAN interface. The JN5168 device provides the processing platform for the WPAN interface as well as 2.4GHz radio communication with the WPAN. Kit Contents Check the contents of the kit, which are listed below. • • • • IoT Gateway unit * Universal 12V DC power supply unit ** Swivel SMA antenna 1-metre RJ45 Ethernet cable Before using the IoT Gateway, make sure you attach the supplied antenna to the SMA connector on the unit. * RF information: IEEE 802.15.4 Tx/Rx, frequency range 2400–2483.5 MHz, 2 dBm Operating temperature: 0ºC to 40ºC (32ºF to 104ºF) Operating humidity: 10% to 85% relative humidity (non-condensing) ** Mass Power SFF1200100U1BA or Stontronic T5148RW Using the IoT Gateway The IoT Gateway is supplied pre-programmed with the JenNet-IP Border-Router software, which is described in the Border-Router Application Note (JN-AN-1110) available from the NXP Wireless Connectivity TechZone (web address over-page). This allows the gateway to be used with the JenNet-IP Smart Home Demonstration that is pre-programmed into the components of the NXP JN516x-EK001 Evaluation Kit. This kit and demonstration are fully described in the JN516x-EK001 Evaluation Kit User Guide (JN-UG-3093), also available from the TechZone. JN-UG-3096 v1.1 © NXP Laboratories UK 2013 The Smart Home Demonstration represents a typical JenNet-IP system in which a WPAN of lights can be controlled from a PC located in a LAN or WAN. Normally, the interface between the WPAN and LAN/WAN domains is provided by a Linksys router and a JN5168 USB Dongle (both supplied in the evaluation kit). The IoT Gateway can replace the USB dongle in this demonstration, with the gateway providing the processing platform for the JenNet-IP LAN/WAN and WPAN stacks as well as radio communication with the WPAN. The Linksys router must be connected to the IoT Gateway via an Ethernet cable (supplied in this kit). The resulting system is shown below. PC Issues control commands via http interface Light Light Carrier Board Carrier Board Ethernet LAN (IP) JenNet-IP WPAN (IEEE 802.15.4) Remote Control Unit NXP Light Light Carrier Board Ethernet Standard Router IoT Gateway Carrier Board Co-ordinator In setting up and using the above demonstration system, the instructions provided in the JN516x-EK001 Evaluation Kit User Guide remain valid with the exception of the references to the JN5168 USB Dongle and the IPv4 address of the BorderRouter. In the instructions, the IPv4 address 192.168.11.1 must be replaced with the dynamically assigned (DHCP) IPv4 address of the IoT Gateway. Note: Any standard IP router can be used as the DHCP server instead of the Linksys router (the JenNet-IP firmware in the Linksys router is no longer required). For online support resources, Declarations of Conformity and other compliance information for this and other JN516x products, visit the NXP Wireless Connectivity TechZone: www.nxp.com/techzones/wireless-connectivity NXP Laboratories UK Ltd, Furnival Street, Sheffield, S1 4QT, United Kingdom JN-UG-3096 v1.1 © NXP Laboratories UK 2013
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Author : NXP Create Date : 2013:10:08 15:15:44+01:00 Modify Date : 2013:10:08 15:17:55+01:00 Subject : Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2013:10:08 15:17:55+01:00 Creator Tool : Acrobat PDFMaker 10.1 for Word Document ID : uuid:24238b29-8414-4cc7-8912-fd19abf36b57 Instance ID : uuid:aa2ec4e2-aae8-45dd-889a-a5926f000e0b Format : application/pdf Title : IoT Gateway Kit Getting Started Description : Creator : NXP Producer : Adobe PDF Library 10.0 Source Modified : D:20131008141454 Company : Microsoft Page Layout : OneColumn Page Count : 2 Warning : [Minor] Ignored duplicate Info dictionaryEXIF Metadata provided by EXIF.tools