NXP Semiconductors USBKW41Z USB-KW41Z Packet Sniffer USB Dongle User Manual USB KW41Z Quick Reference Guide

Download:
Mirror Download [FCC.gov]
Document ID	3208889
Application ID	mEZ4vR1MW/FXWHFGg6+tfg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	34.75kB (434331 bits)
Date Submitted	2016-11-27 00:00:00
Date Available	2016-11-27 00:00:00
Creation Date	2017-12-18 09:53:07
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-12-18 09:53:07
Document Title	USB-KW41Z Quick Reference Guide
Document Creator	Adobe InDesign CC 2015 (Macintosh)
Document Author:	NXP Semiconductors

Quick Start Guide
USB-KW41Z
FREEDOM DEVELOPMENT PLATFORM
Quick Start Guide
GET TO KNOW THE USB-KW41Z
OpenSDA
MCU
KW41Z
SWD
Printed
Meander
Antenna
KW41Z
MCU
32 MHz
Crystal
OpenSDA
SWD
Application
Button
Power and
Application
LEDs
KW41Z
Reset
OpenSDA
Reset
Figure 1: USB-KW41Z Board Components
www.nxp.com
HOW TO GET STARTED
1.
Plug in the USB-KW41Z board to a PC.
A green power LED and a red application
LED will illuminate.
2.
USB-KW41Z comes pre-programmed with
a Bluetooth Smart® sniffer application.
3.
Explore more out-of-box demos and download software
and tools on www.nxp.com/USB-KW41Z/startnow.
4.
Enjoy your design freedom with the USB-KW41Z.
SUPPORT
Visit www.nxp.com/support for a list
of phone numbers within your region.
WARRANTY
Visit www.nxp.com/warranty for
complete warranty information.
Get Started
Download installation
software and documentation
under “Jump Start Your Design”
at www.nxp.com/usb-kw41z.
www.nxp.com
NXP and the NXP logo are trademarks of NXP B.V. All other product or service names are the property of
their respective owners. © 2016 NXP B.V.
Document Number: USBKW41ZQRG REV 0
Agile Number: 926-29102 REV A
FCC NOTE：
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Any
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. End users must follow
the specific operating instructions for satisfying RF exposure
compliance. To maintain compliance with FCC RF exposure
compliance requirements, please follow operation instructions
as documented in this manual. This transmitter must not be colocated
or operating in conjunction with any other antenna or
transmitter. The availability of some specific channels and/or
operational frequency bands are country dependent and are firmware
programmed at the factory to match the intended destination.
The firmware setting is not accessible by the end user.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 1
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:5002efcf-a689-11f2-0000-02c7314339d4
Producer                        : GPL Ghostscript 9.18
Modify Date                     : 2017:07:21 23:31:47Z
Create Date                     : 2017:07:21 23:31:47Z
Creator Tool                    : UnknownApplication
Document ID                     : uuid:5002efcf-a689-11f2-0000-02c7314339d4
Format                          : application/pdf
Title                           : Untitled

EXIF Metadata provided by EXIF.tools