National Datacomm SFA110S01 User Manual 8
National Datacomm Corporation 8
8
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 71084 |
| Application ID | O+PW9QnRGV8JMu60ZH3c/g== |
| Document Description | 8 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 27.2kB (339943 bits) |
| Date Submitted | 1999-11-19 00:00:00 |
| Date Available | 1998-09-16 00:00:00 |
| Creation Date | 2001-05-16 05:59:59 |
| Producing Software | Acrobat Distiller 4.0 for Windows |
| Document Lastmod | 2001-05-16 06:00:00 |
| Document Title | 8 |
NEUTRON EMC LAB. t FCC lD:IOUSFA1 16861 Attachment User’s Manual __———-————21/21———-—-—-—-———-—- PIug-n-Link ' Auto 10/100 PCI Fast Ethernet Adapter NFE100TA Installation Guide PIN. :85-500100—50 RevisionzAl February 1998 J. _.______._.~AA‘_A NDC Communications, Inc. 265 Santa Ana Court, Sunnyvale CA 94086, USA Tel: +1 (408) 730—0888 Fax: +1 (408) 730-0889 Technical Support Email: suppon@ndc1anccom NDC World Wide Web www.ndclan.com TRADEMARKS NDC is a trademark of NDC Communications, Inc. All other names mentioned in this document are trademarks/registered trademarks of their respective owners. FCC WARNING This equipment has been tested and found to comply with the limits for a Class B Digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However. there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV teclmician for help. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2. This device must accept any interference received, including interference that may cause undesired operation. Table of Contents INTRODUCTION ................. Hardware Description . Features ................. INSTALLATION .......... Hardware Installation. Driver Installativn.... TROUBLESHOOTING ..... LED: .................................. TECHNICAL SPECIFICATIONS Packing List The package should contain the following items: 0 One Auto 10/100 PCI Fast Ethernet Adapter 0 One 3.5 inch Diskette containing: Device drivers for popular network operating systems — Driver support files - A Diagnostic program 0 This Installation Guide Introduction Hardware Description The NDC NFEIOOTA Auto 10/100 PCI Fast Ethernet Adapter supports auto- detection/negotiation of 10/ lOOMbps data transmission speeds and offers a full-duplex function allowing 200me1». When connected to a lOBase-T Hub the adapter functions as a lOMbps Ethernet adapter. [f connected to a lOOBase-TX Fast Ethernet hub the adapter will function at lOOMbps. On a switching hub that supports full-duplex, the speed will be doubled to 20Mbps/200Mbps, The adapter is a PCI (Peripheral Component Interconnect) Local Bus adapter. Just plug in the card and hardware setup is done automatically. Four LED indicators proxide convenient analysis of network and adapter functions.” The NFEIOOTA is supplied with drivers for all popular network operating systems including: ODI Driver for NetWare 3.1x, 4.x, NDIS driver for Microsoft LAN Manager and Windows 95, Windows NT. SCO UNIX, and a Packet Driver. Features ./ Complies with IEEE 802.3 CSMA/CD, IOBase-T and lOOBase-TX standards / 32-bit PCI Local Bus Master for high performance and low CPU utilimtion / Full-duplex doubles performance to 20Mbps/200Mbps / Single STP connector for lOOMbps and lOMbps networks / Auto-detects/negotiates network speed / Four color-coded status LEDs indicate network link/activity and lO/lOOMbps selection / Supports smart remote boot ROM 1 Diagnostic software, network driver installation utility, and network drivers on the diskette lnstallation Hardware Installation Carry out the following steps to install the NFElOOTA Auto 10/ 100 PCI Fast Ethernet Adapter: 1. Turn off the computer and all peripherals 2. Make a note of the cables and cords that are connected to the computer and disconnect them 3. Remove the computer’s cover 4. Select any available PCI slot and remove the slot cover (the slot used should support bus mastering) 5. Carefully install the adapter into the expansion slot by firmly pressing the card into the slot until the adapter is snugly seated. Fasten the retaining bracket with the screw from the slot cover 6. Replace the computer's cover and reconnect the previously disconnected cables 7. Plug one end of the twisted-pair cable into the RJ-45 connector on the adapter and the other into a 10 or lOOMbps Ethernet hub or switch 8, Reconnect the power supply Driver Installation Before you can connect the NFEIOOTA Auto PCI Fast Ethernet Adapter to the network you have to install the network driver. You should use the network driver supplied on the software diskette that is compatible with your Network Operating System. A RELEASETXT file under the root directory lists information on all the available network drivers The network driver for each Network Operating System is under a separate directory. Each directory includes a READMETXT file which describes the installation procedure. The same driver functions on both 10Mbps and lOOMbps networks Troubleshooting If you experience any problems with the adapter, first make sure the correct driver is loaded, the proper cable is connected to the adapter port. and the hub complies with the adapter specification (lOBase-T or lOOBase-TX). Then check the LEDs. LEDs The LEDs provide “at-a-glance" network monitoring and are useful for diagnostic and installation purposes. The functions of the LEDs are: 0 LINK LED The LINK LED (green) indicates whether or not the adapter has made a link to the network. When the light is OFF the adapter is not connected to the network or the link is not OK. When the light is ON it indicates correct link integrity. 0 10/100Mbps LED The 10/100 LED (yellow) indicates whether the adapter is working under a lOMbps or IOOMbps environment. When the light is OFF the line speed is lOMbps. When the light is ON the line speed is lOOMbps. 0 RECEIVE LED The RK LED (green) indicates network data reception. When the light is OFF the adapter is not receiving data from the network. When the light is BLINKING data is being received. 0 TRANSlVIIT LED The TK LED (yellow) indicates network data transmission. When the light is OFF the adapter is not transmitting data to the network. When the light is BLlNKING data is being transmitted. ems/fr ._. - Technical Specifications Standards Compliance Electromagnetic Standards Cnmpliance Transmission Rate Bus Supported Connection Interface LED Indicators U0 address IRQ Line Cable Sonwsre Support Power Consumptinn Dimensions Operating Temperature Humidity Warranty IEEE 800.3 lOBasc-T IEEE 802.3u lOOBase-TX PCI Local Bus Specification FCC Class B CE-Mark ENSSOZZ Class B (CISPR 22 Class B) lOMbps or ZOMbps lOOMbps or 200Mbps 32-bit PCI Bus Mastering Single ill-45 connector for both IOBase-T and lOOBase-TX Four LEDs indicate Link, lOMhps or lOOMbps operation. Data Tmnsmission, and Data Reception Assigned by system Assigned by system For lOBase-T: Category 3,4.5, UTP cable: 100m (328fi.) per segment maximum. For lOOBase-TX: Category 5, UTP cable: 100m (328th pet segment maximum ODI driver for NetWare 3.1x, 4.x. NDIS driver for Microsoft IAN manager and Windows 95, Windews NT. SCO UND(, and a Packet driver 5VI 540Ma 120mmx 80mm(4.72 in x 3.14 in.) 0 to 55° C (32 to 131° F) l0% w 90%. (non-condensing) Lifetime limited Warranty EC DECLARATION OF CONFORMITY For the following equipment: Product Name : Auto 10/100 PCI Fast Ethernet Adapter Model Number 1 NFEtOOTA Produced by: Manufacturer’s Name : NATIONAL DATACOMM CORPORATION Manufacturer’s Address : 2F, N0. 28, INDUSTRY EAST 9“ ROAD SCIENCE PARK. HSlN-CHU TAIWANI R.0.c. is hereby confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (89/ 336/ EEC). The NFEtOOTA meets or exceeds the following EMC standards: EN-50081-1 standard : EN 55022 Class B (CISFR 22 Class B) EN-50082-1 standard : IEC-1 000-4-2 IEC-1 0004-3 lEC-1 000-44 IEC-1 000-4-5 The manufacturer/importer is responsible for this declaration: Company Name : NDC (EUROPE) CO., LTD Company Address : 1, EARLSFORT CENTRE. HATCH STREET, DUBLIN 2. IRELAND Person authorized to make this declaration: Name : CHIN-TU WU Position/Title : MANAGING DIRECTOR - 2 if 0 7 Z// F6 In H; AV] I ) ff 1 I if ______—- Date Legal Signature A 4-“
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Create Date : 2001:05:16 05:59:59 Producer : Acrobat Distiller 4.0 for Windows Modify Date : 2001:05:16 06:00:00-04:00 Page Count : 9EXIF Metadata provided by EXIF.tools