National Instruments Network Device Ni Pxi 7811R Users Manual 323792a

NI PXI-7811R to the manual f075f6ef-9013-4d00-a876-e856b385af5b

: National-Instruments National-Instruments-Network-Device-Ni-Pxi-7811R-Users-Manual-493808 national-instruments-network-device-ni-pxi-7811r-users-manual-493808 national-instruments pdf

Open the PDF directly: View PDF .
Page Count: 8

Getting Started with the

NI PXI-7811R

This document explains how to set up the National Instruments PXI-7811R

device.

Introduction

The PXI-7811R is an R Series reconfigurable I/O (RIO) device with

160 digital I/O (DIO) lines.

Traditional digital I/O devices have a fixed functionality provided by an

application-specific integrated circuit (ASIC), but the PXI-7811R has a

field-programmable gate array (FPGA) that allows you to define device

functionality and timing.

You can use the LabVIEW FPGA Module to graphically design the

PXI-7811R timing and functionality without having to learn a low-level

programming language or a hardware description language (HDL)

traditionally used for FPGA design. With the LabVIEW FPGA Module,

you create or download a custom virtual instrument (VI) to the FPGA.

You can reconfigure the PXI-7811R device with a new VI at any time.

You can use the LabVIEW Real-Time Module to communicate and control

the PXI-7811R device while performing additional tasks, such as real-time

floating-point processing and data logging.

Note If you are using LabVIEW but not the LabVIEW FPGA Module, you can create VIs

that run in LabVIEW to control existing FPGA VIs, but you cannot create new FPGAVIs.

The PXI-7811R device has Flash memory that you can use to store VIs.

You can configure VIs to load to the FPGA and to run when the device

powers up.

Getting Started with the NI 7811R 2 ni.com

Required Items

This section provides lists of the items necessary for getting started using

the PXI-7811R with Windows 2000/XP and the LabVIEW Real-Time

Module.

Documentation

The NI PXI-7811R User Manual describes the electrical and mechanical

aspects of the PXI-7811R device and contains information about device

operation and programming. This document is included on the NI-RIO CD

and is also available at ni.com/manuals.

LabVIEW Help is available in LabVIEW by selecting Help»VI, Function,

& How-To Help.

Windows 2000/XP

Use the following items to set up and use the PXI-7811R with

Windows 2000/XP.

❑PXI-7811R device

❑The following software packages:

– LabVIEW 7.1 or later

– LabVIEW FPGA Module 1.1 or later—required to develop

custom FPGA VIs for the PXI-7811R device

– NI-RIO 1.1 or later—included with the PXI-7811R

❑PXI/CompactPCI chassis and a PXI/CompactPCI embedded

controller running Windows 2000/XP (or any computer running

Windows 2000/XP and a MXI-3 link to a PXI/CompactPCI chassis)

❑At least one cable and device for connecting signals to the PXI-7811R

LabVIEW Real-Time Module for ETS

Use the following items to set up and use the PXI-7811R with the

LabVIEW FPGA Module and the LabVIEW Real-Time Module.

❑PXI-7811R device

❑The following software packages:

– LabVIEW 7.1 or later

– LabVIEW Real-Time Module for ETS 7.1 or later

© National Instruments Corporation 3 Getting Started with the NI 7811R

– LabVIEW FPGA Module 1.1 or later—required to develop

custom FPGA VIs for the PXI-7811R device

– NI-RIO 1.1 or later—included with the PXI-7811R

❑PXI/CompactPCI chassis and real-time PXI controller

❑One of the following host computers, depending upon your

application, running Windows 2000/XP:

–PC

– Laptop computer

– PXI/CompactPCI embedded controller

❑At least one cable and device for connecting signals to the PXI-7811R

❑CAT 5 Ethernet crossover cable if the real-time PXI system is not

configured on a network. To connect the PXI system to a network port,

use a standard CAT 5 10/100Base-T Ethernet cable.

Installing Software

The following instructions describe how to install the NI-RIO device

drivers and LabVIEW.

Installing LabVIEW, the LabVIEW Real-Time Module for ETS, and the

LabVIEW FPGA Module

Use the following sequence when installing LabVIEW, the LabVIEW

Real-Time Module for ETS, and the LabVIEW FPGA Module. For more

detailed information about software requirements, refer to the LabVIEW

FPGA Release Notes.

If you are using NI-RIO without LabVIEW, skip these steps and complete

the steps in the Installing NI-RIO Device Drivers section.

Note You must install LabVIEW 7.0 or later and the LabVIEW modules you will be using

with the NI 7811R before installing the NI-RIO device drivers. For LabVIEW installation

instructions, refer to the LabVIEW Release Notes.

1. Install LabVIEW for Windows from the LabVIEW CD.

2. Install the LabVIEW Real-Time Module for ETS from the LabVIEW

Real-Time CD.

3. Install LabVIEW FPGA from the LabVIEW FPGA CD.

4. Install the NI-RIO device drivers. Refer to the Installing NI-RIO

Device Drivers section for driver installation instructions.

Getting Started with the NI 7811R 4 ni.com

Installing NI-RIO Device Drivers

Complete the following steps to install the NI-RIO device drivers that are

included with the PXI-7811R device. If you are using LabVIEW, complete

the installation instructions in the Installing LabVIEW, the LabVIEW

Real-Time Module for ETS, and the LabVIEW FPGA Module section

before installing the NI-RIO device drivers.

1. Run setup.exe from the NI-RIO CD and follow the setup

instructions.

2. Follow the onscreen instructions until the Feature Tree window

appears.

3. In the Feature Tree window, select the components to install. You must

install NI-VISA, NI-RIO, and NI Measurement & Automation

Explorer (MAX).

4. Follow the onscreen instructions to complete the driver installation.

5. Reboot your computer.

Installing Hardware

This section describes how to unpack and install the PXI-7811R device.

You can install the PXI-7811R in any available peripheral slot in the PXI

or CompactPCI chassis.

Note You must install the NI-RIO device drivers before installing the PXI-7811R device.

Unpacking

The PXI-7811R device ships in an antistatic package to prevent

electrostatic discharge from damaging device components. To prevent such

damage when handling the device, take the following precautions:

• Ground yourself using a grounding strap or by holding a grounded

object, such as your computer chassis.

• Touch the antistatic package to a metal part of the computer chassis

before removing the devices from the package.

Caution Never touch the exposed pins of connectors.

Remove the devices from the package and inspect the devices for loose

components or any other sign of damage. Notify NI if the devices appear

damaged in any way. Do not install damaged devices into the computer.

Store the PXI-7811R in the antistatic envelope when not in use.

© National Instruments Corporation 5 Getting Started with the NI 7811R

Installation

You can install the PXI-7811R in any available peripheral slot in the PXI

or CompactPCI chassis. Complete the following steps to install the

PXI-7811R device.

Note You must install the software before installing the hardware. For software

installation instructions, refer to the Installing Software section.

1. Power off and unplug the PXI or CompactPCI chassis.

2. Make sure there are no lit LEDs on the chassis. Wait for any lit LEDs

to go out before continuing the installation.

3. Remove the filler panel for the peripheral slot.

4. Ground yourself using a grounding strap or by touching a grounded

object, such as the PXI or CompactPCI chassis.

5. Insert the PXI-7811R into the slot. Use the injector/ejector handle to

fully inject the PXI-7811R into place.

6. Screw the front panel of the PXI-7811R to the front panel mounting

rails of the chassis.

7. Visually verify the installation. Make sure the PXI-7811R is not

touching other devices or components and that the PXI-7811R is

fully inserted into the slot.

8. Plug in and power on the PXI or CompactPCI chassis.

Connecting Signals

The PXI-7811R has four DIO connectors with 40 DIO lines per DIO

connector.

Figure 1 shows the I/O connector locations for the PXI-7811R. The

I/O connectors are numbered starting at zero.

Getting Started with the NI 7811R 6 ni.com

Figure 1. PXI-7811R Connector Locations

CONNECTOR 0 (DIO) CONNECTOR 1 (DIO)

CONNECTOR 3 (DIO) CONNECTOR 2 (DIO)

Reconfigurable I/O

NI PXI-7811R

© National Instruments Corporation 7 Getting Started with the NI 7811R

Figure 2 shows the pin assignments for all I/O connectors on the

PXI-7811R.

Figure 2. PXI-7811R I/O Connector Pin Assignments

Caution Connections that exceed any of the maximum ratings of input or output signals

on the PXI-7811R can damage the PXI-7811R and the computer. NI is not liable for any

damage resulting from such signal connections. Refer to the PXI-7811R User Manual for

the maximum input ratings for each signal.

For detailed information about connecting I/O signals, refer to the

NI 7811R User Manual.

Cabling Options

Accessing the signals on the I/O connectors requires at least one cable and

one signal accessory. Table 1 summarizes the National Instruments cables

available for use with the NI 7811R device.

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

DGND

+5V

+5V

DIO28

DIO30

DIO32

DIO34

DIO36

DIO38

DIO0

DIO2

DIO3

DIO5

DIO6

DIO7

DIO8

DIO1

DIO4

DIO9

DIO10

DIO11

DIO12

DIO13

DIO14

DIO15

DIO16

DIO17

DIO18

DIO19

DIO20

DIO21

DIO22

DIO23

DIO24

DIO25

DIO26

DIO27

DIO29

DIO31

DIO33

DIO35

DIO37

DIO39

135

236

337

438

539

640

741

842

943

10 44

11 45

12 46

13 47

14 48

15 49

16 50

17 51

18 52

19 53

20 54

21 55

22 56

23 57

24 58

25 59

26 60

27 61

28 62

29 63

30 64

31 65

32 66

33 67

34 68

CompactRIO™, LabVIEW™, MXI™, National Instruments™, NI™, ni.com™, and NI-VISA™ are

trademarks of National Instruments Corporation. Product and company names mentioned herein are

trademarks or trade names of their respective companies. For patents covering National Instruments

products, refer to the appropriate location: Help»Patents in your software, the patents.txt file on

your CD, or ni.com/patents.

© 2004 National Instruments Corp. All rights reserved.

323792A-01 Apr04

*323792A-01*

Documentation Resources

Refer to the following documentation for information about the

LabVIEW FPGA Module, R Series hardware, and VIs necessary for your

application.

•LabVIEW FPGA Module Release Notes—describes the software

installation and other known software issues

•LabVIEW FPGA Module User Manual—describes the LabVIEW

FPGA Module software and techniques for building applications in

LabVIEW with the LabVIEW FPGA Module

•PXI-7811R User Manual—describes the electrical and mechanical

aspects of the PXI-7811R device and contains information concerning

its operation and programming

•LabVIEW Help—describes the VIs and function reference information

•CompactRIO R Series Expansion System Installation

Instructions—describes how to install the CompactRIO R Series

Expansion chassis and CompactRIO I/O modules

Where to Go from Here

Refer to the LabVIEW FPGA Module Release Notes for information about

getting started with LabVIEW FPGA VIs and host VIs. This document also

provides examples for verifying that your software and hardware are

properly installed. To access this document, select Start»Programs»

National Instruments»LabVIEW»Module Documents.

Table 1. Cabling Options

Cable Description

SH68-C68-S For connecting signals from the DIO connector to the NI SCB-68 terminal

block.

NSC68-5050 For direct connection of the NI 7811R and SSR backplanes.

Routes signals to connectors that attach directly to SSR backplanes.