National Instruments Pci Serial And 485 4 Isolated Users Manual Using With Linux
PCI-4854 to the manual d75ad538-d51e-4fc6-9012-5df7ab7d152b
2015-02-05
: National-Instruments National-Instruments-Pci-Serial-And-Pci-485-4-Isolated-Users-Manual-493937 national-instruments-pci-serial-and-pci-485-4-isolated-users-manual-493937 national-instruments pdf
Open the PDF directly: View PDF 
.
Page Count: 19
| Download | |
| Open PDF In Browser | View PDF |
NOTE TO USERS USING PCI SERIAL WITH LINUX This document contains instructions to help you install and configure the National Instruments serial hardware for Linux. This document includes information about the PCI-232/2, PCI-232/4, PCI-232/8, PCI-485/2, PCI-485/4, PCI-485/8, PCI-232/2 Isolated, PCI-232/4 Isolated, PCI-485/2 Isolated, and PCI-485/4 Isolated interfaces. This document assumes that you are already familiar with Linux. Contents Related Documentation........................................................................... 2 Contributions ................................................................................... 2 Gather What You Need to Get Started.................................................... 2 Quick Start .............................................................................................. 4 Setup........................................................................................................ 5 Create Devices ................................................................................. 5 MAKEDEV Example ............................................................... 5 Find Interface Information............................................................... 5 Assign Serial Driver......................................................................... 6 setserial Example ...................................................................... 7 Assign Serial Drivers Using PCI-485....................................... 7 Assign Serial Drivers Using PCI Eight-Port Interfaces............ 7 Enable PCI Interrupt ........................................................................ 7 Configuration .......................................................................................... 8 View Your Hardware Resources ..................................................... 8 Enable FIFO Buffers........................................................................ 8 FIFO Example .......................................................................... 9 Configure struct termios .................................................................. 9 Configure PCI-485 .................................................................................. 10 Select Transceiver Mode ................................................................. 10 rs485 Example .......................................................................... 10 Lower Baud Rate Selection ............................................................. 10 Test the Setup.......................................................................................... 11 natinst.com™, National Instruments™, and NI-Serial ™ are trademarks of National Instruments Corporation. Product and company names mentioned herein are trademarks or trade names of their respective companies. 322539A-01 © Copyright 1999 National Instruments Corp. All rights reserved. August 1999 Troubleshooting and Common Questions ...............................................12 Error Codes.......................................................................................12 Common Questions ..........................................................................13 Assign Driver...........................................................................................15 Sample /etc/rc.d/rc.serial File ..................................................................17 Related Documentation The following documents contain information that you might find helpful as you read this document: • Linux Serial-Programming-HOWTO by Peter Baumann. You can find the latest version of this document at the following locations: ftp://metalab.unc.edu/pub/Linux/docs/HOWTO/Serial-P rogramming-HOWTO http://metalab.unc.edu/LDP/HOWTO/Serial-Programming -HOWTO.html • Linux Serial-HOWTO by David Lawyer. You can find the latest version of this document at the following locations: ftp://metalab.unc.edu/pub/Linux/docs/HOWTO/Serial-H OWTO http://metalab.unc.edu/LDP/HOWTO/Serial-HOWTO.html Contributions Thanks to Vern Howie for providing suggestions and examples from his serial suite. Also, thanks to David Lawyer, Greg Hankins, and Peter Baumann for providing so much information in their HOWTOs. Gather What You Need to Get Started Before you install your PCI serial interface for Linux, make sure you have the following: • Linux kernel version 2.2.3 or later. The product has been thoroughly tested with kernel version 2.2.3; however, the product might work with earlier kernel versions. If you do not have kernel version 2.2.3 or later, or if you do not have the following options already compiled into your kernel, you need to recompile you kernel. Include the following options when you configure and recompile the kernel using make menuconfig. Using PCI Serial with Linux 2 www.natinst.com a. b. • General Setup – PCI Support – PCI Quirks – Backward-compatible /proc/pci Character Devices – Standard/generic dumb serial support – Extended dumb serial driver options – Support more than four serial ports – Support for sharing serial interrupts setserial 2.14 or later. To find the version of setserial, enter the following: linux# setserial –V • PCI Utilities 1.10 or later. You can download PCI Utilities 1.10 from ftp://metalab.unc.edu/pub/Linux/hardware • PCI-SERIAL.tar.gz. You can download this file from the National Instruments FTP site at ftp://ftp.natinst.com/support/ ind_comm/serial/linux/ After you have the file, extract and unzip it by entering the following: linux# tar zxvf PCI-SERIAL.tar.gz The tar command extracts and unzips PCI-SERIAL.tar.gz and creates the sub-directory PCI-SERIAL. Enter the following to make sure all necessary files are included: linux# linux PCI-SERIAL# cd PCI-SERIAL ls FIFOtrigger intenable serialtest FIFOtrigger_pci.c interrupt_enable.c serialtest.c Clock_speed.c rs485 termios_program.c clockspeed rs485.c • Configure your BIOS to include a Plug and Play aware OS. • You need superuser privileges to do most of the steps and program segments in this document. © National Instruments Corporation 3 Using PCI Serial with Linux Quick Start This section is for experienced Linux users who are familiar with the lspci and setserial tools. If you are not familiar with either of these tools or if you require a detailed explanation of the steps, skip to the next section, Setup. 1. If you do not have enough available serial devices ( /dev/ttyS*) for each port on your multiport interface, create a new serial device by entering the following: linux# cd /dev linux /dev# ./MAKEDEV ttyS2. Find the port address, IRQ, and memory assignment of your PCI serial interface by enter the following: linux# lspci -v -n -d 1093:* 3. Assign the serial driver to your devices. Make sure you precede the port addresses with 0x. • For a PCI-232 interface, enter the following: linux# setserial /dev/ttyS uart 16550a port irq ^fourport • For a PCI-485 interface, which supports a higher baud_base of 460.8K at startup, enter the following: linux# setserial /dev/ttyS uart 16550a port irq baud_base 460800 ^fourport 4. Enable the PCI interrupt on your interface. To use intenable (from the PCI-SERIAL directory) to enable interrupts on your PCI serial interface, enter the following: linux PCI-SERIAL# ./intenable 5. If you have a PCI-485 interface, set the transceiver mode for each serial port. Refer to the section Select Transceiver Mode for more information about selecting a PCI-485 transceiver mode. 6. After you connect a cable between the two ports, test the setup by running serialtest (from the PCI-SERIAL directory). linux# Using PCI Serial with Linux ./serialtest 4 www.natinst.com Setup After you install the serial hardware (as shown in your PCI serial getting started manual), follow these steps to set up the interface. Create Devices Create a device for each port on your multiport interface. You only need to do this step once. Port address is the I/O address of the device, and port number is the device/serial port number of the port. Port number is used in the following context: ttyS . Since serial ports built into your computer are typically named from /dev/ttyS0 to /dev/ttyS3, the port number you choose needs to be four or greater. Enter the /dev directory, then use the MAKEDEV script to create a device for each serial port on the interface by entering the following. linux# cd /dev linux /dev# ./MAKEDEV ttyS MAKEDEV Example Enter the following to make the devices for a two-port interface: linux# cd /dev linux /dev# ./MAKEDEV ttyS4 linux /dev# ./MAKEDEV ttyS5 Find Interface Information Follow these instructions to find the port address, IRQ, and memory assignment of your PCI serial interface. Note Repeat this section each time you add another interface or physical device to the computer. Note This step may be done in normal user mode. 1. Use lspci (a command that displays information about the PCI bus) with the -v option (be verbose), the -n option (show PCI vendor and device codes as numbers), and the -d 1093:* option (display information only on devices with a National Instruments Vendor ID of 1093), to find the resource information of your serial interface. linux# lspci -v -n -d 1093:* Something similar to the following should appear. In this output, the IRQ is 11; the memory location is 0xdff80, and the port addresses are 0xdff0 and 0xdfe0. © National Instruments Corporation 5 Using PCI Serial with Linux 00:0a.0 Class ff00: 1093:d140 (rev 01) Flags: medium devsel, IRQ 11 Memory at 000dff80 (low-1M, non-prefetchable) I/O ports at dff0 I/O ports at dfe0 Write down the IRQ, memory location, and all the I/O port addresses for your computer. Note PCI Eight-Port Users—The PCI eight-port interfaces show only one I/O port address listing. The addresses of the other seven I/O ports are calculated by adding eight to the previous port address, (n × 8 + I/O port) for 0 < n < 8. The lspci call displays something similar to the following: 00:0a.0 Class ff00: 1093:d150 (rev 01) Flags: medium devsel, IRQ 11 Memory at 000dff80 (low-1M, non-prefetchable) I/O ports at df00 Assign Serial Driver Assign the serial driver to your devices. Note You need to repeat this step each time you restart your computer or until you set up your /etc/rc.d/rc.serial file. (Refer to the section Sample /etc/rc.d/rc.serial File for more information on setting up the /etc/rc.d/rc.serial file.) Enter the following to use setserial to tell the kernel each device’s UART, port address, and IRQ. Use information returned from the lspci output, and remember to precede the port address with 0x. linux# setserial /dev/ttyS uart 16550A port irq ^fourport Note The ^fourport flag is required regardless of how many ports you have on your interface. The ^fourport flag tells the serial driver that you are not using an AST four-port interface. Caution Using an invalid port can lock up your machine. setserial Example Enter the following to assign the serial driver to your devices for the values in the above two-port lscpi output: linux# Using PCI Serial with Linux setserial /dev/ttyS4 uart 16550A port 0xdff0 irq 11 ^fourport 6 www.natinst.com linux# setserial /dev/ttyS5 uart 16550A port 0xdfe0 irq 11 ^fourport Assign Serial Drivers Using PCI-485 Since the PCI-485 supports a higher baud_base of 460.8K at start-up, also enter the following at the linux prompt: linux# 460800 setserial /dev/ttyS baud_base For example, enter the following to assign the serial driver to /dev/ttyS4 for a PCI-485 serial port at port address 0xdfe0 and IRQ 11. linux# setserial /dev/ttyS4 uart 16550A port 0xdfe0 irq 11 ^fourport linux# setserial /dev/ttyS4 baud_base 460800 Assign Serial Drivers Using PCI Eight-Port Interfaces Enter the following to assign the serial driver to your devices for the PCI eight-port lspci output. Notice that the entries for port are consecutive and are separated by exactly 8 bytes. linux# setserial 11 ^fourport linux# setserial 11 ^fourport linux# setserial 11 ^fourport linux# setserial 11 ^fourport linux# setserial 11 ^fourport linux# setserial 11 ^fourport linux# setserial 11 ^fourport linux# setserial 11 ^fourport /dev/ttyS4 uart 16550A port 0xdf00 irq /dev/ttyS5 uart 16550A port 0xdf08 irq /dev/ttyS6 uart 16550A port 0xdf10 irq /dev/ttyS7 uart 16550A port 0xdf18 irq /dev/ttyS8 uart 16550A port 0xdf20 irq /dev/ttyS9 uart 16550A port 0xdf28 irq /dev/ttyS10 uart 16550A port 0xdf30 irq /dev/ttyS11 uart 16550A port 0xdf38 irq Enable PCI Interrupt To enable the PCI interrupt on your serial interface, use intenable, provided in the PCI-SERIAL directory. Run intenable each time you restart your computer. If you have more than one PCI serial interface, rerun intenable with another PCI memory address specified in the command line. Enter the following to use intenable: © National Instruments Corporation 7 Using PCI Serial with Linux linux PCI-SERIAL# ./intenable For example, enter the following to enable interrupts for a PCI serial interface with memory at 0x000dff80: linux PCI-SERIAL# ./intenable dff80 Configuration View Your Hardware Resources To see what system resources your serial interface is using, use the setserial command, as follows: linux# setserial -gv /dev/ttyS For the lspci and setserial examples, something similar to the following should appear: /dev/ttyS0, /dev/ttyS1, /dev/ttyS2, /dev/ttyS3, /dev/ttyS4, /dev/ttyS5, UART: UART: UART: UART: UART: UART: 16550A, Port: 0x03f8, IRQ: 4 unknown, Port: 0x02f8, IRQ: 3 unknown, Port: 0x03e8, IRQ: 4 unknown, Port: 0x02e8, IRQ: 3 16550A, Port: 0xdff0, IRQ: 11 16550A, Port: 0xdfe0, IRQ: 11 Enable FIFO Buffers Use FIFOtrigger (from the PCI-SERIAL directory) to enable the receive and transmit FIFOs and to set the trigger levels of these FIFOs. FIFOtrigger enables the FIFO of only one serial port. To enable the FIFO for your other serial ports, rerun FIFOtrigger with a different serial port number specified in the command line. Enter the following to use FIFOtrigger: linux PCI-SERIAL#./FIFOtrigger Using PCI Serial with Linux 8 www.natinst.com Table 1. tx_trigger Values Transmit FIFO Trigger Level tx_trigger 8 0x00 16 0x10 32 0x20 56 0x30 Table 2. rx_trigger Values Receive FIFO Trigger Level rx_trigger 8 0x00 16 0x40 56 0x80 60 0xC0 The hardware issues a transmit empty interrupt when the number of characters in the transmit FIFO falls below the trigger level. Also, the hardware issues a receive full interrupt when the number of characters in the receive FIFO rises above the trigger level. For more information on FIFO buffers, refer to your PCI serial getting started manual. FIFO Example Enter the following to set the receive FIFO trigger level to 56 and the transmit trigger level to 32 for /dev/ttyS5: linux PCI-SERIAL# ./FIFOtrigger 5 0x80 0x20 Configure struct termios Every serial port has an associated struct termios. By using this struct termios in a program, you can set the baud rate, character size (number of data bits), parity, control characters, flow control, and input and output mode. For more information about the termios structure, refer to the termios man page. To view the termios man page, enter the following: linux# man termios To configure your serial port, use a program segment similar to the termios_program.c in your PCI-SERIAL directory. © National Instruments Corporation 9 Using PCI Serial with Linux Configure PCI-485 If you are using a PCI-485 interface, you can select the transceiver mode for each device and select the lower baud rates listed in termios_program.c provided in your PCI-SERIAL directory. Select Transceiver Mode Use the rs485 program (from the PCI-SERIAL directory) to select the transceiver mode. rs485 sets the transceiver mode for only one serial port. To set the transceiver mode for other serial ports, rerun rs485 with a different serial port number specified in the command line. For more information on the transceiver control modes, refer to your serial getting started manual. If you do not know which transceiver mode to use, choose Four-Wire Mode. Table 3. Transceiver Mode Values Transceiver Mode Mode Four-Wire Mode 0 Two-Wire Mode: DTR with echo 1 Two-Wire Mode: DTR controlled 2 Two-Wire Mode: TXRDY auto control 3 Enter the following to use rs485: linux PCI-SERIAL# ./rs485 rs485 Example Enter the following to select Four-Wire Mode for /dev/ttyS5: linux PCI-SERIAL# ./rs485 5 0 Lower Baud Rate Selection To use a baud rate lower than 200, use setserial and the clockspeed program (from the PCI-SERIAL directory) to lower the baud base of a single serial port from 460800 to 115200. After changing the baud base to 115200, the max baud rate you can achieve is 115200 baud (until you change the baud base back to 460800). After you change the baud_base of the serial port using setserial and run the clockspeed program, you can use the lower baud rate flags in your programs. The clockspeed program changes the baud base of only Using PCI Serial with Linux 10 www.natinst.com one serial port. To change the baud base of your other serial ports, rerun clockspeed with a different serial port number specified in the command line. Enter the following to set the baud base. (In this example, high equals a baud base of 460800 and low equals a baud base of 115200): linux# setserial /dev/ttyS baud_base 115200 linux PCI-SERIAL#./clockspeed <"high" or "low"> For example, enter the following to select a baud base of 115200 for /dev/ttyS4 and for /dev/ttyS5: linux# setserial /dev/ttyS4 baud_base 115200 linux# setserial /dev/ttyS5 baud_base 115200 linux PCI-SERIAL# ./clockspeed 4 low linux PCI-SERIAL# ./clockspeed 5 low Enter the following to change the baud base back to 460800 for /dev/ttyS4 and for /dev/ttyS5: linux# setserial /dev/ttyS4 baud_base 460800 linux# setserial /dev/ttyS5 baud_base 460800 linux PCI-SERIAL# ./clockspeed 4 high linux PCI-SERIAL# ./clockspeed 5 high Test the Setup After you connect the cables to the port (as shown in your PCI serial getting started manual), run the serialtest program (from the PCI-SERIAL directory) to verify your setup. Make sure you specify two different ports for the serialtest program, as shown in the following: linux PCI-SERIAL# ./serialtest If the test is successful, it displays a SUCCESS message. If the test hangs, press to exit the program, and continue to the next section, Troubleshooting and Common Questions. To test /dev/ttyS4 and /dev/ttyS5, connect a cable between the two ports and enter the following: linux PCI-SERIAL# ./serialtest 4 5 © National Instruments Corporation 11 Using PCI Serial with Linux Troubleshooting and Common Questions Error Codes This section lists possible error codes and solutions. Error Code /dev/ttyS : no such file or directory Solution The /dev/ttyS does not exist in the /dev directory. Enter the following to create the device: linux# cd /dev linux /dev# ./MAKEDEV ttyS Error Code Couldn't change i/o privilege level: Operation not permitted Solution The program requires superuser privileges. Either exit and log in as root, or enter the following: linux$ su Password: linux# Error Code setserial: Cannot set serial info: Address already in use Solution Make sure you are entering the correct port address into setserial. Also, make sure you are entering 0x if you are specifying a hex number. linux# setserial /dev/ttyS uart 16550a port 0x irq ^fourport Error Code intenable: Can't open /dev/mem: Permission denied Solution The program requires superuser privileges. Either exit and log in as root, or enter the following: linux$ su Password: linux# ./intenable Using PCI Serial with Linux 12 www.natinst.com Error Code intenable: ERROR: Initial value of interrupt enable register not equal to 0xC0C Solution Make sure that you are providing the program with the correct memory address. Enter the following to check for the memory address: linux# lspci -v -n -d 1093:* 00:0a.0 Class ff00: 1093:d150 (rev 01) Flags: medium devsel, IRQ 11 Enter this address! -->Memory at 000dff80 (low-1M, non-prefetchable) I/O I/O I/O I/O ports ports ports ports at at at at dff0 dfe0 dfa8 dfa0 linux# ./intenable dff80 Error Code rs485: ERROR: Couldn't write to /dev/ttyS 's scratch register Solution Make sure the device was configured correctly in setserial. Enter the following: linux# setserial -gv /dev/ttyS /dev/ttyS4, UART: 16550A, Port: 0xdff0, IRQ: 11 If the port listing does not match the one found by lspci, reconfigure the device by entering the following: linux# setserial /dev/ttyS uart 16550a port irq ^fourport Common Questions What do I do if intenable does not work immediately or causes a segmentation fault? Enter the following to recompile interrupt_enable.c and rerun intenable. Also, the source code for intenable is available for editing and viewing at interrupt_enable.c provided in the PCI-SERIAL directory. linux PCI-SERIAL# gcc interrupt_enable.c -o intenable linux PCI-SERIAL# ./intenable © National Instruments Corporation 13 Using PCI Serial with Linux What do I do if FIFOtrigger does not work immediately or causes a segmentation fault? Enter the following to recompile FIFOtrigger_pci.c and rerun FIFOtrigger. Also, the source code for FIFOtrigger is available for editing and viewing at FIFOtrigger_pci.c provided in the PCI-SERIAL directory. linux PCI-SERIAL# gcc -O FIFOtrigger_pci.c -o FIFOtrigger linux PCI-SERIAL# ./FIFOtrigger What do I do if rs485 does not work immediately? Enter the following to recompile rs485.c. Also, the source code for rs485 is available for editing and viewing at rs385.c, provided in the PCI-SERIAL directory. linux PCI-SERIAL# gcc -O rs485.c -o rs485 What do I do if clockspeed does not work immediately or if it causes a segmentation fault? Enter the following to recompile clock_speed.c and rerun clockspeed. Also, the source code for clockspeed is available for editing and viewing at clock_speed.c, provided in the PCI-SERIAL directory. linux PCI-SERIAL# gcc -O clock_speed.c -o clockspeed linux PCI-SERIAL# ./clockspeed What do I do if serialtest does not work immediately or if it causes a segmentation fault? Enter the following to recompile serialtest.c and rerun serialtest. Also, the source code for serialtest is available for editing and viewing at serialtest.c, provided in the PCI-SERIAL directory. linux PCI-SERIAL# gcc serialtest.c -o serialtest linux PCI-SERIAL# ./serialtest What do I do if serialtest hangs? Make sure the interface is seated correctly and tighten the screw that holds the interface in place. Also, make sure the cables are attached to the correct ports. In some cases, serialtest hangs if the transceiver modes (PCI-485) are not set. Try setting both transmit and receive ports to transceiver mode 0 (Four-Wire Mode). Using PCI Serial with Linux 14 www.natinst.com linux# ./rs485 0 linux# ./rs485 0 linux# ./serialtest What do I do if my ports are not communicating correctly and print strange characters? Make sure the baud rate, character size, clock speed (if PCI-485) and parity are the same for both the receiver and transmitter. Also make sure the transceiver modes (PCI-485) have been selected for both transceivers. How can I use /dev/ttyS0, /dev/ttyS1, /dev/ttyS2, or /dev/ttyS3 as National Instruments serial ports? Check for available serial devices by entering the following: linux# setserial -gv /dev/ttyS* /dev/ttyS0, /dev/ttyS1, /dev/ttyS2, /dev/ttyS3, UART: UART: UART: UART: 16550A, Port: 0x03f8, IRQ: 4 unknown, Port: 0x02f8, IRQ: 3 unknown, Port: 0x03e8, IRQ: 4 unknown, Port: 0x02e8, IRQ: 3 Devices labeled with UART: unknown are available for use. To designate the available device when using setserial, enter the following: linux# setserial /dev/ttyS uart 16550a port 0x irq ^fourport Assign Driver Use these instructions to automatically assign the driver at startup using /etc/rc.d/rc.serial. You should not change the /etc/rc.d/rc.serial file until you have your serial interfaces installed and configured. If you add another device or interface to your computer, and your lspci output changes, make sure you also change /etc/rc.d/rc.serial. Depending on your Linux distribution, you might not have an /etc/rc.d/ directory. In this case, your rc.serial would be located under /etc/rc.serial. If you do not have /etc/rc.d/, replace the references to /etc/rc.d/ with /etc/. If you are using a Debian distribution, replace the references to /etc/rc.d/rc.serial with /etc/rc.boot/0setserial. © National Instruments Corporation 15 Using PCI Serial with Linux For more information about using setserial, refer to linux # more /usr/doc/setserial*/README. 1. Enter the following: linux# linux# a. cp /usr/doc/setserial*/rc.serial /etc/rc.d/ pico /etc/rc.d/rc.serial Make sure that SETSERIAL= points to the correct location. Check your /bin and /sbin directories, and change the SETSERIAL= line to say either SETSERIAL=/bin/setserial or SETSERIAL=/sbin/setserial b. Under AUTOMATIC CONFIGURATION, leave the following lines uncommented and delete or comment out (by adding a # to the beginning of the line) all the other lines in the section. (Depending on your version of setserial, ttyS might replace cua): AUTO_IRQ=auto_irq ${SETSERIAL} /dev/cua0 ${AUTO_IRQ} skip_test autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua1 ${AUTO_IRQ} skip_test autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua2 ${AUTO_IRQ} skip_test autoconfig ${STD_FLAGS} ${SETSERIAL} /dev/cua3 ${AUTO_IRQ} autoconfig ${STD_FLAGS} c. Under MANUAL CONFIGURATION, comment out or delete everything but the following lines. Change the lines concerning /dev/cua4-/dev/cua(4+n) (where n is the number of ports on the PCI serial interface) to the following: # These are the first set of # ${SETSERIAL} /dev/ttyS4 uart address> irq ^fourport ${SETSERIAL} /dev/ttyS5 uart address> irq ^fourport ${SETSERIAL} /dev/ttyS6 uart address> irq ^fourport ${SETSERIAL} /dev/ttyS7 uart address> irq ^fourport AST Fourport ports 16550A port
Source Exif Data:File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Encryption : Standard V1.2 (40-bit) User Access : Print, Copy, Annotate, Fill forms, Extract, Assemble, Print high-res Create Date : 1999:09:01 09:46:33 Producer : Acrobat Distiller 3.01 for Windows Creator : FrameMaker 5.5.6p145 Modify Date : 1999:09:01 16:44:31 Title : Using PCI Serial with Linux Subject : 322539A-01, August 1999 Author : Technical Publications Page Count : 19 Page Mode : UseOutlines Page Layout : SinglePageEXIF Metadata provided by EXIF.tools