Nec Express5800 120Li Getting Started Guide 856 125212 101 00

: Nec Nec-Express5800-120Li-Getting-Started-Guide-728467 nec-express5800-120li-getting-started-guide-728467 nec pdf

Open the PDF directly: View PDF .
Page Count: 2

Download
Open PDF In Browser	View PDF

Getting Started!
Safety Precautions

1

Follow the instructions for your safety to use the NEC
Express server.
WARNING LABELS

4

5

Installing Hard Disk Drives

Installing the Server

The accessory box contains:

Your server does not contain any hard disk drives. Follow
these steps to install the hard disk drive.
If you have additional adapter boards and devices for your
server, install them before putting the server in the location
you have selected. Follow procedures in the Upgrading Your
Server chapter of your User ’s Guide, plus installation inserts
and vendor documents that come with the option.

Follow the Server Setting Up Information in your User ’s
Guide to install your server.

•
•
•
•
•
•
•
•
•
•

SAFETY NOTES
Read this section carefully to ensure proper and safe use of
the server (Refer to User ’s Guide for detail).

•

Failure to heed this sign could result in personal injury
or damage to properties.
• Keep water or foreign matter away from the server.
• Plug into a proper power source.
• Do not connect the power cord to an outlet that has an
illegal number of connections.
• Insert the power plug into the outlet as far as it goes.
• Use the authorized power cord only.
• Use the attached power cord only for your server.
• Never attempt to lift the server only by yourself.
• Do not install the server in any place other than specified.
• Keep the bottom stabilizers brought out completely
when in use to prevent the server from falling down.
• Do not connect any interface cable when the power
cord of the server is plugged into a power source.
• Do not use any unauthorized interface cable.
• Avoid installation in extreme temperature conditions.
• Make sure of complete board installation.
• Protect the unused connectors with the protective cap.
• Do not touch the fan blades when moving.
• Avoid contact with the server during thunderstorms.
• Keep animals away from the server.
• Do not place any object on top of the server.
• Do not use a cellular phone or pager around the server.

2

5-2006, Rev.00

Checking the Accessory Box

The warning labels are attached to components with possible
d a n g e r o r th e i r v ic i ni t y i n y o u r s er v e r t o i nf o r m t h e u s e r t h a t a
hazardous situation may arise when operating the server. (Do
n o t i n t e n ti o n a l l y r e m o v e o r d a m a g e a n y o f t h e l a b e l s . )
If you find any labels totally/partially removed or illegible due
to damage, contact your sales representative.

Failure to heed this sign could result in serious injury or
death.
• Do not use the server for services where critical high
availability may directly affect human lives.
• Do not use the server if any smoke, odor, or noise is
present.
• Keep needles or metal objects away from the server.
• Do not hold the power plug with a wet hand.
• Do not disassemble, repair, or alter the server.
• Do not look into the CD-ROM drive.
• Do not remove the lithium battery.
• Disconnect the power plug before accessing inside the
server, or connecting the peripherals.

Fol l ow t hese st eps t o become f ami l i ar w i t h your server document at i on and
t o compl et e your i nst al l at i on successf ul l y.

Right 5-inch device rail (2)
Left 5-inch device rail (2)
Right DLT rail (1)
Left DLT rail (1)
Power cord (1)
Keyboard (1)
Mouse (1)
Security key (2)
DianaScope License
NEC EXPRESSBUILDER bootable CD-ROM containing
the setup utility and system documentation
Getting Started! (this guide)

•
•

Save the packing material and carton box in case you ever
need to repack and move the server to another location.

3

Your System Documentation
•

To read and print the User's Guide, insert NEC
EXPRESSBUILDER CD-ROM into the CD-ROM drive
on a system running Microsoft® Windows® (Windows
95 or later, Windows NT 4.0 or later).
Use Adobe ® Acrobat® Reader to read and print the
documents. If you do not have it, install it from NEC
EXPRESSBUILDER CD-ROM.

To order a disk, contact your sales representative or
dealer.
E l e c t r os t a t i c d i s c h a r g e ( E S D ) c a n d a m a g e d i s k
drives, boards, and other parts. This system can
withstand normal levels of environmental ESD while
you are installing hard disk drives. However, we
recommend that you do all procedures in this
instruction only at an ESD workstation or provide
some ESD protection by wearing an antistatic wrist
strap attached to chassis ground – any unpainted
metal surface – on your system when handling
parts.

1.

Unlock the front bezel and
open the bezel.

2.

Locate the hard disk drive bay.

3.

Remove the sponge blocks if
two or more hard disk drives
are to be installed.

C A U T I O N : Kee p the bo tto m s t abiliz ers bro ught o ut co mpletely when in use to prevent the server from falling down.
Do not install the server in the following locations as it may
cause malfunctions of the server.

4.

Open the drive carrier locking
lever.

Click here to view or print User ’s
Guide and other documents.

5.

Align the drive carrier with the
bay guide rails.

6.

Slide the drive carrier into the
bay until it docks with the SCSI
backplane connector.

7.

Click here to install the PDF
viewer (Adobe Acrobat Reader).

Press the carrier lever into its
locked position so that it is
flush with the front of the
carrier.

•

Places with drastic changes in temperature (e.g., near a
heater, air conditioner, or refrigerator)

•

Places with strong vibration

•

Places with corrosive gas in presence, near chemicals,
or with possibilities of chemicals sprayed over

•

On a non-antistatic carpet

•

Places with possibilities of falling objects

•

Places where a power outlet that shares the ground line
with another (especially the one to which a device with
large power consumption is connected) must be used
for the server

•

Do not install the server near equipment that generates
power noise (e.g., contact spark at power-on/power-off
of commercial power supply through a relay). To install
the server near equipment that generates power noise,
ask your sales agent for separating the power wiring or
installing a noise filter.
See the back side to continue the setting up.

Right Wrong

455-01884455-01884-000

6

8

Connecting the Peripherals

Configuring the Server

Connect the peripherals with the server (The following figure shows the redundant
hot-plug power supply model).

Configure the server with the BIOS Setup Utility and SCSI/RAID Configuration
Utilities.
BIOS Setup Utility

10

Installing Application Software
•

Put the NEC EXPRESSBUILDER CD-ROM in the CD-ROM drive on a system running Microsoft Windows(Windows 95 or later, Windows NT 4.0 or
later). The following menu will appear automatically.

The BIOS Setup Utility is used to change system configuration parameters. The
utility is resident in the system FLASH memory and does not require a diskette
or an operating system present to run.
You access the BIOS Setup utility when you turn on or reboot your system. To run
the BIOS Setup Utility, perform the following procedure:
1.
2.

Power-on or reboot the system. “Press  to enter SETUP” displays.
Press F2. The BIOS Setup Utility starts and the Main Menu is displayed.

SCSI Configuration Utility
USB
device

The SCSI configuration utility is used to change default values and check and/or
change SCSI device settings that may conflict with those of other devices in the
server.
To run the SCSI configuration utility, perform the following procedure:
1.
Mouse

Keyboard

Serial
interface
device

2.
Connect the
power plug to
the wall outlet
after
completing all
connections.

Power-on or reboot the system. “Press   for SCSISelect(TM) utility!”
displays.
Press Ctrl-A. The SCSI configuration utility starts and the channel selection
menu is displayed.

Optional RAID Configuration Utility
The RAID configuration utility allows you to configure your disk array. The RAID
controllers support various versions of RAID technology (RAID level). To use any
RAID level, you must configure the RAID controller using the RAID configuration
utility prior to installing your Network Operating System.
For an explanation of these utility, refer to the documentation that was shipped with
these controllers.

LAN device

Running the NEC EXPRESSBUILDER CD-ROM
•

7

•

9

Run the NEC EXPRESSBUILDER CD-ROM to:
•
•
•

USB device

Turning on the Server

Run the maintenance utilities.
Install the Network Operating System (NOS).
Create driver diskettes, BIOS update diskettes and so on.

2

•

Read documentation.
Install the management software.

Refer to Installing and Using Utilities in your User's Guide for detail.

FCC STATEMENT:
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CE STATEMENT:
Warning: This is a Class A product. In domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures (EN55022).
BSMI STATEMENT:

To run the NEC EXPRESSBUILDER CD-ROM, insert the CD-ROM into the
CD-ROM device, reboot the system and follow the screen prompts.

NEC Express5800 Server Solutions Web Site
http://www.necam.com/servers/products/

Press the POWER switch on the front of the server to power-up the server. If your
server does not include Network Operating System (NOS) software, use the DOS
diskettes to boot-up the DOS prompt indicating your system is operational.

1

•
•

The Optional RAID controller include the configuration utility.

Monitor

Serial interface device

Use this menu to:

Trademarks
NEC ESMPRO and NEC EXPRESSBUILDER are trademarks of NEC Corporation. Microsoft and
Windows are registered trademarks of Microsoft Corporation in the United States and other countries.

Locked Unlocked
P os i t i o n Po s i t i o n

Adobe, Adobe logo, and Acrobat are trademarks of Adobe Systems Incorporated.

P OW ER/ S LEEP LED
(
)turned on.

All other product, brand, or company names used in this publication are the trademarks or registered
trademarks of their respective holders.

NOTE: If you plan to run your server on the Microsoft Windows network operating system (NOS), update the graphics accelerator driver upon completion of
installation of NOS. Refer to Chapter 5 in User ’s Guide for details.

To allow for design and specification improvements, the information in this document is subject to
change at any time, without notice. Reproduction of this document or portions thereof without prior
written approval of NEC is prohibited.
Recycled paper is used.

Copyright © 2006 NEC Corporation



File Type                       : AI
File Type Extension             : ai
MIME Type                       : application/vnd.adobe.illustrator
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 5.0.5 for Macintosh
Create Date                     : 2006:04:28 01:33:11Z
Modify Date                     : 2007:02:16 15:29:55-08:00
Metadata Date                   : 2007:02:16 15:29:55-08:00
Creator Tool                    : Illustrator
Thumbnail Format                : JPEG
Thumbnail Width                 : 180
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 23535 bytes, use -b option to extract)
Document ID                     : uuid:36668da3-6b04-48cb-a569-6506baec505e
Instance ID                     : uuid:f2392b3c-2a91-483d-88f9-1e70973dbfe9
Format                          : application/pdf
Page Count                      : 2
Creator                         : Adobe Illustrator(R) 11.0
For                             : NEC SAM, NEC Solutions, America, Inc.
Title                           : 856-125212-101-00.pdf
Bounding Box                    : 12 11 823 1171
Creator Version                 : 11
Container Version               : 9
Image Height                    : 1160
Image Width                     : 811
Image Size                      : 811x1160
Megapixels                      : 0.941