Nad C541I Users Manual Cover

Nad-Electronics-C541I-Users-Manual-475595 nad-electronics-c541i-users-manual-475595

C541i to the manual a54b65b7-f94d-47d2-a593-cc455d9f6c36

2015-02-05

: Nad Nad-C541I-Users-Manual-493045 nad-c541i-users-manual-493045 nad pdf

Open the PDF directly: View PDF .
Page Count: 10

Owner’s Manual

C541i

Compact Disc Player

Warning: To reduce the risk of fire or electric shock, do not

expose this unit to rain or moisture.

The lightning flash with an arrowhead symbol within an equilateral

triangle, is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to

alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature accompanying

the product.

Do not place this unit on an unstable cart, stand or tripod, bracket

or table. The unit may fall, causing serious injury to a child or adult

and serious damage to the unit. Use only with a cart, stand, tripod,

bracket or table recommended by the manufacturer or sold with

the unit. Any mounting of the device on a wall or ceiling should

follow the manufacturer’s instructions and should use a mounting

accessory recommended by the manufacturer.

An appliance and cart combination should be moved with care.

Quick stops, excessive force and uneven surfaces may cause the

appliance and cart combination to overturn.

Read and follow all the safety and operating instructions before

connecting or using this unit. Retain this notice and the owner’s

manual for future reference.

All warnings on the unit and in its operating instructions should be

adhered to.

Do not use this unit near water; for example, near a bath tub,

washbowl, kitchen sink, laundry tub, in a wet basement or near a

swimming pool.

The unit should be installed so that its location or position does not

interfere with its proper ventilation. For example, it should not be

situated on a bed, sofa, rug or similar surface that may block the

ventilation openings; or placed in a built-in installation, such as a

bookcase or cabinet, that may impede the flow of air through its

ventilation openings.

The unit should be situated from heat sources such as radiators,

heat registers, stoves or other devices (including amplifiers) that

produce heat.

The unit should be connected to a power supply outlet only of the

voltage and frequency marked on its rear panel.

The power supply cord should be routed so that it is not likely to be

walked on or pinched, especially near the plug, convenience

receptacles, or where the cord exits from the unit.

Unplug the unit from the wall outlet before cleaning. Never use

benzine, thinner or other solvents for cleaning. Use only a soft

damp cloth.

The power supply cord of the unit should be unplugged from the

wall outlet when it is to be unused for a long period of time.

Care should be taken so that objects do not fall, and liquids are not

spilled into the enclosure through any openings.

This unit should be serviced by qualified service personnel when:

A. The power cord or the plug has been damaged; or

B. Objects have fallen, or liquid has been spilled into the unit; or

C. The unit has been exposed to rain or liquids of any kind; or

D. The unit does not appear to operate normally or exhibits a

marked change in performance; or

E. The device has been dropped or the enclosure damaged.

DO NOT ATTEMPT SERVICING OF THIS UNIT

YOURSELF. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL

Upon completion of any servicing or repairs, request the service

shop’s assurance that only Factory Authorized Replacement Parts

with the same characteristics as the original parts have been used,

and that the routine safety checks have been performed to

guarantee that the equipment is in safe operating condition.

REPLACEMENT WITH UNAUTHORIZED PARTS MAY RESULT IN FIRE,

ELECTRIC SHOCK OR OTHER HAZARDS.

ATTENTION

POUR ÉVITER LES CHOC ELECTRIQUES, INTRODUIRE LA

LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE

CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU

FOND.

CAUTION

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF

PLUG TO WIDE SLOT FULLY INSERT.

If an indoor antenna is used (either built into the set or installed

separately), never allow any part of the antenna to touch the metal

parts of other electrical appliances such as a lamp, TV set etc.

CAUTION

POWER LINES

Any outdoor antenna must be located away from all power lines.

OUTDOOR ANTENNA GROUNDING

If an outside antenna is connected to your tuner or tuner-

preamplifier, be sure the antenna system is grounded so as to

provide some protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code, ANSI/NFPA No.

70-1984, provides information with respect to proper grounding of

the mast and supporting structure, grounding of the lead-in wire to

an antenna discharge unit, size of grounding conductors, location of

antenna discharge unit, connection to grounding electrodes and

requirements for the grounding electrode.

a. Use No. 10 AWG (5.3mm2) copper, No. 8 AWG (8.4mm2)

aluminium, No. 17 AWG (1.0mm2) copper-clad steel or bronze

wire, or larger, as a ground wire.

b. Secure antenna lead-in and ground wires to house with stand-off

insulators spaced from 4-6 feet (1.22 - 1.83 m) apart.

c. Mount antenna discharge unit as close as possible to where lead-

in enters house.

d. Use jumper wire not smaller than No.6 AWG (13.3mm2) copper,

or the equivalent, when a separate antenna-grounding electrode

is used. see NEC Section 810-21 (j).

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL

CODE INSTRUCTIONS CONTAINED IN ARTICLE 810 - RADIO AND

TELEVISION EQUIPMENT.

NOTE TO CATV SYSTEM INSTALLER: This reminder is provided to

call the CATV system installer’s attention to Article 820-40 of the

National Electrical Code that provides guidelines for proper

grounding and, in particular, specifies that the ground cable ground

shall be connected to the grounding system of the building, as close

to the point of cable entry as practical.

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

ATTENTION

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

IMPORTANT SAFETY INSTRUCTIONS

FRONT PANEL CONTROLS

REAR PANEL CONNECTIONS

CLASS 1 LASER product

LUOKAN 1 LASERPLAITE

KLASS 1 LASERAPPARAT

THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B LIMITS

FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS AS SET OUT

IN THE RADIO INTERFERENCE REGULATIONS OF THE CANADIAN

DEPARTMENT OF COMMUNICATIONS.

LE PRESENT APPAREIL NUMVERIQUE N'EMET PAS DE BRUITS

RADIOELECTRIQUES DEPASSANT LES LIMITES APPLICABLES AUX

APPAREILS NUMERIQUES DE LA CLASSE B PRESCRITES DANS LE

REGLEMENT SUR LE BROUILLAGE RADIO ELECTRIQUE EDICTE PAR LE

MINISTERE DES COMMUNICATIONS DU CANADA.

WARNING! INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED.

AVOID EXPOSURE TO BEAM.

VORSICHT! UNSICHTBARE LASERSTRAHLEN TRITT AUS, WENN DECKEL GEÖffnet und

wenn sicherheitsverriegelung ÜberbrÜckt ist. Nicht dem strahl aussetzen.

ADVARSEL - USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAFBRYDERE ER

UDE AF FUNKTION.UNDGÅ UDSÆTTELSE FOR STRÅLUNG.

ADVARSEL - USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG SIKKERHEDSLÅS

BRYTES. UNNGÅ EKSPONERING FOR STRÅLEN.

VARNING - OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRRAR ÄR

URKOPPLADE. STRÅLEN ÄR FARLIG.

VARO! - AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA

NÄKYMÄTÖNNTÄ LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

C 541i

DIGITAL

OPTICAL

OUT

IR INIR IN

ININ

TRIGGERTRIGGER TRIGGER SWITCHTRIGGER SWITCH

OFF OFF AUTOAUTO

4567

REMOTE CONTROL

STOP/

OPEN/

CLEAR

OFF

SKIP

SCAN

PLAY

REPEAT

+10

RANDOM

TIME

21 PAUSE

PROGRAM DELETE

CD 3

2001 NAD C521i/C541i

NAD C541i Compact Disc Player

Install the NAD C541i Compact Disc player on a level, vibration-

free surface. (Severe vibration, or operation in a tilted position,

may cause the player to mis-track.) The player may be stacked

with other stereo components, as long as there is adequate

ventilation around it. If the player is placed in close proximity to

a radio tuner (AM or FM), a VCR, or a television set, the operation

of its digital circuits may produce static that would interfere with

reception of weak broadcast signals. If this occurs, move the CD

player away from other devices or switch it off when viewing or

listening to broadcasts.

REAR PANEL CONNECTIONS

1. LINE OUTPUT

Connect a cable from these jacks to your amplifier. Plug one end

of a twin RCA-to-RCA lead into the L (upper) and R (lower) output

jacks. Connect the other end of the cable to your stereo amplifier’s

CD input, or to any other “line-level” input jacks (such as the

AUXiliary inputs). Do NOT connect this cable to the amplifier’s

PHONO input jacks. The RCA sockets on your NAD C541i are

colour coded for convenience. Red and white are Right and Left

audio respectively, and yellow for NAD Link and Digital Out.

Ensure that leads and sockets are not damaged in any way and all

sockets are firmly pushed home.

2. DIGITAL OPTICAL & COAXIAL OUTPUT

The digital playback signal is available at this output jack. The

serial data output is taken after the error correction but before the

digital-to-analogue conversion and filtering. The output is

transformer-isolated from the built-in D-to-A circuits. It may be

connected to any digital signal processor that conforms to the

Sony/Philips (SPDIF) standard.

To use the digital output, connect a cable from this jack to the “CD

Digital” or equivalent input on a digital processor or recorder. For

QUICK START best results, the cable should be a 75 ohm coaxial cable of the

type used for video signals, with an RCA phono plug at each end

or the cable should be an optical cable terminated with a TOS

Link connector. (To distinguish them from similar phono-plug

cables used for analogue audio signals, video and digital signal

cables often are colour-coded with yellow plugs.)

3. NAD LINK IN/OUT

The NAD-Link connector is used to pass commands from other units

fitted with NAD-Link connectors. This allows centralised control of a

complete system, and also allows some of the basic functions of

other NAD components (such as a tuner, or cassette-deck) also

equipped with NAD-Link to be controlled with an NAD system remote

control. To function with such other units, connect the C541i's NAD-

Link Out to the NAD-Link In on the other unit. NAD-Link connectors

can be daisy-chained, IN to OUT, so that a whole system can be

controlled from the remote control facilities of one unit.

NOTES: It is advisable not to connect NAD-Link if these units that

have their own built-in remote control command receiver and are

positioned together, in direct view from the remote control

handset. If you are unsure, try operating the products without

NAD-Link first; If the unit responds to the remote control

command, it will not be necessary to connect NAD-Link.

Never loop the last unit back to the first NAD unit in the NAD-Link

chain. Unplug all units from the mains before connecting or

disconnecting NAD-Link.

4. IR IN

This input is connected to the output of an IR (infrared)

repeater (Xantech or similar), or the IR output of another

component to allow control of the C541i from a remote location.

Ask your dealer or custom installer for further details.

5. TRIGGER IN

The 12V trigger Input allows the C541i to be switched remotely

from STANDBY to ON and vice-versa by ancillary equipment such

as a pre-amp, AV processor etc. The controlling device must be

equipped with a 12V trigger output to use this feature.

6. TRIGGER SWITCH

7. AC LINE CORD

Connect this power cord to an AC mains wall outlet or to an AC

convenience outlet at the rear of your amplifier

Remove the transit screw from the bottom of the unit.

Connect a twin RCA-to-RCA lead from the L (left) and R (right)

Line Output jacks to the corresponding CD inputs on your

amplifier.

Plug in the AC power cord.

Press the green POWER button to turn on the player.

Press OPEN to open the disc drawer.

Place a CD, label side up, in the tray’s circular recess. Be

certain that the disc is centred within the recess.

Press PLAY/PAUSE. The drawer closes automatically, and the

disc begins to play.

At any time you may press SKIP or to select different tracks on

the disc.

Press PLAY/PAUSE if you want to stop play temporarily while

keeping the pickup at its current position on the disc. Press

PLAY/PAUSE again when you want to resume playback. Press

STOP if you want to end play and reset the pickup to the

beginning of the disc.

When the switch is set to the OFF position, the unit ignores

any trigger In command. The front panel buttons and Power

On/Off buttons on remote control toggles between Power On

and Standby Mode. This is the correct setting for most

installations.

For control by an external 12V trigger signal, set the switch

to AUTO position, and the C541i will Power On when the

trigger Input is high (12V present). In this setting, the front

panel and the remote control ON/STANDBY controls are

defeated; only the 12V Trigger Input can turn the C541i ON.

The unit will go to Standby mode if the trigger goes from

high to low (no 12V present). The unit will not go to

standby mode using any button on front panel and remote

control. When the external power is first applied to the unit,

the unit will go to the status directed by Trigger input when

the switch is set to AUTO.

NOTE ON INSTALLATION

IMPORTANT! Before installation, remove the red plastic transit

screw from the bottom of the unit. Remove by turning 90°counter-

clockwise and then pulling it out of its position. Never use force to

remove the screw; refer also to the label attached to the transit

screw. Retain the transit screw, should you need to transport the CD

Player over some distance (e.g. when moving house). To avoid

damage, it is important that the transit screw is replaced.

3. DISPLAY

The display provides information about playback status and about the

optical pickup’s location on the disc. The displayed track/time

information is obtained by reading inaudible “sub-codes” in the disc.

TRACK NUMBER Each disc is segmented into numbered tracks

when the recording is made; typically each numbered track will

correspond to a different song, symphonic movement, etc. These

track numbers are identified on the CD package and are encoded

in the disc by its manufacturer. In some CDs, at the manufacturer’s

option, tracks may be sub-divided into sections identified by Index

numbers. This player does not display Index numbers.

TIME Normally this display shows the time elapsed since the

beginning of the current track. Using the TIME button you can

switch the display to show the remaining number of tracks and

playing time to the end of the disc. When you load a different disc

and use the OPEN button (No. 4) to close the disc drawer, the

display shows the number of tracks and the total playing time of

all the tracks on the disc.

REMAIN REMAIN lights up in the lower-left corner of the display

if you have pressed the TIME button to show the remaining

number of tracks and time of the disc.

REPEAT 1 “REPEAT” and “1” light up respectively in the centre

and upper-left corner during repeat-play of a single track.

“REPEAT” and “ALL” light up during repeat-play of the entire

program or disc

RANDOM When the C541i’s random mode has been selected,

“RANDOM” will be shown in the Display Panel.

CALENDAR DISPLAY TRACK LISTING Displays a list of tracks

available on the disc. As each track is played its number is

blanked out on the Track Listing, giving a simple indication of how

much of the disc has been played and how much remains. The

number for the current track being played blinks. The display

shows up to 16 numbered tracks.

OVER If the loaded disc contains over 16 tracks, “OVER” will light

up in the bottom centre area of the display.

MEMORY During Program Play or programming for Program

Play, MEMORY will light up.

PROGRAM Together with MEMORY, PROGRAM will light up during

playback of a selection of pre-programmed tracks of the disc.

STATUS A right-pointing arrowhead , located near the left

edge of the time display, lights up during PLAY. Two vertical bars

indicate that the player is in PAUSE. In STOP mode the

display reverts to showing the total number of tracks and playing

time of the disc.

no dISC When no disc is present or when you load a disc that

cannot be read (because it is dirty or is upside-down) “no dISC”

lights up in the display.

REMOTE RECEIVER An infrared sensor, located at the right-

hand portion of the display window, receives commands from the

remote control. There must be a clear line-of-sight path from the

remote control to this window; if that path is obstructed, the

remote control may not work.

HDCD®indicator This indicator will light up when an HDCD®

encoded disc is played. For more information on HDCD®refer to

chapter “HDCD”.

4. OPEN

Press this button to open the disc drawer, and press it again to

close the drawer. If this button is pressed while a disc is being

played, playback will stop, the pickup will reset to the beginning of

the disc and the drawer will open. Opening the drawer will also

delete the players memory for Program Play. When the disc drawer

is open, the drawer-closing mechanism can also be activated by

pressing PLAY or by gently pushing the drawer inward.

NOTE: The disc drawer is opened and closed by an internal

motor. Do not close the drawer by hand with the power off.

When the drawer closes, the player scans the disc’s TOC (Table Of

Contents) and displays the total number of tracks and playing time

on the disc. If you press PLAY to close the drawer this information

is skipped, and play commences immediately at Track 1.

5. PLAY/PAUSE

This dual-function button alternates between starting and stopping

playback. Press to start play or to resume play after Pause. During

play, press this button to stop playback temporarily, keeping the

optical pickup at its current position on the disc. The PLAY mode

is identified by a right-pointing arrowhead in the display. The

PAUSE mode is identified by two vertical bars . To resume

playback at the exact point where it stopped, press PLAY/PAUSE

again. If you don’t want to resume play at the same point, you may

use the SKIP and SCAN controls to cue the pickup to a different

starting point before pressing PLAY again.

6. TIME

The TIME button alternates between displaying the elapsed or

remaining tracks and time of the disc or program being played. In

the default setting, the display will indicate the current track

number and time elapsed since the beginning of the track. Press

the button once to display the total number of remaining tracks

and time of the disc or program being played. Press again to

revert to the default, elapsed time display.

7. STOP

Press the STOP button once to stop playback, and re-sets the

pickup to the beginning of the disc. The display reverts to showing

the number of tracks and total playing time on the disc. If the CD

player was programmed to play a selection of tracks, the program

will be retained in the player’s memory. Pressing STOP a second

time will also delete the program. Pressing STOP twice will also

disengage Repeat and Random play if these were engaged.

8. REPEAT

This button engages the Repeat Play mode, an endless-repeat

cycle. Press the Repeat button once to select the REPEAT 1 mode,

in which only the current track is repeated over and over again.

Pressing the Repeat button once again selects the REPEAT ALL

mode, in which the entire disc is played from beginning to end,

over and over again. Press the Repeat button a third time to cancel

the repeat cycle and return to normal operation.

FRONT PANEL CONTROLS

1. POWER ON/OFF

Press this green button to switch on the power to the disc player.

Press again and release to switch the power off. The display will

light up to indicate the unit is switched on and ready for use.

2. DISC DRAWER

To play a disc, press the OPEN button to open the disc drawer.

Place the CD within the large circular recess in the drawer, with

its transparent playing surface facing down. The label must face

UP. CD-3 discs (3-inch CD “singles”) can be played without the

aid of an adapter. Place the disc in the drawer, centered in the

smaller circular recess, with its label facing UP.

NOTE: This player was not designed to accommodate a “damping

disc” placed on a CD, nor two CDs stacked together. It plays audio

CDs, but not discs identified as CD-V, DVD, CD-I, CD-ROM,

or PHOTO CD. Refer also to chapter “A note on CD-R and CD-RW

audio discs”.

9. RANDOM

Engaging the Random Play mode will play all the tracks once on

the CD in a random order. From Stop, press first the RANDOM and

then the PLAY/PAUSE button to engage Random Play mode. During

normal playback the Random Play mode can also be engaged by

pressing the RANDOM button. The current track will stop playing

and the first randomly selected track will commence.

The Random Play mode can be used in combination with the

Repeat Play All mode but not with Program Play mode. When the

C541i is in Random mode “RANDOM” will be shown in the Display

Panel. Press the RANDOM button again to cancel Random Play

mode and return to normal Play mode. Random Play mode can

also be disengaged by pressing the STOP button twice. On the first

press of the STOP button, playback will stop, the second press will

disengage Random Play mode.

10. SCAN

The SCAN button causes the optical pickup to scan backward

through the recording at high speed. This button works only while

the player is in PLAY or PAUSE. After a STOP command, or after

loading a new disc, you must press PLAY before the scan circuit

will work. If Scan is initiated while the player is in PAUSE the scan

is silent; if initiated during PLAY the music will be heard in

fragmentary form at reduced volume as the player scans through

it. For the first approximately 50 seconds of a track, scanning will

be at around 3 times the speed, after which scanning speed

increases to around 15 times faster than normal playing speed.

Use this “audible scan” to cue the player precisely to the spot

where you want to resume play. If you scan back to the beginning

of the disc while playing Track 1, the player automatically reverts

to normal playback.

The SCAN button causes the optical pickup to scan rapidly

forward through the music. The behaviour of this function is

similar to SCAN . If you scan forward to the end of the disc

while playing the final track, the scan will stop and the Time

display will show the table of contents. (There is no “wrap-

around” mode.)

11. SKIP

During playback, press the SKIP button once to skip back to

the beginning of the current track. Press SKIP twice in rapid

succession to skip back to the previous track or previous

programmed track in Program Play mode, once to reach the

beginning of the current track and again to jump to the previous

track. When pressing continuously, the player will skip to previous

tracks repeatedly, concluding at the beginning of the disc

(Track 1) or the first track programmed in Program Play mode.

During playback, press the SKIP once to skip to the beginning

of the next track on the disc or next programmed track in Program

Play mode. Thus, to sample each song, press PLAY and then tap

SKIP after you’ve heard a few seconds of each track. From Stop,

press the SKIP button until you’ve reached the track from

where you want to start playback. Press Play to start playback.

NUMERIC KEYPAD

Using the direct-entry numeric keypad (1 to 10; +10) causes the

player to jump directly to the beginning of a numbered track and

commence play. Thus to play Track 5, simply press 5. To play

Track 20, press: +10, 10. To play Track 36, press: +10, +10,

+10, 6.

PROGRAM

The C541i CD player allows for programmed playback of up to 20

tracks in any desired order. To engage Program Play with your

desired track sequence in the memory:

1. Press PROGRAM. The “MEMORY” indicator will light up. The

display indicates “Pr p:01”, meaning that the player is awaiting

the first Program entry.

2. Use the SKIP or the Direct-Entry Numeric keypad buttons to

select the first track in your planned sequence. The selected

track number will blink in the display.

3. Press PROGRAM to store the selected track number in

memory. The display will revert to show Program-Entry mode

and advance to “Pr p:02”, showing that the player is ready for

your second entry.

4. Repeat Steps 2 and 3 to select and store other track numbers

in memory, up to a maximum of 20 entries. The display will

show “FULL” when 20 tracks have been entered.

5. If you want to review or edit your program entries, press

PROGRAM repeatedly to cycle the display through them. When

the highest program number is displayed, you can enter

additional tracks in the memory by repeating Steps 2 and 3.

6. To play the stored program, press PLAY.”PROGRAM” and

“MEMORY” will appear in the display, indicating that a stored

program is being played. During Program Play the SKIP

buttons will access only the tracks in the program list. So if you

want to play only a portion of a stored program, initiate play

and press SKIP to jump over the programmed tracks that

you don’t want to hear.

The Repeat Play mode can be used in combination with Program

and Random Play modes. When the C541i is in Repeat Play mode

“REPEAT 1” or “ALL” will be shown in the Display Panel. Repeat

Play mode can also be disengaged by pressing the STOP button

twice. On the first press of the STOP button, playback will stop, the

second press will disengage Repeat Play mode.

12. STAND-BY INDICATOR

The Stand-by Indicator turns on in green when the unit is switched

on, and changes to amber when switched to stand-by mode.

REMOTE CONTROL

A wireless remote control is provided with your compact disc

player, enabling you to operate play-back functions from the

comfort of your chair or from virtually anywhere in the room. For

reliable operation there should be a clear line-of-sight path from

the remote control to the front of the CD player. If the player does

not respond to remote commands, it may be that this line-of-sight

path is obstructed by clothing, paper, or furnishings.

Most of the buttons on the remote control handset have the same

effect as the corresponding buttons on the front panel of the disc

player. In addition the handset is equipped with some extra

buttons and functions, such as the numeric keypad and Program

functions.

POWER ON

Press this Green button to switch on the power to the disc player

from Standby mode. The green LED will light up.

POWER OFF

Press this Red button to switch to Standby mode from power on

mode. The amber LED will light up. This indicates that the AC

power is still connected, and that the C541i is ready to receive

an ON command from the remote handset or 12V trigger

(depending on the setting of the trigger switch #6).

The following example presents a step-by-step illustration of how to

program and start Program Play to play tracks 5, 23, 9, 16, and 1.

While the CD player is stopped:

Press on remote control Display shows

PROGRAM Pr p:01

5 5 p:01

PROGRAM Pr p:02

+10, +10, 3 23 p:02

PROGRAM Pr p:03

9 9 p:03

PROGRAM Pr p:04

+10, 6 16 p:04

PROGRAM Pr p:05

1 1 p:05

PROGRAM Pr p:06

PLAY

The Calendar display track listing will indicate the selected

program.

The coil springs should contact the (-) end of each cell. Push the

battery compartment cover back and press gently until it latches.

In some cases, corrosion or fingerprint oil on the battery contacts

may cause poor operation. Remove both cells, rub the metal

contacts at both ends of each cell with a clean cloth or a pencil

eraser, and re-install the cells, being careful to orient them

correctly.

Developed by Pacific Microsonics in the USA, HDCD®(High

Definition Compatible Digital®) is a patented encode/decode

process for delivering the full richness and detail of the recording.

HDCD®encoded CDs sound better because they are encoded with

20-bits of real musical information, as compared to 16-bits for all

other CDs. HDCD®overcomes the limitation of the 16-bit CD

format by using a sophisticated system to encode the additional

four bits onto the CD while remaining completely compatible with

the existing CD format.

The result is a larger dynamic range, a more focused 3-D

soundstage, and natural vocal and musical timbre. An HDCD-

encoded disc played on the HDCD-equipped NAD C541i CD player

produces audibly superior clarity and depth. Enhanced

performance will also be obtained from standard CDs.

The NAD C541i CD player will automatically identify an HDCD®

encoded disc and activate its HDCD®decoder. The red indicator

will light up when it’s playing an HDCD®encoded disc.

CD-R & VD-RW AUDIO DISCS

The C541i can play back CD-R, CDRW audio discs that have been

recorded on a computer or CD-recorder. The quality of CD-R,

CD-RW audio discs varies widely which may affect playability.

Some factors that affect playability:

•The quality of the disc itself. Generally speaking, CD-R, CD-RW

blanks from well-renowned companies give better results

than unbranded ones.

• The quality of CD-recorder or computer CD re/writer. Some

recorders and writers produce better results than others.

•The CD-R & CD-RW was created with high-speed writing. In

7. To terminate program play, press STOP. However the stored

track list remains in memory; if you want to play the program

again, simply press PLAY again. If you want to edit the program,

press PROGRAM repeatedly to review the list and change. To

add tracks, press the PROGRAM button until the highest

program number is displayed.

8. To clear the program memory, press STOP twice, OPEN/CLOSE

to open the drawer, or switch off the POWER.

DELETE

The C541i CD Player allows to user to delete unwanted tracks in

any desired order in either the Program Mode or the Stop Mode.

To Delete tracks, use the sequence of commands below.

In Program Mode:

Press DELETE. The display indicates "dE d:01"; the player is

now ready for first Delete entry. "dE" will change to first

memory track after 1 second.

Use the I <<SKIP & SKIP>> I buttons to select the first

track you would like to delete. The track number will flash.

Press DELETE again to store the selected track number in

memory. The selected track number will be deleted in the

display. The display will advance to next location. This

showing that the player is ready for your second entry.

Repeat Steps 2 and 3 to select the delete the track numbers

in memory, up to a maximum of 20 entries but cannot delete

track above track 25.

To play the stored program, just press PLAY. During playing,

the SKIP buttons will access only the tracks still listed. The

deleted songs are not listed.

To clear the memory, press STOP twice, OPEN/CLOSE to

open the drawer, or switch off the power.

In Stop Mode:

Press DELETE. The display indicates "dE d:01" with total

track time. The player is ready for the first Delete entry.

Use the Direct-Entry Numeric keypad buttons to select the

first track you would like to delete. The selected track

number will be deleted in the calendar display and the

updated total playing time is shown on display.

Repeat Steps 2 to select the track numbers you would like to

delete, up to a maximum of 25 entries but cannot delete

track above track 25.

To play the remaining tracks, just press PLAY. During playing,

the SKIP buttons will access only the tracks still listed. The

deleted songs are not listed.

5. To clear the memory, press STOP, OPEN/CLOSE to open the

drawer, or switch off the power.

NOTE: In the Program-entry mode, the SKIP and

buttons have a “wrap-around” function: if you SKIP Back

repeatedly from Track 01, the number counts down from the final

track on the disc. This provides a convenient way to select high-

numbered tracks.

INSTALLING AND REPLACING BATTERIES

The remote control requires two 1.5-volt AAA-size (i.e. UM-4 or

IEC RO3) cells. Alkaline cells are recommended, to obtain

maximum operating life. To open the battery compartment, place

your fingertip in the recess on the rear of the remote control, push

against the flexible edge of the battery cover and lift the cover

upwards. Install fresh cells, orienting them as shown on the

diagram within the compartment.

The Calendar display will indicate remaining track listing. After

completing playback, the C541i will automatically stop, and the

display will again show all the tracks contained on the inserted

CD.

, HDCD®, High Definition Compatible Digital®and

Pacific Microsonics™ are either registered trademarks or

trademarks of Pacific Microsonics, Inc. in the United States and/or

other countries.

HDCD system manufactured under license from Pacific

Microsonics, Inc. This product is covered by one or more of the

following patents: In the USA: 5,479,168, 5,638,074, 5,640,161,

5,808,574, 5,838,274, 5,854,600, 5,864,311, 5,872,531, and in

Australia: 669114. Other patents pending.

ABOUT THE OPTICAL PICKUP

The Compact Disc player uses a solid-state semi-conductor diode

laser, mounted on a tracking servo-mechanism, to play the disc.

The laser illuminates the track of microscopic pits representing

the digital data bits, while photo-diodes detect the reflected

illumination from the disc and convert it into an electronic signal

which is then decoded to recover the musical waveform in each

stereo channel.

You cannot see the laser operating, because it operates at

wavelength of 7800 Angstroms, which is in the infrared and thus

invisible to the human eye.

The Compact Disc player is completely safe for children to use.

The laser operates at very low power and is concealed within the

player mechanism. Even when the player is disassembled, the

laser remains sealed within an optical system that causes its light

to focus only 1 millimeter from the lens and then diverge rapidly,

reducing its intensity to negligible levels.

TROUBLESHOOTING

NO POWER WHEN THE POWER BUTTON

IS SET TO ON

• Poor or no power plug connection at

•

Trigger switch is set to Auto

the AC outlet

• Insert the power plug firmly into the AC

outlet.

SYMPTOM POSSIBLE CAUSE SOLUTION

DISC PLAY DOES NOT START • The disc is loaded upside down

• The disc is too dirty

• Reload the disc with the label side UP

• Clean the disc

NO SOUND • Incorrect audio cable connections

• Incorrect amplifier/receiver operation

• Connect the CD player to the

amplifier/receiver correctly

• Make sure that the input selector on

your amplifier or receiver is set to CD

SOUND SKIPS • The CD player is subject to vibration or

physical shock from external sources

• Change the installation location

REMOTE CONTROL DOES NOT WORK • Batteries in Remote Control handset

have expired

• Object obscuring remote sensor

on the player

• Replace batteries

• Remove any objects directly in front of

the player

A “HUMMING” SOUND CAN BE HEARD • Loose cable connections • Check the cable connections,

particularly the phono connecting

cables

flawed discs that are unplayable on some other players.

Nevertheless, the discs should not be abused or handled

carelessly. For best results, grasp the disc only by its edges.

CLEANING DISCS

Soiled discs may be cleaned by wiping with a soft cloth, either dry

or moistened, with water. Do NOT use conventional LP record-

cleaning products (cleaning solutions, sprays, treated cloths, or

anti-static preparations), nor any kind of chemical solvent

(alcohol, benzene, et al). A severely soiled disc may be washed in

a warm-water spray, possibly with a small amount of a mild kitchen

detergent added, and then wiped dry with a clean, soft towel.

When cleaning the disc, use only RADIAL strokes (from centre to

edge). Never use a circular wiping motion like that used for

cleaning ordinary LP records, because in wiping the disc there is a

risk of scratching it. A radial scratch will do the least harm because

it affects only a small portion of each circular data track, which can

be fully compensated by the player’ s error-correction circuits. But

a circular scratch that follows a data track may damage such a long

continuous segment of data that it cannot be corrected.

MAINTENANCE

At periodic intervals, open the disc drawer and wipe with a damp

cloth to remove any loose dust.

HANDLING COMPACT DISCS

Handle Compact Discs with care. The playback of a disc will not

be impaired by small dust particles, a few light fingerprints, or

slight scratches. But large scratches, or a thick layer of oily

fingerprints, can pre-vent the player from tracking the disc.

(Incidentally, although the tracking optical pickup “plays” the

disc through its clear side, the actual data surface is embedded

directly beneath the label, protected only by a very thin coating of

lacquer. So a scratch that cuts through the label may damage the

disc more than a similar scratch on the transparent “playing”

surface. Thus you should treat both surfaces of the disc with

care.) Severe scratches or fingerprints may cause the player to

mis-track (skipping ahead, or repeating the same passage). Less

severe damage may produce very brief bursts of high-frequency

noise. The tracking and error-correction circuits of this NAD CD

player are unusually sophisticated, providing secure tracking of

general, the quality of a CD-R, CD-RW are better when produced at a

lower speed against a higher speed on the same recorder or re/writer.

Switch the trigger switch to off position

•

IMPORTANT NOTICE

DISC PLAYABILITY

This CD Player is designed to play musical program material only, on CD, CD-R, and CD-RW discs recorded

in the 16 bit 44.1 kHz PCM Compact Disc format. It is not designed to play any other disc format, or discs

with data or pictures.

WARNING

Attempting to play discs with non-musical programs may result in damage to your playback system.

AVIS IMPORTANT

DISQUES POUVANT ÊTRE LUS PAR CE LECTEUR

Ce Lecteur CD a été conçu pour lire les enregistrements musicaux uniquement, sur les CD, CD-R ou CD-RW

enregistrés sous format Compact Disc 16 bits 44,1 kHz PCM. Il ne peut lire aucun autre format de disque et n’est

pas capable de lire un disque comportant des données ou des images.

ATTENTION

Toute tentative de lire un disque comportant un enregistrement autre que musical entraînera une détérioration

de votre chaîne de lecture.

WICHTIGER HINWEIS

ABSPIELBARKEIT VON CDS

Dieser CD-Player eignet sich ausschließlich zum Abspielen von Musikmaterial auf CD, CD-R und CD-RW, das

im Compact-Disc-PCM-Format mit 16-Bit/44,1 kHz aufgezeichnet worden ist. Er wurde nicht zur Wiedergabe von

anderen CD-Formaten oder CDs mit Daten oder Bildern entwickelt.

ACHTUNG

Das Abspielen von anderen als Musik-CDs kann zu Schäden an Wiedergabesystemen führen.

AVISO IMPORTANTE

CAPACIDAD DE ESCUCHA DE DISCOS

Este tocadiscos CD se ha diseñado para escuchar material de programas musicales solamente, con discos CD,

CD-R y CD-RW grabados en formato de Disco compacto de 16 bites 44,1 kHz PCM. No se ha diseñado para

escucha de cualquier otro formato de disco, ni para discos con datos o imágenes.

ADVERTENCIA

Si se intenta escucha de discos que no tienen programas musicales se puede dañar su sistema de escucha.

AVVISO IMPORTANTE

RIPRODUCIBILITÁ DEL DISCO

Questo CD player è stato progettato per riprodurre esclusivamente materiale di programmi musicali su dischi

CD, CD-R e CD-RW registrati in formato compact disc PCM 44,1 kHz a 16 bit. Non è stato progettato per

riprodurre alcun altro tipo di formato disco, o dischi contenenti dati o immagini.

AVVERTENZA

Il tentativo di riprodurre dischi contenenti programmi non musicali potrebbe danneggiare l’impianto di

riproduzione.

AVISO IMPORTANTE

CAPACIDADE DE REPRODUÇÃ DO DISCO

O presente Leitor de CD foi concebido para reproduzir apenas material de programação musical de discos CD,

CD-R e CD-RW gravados no formato de disco compacto de 16 bit e 44,1 kHz PCM. Não foi concebido para

reproduzir quaisquer discos de outros formatos nem discos que contenham dados ou imagens.

AVISO

Caso tente reproduzir discos com programação não musical poderá danificar o seu sistema de reprodução.

VIKTIGT

VILKA SKIVOR KAN SPELAS

Denna CD-spelare är enbart framtagen för att återge material innehållande musik, på CD, CD-R, och CD-RW

skivor inspelade med 16 bitar 44.1 kHz PCM CD-format. Den kan inte spela skivor med andra format eller

skivor med data eller bilder.

VARNING

Om man försöker spela skivor med annat innehåll kan detta orsaka skador på avspelningsutrustningen.

P/N: 3050-2311-0

NAD C541i

* ADDENDUM SHEET *

www.NADelectronics.com

C541i Manual 11/01 Printed in the Peoples Rebublic of China

P/N:4301-4166-0

Nad C541I Users Manual Cover

Nad-Electronics-C541I-Users-Manual-475595 nad-electronics-c541i-users-manual-475595

C541i to the manual a54b65b7-f94d-47d2-a593-cc455d9f6c36

Navigation menu

Versions of this User Manual:

Views

Navigation