Navico VHFRS35 MOBILE VHF MARINE TRANSCEIVER User Manual Installation Manual

Navico Auckland Limited MOBILE VHF MARINE TRANSCEIVER Installation Manual

Contents

Installation Manual

simrad-yachting.comENGLISHRS35 VHFHS35 handsetInstallation Instructions
Simrad - RS35 Installation Instructions2Simrad - RS35 Installation Instructions 3Copyright © 2013 NavicoAll rights reserved.Simrad® is a registered trademark of NavicoNo part of this manual may be copied, reproduced, republished, transmitted or distributed for any purpose, without prior written consent of Simrad Electronics. Any unauthorized commercial distribution of this manual is strictly prohibited.Simrad Electronics may find it necessary to change or end our policies, regulations, and special offers at any time. We reserve the right to do so without notice. All features and specifications subject to change without notice. All screens in this manual are simulated.For free owner’s manuals and the most current information on this product, its operation and accessories, visit our web site: www.simrad-yachting.comIMPORTANT SAFETY INFORMATION Please read carefully before installation and use.DANGERThis is the safety alert symbol. It is used to alert you to potential personal injury hazards, Obey all safety messages that follow this symbol to avoid possible injury or death. WARNING WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury.CAUTIONCAUTION used without the safety alert symbol indicates a po-tentially hazardous situation which, if not avoided, may result in property damage.Table of Contents1 Installation preparation ................................................................................61.1 Checklist.................................................................................................................................................61.2 Tools needed for installation ..........................................................................................................62 VHF installation ..............................................................................................72.1 Location requirements .....................................................................................................................72.2 LCD viewing angle .............................................................................................................................72.3 Choose an installation type ............................................................................................................72.3.1 Mounting bracket installation .................................................................................................... 82.3.2 Recessed installation .....................................................................................................................92.4 RS35 dimensions ............................................................................................................................. 102.5 Handset mic wall hanger .............................................................................................................. 113 VHF electrical installation ............................................................................123.1 Connect the radio ............................................................................................................................ 123.2 Wiring diagram - NMEA 2000 connections ............................................................................ 153.3 Wiring diagram - External speaker and hailer ....................................................................... 163.4 Wiring diagram - NMEA 0183 connections ............................................................................ 173.5 Installation diagram - HS35 Charger Cradle .......................................................................... 184 Setup your radio - Your user MMSI...............................................................20
MMSI and license information:You must obtain a user MMSI (Marine Mobile Service Identity) and enter it into your RS35 in order to use the DSC functions. Contact the appropriate authorities in your country. If you are unsure who to contact, consult your Simrad dealer.The user MMSI is a unique nine digit number, similar to a personal telephone number. It is used on marine transceivers that are capable of using DSC (Digital Select Calling).Depending upon your location, you may need a radio station license for the RS35. You may also need an individual operator’s license. Simrad recommends that you check the requirements of your national radio communications authorities before operating DSC functions. IMPORTANT: 1. DSC functions will not operate on the RS35 until your MMSI has been entered. Refer to DSC Setup section for details.2. The radio channels installed into this Simrad VHF radio may vary from country to country de-pending upon the model and government or national communications authority regulations.3. Navico recommends that you check the radio operating licensing requirements of your country before using this Simrad VHF radio. The operator is solely responsible for observing proper radio installation and usage practices.4. A DSC warning label is supplied with this Simrad VHF radio. To comply with FCC regulations, this label must be axed in a location that is clearly visible from the operating controls of this radio. Make sure that the chosen location is clean and dry before applying this label.5. This radio is designed to generate a digital maritime distress call to facilitate search and rescue. To be eective as a safety device, this radio must be used only within the geographic range of a shore-based VHF marine Channel 70 distress and safety watch system. The geographic range may vary but under normal conditions is approximately 20 nautical miles.RF Emissions notice: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environ-ment. This device’s antenna must be installed in accordance with provided instructions; and it must be operated with minimum 96 cm spacing between the antennas and all person’s body (excluding extremities of hands, wrist and feet) during operation. Further, this transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.DISCLAIMER: It is the owner’s sole responsibility to install and use the instrument and transducers in a manner that will not cause accidents, personal injury or property damage. The user of this product is solely responsible for observing safe boating practices.NAVICO HOLDING AS. AND ITS SUBSIDIARIES, BRANCHES AND AFFILIATES DISCLAIM ALL LIABILITY FOR ANY USE OF THIS PRODUCT IN A WAY THAT MAY CAUSE ACCIDENTS, DAMAGE OR THAT MAY VIOLATE THE LAW.Governing Language: This statement, any instruction manuals, user guides and other information relating to the product (Documentation) may be translated to, or has been translated from, another language (Translation). In the event of any conflict between any Translation of the Documentation, the English language version of the Documentation will be the official version of the Documentation.This manual represents the RS35 and HS35 as at the time of printing. Navico Holding AS. and its subsidiaries, branches and affiliates reserve the right to make changes to specifications without notice.Copyright © 2013 Navico Holding AS. Simrad© is a registered trademark of Navico Holding AS.FCC StatementNote: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a normal installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an output on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced technician for help. A shielded cable must be used when connecting a peripheral to the serial ports.Important safety informationSimrad - RS35 Installation Instructions4Simrad - RS35 Installation Instructions 5
Note: A VHF antenna is not provided by Simrad. Consult your Simrad dealer for advice if necessary.1.2 Tools needed for installationYou will need the following tools:• Power drill (or hand drill) and drill bits• Philips screwdriver• Spanner• Jig saw (for a recessed installation).• RS35 base station, with microphone attached• Dust cover• GPS connector cable• Speaker connector cable• Power supply cable (with 7 A fuseholder incorporated)• Spare 7 A fuse• Mounting bracket, with: - 4 self-tapping screws - 4 flat screws - 4 plain washers - 4 spring washers - 4 nuts - 2 mounting knobs• Handset mic wall hanger, with: - 2 self-tapping screws - 2 flat screws - 2 plain washers - 2 spring washers - 2 nuts• 2 M5 x 32 screws with 2 plain washers and 2 nuts (for a recessed installation)• Operation Manual• Installation Manual• Warranty Card• DSC Warning Label• Template for flush mounting option• Declaration of Conformity document (where applicable)1 Installation preparation1.1 ChecklistCheck that you have all the following items before starting the installation. Contact your dealer if an item is missing:2 VHF installation2.1 Location requirementsPlease check these before doing any cutting or drilling.Whichever installation method you choose, ensure that the chosen location:• Is at least 3’ (1 m) from the antenna• Allows easy connection to (at least) a 10 Amp fused 13.6 V DC electrical source and the antenna• Is at least 1.5’ (45 cm) from the compass to avoid creating magnetic deviation of the compass during radio operation • Has a suitable space close by for installing the microphone bulkhead mount• Provides easy access to the controls on the front panel • Provides reasonable access to the wiring at the back of the radio• Provides enough room to fix the DSC warning label.2.2 LCD viewing angleThe VHF has a large LCD screen with an optimum viewing angle of approx. +/-20 deg. Ensure the chosen location provides a suitable view of the display. Ideally, the user should be directly in front of the display or no more than +/-20 deg from the front of the display. Note: If unsure, temporarily power up the radio and check for a suitable location.2.3 Choose an installation typeThere are two ways to install the radio. You can choose:• Deckoroverheadmountingbracketinstallation.The reversible mounting gimbal is fixed to a suitable site and the radio is placed into it. The radio can be removed for storage and the viewing angle can be adjusted.• Indashorrecessedinstallation.The radio is recessed into a cavity cut into a bulkhead. The radio fixture is permanent and the viewing angle cannot be adjusted.20˚20˚20˚20˚SideTopSimrad - RS35 Installation Instructions6Simrad - RS35 Installation Instructions 7
2.3.1 Mounting bracket installation1. Hold the supplied mounting bracket at the chosen location and use a soft pencil to mark the 4 screw hole positions onto the mounting surface.2. Drill the 4 screw holes where marked. Drill completely through the mounting surface.Note: If you are drilling into fiberglass, use a small drill bit to drill pilot holes before drill-ing the screw holes.3. Use the flat screws, spring washers, plain washers, and nuts to attach the mounting bracket to the location site OR, if you cannot reach behind the mounting surface to attach the nuts, use the self-tapping screws instead of the flat screws.4. Slide the radio into the mounting bracket. 5. Insert the 2 mounting knobs through the holes and tighten them sufficiently to hold the radio at your preferred viewing angle. 6. You can adjust the viewing angle at any time. The viewing angle has a 20º tilt range.7. Now install the microphone wall hanger.2.3.2 Recessed installation1. Tape the supplied mounting template to the chosen location. Ensure that the template is smooth and taut.2. Drill the 2 screw holes where marked. Drill completely through the mounting surface.Note: If you are drilling into fiberglass, use a small drill bit to drill pilot holes before drill-ing the screw holes.3. Drill through the corners of the hatched area where marked, then cut out the hatched area to create a cavity in the mounting surface. (The dashed line shows the total area that will be covered by the radio fascia after installation). 4. Remove the mounting template and slide the radio into the cavity. 5. Working from the rear of the bulkhead, screw the radio firmly to the mounting surface using the 2 M5 x 32 screws with the plain washers and nuts. (The screws should not be visible from the front of the radio).6. Now install the microphone wall hanger. Simrad - RS35 Installation Instructions8Simrad - RS35 Installation Instructions 9
2.4 RS35 dimensions 2.5 Handset mic wall hanger1. Hold the handset mic wall hanger at the chosen location and use a soft pencil to mark the 2 screw hole positions onto the mounting surface.2. If the mounting surface is:• non-metallic, use the 2 self-tapping screws and 2 plain washers to attach the handset mic wall hanger to the mounting surface. • metallic, use the 2 flat screws, 2 spring washers and 2 nuts to attach the handset mic wall hanger to the mounting surface. 3. Hang the handset mic on the handset mic wall hanger.4. Now connect the radio. 0.96" (24.5 mm)0.47" (12 mm)1.16" (29.5 mm)Simrad - RS35 Installation Instructions10 Simrad - RS35 Installation Instructions 11
3 VHF electrical installation3.1 Connect the radioBoth NMEA 0183 and NMEA 2000 is supported by this radio. Use the GPS connector cable to connect NMEA 0183, or the N2K connector for NMEA 2000 connections.1 - VHF antennaA suitable radio antenna (not supplied) must be mounted and connected before you can operate the radio. Consult your Simrad dealer for advice, if necessary. Always mount the VHF antenna as high as possible and at least 37” (96 cm) from the base station.2 - NMEA 2000 (N2K) connectorThe radio can be connected to an NMEA 2000 network via the NMEA 2000 NETWORK con-nector on the rear of the radio by a complaint N2K cable (not supplied).Pin / Socket Wire color Function (NMEA 2000)1 Green Can-D, Drain wire, Shield2 Red Can-S, Power, +12 V DC 3 Black Can-C, Ground4 White Can-H, Data High5 Blue Can-L, Data Low3 - GPS Connector and cableNMEA0183 OUT (+)2 (Orange)NMEA0183 IN (+)5 (Yellow)NMEA0183 IN (-)4 (Green)RS422 OUT (-)3 (White)RS232 OUT7 (Blue)RS422 OUT (+)6 (Black)RS232 IN8 (Grey)GROUND (Shield)NMEA0183 OUT (-)1 (Bare wire)Line up the arrow on the GPS connector with the arrow on the GPS cable and plug together. The pin details are shown for information.Pin /Socket Wire colorGPS / MFD (NMEA 0183)AIS (NMEA 0183 HS)1 Shield GROUND, NMEA 0183 OUT (-) 4800bps RS232 OUT (-) 38.5 kbps2 Orange NMEA 0183 OUT (+) 4800bps3 White RS422 OUT (-) 38.5 kbps4 Green NMEA 0183 IN (-) 4800bps5 Yellow NMEA 0183 IN (+) 4800bps6 Black RS422 OUT (+) 38.5 kbps7 Blue RS232 OUT (+) 38.5 kbps8 Grey RS232 IN Not usedNote:The GPS connector on the radio is provided with a protective cover. If this connector will not be used, please ensure the protective cover is fitted.Simrad - RS35 Installation Instructions12 Simrad - RS35 Installation Instructions 13
4 - Hailer Horn Wire color Function DetailsWhite (+) Connect to hailer speaker +Shield (-) Shield Connect to hailer speaker -Important: Do not short these 2 wires. Install the hailer horn in a forward-facing location on the boat because the hailer horn will transmit the FOG horn sounds and will ‘listen back’ when not transmitting.Note: We recommend you use a hailer horn of 4 Ohms to obtain maximum 30 W audio output power. 5 - External speakerYou can connect 1 x 2 W 8Ω or 1 x 4 W 4Ω speaker to the 3.5 mm speaker connector. A speaker cable with 3.5 mm plug is provided to make the connection to the speaker.Wire color Function DetailsWhite Speaker (+) Connect this wire to the positive terminal of the speaker.Black Speaker (-) Connect this wire to the negative terminal of the speaker.6, 7 - DC Power Wire color Function Details6 - Red (+) 13.6 V DC Connect this wire to the positive battery terminal. Use at least a 10 A fused 13.6 V DC electrical service to the radio.7 - Black (-) Ground Connect this wire to the battery negative terminal.8 - GroundThe vessels battery negative must be common to the boat’s Ground. (Optional) You can connect the base station to the boat’s Ground. Use the Ground screw and Ground plain washer supplied to make this connection.3.2 Wiring diagram - NMEA 2000 connectionsNMEA 2000 NetworkVHF AntennaLink8 VHF120T120T+12 VDCGPS AntennaT-ConnectorsFuse 5ASwitchPower 12 VDC onlyMultifunction DisplayMARKMOBGOTOMENUPAGESSTBYINMOBOUTAUTOSIMRADNSS 7PUSH TO ENTERSimrad - RS35 Installation Instructions14 Simrad - RS35 Installation Instructions 15
VHF AntennaLink8 VHF5External Speaker Hailer SpeakerVHF Antenna3.3 Wiring diagram - External speaker and hailer 3.4 Wiring diagram - NMEA 0183 connectionsRS35 VHFGPS Plotter+12 VDCFuse SwitchPower 12 VDC only1. ShieldNMEA0183 In 4800DSC InformationNMEA0183 OutGPS PositionRS422 38,400AIS Information2. Orange3. White4. Green5.Yellow6.Black7. Blue N/C8.Grey N/C+-+-+-RedBlackWhiteShieldSimrad - RS35 Installation Instructions16 Simrad - RS35 Installation Instructions 17
4 HS35 Handset installation1. Choose a suitable location that ensures sufficient room is allocated to allow the HS35 handset to fit securly in the charging bracket.2. Hold the supplied mounting bracket at the chosen location and use a soft pencil to mark the 3 screw holes and 1 wire hole positions onto the mounting surface.3. Drill the 3 screw holes ( 4.0 mm) and 1 wire hole ( 3.5mm) where marked. Drill completely through the mounting surface.Note: If you are drilling into fiberglass, use a small drill bit to drill pilot holes before drill-ing the screw holes.4. Feed the DC connection wire through the wire hole (lower hole).5. Use the flat screws, spring washers, plain washers, and nuts to attach the mounting bracket to the location site OR, if you cannot reach behind the mounting surface to attach the nuts, use the self-tapping screws instead of the flat screws.6. Connect the DC connection wire to a 12V DC source via a 1A fuse. Red wire to battery (+), Black wire to battery (-).Drill 1 x 3.5mm Wire holeDrill 3 x 4.0mm mounting holesSimrad - RS35 Installation Instructions18 Simrad - RS35 Installation Instructions 19
4 Setup your radio - Your user MMSI CAUTIONYou can’t make any DSC transmissions until you’ve obtained a user MMSI and entered it into your radio.You must enter your User MMSI before the DSC functions of this radio will work.See the Setup section in the RS35 User Guide for full setup details. CAUTIONUnder extreme operating conditions, the temperature of the rear heat-sink on this radio may exceed normal surface temperatures. Caution is advised to prevent possible skin burns.Simrad - RS35 Installation Instructions20 1177*988-10259-001*

Navigation menu