Nec Np400 Users Manual

NP500 to the manual 5d7bc9b5-ca9d-4dd5-8f4c-99014866dcf6

2015-01-24

: Nec Nec-Np400-Users-Manual-331564 nec-np400-users-manual-331564 nec pdf

Open the PDF directly: View PDF .
Page Count: 99

Download
Open PDF In Browser	View PDF

Portable Projector

NP600/NP500/NP400
NP500W
User’s Manual

The projector’s model name indicated on the projector’s label is
NP600, NP500, NP400, NP500W, NP600G, NP500G, NP400G, and
NP500WG respectively.
All the models are referred to as NP600, NP500, NP400, and NP500W
throughout the user’s manual except some of the specification
pages.

1st edition July 2008

• IBM is a trademark or registered trademark of International Business Machines Corporation.
• Macintosh, Mac OS X and PowerBook are trademarks of Apple Inc. registered in the U.S. and other countries.
• Microsoft, Windows, Windows Vista, and PowerPoint are either a registered trademark or trademark of Microsoft
Corporation in the United States and/or other countries.
• VESA is a registered trademark of Video Electronics Standards Association.
• MicroSaver is a registered trademark of Kensington Computer Products Group, a division of ACCO Brands.
• Other product and company names mentioned in this user’s manual may be the trademarks or registered trademarks
of their respective holders.

NOTES
(1) The contents of this user’s manual may not be reprinted in part or whole without permission.
(2) The contents of this user’s manual are subject to change without notice.
(3) Great care has been taken in the preparation of this user’s manual; however, should you notice any questionable
points, errors or omissions, please contact us.
(4) Notwithstanding article (3), NEC will not be responsible for any claims on loss of profit or other matters deemed
to result from using the Projector.

Important Information
Safety Cautions
Precautions
Please read this manual carefully before using your NEC NP600/NP500/NP400/NP500W projector and keep the
manual handy for future reference.
CAUTION
To turn off main power, be sure to remove the plug from power outlet.
The power outlet socket should be installed as near to the equipment as possible, and should be easily
accessible.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABINET.
THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical
shock. Therefore, it is dangerous to make any kind of contact with any part inside of the unit.
This symbol alerts the user that important information concerning the operation and maintenance of this
unit has been provided.
The information should be read carefully to avoid problems.
WARNING: TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
DO NOT USE THIS UNIT’S PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL THE PRONGS
CAN BE FULLY INSERTED.

DOC Compliance Notice (for Canada only)
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Machine Noise Information Regulation - 3. GPSGV,
The highest sound pressure level is less than 70 dB (A) in accordance with EN ISO 7779.
CAUTION
Avoid displaying stationary images for a prolonged period of time.
Doing so can result in these images being temporarily sustained on the surface of the LCD panel.
If this should happen, continue to use your projector. The static background from previous images will
disappear.

Disposing of your used product
EU-wide legislation as implemented in each Member State requires that used electrical and electronic
products carrying the mark (left) must be disposed of separately from normal household waste. This includes projectors and their electrical accessories or lamps. When you dispose of such products, please
follow the guidance of your local authority and/or ask the shop where you purchased the product.
After collecting the used products, they are reused and recycled in a proper way. This effort will help us
reduce the wastes as well as the negative impact such as mercury contained in a lamp to the human
health and the environment at the minimum level.
The mark on the electrical and electronic products only applies to the current European Union Member
States.

Important Information
WARNING TO CALIFORNIA RESIDENTS:
Handling the cables supplied with this product will expose you to lead, a chemical known to the State of California
to cause birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.

RF Interference (for USA only)
WARNING
The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those
specified by NEC Display Solutions of America, Inc. in this manual. Failure to comply with this government regulation could void your right to operate this equipment. This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
For UK only: In UK, a BS approved power cable with moulded plug has a Black (five Amps) fuse installed for use with
this equipment. If a power cable is not supplied with this equipment please contact your supplier.

Important Safeguards
These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them
carefully and heed all warnings.

Installation
• Do not place the projector in the following conditions:
- on an unstable cart, stand, or table.
- near water, baths, or damp rooms.
- in direct sunlight, near heaters, or heat radiating appliances.
- in a dusty, smoky or steamy environment.
- on a sheet of paper or cloth, rugs or carpets.
• If you wish to have the projector installed on the ceiling:
- Do not attempt to install the projector yourself.
- The projector must be installed by qualified technicians in order to ensure proper operation and reduce the risk
of bodily injury.
- In addition, the ceiling must be strong enough to support the projector and the installation must be in accordance
with any local building codes.
- Please consult your dealer for more information.

Important Information
Place the projector in a horizontal position
The tilt angle of the projector should not exceed 10 degrees, nor should the projector be installed in any way other
than the desktop and ceiling mount, otherwise lamp life could decrease dramatically.

10˚

Fire and Shock Precautions
• Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside your
projector. Allow at least 4 inches (10cm) of space between your projector and a wall.
• Do not try to touch the ventilation outlet on the left front (when seen from the front) as it can become heated while
the projector is turned on and immediately after the projector is turned off.
• Prevent foreign objects such as paper clips and bits of paper from falling into your projector. Do not attempt to retrieve
any objects that might fall into your projector. Do not insert any metal objects such as a wire or screwdriver into your
projector. If something should fall into your projector, disconnect it immediately and have the object removed by a
qualified service personnel.
• Do not place any objects on top of the projector.
• Do not touch the power plug during a thunderstorm. Doing so can cause electrical shock or fire.
• The projector is designed to operate on a power supply of 100-240V AC 50/60 Hz (NP600/NP500/NP400/NP500W)
or 200-240V AC 50/60 Hz (NP600G/NP500G/NP400G/NP500WG). Ensure that your power supply fits this requirement before attempting to use your projector.
• Do not look into the lens while the projector is on. Serious damage to your eyes could result.
• Keep any items such as magnifying glass out of the light path of the projector. The light being projected from the
lens is extensive, therefore any kind of abnormal objects that can redirect light coming out of the lens, can cause
unpredictable outcome such as fire or injury to the eyes.
• Do not cover the lens with the black lens cap or equivalent while the projector is on. Doing so can lead to melting
of the cap and possibly burning your hands due to the heat emitted from the light output.
• Do not place any objects, which are easily affected by heat, in front of the projector lens or a projector exhaust
vent.
Doing so could lead to the object melting or getting your hands burned from the heat that is emitted from the light
output and exhaust.
• Handle the power cable carefully. A damaged or frayed power cable can cause electric shock or fire.
- Do not use any power cables than the supplied one.
- Do not bend or tug the power cable excessively.
- Do not place the power cable under the projector, or any heavy object.
- Do not cover the power cable with other soft materials such as rugs.
- Do not heat the power cable.
- Do not handle the power plug with wet hands.
• Turn off the projector, unplug the power cable and have the projector serviced by a qualified service personnel under
the following conditions:
- When the power cable or plug is damaged or frayed.
- If liquid has been spilled into the projector, or if it has been exposed to rain or water.
- If the projector does not operate normally when you follow the instructions described in this user’s manual.
- If the projector has been dropped or the cabinet has been damaged.
- If the projector exhibits a distinct change in performance, indicating a need for service.
• Disconnect the power cable and any other cables before carrying the projector.
• Turn off the projector and unplug the power cable before cleaning the cabinet or replacing the lamp.
• Turn off the projector and unplug the power cable if the projector is not to be used for an extended period of time.
• When using a LAN cable:
For safety, do not connect to the connector for peripheral device wiring that might have excessive voltage.

iii

Important Information
CAUTION
• Do not use the tilt-foot for purposes other than originally intended. Misuses such as gripping the tilt-foot or hanging on the wall can cause damage to the projector.
• Do not send the projector in the soft case by parcel delivery service or cargo shipment. The projector inside the
soft case could be damaged.
• Select [HIGH] in Fan mode if you continue to use the projector for consecutive days. (From the menu, select
[SETUP] - [OPTIONS(1)] → [FAN MODE] → [HIGH].)
• Do not try to touch the ventilation outlet on the left front (when seen from the front) as it can become heated while
the projector is turned on and immediately after the projector is turned off.
• Do not turn off the AC power for 60 seconds after the lamp is turned on and while the POWER indicator is blinking green. Doing so could cause premature lamp failure.

Remote Control Precautions
• Handle the remote control carefully.
• If the remote control gets wet, wipe it dry immediately.
• Avoid excessive heat and humidity.
• Do not heat, take apart, or throw batteries into fire.
• If you will not be using the remote control for a long time, remove the batteries.
• Ensure that you have the batteries’ polarity (+/-) aligned correctly.
• Do not use new and old batteries together, or use different types of batteries together.
• Dispose of used batteries according to your local regulations.

Lamp Replacement
• To replace the lamp, follow all instructions provided on page 72.
• Be sure to replace the lamp when the message [THE LAMP HAS REACHED THE END OF ITS USABLE LIFE.
PLEASE REPLACE THE LAMP.] appears. If you continue to use the lamp after the lamp has reached the end
of its usable life, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case. Do not touch
them as the pieces of glass may cause injury.
If this happens, contact your dealer for lamp replacement.

A Lamp Characteristic
The projector has a high-pressure mercury lamp as a light source.
A lamp has a characteristic that its brightness gradually decreases with age. Also repeatedly turning the lamp on
and off will increase the possibility of its lower brightness.
CAUTION:
When removing the lamp from a ceiling-mounted projector, make sure that no one is under the projector. Glass
fragments could fall if the lamp has been burned out.

Important Information
About High Altitude mode
• Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5500 feet/1600 meters or
higher.
Using the projector at altitudes approximately 5500 feet/1600 meters or higher without setting to [HIGH ALTITUDE]
can cause the projector to overheat and the protector could shut down. If this happens, wait a couple minutes and
turn on the projector.
• Using the projector at altitudes less than approximately 5500 feet/1600 meters and setting to [HIGH ALTITUDE]
can cause the lamp to overcool, causing the image to flicker. Switch [FAN MODE] to [AUTO].
• Using the projector at altitudes approximately 5500 feet/1600 meters or higher can shorten the life of optical components such as the lamp.

About Copyright of original projected pictures:
Please note that using this projector for the purpose of commercial gain or the attraction of public attention in a venue
such as a coffee shop or hotel and employing compression or expansion of the screen image with the following functions may raise concern about the infringement of copyrights which are protected by copyright law.
[ASPECT RATIO], [KEYSTONE], Magnifying feature and other similar features.

Table of Contents
Important Information. ...........................................................................................i
1. Introduction........................................................................................................... 1
1 What’s in the Box?.......................................................................................................... 1
 Introduction to the Projector........................................................................................... 2
Congratulations on Your Purchase of the Projector.................................................. 2
Features you’ll enjoy:................................................................................................ 2
About this user’s manual........................................................................................... 3
 Part Names of the Projector........................................................................................... 4
Front/Top................................................................................................................... 4
Rear.......................................................................................................................... 4
Top Features............................................................................................................. 5
Terminal Panel Features........................................................................................... 6
 Part Names of the Remote Control................................................................................ 7
Battery Installation.................................................................................................... 8
Remote Control Precautions..................................................................................... 8
Operating Range for Wireless Remote Control......................................................... 8

2. Installation and Connections...................................................................... 9
 Setting Up the Screen and the Projector........................................................................ 9
Selecting a Location................................................................................................. 9
Throw Distance and Screen Size............................................................................ 11
 Making Connections..................................................................................................... 13
Enabling the computer’s external display................................................................ 13
Connecting Your PC or Macintosh Computer.......................................................... 13
When Viewing a DVI Digital Signal......................................................................... 15
Using Two Analog COMPUTER Inputs Simultaneously.......................................... 16
Connecting an External Monitor............................................................................. 17
Connecting Your DVD Player with Component Output............................................ 18
Connecting Your VCR............................................................................................. 19
Connecting the Supplied Power Cable................................................................... 21

3. Projecting an Image (Basic Operation)............................................... 22
 Turning on the Projector............................................................................................... 22
Note on Startup screen (Menu Language Select screen)....................................... 23
 Selecting a Source....................................................................................................... 24
Selecting the computer or video source................................................................. 24
 Adjusting the Picture Size and Position........................................................................ 25
Adjust the Tilt Foot.................................................................................................. 26
Zoom....................................................................................................................... 27
Focus...................................................................................................................... 27
 Correcting Keystone Distortion..................................................................................... 28
Correcting Keystone Distortion............................................................................... 28
Adjusting with buttons on the cabinet..................................................................... 28
Adjusting with the Remote Control......................................................................... 29
Adjusting with the Auto Keystone Function............................................................. 30
 Optimizing Computer Signal Automatically.................................................................. 31
Adjusting the Image Using Auto Adjust................................................................... 31
 Turning Up or Down Volume......................................................................................... 31

Table of Contents
7 Turning off the Projector............................................................................................... 32
 After Use...................................................................................................................... 33

4. Convenient Features. .................................................................................... 34
1 Turning off the Image and Sound................................................................................. 34
2 Freezing a Picture........................................................................................................ 34
 Enlarging a Picture....................................................................................................... 34
 Changing Lamp Mode.................................................................................................. 35
 Preventing the Unauthorized Use of the Projector [SECURITY].................................. 36
 Using the Optional Remote Mouse Receiver (NP01MR)............................................. 39
7 Network Setting by Using an HTTP Browser................................................................ 41
8 Using the VGA Signal Cable to Operate the Projector (Virtual Remote)...................... 44

5. Using On-Screen Menu. ............................................................................... 45
 Using the Menus........................................................................................................... 45
2 Menu Elements............................................................................................................. 46
3 List of Menu Items........................................................................................................ 47
4 Menu Descriptions & Functions [SOURCE]................................................................. 49
5 Menu Descriptions & Functions [ADJUST]................................................................... 50
6 Menu Descriptions & Functions [SETUP]..................................................................... 57
7 Menu Descriptions & Functions [INFO.]....................................................................... 67
8 Menu Descriptions & Functions [RESET]..................................................................... 69

6. Maintenance....................................................................................................... 70
 Cleaning or Replacing the Filters................................................................................. 70
2 Cleaning the Cabinet and the Lens.............................................................................. 71
 Replacing the Lamp..................................................................................................... 72

7. Appendix............................................................................................................... 75
 Troubleshooting............................................................................................................ 75
Indicator Messages................................................................................................. 75
 Specifications............................................................................................................... 78
 Cabinet Dimensions..................................................................................................... 80
 Pin Assignments of D-Sub COMPUTER Input Connector........................................... 81
Mini D-Sub 15 Pin Connector................................................................................. 81
 Compatible Input Signal List......................................................................................... 82
 PC Control Codes and Cable Connection.................................................................... 83
PC Control Codes................................................................................................... 83
Cable Connection................................................................................................... 83
PC Control Connector (D-SUB 9P)......................................................................... 83
 Troubleshooting Check List........................................................................................... 84
 TravelCare Guide.......................................................................................................... 86

vii

1. Introduction
1 What’s in the Box?
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
Please save the original box and packing materials if you ever need to ship your projector.

P
M
LA US
AT
ST

CE
UR
SO

J.
AD
TO
AU

Projector

CT
LE
SE

CU
FO

U
EN

ENTER

EXIT

Lens cap
(24F44681)

Soft case
(24BS7582)

O
FF

M
AG
ER

PIC

NIF

-M

E
UP

M
N
W
DO

EN
TE
R

LCLI
CK
IT

S-V
ID
EO

VO
LU
M

E
AS
PE

PIC

CK
LI
R-C
J.
AD
TO
E
E
US R AU
O
OD
M
TE
M
P
PU
M
M
LA
CO 1

VID
LP

TU
FR
EE
ZE

Power cable
(US: 7N080229)
(EU: 7N080015)

VGA signal cable
(7N520052)

Remote control
(7N900731)

Batteries (AAA2)

For North America only
Registration card
Limited warranty

Quick Setup Guide
(7N8P8811)
Important Information
(7N8P8821)

CD-ROM
User’s manual
(7N951211)

DVI to VGA adapter (7N960233)

For Europe only
Guarantee policy

1. Introduction

 Introduction to the Projector
This section introduces you to your new projector and describes the features and controls.

Congratulations on Your Purchase of the Projector
This projector is one of the very best projectors available today. The projector enables you to project precise images
up to 300 inches across (measured diagonally) from your PC or Macintosh computer (desktop or notebook), VCR,
DVD player, or document camera.
You can use the projector on a tabletop or cart, you can use the projector to project images from behind the screen,
and the projector can be permanently mounted on a ceiling*1. The remote control can be used wirelessly.
*1 Do not attempt to mount the projector on a ceiling yourself.
The projector must be installed by qualified technicians in order to ensure proper operation and reduce the risk
of bodily injury.
In addition, the ceiling must be strong enough to support the projector and the installation must be in accordance
with any local building codes. Please consult your dealer for more information.

Features you’ll enjoy:
• Quick start & Direct Power Off

Eight seconds after turning on the power, the projector is ready to display PC or video images.

The projector has a feature called “Direct Power Off”. This feature allows the projector to be turned off (even when
projecting an image) using a power strip equipped with a switch and a breaker.

• AUTO POWER ON and AUTO POWER OFF features

The AUTO POWER ON(AC), AUTO POWER ON(COMP1), AUTO POWER OFF, and OFF TIMER features eliminate
the need to always use the POWER button on the remote control or projector cabinet.

• Virtual Remote function

The Virtual Remote function allows power On/Off and source selection of the projector from your PC by using the
supplied VGA signal cable. The utility software “Virtual Remote Tool” exclusively for the projector is required to be
downloaded from our website.

• The optional remote control (NP02RC) allows you to assign a CONTROL ID to the projector

Multiple projectors can be operated separately and independently with the same single remote control by assigning
an ID number to each projector.

• A variety of input ports and a comprehensive array of system control interfaces

This projector supports input signals on the following ports: DVI-I connector (DVI-I 29 Pin) with HDCP compatible,
15pin D-Sub, composite and S-video.

• Integrated RJ-45 connector for wired networking capability

An RJ-45 connector is equipped as standard feature.

• 7W built-in speaker for an integrated audio solution

Powerful 7 watt speaker provides volume need for large rooms.

• Auto vertical keystone correction

Auto Keystone feature allows the projector to detect its tilt and correct vertical distortion automatically.

• LCD projector with high resolution and high brightness

High resolution display - up to UXGA compatible, XGA (NP600/NP500/NP400)/WXGA (NP500W) native resolution.

• Six picture preset modes for user adjustable picture and color settings

Each picture preset mode can be customized and memorized according to your preference.

1. Introduction
• Preventing unauthorized use of the projector

Enhanced smart security settings for keyword protection, cabinet control panel lock, security slot, and security
chain opening to help prevent unauthorized access, adjustments and theft deterrence.

• PC Control Port

You can control the projector with a PC or control system using the PC Control port.

• 3W in standby condition with energy saving technology

Selecting [POWER-SAVING] for [STANDBY MODE] from the menu can put the projector in power-saving mode
that consume less power than the normal standby condition.

• Optional remote mouse receiver

You can use the supplied wireless remote control and the optional remote mouse receiver to operate your PC
mouse from across the room. The optional remote mouse receiver (NP01MR) supports almost any PC using a
USB connection.

About this user’s manual
The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to
review the user’s manual. This may save you time later on. At the beginning of each section of the manual you’ll find
an overview. If the section doesn’t apply, you can skip it.

1. Introduction

 Part Names of the Projector
Front/Top
Controls
(→ page 5)

P
M S
LA TU
TA
S

U
A

J.
D
A

Zoom Lever (→ page 27)

O
S

E
C
R
U

Focus Ring
(→ page 27)

T
C
LE
E
S
N
E
M

ENTER

EXIT

C
FO

Remote sensor
(→ page 8)

Security chain opening
Attach an anti-theft device.
The security chain opening accepts security wires or chains up to 0.18 inch/
4.6 mm in diameter.

Built-in Security Slot (

Lens

Ventilation (inlet) / Filter Cover
(→ page 70)

Lens Cap

Adjustable Tilt Foot Lever (→ page 26)
Adjustable Tilt Foot (→ page 26)

* This security slot supports the MicroSaver ® Security System.

Rear
Lamp Cover (→ page 72)
F
O
C
S
U

ENTER

SE
LE
CT

EXIT

SO
UR
CE
AU
TO

LA
MP
ST
AT
US

Monaural Speaker (7W)
Ventilation (inlet) / Filter Cover
(→ page 70)

Ventilation (outlet)
Heated air is exhausted from here.

Terminal Panel (→ page 6)

Spacer (black rubber)
To fine-adjust the height of the rear foot,
remove the spacer and rotate the rear
foot to the desired height.
Rear Foot (→ page 26)
AC Input
Connect the supplied power cable’s two-pin plug here, and
plug the other end into an active wall outlet. (→ page 21)
Main Power Switch
When you plug the supplied power cable into an active wall outlet
and turn on the Main Power, the POWER indicator turns orange
and the projector is in standby mode.
(→ page 22,32)

1. Introduction
Top Features

7
8

SELECT

EX
IT

LAMP
STATUS

12
1.

SOURCE

AUTO ADJ.

(POWER) Button (→page 22, 32)

2. POWER Indicator (→page 22, 32, 75)
3. STATUS Indicator (→page 75)
4. LAMP Indicator (→page 72, 75)
5. SOURCE Button (→page 24)
6. AUTO ADJ. Button (→page 31)
7. MENU Button (→page 45)
8. SELECT  / Volume Buttons  / Keystone
Buttons  (→page 28, 31)
9. ENTER Button
10. EXIT Button

4
3

1. Introduction
Terminal Panel Features

1. COMPUTER 1 IN/ Component Input Connector
(Mini D-Sub 15 Pin) (→page 13,16,18)
2. COMPUTER 2 (DVI-I) IN Connector (29 Pin) (HDCP
compatible) (→page 15,16)
3. AUDIO IN Mini Jack (Stereo Mini)
(→page 13,15,18)
4. AUDIO OUT Mini Jack (Stereo Mini) (→page 17)
5. MONITOR OUT (COMP 1) Connector (Mini D-Sub
15 Pin) (→page 17)
6. S-VIDEO IN Connector (Mini DIN 4 Pin)
(→page 19)
7. VIDEO IN Connector (RCA) (→page 19)
8. AUDIO Input Jacks L/R (RCA) (→page 19)
9. PC CONTROL [PC CONTROL] Port (D-Sub 9 Pin)
(→page 83)
Use this port to connect a PC or control system.
This enables you to control the projector using serial
communication protocol. If you are writing your own
program, typical PC control codes are on page 83.
10. LAN Port (RJ-45) (→page 20)

1. Introduction

 Part Names of the Remote Control
1
OFF

POWER
MAGNIFY PIC-MUTE

PAGE
UP

6
DOWN

ENTER

11
13
14
19
17

5
8

EXIT

L-CLICK

R-CLICK
MOUSE

VIDEO

COMPUTER
COMPUTER AUTO ADJ.

1
S-VIDEO

LAMP MODE

2
VOLUME

ASPECT

HELP

PICTURE

FREEZE

10
12
16
15
18
21
22
20
12. MOUSE R-CLICK Button*
(→ page 39,40)

1. Infrared Transmitter
(→ page 8)

13. VIDEO Button
(→ page 24)

2. POWER ON Button
(→ page 22)

14. S-VIDEO Button
(→ page 24)

3. POWER OFF Button
(→ page 32)

15. COMPUTER 1/2 Button
(→ page 24)

4. MAGNIFY (+)(–) Button
(→ page 34)

16. AUTO ADJ. Button
(→ page 31)

5. PIC-MUTE Button
(→ page 34)

17. VOLUME (+)(–) Button
(→ page 31)

6. PAGE UP/DOWN Button*
(→ page 39,40)

18. LAMP MODE Button (→ page 35)
19. ASPECT Button
(→ page 54)

7. MENU Button
(→ page 45)

20. PICTURE Button
(→ page 50,51)

8. SELECT  Button (→ page 45)
9. ENTER Button (→ page 45)
10. EXIT Button (→ page 45)

21. HELP Button
(→ page 67)

11. MOUSE L-CLICK Button*
(→ page 39,40)

22. FREEZE Button
(→ page 34)

* The PAGE UP/DOWN, MOUSE L-CLICK and MOUSE R-CLICK buttons work only when the optional remote mouse
receiver is connected with your computer.

1. Introduction
Battery Installation

1 Press firmly and slide the
battery cover off.

2 Install new batteries (AAA). En-

3 Slip the cover back over the bat-

sure that you have the batteries’
polarity (+/–) aligned correctly.

teries until it snaps into place. Do
not mix different types of batteries
or new and old batteries.

Remote Control Precautions
•
•
•
•
•
•
•
•

Handle the remote control carefully.
If the remote control gets wet, wipe it dry immediately.
Avoid excessive heat and humidity.
Do not heat, take apart, or throw batteries into fire.
If you will not be using the remote control for a long time, remove the batteries.
Ensure that you have the batteries’ polarity (+/-) aligned correctly.
Do not use new and old batteries together, or use different types of batteries together.
Dispose of used batteries according to your local regulations.

Operating Range for Wireless Remote Control

Remote control

7m/22feet

LAMP

SELECT

FOCUS

EX
IT

SOURCE AUTO ADJ.

30°

STATUS

30°

Remote sensor on projector cabinet

Remote control

30°
30°

7m/22feet

• The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree angle of
the remote sensor on the projector cabinet.
• The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls
on the sensor. Weak batteries will also prevent the remote control from properly operating the projector.

2. Installation and Connections
This section describes how to set up your projector and how to connect video and audio sources.
Your projector is simple to set up and use. But before you get started, you must first:
z Set up a screen and the projector.
x Connect your computer or video equipment to the projector.

(→ page 13,15,16,17,18,19,20)
US

FOC

c Connect the supplied power cable.
(→ page 21)

SELE

ENTER

EXIT

SOUR

STATU

LAMP

ADJ.

AUTO

NOTE: Ensure that the power cable and any other
cables are disconnected before moving the projector. When moving the projector or when it is not
in use, cover the lens with the lens cap.

To the wall outlet.

 Setting Up the Screen and the Projector
Selecting a Location
[NP600/NP500/NP400]
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is
approximately 21" (0.53 m) measured diagonally when the projector is roughly 30 inches (0.8 m) from the wall or
screen. The largest the image can be is 300" (7.6 m) when the projector is about 407 inches (10.3 m) from the wall
or screen.
Screen Size (Unit: cm/inch)
609.6(W)�457.2(H) / 240(W)�180(H)

487.7(W)�365.8(H) / 192(W)�144(H)
406.4(W)�304.8(H) / 160(W)�120(H)
365.8(W)�274.3(H) / 144(W)�108(H)

203.2(W)�152.4(H) / 80(W)�60(H)

1/
20

is
ta
n

4.
1/
16

7
3. "
4/
13
5"

10
7/

LAMP
STATUS

2.
0/
81

AUTOADJ.

ENTER

EXIT

SOURCE

0
30 .8/
1. "
4 0/
1. 0"
3/
53
"

MENU
SELECT

3"
6.
2/
24
4"
6.
ce
9/
27
(U
1"
ni
8.
t:
3/
m
32
/in
5"
ch 10.3
/4
)
07
"

FOCUS

Lens center

60
30
21" "

42.7(W)�32(H) / 17(W)�13(H)

121.9(W)�91.4(H) / 48(W)�36(H)

61.0(W)�45.7(H) / 24(W)�18(H)

12
10

162.6(W)�121.9(H) / 64(W)�48(H)

81.3(W)�61.0(H) / 32(W)�24(H)

243.8(W)�182.9(H) / 96(W)�72(H)

304.8(W)�228.6(H) / 120(W)�90(H)

Screen Size

2. Installation and Connections
[NP500W]
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is
approximately 21" (0.53 m) measured diagonally when the projector is roughly 28 inches (0.7 m) from the wall or
screen. The largest the image can be is 300" (7.6 m) when the projector is about 384 inches (9.7 m) from the wall or
screen.
Screen Size (Unit: cm/inch)
646.2(W)�403.9(H) / 254(W)�159(H)

516.9(W)�323.1(H) / 204(W)�127(H)
430.8(W)�269.2(H) / 170(W)�106(H)
387.7(W)�242.3(H) / 153(W)�95(H)

215.4(W)�134.6(H) / 85(W)�53(H)
172.3(W)�107.7(H) / 68(W)�42(H)

7
9. "
7/
38
4"

8/
7.

5/
6.

9/
4.

15
9/

D
is

ta
nc

/in

ch
)

2
3. "
2/
12
7"

9/
1.

LAMP
STATUS

ENTER

EXIT

AUTOADJ.

0
2 .7/
0. 8"
94
3 /
1. 8"
3/
50
"

FOCUS

MENU
SELECT

SOURCE

"
1"

Lens center

30
21" "

45.2(W)�28.3(H) / 18(W)�11(H)

80
60

64.6(W)�40.4(H) / 25(W)�16(H)

12
10

129.2(W)�80.8(H) / 51(W)�32(H)
86.2(W)�53.8(H) / 34(W)�21(H)

258.5(W)�161.5(H) / 102(W)�64(H)

323.1(W)�201.9(H) / 127(W)�79(H)

Screen Size

TIP:
• The distances are indicated by intermediate values between tele and wide. Use as a rule of thumb.
• The Zoom lever adjusts the image size +/-10%
• For more details on throw distance, see page 11.

2. Installation and Connections
Throw Distance and Screen Size
The following shows the proper relative positions of the projector and screen. Refer to the table to determine the
position of installation.

Distance Chart
C

Screen center

Lens center

D
Screen bottom

Projector bottom

B = Vertical distance between lens center and
screen center
C = Throw distance
D = Vertical distance between lens center and
screen bottom (top of screen for ceiling application)
α = Throw angle
NOTE: The values in the tables are design values and
may vary.

[NP600/NP500/NP400]
Diagonal
inch
mm
21
533
25
635
30
762
40
1016
60
1524
72
1829
80
2032
84
2134
90
2286
100
2540
120
3048
150
3810
180
4572
200
5080
210
5334
240
6096
270
6858
300
7620

Screen Size
Width
mm
427
508
610
813
1219
1463
1626
1707
1829
2032
2438
3048
3658
4064
4267
4877
5486
6096

inch
17
20
24
32
48
58
64
67
72
80
96
120
144
160
168
192
216
240

Height
inch
mm
13
320
15
381
18
457
24
610
36
914
43
1097
48
1219
50
1280
54
1372
60
1524
72
1829
90
2286
108
2743
120
3048
126
3200
144
3658
162
4115
180
4572

B
inch
4
5
6
8
12
15
17
17
19
21
25
31
37
41
43
50
56
62

wide
mm
110
131
157
210
314
377
419
440
471
524
629
786
943
1048
1100
1257
1414
1572

inch
29
36
48
73
87
97
102
110
122
147
184
221
246
258
295
332
369

inch
30
36
43
58
88
105
117
123
132
147
177
221
266
295
310
355
399
444

mm
753
903
1092
1469
2223
2675
2977
3128
3354
3731
4485
5616
6747
7501
7878
9009
10140
11271

tele
mm
746
903
1217
1845
2221
2473
2598
2787
3101
3729
4671
5613
6241
6555
7497
8439
9381

inch
-2
-2
-3
-4
-6
-7
-8
-8
-8
-9
-11
-14
-17
-19
-20
-23
-25
-28

mm
-50
-60
-71
-95
-143
-171
-191
-200
-214
-238
-286
-357
-429
-476
-500
-572
-643
-714

wide
degree
10.0
9.9
9.8
9.7
9.6
9.6
9.6
9.6
9.6
9.6
9.5
9.5
9.5
9.5
9.5
9.5
9.5

mm
-42
-50
-61
-81
-121
-145
-162
-170
-182
-202
-242
-303
-363
-404
-424
-485
-545
-606

wide
degree
9.5
9.4
9.3
9.2
9.2
9.2
9.2
9.2
9.2
9.2
9.1
9.1
9.1
9.1
9.1
9.1
9.1

tele
degree
8.3
8.3
8.2
8.1
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
7.9
7.9
7.9
7.9

[NP500W]
Diagonal
inch
mm
21
533
25
635
30
762
40
1016
60
1524
72
1829
80
2032
84
2134
90
2286
100
2540
120
3048
150
3810
180
4572
200
5080
210
5334
240
6096
270
6858
300
7620

Screen Size
Width
inch
mm
18
452
21
538
25
646
34
862
51
1292
61
1551
68
1723
71
1809
76
1939
85
2154
102
2585
127
3231
153
3877
170
4308
178
4523
204
5169
229
5816
254
6462

inch
11
13
16
21
32
38
42
45
48
53
64
79
95
106
111
127
143
159

mm
283
337
404
538
808
969
1077
1131
1212
1346
1615
2019
2423
2692
2827
3231
3635
4039

Height
inch
4
5
6
7
11
13
15
16
17
19
22
28
33
37
39
45
50
56

wide
mm
99
118
141
188
283
339
377
396
424
471
565
707
848
942
989
1131
1272
1414

inch
28
34
45
68
82
92
96
103
115
138
173
208
231
243
278
313
348

mm
703
851
1146
1737
2092
2328
2446
2624
2919
3510
4396
5283
5874
6169
7056
7942
8829

inch
28
34
41
55
83
100
111
116
125
139
167
209
251
279
293
335
377
419

mm
712
854
1032
1389
2101
2528
2813
2955
3169
3525
4237
5305
6374
7086
7442
8510
9578
10646

tele
inch
-2
-2
-2
-3
-5
-6
-6
-7
-7
-8
-10
-12
-14
-16
-17
-19
-21
-24

tele
degree
7.9
7.9
7.8
7.7
7.7
7.6
7.6
7.6
7.6
7.6
7.6
7.6
7.6
7.6
7.6
7.6
7.6
7.6

2. Installation and Connections
WARNING

Reflecting the Image

* Installing your projector on the ceiling must be done
by a qualified technician. Contact your NEC dealer for
more information.
* Do not attempt to install the projector yourself.
• Only use your projector on a solid, level surface. If the
projector falls to the ground, you can be injured and
the projector severely damaged.
• Do not use the projector where temperatures vary
greatly. The projector must be used at temperatures
between 41˚F (5˚C) and 104˚F (40˚C) (Eco mode selected automatically at 95˚F to 104˚F/35˚C to 40˚C).
• Do not expose the projector to moisture, dust, or
smoke. This will harm the screen image.
• Ensure that you have adequate ventilation around your
projector so heat can dissipate. Do not cover the vents
on the side or the front of the projector.

Using a mirror to reflect your projector’s image enables
you to enjoy a much larger image when a smaller space
is required. Contact your NEC dealer if you need a mirror
system. If you’re using a mirror system and your image
is inverted, use the MENU and SELECT buttons on your
projector cabinet or your remote control to correct the
orientation. (→ page 60)

2. Installation and Connections

 Making Connections
NOTE: When using with a notebook PC, be sure to connect the projector and notebook PC while the projector is in standby mode
and before turning on the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered up.
* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver or power management software.

Enabling the computer’s external display
Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector.
When using a PC compatible laptop, a combination of function keys will enable/disable the external display.
Usually, the combination of the ‘Fn” key along with one of the 12 function keys gets the external display to come on
or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through
external display selections.

Connecting Your PC or Macintosh Computer
NOTE: Signals supported by Plug & Play (DDC2)
INPUT
Model
NP600/NP500/NP400
NP500W

COMPUTER 1 IN
analog
Yes
Yes

COMPUTER 2 IN
analog
No
Yes

digital
Yes
Yes

AUDIO IN

COMPUTER 1 IN

VGA signal cable (supplied)

Audio cable
(not supplied)

To mini D-Sub 15-pin connector on the projector. It is
recommended that you use a commercially available distribution amplifier if connecting a signal cable longer than
the cable supplied.

PHONE

IBM VGA or Compatibles (Notebook
type) or Macintosh (Notebook type)

NOTE: For older Macintosh, use a commercially available
pin adapter (not supplied) to connect to your Mac’s video
port.

2. Installation and Connections
• Select the source name for its appropriate input connector after turning on the projector.
Input connector

SOURCE button on the projector
cabinet

COMPUTER 1 IN

COMPUTER1

COMPUTER 2(DVI-I)IN

COMPUTER 2(DIGITAL)
or
COMPUTER 2(ANALOG)

Button on the remote control
(COMPUTER 1)

(COMPUTER 2)
↓ (Toggle)
(COMPUTER 2)

NOTE: The projector is not compatible with video decoded outputs of the NEC ISS-6020 switcher.
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back via a commercially available scan
converter.
This is because the projector will process a video signal as a computer signal at the default setting. In that case, do the following.
* When an image is displayed with the lower and upper black portion of the screen or a dark image is not displayed correctly:
Project an image to fill the screen and then press the AUTO ADJ. button on the remote control or the projector cabinet.

2. Installation and Connections
When Viewing a DVI Digital Signal
To project a DVI digital signal, be sure to connect the PC and the projector using a DVI cable (not supplied) before
turning on your PC or projector. Turn on the projector first and select Computer 2 (Digital) from the source menu before
turning on your PC.
Failure to do so may not activate the digital output of the graphics card resulting in no picture being displayed. Should
this happen, restart your PC.
Do not disconnect the DVI cable while the projector is running. If the signal cable has been disconnected and then
re-connected, an image may not be correctly displayed. Should this happen, restart your PC.
NOTE:
• Use a DVI cable or the one compliant with the DDWG (Digital Display Working Group) DVI (Digital Visual Interface) revision 1.0
standard. The DVI cable should be within 5 m (196") long. Both single and dual types of DVI cable can be used.
• The DVI (DIGITAL) connector accepts VGA (640x480), SVGA (800x600), 1152x864, XGA (1024x768), WXGA (1280x800 @ up
to 60Hz), and SXGA (1280x1024 @ up to 60Hz).

IBM PC or Compatibles (Desktop type)
or Macintosh (Desktop type)

PHONE

Audio cable (not supplied)

AUDIO IN

DVI cable (not supplied)

COMPUTER 2 (DVI-I) IN

2. Installation and Connections
Using Two Analog COMPUTER Inputs Simultaneously
If you need to use two analog COMPUTER inputs simultaneously, connect a VGA signal cable as shown below.
COMPUTER 2 (DVI-I) IN

COMPUTER 1 IN

IBM PC or Compatibles (Desktop
type) or Macintosh (Desktop type)
DVI to VGA adapter
(supplied)

VGA signal cable
(supplied)

VGA signal cable (not
supplied)

IBM PC or Compatibles (Notebook type)
or Macintosh (Notebook type)

NOTE: When the DVI to VGA adapter is not to be used for an extended period of time, remove it from the projector. Failure to do so
may cause damage to the connector of the projector.

2. Installation and Connections
Connecting an External Monitor

AUDIO OUT
MONITOR OUT (COMP 1)

VGA signal cable (not supplied)

VGA signal
cable (supplied)

AUDIO
IN

PHONE

You can connect a separate, external monitor to your projector to simultaneously view on a monitor the computer
analog image you’re projecting.
NOTE:
• Daisy chain connection is not possible.
• When audio equipment is connected, the projector speaker is disabled.

2. Installation and Connections
Connecting Your DVD Player with Component Output

COMPUTER 1 IN

AUDIO IN

15-pin - to - RCA (female) 3 cable adapter
(ADP-CV1E)

Audio Equipment

Component video RCA3
cable (not supplied)

AUDIO IN
L

DVD player
L

Audio cable (not supplied)
AUDIO OUT

Component

A component signal will be automatically displayed. If not, from the menu, select [SETUP] → [OPTIONS(1)] →
[SIGNAL SELECT] → [COMPUTER1], and then place a check mark in the Component radio button.
• Select the source name for its appropriate input connector after turning on the projector.
Input connector
COMPUTER 1 IN

SOURCE button on the projector
cabinet
COMPUTER1

Button on the remote control
(COMPUTER 1)

NOTE: Refer to your DVD player’s owner’s manual for more information about your DVD player’s video output requirements.

2. Installation and Connections
Connecting Your VCR
S-VIDEO IN
AUDIO IN
VIDEO IN

S-Video cable (not supplied)

Audio cable (not supplied)

Video cable (not supplied)

Audio equipment
VCR

AUDIO OUT

VIDEO S-VIDEO

AUDIO IN

VIDEO OUT

Audio cable (not supplied)

• Select the source name for its appropriate input connector after turning on the projector.
Input connector

SOURCE button on the projector
cabinet

Button on the remote control

VIDEO IN

VIDEO

(VIDEO)

S-VIDEO IN

S-VIDEO

(S-VIDEO)

NOTE: The AUDIO IN L and R jacks (RCA) are shared between the Video and S-Video inputs.
NOTE: Refer to your VCR owner’s manual for more information about your equipment’s video output requirements.
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back in fast-forward or fast-rewind via
a scan converter.

2. Installation and Connections
Connecting to a Network
The projector comes standard with a LAN port (RJ-45) which provides a LAN connection using a LAN cable.
Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings for the projector over a LAN.
To use a LAN connection, you are required to assign an IP address to the projector on the [PROJECTOR NETWORK
SETTINGS] screen of the web browser on your computer. For setting, see page 41,42,43.

Example of LAN connection
Example of wired LAN connection
Server

Hub

NOTE: Use a Category 5 or higher LAN cable.

LAN cable (not supplied)

LAN

2. Installation and Connections
Connecting the Supplied Power Cable
Connect the supplied power cable to the projector.
First connect the supplied power cable’s two-pin plug to the AC IN of the projector, and then connect the other plug
of the supplied power cable in the wall outlet.

F
O
U
C
S

ENTER

LE
CT

LAMP
EXIT

SO
UR
CE

AU
TO
AD

STATUS
SOURCE

AUTO ADJ.

LA
STA MP
TU
S

To wall outlet ←

Make sure that the prongs are fully inserted into both
the AC IN and the wall outlet.

CAUTION:
Do not try to touch the ventilation outlet on the left front (when seen from the front) as it can become heated while
the projector is turned on and immediately after the projector is turned off.

3. Projecting an Image (Basic Operation)
This section describes how to turn on the projector and to project a picture onto the screen.

 Turning on the Projector
NOTE:
• The projector has two power switches: a main power switch and a
(POWER) button (POWER ON and OFF on the remote
control).
• When plugging in or unplugging the supplied power cable, make sure that the main power switch is pushed to the off () position. Failure to do so may cause damage to the projector.

C
FO

1. To turn on the main power to the projector, press the
Main Power switch to the on position ( I ).

S
U

The POWER indicator will light orange.
See the Power Indicator section.(→ page 75)

ME
NU

ENTER

LEC
T

LAMP

EXIT

STATUS

CE
AU

TO
AD

LA
MP
STA
TU
S

SOURCE

AUTO ADJ.

2. Remove the lens cap
• Do not remove the lens cap by pulling on the string.
Doing so can cause mechanical damage to the part
around the lens.
(POWER) button on the projector cabinet
3. Press the
or the POWER ON button on the remote control for 1
second.

LAMP
STATUS
SOURCE

The POWER indicator will turn to green and the projector
will become ready to use.
TIP: When the message “CONTROL PANEL LOCK IS TURNED
ON” is displayed, it means that the [CONTROL PANEL LOCK] is
turned on. (→ page 61)
After you turn on your projector, ensure that the computer
or video source is turned on and that your lens cap is
removed.

NOTE: When no signal is available, the NEC logo, blue (default), or
black screen will be displayed. When the projector displays the NEC
logo, a blue or black screen, the projector will automatically switch
to the ECO mode.
The projector will return to the NORMAL mode once a signal is
connected.

OFF

AUTO ADJ.

ON
POWER

MAGNIFY PIC-MUTE

PAGE
UP

SOURCE

PIC-MUTE

ASPECT

POWER

DOWN

Standby

Blinking

Power On

Blinking green
light

Steady green
light

LAMP
STATUS
SOURCE

AUTO ADJ.

Steady orange light

(→ page 75)

3. Projecting an Image (Basic Operation)
Note on Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one
of the 21 menu languages.
To select a menu language, follow these steps:
1. Use the SELECT , H, F or E button to select one of
the 21 languages from the menu.

OFF

ON
POWER

MAGNIFY PIC-MUTE

PAGE
UP

DOWN

SELECT
MENU

EX
I

R
TE
EN

ENTER

EXIT

OFF

ON
POWER

2. Press the ENTER button to execute the selection.

MAGNIFY PIC-MUTE

PAGE
UP

SELECT

EX
I

R
TE
EN

After this has been done, you can proceed to the menu
operation.
If you want, you can select the menu language later.
(→ [LANGUAGE] on page 47 and 59)

DOWN

ENTER

EXIT

NOTE: Immediately after turning on the projector, screen flicker may occur. This is normal. Wait 3 to 5 minutes until the lamp lighting is stabilized.
NOTE: If you turn on the projector immediately after the lamp is turned off or when the temperature is high, the fans run without
displaying an image for some time and then the projector will display the image.
CAUTION:
The projector cannot be turned off for 60 seconds after the lamp is turned on and while the POWER indicator is blinking
green. Doing so could cause premature lamp failure.
When the [LAMP MODE] is set to [ECO], the LAMP indicator will light green.
If one of the following things happens, the projector will not turn on.
• If the internal temperature of the projector is too high, the projector detects abnormal high temperature. In this
condition the projector will not turn on to protect the internal system. If this happens, wait for the projector’s internal
components to cool down.
• When the lamp reaches its end of usable life, the projector will not turn on. If this happens, replace the lamp.
• If the lamp fails to light, and if the STATUS indicator flashes on and off in a cycle of six times, wait a full minute and
then turn on the power.
NOTE: Turning the Main Power Switch Off then Back On
Allow a minimum of 1 second between turning off the main power switch and turning it back on again.
The same will be applied when a power strip equipped with a switch and a breaker is used.
Failing to do so could result in no power to the projector. (There will be no stand-by LED)
Should this happen, unplug the power cable and plug it in again. Turn on the main power switch.

3. Projecting an Image (Basic Operation)

 Selecting a Source
Selecting the computer or video source
NOTE: Turn on the computer or video source equipment connected to the projector.

Selecting from Source List

SELECT

TE
EN

Press and quickly release the SOURCE button on the projector cabinet to
display the Source list. Each time the SOURCE button is pressed, the input
source will change as follows: “COMPUTER1”, “COMPUTER2(DIGITAL/
ANALOG)”, ”VIDEO”, “S-VIDEO”, To display the selected source, allow
1 second to elapse.

LAMP
STATUS
SOURCE

AUTO ADJ.

Detecting the Signal Automatically
Press and hold the SOURCE button for a minimum of 2 seconds, the
projector will search for the next available input source. Each time you
press and hold the SOURCE button for a minimum of 2 seconds, the
input source will change as follows:
COMPUTER1 → COMPUTER2(DIGITAL) → COMPUTER2(ANALOG)
→ VIDEO → S-VIDEO → COMPUTER1 → ...
TIP: If no input signal is present, the input will be skipped.

Using the Remote Control

L-CLICK

R-CLICK

VIDEO

COMPUTER AUTO ADJ.

MOUSE

Press any one of the COMPUTER 1/2, VIDEO, and S-VIDEO buttons.

1
S-VIDEO

LAMP MODE

TIP: The COMPUTER 2 button on the remote control toggles the Computer 2 source
between [COMPUTER2(DIGITAL)] and [COMPUTER2(ANALOG)].

Selecting Default Source
You can set a source as the default source so that it will be displayed
each time the projector is turned on.
1. Press the MENU button.
The menu will be displayed.
2. Press the SELECT  button twice to select [SETUP] and press the
SELECT H button or the ENTER button to select [GENERAL].
3. Press the SELECT  button three times to select [OPTIONS(2)].
4. Press the SELECT H button six times to select [DEFAULT SOURCE
SELECT] and press the ENTER button.
The [DEFAULT SOURCE SELECT] screen will be displayed.
(→ page 66)
5. Select a source as the default source, and press the ENTER button.
6. Press the EXIT button a few times to close the menu.
7. Restart the projector.
The source you selected in step 5 will be projected.
TIP: When the projector is in Standby mode, applying a computer signal from a
computer connected to the COMPUTER 1 IN input will power on the projector
and simultaneously project the computer’s image.
([AUTO POWER ON(COMP1)] → page 66)

VOLUME

ASPECT

HELP

PICTURE

FREEZE

3. Projecting an Image (Basic Operation)

 Adjusting the Picture Size and Position
Use the adjustable tilt foot, the zoom lever or the focus ring to adjust the picture size and position.
In this chapter drawings and cables are omitted for clarity.
Adjusting the throw angle (the height of an image)
[Tilt foot] (→ page 26)

Adjusting the left and right tilt of an image
[Rear foot] (→ page 26)

FOC
US

FOC
US
MENU
SELECT

ENTER

SELECT
EXIT

SOURC

EXIT

E
AUTOA

SOURC

DJ.
E
AUTOA
DJ.

LAMP
STATUS

Finely adjusting the size of an image
[Zoom lever] (→ page 27)

Adjusting the focus
[Focus ring] (→ page 27)

FOC
FOC

MENU
MENU
SELECT

ENTER

SELECT

EXIT
EXIT

SOURC
E

SOURC
AUTOA
DJ.

LAMP
STATUS

AUTOA
DJ.

Adjusting the keystone correction [KEYSTONE]* (→ page 28)

FOC

MENU
SELECT

ENTER

SELECT

EXIT

SOURC

SOURC
E

E
AUTOA
DJ.

AUTOA

LAMP
STATUS

DJ.

LAMP
STATUS

* Keystone correction can be also performed automatically. (→ page 30)

LAMP
STATUS

3. Projecting an Image (Basic Operation)
Adjust the Tilt Foot
1. Lift the front edge of the projector.
CAUTION:
Do not try to touch the ventilation outlet during Tilt Foot adjustment as
it can become heated while the projector is turned on and during its
cool down period after it is turned off.

P
M

J.
AD
TO

AT
ST

S
CU

U
EN

ENTER

CT
LE
SE

EXIT

2. Push up and hold the Adjustable Tilt Foot Lever on the front of
the projector to extend the adjustable tilt foot.
2

3. Lower the front of the projector to the desired height.

Adjustable Tilt
Foot Lever

4. Release the Adjustable Tilt Foot Lever to lock the Adjustable tilt
foot.

Adjustable Tilt Foot

The tilt foot can be extended up to 1.8 inch/45 mm.
There is approximately 10 degrees (up) of adjustment for the front of
the projector.
AUT
OAD
J.
SOU

Rotate the rear foot to the desired height in order to square the image
on the projection surface.

LAM
P
STA
TUS

RCE

ENTER

EXIT

ECT

SEL

ME
NU

• Do not use the tilt-foot for purposes other than originally intended.
Misuses such as using the tilt foot to carry or hang (from the wall or
ceiling) the projector can cause damage to the projector.

CAUTION:
4

Adjusting the left and right tilt of an image [Rear foot]
1. Remove the spacer (black rubber) from the rear foot.
S
CU
FO

Keep the spacer for future use.
2. Rotate the rear foot.

ENTER

SEL
ECT

EXIT

The rear foot can be extended up to 0.4 inch/10 mm. Rotating the rear
foot allows the projector to be placed horizontally.

SOU
RCE
AUT
OAD

NOTE:
• Do not extend the rear foot beyond its height limit (0.4 inch/10 mm). Doing so
may cause the rear foot to come out of the projector.
• After using the projector, attach the spacer to the rear foot.

LAM
P
STA
TUS

Rear foot

Spacer (black
rubber)

S
CU
FO

ENTER

SEL

ECT

EXIT

SOU
RCE
AUT

OAD
J.

LAM
P
STA
TUS

Down

3. Projecting an Image (Basic Operation)
Zoom

C
R
U

U
A

A
TO

J.
D

P
M

TU
TA

Use the ZOOM lever to adjust the image size on the screen.

S
U

U
N

ENTER

T
C

EXIT

Zoom Lever

FOCUS

Focus

J.
D

C
R
U

U
A

A
TO

P
M

TU
TA
S

Use the FOCUS ring to obtain the best focus.

Focus Ring

ENTER

S
U

U
N

T
C

EXIT

FOCUS

3. Projecting an Image (Basic Operation)

 Correcting Keystone Distortion
Correcting Keystone Distortion
If the screen is tilted vertically, keystone distortion becomes large. Proceed with the following
steps to correct keystone distortion

NOTE:
• The Keystone correction can cause an image to be slightly blurred because the correction is made electronically.
• The Keystone correction range can be made narrower, depending on a signal or its aspect ratio selection.

Adjusting with buttons on the cabinet
1. Press the SELECT  or  button with no menus displayed
The keystone bar will be displayed.
MENU

SELECT

EX
I

TE
EN

LAMP
STATUS

2. Use the SELECT  or  to correct the keystone distortion.

SOURCE

AUTO ADJ.

The keystone bar will be closed after a period of time.
3. Press the ENTER button.
The keystone bar will be closed.
NOTE: When the menu is displayed, the above operation is not available. When the menu is displayed, press the MENU button to
close the menu and start the Keystone correction.
From the menu, select [SETUP] → [GENERAL] → [KEYSTONE]. The changes can be saved with [KEYSTONE SAVE]. (→page
30,57)

3. Projecting an Image (Basic Operation)
Adjusting with the Remote Control
1. Press the MENU button.
The menu will be displayed.
2. Press the SELECT  button to select [SETUP] and press the ENTER button.

The [GENERAL] screen will be displayed.
3. Press the SELECT  button to select [KEYSTONE].

4. Press the SELECT  or  button.
Adjust so that the image is rectangular.

5. Press the MENU button.
The menu will be closed.
NOTE: The Keystone correction can cause an image to be slightly blurred because the correction is made electronically.
TIP: The changes can be saved with [KEYSTONE SAVE]. (→page 30,57)

3. Projecting an Image (Basic Operation)
Adjusting with the Auto Keystone Function
The Auto Keystone correction feature will correct the vertical distortion of a projected image on the screen. No special
operation required. Just put the projector on a flat surface.
TIP: Even when the menu setting for [AUTO KEYSTONE] is turned on, [KEYSTONE] can be adjusted manually.
To turn on [AUTO KEYSTONE], proceed the following steps.
1. Press the MENU button
The menu will be displayed.
2. Press the SELECT  button to select [SETUP] and press the ENTER button.
The [GENERAL] screen will be highlighted.
3. Press the SELECT  button.
The [AUTO KEYSTONE] will be highlighted.

4. Press the ENTER button to display the [AUTO KEYSTONE] screen.
5. Press the SELECT  or  button to select [ON] and press the ENTER button.
6. Press the MENU button.
The menu will be closed.
NOTE:
• Vertical distortions between offset angles of +/- 30 degrees can be corrected.
The range of keystone correction is not the maximum tilt angle of projector.
• The Auto Keystone correction will take effect in 2 seconds after changing the projection angle during projection.
• The left and right (horizontal) keystone correction is not available.
Place the projector so that the lens surface is parallel to the screen.
The rear feet of the projector can be adjusted to level the projector.
NOTE:
• Auto and Manual Keystone correction angle could be less than 30 degrees depending on the signal and/or aspect ratios.
• Using keystone correction can cause the image to be slightly blurred because the correction is made electronically.
TIP: If you have one of the following conditions, the projector’s Auto Keystone may not be performed correctly.
• The screen is tilted
• The room temperature is too high or too low
• The optical zoom is maximized or minimized

3. Projecting an Image (Basic Operation)

 Optimizing Computer Signal Automatically
Adjusting the Image Using Auto Adjust
Optimizing a computer image automatically.
Press the AUTO ADJ. button to optimize a computer image automatically.
This adjustment may be necessary when you connect your computer for the first time.
[Poor picture]
MENU
L-CLICK

R-CLICK

VIDEO

COMPUTER AUTO ADJ.

MOUSE

SELECT

S-VIDEO

LAMP MODE

2
ASPECT

HELP

PICTURE

FREEZE

EX
I

TE
EN

VOLUME

LAMP
STATUS
SOURCE

AUTO ADJ.

[Normal picture]

NOTE:
Some signals may take time to display or may not be displayed correctly.
• The Auto Adjust function does not work for component, video, and DVI digital signals.
• If the Auto Adjust operation cannot optimize the computer signal, try to adjust [HORIZONTAL], [VERTICAL], [CLOCK], and [PHASE]
manually. (→page 52,53)

 Turning Up or Down Volume
L-CLICK

Sound level from the speaker can be adjusted.

R-CLICK
MOUSE

VIDEO

COMPUTER AUTO ADJ.

Increase volume

S-VIDEO

LAMP MODE

2
VOLUME

ASPECT

HELP

PICTURE

FREEZE

Decrease volume

TIP: When no menus appear, the SELECT  and  buttons on the projector cabinet work as a volume control.
MENU

SELECT

EX
I

TE
EN

LAMP
STATUS
SOURCE

AUTO ADJ.

3. Projecting an Image (Basic Operation)

7 Turning off the Projector
To turn off the projector:
MENU
OFF

ON
POWER

MAGNIFY PIC-MUTE

SELECT

PAGE
UP

DOWN

EX
I

TE
EN

1. First, press the
(POWER) button on the projector
cabinet or the POWER OFF button on the remote control. The [POWER OFF / ARE YOU SURE?] message will
appear.

LAMP
STATUS
SOURCE

2. Secondly, press the ENTER button or press the
(POWER) or the POWER OFF button again.

ENTER

AUTO ADJ.

EXIT

Power On

Fan running

Standby

Steady green
light

Blinking
orange light

Steady
orange light

The power indicator will glow orange. After the projector turns off, the cooling fans keep operating for 30
seconds (Cool-down time).
Immediately after turning on the projector and displaying an image, you cannot turn off the projector for 60
seconds.

C
FO

3. Finally, turn off the Main Power switch. The power indicator will go out.

S
U

ME
NU
SE
LEC
T

ENTER

NOTE: Do not turn off the main power within 10 seconds of making
adjustment or setting changes and closing the menu.
Doing so can cause loss of adjustments and settings.

EXIT

CE
AU

LA
MP
STA
TU
S

CAUTION:
Parts of the projector will become heated during operation. Use caution when picking up the projector immediately
after it has been operating.
CAUTION:
The projector cannot be turned off for 60 seconds after the lamp is turned on and while the POWER indicator is
blinking green. Doing so could cause premature lamp failure.

3. Projecting an Image (Basic Operation)

 After Use
Preparation: Make sure that the projector is turned off.
1. Unplug the power cable.
2. Disconnect any other cables.
3. Retract adjustable tilt foot if extended.
4. Cover the lens with the lens cap.
5. Put the projector and accessories in the supplied soft case.
Place the projector in the soft case with the lens facing upward as shown below. This is to prevent the lens from
damage.
Insert the projector with the lens
facing upward

S
FOCU

SUCOF

T
EXIT

SELEC

LAMP

ENTER

S
SUTATS

PMAL

STATU

TCELES

.JDAOTUA

TI
X
E

UNEM

ADJ.
AUTO
CE
SOUR

ECRUOS

RET
NE

NOTE: When placing the projector in the soft case, retract the tilt foot and the rear feet. Failure to do so may case damage to the
projector.
CAUTION:
Use caution when putting the projector in the soft case immediately after the projector has been operating. The
projector cabinet is hot.

4. Convenient Features
1 Turning off the Image and Sound
Press the PIC-MUTE button to turn off the image and sound for a short
period of time. Press again to restore the image and sound.

OFF

ON
POWER

MAGNIFY PIC-MUTE

PAGE
UP

SELECT

NOTE:
• Even though the image is turned off, the menu still remains on the screen.
• Sound from the AUDIO OUT jack (Stereo mini) can be turned off.

2 Freezing a Picture

DOWN

ENTER

EXIT

L-CLICK

R-CLICK

VIDEO

COMPUTER AUTO ADJ.

MOUSE

Press the FREEZE button to freeze a picture. Press again to resume
motion.

1
S-VIDEO

LAMP MODE

2
VOLUME

ASPECT

HELP

PICTURE

FREEZE

NOTE: The image is frozen but the original video is still playing back.

 Enlarging a Picture
You can enlarge the picture up to four times.
NOTE: The maximum magnification may be less than four times depending on
the signal.
To do so:
1. Press the MAGNIFY (+) button to magnify the picture.
To move the magnified image, use the SELECT ,, or button.
OFF

ON
POWER

MAGNIFY PIC-MUTE

PAGE
UP

DOWN

ENTER

EXIT

OFF

ON
POWER

MAGNIFY PIC-MUTE

PAGE
UP

DOWN

ENTER

EXIT

SOURCE

PIC-MUTE

4. Convenient Features
2. Press the SELECT  button.
The area of the magnified image will be moved

3. Press the MAGNIFY (-) button.

OFF

Each time the MAGNIFY (-) button is pressed, the image is reduced.

ON
POWER

MAGNIFY PIC-MUTE

PAGE
UP

NOTE:
• The image will be enlarged or reduced at the center of the screen.
• Displaying the menu will cancel the current magnification.

DOWN

ENTER

EXIT

 Changing Lamp Mode
This feature enables you to select two brightness modes of the lamp:
Normal and Eco modes. The lamp life can be extended by using the Eco mode.
Lamp Mode

Description

Status of LAMP indicator

NORMAL

This is the default setting (100%
Brightness).

Off

Select this mode to increase the
lamp life (approx. 80% Brightness).

Steady Green light

ECO

LAMP
STATUS

To change to the [ECO] mode, do the following:
1. Press the LAMP MODE button on the remote control to display [LAMP MODE] screen.
2. Use the SELECT  or  button to select [ECO] mode.
3. Press the ENTER button.
To change from [ECO] to [NORMAL], Go back to Step 2 and select [NORMAL]. Repeat Step 3.
NOTE:
• The LAMP MODE can be changed by using the menu.
Select [SETUP] → [GENERAL] → [LAMP MODE].
• The lamp life remaining and lamp hours used can be checked in [USAGE TIME]. Select [INFO.] →[USAGE TIME].
• The projector is always in [NORMAL] for one minute after the lamp is turned on and while the POWER indicator is blinking green.
The lamp condition will not be affected even when [LAMP MODE] is changed.
• After a lapse of 3 minutes from when the projector displays a blue, black or logo screen, [LAMP MODE] will automatically switch
to [ECO]. The projector will return to the [NORMAL] once a signal is accepted.
• If the projector is overheated in [NORMAL] mode, there may be a case where the [LAMP MODE] automatically changes to [ECO]
mode to protect the projector. When the projector is in [ECO] mode, the picture brightness decreases. When the projector comes
back to normal temperature, the [LAMP MODE] returns to [NORMAL] mode.
Thermometer symbol [ ] indicates the lamp mode is automatically set to [ECO] mode because the internal temperature is too
high.

4. Convenient Features

 Preventing the Unauthorized Use of the Projector [SECURITY]
A keyword can be set for your projector using the Menu to avoid operation by an unauthorized user. When a keyword
is set, turning on the projector will display the Keyword input screen. Unless the correct keyword is entered, the projector cannot project an image.
• The [SECURITY] setting cannot be cancelled by using the [RESET] of the menu.
To enable the Security function:
1. Press the MENU button.
The menu will be displayed.
2. Press the SELECT  button twice to select [SETUP] and press the SELECT  button or the ENTER button
to select [GENERAL].
3. Press the SELECT  button to select [INSTALLATION].
4. Press the SELECT  button three times to select [SECURITY] and press the ENTER button.

The OFF/ON menu will be displayed.
5. Press the SELECT  button to select [ON] and press the ENTER button.

The [SECURITY KEYWORD] screen will be displayed.
6. Type in a combination of the four SELECT  buttons and press the ENTER button.
NOTE: A keyword must be 4 to 10 digits in length.

The [CONFIRM KEYWORD] screen will be displayed.

4. Convenient Features
7. Type in the same combination of SELECT  buttons and press the ENTER button.

The confirmation screen will be displayed.
8. Select [YES] and press the ENTER button.

The SECURITY function has been enabled.
To turn on the projector when [SECURITY] is enabled:
When the SECURITY function is enabled and the projector is turned on, the projector will display a blue background.
To display an image at this time, press the MENU button to display the Keyword input screen.

Type in the correct keyword and press the ENTER button. The projector will display an image.

NOTE: The security disable mode is maintained until the main power is turned off or unplugging the power cable.

4. Convenient Features
To disable the SECURITY function:
1. Press the MENU button.
The menu will be displayed.
2. Select [SETUP] → [INSTALLATION] → [SECURITY] and press the ENTER button.

The OFF/ON menu will be displayed.
3. Select [OFF] and press the ENTER button.

The KEYWORD CONFIRMATION screen will be displayed.

4. Type in your keyword and press the ENTER button.
When the correct keyword is entered, the SECURITY function will be disabled.
NOTE: If you forget your keyword, contact your dealer. Your dealer will provide you with your keyword in exchange for your request
code. Your request code is displayed in the Keyword Confirmation screen. In this example [K992-45L8-JNGJ-4XU9-1YAT-EEA2] is
a request code.

4. Convenient Features

 Using the Optional Remote Mouse Receiver (NP01MR)
The optional remote mouse receiver enables you to operate your computer’s mouse functions from the remote control.
It is a great convenience for clicking through your computer-generated presentations.

Connecting the remote mouse receiver to your computer
If you wish to use the remote mouse function, connect the mouse receiver and computer.
The mouse receiver can be connected directly to the computer’s USB port (type A).
NOTE: Depending on the type of connection or OS installed on your computer, you may have to restart your computer or change
your computer settings.
Computer

Remote mouse receiver

To USB port of PC or Macintosh

When operating a computer via the remote mouse receiver
7m/22 feet
30˚
30˚

Remote sensor on the
remote mouse receiver

When connecting using the USB terminal
For PC, the mouse receiver can only be used with a Windows 98/Me/XP*, Windows 2000, Windows Vista, or Mac OS
X 10.0.0 or later operating system.
* NOTE: In SP1 or older version of Windows XP, if the mouse cursor will not move correctly, do the following:
Clear the Enhance pointer precision check box underneath the mouse speed slider in the Mouse Properties dialog box [Pointer
Options tab].
NOTE: Wait at least 5 seconds after disconnecting the mouse receiver before reconnecting it and vice versa. The computer may not
identify the mouse receiver if it is repeatedly connected and disconnected in rapid intervals.

4. Convenient Features
Operating your computer’s mouse from the remote control
You can operate your computer’s mouse from the remote control.
PAGE UP/DOWN Button: scrolls the viewing area of the window or to move to the previous or next slide in PowerPoint on your computer.
SELECT Buttons: moves the mouse cursor on your computer.
MOUSE L-CLICK Button: works as the mouse left button.
MOUSE R-CLICK Button: works as the mouse right button.
NOTE:
• When you operate the computer using the SELECT  or  button with the menu displayed, both the menu and the mouse
pointer will be affected. Close the menu and perform the mouse operation.
• The PAGE UP and DOWN buttons do not work with PowerPoint for Macintosh.

About Drag Mode:
By pressing the MOUSE L-CLICK or R-CLICK button for 2 or 3 seconds then releasing, the drag mode is set and the
drag operation can be performed simply by pressing the SELECT  button. To drop the item, press the MOUSE
L-CLICK (or R-CLICK) button. To cancel it, press the MOUSE R-CLICK (or L-CLICK) button.
TIP: You can change the Pointer speed on the Mouse Properties dialog box on the Windows. For more information, see the user
documentation or online help supplied with your computer.

4. Convenient Features

7 Network Setting by Using an HTTP Browser
Overview
Connecting the projector to a network allows the Alert Mail setting (→ page 43) and the projector control from a
computer via the network.
To perform the projector control from a web browser, you must have an exclusive application installed on your computer.
The IP address and subnet mask of the projector can be set on the Network Setting screen of the web browser by
using an HTTP server function. Please be sure to use “Microsoft Internet Explorer 6.0” or a higher version for the web
browser. (This device uses “JavaScript” and “Cookies” and the browser should be set to accept these functions. The
setting method will vary depending on the version of browser. Please refer to the help files and the other information
provided in your software.)
Access is gained to the HTTP server function by starting the Web browser on the computer via the network connected
to the projector and enter the following URL.
• Network Setting

http:///index.html

• Alert Mail Setting

http:///lanconfig.html

TIP:
• The default IP address is “192.168.0.10”.
• The exclusive application can be downloaded from our website.
NOTE:
• If the PROJECTOR NETWORK SETTINGS screen does not appear in the web browser, press the Ctrl+F5 keys to refresh your web
browser (or clear the cache).
• The display’s or button’s response can be slowed down or operation may not be accepted depending the settings of your network.
Should this happen, consult your network administrator.
The projector may not respond if its buttons are repeatedly pressed in rapid intervals. Should this happen, wait a moment and
repeat. If you still can’t get any response, turn off and back on the projector.

Preparation Before Use
Connect the projector to a commercially available LAN cable before engaging in browser operations. (→ page 20)
Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and the
setting method. Although the type of proxy server will be a factor, it is possible that items that have actually been set
will not be displayed depending on the effectiveness of the cache, and the contents set from the browser may not be
reflected in operation. It is recommended that a proxy server not be used unless it is unavoidable.

Handling of the Address for Operation via a Browser
Regarding the actual address that is entered for the address or entered to the URL column when operation of the projector is via a browser, the host name can be used as it is when the host name corresponding to the IP address of the
projector has been registered to the domain name server by a network administrator, or the host name corresponding
to the IP address of the projector has been set in the “HOSTS” file of the computer being used.
Example 1:

Example 2:

When the host name of the projector has been set to “pj.nec.co.jp”, access is gained to the network
setting by specifying
http://pj.nec.co.jp/index.html
for the address or the entry column of the URL.
When the IP address of the projector is “192.168.73.1”, access is gained to the mail alert settings by
specifying
http://192.168.73.1/index.html
for the address or the entry column of the URL.

4. Convenient Features
Network Settings
http:// /index.html

DHCP...................................Enabling this option automatically assigns an IP address to the projector from your DHCP server.
Disabling this option allows you to register the IP address or subnet mask number obtained from
your network administrator.
NOTE:
The IP address of the projector is required to change the network setting.
The IP address will not be displayed on the projector’s menu.
Consult your network administrator for the IP address when [ENABLE] is selected for [DHCP].
IP ADDRESS........................Set your IP address of the network connected to the projector when [DISABLE] is selected for
[DHCP].
SUBNET MASK....................Set your subnet mask number of the network connected to the projector when [DISABLE] is selected
for [DHCP].
DEFAULT GATEWAY.................Set your default gateway of the network connected to the projector when [DISABLE] is selected for
[DHCP].
DNS (PRIMARY)..................Set your primary DNS settings of the network connected to the projector.
DNS (SECONDARY)..................Set your secondary DNS settings of the network connected to the projector.
UPDATE...............................Reflect your settings.
NOTE: Close the browser after clicking [UPDATE]. The projector will automatically update your
settings.
TIP: Selecting [NETWORK SETTINGS] for [RESET] from the projector’s menu allows you to return the following items to the factory
default.
[DHCP]: DISABLE
[IP ADDRESS]: 192.168.0.10
[SUBNET MASK]: 255.255.255.0
[DEFAULT GATEWAY]: 192.168.01
*[DNS(PRIMARY)] and [DNS(SECONDARY)] will remain unchanged.

4. Convenient Features
Alert Mail Setting
http:// /lanconfig.html

This option notifies your computer of an error message via e-mail when using wired LAN. An error message notification
will be sent when the projector lamp has reached the end of its usable life or an error occurs in the projector.
HOST NAME ............................. Type in the hostname of the network connected to the projector. Up to 60 alphanumeric characters
can be used.
DOMAIN NAME . ....................... Type in the domain name of the network connected to the projector. Up to 60 alphanumeric
characters can be used.
ALERT MAIL.............................. Checking [ENABLE] will turn on the Alert Mail feature.
Checking [DISABLE] will turn off the Alert Mail feature.
SENDER’S ADDRESS................. Type in the senders address. Up to 60 alphanumeric and symbols characters can be used.
SMTP SERVER NAME................ Type in the SMTP server name to be connected to the projector. Up to 60 alphanumeric characters
can be used.
RECIPIENT’S ADDRESS 1 to 3..... Type in your recipient’s address. Up to 60 alphanumeric and symbols characters can be used.
APPLY........................................ Click this button to reflect the above settings
EXECUTE................................... Click this button to send a test mail to check if your settings are correct.
STATUS...................................... A reply to a test mail will be displayed.
NOTE:
• If you execute a test, you may not receive an Alert mail. Should this happen, check if the network settings are correct.
• If you entered an incorrect address in a test, you may not receive an Alert mail. Should this happen, check if the Recipient ’s Address is correct
TIP: The Alert Mail settings will not be affected even when [RESET] is done from the menu.

4. Convenient Features

8 Using the VGA Signal Cable to Operate the Projector
(Virtual Remote)
Overview
The projector supports DDC/CI (Display Data Channel Command Interface) that is a standard interface for bidirectional
communication between display/projector and computer.
The optional utility software “Virtual Remote Tool” designed exclusively for our projector is required to use DDC/CI.
Check with our website.
http://www.nec-pj.com
NOTE: Use the supplied VGA signal cable to connect the COMPUTER 1 IN connector directly with the monitor output connector of
the computer to use Virtual Remote Tool. Using a switcher, scan converter or other cables than the supplied VGA signal cable may
cause failure in signal communication.

5. Using On-Screen Menu
 Using the Menus
NOTE: The on-screen menu may not be displayed correctly while interlaced motion video image is projected.
1. Press the MENU button on the remote control or the projector cabinet to display the menu.

NOTE: The commands such as ENTER, EXIT, ,  in the bottom show available buttons for your operation.
2. Press the SELECT  buttons on the remote control or the projector cabinet to display the submenu.
3. Press the ENTER button on the remote control or the projector cabinet to highlight the top item or the first
tab.
4. Use the SELECT  buttons on the remote control or the projector cabinet to select the item you want to
adjust or set.
You can use the SELECT  buttons on the remote control or the projector cabinet to select the tab you
want.
5. Press the ENTER button on the remote control or the projector cabinet to display the submenu window.
6. Adjust the level or turn the selected item on or off by using the SELECT  buttons on the remote
control or the projector cabinet.
Changes are stored until adjusted again.
7. Repeat steps 2 -6 to adjust an additional item, or press the EXIT button on the remote control or the projector cabinet to quit the menu display.
NOTE: When a menu or message is displayed, several lines of information may be lost, depending on the signal or settings.
8. Press the MENU button to close the menu.
To return to the previous menu, press the EXIT button.

5. Using On-Screen Menu

2 Menu Elements
Tab

Slide bar

Solid triangle

Available buttons
Source

Highlight
Radio button

High Altitude symbol
Thermometer symbol
Key Lock symbol

Off Timer remaining
time

Menu windows or dialog boxes typically have the following elements:
Highlight..............................Indicates the selected menu or item.
Solid triangle.......................Indicates further choices are available. A highlighted triangle indicates the item is active.
Tab.......................................Indicates a group of features in a dialog box. Selecting on any tab brings its page to the front.
Radio button........................Use this round button to select an option in a dialog box.
Source.................................Indicates the currently selected source.
Off Timer remaining time.....Indicates the remaining countdown time when the [OFF TIMER] is preset.
Slide bar..............................Indicates settings or the direction of adjustment.
Key Lock symbol.................Indicates the [CONTROL PANEL LOCK] is enabled.
Thermometer symbol..........Indicates the lamp mode is forcibly set to [ECO] mode because the internal temperature is too
high.
High Altitude symbol...........Indicates the [FAN MODE] is set to [HIGH ALTITUDE] mode.

5. Using On-Screen Menu

3 List of Menu Items
Some menu items are not available depending on the input source.
Menu Item
SOURCE

Default
*
*
*
*
*
*

COMPUTER1
COMPUTER2(DIGITAL)
COMPUTER2(ANALOG)
VIDEO
S-VIDEO
PRESET

Options

1-6

GENERAL
REFERENCE

DETAIL
SETTINGS
PICTURE

ADJUST

IMAGE
OPTIONS

GAMMA
CORRECTION
COLOR
TEMPERATURE
WHITE
BALANCE
CONTRAST R
CONTRAST G
CONTRAST B
BRIGHTNESS
R
BRIGHTNESS
G
BRIGHTNESS
B

DYNAMIC, NATURAL, BLACK DETAIL
*

0
0
0
0
0
0

CONTRAST
BRIGHTNESS
SHARPNESS
COLOR
HUE
RESET
CLOCK
PHASE
HORIZONTAL
VERTICAL
OVERSCAN

*
*
*
*
*
*
*

POSITION
VIDEO FILTER
AUTO KEYSTONE
KEYSTONE
KEYSTONE SAVE

0
*
OFF
0
OFF

WALL COLOR

OFF

LAMP MODE

NORMAL

CLOSED CAPTION

OFF

LANGUAGE

ENGLISH

SETUP

COLOR SELECT
DISPLAY TIME
BACKGROUND
FILTER MESSAGE
ID DISPLAY
ORIENTATION

INSTALLATION

CONTROL PANEL LOCK
SECURITY
COMMUNICATION SPEED
CONTROL ID
CONTROL ID
NUMBER
CONTROL ID

5000, 6500, 7800, 8500, 9300, 10500

ASPECT RATIO

GENERAL

HIGH-BRIGHT, PRESENTATION, VIDEO, MOVIE,
GRAPHIC, sRGB

COLOR
AUTO 45 SEC
BLUE
500[H]
ON
DESKTOP
FRONT
OFF
OFF
19200bps
1
OFF

0[%], 5[%], 10[%]
NP600/NP500/NP400:AUTO, 4:3, 16:9, 15:9, 16:10,
WIDE ZOOM, NATIVE
NP500W: AUTO, 4:3, 16:9, 15:9, 16:10, LETTERBOX,
NATIVE
(Not available on NP500W)
OFF, LESS, MORE
OFF, ON
OFF, ON
OFF, WHITEBOARD, BLACKBOARD, BLACKBOARD
(GRAY), LIGHT YELLOW, LIGHT GREEN, LIGHT
BLUE, SKY BLUE, LIGHT ROSE, PINK
NORMAL, ECO
OFF, CAPTION1, CAPTION2, CAPTION3, CAPTION4,
TEXT1, TEXT2, TEXT3, TEXT4
ENGLISH, DEUTSCH, FRANÇAIS, ITALIANO,
ESPAÑOL, SVENSKA, 日本語
DANSK, PORTUGUÊS, ČEŠTINA, MAGYAR, POLSKI,
NEDERLANDS, SUOMI
NORSK, TÜRKÇE, РУССКИЙ,
, Ελληνικά, 中文,
한국어
COLOR, MONOCHROME
MANUAL, AUTO 5 SEC, AUTO 15 SEC, AUTO 45 SEC
BLUE, BLACK, LOGO
OFF, 100[H], 200[H], 500[H], 1000[H]
OFF, ON
DESKTOP FRONT, CEILING REAR, DESKTOP REAR,
CEILING FRONT
OFF, ON
OFF, ON
4800bps, 9600bps, 19200bps
1- 254
OFF, ON

* The asterisk (*) indicates that the default setting varies depending on the signal.

5. Using On-Screen Menu
AUTO ADJUST
FAN MODE
COMPUTER1
SIGNAL
SELECT
OPTIONS(1)

SETUP

RESET

VIDEO

AUTO

S-VIDEO

AUTO

DEINTERLACE
BEEP
OFF TIMER
STANDBY MODE
AUTO POWER ON(AC)
AUTO POWER ON(COMP1)
AUTO POWER OFF

NP600/NP500/
NP400: OFF
NP500W: ON
ON
ON
OFF
NORMAL
OFF
OFF
OFF

DEFAULT SOURCE SELECT

LAST

WXGA MODE

OPTIONS(2)

INFO.

COMPUTER2
(ANALOG)

NORMAL
AUTO
RGB/
COMPONENT
RGB/
COMPONENT

LAMP LIFE REMAINING
LAMP HOURS USED
USAGE TIME
FILTER HOURS USED
SOURCE INDEX
HORIZONTAL FREQUENCY
VERTICAL FREQUENCY
SIGNAL TYPE
SOURCE
VIDEO TYPE
SYNC TYPE
SYNC POLARITY
SCAN TYPE
PROJECTOR NAME
WIRED LAN
MAC ADDRESS
PRODUCT
SERIAL NUMBER
FIRMWARE
VERSION
DATA
CONTROL ID (when [CONTROL
ID] is set)
CURRENT SIGNAL
ALL DATA
NETWORK SETTINGS
CLEAR LAMP HOURS
CLEAR FILTER HOURS

OFF, NORMAL, FINE
AUTO, HIGH, HIGH ALTITUDE
RGB/COMPONENT, RGB, COMPONENT
RGB/COMPONENT, RGB, COMPONENT
AUTO, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N,
PAL60, SECAM
AUTO, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N,
PAL60, SECAM
OFF, ON
OFF, ON
OFF, ON
OFF, 0:30, 1:00, 2:00, 4:00, 8:00, 12:00, 16:00
NORMAL, POWER-SAVING
OFF, ON
OFF, ON
OFF, 0:05, 0:10, 0:20, 0:30
LAST, AUTO, COMPUTER1, COMPUTER2(DIGITAL),
COMPUTER2(ANALOG), VIDEO, S-VIDEO

5. Using On-Screen Menu

4 Menu Descriptions & Functions [SOURCE]

COMPUTER1
Selects the computer connected to your COMPUTER 1 IN input connector.
NOTE:
• When the component input signal is connected to the COMPUTER 1 IN connector, select [COMPUTER1].
• The projector will determine if the input signal is RGB or component signal.

COMPUTER2 (DIGITAL & ANALOG)
Selects the computer connected to your COMPUTER 2 IN (DVI-I) connector.

VIDEO
Selects what is connected to your VIDEO input-VCR, DVD player or document camera.

S-VIDEO
Selects what is connected to your S-VIDEO input-VCR or DVD player.
NOTE: A frame may freeze for a brief period of time when a video is played back in fast-forward or fast-rewind with a Video or SVideo source.

5. Using On-Screen Menu

5 Menu Descriptions & Functions [ADJUST]
[PICTURE]

[PRESET]
This function allows you to select optimized settings for your projected image.
You can adjust neutral tint for yellow, cyan or magenta.
There are six factory presets optimized for various types of images. You can also use [DETAIL SETTINGS] to set user
adjustable settings to customize each gamma or color.
Your settings can be stored in [PRESET 1] to [PRESET 6].
HIGH-BRIGHT......... Recommended for use in a brightly lit room.
PRESENTATION...... Recommended for making a presentation using a PowerPoint file.
VIDEO..................... Recommended for typical TV program viewing.
MOVIE.................... Recommended for movies.
GRAPHIC................ Recommended for graphics.
sRGB...................... Standard color values

[DETAIL SETTINGS]

5. Using On-Screen Menu
[GENERAL]
Storing Your Customized Settings [REFERENCE]
This function allows you to store your customized settings in [PRESET 1] to [PRESET 6].
First, select a base preset mode from [REFERENCE], then set [GAMMA CORRECTION] and [COLOR TEMPERATURE].
HIGH-BRIGHT......... Recommended for use in a brightly lit room.
PRESENTATION...... Recommended for making a presentation using a PowerPoint file.
VIDEO..................... Recommended for typical TV program viewing.
MOVIE.................... Recommended for movies.
GRAPHIC................ Recommended for graphics.
sRGB...................... Standard color values.

Selecting Gamma Correction Mode [GAMMA CORRECTION]
Each mode is recommended for:
DYNAMIC............... Creates a high-contrast picture.
NATURAL................ Natural reproduction of the picture.
BLACK DETAIL........ Emphasizes detail in dark areas of the picture.

Adjusting Color Temperature [COLOR TEMPERATURE]
This option allows you to select the color temperature of your choice.
NOTE: When [PRESENTATION] or [HIGH-BRIGHT] is selected in [REFERENCE], this function is not available.

Adjusting White Balance [WHITE BALANCE]
This allows you to adjust the white balance. Contrast for each color (RGB) to adjust the white level of the screen;
Brightness for each color (RGB) is used to adjust the black level of the screen.

[CONTRAST]
Adjusts the intensity of the image according to the incoming signal.

[BRIGHTNESS]
Adjusts the brightness level or the back raster intensity.

[SHARPNESS]
Controls the detail of the image.

[COLOR]
Increases or decreases the color saturation level.

[HUE]
Varies the color level from +/- green to +/-blue. The red level is used as reference.
Input signal
Computer (RGB DIGITAL)
Computer (RGB ANALOG)
Component
Video, S-Video

CONTRAST
Yes
Yes
Yes
Yes

BRIGHTNESS
Yes
Yes
Yes
Yes

SHARPNESS
Yes
Yes
Yes
Yes

Yes=Adjustable, No=Not adjustable, Yes* = depending on the signal

COLOR
No
No
Yes*
Yes

HUE
No
No
Yes*
Yes

5. Using On-Screen Menu
[RESET]
The settings and adjustments for [PICTURE] will be returned to the factory settings with the exception of the following;
Preset numbers and [REFERENCE] within the [PRESET] screen.
The settings and adjustments under [DETAIL SETTINGS] within the [PRESET] screen that are not currently selected
will not be reset.

[IMAGE OPTIONS]

Adjusting Clock and Phase [CLOCK/PHASE]
This allows you to manually adjust CLOCK and PHASE.

CLOCK.................... Use this item to fine tune the computer image or to remove any vertical banding that might appear. This
function adjusts the clock frequencies that eliminate the horizontal banding in the image.
This adjustment may be necessary when you connect your computer for the first time.

PHASE.................... Use this item to adjust the clock phase or to reduce video noise, dot interference or cross talk. (This is
evident when part of your image appears to be shimmering.)
Use [PHASE] only after the [CLOCK] is complete.

5. Using On-Screen Menu
Adjusting Horizontal/Vertical Position [HORIZONTAL/VERTICAL]
Adjusts the image location horizontally and vertically.

- An image can be distorted during the adjustment of [CLOCK] and [PHASE]. This is not malfunction.
- The adjustments for [CLOCK], [PHASE], [HORIZONTAL], and [VERTICAL] will be stored in memory for the
current signal. The next time you project the signal with the same resolution, horizontal and vertical frequency,
its adjustments will be called up and applied.
To delete adjustments stored in memory, from the menu, you select [RESET] → [CURRENT SIGNAL] or [ALL
DATA] and reset the adjustments.

Selecting Overscan Percentage [Overscan]
Select overscan percentage (0%, 5% and 10%) for signal.
Projected image

Overscaned by 10%

NOTE:
• The [0[%]] cannot be selected when VIDEO and S-VIDEO signals are used.
• [OVERSCAN] is not available when [NATIVE] is selected for [ASPECT RATIO].

5. Using On-Screen Menu
Selecting Aspect Ratio [ASPECT RATIO]
The term “aspect ratio” refers to the ratio of width to height of a projected image.
The projector automatically determines the incoming signal and displays it in its appropriate aspect ratio.
• This table shows typical resolutions and aspect ratios that most computers support.
Resolution

Aspect Ratio

VGA

640 x 480

4:3

SVGA

800 x 600

4:3

XGA

1024 x 768

4:3

WXGA

1280 x 768

15:9

WXGA

1280 x 800

16:10

WXGA+

1440 x 900

16:10

SXGA

1280 x 1024

5:4

SXGA+

1400 x 1050

4:3

UXGA

1600 x 1200

4:3

Options

Function

AUTO

The projector will automatically determine the incoming signal and display it in its aspect
ratio. (→ next page)
The projector may erroneously determine the aspect ratio depending on its signal. If this
occurs, select the appropriate aspect ratio from the following.

4:3

The image is displayed in 4:3 aspect ratio.

16:9

The image is displayed in 16:9 aspect ratio.

15:9

The image is displayed in 15:9 aspect ratio.

16:10

The image is displayed in 16:10 aspect ratio.

WIDE ZOOM
(NP600/NP500/NP400)

The image is stretched left and right.
Parts of the displayed image are cropped at the left and right edges and therefore not
visible.

LETTERBOX
(NP500W)

The image of a letterbox signal is stretched equally in the horizontal and vertical directions to fit the screen. Parts of the displayed image are cropped at the top and bottom
edges and therefore not visible.

NATIVE

The projector displays the current image in its true resolution when the incoming computer
signal has a lower resolution than the projector’s native resolution.
[Example 1] When the incoming
signal with the resolution of 800
x 600 is displayed on the NP600/
NP500/NP400:

[Example 2] When the incoming
signal with the resolution of 800 x
600 is displayed on the NP500W:
NOTE:
• When a non-computer signal is displayed, the [NATIVE] is not available.
• When a signal with a higher resolution than the projector’s native resolution is displayed, [NATIVE] is not available.

5. Using On-Screen Menu
Sample image when the appropriate aspect ratio is automatically determined
NP600/NP500/NP400
[Computer signal]
Aspect ratio of incoming signal

4:3

5:4

4:3

Letterbox

16:9

15:9

16:10

Sample image when the appropriate aspect ratio is automatically determined

[Video signal]
Aspect ratio of incoming signal
Sample image when the aspect ratio is automatically determined

Squeeze

NOTE: To display a squeezed signal properly, select [16:9] or [WIDE ZOOM].

NP500W
[Computer signal]
Aspect ratio of incoming signal

4:3

5:4

16:9

15:9

16:10

Sample image when the appropriate aspect ratio is automatically determined

[Video signal]
Aspect ratio of incoming signal
Sample image when the aspect ratio is automatically determined

4:3

Letterbox

Squeeze

NOTE: To display a letterbox signal prop- NOTE: To display a squeezed signal properly, select [LETTERBOX].
erly, select [16:9].

TIP:
• Image position can be adjusted vertically using [POSITION] when the [16:9], [15:9], or [16:10] aspect ratios are selected. (→
next page)
• The term “letterbox” refers to a more landscape-oriented image when compared to a 4:3 image, which is the standard aspect
ratio for a vide source.
The letterbox signal has aspect ratios with the vista size “1.85:1” or cinema scope size “2.35:1” for movie film.
• The term “squeeze” refers to the compressed image of which aspect ratio is converted from 16:9 to 4:3.

5. Using On-Screen Menu
Adjusting the Vertical Position of Image [POSITION] (not available on NP500W)
(only when [16:9], [15:9], or [16:10] is selected for [ASPECT RATIO])
When [16:9], [15:9], or [16:10] is selected in [ASPECT RATIO], the image is displayed with black borders on the top
and bottom.
You can adjust the vertical position from the top to the bottom of the black area.

Selecting Video Filter Level [VIDEO FILTER] (not available for Digital RGB, Video and S-Video)
Select one of the three levels for reducing video noise: [OFF], [LESS] or [MORE].
OFF......................... The low-pass filter is turned off.
LESS....................... The low-pass filter is applied partially.
MORE..................... The low-pass filter is applied fully.
NOTE:
• Selecting [OFF] will give best image quality by way of higher bandwidth. Selecting [LESS] will soften the image and selecting
[MORE] will soften the image more.

5. Using On-Screen Menu

6 Menu Descriptions & Functions [SETUP]
[GENERAL]

Enabling Auto Keystone [AUTO KEYSTONE]
This feature allows the projector to detect its tilt and correct vertical distortion automatically.
To turn on the AUTO KEYSTONE feature, select [ON]. To adjust the KEYSTONE feature manually, select [OFF].

Correcting Vertical Keystone Distortion Manually [KEYSTONE]
You can correct vertical distortion manually. (→ page 28)
TIP: When this option is highlighted, pressing the ENTER button will display its slide bar for adjustment.

Saving Vertical Keystone Correction [KEYSTONE SAVE]
This option enables you to save your current keystone settings.
OFF......................... Does not save current keystone correction settings. It will return your keystone correction settings to
“zero”.
ON.......................... Saves current keystone correction settings
Saving your change once affects all sources. The changes are saved when the projector is turned off.
NOTE: When [AUTO KEYSTONE] is set to [ON], [KEYSTONE SAVE] is not available. Next time you turn on the power, the AUTO
KEYSTONE function will work and the data stored with [KEYSTONE SAVE] will be invalid.

5. Using On-Screen Menu
Using the Wall Color Correction [WALL COLOR]

This function allows for quick adaptive color correction in applications where the screen material is not white.
NOTE: Selecting [WHITEBOARD] reduces lamp brightness.

Setting Lamp Mode to Normal or Eco [LAMP MODE]
This feature enables you to select two brightness modes of the lamp: NORMAL and ECO modes. The lamp life can be
extended by using the ECO mode. Selecting ECO mode decreases fan noise when compared to NORMAL mode.
Lamp Mode

Description

Status of LAMP indicator

NORMAL

This is the Default setting
(100% Brightness).

Off

ECO

Select this mode to increase the lamp life
(NP600/NP500W: approx.70% Brightness/ Steady Green light
NP500/NP400: approx.80% Brightness)

NOTE:
• The [LAMP LIFE REMAINING] and [LAMP HOURS USED] can be checked in [USAGE TIME]. Select [INFO.] → [USAGE TIME].
(→ page 67)
• The projector is always in [NORMAL] for one minute after the lamp is turned on and while the POWER indicator is blinking green.
The lamp condition will not be affected even when [LAMP MODE] is changed.
• If there is no signal for about one minute, the projector will display a blue, black or logo background (depending on setting) and
go into [ECO].
The projector will return to the [NORMAL] mode once a signal is accepted.
• If the projector becomes overheated in [NORMAL] mode because of use in a high-temperature room, there may be a case where
the [LAMP MODE] automatically changes to [ECO] mode to protect the projector. This mode is called “forced ECO mode”. When
the projector is in [ECO] mode, the picture brightness decreases. The LAMP indicator’s steady light indicates the projector is in
[ECO] mode. When the projector comes back to normal temperature, the [LAMP MODE] returns to [NORMAL] mode.
Thermometer symbol [ ] indicates the [LAMP MODE] is automatically set to [ECO] mode because the internal temperature is
too high.

Setting Closed Caption [CLOSED CAPTION]
This option sets several closed caption modes that allow text to be superimposed on the projected image of Video
or S-Video.
OFF......................... This exits the closed caption mode.
CAPTION 1-4.......... Text is superimposed.
TEXT 1-4................. Text is displayed.
NOTE:
The closed caption is not available under the following conditions:
• when messages or menus are displayed.
• when an image is magnified, frozen, or muted.

5. Using On-Screen Menu
Selecting Menu Language [LANGUAGE]
You can choose one of 21 languages for on-screen instructions.
NOTE: Your setting will not be affected even when [RESET] is done from the menu.

[MENU]

Selecting Menu Color [COLOR SELECT]
You can choose between two options for menu color: COLOR and MONOCHROME.

Selecting Menu Display Time [DISPLAY TIME]
This option allows you to select how long the projector waits after the last touch of a button to turn off the menu. The
preset choices are [MANUAL], [AUTO 5 SEC], [AUTO 15 SEC], and [AUTO 45 SEC]. The [AUTO 45 SEC] is the factory preset.

Selecting a Color or Logo for Background [BACKGROUND]
Use this feature to display a blue/black screen or logo when no signal is available. The default background is
[BLUE].
NOTE: Your setting will not be affected even when [RESET] is done from the menu.

Selecting Interval Time for Filter Message [FILTER MESSAGE]
This option allows you to select the time preference between displaying the message for cleaning the filters. Clean
the filter when you get the message “PLEASE CLEAN FILTER.” (→page 70)
Five options are available: OFF, 100[H], 200[H], 500[H], 1000[H]
The default setting is 500[H].
NOTE: Your setting will not be affected even when [RESET] is done from the menu.

Turning ON/OFF Control ID [ID DISPLAY]
ID DISPLAY............ This option turns on or off the ID number which is displayed when the ID SET button on the remote control
is pressed.

5. Using On-Screen Menu
[INSTALLATION]

Selecting Projector Orientation [ORIENTATION]
This reorients your image for your type of projection. The options are: desktop front projection, ceiling rear projection,
desktop rear projection, and ceiling front projection.

DESKTOP FRONT

CEILING REAR

DESKTOP REAR

CEILING FRONT

5. Using On-Screen Menu
Disabling the Cabinet Buttons [CONTROL PANEL LOCK]
This option turns on or off the CONTROL PANEL LOCK function.
NOTE:
• This CONTROL PANEL LOCK does not affect the remote control functions.
• When the control panel is locked, pressing and holding the EXIT button on the projector cabinet for about 10 seconds will change
the setting to [OFF].
TIP: When the [CONTROL PANEL LOCK] is turned on, a key lock icon [

] will be displayed at the bottom right of the menu.

Enabling Security [SECURITY]
This feature turns on or off the SECURITY function.
Unless the correct keyword is entered, the projector cannot project an image. (→ page 36)
NOTE: Your setting will not be affected even when [RESET] is done from the menu.

Selecting Communication Speed [COMMUNICATION SPEED]
This feature sets the baud rate of the PC Control port (D-Sub 9P). It supports data rates from 4800 to 19200 bps. The
default is 19200 bps. Select the appropriate baud rate for your equipment to be connected (depending on the equipment, a lower baud rate may be recommended for long cable runs).
NOTE: Your selected communication speed will not be affected even when [RESET] is done from the menu.

5. Using On-Screen Menu
Setting ID to the Projector [CONTROL ID]
(Available only when the optional remote control NP02RC is used)
You can operate multiple projectors separately and independently with the single remote control that has the CONTROL
ID function. If you assign the same ID to all the projectors, you can conveniently operate all the projectors together
using the single remote control. To do so, you have to assign an ID number to each projector.
CONTROL ID NUMBER........Select a number from 1 to 254 you wish to assign to your projector.
CONTROL ID........................Select [OFF] to turn off the CONTROL ID setting and select [ON] to turn on the CONTROL ID setting.
ID DISPLAY.........................This option turns on or off the ID number which is displayed when the ID SET button on the remote
control is pressed.
NOTE:
• Selecting [ON] for [CONTROL ID] will make the remote control supplied with the projector inoperable. The buttons on the projector
cabinet can be used. Neither can you operate the projector by using the optional remote control NP01RC that does not has the
CONTROL ID function.
1
2
3
• Your setting will not be affected even when [RESET] is done from the menu.
4
5
6
• Pressing and holding the ENTER button on the projector cabinet for 10 seconds will display the menu for canceling the Control
7
8
9
ID.
0
OFF

POWER

COMPUTER

VIDEO

AUTO ADJ.

S-VIDEO COMPONENT HDMI

PIP

VIEWER NETWORK

CLEAR

Assigning or Changing the Control ID
1. Turn on the projector.

EXIT

ENTER
R-CLICK

L-CLICK

2. Press the ID SET button on the remote control (NP02RC).

VOLUME

MAGNIFY

PAGE

The CONTROL ID screen will be displayed.

DOWN

PICTURE

LAMP MODE

ASPECT

AV-MUTE

3D REFORM

FREEZE

ID SET

FOCUS
LENS SHIFT /ZOOM

HELP

If the projector can be operated with the current remote control ID, the [ACTIVE] will be displayed. If the projector
cannot be operated with the current remote control ID, the [INACTIVE] will be displayed. To operate the inactive
projector, assign the control ID used for the projector by using the following procedure (Step 3).
OFF

ON
POWER

3. Press one of numeric keypad buttons while pressing and holding the ID SET button on the remote control
(NP02RC).
COMPUTER

VIDEO

AUTO ADJ.

S-VIDEO COMPONENT HDMI

VIEWER NETWORK

Example:
To assign “3”, press the “3” button on the remote control.
No ID means that all the projectors can be operated together with a single remote
control. To set “No ID”, enter “000” or press the CLEAR button.

PIP

CLEAR

ID
MENU

EXIT

ENTER

TIP: The range of IDs is from 1 to 254.

R-CLICK

L-CLICK

VOLUME

MAGNIFY

PAGE

4. Release the ID SET button.

DOWN

The updated CONTROL ID screen will be displayed.
NOTE: The IDs can be cleared in a few days after the batteries are run down or removed.

PICTURE

LAMP MODE

ASPECT

AV-MUTE

3D REFORM

FREEZE

ID SET

FOCUS
LENS SHIFT /ZOOM

HELP

5. Using On-Screen Menu
[OPTIONS(1)]

Setting Auto Adjust [AUTO ADJUST]
This feature sets the Auto Adjust mode so that the computer signal can be automatically or manually adjusted for
noise and stability. You can automatically make adjustment in two ways: [NORMAL] and [FINE].
OFF......................... The computer signal will not be automatically adjusted. You can manually optimize the computer signal.
NORMAL................. Default setting. The computer signal will be automatically adjusted. Normally select this option.
FINE........................ Select this option if fine adjustment is needed. It takes more time to switch to the source than when
[NORMAL]is selected.

Selecting Fan Mode [FAN MODE]
This option allows you to select three modes for fan speed: Auto mode, High speed mode, and High Altitude mode.
AUTO...................... The built-in fans automatically run at a variable speed according to the internal temperature.
HIGH....................... The built-in fans run at high speed.
HIGH ALTITUDE...... The built-in fans run at a high speed. Select this option when using the projector at altitudes approximately
5500 feet/1600 meters or higher.
When you wish to cool down the temperature inside the projector quickly, select [HIGH].
NOTE:
• It is recommended that you select High speed mode if you use the projector non-stop for consecutive days.
• Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5500 feet/1600 meters or higher.
• Using the projector at altitudes approximately 5500 feet/1600 meters or higher without setting to [HIGH ALTITUDE] can cause
the projector to overheat and the protector could shut down. If this happens, wait a couple minutes and turn on the projector.
• Using the projector at altitudes less than approximately 5500 feet/1600 meters and setting to [HIGH ALTITUDE] can cause the
lamp to overcool, causing the image to flicker. Switch [FAN MODE] to [AUTO].
• Using the projector at altitudes approximately 5500 feet/1600 meters or higher can shorten the life of optical components such
as the lamp.
• Your setting will not be affected even when [RESET] is done from the menu.

5. Using On-Screen Menu
Selecting Signal Format [SIGNAL SELECT]
[COMPUTER1], [COMPUTER2(ANALOG)]
Allows you to choose [COMPUTER1], or [COMPUTER2(ANALOG)] for an RGB source such as a computer, or
[COMPONENT] for a component video source such as a DVD player. Normally select [RGB/COMPONENT] and the
projector automatically detects a component signal. However there may be some component signals that the projector
is unable to detect. If this is the case, select [COMPONENT].
[VIDEO & S-VIDEO System Select]
This feature enables you to select composite video standards automatically or manually.
Normally select [AUTO] and the projector will automatically detect the video standard.
In the case where the projector has difficulty detecting the video standard, select the appropriate video standard from
the menu.
This must be done for VIDEO and S-VIDEO respectively.

Enabling or Disabling WXGA Mode [WXGA MODE]
Selecting [ON] will give priority to a WXGA (1280 x 768) signal in recognizing an input signal.
When [WXGA MODE] is set to [ON], an XGA (1024 x 768) signal may not be recognized on NP600, NP500, or NP400.
In this case, select [OFF].

Enabling the deinterlace [DEINTERLACE]
Turns on or off the deinterlace function for a telecine signal.
OFF......................... Select this option if there is any jitter or artifacts in video.
ON.......................... Default standard setting.
NOTE: This feature is not available for RGB, 480p, 576p and HDTV signals.

Enabling Key Sound and Error Sound [BEEP]
This feature turns on or off the button sound or alarm when the following operations are performed.
- Displaying the main menu
- Switching sources
- Resetting data by using [RESET]
- Pressing POWER ON or POWER OFF button

5. Using On-Screen Menu
[OPTIONS(2)]

Using Off Timer [OFF TIMER]
1. Select your desired time between 30 minutes and 16 hours: OFF, 0:30, 1:00, 2:00, 4:00, 8:00, 12:00, 16:00.
2. Press the ENTER button on the remote control.
3. The remaining time starts counting down.
4. The projector will turn off after the countdown is complete.
NOTE:
• To cancel the preset time, set [OFF] for the preset time or turn off the power.
• When the remaining time reaches 3 minutes before the projector is turned off, the [THE PROJECTOR WILL TURN OFF WITHIN 3
MINUTES] message will be displayed on the bottom of the screen.

Selecting Power-saving in [STANDBY MODE]
The projector has two standby modes: [NORMAL] and [POWER-SAVING].
The POWER-SAVING mode is the mode that allows you to put the projector in the power-saving condition which
consumes less power than the NORMAL mode. The projector is preset for NORMAL mode at the factory.
NORMAL................. Power indicator: Orange light/STATUS indicator: Green light
POWER-SAVING..... Power indicator: Orange light/STATUS indicator: Off
The following connectors, buttons or functions will not work during this mode.
- PC CONTROL port, MONITOR OUT connector, and AUDIO OUT connector
- LAN, Mail Alert, AUTO POWER ON(COMP1) functions
- Buttons other than POWER button on the cabinet
- Buttons other than POWER ON button on the remote control
- Virtual Remote function
NOTE: Your setting will not be affected even when [RESET] is done from the menu.

Enabling Auto Power On [AUTO POWER ON(AC)]
Turns the projector on automatically when the power cable is inserted into an active power outlet. This eliminates the
need to always use the POWER button on the remote control or projector cabinet.

5. Using On-Screen Menu
Turning On the Projector By Applying Computer Signal [AUTO POWER ON(COMP1)]
When the projector is in Standby mode, applying a computer signal from a computer connected to the COMPUTER1
IN input will power on the projector and simultaneously project the computer’s image.
This functionality eliminates the need to always use the POWER button on the remote control or the projector cabinet
to power on the projector.
To use this function, first connect a computer to the projector and the projector to an active AC input.
NOTE:
• Disconnecting a computer signal from the computer will not power off the projector. We recommend using this function in combination of the AUTO POWER OFF function.
• This function will not be available under the following conditions:
- when a component signal is applied to the COMPUTER1 IN connector
- when a Sync on Green RGB signal or composite sync signal is applied
- when [POWER-SAVING] is selected for [STANDBY MODE]

Enabling Power Management [AUTO POWER OFF]
When this option is selected you can enable the projector to automatically turn off (at the selected time: 5min., 10min.,
20min., 30min.) if there is no signal received by any input or if no operation is performed.

Selecting Default Source [DEFAULT SOURCE SELECT]
You can set the projector to default to any one of its inputs each time the projector is turned on.
LAST....................................Sets the projector to default to the previous or last active input each time the projector is turned
on.
AUTO...................................Searches for an active source in order of COMPUTER1 → COMPUTER 2(DIGITAL) → COMPUTER2
(ANALOG) → VIDEO → S-VIDEO → COMPUTER1 and displays the first found source.
COMPUTER1.......................Displays the computer signal from the COMPUTER 1 IN connector every time the projector is turned
on.
COMPUTER2(DIGITAL)........Displays the DVI digital from the COMPUTER 2 IN connector every time the projector is turned
on.
COMPUTER2(ANALOG).......Displays the computer signal from the COMPUTER 2 IN connector every time the projector is turned
on.
VIDEO..................................Displays the Video source from the VIDEO IN connector every time the projector is turned on.
S-VIDEO..............................Displays the Video source from the S-VIDEO IN connector every time the projector is turned on.

5. Using On-Screen Menu

7 Menu Descriptions & Functions [INFO.]
Displays the status of the current signal and lamp usage. This item has four pages. The information included is as
follows:
TIP: Pressing the HELP button on the remote control will show the [INFO.] menu items.

[USAGE TIME]

[LAMP LIFE REMAINING] (%)*
[LAMP HOURS USED] (H)
[FILTER HOURS USED] (H)
* The progress indicator shows the percentage of remaining bulb life.

The value informs you of the amount of lamp usage. When the remaining lamp time reaches 0, the LAMP LIFE
REMAINING bar indicator changes from 0% to 100 Hours and starts counting down.

If the remaining lamp time reaches 0 hours, the projector will not turn on regardless of whether the LAMP MODE
is set to NORMAL or ECO.

• The message to the effect that the lamp or the filters should be replaced will be displayed for one minute when
the projector is turned on and when the POWER button on the projector or the remote control is pressed.

To dismiss this message, press any button on the projector or the remote control.
Lamp life(H)
NORMAL

ECO

3000

4000

Replacement lamp
NP07LP

5. Using On-Screen Menu
[SOURCE]

[SOURCE INDEX]
[HORIZONTAL FREQUENCY]
[SIGNAL TYPE]
[SYNC TYPE]
[SCAN TYPE]

[VERTICAL FREQUENCY]
[VIDEO TYPE]
[SYNC POLARITY]

[WIRED LAN]

[PROJECTOR NAME]
[MAC ADDRESS]

[VERSION]

[PRODUCT]
[SERIAL NUMBER]
[FIRMWARE] Version
[DATA] Version
[CONTROL ID] (when [CONTROL ID] is set)

5. Using On-Screen Menu

8 Menu Descriptions & Functions [RESET]

Returning to Factory Default [RESET]
The RESET feature allows you to change adjustments and settings to the factory preset for a (all) source (s) except
the following:
[CURRENT SIGNAL]
Resets the adjustments for the current signal to the factory preset levels.
The items that can be reset are: [PRESET], [CONTRAST], [BRIGHTNESS], [COLOR], [HUE], [SHARPNESS],
[ASPECT RATIO], [HORIZONTAL], [VERTICAL], [CLOCK], [PHASE], and [OVERSCAN].
[ALL DATA]
Reset all the adjustments and settings for all the signals to the factory preset.
All items can be reset EXCEPT [LANGUAGE], [BACKGROUND], [FILTER MESSAGE], [SECURITY], [COMMUNICATION SPEED], [CONTROL ID], [STANDBY MODE], [FAN MODE], [LAMP LIFE REMAINING], [LAMP HOURS
USED], [FILTER HOURS USED], and [NETWORK SETTINGS].
To reset the lamp usage time, see “Clearing Lamp Hour Meter [CLEAR LAMP HOURS]” below.

Clearing Networking Settings [NETWORK SETTINGS]
Returns [DHCP], [IP ADDRESS], [SUBNET MASK], and [GATEWAY] to the default settings.

Clearing Lamp Hour Meter [CLEAR LAMP HOURS]
Resets the lamp clock back to zero. Selecting this option displays submenu for a confirmation. Select [YES] and press
the ENTER button.
NOTE: Elapsed time of the lamp use will not be affected even when [RESET] is done from the menu.
NOTE: The projector will turn off and go into standby mode when you continue to use the projector for another 100 hours after the
lamp has reached the end of its life. In this condition you cannot clear the lamp hour meter on the menu. If this happens, press the
HELP button on the remote control for 10 seconds to reset the lamp clock back to zero. Do this only after replacing the lamp.

Clearing the Filter Usage Hours [CLEAR FILTER HOURS]
Resets the filter usage back to zero. Selecting this option displays submenu for a confirmation. Select [YES] and press
the ENTER button.
NOTE: Elapsed time of the filter use will not be affected even when [RESET] is done from the menu.

6. Maintenance
This section describes the simple maintenance procedures you should follow to clean the filters and replace the lamp.

 Cleaning or Replacing the Filters
The air-filter sponge keeps dust and dirt from getting inside the projector and should be frequently cleaned. If the filter
is dirty or clogged, your projector may overheat.
NOTE: The message for filter cleaning will be displayed for one minute after the projector is turned on or off.
To cancel the message, press any button on the projector cabinet or the remote control.

CAUTION
• Turn off the projector, turn off the main power switch and unplug the projector before replacing the filters.
• Only clean the outside of the filter cover with a vacuum cleaner.
• Do not attempt to operate the projector without the filter cover.

To clean the air-filter:

EXIT

LA
M
ST P
AT
U
S

EN
U

FO
C

Vacuum the filter-through the filter cover.

SO
U
R

ENTER

To replace the filter (sponge):

LA
M
ST P
AT
US
AU
TO
AD
J.

EXIT

SE
LE
CT

FO
C

1. Remove the filter cover (2 locations) by pushing up on the catch of the cover until you feel it detach.

SO
UR
CE

ENTER

2. Replace two filters.
(1) Gently peel off the filter (sponge) and clean the filter cover.
(2) Attach the new filter to the filter cover.

6. Maintenance
3. Reinstall the new filter cover (2 locations).

LA
M
ST P
AT
US
AU
TO
AD
J.

EXIT

SE
LE
CT

C
U
S

• Insert the filter cover until you feel click.

SO
UR
CE

ENTER

4. Clear the filter hours used.
To reset the filter usage time, from the menu, select [RESET] → [CLEAR FILTER HOURS].
(→page 69 for resetting the filter usage time.)
NOTE: Do not wash the filter with soap and water. Soap and water will damage the filter membrane. Before replacing the filter, remove
dust and dirt from the projector cabinet. Keep out dust and dirt during filter replacement.
NOTE: When you replace the lamp, it is also wise to replace the filter. The filter comes in the same package with your replacement
lamp.

2 Cleaning the Cabinet and the Lens
1. Turn off the projector before cleaning.
2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild detergent. Never use strong
detergents or solvents such as alcohol or thinner.
3. Use a blower or lens paper to clean the lens, and be careful not to scratch or mar the lens.

F
O
C
S
U

TU
TA
S

J.
D

R
U
O

E
C

ENTER

A
TO
U
A

SE
LE
CT

T
C
LE
E
S

U
N
E
M

S
U
C

LA
MP
ST
AT
US

AU
TO
AD

ENTER

EXIT

SO
UR

6. Maintenance

 Replacing the Lamp
When the lamp reaches the end of its life, the LAMP indicator in the cabinet will blink red. Even though the lamp may
still be working, replace the lamp to maintain the optimal projector performance. After replacing the lamp, be sure to
clear the lamp hour meter. (→ page 69)

CAUTION
• DO NOT TOUCH THE LAMP immediately after it has been used. It will be extremely hot. Turn the projector off,
wait 30 seconds, turn off the main power switch and then disconnect the power cable. Allow at least one hour for
the lamp to cool before handling.
• DO NOT REMOVE ANY SCREWS except one lamp cover screw and two lamp housing screws. You could receive
an electric shock.
• Do not break the glass on the lamp housing.

Keep finger prints off the glass surface on the lamp housing. Leaving finger prints on the glass surface might cause
an unwanted shadow and poor picture quality.

• The projector will turn off and go into standby mode when you continue to use the projector for another 100 hours
after the lamp has reached the end of its life. If this happens, be sure to replace the lamp. If you continue to use
the lamp after the lamp reaches the end of its life, the lamp bulb may shatter, and pieces of glass may be scattered
in the lamp case. Do not touch them as the pieces of glass may cause injury. If this happens, contact your NEC
dealer for lamp replacement.
*NOTE: This message will be displayed under the following conditions:
• for one minute after the projector has been powered on
• when the
(POWER) button on the projector cabinet or the POWER OFF button on the remote control is pressed
To turn off the message, press any button on the projector cabinet or the remote control.
To replace the lamp:
Optional lamp and tools needed for replacement:
• Replacement lamp NP07LP

6. Maintenance
1. Remove the lamp cover.
(1) Loosen the lamp cover screw
• The lamp cover screw is not removable.
(2) Push and slide the lamp cover off.

U
C
FO

SE
LE
CT

ENTER

SE
LE
CT

EXIT

UR
CE

AU
TO
AD
J.

LA
MP
ST
AT
US

2. Remove the lamp housing.
(1) Loosen the two screws securing the lamp housing until the phillips screwdriver goes into a freewheeling condition.
• The two screws are not removable.
• There is an interlock on this case to prevent the risk of electrical shock. Do not attempt to circumvent this
interlock.
(2) Remove the lamp housing by holding it.
CAUTION:
Make sure that the lamp housing is cool
enough to before removing it.

S
U

Interlock
ME

NU
SE
LE
CT

ENTER

SE
LE
CT

EXIT

SO
CE
AU

CE
AU
TO

LA
MP
ST
AT
US

6. Maintenance
3. Install a new lamp housing.
(1) Insert a new lamp housing until the lamp housing is plugged into the socket.

CAUTION
Do not use a lamp other than the NEC replacement lamp NP07LP.
Order this from your NEC dealer.
(2) Push the top center of the lamp housing to secure it.
(3) Secure it in place with the two screws.
• Be sure to tighten the screws.
U
C
FO

FO
C

S
U

ENTER

SE
LE
CT

EXIT

SO
UR

UR
CE

CE
AU
TO

AU
TO
AD
J.

LA
MP
ST
AT
US

4. Reattach the lamp cover.
(1) Slide the lamp cover back until it snaps into place.
(2) Tighten the screw to secure the lamp cover.
• Be sure to tighten the screw.

U
C
FO

ENTER

SE
LE
CT

EXIT

SE
LE
CT

EXIT

UR
CE

AU
TO
AD
J.

LA
MP
ST
AT
US

5. Connect the supplied power cable, turn on the Main Power switch and turn on the projector.
6. Finally, select the menu → [RESET] → [CLEAR LAMP HOURS] to reset the lamp usage hours.
NOTE: When you continue to use the projector for another 100 hours after the lamp has reached the end of its life, the projector
cannot turn on and the menu is not displayed.
If this happens, press the HELP button on the remote control for 10 seconds to reset the lamp clock back to zero.
When the lamp time clock is reset to zero, the LAMP indicator goes out.

7. Appendix
 Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.

Indicator Messages
Power Indicator
Indicator Condition
Off
Blinking light

Note
–

0.5 sec On,
0.5 sec Off

The projector is getting ready to turn on.

Wait for a moment.

2.5 sec On,
0.5 sec Off

Off Timer is enabled.

–

0.5 sec On,
0.5 sec Off

The projector is cooling down.

Wait for a moment.

Green

The projector is turned on.

–

Orange

The projector is in Standby.

–

Green

Orange
Steady light

Projector Condition
The main power is off

Status Indicator
Indicator Condition
Off
Blinking light

Steady light

Red

Projector Condition

Note

Normal or Standby ([POWER-SAVING] for
–
[STANDBY MODE])
1 cycle (0.5 sec On, Lamp cover error or lamp housing error
2.5 sec Off)

Replace the lamp cover or lamp
housing correctly.

2 cycle (0.5 sec On, Temperature error
0.5 sec Off)

The projector is overheated. Move the
projector to a cooler location.

3 cycle (0.5 sec On, Power error
0.5 sec Off)

Power unit is not working properly.
Contact your dealer.

4 cycle (0.5 sec On, Fan error
0.5 sec Off)

Fans will not work correctly.

6 cycle (0.5 sec On, Lamp error
0.5 sec Off)

Lamp fails to light. Wait a full minute
and then turn on again.

Green

Re-firing the lamp (The projector is cooling The projector is re-firing.
down.)
Wait for a moment.

Green

Standby ([NORMAL] for [STANDBY MODE]) –

Orange

Cabinet button is locked

You have pressed cabinet button
when Cabinet Button is locked.

Lamp Indicator
Indicator Condition
Off

Projector Condition
Normal

Note
–

Blinking light

Red

Lamp has reached its end of life. Lamp re- Replace the lamp.
placement message will be displayed.

Steady light

Red

Lamp has been used beyond its limit. The Replace the lamp.
projector will not turn on until the lamp is
replaced.
–
Lamp mode is set to Eco mode

Green

Over-Temperature Protection
If the temperature inside the projector rises too high, the over-temperature protector will automatically turn off the lamp
with the STATUS indicator blinking (2-cycle On and Off.)
Should this happen, do the following:
• Unplug the power cable after the cooling fans stop.
• Move the projector to a cooler location if the room where you are presenting is particularly too warm.
• Clean the ventilation holes if they are clogged with dust.
• Wait about 60 minutes until the inside of the projector becomes cool enough.

7. Appendix
Common Problems & Solutions (→ “Power/Status/Lamp Indicator” on page 75.)
Problem

Check These Items

Does not turn on
or shut down

• Check that the power cable is plugged in and that the power button on the projector cabinet or the remote
control is on. (→ pages 21 and 32)
• Ensure that the lamp cover is installed correctly. (→ page 74)
• Check to see if the projector has overheated. If there is insufficient ventilation around the projector or if the
room where you are presenting is particularly warm, move the projector to a cooler location.
• Check to see if the lamp usage exceeds 3100 hours (up to 4100 hours : Eco mode). If so, replace the lamp.
After replacing the lamp, reset the lamp hours used. (→ page 69)
• The lamp may fail to light. Wait a full minute and then turn on the power again.
• Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5500 feet/1600
meters or higher. Using the projector at altitudes approximately 5500 feet/1600 meters or higher without setting
to [HIGH ALTITUDE] can cause the projector to overheat and the projector could shut down. If this happens,
wait a couple minutes and turn on the projector. (→ page 63)
Also when the lamp is turned off, the projector internal temperature is hot. If the power is turned on before
the projector has cooled down, the fan will run a short time before the lamp will turn on.

Will turn off

• Ensure that the [AUTO POWER OFF] or [OFF TIMER] is off. (→ page 65,66)

No picture

• Use the COMPUTER1, the COMPUTER2, the VIDEO or the S-VIDEO button on the remote control to select
your source (Computer, Video or S-Video). (→ page 24) If there is still no picture, press the button again.
• Ensure your cables are connected properly.
• Use menus to adjust the brightness and contrast. (→ page 51)
• Remove the lens cap.
• Reset the settings or adjustments to factory preset levels using the [RESET] in the Menu. (→ page 69)
• Enter your registered keyword if the Security function is enabled. (→ page 36)
• Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning
on the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector
before being powered up.
* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver
or power management software.
• See also the next page.

Picture suddenly
becomes dark

• Check if the projector is in the Forced ECO mode because of too high ambient temperature. If this is the case,
lower the internal temperature of the projector by selecting [HIGH] for [FAN MODE]. (→ page 63)

Color tone or hue is
unusual

• Check if an appropriate color is selected in [WALL COLOR]. If so, select an appropriate option. (→ page 58)
• Adjust [HUE] in [PICTURE]. (→ page 51)

Image isn’t square to
the screen

• Reposition the projector to improve its angle to the screen. (→ page 25)
• Use the Keystone correction function to correct the trapezoid distortion. (→ page 28)

Picture is blurred

• Adjust the focus. (→ page 27)
• Reposition the projector to improve its angle to the screen. (→ page 25)
• Ensure that the distance between the projector and screen is within the adjustment range of the lens.
(→ page 11)
• Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.
Should this happen, let the projector stand until there is no condensation on the lens.

Flicker appears on
screen

• Set [FAN MODE] to other than [HIGH ALTITUDE] mode when using the projector at altitudes approximately 5500 feet/1600
meters or lower. Using the projector at altitudes less than approximately 5500 feet/1600 meters and setting to [HIGH
ALTITUDE] can cause the lamp to overcool, causing the image to flicker. Switch [FAN MODE] to [AUTO]. (→ page 63)

Image is scrolling
vertically, horizontally
or both

• Use the COMPUTER1, the COMPUTER2, the VIDEO or the S-VIDEO button on the remote control to select
your source (Computer, Video or S-Video). (→ page 24)
• Adjust the computer image manually with the Horizontal/Vertical in the [IMAGE OPTIONS]. (→ page 53)

Remote control does
not work

• Install new batteries.(→ page 8)
• Make sure there are no obstacles between you and the projector.
• Stand within 22 feet (7 m) of the projector. (→ page 8)

Indicator is lit or blinking

• See the POWER/STATUS/LAMP Indicator. (→ page 75)

Cross color in RGB
mode

• Press the AUTO ADJ. button on the projector cabinet or the remote control. (→ page 31)
• Adjust the computer image manually with [CLOCK]/[PHASE] in [IMAGE OPTIONS] in the menu. (→ page 52)

For more information contact your dealer.

7. Appendix
If there is no picture, or the picture is not displayed correctly.
• Power on process for the projector and the PC.

Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on
the power to the notebook PC.

In most cases the output signal from the notebook PC is not turned on unless connected to the projector before
being powered up.
NOTE: You can check the horizontal frequency of the current signal in the projector’s menu under Information. If it reads “0kHz”,
this means there is no signal being output from the computer. (→ page 68 or go to next step)

• Enabling the computer’s external display.

Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector.
When using a PC compatible laptop, a combination of function keys will enable/disable the external display. Usually, the combination of the ‘Fn” key along with one of the 12 function keys gets the external display to come on or
off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through
external display selections.

• Non-standard signal output from the computer

If the output signal from a notebook PC is not an industry standard, the projected image may not be displayed
correctly. Should this happen, deactivate the notebook PC’s LCD screen when the projector display is in use. Each
notebook PC has a different way of deactivate/reactivate the local LCD screens as described in the previous step.
Refer to your computer’s documentation for detailed information.

• Image displayed is incorrect when using a Macintosh

When using a Macintosh with the projector, set the DIPswitch of the Mac adapter (not supplied with the projector)
according to your resolution. After setting, restart your Macintosh for the changes to take affect.

For setting display modes other than those supported by your Macintosh and the projector, changing the DIP switch
on a Mac adapter may bounce an image slightly or may display nothing. Should this happen, set the DIP switch
to the 13” fixed mode and then restart your Macintosh. After that, restore the DIP switches to a displayable mode
and then restart the Macintosh again.
NOTE: A Video Adapter cable manufactured by Apple Computer is needed for a PowerBook which does not have a mini D-Sub
15-pin connector.

• Mirroring on a PowerBook
* When using the projector with a Macintosh PowerBook, output may not be set to 1024 x 768 unless “mirroring”
is off on your PowerBook. Refer to owner’s manual supplied with your Macintosh computer for mirroring.
• Folders or icons are hidden on the Macintosh screen

Folders or icons may not be seen on the screen. Should this happen, select [View] → [Arrange] from the Apple
menu and arrange icons.

7. Appendix

 Specifications
This section provides technical information about projector’s performance.
Model Number
Optical
LCD Panel

Resolution
Lens

Lamp
Light Output**

Contrast Ratio
(full white: full black)
Image Size (Diagonal)
Projection Distance
Projection Angle

NP600/NP500/NP400/NP500W
NP600/NP500/NP400

NP500W

NP600/NP500: 0.63 inch LCD with Micro Lens Array
(Aspect Ratio 4:3)
NP400: 0.63 inch LCD (Aspect Ratio 4:3)
1024 2 768 pixels*
Manual zoom and focus
Zoom Ratio= 1–1.2
F1.7–2.0 f= 19.8–23.7 mm
NP600: 230W AC (168W in ECO Mode)
NP500/NP400: 210W AC (168W ECO Mode)
NP600: 3500 lumens (approx. 70% in ECO Mode)
NP500: 3000 lumens (approx. 80% in ECO Mode)
NP400: 2600 lumens (approx. 80% in ECO Mode)
500:1

0.59 inch LCD with Micro Lens Array
(Aspect Ratio 16:10)
1280 2 800 pixels*
Zoom Ratio= 1–1.2
F1.7–1.9 f= 17.7–21.2 mm
230W AC (168W in ECO Mode)
3000 lumens (approx. 70% in ECO Mode)

21–300 inches/ 0.53 m–7.6 m
29–444 inches/0.7–11.3 m
28–419 inches/0.7–10.6 m
Tele: 7.9°–8.3°/Wide: 9.5°–10.0°
Tele: 7.6°–7.9°/Wide: 9.1°–9.5°
* Effective pixels are more than 99.99%.
** This is the light output value (lumens) when the [PRESET] mode is set to [HIGH-BRIGHT]. If any
other mode is selected as the [PRESET] mode, the light output value may drop slightly.

Electrical
Inputs
Outputs
PC Control
Wired LAN Port
External Control
Color Reproduction
Compatible Signals****

Video Bandwidth
Horizontal Resolution
Scan Rate
Sync Compatibility
Built-in Speaker

1 RGB/Component (D-Sub 15 P), 1 RGB (Digital/Analog, DVI-I 29 P, HDCP*** supported),
1 S-Video (DIN 4 P), 1 Video (RCA), 1 (L/R) RCA Audio, 2 Stereo Mini Audio
1 RGB (D-Sub 15P), 1 Stereo Mini Audio
1 PC Control Port (D-Sub 9P)
RJ-45
RS232, IR, Wired LAN
16.7 million colors simultaneously, Full color
Analog: VGA/SVGA/XGA/WXGA/WXGA+/SXGA/SXGA+/UXGA
480i/480p/576i/576p/720p/1080i
Digital: VGA/SVGA/XGA/WXGA/SXGA
RGB: 80 MHz (Max.)
540 TV lines: NTSC/NTSC4.43/PAL/PAL-M/PAL-N/PAL60
300 TV lines: SECAM
Horizontal: 15 kHz to 100 kHz (RGB: 24 kHz or over)
Vertical: 50 Hz to 120 Hz
Separate Sync / Composite Sync / Sync on G
7W (monaural)
*** What is HDCP/HDCP technology?
HDCP is an acronym for High-bandwidth Digital Content Protection. High bandwidth Digital Content
Protection (HDCP) is a system for preventing illegal copying of video data sent over a Digital Visual
Interface (DVI).
If you are unable to view material via the DVI input, this does not necessarily mean the projector
is not functioning properly. With the implementation of HDCP, there may be cases in which certain
content is protected with HDCP and might not be displayed due to the decision/intention of the HDCP
community (Digital Content Protection, LLC).
**** An image with higher or lower resolution than the projector’s native resolution (NP600/NP500/NP400:
1024 2 768 / NP500W: 1280 2 800) will be displayed with Advanced AccuBlend.

7. Appendix
Power Requirement

Input Current

Power Consumption

NP600/NP500/NP400: 100–240V AC, 50/60Hz
NP600G/NP500G/NP400G: 200–240V AC,
50/60Hz
NP600: 3.8–1.5A
NP500/NP400: 3.5–1.4A
NP600G: 1.8A
NP500G/NP400G: 1.6A
NP600: 325W in Lamp NORMAL Mode
NP500/NP400: 295W in Lamp NORMAL Mode
NP600/NP500/NP400: 240W in Lamp ECO
Mode/11W in STANDBY Mode/3W in POWERSAVING Mode

NP500W: 100–240V AC, 50/60Hz
NP500WG: 200–240V AC, 50/60Hz
NP500W: 3.8–1.5A
NP500WG: 1.8A

325W in Lamp NORMAL Mode/: 240W in Lamp
ECO Mode/11W in STANDBY Mode/3W in POWERSAVING Mode

Mechanical
Installation
Dimensions
Weight
Environmental
Considerations

Regulations

Orientation: Desktop/Front, Desktop/Rear, Ceiling/Front, Ceiling/Rear
12.1" (W) 2 3.7" (H) 2 10.3" (D) /308 mm (W) 2 93.5 mm (H) 2 262 mm (D)
(not including protrusions)
6.57 lbs / 2.98 kg
Operational Temperatures : 41° to 104°F (5° to 40°C),
(ECO mode selected automatically at 95°F to 104°F/35°C to 40°C)
20% to 80% humidity (non-condensing)
Storage Temperatures : 14° to 122°F (-10° to 50°C),
20% to 80% humidity (non-condensing)
UL/C-UL Approved (UL 60950-1, CSA 60950-1)
Meets DOC Canada Class B requirements
Meets FCC Class B requirements
Meets AS/NZS CISPR.22 Class B
Meets EMC Directive (EN55022, EN55024, EN61000-3-2, EN61000-3-3)
Meets Low Voltage Directive (EN60950-1, TÜV GS Approved)

For additional information visit:
US : http://www.necdisplay.com/
Europe : http://www.nec-display-solutions.com/
Global : http://www.nec-pj.com/
For information on our optional accessories, visit our website or see our brochure.
The specifications are subject to change without notice.

7. Appendix

 Cabinet Dimensions

SOURCE

AUTO ADJ.
STATUS

R
TE
EN

LAMP

EX
IT
SELECT

263 (10.4")

FOCUS

Lens center
308 (12.1")
78 (3.1")

76 (3.0")

55.3 (2.2")

108.5 (4.3")

Lens center

Unit: mm (inch)

7. Appendix

 Pin Assignments of D-Sub COMPUTER Input Connector
Mini D-Sub 15 Pin Connector

11 12 13 14 15
7 8 9 10
1 2 3 4 5

Signal Level
Video signal : 0.7Vp-p (Analog)
Sync signal : TTL level

Pin No. RGB Signal (Analog)

YCbCr Signal

Cr
Y
Cb

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15

Red
Green or Sync on Green
Blue
Ground
Ground
Red Ground
Green Ground
Blue Ground
No Connection
Sync Signal Ground
No Connection
Bi-directional DATA (SDA)*
Horizontal Sync or Composite Sync
Vertical Sync
Data Clock*

Cr Ground
Y Ground
Cb Ground

* Only COMPUTER 1 input connector supported.

7. Appendix

 Compatible Input Signal List
Horizontal: 15KHz to 100KHz (RGB: 24KHz or over)
Vertical: 50Hz to 120Hz
Signal
VIDEO

NTSC
PAL
PAL60
SECAM

IBM

Apple Macintosh®

HDTV

(1080i/60)
(1080i/50)

SDTV
DVD

480p
YCbCr
Progressive

Resolution
(Dots)
640 
480
640 
480
640 
480
640 
480
640 
480
640 
480
800 
600
800 
600
800 
600
800 
600
800 
600
1024 
768
1024 
768
1024 
768
1024 
768
1152 
864
1152 
864
1152 
864
1152 
864
1280 
768
1280 
800
1280 
960
1280 
960
1280 
960
1280 
1024
1280 
1024
1280 
1024
1400 
1050
1400 
1050
1440 
900
1600 
1200
1600 
1200
1600 
1200
1600 
1200
640 
480
832 
624
1024 
768
1152 
870
1280 
1024
1280 
1024
1280 
1024
1920 
1080
1920 
1080
1280 
720
720 
480
720 
480
720 
576
720 
480
720 
576

*
*
*
*

*
*
*
*
*
*
*
*
*
*

*
*

Frequency H.
(kHz)
15.7
15.6
15.7
15.6
31.5
31.5
37.9
37.5
39.4
43.3
35.2
37.9
48.1
46.9
53.7
48.4
56.5
60.0
68.7
54.4
64.0
67.5
77.5
47.8
49.7
60.0
75.0
85.9
64.0
80.0
91.2
64.7
65.3
55.9
75.0
81.3
87.5
93.8
35.0
49.7
60.2
68.7
64.3
69.9
78.4
33.8
28.1
45.0
31.5
15.7
15.6
31.5
31.3

Refresh Rate
(Hz)
59.9
50.0
60.0
50.0
59.9
60.0
72.8
75.0
75.0
85.0
56.3
60.3
72.2
75.0
85.1
60.0
70.1
75.0
85.0
60.1
70.0
75.0
85.1
59.9
59.8
60.0
75.0
85.0
60.0
75.0
85.0
60.0
60.0
59.9
60.0
65.0
70.0
75.0
66.7
74.6
74.9
75.1
60.4
65.2
73.7
60.0
50.0
60.0
59.9
59.9
50.0
59.9
50.0

NOTE:
• Images above flagged with “*” are not supported by digital signal.
• An image with higher or lower resolution than the projector’s native resolution (NP600/NP500/NP400: 1024 x 768 / NP500W:
1280 x 800) will be displayed with Advanced AccuBlend.
• Some composite sync signals may not be displayed correctly.
Signals other than those specified in the table above may not be displayed correctly. If this should happen, change the refresh
rate or resolution on your PC. Refer to Display Properties help section of your PC for procedures.

7. Appendix

 PC Control Codes and Cable Connection
PC Control Codes
Function

Code Data

POWER ON

02H

00H

02H

POWER OFF

02H

01H

00H

03H

INPUT SELECT COMPUTER 1

02H

03H

00H

02H

01H

09H

INPUT SELECT COMPUTER 2 (Digital) 02H

03H

00H

02H

01H

1AH

22H

INPUT SELECT COMPUTER 2 (Analog) 02H

03H

00H

02H

01H

02H

0AH

INPUT SELECT VIDEO

02H

03H

00H

02H

01H

06H

0EH

INPUT SELECT S-VIDEO

02H

03H

00H

02H

01H

0BH

13H

PICTURE MUTE ON

02H

10H

00H

12H

PICTURE MUTE OFF

02H

11H

00H

13H

SOUND MUTE ON

02H

12H

00H

14H

SOUND MUTE OFF

02H

13H

00H

15H

NOTE: Contact your local dealer for a full list of the PC Control Codes if needed.

Cable Connection
Communication Protocol
Baud rate..........................................19200 bps
Data length.......................................8 bits
Parity................................................No parity
Stop bit.............................................One bit
X on/off.............................................None
Communications procedure..............Full duplex
NOTE: Depending on the equipment, a lower baud rate may be recommended for long cable runs.

PC Control Connector (D-SUB 9P)
To TxD of PC
To RxD of PC
To GND of PC

2
6

3
7

4
8

5
9
To RTS of PC
To CTS of PC

NOTE 1: Pins 1, 4, 6 and 9 are no used.
NOTE 2: Jumper “Request to Send” and “Clear to Send” together on both ends of the cable to simplify cable connection.
NOTE 3: For long cable runs it is recommended to set communication speed within projector menus to 9600 bps.

7. Appendix

 Troubleshooting Check List
Before contacting your dealer or service personnel, check the following list to be sure repairs are needed also by
referring to the “Troubleshooting” section in your user’s manual. This checklist below will help us solve your problem
more efficiently.
* Print this page and the next page for your check.
Frequency of occurrence  always  sometimes (How often?_____________________)  other (__________________)
Power
No power (POWER indicator does not light green) See also “Status
Indicator (STATUS)”.
Power cable’s plug is fully inserted into the wall outlet.
Main power switch is pressed to the ON position.
Lamp cover is installed correctly .
Lamp Hours Used (lamp operation hours) was cleared after
lamp replacement.
No power even though you press and hold the POWER button
for 1 second.

Shut down during operation.
Power cable’s plug is fully inserted into the wall outlet.
Lamp cover is installed correctly .
[AUTO POWER OFF] is turned off (only models with the [AUTO
POWER OFF] function).
[OFF TIMER] is turned off (only models with the [OFF TIMER]
function).

Video and Audio
No image is displayed from your PC or video equipment to the
projector.
Still no image even though you connect the projector to the PC
first, then start the PC.
Enabling your notebook PC’s signal output to the projector.
• A combination of function keys will enable/disable the external display. Usually, the combination of the “Fn” key along
with one of the 12 function keys turns the external display
on or off.
No image (blue or black background, no display).
Still no image even though you press the AUTO ADJUST
button.
Still no image even though you carry out [RESET] in the
projector’s menu.
Signal cable’s plug is fully inserted into the input connector
A message appears on the screen.
( _____________________________________________ )
The source connected to the projector is active and available.
Still no image even though you adjust the brightness and/or
the contrast.
Input source’s resolution and frequency are supported by the
projector.

Parts of the image are lost.
Still unchanged even though you press the AUTO ADJUST
button.
Still unchanged even though you carry out [RESET] in the
projector’s menu.
Image is shifted in the vertical or horizontal direction.
Horizontal and vertical positions are correctly adjusted on a
computer signal.
Input source’s resolution and frequency are supported by the
projector.
Some pixels are lost.
Image is flickering.
Still unchanged even though you press the AUTO ADJUST
button.
Still unchanged even though you carry out [RESET] in the
projector’s menu.
Image shows flickering or color drift on a computer signal.
Still unchanged even though you change [FAN MODE] from
[HIGH ALTITUDE] to [AUTO].
Image appears blurry or out of focus.
Still unchanged even though you checked the signal’s resolution
on PC and changed it to projector’s native resolution.
Still unchanged even though you adjusted the focus.

Image is too dark.
Remains unchanged even though you adjust the brightness
and/or the contrast.
Image is distorted.
Image appears to be trapezoidal (unchanged even though you
carry out the [KEYSTONE] adjustment).

No sound.
Audio cable is correctly connected to the audio input of the
projector.
Still unchanged even though you adjusted the volume level.
AUDIO OUT is connected to your audio equipment (only models
with the AUDIO OUT connector).

Other
Remote control does not work.
No obstacles between the sensor of the projector and the
remote control.
Projector is placed near a fluorescent light that can disturb the
infrared remote controls.
Batteries are new and are not reversed in installation.

Buttons on the projector cabinet do not work (only models with the
[CONTROL PANEL LOCK] function)
[CONTROL PANEL LOCK] is not turned on or is disabled in
the menu.
Still unchanged even though you press and hold the EXIT button
for a minimum of 10 seconds.

7. Appendix
In the space below please describe your problem in detail.

Information on application and environment where your projector is used
Projector

Installation environment

Model number:

Screen size:

inch

Serial No.:

Screen type:  White matte  Beads  Polarization

Date of purchase:

Lamp operating time (hours):
Lamp Mode:

 Wide angle  High contrast
Throw distance:

 Normal  Eco

feet/inch/m

Orientation:  Ceiling mount  Desktop

Information on input signal:

Power outlet connection:

Horizontal synch frequency [

] kHz

 Connected directly to wall outlet

Vertical synch frequency

] Hz

 Connected to power cord extender or other (the
number of connected equipment______________)

[

Synch polarity

H  (+)  (–)

V  (+)  (–)

Synch type

 Separate  Composite

 Connected to a power cord reel or other (the number
of connected equipment______________)

 Sync on Green

Computer

STATUS Indicator:
Steady light

 Orange  Green

Manufacturer:

Flashing light

[

Model number:

] cycles

Remote control model number:

Notebook PC  / Desktop 
Native resolution:
Refresh rate:
Video adapter:

Projector

Other:

DVD player

Video equipment

Signal cable

VCR, DVD player, Video camera, Video game or other

NEC standard or other manufacturer’s cable?
Model number:

Length:

inch/m

Manufacturer:

Distribution amplifier

Model number:

Model number:
Switcher
Model number:
Adapter
Model number:

7. Appendix

 TravelCare Guide

6) Problems or damage caused by expendable supplies or devices
connected to the product other than those designated by NEC.

TravelCare - a service for international travelers

7) Problems caused by natural consumption, wear or deterioration
of parts under normal usage conditions.

This product is eligible for “TravelCare”, NEC’s unique international
warranty.
Please note that TravelCare coverage differs in part from coverage under
the warranty included with the product.

8) Problems or damage to lamps and other expendable supplies,
included parts or optional parts.
9) Other conditions stipulated in the warranty included with the
product also apply.

Services offered with TravelCare
This warranty allows customers to receive service on their product at the
NEC and NEC-designated service stations in the countries listed herein
when temporarily traveling internationally for business or pleasure.
For details on services offered by the different service stations, please
refer to the “List of TravelCare Outlets” below.

NOTE: The product can be used overseas with voltages indicated in the rating
label on the product by using a power cable suited for the standards and power
source voltage of the country in which the product is being used.

1 Repair services
The product will be repaired and delivered within 10 business days,
not including shipping time.
During the term of warranty, the cost of maintenance parts, labor costs
for repairs and shipping costs within the service station’s coverage
area are covered by the warranty.

This list applies as of July 1, 2008.
For the most up-to-date information, please refer to the websites of the
service stations in the various countries on the List of TravelCare Outlets
or to the NEC website at http://www.nec-pj.com.

List of TravelCare Outlets

In Europe
NEC Europe Ltd. / European Technical Centre
Address:
Unit G, Stafford Park 12, Telford TF3 3BJ, U.K.
Telephone:
+44 1952 237000
Fax Line:
+44 1952 237006
Email Address: AFR@uk.neceur.com
WEB Address: http://www.neceur.com

2 Replacement product rental service
If the customer desires, he or she can rent a replacement product
while the original product is being repaired.
Fee: US$200 for 12 days
This fee must be paid at the local service station in cash or credit
card.
The US$200 rental fee is non-refundable even if the customer rents
it less than 12 days before returning.
The replacement product will be delivered within 3 business days.
If the customer did not return the replacement product within 12 days,
the customer will be charged the price of the unit.
If the customer returned the replacement product in a faulty or damaged condition, the repair cost will be charged to the customer.
Note that this service is not offered in all countries and regions. Please
refer to the “List of TravelCare Outlets”.
In addition, this replacement product rental service is not offered after
the product’s warranty has expired.

(Regions Covered)
EU: Austria*, Belgium*, Bulgaria*, Czech Republic*, Cyprus*,
Denmark*, Estonia*, Finland*, France*, Germany*, Greece*,
Hungary*, Ireland*, Italy*, Latvia*, Lithuania*, Luxembourg*,
Malta*, The Netherlands*, Poland*, Portugal*, Romania*,
Slovakia*, Slovenia*, Spain*, Sweden* and the United
Kingdom*
EEA: Norway*, Iceland and Liechtenstein
In North America
NEC Display Solutions of America, Inc.
Address:
500 Park Boulevard, Suite 1100 Itasca, Illinois
60143, U.S.A.
Telephone:
+1 800 836 0655
Fax Line:
+1 800 356 2415
Email Address: vsd.tech-support@necsam.com
WEB Address: http://www.necdisplay.com/

Term of warranty
1
a. Upon presentation of the warranty or receipt received upon
purchase:

Valid for the term indicated on the warranty or the normal term
of warranty for the country of purchase.

(Regions Covered)
U.S.A. *, Canada*

b. When only the product is brought in:

In Oceania
NEC Australia Pty., Ltd.
Address:
New South Wales;
Sydney
184 Milperra Road, Reversby NSW 2212
Telephone 131 632
Newcastle
120 Parry Street Newcastle West NSW 2302
Telephone 131 632
Victoria;
Melbourne
Unit 1/6 Garden Road, Clayton VIC 3168
Telephone 131 632
Queensland;
Brisbane
Unit 4/305 Montague Road West End QLD 4101
Telephone 131 632
Southport
Shop1 48 Ferry Road Southport QLD 4215
Telephone 131 632
South Australia;
Adelaide
84A Richmond Road, Keswick SA 5035
Telephone 131 632

Valid for a period of within 14 months of the date of manufacture
indicated by the serial number attached to the product.

2 When a product whose term of warranty is expired is brought in:
Repairs will be offered for a fee. In this case the customer is not eligible
for the replacement product rental service.
3 In the following cases, repairs may be charged, even if the product’s
warranty is still in effect:
1) If the term of warranty, model name, serial number and name of
the store of purchase are not indicated on the warranty or have
been altered.
2) Problems or damage caused by dropping or shocks during shipment or movement by the customer or by improper handling by
the customers.
3) Problems or damage caused by improper usage or unwarrantable
alterations or repairs by the customer.
4) Problems or damage caused by fire, salt damage, gas damage,
earthquakes, lightning damage, storm or flood damage or other
natural disasters or such external factors as dust, cigarette
smoke, abnormal voltage, etc.
5) Problems or damage caused by use in hot or humid places, in
vehicles, boats or ships, etc.

7. Appendix
Western Australia;
Perth
45 Sarich Court Osborne Park WA 6017
Telephone 131 632
WEB Address:

Hyosung ITX Co., Ltd.
Address:
1st Fl., Ire B/D. #2, 4Ga, Yangpyeng-Dong,
Youngdeungpo-Gu, Seoul, Korea 150-967
Telephone:
+82 2 2163 4193
Fax Line:
+82 2 2163 4196
Email Address: moneybear@hyosung.com

http://www.nec.com.au

(Regions Covered)
Australia*, New Zealand

(Regions Covered)
South Korea

In Asia and Middle East
NEC Display Solutions, Ltd.
Address:
686-1, Nishioi, Oi-Machi, Ashigarakami-Gun,
Kanagawa 258-0017, Japan
Telephone:
+81 465 85 2369
Fax Line:
+81 465 85 2393
Email Address: support_pjweb@nevt.nec.co.jp
WEB Address: http://www.nec-pj.com

Lenso Communication Co., Ltd.
Address:
292 Lenso House 4, 1st Floor, Srinakarin Road,
Huamark, Bangkapi, Bangkok 10240, Thailand
Telephone:
+66 2 375 2425
Fax Line:
+66 2 375 2434
Email Address: pattara@lenso.com
WEB Address: http://www.lensocom.com/
(Regions Covered)
Thailand

(Regions Covered)
Japan*

ABBA Electronics L.L.C.
Address:
Tariq Bin Ziyad Road, P.O.Box 327, Dubai, United
Arab Emirates
Telephone:
+971 4 371800
Fax Line:
+971 4 364283
Email Address: ABBA@emirates.net.ae

NEC Hong Kong Ltd.
Address:
25/F.,The Metropolis Tower, 10 Metropolis Drive,
Hunghom, Kowloon, Hong Kong
Telephone:
+852 2369 0335
Fax Line:
+852 2795 6618
Email Address: nechksc@nechk.nec.com.hk

esmond_au@nechk.nec.com.hk
WEB Address: http://www.nec.com.hk

(Regions Covered)
United Arab Emirates

(Regions Covered)
Hong Kong
NEC Taiwan Ltd.
Address:
Telephone:
Fax Line:
Email Address:
WEB Address:

Samir Photographic Supplies
Address:
P.O.Box 599, Jeddah 21421, Saudi Arabia
Telephone:
+966 2 6828219
Fax Line:
+966 2 6830820
Email Address: asif@samir-photo.com

7F, No.167, SEC.2, Nan King East Road, Taipei,
Taiwan, R.O.C.
+886 2 8500 1700
+886 2 8500 1420
eric@nec.com.tw
http://www.nec.com.tw

(Regions Covered)
Taiwan
NEC Solutions Asia Pacific Pte. Ltd
Address:
401 Commonwealth Drive, #07-02, Haw Par
Technocentre, Singapore 149598
Telephone:
+65 6 273 8333
Fax Line:
+65 6 274 2226
Email Address: ncare@nec.com.sg
WEB Address: http://www.nec.com.sg/ap

Riyadh
Address:
Telephone:
Fax Line:
Email Address:

P.O.Box 5519, Riyadh 11432, Saudi Arabia
+966 1 4645064
+966 1 4657912
bhimji@samir-photo.com

Alkhobar
Address:
Telephone:
Fax Line:
Email Address:

P.O.Box 238, Alkhobar 31952, Saudi Arabia
+966 3 8942674
+966 3 8948162
chamsedin@samir-photo.com

(Regions Covered)
Saudi Arabia
NOTE: In countries designated with an asterisk(*), replacement product rental

(Regions Covered)
Singapore

service are offered.

NEC Corporation of Malaysia Sdn. Bhd.
Address:
33rd Floor, Menara TA One, 22, Jalan P. Ramlee,
50250 Kuala Lumpur, Malaysia
Telephone:
+6 03 2178 3600 (ISDN)
Fax Line:
+6 03 2178 3789
Email Address: necare@nsm.nec.co.jp
WEB Address: http://www.necarecenter.com
(Regions Covered)
Malaysia

7. Appendix
Date:

P-1/

TO: NEC or NEC’s Authorized Service Station:
FM:

(Company & Name with signature)

Dear Sir (s),
I would like to apply your TravelCare Service Program based on attached registration and qualification sheet and agree with your
following conditions, and also the Service fee will be charged to my credit card account, if I don’t return the Loan units within the
specified period. I also confirm following information is correct. Regards.

Application Sheet for TravelCare Service Program
Country,
product purchased :
User’s Company Name :
User’s Company Address :
Phone No., Fax No. :
User’s Name :
User’s Address :
Phone No., Fax No. :
Local Contact office :
Local Contact office Address :
Phone No., Fax No. :
User’s Model Name :
Date of Purchase :
Serial No. on cabinet :
Problem of units per User :
Required Service :

(1) Repair and Return

(2) Loan unit

(1) Credit Card

(2) Travelers Cheque

Requested period of Loan unit :
Payment method :
In Case of Credit Card :
Card No. w/Valid Date :

(3) Cash

7. Appendix
Condition of your TravelCare Service Program

5. Loan Service Charges and Conditions:
Upon acceptance of this NEC Projector, Customer agrees to assume
liability for this loan unit.

Enduser is requested to understand following condition of TravelCare
Service Program and complete the necessary information on the application sheet.

The current cost of use of this loan unit is US$200 for 12 calendar
days.
If Customer does not return the unit within the 12 calendar days, Customer will be charged the next highest cost up to and including the full
list price to Credit Cards, which price will be informed by NEC Authorized
Service Stations. Please see the attached listing of contacts for each
country to arrange for pickup of the loan unit.

If you return to their country of origin with the loan unit, you will be charged
additional freight to return the unit to the loaning country.

1. Service Options:
There are 3 types of [Service] available. Enduser has to understand
following condition and is required to fill in the Application Sheet.
1) Repair and Return:
The ‘Faulty unit’ is sent or collected from the customer. It is repaired
and returned within 10 days to the customer, excluding transport
time.
There may have a case, repair and return can’t be done by NEC
Authorized Service Station, because of shortage of spare parts due
to same model is not sold in the territory.

Thank you for your understanding of this program.

2) Repair and Return with Loan: (This service is limited to some Service
Stations)
This service is offered to the Enduser, who cannot wait until their unit
is repaired.
The customer can borrow a unit for US$200 up to 12 days. Customer
then sends in inoperable unit to nearest NEC Authorized Service
Station for service. In order to prevent collection problem, Enduser
is required to fill in Application Sheet.
Enduser needs to confirm the availability of the Service to NEC
Authorized Service Stations.
3) Loan Only:
For this service, NEC Authorized Service Station supplies the customer with a loan unit for US$200 up to 12 days. Customer keeps the
inoperable unit and when customer returns home, customer arranges
to have the projector serviced in the home country.
2. Warranty Exclusions:
This program does not apply if the Projector’s serial number has been
defaced, modified or removed.
If, in the judgement of NEC Authorized Service Station or its agent the
defects or failures result from any cause other than fair wear and tear or
NEC neglect, or fault including the following without limitation:
1) Accidents, transportation, neglect, misuse, abuse, water, dust, smoke
or default of or by the Customer its employees or agents or any third
party;
2) Failure or fluctuation of electrical power, electrical circuitry, air conditioning, humidity control or other environmental conditions such as
use it in smoking area;
3) Any fault in the attachments or associated products or components
(whether or not supplied by NEC or its agents which do not form part
of the Product covered by this warranty);
4) Any act of God, fire, flood, war, act of violence or any similar occurrence;
5) Any attempt by any person other than any person authorized by NEC
to adjust, modify, repair, install or service the product.
6) Any Cross-border charges such as, duty, insurance, tax etc.
3. Charges for Warranty Exclusions and Out of Warranty Case:
In case faulty unit is under warranty exclusions case or under Out of
Warranty period, NEC Authorized Service Station will Inform estimation
of actual service cost to the Enduser with reason.
4. Dead on Arrival (DOA):
Enduser must take this issue up with their original supplier in the country
of purchase.
NEC Authorized Service Station will repair the DOA unit as a Warranty
repair, but will not exchange DOA unit with new units.

7N951211

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Page Mode                       : UseOutlines
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Instance ID                     : uuid:4445a684-42d4-4ec2-b7ed-f44170672001
Document ID                     : adobe:docid:indd:1662162c-308e-11dd-9c87-b40b3f134c47
Rendition Class                 : proof:pdf
Derived From Instance ID        : af3476a0-2fb5-11dd-97fe-b28d8092c5f7
Derived From Document ID        : adobe:docid:indd:68cf38a1-2758-11dd-9ce4-fc7ccc8c7ad0
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 200.00, 200.00, 200.00, 72.00, 72.00, 72.00, 200.00, 72.00, 200.00, 200.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 200.00, 200.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 200.00, 200.00, 200.00, 72.00, 72.00, 72.00, 200.00, 72.00, 200.00, 200.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 200.00, 200.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Document ID  : adobe:docid:photoshop:0cfdd314-443d-11dd-9192-fa327ea9404a, uuid:67803F9728E711DDB365F308DE248AC6, uuid:2A9DC6AE37A811DDA54CB167E191BDD0, uuid:FE7181C62F2911DD9861A3463A32333F, uuid:2A9DC6B237A811DDA54CB167E191BDD0, uuid:ACE0A996323B11DDB636FDEE4E9603D4, uuid:FE7181CB2F2911DD9861A3463A32333F, adobe:docid:photoshop:bc70129a-35c5-11dd-924a-e22e777c7eda, adobe:docid:photoshop:bc70129b-35c5-11dd-924a-e22e777c7eda, adobe:docid:photoshop:bc70129b-35c5-11dd-924a-e22e777c7eda, uuid:3251D3182F3711DD9861A3463A32333F, uuid:3251D31D2F3711DD9861A3463A32333F, adobe:docid:photoshop:bc70129a-35c5-11dd-924a-e22e777c7eda, uuid:3251D31F2F3711DD9861A3463A32333F, adobe:docid:photoshop:bc70129d-35c5-11dd-924a-e22e777c7eda, adobe:docid:photoshop:bc70129c-35c5-11dd-924a-e22e777c7eda, uuid:BAE142673A1611DD89C2F87FB0738836, uuid:F8D1BD0737B611DDA54CB167E191BDD0, uuid:F8D1BD0937B611DDA54CB167E191BDD0, adobe:docid:photoshop:7b34f72e-4853-11dd-8ac0-d029e9f23540, uuid:61E393BB2F4E11DD9861A3463A32333F, adobe:docid:photoshop:7b1c5fd1-2fd1-11dd-9675-b7f9cab69300, adobe:docid:photoshop:c39be7f0-2fd0-11dd-9675-b7f9cab69300, adobe:docid:photoshop:7b1c5fce-2fd1-11dd-9675-b7f9cab69300, adobe:docid:photoshop:7b1c5fd4-2fd1-11dd-9675-b7f9cab69300, adobe:docid:photoshop:7b1c5fd7-2fd1-11dd-9675-b7f9cab69300, adobe:docid:photoshop:7e776205-2fd1-11dd-9675-b7f9cab69300, adobe:docid:photoshop:7e776208-2fd1-11dd-9675-b7f9cab69300, adobe:docid:photoshop:bc701298-35c5-11dd-924a-e22e777c7eda, adobe:docid:photoshop:7e77620b-2fd1-11dd-9675-b7f9cab69300, adobe:docid:photoshop:7e77620e-2fd1-11dd-9675-b7f9cab69300, adobe:docid:photoshop:abe4695a-3222-11dd-8fea-acedea8ce516, adobe:docid:photoshop:0dd2a171-3fae-11dd-bcbf-ca98433b447a, adobe:docid:photoshop:0dd2a172-3fae-11dd-bcbf-ca98433b447a, adobe:docid:photoshop:83a8344c-2fd1-11dd-9675-b7f9cab69300, adobe:docid:photoshop:0dd2a173-3fae-11dd-bcbf-ca98433b447a, adobe:docid:photoshop:0dd2a174-3fae-11dd-bcbf-ca98433b447a, adobe:docid:photoshop:83a83455-2fd1-11dd-9675-b7f9cab69300, adobe:docid:photoshop:86c9350f-2fd1-11dd-9675-b7f9cab69300, adobe:docid:photoshop:0dd2a175-3fae-11dd-bcbf-ca98433b447a, uuid:5FD9107B389F11DD94F2AE7B2FAD0710, adobe:docid:photoshop:a9dbe6fe-331e-11dd-8be4-a08462d21a3d, adobe:docid:photoshop:a9dbe6ff-331e-11dd-8be4-a08462d21a3d, adobe:docid:photoshop:7b34f72f-4853-11dd-8ac0-d029e9f23540, adobe:docid:photoshop:7b34f72f-4853-11dd-8ac0-d029e9f23540, adobe:docid:photoshop:7b34f730-4853-11dd-8ac0-d029e9f23540, adobe:docid:photoshop:89c7f058-2fd1-11dd-9675-b7f9cab69300, adobe:docid:photoshop:89c7f05b-2fd1-11dd-9675-b7f9cab69300, adobe:docid:photoshop:7b34f731-4853-11dd-8ac0-d029e9f23540, adobe:docid:photoshop:8d114794-2fd1-11dd-9675-b7f9cab69300, adobe:docid:photoshop:8d114797-2fd1-11dd-9675-b7f9cab69300, adobe:docid:photoshop:8d11479a-2fd1-11dd-9675-b7f9cab69300, adobe:docid:photoshop:89c7f058-2fd1-11dd-9675-b7f9cab69300, uuid:E1AF03CB023C11DD9124859C612D1FCE, adobe:docid:photoshop:8d11479d-2fd1-11dd-9675-b7f9cab69300, adobe:docid:photoshop:917b408d-2fd1-11dd-9675-b7f9cab69300, uuid:A3DC3054026011DD9124859C612D1FCE, adobe:docid:photoshop:7b34f732-4853-11dd-8ac0-d029e9f23540, uuid:76C62DD50E2D11DD8D5FED92244E48B9, uuid:76C62DD50E2D11DD8D5FED92244E48B9, adobe:docid:photoshop:917b4093-2fd1-11dd-9675-b7f9cab69300, adobe:docid:photoshop:917b4096-2fd1-11dd-9675-b7f9cab69300, adobe:docid:photoshop:9576ee9a-2fd1-11dd-9675-b7f9cab69300, adobe:docid:photoshop:9576ee9d-2fd1-11dd-9675-b7f9cab69300, adobe:docid:photoshop:bc701299-35c5-11dd-924a-e22e777c7eda, adobe:docid:photoshop:985ff2a8-2fd1-11dd-9675-b7f9cab69300, adobe:docid:photoshop:985ff2ab-2fd1-11dd-9675-b7f9cab69300, uuid:38817D1F3B0111DDA9EB88FC2A45A932, uuid:1679EF9D2F7911DD9861A3463A32333F
Manifest Reference Instance ID  : uuid:67803F9828E711DDB365F308DE248AC6, uuid:4D62CBDB42CE11DD8850C9F01D5F9B48, uuid:FDB2E7C7386B11DDA275F2E1EEA543D5, uuid:2A9DC6AF37A811DDA54CB167E191BDD0, uuid:2A9DC6B137A811DDA54CB167E191BDD0, uuid:5FD9107D389F11DD94F2AE7B2FAD0710, uuid:ACE0A999323B11DDB636FDEE4E9603D4, uuid:4D62CBDC42CE11DD8850C9F01D5F9B48, uuid:4D62CBDD42CE11DD8850C9F01D5F9B48, uuid:4D62CBDE42CE11DD8850C9F01D5F9B48, uuid:4D62CBDF42CE11DD8850C9F01D5F9B48, uuid:4D62CBE042CE11DD8850C9F01D5F9B48, uuid:4D62CBE142CE11DD8850C9F01D5F9B48, uuid:4D62CBE242CE11DD8850C9F01D5F9B48, uuid:F8D1BD0A37B611DDA54CB167E191BDD0, uuid:E8183E9D322711DDB636FDEE4E9603D4, uuid:E8183E9E322711DDB636FDEE4E9603D4, uuid:E8183E9F322711DDB636FDEE4E9603D4, uuid:E8183EA0322711DDB636FDEE4E9603D4, uuid:F3E3A36837C411DDA54CB167E191BDD0, uuid:F3E3A36937C411DDA54CB167E191BDD0, uuid:F3E3A36A37C411DDA54CB167E191BDD0, uuid:F3E3A36C37C411DDA54CB167E191BDD0, uuid:F3E3A36E37C411DDA54CB167E191BDD0, uuid:F3E3A36D37C411DDA54CB167E191BDD0, uuid:E8183EA1322711DDB636FDEE4E9603D4, uuid:E8183EA3322711DDB636FDEE4E9603D4, uuid:E8183EA2322711DDB636FDEE4E9603D4, uuid:E8183EA5322711DDB636FDEE4E9603D4, uuid:E8183EA4322711DDB636FDEE4E9603D4, uuid:37B94C61485E11DDBE82E87102BAA624, uuid:F3E3A36F37C411DDA54CB167E191BDD0, uuid:88A558B62F6E11DD9861A3463A32333F, uuid:1679EF942F7911DD9861A3463A32333F, uuid:5FD9107C389F11DD94F2AE7B2FAD0710, uuid:E1AF03CC023C11DD9124859C612D1FCE, uuid:A3DC3055026011DD9124859C612D1FCE, uuid:76C62DD60E2D11DD8D5FED92244E48B9, uuid:76C62DD60E2D11DD8D5FED92244E48B9, uuid:98653C7737CA11DDA54CB167E191BDD0, uuid:98653C7837CA11DDA54CB167E191BDD0, uuid:98653C7937CA11DDA54CB167E191BDD0, uuid:98653C7B37CA11DDA54CB167E191BDD0, uuid:98653C7A37CA11DDA54CB167E191BDD0, uuid:98653C7C37CA11DDA54CB167E191BDD0, uuid:4D62CBE342CE11DD8850C9F01D5F9B48, uuid:1679EF9E2F7911DD9861A3463A32333F
Create Date                     : 2008:07:01 17:35:12+09:00
Modify Date                     : 2008:09:08 10:57:55+02:00
Metadata Date                   : 2008:09:08 10:57:55+02:00
Creator Tool                    : Adobe InDesign CS2 (4.0.5)
Format                          : application/pdf
Producer                        : Adobe PDF Library 7.0
Trapped                         : False
Has XFA                         : No
Page Count                      : 99
Page Layout                     : OneColumn
Creator                         : Adobe InDesign CS2 (4.0.5)

EXIF Metadata provided by EXIF.tools

Nec Np400 Users Manual

NP500 to the manual 5d7bc9b5-ca9d-4dd5-8f4c-99014866dcf6

Navigation menu

Versions of this User Manual:

Views

Navigation