ENGLISH
Owner’s Manual
SAFETY INFORMATION
EXPLANA
TION OF GRAPHICAL SYMBOLS
EXPLANATION
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in the literature accompanying
the appliance.
PRECAUTIONS
Read the Operating Instructions carefully and completely before operating the unit. Be sure to keep the
Operating Instructions for future reference. All warnings and cautions in the Operating Instructions and on
the unit should be strictly followed, as well as the safety suggestions below.
INST
ALLA
TION
INSTALLA
ALLATION
1 Water and Moisture - The apparatus shall not be exposed to dripping or splashing and that no objects
filled with liquids, such as vases, shall be placed on the apparatus.
2 Heat - Do not use this unit near sources of heat, including heating vents, stoves, or other appliances that
generate heat. It also should not be placed in temperatures less than 5°C (41°F) or greater than 35°C
(95°F).
3 Mounting surface - Place the unit on a flat, even surface.
4 Ventilation - The unit should be situated with adequate space around it so that proper ventilation is
assured. allow 10 cm (4 in.) clearance from the rear and the top of the unit, and 5 cm (2 in.) from each
side. - Do not place on a bed, rug, or similar surface that may block the ventilation openings. - Do not
install the unit in a bookcase cabinet, or airtight rack where ventilation may be impeded.
5 Objects and liquid entry - Take care that objects or liquids do not get inside the unit through the
ventilation openings.
6 Carts and stands - When placed or mounted on a stand or cart, the unit should be moved with care. Quick
stops, excessive force, and uneven surfaces may cause the unit and cart to overturn or fall.
7 Wall or ceiling mounting - The unit should not be mounted on a wall or ceiling, unless specified in the
Operating Instructions.
WARNING! TO REDUCE THE RISK OF FIRE OR ELECTRONIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE
CAUTION: TO PREVENT ELECTRIC SHOCK, MA
TCH WIDE BLADE OF PLUG TO WIDE
MATCH
T.
SLOT,, FULL
FULLY
INSERT
SLOT
Y INSER
This product is manufactured to comply with the radio interference requirements of EEC DIRECTIVE
89/366/EEC, 92/31/EC and 93/68/EEC
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, and the double-D symbol are
trademarks of Dolby Laboratories.
”DTS“, ”DTS-ES“ and ”Neo:6“ are trademarks of Digital Theater Systems, Inc.
2
SAFETY INFORMATION
ELECTRIC POWER
1 Power Sources - Connect this unit only to power sources specified in the Operating Instructions, and as
marked on the unit.
ENGLISH
2 Polarization - As a safety feature, some units are equipped with polarized AC power plugs which can
only be inserted one way into a power outlet. If it is difficult or impossible to insert the AC power plug into
an outlet, turn the plug over and try again. If it still does not easily insert into the outlet, please call a
qualified service technician to service or replace the outlet. To avoid defeating the safety feature of the
polarized plug, do not force it into a power outlet.
3 AC power cord - When disconnecting the AC power cord, pull it out by the AC power plug. Do not pull
the cord itself.
• Never handle the AC power plug with wet hands, as this could result in fire or shock.
• Power cords should be routed to avoid being severely bent, pinched, or walked upon. Pay particular
attention to the cord from the unit to the power socket.
• Avoid overloading AC outlets and extension cords beyond their capacity, as this could result in fire
or shock.
4 Extension cord - To help prevent electric shock, do not use a polarized AC power plug with an extension
cord, receptacle, or other outlet unless the polarized plug can be completely inserted to prevent exposure
of the blades of the plug.
5 When not in use - Unplug the AC power cord from the AC outlet if the unit will not be used for several
months or more. When the cord is plugged in, a small amount of current continues to flow to the unit,
even when the power is turned off.
CAUTION
Modifications or adjustments to this product, which are not expressly approved by the manufacturer, may
void the user’s right or authority to operate this product.
MAINTENANCE
Clean the unit only as recommended in the Operating Instructions.
DAMAGE REQUIRING SERVICE
Have the unit serviced by a qualified service technician if
• The AC power plug has been damaged.
• Foreign objects or liquid have gotten inside the unit.
• The unit has been exposed to rain or water - The unit does not seem to operate normally.
• The unit exhibits a marked change in performance.
• The unit has been dropped, or the cabinet has been damaged
DO NOT A
TTEMPT TO SER
VICE THE UNIT YOURSELF
ATTEMPT
SERVICE
OWNER’S RECORD
For your convenience, record the model number and serial number (you will find them on the rear of your set)
in the space provided below. Please refer to them when you contact your dealer in case of difficulty.
Model No. :
Serial No. :
3
TABLE OF CONTENTS
TABLE OF CONTENTS
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
GETTING THE MOST FROM THE NAD T 753 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
UNPACKING AND SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
What’s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Save the packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Choosing a Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
6
6
6
CONNECTING AM ANTENNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ABOUT THE T 753 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E.A.R.S., Matrix, and Digital Surround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ease of Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Integration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Second Zone (MULTISOURCE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Upgradability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About the HTR 2 System Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
7
7
7
7
8
8
QUICKSTART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Play a DVD Movie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
FRONT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-11
REAR PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13
Attention! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SETTING UP THE T 753 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Dealing With Hum and Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
ABOUT THE ON-SCREEN DISPLA
YS (OSD) AND FRONT
-PANEL READOUT . . . . . . . . . . . . . . . .
DISPLAYS
FRONT-PANEL
Displaying the OSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Navigating the OSD and Making Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speaker Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speaker Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Listening Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel-Balance (Test) Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using an SPL Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting Channel Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speaker Distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting Speaker Distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Advanced Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main/Zone DSP Decoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dolby Digital Surround EX Decoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTS-ES Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Background to OSD ON or OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Temp OSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Creating and Using Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Creating Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recalling Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
15
15
15
15
16
16
16
17
17
17
17
17
17
17
17
17
17
17
18
18
18
USING THE T 753 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Selecting Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Muting the Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Listening to Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
About Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Selecting the Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Tuning Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Setting Radio Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Selecting Radio Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Choosing the FM Mute/ Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
About RDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
About User Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Entering User Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
About DTS and Dolby Digital Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-22
About the T 753’s Listening Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Displaying the Signal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Selecting Listening Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Adjusting Listening Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Surround Sound Channel chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Adjusting Channel Levels “On the Fly” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
To Adjust Channel Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Adjusting the Tone Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4
TABLE OF CONTENTS
26
26
26
26
27
27
27
27
27
28
28
28
28
29
29
29
29
ENGLISH
Using the HTR 2 Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controlling the T 753 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Learning Codes From Other Remotes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Punch-Through . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Copy a Command From Another Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Macro Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recording Macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Executing Macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Key-Illumination Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Factory Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delete Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loading Code-Libraries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of HTR 2 Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the ZR 2 Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trigger Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assigning the Trigger Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
SPECIFICA
TIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
SPECIFICATIONS
GETTING THE MOST FROM THE NAD T 753
Thank you for choosing NAD.
The T 753 A/V Surround Sound Receiver is a technologically advanced and highly capable product — yet we
have invested great effort in making it simple and easy to use. The T 753 delivers a range of genuinely
useful options for surround sound and stereo listening alike, using powerful digital signal processing and
superbly accurate digital-audio circuitry. However, we have also been careful to ensure that the receiver is
as musically transparent and spatially accurate as possible, incorporating much of what we’ve learned from
a quarter-century’s experience designing audio and home-theater components. As with all our products,
NAD’s “Music First” design philosophy guided the T 753’s design, such that it can confidently promise you
both state-of-the-art surround home-theater and audiophile-quality music listening for years to come.
We encourage you to take a few minutes now to read right through this manual. Investing a little time here
at the outset might save you a good deal of time later, and is by far the best way to ensure that you make
the most of your investment in the NAD T 753, and get the most from this powerful and flexible hometheater component.
One more thing: We urge you to register your T 753 ownership on the NAD Worldwide Web site:
< http://NADelectronics.com/w/Registration.html >
For warranty information contact your local distributor.
5
UNPACKING AND SETUP
WHA
T’S IN THE BOX
WHAT’S
Packed with your T 753 receiver you will find:
•
•
•
•
•
•
An AM loop antenna
A FM ribbon-wire antenna with balun
A removable AC cable (if you wish, any IEC-standard AC cable of suitable wattage may be substituted).
The HTR 2 remote control with 4 (four) AAA batteries.
The ZR 2 zone remote control with 3V CR2025 battery.
This owner’s manual.
Save the packaging
Please save the box and all of the packaging in which your T 753 arrived. Should you move or otherwise
need to transport your receiver, this is by far the safest container in which to do so. We’ve seen too many
otherwise perfect components damaged in transit for lack of a proper shipping carton, so please: Save that
box!
CHOOSING A LOCA
TION
LOCATION
Choose a location that is well ventilated (with at least several inches to both sides and behind), and that will
provide a clear line of sight, within 25 feet/8 meters, between the receiver’s front panel and your primary
listening/viewing position—this will ensure reliable infrared remote control communications. The T 753
generates a modest amount of heat, but nothing that should trouble adjacent components. It is perfectly
possible to stack the T 753 atop other components, but the reverse usually should be avoided. Nonetheless,
it is generally preferable that the T 753 stand alone. It is especially important that sufficient ventilation be
provided; if you are contemplating locating the T 753 within a cabinet or other furniture, consult your NAD
audio/video specialist for advice on providing adequate airflow.
CONNECTING AM ANTENNA
ASSEMBLING THE AM LOOP ANTENNA
1 Rotate the outer frame of the antenna.
2 Insert the bottom edge of the outer frame into the groove on the stand.
Insert into the groove
6
3 Extend the antenna cord.
ABOUT THE T 753
Though the T 753 is among the most technically sophisticated A/V receivers, we worked hard to make it one
of the most musically transparent home-theater components available as well; this is what we mean by
NAD’s “Music First” design philosophy. Here are just a few examples:
ENGLISH
• The T 753 uses NAD’s proprietary Power Drive™ amplifier technology for all channels to preserve
accurate, linear reproduction regardless of the loudspeaker. This uniquely efficient power-supply topology provides the real-world benefits of high dynamic power that remains uncompromised by lowimpedance speakers. The result is dynamic, detailed, “un-receiver-like” sound in stereo and multichannel
modes alike. NAD’s exclusive Soft Clipping™ circuitry further enhances sound quality and dynamic
potential.
• High-performance components used throughout the receiver’s analog audio circuits maximize quality from
all sources, including multichannel analog sources such as DVD-Audio and SACD.
• Preamp output (all channels) and main-amp input jacks make potential expansion as flexible as possible.
• A Second set of Speaker terminals (Speakers B) for remote listening.
• Second Zone (MULTISOURCE) pre-amp feed with assignable 12 V DC trigger control.
• Gold-surfaced connectors are employed throughout to ensure maximum signal integrity.
E.A.R.S., MA
TRIX AND DIGIT
AL SURROUND
MATRIX
DIGITAL
A key element of the T 753’s unique musical aptitude is NAD’s proprietary Enhanced Ambience Recovery
System (EARS). In sharp contrast to many “ambience-synthesis” music-surround modes, EARS exploits the
T 753’s substantial DSP power to route the ambient content that is “encrypted” in virtually all naturalacoustic recordings to the appropriate main, center and surround speakers, without resorting to artificially
generated reflections or regeneration. EARS’ natural ambience yields a subtle but exceptionally effective
surround mode that naturally enhances the spatial presentation in a fashion suitable for serious music
listening. The T 753 also incorporates a second proprietary surround mode, Matrix 7.1. This creates a full
6.1/7.1-channel environment from stereo and surround-encoded recordings, oftentimes with extraordinarily
good results. Dolby ProLogic II Music and DTS Neo:6 Music modes can also create enjoyable experience
from 2-channel sources.
On the digital side, the T 753 combines extraordinarily high-speed DSP processing employing one of the most
advanced high-speed DSP “engines” available, with fully 24-bit, 96 kHz-sampling-capable D/A converters
for all channels. A single, high-precision master clock synchronizes all digital circuits to eliminate the timing
errors (“jitter”) that otherwise compromise sonics. The result is legitimately state-of-the-art surround
decoding from Dolby Digital and DTS sources, and 6.1/7.1-channel reproduction, with genuinely superior
sound quality in all modes.
EASE OF USE
Despite the effort NAD has invested in the T 753 receiver’s sonic performance, we expended no less in
making it powerfully easy to use. Its design is uniquely simple for so sophisticated a component, and the HTR
2 universal remote control is equally understandable, as are the T 753’s own front-panel and on-screen
displays. Its simple yet powerful system of “presets” permits you to fine-tune your listening setup for
different conditions, sources, or listeners, and to recall these multiple parameters with a single keypress.
INTEGRA
TION
INTEGRATION
The T 753 receiver offers extensive, flexible system-integration options through its configurable DC trigger
outputs and input, and its standard-protocol IR communications links. The DC trigger outputs can be
assigned to either Local and/or Zone locations.
SECOND ZONE (MUL
TISOURCE)
(MULTISOURCE)
The T 753 receiver is equipped with a second Zone control of the Pre-amp level audio outputs from the
second Zone remote control ZR 2. Completes access to volume, On/Off, and all audio analog/digital inputs,
including the local input is available.
7
ABOUT THE T 753
UPGRADABILITY
The T 753 receiver permits flexible system growth via individually accessible pre-out and main-in jacks for all
three front channels, enabling external amplifiers to be used for any of these while still maintaining utility
of the receiver’s on-board power-amplifier channels for additional channels, remote-room links, or any other
suitable purpose. Of course, the T 753’s Surround Back channel outputs let a system grow from 6.1 to 7.1
channels, simply by adding a 1- or 2-channel external amplifier. See “Rear Panel (Audio Pre-Out)”.
ABOUT THE HTR 2 SYSTEM REMOTE CONTROL
Packed with your T 753 is the NAD HTR 2 remote control, a full-system remote especially designed to be easy
to use and easy to understand. Be sure to read the section “Using the HTR 2 Remote Control”, to familiarize
yourself with the remote’s layout and operations before proceeding to setup your A/V receiver.
Chances are, you will want to use your HTR 2 as your primary way to command your entire A-V system. The
HTR 2 can be employed to operate additional NAD or other-brand components such as a DVD/CD player,
television, satellite/HDTV tuner, VCR, or virtually anything else that operates via standard infrared remote
control.
8
QUICKSTART
In case you simply cannot wait to experience the performance of your new NAD T 753 receiver, we provide
the following “Quickstart” instructions to get you underway. The steps below connect your DVD player to the
T 753’s DVD input; be sure to read “Input Setup”, below.
PLA
Y A DVD MOVIE
PLAY
ENGLISH
• Connect the T 753’s composite video or S-Video MONITOR OUT jack to your TV/monitor’s corresponding
input. (Cables not supplied)
• Connect your DVD player’s composite video or S-Video output to the T 753’s corresponding DVD input.
(S-Video cable not supplied)
• Connect the DVD player’s optical digital output to the T 753’s optical DIGITAL IN 1 input.
(Optical cable not supplied).
• Connect your left and right front speakers to the T 753’s FRONT L and R outputs, being sure to connect
red to red (“+”) and black to black (“-”), with care to avoid stray wires or strands crossing between
terminals. (Connect center, surround, and surround-back speakers as well, if you like). If your system
includes a powered subwoofer, connect the T 753’s AUDIO PRE-OUT SW1, 2 or both jacks to its line
inputs.
• Press in the main power switch (black pushbutton) on the T 753’s rear panel (this puts the T 753 into
STANDBY mode and illuminates an amber LED to indicate it is ready to receive remote commands), then
use the HTR 2’s [ON] key to power up the receiver. Be sure the TV/monitor is powered up, with the correct
input selected.
• Start playback of the DVD player. Press the HTR 2 remote’s [Amp] Device Selector key, and then its (red)
DVD/numeric 1 key to select the DVD input. You should hear multichannel or stereo sound, and see an
image on the TV/monitor. (If one or the other fails to appear, you may need to use the receiver’s on-screen
menu system to check assignment of audio, video, and digital inputs; see “Setting Up the T 753”.)
Enjoy the movie or music, but be sure to set aside time to read this manual thoroughly, and to set up,
calibrate, and configure your T 753 carefully and completely.
9
FRONT PANEL
1
STANDBY SWITCH: Pressing this key, or the HTR 2 remote’s [ON] button, will switch the receiver on, making it operational, changing the amber
Standby indicator to green and illuminating the VFL display.
2
STANDBY LED: Illuminates amber when the T 753 is in Standby mode; green when it is powered on; and flashes momentarily to indicate infrared
commands received from the HTR 2 remote. Protection Mode is indicated by a red illumination, and indicates that there is a problem with your setup or the unit itself. When the fault is removed, normal operation can be resumed (this may require turning the unit off and on again). This indicator
will be steadily dark only when the main POWER switch (REAR PANEL No.9) is switched off (or the receiver is unplugged from the AC supply).
3
AM/FM: Press to toggle between the tuner’s AM and FM bands.
4
FM MUTE/MODE: In the normal Mute position, only the stations with a strong signal can be listened to, and the noise between stations is muted.
Pressing the [FM Mute/Mode] button allows distant (and potentially noisy) stations to be received. (See “Listening to Radio”)
5
DISPLAY: Press to display the channel mode of the currently selected source (other than the internal AM/FM tuner), in the format “front/rear/LFE.”
For example, a Dolby Digital or DTS 5.1-channel source will display 3/2.1. Note that the display shows signal channels, not speakers; for example,
a 2-channel analog or digital source (whether stereo or surround-encoded) will show 2/0.0, even though the receiver’s may
indeed be set up to use the subwoofer with all sources, and the current Listening Mode may employ center and surround speakers.
When the AM/FM tuner is the selected input, sequentially pressing DISPLAY shows the currently tuned station’s RDS data, toggling between the
current station’s Radio Text and Station Name displays (see Listening to Radio, below).
6
MEMORY: Use to store tuned stations to the T 753’s 40 preset-memory locations. (see Listening to Radio, below)
7
PRESET: Press to step up or down between radio presets; 30 FM and 10 AM station presets are available. Note that this function “wraps”:
Pressingwill step from Preset 30 to Preset 1, or vice versa using thekey. “Unused” presets are skipped over. (Note that Presets must previously
have been stored; see “Listening to Radio,” below.)
8
SEARCH : Press momentarily to step up or down between FM or AM frequencies. Press and hold SEARCHfor more than 2 seconds to
search up or down; the T 753’s tuner will stop at the next sufficiently strong signal it encounters. Note that this function, too, “wraps,” and will
continue searching up or down from one end of the AM or FM band to the other.
Note that: SEARCH tunes the FM band by 0.05 MHz steps (twice the precision of most tuners and receivers). On the AM band, SEARCH
moves by 10 kHz or 9 kHz steps. To change the step amount, hold in the FM MUTE/MODE and AM/FM keys simultaneously.
9
VFL DISPLAY: The Vacuum Fluorescent Display provides visual information on all of the T 753’s important modes, settings, and functions for both
MAIN and second ZONE locations.
10 VOLUME (SETUP): Turn clockwise to increase the master-volume setting; counterclockwise to lower it. The VFL and on-screen displays show the
setting, displayed in decibels between –74 and +18.
The VOLUME (SETUP) knob is also used to increment/decrement individual channel levels and other adjustable parameters.
10
FRONT PANEL
11 SOURCE: Use to select one of six inputs. Press repeatedly to step through the T 753’s audio/video inputs. The digital inputs are default
assigned to the video input (DVD, SAT, VCR, VIDEO 4-5, CD) but can be arranged in any order using the T753’s SETUP OSD. The chart below shows
the default assignments; see “Input Setup.”
Default Assignment
DVD
SAT
VCR
VIDEO 4
VIDEO 5
CD
ENGLISH
Digital Input Jack
OPT 1
OPT 2
Coax 3
Coax 4
Coax 5
Coax 6
NOTE: Digital inputs take precedence: The T 753 will automatically play any active signal present at the selected digital input; if none is present,
it will “fall back” to the analog audio input assigned to that Video input. Digital inputs can be selected OFF to listen to the analog input of a source
with an assigned digital input.
12 SURROUND MODE: Use to select the T 753’s Listening Mode. Press repeatedly to step through the T 753’s Listening Modes. See “About the T 753’s
Listening Modes,” below.
NOTE: Depending on the format of the currently selected input (digital or analog; stereo or multichannel), different modes will be available. See
“About the T 753’s Listening Modes,” below.
13 LEVELS: Press repeatedly to select the channel, and then use the VOLUME(SETUP) knob to adjust the levels of the T 753’s 7 channels /pairs in turn:
front-left, -center, –right; surround; surround back; subwoofer. The selected channel appears on the VFL and on-screen displays; use the
VOLUME(SETUP) knob to adjust its level relative to the others over a range of ±12 dB. Channel levels may also be adjusted via the on-screen menus;
see “Adjusting Channel Levels,” below.
NOTE: The HTR 2 remote’s [Surr.], [Center], and [Sub]/ keys provide direct access to those channels’ relative levels, however in this case the
level changes are only temporary and are not saved in memory.
14 TONE DEFEAT: Press to disable the tone controls; press again to re-enable them for instance, to compare a tone setting to unmodified sound.
NOTE: While TONE DEFEAT is engaged, the TONE CONTROLS key will have no effect.
15 TONE CONTROLS: Press to adjust treble using the VOLUME (SETUP) knob over a ±10 dB range; press again to adjust bass, and a third time to exit
tone-control adjustment.
16 SPEAKERS A & B: Press either speaker A or B or both to select the set of speakers you wish to listen to. The Speakers A are the main set of 6 multichannel front and surround speakers. The Speaker B are an auxiliary set for remote locations such as other rooms of your home. For Speaker B
selection all surround sound sources are downmixed to stereo as shown in the florescent display.
17 VIDEO 6 INPUT: Use these convenience jacks for occasional sources, such as a camcorder, portable MP3 or tape player, or a video game console,
or any other analog audio, or composite or S-Video video source. Select the Video 6 input using the HTR 2 remote, or the front-panel VIDEO 6 key.
18 PHONES: Accepts stereo headphone using a standard 1/4-inch stereo phone plug (use a suitable adapter for headphones equipped with a smaller
plug); set the Listening Mode to “Stereo.”
NOTE: For headphone listening the front left/right speakers must be set to “Large” on the OSD’s Speaker Settings page, otherwise headphone bass
response will be restricted.
NOTE: Plugging in headphones will automatically switch the T 753 to “Stereo” mode.
11
REAR PANEL
2
3
4
6
5
7
8
T 753 (AH) NORTH AMERICA
1
Serial No./No. De Series
17
POWER
ON
OFF
MS OUT
+12V TRIGGER
16
15
14
13
12
11
10
9
AC OUTLET
230V ~50HZ 120W 1A MAX
T 753 (C) EUROPEAN VERSION
ATTENTION!
Please make all connections to your T 753 receiver with the unit powered off or unplugged. (It is also advisable to power-down or unplug all
associated components while making or breaking any signal or AC power connections.)
1
FM & AM ANTENNA: The supplied wire “dipole” FM antenna will connect to the FM connector using the supplied “balun” adapter. It will usually
work best when mounted on a vertical surface such as a wall, with arms fully outstretched forming a horizontal “T” perpendicular to the origin point
of the signal. Experiment with placement and orientation of to yield the clearest sound and lowest background noise. In areas of difficult FM
reception an external FM antenna can yield dramatic gains in quality; consult your NAD audio specialist or a professional antenna installer.
The AM loop antenna supplied with the T 753 (or a suitable replacement) is required for AM reception. Open the clip terminal lever, insert the wire
and close, ensuring that the lever locks the wire in place. Testing different positions for the antenna may improve reception; vertical orientation will
usually produce the best results. Antenna proximity to large metal objects (appliances; radiators) may impair reception, as will attempts to lengthen
the wire to the loop.
NOTE: An external AM antenna can improve long-distance reception substantially; consult your NAD audio specialist or a professional antenna
installer. Do not connect anything other than a loop antenna to the AM ANTENNA terminal. Do not remove the AM loop antenna.
2
SOFT CLIPPING: Enables NAD’s proprietary Soft Clipping circuitry on all channels. Soft Clipping gently limits the output of the T 753 to minimize
audible distortion, even should the receiver be over-driven.
NOTE: Soft Clipping may simply be left on at all times to reduce the likelihood of audible distortion from excessive volume settings. However, for
critical listening, to preserve optimum dynamics you may wish to defeat it by setting this switch off.
3
MONITOR OUT: Connect to video input of the monitor/television, using quality dual-RCA and/or S-Video cables designed for video signals. In general,
the S-Video connection is superior and should be used if your TV/monitor provides the corresponding input.
NOTE: The T 753 “transcodes” S-Video to composite-video signals, so that S-Video signals connected to the DVD, SAT, VCR, and VIDEO 4-6 inputs
will be present at both the S-Video and composite MONITOR OUT jacks when any of these inputs is selected. This provides the convenience of
requiring only a single video connection (usually S-Video) between the T 753 and the TV/monitor.
4
CD: Connect the analog stereo audio output from a CD player or other line-level audio source to this input.
5
IR: These mini-jacks accept and output remote-control codes in electrical format, using industry-standard protocols, for use with “IR-repeater” and
multi-room systems and related technologies. Consult your NAD audio specialist for more information.
6
+12V TRIGGER IN/OUT:
TRIGGER IN connects to the 12-volt trigger outputs of compatible components such as power controllers and home automation devices. The TRIGGER
AUTO/OFF switch selects the 12V Trigger Input and disables the remote and front panel ON function.
TRIGGER OUT connects to 12V Input of compatible devices (such as amplifiers and projector-lifts) to automate turn on/off or activation. See “Trigger
Setup”, your NAD audio specialist also can provide more information on using the T 753’s triggers.
AUTO TRIGGER SWITCH when in the AUTO position, forces the T 753 to turn on only when a trigger signal is present at the trigger input. When in
the OFF position, the trigger inputs are disabled.
7
12
COMPONENT VIDEO IN 1-2; OUT: Connect the COMPONENT VIDEO IN 1, and 2 inputs to component-video outputs from compatible source
components, typically a DVD player and terrestrial or satellite HDTV tuner. Connect the T 753 COMPONENT VIDEO OUT to the component-video input
of a compatible video monitor/TV. Be sure to observe consistency in connecting the Y/Cr/Cb jacks (some source and TV components label these Y/
Pb/Pr) to the corresponding sources/inputs; do not rely purely on the colour-coding of the jacks, which may not always be consistent among brands.
The routing of the component-video inputs follows the S-Video/composite, but is default as: COMPONENT VIDEO IN 1 is routed to the COMPONENT
VIDEO OUT jacks when the DVD input is selected; COMPONENT VIDEO IN 2 is selected when the SAT input is active; the audio and digital inputs
assigned to DVD, and SAT will be used (see also, "Input Setup”).
REAR PANEL
NOTE: The T 753’s component-video inputs and outputs are fully wide-band, compatible with all HDTV formats. The T 753 does not display its
on-screen menus on its component-video output. To use on-screen menus, you will need to make an S-Video or composite connection between
the T 753 and the monitor/TV, and select it for menu display.
DIGITAL IN OPT 1-2; COAX 3-6: Connect to the coaxial S/PDIF-format digital outputs of sources such as CD or DVD players, HDTV or satellite
tuners, or other components; connect DIGITAL IN OPT1-2 to optical S/PDIF-format digital outputs.
DIGITAL OUT: Connect the optical and/or coaxial DIGITAL OUT ports to the corresponding S/PDIF digital input of a recording component such as
a CD recorder, DAT deck, or computer soundcard. See "Setting Up the T 753".
9
POWER: Press in to switch the A/V Receiver to standby mode. Pressing POWER again turns the unit OFF, recommended if you do not plan to use
your A/V Receiver for an extended period of time. It is usual (and perfectly acceptable) to leave the T 753 in Standby mode in between normal
viewing and listening sessions.
10 SWITCHED AC OUTLET: This convenience jack can supply switched power to another component or accessory. It is powered on and off by the
front panel POWER SWITCH (or the HTR2’s [On] and [Off] keys).
NOTE: The total draw of all devices connected to this jack must not exceed 120 watts.
11 AC POWER INLET: Connect to the supplied IEC-standard removable AC power cord or a compatible cord.
12 SPEAKERS A & B: Connect the left and right front, centre, left and right surround, and surround back speaker outputs to the corresponding
loudspeakers. Each output’s “+” (red) terminal and “-“ (black) terminal must be connected to the corresponding “+” and “-“ terminals of the
loudspeaker. Use extra care to ensure that no stray wires or strands cross between posts or terminals at either end.
Connect Speakers B left and right speaker outputs to the corresponding remote loudspeakers. When speakers B are activated the output is taken
from the front left and right channels and any signal source is converted “downmixed” to stereo as indicated in the florescent display.
NOTE: Use stranded wire of at least 16 gauge (AWG); specialized speaker cable may be valuable (consult your NAD audio specialist). Connections
to the T 753 can be made with banana plugs (US model only), or using bare wire, or pins, by loosening the terminal’s plastic nut, making a clean,
neat connection, and re-tightening carefully (use the transverse hole through the post for bare-wire or pin connections). To minimize the danger
of short-circuits, ensure that only 1/2-inch of exposed wire or pin is employed in connecting.
NOTE: This unit is designed to produce optimum sound quality when connected to speakers with impedances within the receiver’s operating
range. Please check front, center, and surround speakers are rated to be 4Ω min. per speaker.
IMPORTANT NOTE: For optimum surround performance, the T 753 speaker settings and levels must be set correctly via the receiver’s setup
routines; see “Setting Up the T 753”.
13 DVD, SAT, VCR, VIDEO 4, VIDEO 5: These comprise the T 753’s principal inputs. Connect S-Video, composite video, and analog stereo audio from
source components such as DVD players and HDTV/satellite tuners (see "Input Setup," below). VCR and VIDEO 4 may be used with recording
components such as videocassette or DVD-recorders; connect the T 753 S-Video/composite video OUT jacks to these components’ record-inputs.
(Note that VCR/VIDEO 4 may freely be used for play-only components, in which case their OUT jacks would remain unconnected.)
14 MAIN IN/AUDIO PRE-OUTS/SUBWOOFER OUT: The T 753’s six built-in power amplifier channels will deliver excellent quality with even very
demanding, low sensitivity home-theatre speaker systems. However, it is also possible to use the T 753 as a pre-amplifier with external power
amplifiers for some or all channels (remove the supplied jumpers) if necessary. Unlike the six full range channels, there is no power amplifier builtinto the T 753 for a subwoofer.
Connect the SW output 1, 2 or both to powered (“active”) subwoofers (or to power amplifier channels driving a passive system).
SURR-BACK-R jack will supply the same signal from the surround-back Left channel if the T 753 is so configured (see “Speaker Setup,” below).
Either one or both channels are available mono or stereo as per “Speaker Setup”. Connect to one or two channels of an appropriate external
power amplifier or other amplified component to furnish amplification for one or two surround back speakers. Your NAD audio specialist will be
happy to advise you.
NOTE: Never connect the T 753’s speaker outputs and the speaker outputs of an external amplifier to the same speakers.
15 TAPE IN/OUT: Connect the T 753’s TAPE OUT jacks to the stereo analog audio inputs, of an audio recording component such as a cassette deck
or CD recorder, or of an outboard analog audio processor such as a stereo equalizer; connect the receiver’s TAPE IN jacks to the component’s
corresponding outputs.
NOTE: Digital input signals are not available at the analog TAPE OUT jacks.
16 MS OUT (MULTISOURCE OUT): Connect this pre-amp outputs to other zones using high-quality patch cables to reduce noise pickup over long
distance runs.
17 7.1 CH. INPUT: Connect to the corresponding analog audio outputs of a multichannel source component such as a DVD-Audio or multichannelSACD player, or external multichannel decoder. Typically, these sources will produce 5.1-channel output, in which case the SURROUND BACK jacks
are left unconnected. The signals present at these jacks may be heard by selecting the front-panel EXT. 7.1 key or the HTR 2’s [Ext 7.1/5.1]
button. See “Selecting Sources".
NOTE: There is no bass-management or other processing (other than master-volume control) available to this 7.1 CH. INPUT. While the multichannel audio outputs of a DVD-Video player can be connected to these jacks, using the T 753’s own Dolby Digital and DTS decoding and digitalanalog converters, via a digital connection, will usually produce superior results.
13
ENGLISH
8
SETTING UP THE T 753
GETTING ST
AR
TED
STAR
ARTED
Before you make the first connection to your T 753, you should have the arrangement of your listening room/
home theater components and furniture mapped out, at least initially. Unfortunately, a discussion of the vital
questions of loudspeaker placement and listening/viewing positions is beyond our scope here. Suffice it to
say that these two questions will influence your system's ultimate performance every bit as powerfully as
your selection of electronics and speakers. Your NAD audio specialist dealer will be happy to advise you, and
to recommend reference materials.
NOTE: You will need the HTR 2 remote handset to configure your T 753. See “Using the HTR 2 Remote”,
below.
DEALING WITH HUM AND NOISE
Hum and noise sometimes prove a challenge in complex, multichannel audio systems. Note these considerations to help prevent hum and noise problems:
• Power all your system's audio component from AC outlets originating from the same circuit of your house
wiring. As far as possible, power all audio components from the same outlet, or adjacent outlets on the
same circuit. It may be useful to power video displays (and computers!) from outlets on another circuit,
especially if that circuit is supplied from the other "leg" of the house wiring.
• Do not bundle analog audio cables with AC power cables, or with coaxial digital-audio cables. It is best
if they cross at right angles if they must be in close proximity.
• Employ high-quality, well-shielded audio cable throughout, and ensure that all connections are secure.
• A pencil-eraser can be used to burnish copper- and gold-plated contacts to ensure good, low-resistance
contact; specialized contact-cleaners can also be useful. Avoid unnecessary unplugging and re-plugging,
since the gold (or copper) contact plating of typical cable connectors, even very high-quality ones, is very
thin and easily worn.
Track down hum/noise problems one component at a time, working backwards from the receiver. That is:
Connect the speakers to the receiver only, and check for hum. Then connect one component only (a CD
player, for example) alone, with no other components connected and check for hum. Connect additional
components, one at a time, to the receiver and check for hum. At each stage, if hum/noise appears,
examine the audio cabling and AC-power routing of the new component. In some cases, moving the new
component's AC cord to a different outlet, or installing a ground-lift (3-to-2-prong adapter) on its power
cord, will eliminate the hum.
14
ABOUT THE ON-SCREEN DISPLAYS (OSD) AND FRONT-PANEL READOUT
The T 753 receiver employs a simple, self-explanatory system of on-screen display "menus" that will appear
on the connected video monitor/TV. These are required during the setup process (and are useful in day-today operation), so be sure to connect the monitor/TV before proceeding with setup.
ENGLISH
NOTE: The on-screen displays are carried on both the S-Video and composite MONITOR OUT jacks, but are
not incorporated into the component-video output.
DISPLA
Y THE OSD
DISPLAY
Press any of the HTR 2 remote's central cursor keys ([], [], [], [], and [Enter]) to display the T
753’s main menu on your video monitor/TV. If the OSD does not appear, check your MONITOR OUT
connections.
NOTE: The OSD does not appear on the T 753's component-video output, nor does it appear on the VIDEO
3 and 4 record-outputs; these are for recording, not monitoring.
NA
VIGA
TING THE OSD AND MAKING CHANGES
NAVIGA
VIGATING
Use the HTR 2 remote's [/] keys to move up or down among the Setup menu's list of items; use [Enter]
to select a menu item, and use [/] to change the parameter-value (setting) of any item. Selecting the
returns "up" to the menu while saving any parameter-value changes to the T 753’s
memory; selecting also returns to the main menu, but abandons any
changes made on the previous menu. Selecting from the main Setup menu exits the OSD altogether,
retaining parameter-value changes, if any, made previously.
INPUT SETUP
The T 753 is equipped with nine configurable and nameable inputs: six audio-video inputs labeled DVD, SAT,
VCR, and VIDEO 4-6 (including VIDEO 6 on the front panel), and two audio-only inputs labeled CD and EXT
7.1. These are flexibly configurable and nameable: For each labeled video input-jack position (DVD, SAT,
VCR, VIDEO 4-6) as displayed on the
Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.5
Linearized : Yes
Page Count : 32
XMP Toolkit : XMP toolkit 2.9.1-14, framework 1.6
About : uuid:c5cb91a4-6bcf-11d9-9998-000393193046
Producer : Acrobat Distiller 5.0 (Windows)
Keywords :
Create Date : 2003:10:28 09:32:41Z
Modify Date : 2005:01:21 12:13:30-05:00
Metadata Date : 2005:01:21 12:13:30-05:00
Creator Tool : Adobe PageMaker 6.5
Document ID : uuid:85b2a414-433c-4c8d-ab7a-e978dabaec80
Format : application/pdf
Creator : danny.wong
Title : T762-OM-GB
Description : T762-OM-GB
Author : danny.wong
Subject : T762-OM-GB
.