Nec Storage Manager Is010 12E Users Manual Messages Handbook

IS010-12E to the manual cb4f0167-b500-4465-8307-9000958f813f

2015-01-24

: Nec Nec-Storage-Manager-Is010-12E-Users-Manual-331203 nec-storage-manager-is010-12e-users-manual-331203 nec pdf

Open the PDF directly: View PDF PDF.
Page Count: 710 [warning: Documents this large are best viewed by clicking the View PDF Link!]

NEC Storage Manager
Messages Handbook
IS010-12E
© NEC Corporation 2001-2004
No part of the contents of this book may be reproduced or
transmitted in any form without permission of NEC Corporation.
The contents of this book may be modified without notice in the future.
Preface
This manual explains messages handled by NEC Storage Manager. The messages are listed in the order of message
IDs. Refer to the “NEC Storage Manager Manual Guide” (IS901) for the overview of the NEC Storage and the
related manuals.
Remarks 1. This manual explains functions implemented by the following program products:
• NEC Storage Manager and NEC Storage BaseProduct
• NEC Storage AccessControl
• NEC Storage PerformanceMonitor
• NEC Storage PerformanceOptimizer
• NEC Storage ReallocationControl
• NEC Storage ReplicationControl
• NEC Storage ReplicationControl/DisasterRecovery
• NEC Storage ReplicationControl SQL Option
2. This manual is applicable to the program products of the following versions:
• NEC Storage Manager Ver3.3
• NEC Storage BaseProduct Ver3.3
• NEC Storage ReplicationControl Ver3.3
• NEC Storage ReplicationControl/DisasterRecovery Ver3.3
• NEC Storage ReplicationControl SQL Option Ver3.2
• NEC Storage SnapControl Ver3.3
3. The NEC Storage Manager is referred to as iSM or Storage Manager in the text of this manual. Also,
the NEC Storage series disk array subsystem is referred to as a disk array.
4. The following descriptions in the text of this manual refer to the corresponding products.
Description Corresponding Product
Storage Manager NEC Storage Manager
BaseProduct NEC Storage BaseProduct
ReplicationControl SQL
Option
NEC Storage ReplicationControl SQL Option
AccessControl NEC Storage AccessControl
DynamicDataReplication NEC Storage DynamicDataReplication
PerformanceMonitor NEC Storage PerformanceMonitor
RemoteDataReplication NEC Storage RemoteDataReplication
NEC Storage RemoteDataReplication/DisasterRecovery
ReplicationControl NEC Storage ReplicationControl
NEC Storage ReplicationControl/DisasterRecovery
SnapControl NEC Storage SnapControl
5. The following descriptions in the text of this manual refer to the corresponding manuals.
Description Corresponding Manual
User's Manual (UNIX) NEC Storage Manager User's Manual (UNIX) (IS001)
User's Manual NEC Storage Manager User's Manual (IS004)
Data Replication User's Manual
(Function Guide)
NEC Storage Data Replication User's Manual
(Function Guide) (IS015)
Data Replication User's Manual
(Installation and Operation Guide for
Windows) (IS016)
NEC Storage Data Replication User's Manual
(Installation and Operation Guide for Windows) (IS016)
Data Replication Command Reference NEC Storage Data Replication Command Reference (IS021)
6. The term “Microsoft SQL Server 2000” in this text refers to as either Microsoft SQL Server 2000
Enterprise Edition or the Microsoft SQL Server 2000 Standard Edition.
7. Trademarks and registered trademarks
• HP-UX is a registered trademark of Hewlett-Packard Co. in the United States.
• UNIX is a registered trademark of The Open Group in the United States and other countries.
• Microsoft® and Windows® are trademarks or registered trademarks of Microsoft Corporation in the
United States and other countries.
• Solaris is a trademark or a registered trademark of Sun Microsystems, Inc. in the United States and
other countries.
• Linux is a trademark or registered trademark of Mr. Linus Torvalds in the United States and other
countries.
Other product names and company names, etc. are registered trademarks or trademarks of the
associated companies.
The First Edition in May 2002
The Twelfth Edition in November 2004
i
Contents
Chapter 1 Messages and Output Destinations ..................................................................................................................1
1.1 Message Classification ................................................................................................................................................3
1.2 Message Output Destinations ......................................................................................................................................4
1.3 Message Output Format ..............................................................................................................................................6
Chapter 2 Message List .......................................................................................................................................................8
2.1 Interpretation of Message List.....................................................................................................................................8
2.2 Message List................................................................................................................................................................9
Appendix A Message Output Destination List .................................................................................................................634
Appendix B Changed Message List...................................................................................................................................673
ii
This page is intentionally left blank.
Chapter 1 Messages and Output Destinations
1
Chapter 1 Messages and Output
Destinations
The Storage Manager outputs the information, which is required for maintenance and operation of a disk array and
the Storage Manager, to log files of the console/terminal and the management server. The log files to which a
message is output are syslog, event log, and operation log. The message describes information that indicates
events to be reported to an administrator, such as system state transition, fault and error detection, and command
input results.
The ReplicationControl outputs the operation information of data replication in a message format, to the log files
of the console/terminal and the business server. The message is output to syslog, event log, and operation log.
The message describes the information for checking operating conditions, such as command execution results, and
fault and error detection information, etc.
If ESMPRO Agent has been installed in the management server on which the Storage Manager has started,
messages are output to ESMPRO Manager.
Figure 1-1 shows an overview of message output.
Chapter 1 Messages and Output Destinations
2
Business
server
Management server
Storage Manager
Console/Terminal
Disk array
Output to syslog (UNIX) or event log
(Windows)
Output to console/terminal
Syslog or
event log
Operation log
Output to syslog (UNIX) or even
t
log (Windows)
Output to console/terminal
ReplicationControl
Syslog or
event log
Operation log
Output to ESMPRO Manager when ESMPRO
Agent installed (only for Windows)
Figure 1-1 Overview of Message Output
Chapter 1 Messages and Output Destinations
3
1
1
1.
.
.1
1
1
M
M
Me
e
es
s
ss
s
sa
a
ag
g
ge
e
e
C
C
Cl
l
la
a
as
s
ss
s
si
i
if
f
fi
i
ic
c
ca
a
at
t
ti
i
io
o
on
n
n
A message classification is assigned to a message, according to its level of urgency. Messages are
classified into the following four classifications, in the order of urgency: “ERROR”, “WARNING”,
“NOTICE”, and “INFO”. A message classification is also referred to as a message level.
Meanings of the messages are as follows:
y ERROR: Error message
This message indicates an error that has a critical effect to the functions, and prompt recovery by an
administrator is required. An administrator must troubleshoot and recover the system promptly.
y WARNING: Warning message
This message indicates an event that requires attention regarding the system operations, though the
event does not necessarily lead to the system down immediately. An administrator must remove the
cause of the event and take measures to operate the system normally.
y NOTICE: Notifying message
This message notifies the state of internal processes. Although the event notified by the message
does not have any effect on the main functions of disk arrays, an administrator must take appropriate
measures as necessary.
y INFO: Information message
This message indicates operating information. No measures are required.
Chapter 1 Messages and Output Destinations
4
1
1
1.
.
.2
2
2
M
M
Me
e
es
s
ss
s
sa
a
ag
g
ge
e
e
O
O
Ou
u
ut
t
tp
p
pu
u
ut
t
t
D
D
De
e
es
s
st
t
ti
i
in
n
na
a
at
t
ti
i
io
o
on
n
ns
s
s
The output destinations of messages depend on functions and OS to be used. Output destinations are
the console/terminal, operation log, syslog, event log, and ESMPRO Manager. Message output
destinations are described as follows:
y Console/Terminal
A console is a monitoring terminal that is directly connected to the monitoring server of the iSM.
On the other hand, a terminal is a client terminal that is connected to the monitoring server via telnet,
etc. When a command is issued from the iSM or the ReplicationControl, a message indicating
execution result is displayed on the console or the terminal where the command is executed.
y Operation log
Operation log, which is output on UNIX and Windows, records the messages output from the iSM or
the ReplicationControl only. During the operation of iSM client, the information output to the
operation log is also displayed on the message display area of the state monitor screen. Operation
logs are output as the following directory/file names by default.
(1) Storage Manager operation log
UNIX system:
/opt/iSMsvr/etc/log/iSM_Log.log
Windows system:
<Installation directory>\iSMsvr\etc\log\iSM_Log.log
(2) ReplicationControl operation log
HP-UX system:
/opt/iSMrpl/etc/*.log
/opt/iSMvol/etc/*.log
Solaris system:
/opt/NECiSMrpl/etc/*.log
/opt/NECiSMvol/etc/*.log
Windows system:
<Installation directory>\iSMrpl\etc\trace\*.log
<Installation directory>\iSMvol\etc\trace\*.log
Chapter 1 Messages and Output Destinations
5
y syslog
This is output on UNIX system. Together with the messages output by UNIX, the messages output
from iSM and ReplicationControl are recorded. The output format depends on the OS (HP-UX or
Solaris). Output/no output or output destinations of messages, which is output to syslog, can be
specified by modifying descriptions for type (level) and function (facility) in OS settings file
(/etc/syslog.conf).
Note 1: On Solaris system, a message, of which function is “daemon” and classification is “INFO”,
is not output as the default value. Also, a message, of which function is “user” and
classification is “WARNING”, “NOTICE”, or “INFO” is not output as the default value.
To output these kinds of messages, modify the OS settings file.
Note 2: The function of messages output from the iSM to syslog is “Daemon”. However, the
function of the messages output by the ReplicationControl command is “user”.
Messages are output being affixed the following directory/file name as the default value:
HP-UX system:
/var/adm/syslog/syslog.log
Solaris system:
/var/adm/messages
y Event log
This is output on Windows system. Together with the messages output by windows, the messages
output from the iSM and the ReplicationControl are recorded. The messages are output to
application log in the event log. The event log has the functions similar to those of UNIX syslog,
however, the content of the log are different. The event log can be viewed using the [Event Viewer]
in the Management Tool. A message classification and an event log type correspond as follows.
ERROR: Error
WARNING: Warning
NOTICE/ INFO: Information
y ESMPRO Manager
Messages are output to ESMPRO Manager in the Windows environment. If ESMPRO Agent has
been installed in the management server on which the Storage Manager has started, messages to be
notified to the ESMPRO manager of all the messages that the Storage Manager server outputs to an
event log are automatically set to display on the ESMPRO Manager alert viewer. To change the
setting, ESMPRO Agent notification setting must be changed. The notification function provided by
ESMPRO is also available.
Chapter 1 Messages and Output Destinations
6
1
1
1.
.
.3
3
3
M
M
Me
e
es
s
ss
s
sa
a
ag
g
ge
e
e
O
O
Ou
u
ut
t
tp
p
pu
u
ut
t
t
F
F
Fo
o
or
r
rm
m
ma
a
at
t
t
This section describes the message output format and the errno output rule. For details on the message
text, refer to Chapter 2 “Message List”.
The following shows the output format of a message:
Mon Date hh:mm:ss hhhhhh ffffffff :mmmmmm cccccccc : iSMyyyyy : Message body
Mon Date : Month and date
hh:mm:ss : Time
hhhhhh : Host name
ffffffff : Function identifier
mmmmmm : Message classification
cccccccc : Command name and function name
yyyyy : Message number
The message, which is output to application log in the event log, includes the following values specified
for each item:
y Classification
ERROR : Error
WARNING : Warning
NOTICE : Information
INFO : Information
y Source
Storage Manager : (fixed)
y Classification
None (fixed)
y Event ID
Number part in the message ID output to the operation log.
The following describes output rules for errno:
y Windows system
1. Routine in C Runtime library: errno value is defined by the library.
2. WIN32 API: The value returned by GetLastError with 20000 added is output.
3. Socket API: The value returned by WSGetLastError with 20000 added is output.
Chapter 1 Messages and Output Destinations
7
y UNIX system
1. A defined value is output as is.
Chapter 2 Message List
8
Chapter 2 Message List
2
2
2.
.
.1
1
1
I
I
In
n
nt
t
te
e
er
r
rp
p
pr
r
re
e
et
t
ta
a
at
t
ti
i
io
o
on
n
n
o
o
of
f
f
M
M
Me
e
es
s
ss
s
sa
a
ag
g
ge
e
e
L
L
Li
i
is
s
st
t
t
2.2 “Message List” describes the messages in the order of message IDs. The message are described in
the following format:
iSMxxxxx: AAAAA<aaa>,<bbb...b>
Message ID (iSMxxxxx) and message body (AAAAA<aaa>,<bbb...b>) are described.
Descriptions using parentheses such as <aaa> and <bbb...b> indicate that parameter values are not fixed.
(The parentheses “<” and “>” are not displayed in the actual message.)
For details of parameter values, refer to [Explanation].
Messages subject to ALIVE report (including ALIVE report from a disk array) are followed by the
keyword [_ALERT_] and output to each destination. For messages subject to ALIVE report
excluding ALIVE report from a disk array, refer to Appendix A “Message Output Destination List”.
[Classification] Message classification (ERROR, WARNING, NOTICE, or INFO) is described.
A message that is not output to syslog, event log, or operation log is output
without a message classification. This field is blank for such a message that is
output without a message classification.
[Explanation] This field describes the causes of the message output, etc. Parameters in the
message are also described in this field.
If a message is output on a specific OS (UNIX or Windows), applicable OS names
are described in this field. Unless otherwise noted, the message is a common
message that is independent of OS.
[Measure] This field describes measures to be taken by an administrator. An administrator
must follow the instructions to take measures.
Note: For output destination of a message, refer to Appendix A “Message Output Destination List”.
Chapter 2 Message List
9
2
2
2.
.
.2
2
2
M
M
Me
e
es
s
ss
s
sa
a
ag
g
ge
e
e
L
L
Li
i
is
s
st
t
t
iSM01000 ∼
iSM01001: Storage Manager has started
[Classification] INFO
[Explanation] It shows that iSM server has started.
For Windows, this message is target of ESMPRO Manager Report.
[Measures] Unnecessary
iSM01002: Storage Manager is ready
[Classification] INFO
[Explanation] It shows that iSM server has become capable of operation.
For Windows, this message is target of ESMPRO Manager Report.
[Measures] Unnecessary
iSM01003: Storage Manager has terminated
normally
[Classification] INFO
[Explanation] It shows that iSM server has normally terminated.
For Windows, this message is target of ESMPRO Manager Report.
[Measures] Unnecessary
Chapter 2 Message List
10
iSM01004: Storage Manager has terminated
emergency
[Classification] WARNING
[Explanation] Emergency shutdown of iSM server.
This message is output in the iSM server abort processing when iSMsvr stop -e is
executed or the system is shut down.
This message is output on UNIX system.
[Measures] Unnecessary
iSM01005: Command is entered.command=
<aaa…a>
[Classification] INFO
[Explanation] It shows that a command is entered.
This message is output on UNIX system.
aaa...a: command that is entered
[Measures] Unnecessary
iSM01006: Termination of Storage Manager is
started
[Classification] WARNING
[Explanation] It shows that abort processing of iSM server is started.
[Measures] Unnecessary
Chapter 2 Message List
11
iSM01010: Storage Manager has restarted
[Classification] INFO
[Explanation] It shows that the iSM server is restarted.
For Windows, this message is target of ESMPRO Manager Report.
[Measures] Unnecessary
iSM01011: <aaa...a> has restarted
[Classification] INFO
[Explanation] It shows that a process indicated with aaa...a is restarted.
For Windows, this message is target of ESMPRO Manager Report.
aaa...a : Process name
[Measures] Unnecessary
Chapter 2 Message List
12
iSM01101: The function is not available.
function=<aaa...a>
[Classification] WARNING
[Explanation] The function indicated with aaa...a has become unavailable. iSM server will
block the function.
aaa...a : Unavailable function
PerformanceMonitor : Performance monitoring function
ReplicationControl : Replication control function
msgdrv : Event link function
config GUI : Configuration setting GUI function
ALIVEmail : ALIVEmail function
PerformanceOptimizer : Performance optimization function
iSMcmd : Configuration setting GUI function
FileTransfer : File transfer function
SnapShot : Snapshot function
[Measures] Examine the cause by studying iSM server’s syslog or iSM operation log.
To use a function indicated with aaa...a, the iSM server must be restarted.
iSM01102: Command failed
[Classification] NOTICE
[Explanation] It shows that iSMsvr stop/update/prf_start/prf_stop/prf_update command
execution is failed. The entered command is ignored.
A message indicating the error cause is displayed before this message is output.
This error may occur when the linkage function or performance monitoring
function is terminated.
This message is output on UNIX system.
[Measures] Investigate and remove the cause of error by referencing the message that is
displayed before this message. Restart the iSM server if necessary.
Chapter 2 Message List
13
iSM01103: Socket access failed. process=
<aaa...a> func=<bbb...b>
[errno=<ccc>|error=<ddd...d>]
detail=<ee-fff>
[Classification] NOTICE
[Explanation] Error has occurred in the socket communication between the processes indicated
with aaa...a and the main process. This error occurs when the process has stopped
or the file environment of iSM Server’s socket path (/opt/iSMsvr/etc/sock) is in
an incorrect status.
aaa...a : Process name
bbb...b : Socket system function name
ccc : Error number
ddd...d : Error contents
timeout : Time out
socket close : Socket is closed
ee-fff : Detail code (This code is not disorder reason but a value for
maintenance.)
[Measures] If an error number is output, check the function name and the error number to
take measures, and restart the iSM server if necessary. When an error contents
is output, examine the cause through the previous message output before this
message and restart the iSM server if necessary.
Chapter 2 Message List
14
iSM01105: File access failed. file=<aaa...a>
func=<bbb...b> errno=<ccc>
detail=<dd-eee>
[Classification] NOTICE
[Explanation] It shows that an error has occurred in accessing the file indicated with aaa...a.
In this message case, the environment of environment definition file
(/etc/iSMsvr/iSMsvr.conf) or control file (files under /opt/iSMsvr/etc.) may be in
an incorrect status.
aaa...a : File path name
bbb...b : File system function name
ccc : Error number
dd-eee : Detail code (This code is not disorder reason but a value for
maintenance.)
[Measures] Resolve the problem by checking the file path name, function name and error
number, and restart the iSM server.
iSM01106: System call error occurred.
process=<aaa...a> func=<bbb...b>
errno=<ccc> detail=<dd-eee>
[Classification] NOTICE
[Explanation] It shows that an error has occurred in the system function except the access of
socket/file.
The following hindrance is likely as an example.
y In case of syslog:
The shared memory has been deleted incorrectly with the ipcrm command.
(Access error of shared memory)
y In case of operation log:
System overloading occurred by requests of iSM server. Some resources
have been lost.
aaa...a : Process name
bbb...b : System function name
ccc : Error number
dd-eee : Detail code (This code is not disorder reason but a value for
maintenance.)
[Measures] Check the function name and error number to take measures, and restart the iSM
server if necessary.
Chapter 2 Message List
15
iSM01107: <aaa...a> process has terminated
abnormally
[Classification] WARNING
[Explanation] It shows that the process indicated with aaa...a has been abnormally terminated.
A message of the cause has been reported from the abnormally terminated
process right before this message.
For Windows, this message is target of ESMPRO Manager Report.
aaa...a : Process name
[Measures] Resolve the problem through the previous message output before this message,
and restart the iSM server if necessary.
iSM01108: Storage Manager has already started
[Classification] NOTICE
[Explanation] It shows that the iSM server has already started.
This message is output on UNIX system.
[Measures] Unnecessary
iSM01109: Internal error occurred.
detail=<aa-bbb>
[Classification] WARNING
[Explanation] It shows that an internal error has occurred in the main process of iSM server.
iSM server will be terminated.
aa-bbb : Detail code (This code is not disorder reason but a value for
maintenance.)
[Measures] Acquire the information and restart the iSM server if necessary. For the
acquiring method of the information, refer to 6.1.9 “Information Gathering
Method when Server Fault with Unknown Cause” of the “User’s Manual”.
Chapter 2 Message List
16
iSM01110: Illegal configuration. file=<aaa...a>
line=<bbb...b> [section=<ccc...c>]
[keyword=<ddd...d>]
[value=<eee...e>] [token=<fff...f>]
[detail=<ggg...g>]
[Classification] NOTICE
[Explanation] It shows that an illegal configuration is detected in the environment definition
file. iSM Server will be abnormally terminated.
aaa...a : Environment definition file name
bbb...b : Line number with illegal configuration
ccc...c : Section name or words wherein illegal configuration was found
ddd...d : Parameter name or words wherein illegal configuration was
found
eee...e : Parameter value or words wherein illegal configuration was
found
fff...f : Words wherein illegal configuration was found
ggg...g : Detailed information
[Measures] Find out incorrect description in the file through the output message, correct it
and then restart the iSM server.
Probable causes of detail information output are as follows:
Detail Information Content
Duplicate section The same section name has been specified more than
once.
Duplicate keyword The same keyword has been specified more than once.
Too many diskarray The number of disk arrays exceeds the limitation.
Too many diskarray
number
The disk array number exceeds the value n of
diskarray[n].
Too many ip The number of IP addresses exceeds the limitation.
Too many special
file
The number of specified special files exceeds the
limitation.
Too many disk The specified disk number exceeds the limitation.
Too may login The number of user information items exceeds the
limitation.
Too many login
number
The user number exceeds the value n of login[n].
Chapter 2 Message List
17
iSM01111: User definition does not exist, Client
cannot be connected. file=<aaa...a>
[Classification] NOTICE
[Explanation] It shows that there is no specification of the indispensable parameter of the
environment definition file. The indispensable parameter is a login parameter in
the client section.
aaa...a : Environment definition file name
[Measures] Specify the login parameter of the client section in the environment definition
file and restart the iSM server.
iSM01113: iSMadm cannot use UDP port 162.
file=<aaa...a> line=<bbb...b>
[section=<ccc...c>]
[keyword=<ddd...d>]
[value=<eee...e>]
[Classification] NOTICE
[Explanation] It shows that the port 162 specified by iSMadm user cannot be used. iSM
Server will be abnormally terminated.
This message is output on UNIX system.
aaa...a : Environment definition file name
bbb...b : Line number with illegal configuration
ccc...c : Section name or words wherein illegal configuration was found
ddd...d : Parameter name or words wherein illegal configuration was
found
eee...e : Parameter value or words wherein illegal configuration was
found
[Measures] Restart the iSM server with Super User to receive SNMP trap while the iSM
server uses the port 162. If the iSM server does not use the port 162 for
receiving SNMP trap, restart the iSM server after deleting the parameter for
snmp_port.
Chapter 2 Message List
18
iSM01230: Storage Manager has terminated
abnormally
[Classification] WARNING
[Explanation] It shows that iSM server has terminated abnormally. The message of the cause
has displayed before this message.
For Windows, this message is target of ESMPRO Manager Report.
[Measures] Examine the cause through the previous message output before this message and
restart the iSM server if necessary.
iSM01232: Storage Manager has terminated
abnormally by signal.signo=<aaa>
[Classification] ERROR
[Explanation] It shows that iSM server has terminated abnormally due to the signal. The user
may send the kill signal.
This message is output on UNIX system.
aa…a: Signal number
[Measures] Restart the iSM server.
iSM01400: This function is not supported
[Explanation] It indicates that functions other than start, stop, update, or prf_update has been
specified by iSMsvr command.
This message is output on UNIX system.
[Measures] Check command format and retry.
Chapter 2 Message List
19
iSM01401: Usage: iSMsvr start
[Explanation] It indicates that description of iSMsvr start command is incorrect. A specifiable
format is shown in the message. Execute the command in valid format.
This message is output on UNIX system.
[Measures] Check command format and retry.
iSM01402: Usage: iSMsvr stop [-e]
[Explanation] It indicates that description of iSMsvr stop command is incorrect. A specifiable
format is shown in the message. Execute the command in valid format.
This message is output on UNIX system.
[Measures] Check command format and retry.
iSM01403: Usage: iSMsvr update {-m | -s name |
-r name}
[Explanation] It indicates that description of iSMsvr update command is incorrect. A
specifiable format is shown in the message. Execute the command in valid
format.
This message is output on UNIX system.
[Measures] Check command format and retry.
iSM01407: Rejected: Storage Manager is not
ready
[Explanation] It indicates that a command was not accepted because the iSM is not operative.
[Measures] Retry command execution when the iSM becomes operative.
Chapter 2 Message List
20
iSM01408: Rejected: System function error
(<aaa...a>) <bbb...b>
[Explanation] It indicates that an error occurred in a system function indicated by “aaa...”.
aaa...a : System function name
bbb...b : Error description
errno= zzzz : Error number
socket close : Socket with iSM closed
timeout : Time-out occurred in socket communication
with the iSM.
[Measures] Check error description and retry command execution.
If this message is output on a HP-UX system, the following reason is assumed:
iSM01408: Rejected: System function error (execl) errno=13
When the iSM server is operated by the administrator for iSM, the setting of the
administrator for iSM may not be deleted before uninstallation of the iSM server.
In this case, register the administrator for iSM again (delete and set) using the
iSM setting command (iSMmkadm). For details on the administrator for iSM
setting command, refer to the “User's Manual (UNIX)”.
iSM01409: Rejected: msgdrv is not available
[Explanation] It indicates that the event link function is not available.
This message is output on UNIX system.
[Measures] Restarting the iSM is required to use the event link function.
iSM01410: This request is accepted
[Explanation] It indicates that a device monitoring stop/restart command request has been
received. For actual stop/restart operations, refer to syslog.
This message is output on UNIX system.
[Measures] Unnecessary
Chapter 2 Message List
21
iSM01411: Rejected: PerformanceMonitor is not
available
[Explanation] It indicates that the performance monitor function is not available.
[Measures] Unnecessary
iSM01412: Internal error. detail=<aaaa>
[Explanation] It indicates that an internal error has occurred.
aaaa : Internal code
[Measures] Obtain information and restart the iSM.
iSM01413: Usage: iSMsvr prf_update -t value
[Explanation] It indicates that description of iSMsvr prf_update command is incorrect. A
specifiable format is shown in the message. Execute the command in valid
format.
This message is output on UNIX system.
[Measures] Check command format and retry.
iSM01901: Function error has occurred.
Function name=<aaa...a> Error
code=<bbb> Error Message=<ccc...c>
[Classification] ERROR
[Explanation] It is an internal error of iSMmainNT. This seems to be a problem depending on
Windows system.
This message is output on Windows system.
aaa...a : Function name
bbb : Error number
ccc...c : Error message
[Measures] Resolve the problem by checking the function name and the error number, and
restart the iSM server.
Chapter 2 Message List
22
iSM02000 ∼
iSM02010: In initialization, port setting failed
errno=<aaaaa>
[Classification] NOTICE
[Explanation] It shows that port number setting has failed in the initializing process.
aaaaa : Error number
[Measures] Take the measures below.
For UNIX : Check the port number setting in the [client] section of the
environment definition file in order to see if the iSM port number
which is specified in the iSMsvr_port parameter or the port
number of 8020 at the time of an abbreviation is being used in
other service, or if the specified port number is correct. To
check the port number being used, use netstat command.
For Windows: Check the server operation environment and review the port
number settings.
iSM02011: In initialization, shared memory
allocation failed errno=<aaaaa>
[Classification] NOTICE
[Explanation] It shows that the acquisition of shared memory has failed in the initializing
process.
aaaaa : Error number
[Measures] Take the measures below.
For UNIX : Check the shared memory status by using ipcs command since
there is a shortage of usable memory in the system.
For Windows: Check the server operating status including memory usage status.
Chapter 2 Message List
23
iSM02020: Function Error has occurred
name=<aaa...a> code=<bbbbb>
errno=<ccccc>
[Classification] NOTICE
[Explanation] It shows that a function error has occurred.
This message is output on UNIX system.
aaa...a : Function name
bbbbb : Internal code
ccccc : Error number
[Measures] Check the settings relevant to the applicable function.
Example: iSMclcomm iSM02020:Function Error has occurred name=recv
code=417 errno=232
In this case, recv function has error-returned in the
errno=232(ECONNRESET:Connection reset by peer) and it is
thought that the socket has been disconnected from a client.
iSM02021: Internal Error has occurred
code=<aaaaa> errno=<bbbbb>
[Classification] NOTICE
[Explanation] It shows that an internal error has occurred.
This message is output on UNIX system.
aaaaa : Internal code
bbbbb : Error number
[Measures] Check the connection status of iSM client, the environment of server operation
and various settings. This message is usually output together with iSM02020.
For the specific cause, refer to iSM02020.
Example: iSMclcomm iSM02020:Function Error has occurred name=recv
code=417 errno=232
iSMclmaind iSM02021:Internal Error has occurred code=1366
errno=*
This case shows that the socket has been disconnected from a client in
iSM02020 and the communication process for the client has ended.
Chapter 2 Message List
24
iSM02040: iSM/Client connected user=<aaa...a>
client=<bbbbbbbb> ip=<ccc...c>
[Classification] INFO
[Explanation] It shows that an iSM client is connected.
aaa...a : User name
bbbbbbbb : iSM client name
ccc...c : iSM client’s IP address
[Measures] Unnecessary (This message indicates that the operation is completed as
required.)
iSM02041: iSM/Client terminated user=<aaa...a>
client=<bbbbbbbb> ip=<ccc...c>
[Classification] INFO
[Explanation] It shows that an iSM client has exited.
aaa...a : User name
bbbbbbbb : iSM client name
ccc...c : iSM client’s IP address
[Measures] Unnecessary (This message indicates that the operation is completed as
required.)
Chapter 2 Message List
25
iSM02042: iSM/Client disconnected
user=<aaa...a> client=<bbbbbbbb>
ip=<ccc...c> reason=<ddd>
[Classification] NOTICE
[Explanation] It shows that the iSM client has been disconnected.
aaa...a : User name
bbbbbbbb : iSM client name
ccc...c : iSM client’s IP address
ddd : Reason of the disconnection
001 : Hindrance generated in the client
002 : Time out generated in the client
003 : Others
[Measures] Connect the client again if necessary.
iSM02043: iSM/Client connect failed
user=<aaa...a> client=<bbbbbbbb>
ip=<ccc...c> reason=<ddd>
[Classification] NOTICE
[Explanation] It shows that iSM client has failed to connect.
aaa...a : User name
bbbbbbbb : iSM client name
ccc...c : iSM client’s IP address
ddd : Reason of the disconnection
001 : Incorrect user’s name
002 : Incorrect password
003 : Incorrect IP address
004 : Excessive connection of clients
005 : Resource shortage
006 : Reconnection demand during the process of
disconnection of the client
007 : Start terminating iSM server
008 : Internal error generated
009 : Others
010 : Time out generated in the iSM server
[Measures] Resolve the problem from the reason of disconnection and reconnect the client.
Chapter 2 Message List
26
iSM02050: iSM/Client Management Service
started
[Classification] INFO
[Explanation] It shows that iSM/Client Management Service has started.
[Measures] Unnecessary (This message indicates that the operation is completed as
required.)
iSM02051: iSM/Client Management Service
terminated
[Classification] INFO
[Explanation] It shows that iSM/Client Management Service has terminated.
[Measures] Unnecessary (This message indicates that the operation is completed as
required.)
iSM02052: iSM/Client Management Service
termination started
[Classification] INFO
[Explanation] It shows that termination of iSM/Client Management Service has started.
[Measures] Unnecessary (This message indicates that the operation is completed as
required.)
Chapter 2 Message List
27
iSM02053: iSM/Client Management Service is
waiting for L3 user’s termination
[Classification] INFO
[Explanation] It shows that iSM/Client Management Service is waiting for the termination of
L3 user.
This message is output on UNIX system.
[Measures] iSM server has become the state of waiting for the disconnection of L3 user who
is in the controlling level. To terminate the iSM server, the disconnection from
the L3 user client is necessary.
iSM02060: Data lost detected client=<aaaaaaaa>
ip=<bbb...b>
[Classification] NOTICE
[Explanation] It shows that lost of received and transmitted data during process occurred.
This message is output on UNIX system. (Output only to syslog)
aaaaaaaa : iSM client name
bbb...b : iSM client’s IP address
[Measures] Remove the status that hinders data transmission in the client’s operation
environment or server’s operation environment etc. In this case, the response to
operation demand from iSM client may possibly be lost and the information
display in the iSM client may not be shown completely.
Chapter 2 Message List
28
iSM02061: Data lost recovered
client=<aaaaaaaa> ip=<bbb...b>
[Classification] NOTICE
[Explanation] It shows that the received and transmitted data lost during process has been
recovered.
This message is output on UNIX system. (Output only to syslog)
aaaaaaaa : iSM client name
bbb...b : iSM client’s IP address
[Measures] Check if the data loss has an influence on operation or not. Check if a message
indicating a trouble on operation has been output or not between the iSM02060
message and this message.
Chapter 2 Message List
29
iSM03000 ∼
iSM03100: Disk Array is not specified in the
config file. detail=<aa-bbbb>
[Classification] WARNING
[Explanation] It indicates that no monitoring disk array exists for the iSM server because disk
array has not been specified.
aa-bbbb : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check description of agent section (disk array or auto_find_spf) in the
environment definition file. If no problem is found, check disk connection
environment and restart the iSM server.
On Windows system, check environment settings (disk array information). If
no problem is found, check disk connection environment and restart the iSM
server.
iSM03101: Object Disk Array does not exist.
detail=<aa-bbbb>
[Classification] WARNING
[Explanation] It shows that the iSM server is started with no disk arrays to be controlled,
because no disk arrays to be controlled are found.
aa-bbbb : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check description of agent section (diskarray or auto_find_spf) in the
environment definition file. If no problem is found, check disk connection
environment and restart the iSM server.
On Windows system, check environment settings (disk array information). If
no problem is found, check disk connection environment and restart the iSM
server.
Chapter 2 Message List
30
iSM03102: Diskarray[<a>] and diskarray[<b>] are
the same disk. detail=<cc-dddd>
[Classification] ERROR
[Explanation] It indicates that disk arrays specified by diskarray [a] and diskarray [b] overlap
with each other. The iSM server terminates abnormally.
a : Disk array specifying number in environment definition file
(UNIX system: 1 to 64, Windows system: 1 to 32)
b : Disk array specifying number in environment definition file
(UNIX system: 1 to 64, Windows system: 1 to 32)
cc-dddd : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Describe agent section (diskarray [a] and diskarray [b]) in environment definition
file correctly, and restart the iSM server.
On Windows system, correctly specify diskarray [a] and diskarray [b] in
environment settings (specifying disk array information) and restart the iSM
server.
iSM03103: IP address (<aaa...a>) in
diskarray[<b>] is invalid description.
detail=<cc-dddd>
[Classification] ERROR
[Explanation] IP address specified by diskarray [b] is incorrect. The iSM server terminates
abnormally.
aaa...a : IP address
b : Disk array specifying number in environment definition file
(UNIX system: 1 to 64, Windows system: 1 to 32)
cc-dddd : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Describe agent section (diskarray [b]) in environment definition file correctly,
and restart the iSM server.
On Windows system, correctly specify diskarray [b] in environment settings
(specifying disk array information) and restart the iSM server.
Chapter 2 Message List
31
iSM03104: IP address (<aaa...a>) in
diskarray[<b>] is not control path to
the management object.
detail=<cc-dddd>
[Classification] ERROR
[Explanation] It indicates that IP address specified by diskarray [b] is not a control path of the
monitoring target disk array. The iSM server terminates abnormally.
aaa...a : IP address
b : Disk array specifying number in environment definition file
(UNIX system: 1 to 64, Windows system: 1 to 32)
cc-dddd : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Describe agent section (diskarray [b]) in environment definition file correctly,
and restart the iSM server.
On Windows system, correctly specify diskarray [b] in environment settings
(specifying disk array information) and restart the iSM server.
iSM03105: IP address (<aaa...a>) in
diskarray[<b>] is defined in the other
specification. detail=<cc-dddd>
[Classification] ERROR
[Explanation] IP address specified by diskarray [b] is overlapping with others. The iSM
server terminates abnormally.
aaa...a : IP address
b : Disk array specifying number in environment definition file
(UNIX system: 1 to 64, Windows system: 1 to 32)
cc-dddd : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Describe agent section (diskarray [b]) in environment definition file correctly,
and restart the iSM server.
On Windows system, correctly specify diskarray [b] in environment settings
(specifying disk array information) and restart the iSM server.
Chapter 2 Message List
32
iSM03106: IP address (<aaa...a>) in
diskarray[<b>] is same as one in
diskarray[<c>]. detail=<dd-eeee>
[Classification] ERROR
[Explanation] The same IP address is specified in diskarray [b] and diskarray [c]. The iSM
server terminates abnormally.
aaa...a : IP address
b : Disk array specifying number in environment definition file
(UNIX system: 1 to 64, Windows system: 1 to 32)
c : Disk array specifying number in environment definition file
(UNIX system: 1 to 64, Windows system: 1 to 32)
dd-eeee : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Describe agent section (diskarray [b] and diskarray [c]) in environment definition
file correctly, and restart the iSM server.
On Windows system, correctly specify diskarray [b] and diskarray [c] in
environment settings (specifying disk array information) and restart the iSM
server.
iSM03107: IP address (<aaa...a>) in
diskarray[<b>] contradicts the other
specification. detail=<cc-dddd>
[Classification] ERROR
[Explanation] The IP addresses specified in diskarray [b] indicates different disk arrays. iSM
server terminates abnormally.
aaa...a : IP address
b : Disk array specifying number in environment definition file
(UNIX system: 1 to 64, Windows system: 1 to 32)
cc-dddd : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Describe agent section (diskarray [b]) in environment definition file correctly,
and restart the iSM server.
On Windows system, correctly specify diskarray [b] in environment settings
(specifying disk array information) and restart the iSM server.
Chapter 2 Message List
33
iSM03108: File (<aaa...a>) in diskarray[<b>] is
invalid description. detail=<cc-dddd>
[Classification] ERROR
[Explanation] A special file specified by diskarray [b] is incorrect. The file may not exist or
the file may not be a character-type special file. The iSM server terminates
abnormally.
This message is output on UNIX system.
aaa...a : Special file name
b : Disk array specification number (1 to 64) in the environment
definition file (agent section)
cc-dddd : Detail information
[Measures] Correctly specify diskarray [b] in environment settings (specifying disk array
information) and restart the iSM server.
iSM03108: Disk (disk<aaa> (Port<bbb>
Bus<ccc> Target<ddd> Lun<eee>)) in
diskarray[<f>] is invalid description.
detail=<gg-hhhh>
[Classification] ERROR
[Explanation] The disk specified for diskarray[f] in the environment definition file (agent
section) is erroneous. The disk may be nonexistent. The iSM server
terminates abnormally
This message is output on Windows system.
diskaaa (Portbbb Busccc Targetddd Luneee): Disk information
f : Disk array specification number (1 to 32) in the environment
definition file (agent section)
gg-hhhh : Detail information
[Measures] Correctly specify diskarray [f] in environment settings (specifying disk array
information) and restart the iSM server.
Chapter 2 Message List
34
iSM03109: File (<aaa...a>) in diskarray[<b>] is
not control path to the management
object. detail=<cc-dddd>
[Classification] ERROR
[Explanation] A special file specified by diskarray [b] is not a control path for the monitoring
target disk array. The iSM server terminates abnormally.
This message is output on UNIX system.
aaa...a : Special file name
b : Disk array specification number (1 to 64) in the environment
definition file (agent section)
cc-dddd : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Correctly specify diskarray [b] in environment settings (specifying disk array
information) and restart the iSM server.
iSM03109: Disk (disk<aaa> (Port<bbb>
Bus<ccc> Target<ddd> Lun<eee>)) in
diskarray[<f>] is not control path to
the management object.
detail=<gg-hhhh>
[Classification] ERROR
[Explanation] A disk specified by environment setting (setting of disk array) is not a control
path for the monitoring target disk array. The iSM server terminates
abnormally.
This message is output on Windows system.
diskaaa (Portbbb Busccc Targetddd Luneee): Disk information
f : Disk array specification number (1 to 32) in the environment
definition file (setting of disk array information)
gg-hhhh : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Correctly specify diskarray [f] in environment settings (specifying disk array
information) and restart the iSM server.
Chapter 2 Message List
35
iSM03110: File (<aaa...a>) in diskarray[<b>] is
defined in the other specification.
detail=<cc-dddd>
[Classification] ERROR
[Explanation] It indicates that disk arrays specified by diskarray [b] overlap with each other.
The iSM server terminates abnormally.
This message is output on UNIX system.
aaa...a : Special file name
b : Disk array specification number (1 to 64) in the environment
definition file (agent section)
cc-dddd : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Correctly specify diskarray [b] in environment settings (specifying disk array
information) and restart the iSM server.
iSM03110: Disk (disk<aaa> (Port<bbb>
Bus<ccc> Target<ddd> Lun<eee>)) in
diskarray[<f>] is defined in the other
specification. detail=<gg-hhhh>
[Classification] ERROR
[Explanation] Disks specified in environment setting (setting of disk arrays) overlap with each
other. The iSM server terminates abnormally.
This message is output on Windows system.
diskaaa (Portbbb Busccc Targetddd Luneee): Disk information
f : Disk array specification number (1-32) of environment setting
(setting of disk array information)
gg-hhhh : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Correctly specify diskarray [f] in environment settings (specifying disk array
information) and restart the iSM server.
Chapter 2 Message List
36
iSM03111: File (<aaa...a>) in diskarray[<b>] is
same as one in diskarray[<c>].
detail=<dd-eeee>
[Classification] ERROR
[Explanation] The same special file is specified in diskarray [b] and diskarray [c]. The iSM
server terminates abnormally.
This message is output on UNIX system.
aaa...a : Special file name
b : Disk array specification number (1 to 64) in the environment
definition file (agent section)
c : Disk array specification number (1 to 64) in the environment
definition file (agent section)
dd-eeee : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Correctly specify diskarray [b] and diskarray [c] in environment settings
(specifying disk array information) and restart the iSM server.
iSM03111: Disk (disk<aaa> (Port<bbb>
Bus<ccc> Target<ddd> Lun<eee>)) in
diskarray[<f>] is same as one in
diskarray[<g>]. detail=<hh-iiii>
[Classification] ERROR
[Explanation] The same disk is specified in diskarray [f] and diskarray [g]. The iSM server
terminates abnormally.
This message is output on Windows system.
diskaaa (Portbbb Busccc Targetddd Luneee): Disk information
f : Disk array specification number (1 to 32) of environment setting
(setting of disk array information)
g : Disk array specification number (1 to 32) in the environment
definition file (agent section)
hh-iiii : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Correctly specify diskarray [f] and diskarray [g] in environment settings
(specifying disk array information) and restart the iSM server.
Chapter 2 Message List
37
iSM03112: File (<aaa...a>) in diskarray[<b>]
contradicts the other specification.
detail=<cc-dddd>
[Classification] ERROR
[Explanation] The special files specified in diskarray [b] indicates different disk arrays. The
iSM server terminates abnormally.
This message is output on UNIX system.
aaa...a : Special file name
b : Disk array specification number (1 to 64) in the environment
definition file (agent section)
cc-dddd : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Correctly specify diskarray [b] in environment settings (specifying disk array
information) and restart the iSM server.
iSM03112: Disk (disk<aaa> (Port<bbb>
Bus<ccc> Target<ddd> Lun<eee>)) in
diskarray[<f>] contradicts the other
specification. detail=<gg-hhhh>
[Classification] ERROR
[Explanation] The disks specified in disk array in environment definition indicate different disk
arrays. The iSM server terminates abnormally.
This message is output on Windows system.
diskaaa (Portbbb Busccc Targetddd Luneee): Disk information
f : Disk array specification number (1-32) of environment setting
(setting of disk array information)
gg-hhhh : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Correctly specify diskarray [f] in environment settings (specifying disk array
information) and restart the iSM server.
Chapter 2 Message List
38
iSM03113: All control paths of diskarray[<a>]
are not available. detail=<bb-cccc>
[Classification] WARNING
[Explanation] All control paths of diskarray [a] have been blocked. Monitoring to the disk
array is disabled.
a : Disk array specifying number in environment definition file
(UNIX system: 1 to 64, Windows system: 1 to 32)
bb-cccc : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check connection to the disk, and restart the iSM server.
iSM03114: Diskarray[<a>] is already managed by
autofind. detail=<bb-cccc>
[Classification] WARNING
[Explanation] The diskarray [a] has already been incorporated by automatic detecting function.
This message is displayed when incorporating by an IP address specified by
diskarray [a] failed upon iSM server startup, and the disk array has been
incorporated by the automatic detection function. Access to the disk array is
not made via the IP address (Ethernet) specified for diskarray[a] but via FC
a : Disk array specifying number in environment definition file
(UNIX system: 1 to 64, Windows system: 1 to 32)
bb-cccc : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check IP connection to the disk array, and restart the iSM server and select IP
connection if necessary.
Chapter 2 Message List
39
iSM03120: Management of diskarray[<a>]
succeeded. name=(<bbb...b>)
detail=<cc-dddd>
[Classification] INFO
[Explanation] Succeeded in incorporating disk array specified by agent section (diskarray [a])
in environment definition file.
On Windows system, the message indicates that the disk array specified by
environment setting (setting of disk array information) diskarray [a] was
successfully incorporated.
a : Disk array specifying number in environment definition file
(UNIX system: 1 to 64, Windows system: 1 to 32)
bbb...b : Disk array name
cc-dddd : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Unnecessary
iSM03121: Management of diskarray[<a>] failed.
detail=<bb-cccc>
[Classification] WARNING
[Explanation] Failed in incorporating disk array specified by agent section (diskarray [a]) in
environment definition file.
On Windows system, the message indicates that the disk array specified by
environment setting (setting of disk array information) diskarray [a] was failed in
incorporating.
The reason for failure of management is indicated in the preceding message.
After that, the disk array may be automatically managed during operation of
iSM.
a : Disk array specifying number in environment definition file
(UNIX system: 1 to 64, Windows system: 1 to 32)
bb-cccc : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the message preceding this message, and take measures.
Chapter 2 Message List
40
iSM03122: Management of diskarray succeeded
by autofind. name=(<aaa...a>)
detail=<bb-cccc>
[Classification] INFO
[Explanation] It shows that management of disk array is successful via automatic detection
function.
aaa...a : Disk array name
bb-cccc : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Unnecessary
iSM03130: Management of control path in
diskarray[<a>] failed.ip=<bbb...b>
port=<ccccc> func=<ddd...d>
errno=<eee> detail=<ff-gggg>
[Classification] NOTICE
[Explanation] Failed in building the control path.
a : Disk array specifying number in environment definition file
(UNIX system: 1 to 64, Windows system: 1 to 32)
bbb...b : IP address
ccccc : Port number
ddd...d : Function name
eee : Error number
ff-gggg : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the network connection state to the disk array and the disk array state, and
remove the failure.
Chapter 2 Message List
41
iSM03131: Management of control path in
diskarray[<a>] failed. ip=<bbb...b>
port=<ccccc> func=<ddd...d>
reason=(timeout <eee>sec.)
detail=<ff-gggg>
[Classification] NOTICE
[Explanation] Failed in the inclusion of the control path due to time out.
a : Disk array specifying number in environment definition file
(UNIX system: 1 to 64, Windows system: 1 to 32)
bbb...b : IP address
ccccc : Port number
ddd...d : Function name
eee : Seconds of the time out
ff-gggg : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the network connection state to the disk array, and remove the failure.
iSM03132: Management of control path in
diskarray[<a>] failed. ip=<bbb...b>
port=<ccccc> reason=(invalid
sequence) detail=<dd-eeee>
[Classification] NOTICE
[Explanation] Failed in the inclusion of the control path.
a : Disk array specifying number in environment definition file
(UNIX system: 1 to 64, Windows system: 1 to 32)
bbb...b : IP address
ccccc : Port number
dd-eeee : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Settings of disk array may be incorrect (monitoring by the node running iSM
server via LAN may not be allowed). Check settings of disk array and remove
fault.
Chapter 2 Message List
42
iSM03133: Management of control path in
diskarray[<a>] failed. ip=<bbb...b>
port=<ccccc> reason=(invalid receive
data) detail=<dd-eeee>
[Classification] NOTICE
[Explanation] Failed in the inclusion of the control path.
a : Disk array specifying number in environment definition file
(UNIX system: 1 to 64, Windows system: 1 to 32)
bbb...b : IP address
ccccc : Port number
dd-eeee : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the disk array state, and remove the failure.
iSM03134: Management of control path in
diskarray[<a>] failed. ip=<bbb...b>
port=<ccccc> command=(<ddd...d>)
status=(<ee>/<ff>/<gg>/<hh>)
detail=<ii-jjjj>
[Classification] NOTICE
[Explanation] Failed in the inclusion of the control path.
a : Disk array specifying number in environment definition file
(UNIX system: 1 to 64, Windows system: 1 to 32)
bbb...b : IP address
ccccc : Port number
ddd...d : Command Descriptor Block of the issued command
ee : Status Byte
ff : Sense Key
gg : Additional Sense Code
hh : Additional Sense Code Qualifier
ii-jjjj : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the disk array state, and remove the failure.
Chapter 2 Message List
43
iSM03140: Management of control path in
diskarray[<a>] failed. file=<bbb...b>
func=<ccc...c> errno=<ddd>
detail=<ee-ffff>
[Classification] NOTICE
[Explanation] Failed in the inclusion of the control path.
This message is output on UNIX system.
a : Disk array specification number (1 to 64) in the environment
definition file (agent section)
bbb...b : Special file name
ccc...c : Function number
ddd : Error number
ee-ffff : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the FC connection state to the disk array and the disk array state, and
remove the failure.
iSM03140: Management of control path in
diskarray[<a>] failed.
Disk=(disk<bbb> (Port<ccc>
Bus<ddd> Target<eee> Lun<fff>))
func=<ggg...g> errno=<hhh>
detail=<ii-jjjj>
[Classification] NOTICE
[Explanation] Failed in the inclusion of the control path.
This message is output on Windows system.
a : Disk array specification number (1 to 32) in the environment
definition file (agent section)
diskbbb (Portccc Busddd Targeteee Lunfff): Disk information
ggg...g : Function number
hhh : Error number
ii-jjjj : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the FC connection state to the disk array and the disk array state, and
remove the failure.
Chapter 2 Message List
44
iSM03141: Management of control path in
diskarray[<a>] failed. file=<bbb...b>
command=(<ccc...c>) status=
(<dd>/<ee>/<ff>/<gg>) detail=<hh-iiii>
[Classification] NOTICE
[Explanation] Failed in the inclusion of the control path.
This message is output on UNIX system.
a : Disk array specification number (1 to 64) in the environment
definition file (agent section)
bbb...b : Special file name
ccc...c : Command Descriptor Block of the issued command
dd : Status Byte
ee : Sense Key
ff : Additional Sense Code
gg : Additional Sense Code Qualifier
hh-iiii : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the disk array state, and remove the failure.
iSM03141: Management of control path in
diskarray[<a>] failed.
Disk=(disk<bbb> (Port<ccc>
Bus<ddd> Target<eee> Lun<fff>))
command=(<ggg...g>)
status=(<hh>/<ii>/<jj>/<kk>)
detail=<ll-mmmm>
[Classification] NOTICE
[Explanation] Failed in the inclusion of the control path.
This message is output on Windows system.
a : Disk array specification number (1 to 32) in the environment
definition file (agent section)
diskbbb (Portccc Busddd Targeteee Lunfff): Disk information
ggg...g : Command Descriptor Block of the issued command
hh : Status Byte
ii : Sense Key
jj : Additional Sense Code
kk : Additional Sense Code Qualifier
ll-mmmm : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the disk array state, and remove the failure.
Chapter 2 Message List
45
iSM03142: Management of control path in
diskarray[<a>] failed.file=<bbb...b>
command=(<ccc...c>)
status=(<dddddddd>) detail=<ee-ffff>
[Classification] NOTICE
[Explanation] Failed in the inclusion of the control path.
This message is output on UNIX system.
a : Disk array specification number (1 to 64) in the environment
definition file (agent section)
bbb...b : Special file name
ccc...c : Command Descriptor Block of the issued command
dddddddd : Status Byte
ee-ffff : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the disk array state, and remove the failure.
iSM03142: Management of control path in
diskarray[<a>] failed.
Disk=(disk<bbb> (Port<ccc>
Bus<ddd> Target<eee> Lun<fff>))
command=(<ggg...g>)
status=(<hhhhhhhh>) detail=<ii-jjjj>
[Classification] NOTICE
[Explanation] Failed in the inclusion of the control path.
This message is output on Windows system.
a : Disk array specification number (1 to 32) in the environment
definition file (agent section)
diskbbb (Portccc Busddd Targeteee Lunfff): Disk information
ggg...g : Command Descriptor Block of the issued command
hhhhhhhh : Status Byte
ii-jjjj : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the disk array state, and remove the failure.
Chapter 2 Message List
46
iSM03150: Management of control path by
autofind failed. file=<aaa...a>
func=<bbb...b> errno=<ccc>
detail=<dd-eeee>
[Classification] INFO
[Explanation] Failed in the inclusion of the control path by auto find function.
The disk with error cannot be included to iSM server. iSM server will ignore
error.
This message is output on UNIX system.
aaa...a : Special file name
bbb...b : Function number
ccc : Error number
dd-eeee : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the FC connection state to the disk array and the disk array state, and
remove the failure. Restart iSM server if necessary.
iSM03150: Management of control path by
autofind failed. Disk=(disk<aaa>
(Port<bbb> Bus<ccc> Target<ddd>
Lun<eee>)) func=<fff...f>
errno=<ggg> detail=<hh-iiii>
[Classification] INFO
[Explanation] Failed in the inclusion of the control path by auto find function.
The disk with error cannot be included to iSM server. iSM server will ignore
error.
This message is output on Windows system.
diskaaa (Portbbb Busccc Targetddd Luneee): Disk information
fff...f : Function number
ggg : Error number
hh-iiii : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the FC connection state to the disk array and the disk array state, and
remove the failure. Restart iSM server if necessary.
Chapter 2 Message List
47
iSM03151: Management of control path by
autofind failed. file=<aaa...a>
command=(<bbb...b>)
status=(<cc>/<dd>/<ee>/<ff>)
detail=<gg-hhhh>
[Classification] INFO
[Explanation] Failed in the inclusion of the control path by auto find function.
The disk with error cannot be included in iSM server. iSM server will ignore
the error.
This message is output on UNIX system.
aaa...a : Special file name
bbb...b : Command Descriptor Block of the issued command
cc : Status Byte
dd : Sense Key
ee : Additional Sense Code
ff : Additional Sense Code Qualifier
gg-hhhh : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the disk array state, and remove the failure. Restart iSM server if
necessary.
iSM03151: Management of control path by
autofind failed. Disk=(disk<aaa>
(Port<bbb> Bus<ccc> Target<ddd>
Lun<eee>)) command=(<fff...f>)
status=(<gg>/<hh>/<ii>/<jj>)
detail=<kk-llll>
[Classification] INFO
[Explanation] Failed in the inclusion of the control path by auto find function.
The disk with error cannot be included in iSM server. iSM server will ignore
the error.
This message is output on Windows system.
diskaaa (Portbbb Busccc Targetddd Luneee): Disk information
fff...f : Command Descriptor Block of the issued command
gg : Status Byte
hh : Sense Key
ii : Additional Sense Code
jj : Additional Sense Code Qualifier
kk-llll : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the disk array state, and remove the failure. Restart iSM server if
necessary.
Chapter 2 Message List
48
iSM03152: Management of control path by
autofind failed. file=<aaa...a>
command=(<bbb...b>)
status=(<cccccccc>)
detail=<dd-eeee>
[Classification] INFO
[Explanation] Failed in the inclusion of the control path by auto find function. The disk
information that becomes an error cannot be included in iSM server. iSM
server will ignore the error.
This message is output on UNIX system.
aaa...a : Special file name
bbb...b : Command Descriptor Block of the issued command
cccccccc : Status Byte
dd-eeee : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the disk array state, and remove the failure. Restart iSM server if
necessary.
iSM03152: Management of control path by
autofind failed. Disk=(disk<aaa>
(Port<bbb> Bus<ccc> Target<ddd>
Lun<eee>)) command=(<fff...f>)
status=(<gggggggg>) detail=<hh-iiii>
[Classification] INFO
[Explanation] Failed in the inclusion of the control path by auto find function. The disk
information that becomes an error cannot be included in iSM server. iSM
server will ignore the error.
This message is output on Windows system.
diskaaa (Portbbb Busccc Targetddd Luneee): Disk information
fff...f : Command Descriptor Block of the issued command
gggggggg : Status Byte
hh-iiii : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the disk array state, and remove the failure. Restart iSM server if
necessary.
Chapter 2 Message List
49
iSM03200: Control path access failed.
ip=<aaa...a> port=<bbbbb>
func=<ccc...c> errno=<ddd>
detail=<ee-ffff>
[Classification] ERROR
[Explanation] An error occurred in the socket communication with the disk array.
aaa...a : IP address
bbbbb : Port number
ccc...c : Function number
ddd : Error number
ee-ffff : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the network connection state to the disk array and the disk array state, and
remove the failure.
iSM03201: Control path access failed.
ip=<aaa...a> port=<bbbbb>
command=(<ccc...c>)
status=(<dd>/<ee>/<ff>/<gg>)
detail=<hh-iiii>
[Classification] ERROR
[Explanation] A command error occurred. A failure may exist in the disk array.
aaa...a : IP address
bbbbb : Port number
ccc...c : Command Descriptor Block of the issued command
dd : Status Byte
ee : Sense Key
ff : Additional Sense Code
gg : Additional Sense Code Qualifier
hh-iiii : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the disk array state, and remove the failure.
Chapter 2 Message List
50
iSM03203: Control path access failed.
ip=<aaa...a> port=<bbbbb>
func=<ccc...c> reason=(timeout
<ddd>sec.) detail=<ee-ffff>
[Classification] ERROR
[Explanation] A timeout occurred in the socket communication with the disk array.
aaa...a : IP address
bbbbb : Port number
ccc...c : Function number
ddd : Seconds of time out
ee-ffff : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the state of the network connection to the disk array and the state of the
disk array, and remove the failure.
iSM03204: Control path access failed.
ip=<aaa...a> port=<bbbbb>
reason=(invalid sequence)
detail=<cc-dddd>
[Classification] ERROR
[Explanation] Socket connection with the disk array has been disconnected.
aaa...a : IP address
bbbbb : Port number
cc-dddd : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the network setting for the disk array, and remove the failure.
Chapter 2 Message List
51
iSM03220: Control path access failed.
file=<aaa...a> func=<bbb...b>
errno=<ccc> detail=<dd-eeee>
[Classification] ERROR
[Explanation] Error occurred in the access of the control path (special file).
This message is output on UNIX system.
aaa...a : Special file name
bbb...b : Function number
ccc : Error number
dd-eeee : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the state of the FC connection to the disk array and the state of the disk
array, and remove the failure.
iSM03220: Control path access failed.
Disk=(disk<aaa> (Port<bbb>
Bus<ccc> Target<ddd> Lun<eee>))
func=<fff...f> errno=<ggg>
detail=<hh-iiii>
[Classification] ERROR
[Explanation] Error occurred in the access of the control path (disk).
This message is output on Windows system.
diskaaa (Portbbb Busccc Targetddd Luneee): Disk information
fff...f : Function number
ggg : Error number
hh-iiii : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the state of the FC connection to the disk array and the state of the disk
array, and remove the failure.
Chapter 2 Message List
52
iSM03221: Control path access failed.
file=<aaa...a> command=(<bbb...b>)
status=(<cc>/<dd>/<ee>/<ff>)
detail=<gg-hhhh>
[Classification] ERROR
[Explanation] A command error occurred. A failure may exist in the disk array.
This message is output on UNIX system.
aaa...a : Special file name
bbb...b : Command Descriptor Block of the issued command
cc : Status Byte
dd : Sense Key
ee : Additional Sense Code
ff : Additional Sense Code Qualifier
gg-hhhh : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the state of the disk array, and remove the failure.
iSM03221: Control path access failed.
Disk=(disk<aaa> (Port<bbb>
Bus<ccc> Target<ddd> Lun<eee>))
command=(<fff...f>)
status=(<gg>/<hh>/<ii>/<jj>)
detail=<kk-llll>
[Classification] ERROR
[Explanation] A command error occurred. A failure may exist in the disk array.
This message is output on Windows system.
diskaaa (Portbbb Busccc Targetddd Luneee): Disk information
fff...f : Command Descriptor Block of the issued command
gg : Status Byte
hh : Sense Key
ii : Additional Sense Code
jj : Additional Sense Code Qualifier
kk-llll : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the state of the disk array, and remove the failure.
Chapter 2 Message List
53
iSM03222: Control path access failed.
file=<aaa...a> command=(<bbb...b>)
status=(<cccccccc>)
detail=<dd-eeee>
[Classification] ERROR
[Explanation] A command error occurred. A failure may exist in the disk array.
This message is output on UNIX system.
aaa...a : Special file name
bbb...b : Command Descriptor Block of the issued command
cccccccc : Status Byte
dd-eeee : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the state of the FC connection to the disk array and the state of the disk
array, and remove the failure.
iSM03222: Control path access failed.
Disk=(disk<aaa> (Port<bbb>
Bus<ccc> Target<ddd> Lun<eee>))
command=(<fff...f>)
status=(<gggggggg>) detail=<hh-iiii>
[Classification] ERROR
[Explanation] A command error occurred. A failure may exist in the disk array.
This message is output on Windows system.
diskaaa (Portbbb Busccc Targetddd Luneee): Disk information
fff...f : Command Descriptor Block of the issued command
gggggggg : Status Byte
hh-iiii : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the state of the FC connection to the disk array and the state of the disk
array, and remove the failure.
Chapter 2 Message List
54
iSM03224: Control path is blockaded.
file=(<aaa...a>) func=<bbb...b>
errno=<ccccc> status=<ddd...d>
(<eee...e> productID=<fffff>
SN=<ggggg>) [UC=<hhhhhhhh>
FC=<ii>][_ALERT_]
[Classification] ERROR
[Explanation] The control path (access to special file) was blockaded.
This message is output on UNIX system.
This message is target of ESMPRO Manager Report, and also to be target of
ALIVE/Express Report via ESMPRO.
aaa...a : Special file name
bbb...b : Function number
ccccc : Error number
ddd...d : Result of issuing of SCSI command
eee...e : Disk array name
fffff : Product ID of disk array (S2100 Disk Array etc.)
ggggg : Serial number of disk array
hhhhhhhh/ii : Maintenance information
[Measures] Check the state of the FC connection to the disk array and the state of the disk
array, and remove the failure.
Chapter 2 Message List
55
iSM03224: Control path is blockaded.
disk=(disk<aaa> (Port<bbb>
Bus<ccc> Target<ddd> Lun<eee>))
func=<fff...f> errno=<ggggg>
status=<hhh...h> (<iii...i>
productID=<jjjjj> SN=<kkkkk>)
[UC=<llllllll> FC=<mm>][_ALERT_]
[Classification] ERROR
[Explanation] The control path (access to disk) was blockaded.
This message is output on Windows system.
This message is target of ESMPRO Manager Report, and also to be target of
ALIVE/Express Report via ESMPRO.
diskaaa (Portbbb Busccc Targetddd Luneee): Disk information
fff...f : Function number
ggggg : Error number
hhh...h : Result of issuing of SCSI command
iii...i : Disk array name
jjjjj : Product ID of disk array (S2100 Disk Array etc.)
kkkkk : Serial number of disk array
llllllll/mm : Maintenance information
[Measures] Check the state of the FC connection to the disk array and the state of the disk
array, and remove the failure.
Chapter 2 Message List
56
iSM03224: Control path is blockaded.
ip=(<aaa...a>) func=<bbb...b>
errno=<ccccc> status=<ddddd>
(<eee...e> productID=<fffff>
SN=<ggggg>) [UC=<hhhhhhhh>
FC=<ii>][_ALERT_]
[Classification] ERROR
[Explanation] The control path (access to SVP) was blockaded.
This message is target of ESMPRO Manager Report, and also to be target of
ALIVE/Express Report via ESMPRO.
aaa...a : IP address
bbb...b : Function number
ccccc : Error number
ddddd : Result of issuing of SCSI command
eee...e : Disk array name
fffff : Product ID of disk array (S2100 Disk Array etc.)
ggggg : Serial number of disk array
hhhhhhhh/ii : Maintenance information
[Measures] Check the state of the network connection to the disk array and the state of the
disk array, and remove the failure.
Chapter 2 Message List
57
iSM03225: Data can not be gotten sequentially
during split mode.Disk=(disk<aaa>
(Port<bbb> Bus<ccc> Target<ddd>
Lun<eee>)) reason=(invalid
sequence) detail=<ff-gggg>
[Classification] ERROR
[Explanation] Obtaining data failed in command divided transfer. The message indicates
that retry processing could not obtain correct data either.
diskaaa (Portbbb Busccc Targetddd Luneee): Disk information
ff-gggg : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the status of the disk array, and remove the failure. Restart monitoring
manually if necessary.
iSM03300: SVP has restarted. ip=<aaa...a>
detail=<bb-cccc>
[Classification] INFO
[Explanation] Service processor (SVP) has become available for use.
aaa...a : IP address of service processor(SVP)
bb-cccc : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Unnecessary
Chapter 2 Message List
58
iSM03301: SVP failed. name=(<aaa...a>)
ip=<bbb...b> detail=<cc-dddd>
[Classification] INFO
[Explanation] Service processor(SVP) has become unavailable for use due to a problem.
If SVP is in redundant composition, iSM server will continue processing by
switching the SVP.
aaa...a : Disk array name
bbb...b : IP address of service processor (SVP)
cc-dddd : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the state of SVP, and remove the failure.
iSM03302: UDP port is in use. SNMP trap can
not be collected. detail=<aa-bbbb>
[Classification] WARNING
[Explanation] The SNMP TRAP receiving is not possible because the SNMP TRAP receiving
port number 162 of the server operated by iSM server cannot be used.
Therefore, swift collecting of trouble information is not available, and it has to
be collected by polling. The port may be used by other application.
aa-bbbb : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] By making the port number 162 available to use, the SNMP TRAP receiving can
be done normally. Especially, it is easy to use the SNMP TRAP service on the
Windows system by installing it in the system and executing the environment
settings.
Chapter 2 Message List
59
iSM03303: SNMP trap has been available.
detail=<aa-bbbb>
[Classification] INFO
[Explanation] SNMP TRAP has changed the receiving status from unavailable to available.
SNMP TRAP receiving can be done. iSM server has become available to swiftly
report trouble information using SNMP TRAP.
aa-bbbb : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Unnecessary
iSM03400: File access failed. func=<aaa...a>
path=<bbb...b> errno=<ccc>
detail=<dd-eeee>
[Classification] ERROR
[Explanation] An error occurred in the file access function. The iSM server terminates
abnormally.
aaa...a : Function number
bbb...b : Path name
ccc : Error number
dd-eeee : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the function name and error number, and resolve the hindrance. Restart
the iSM serve if necessary.
Chapter 2 Message List
60
iSM03410: Socket access failed. func=<aaa...a>
errno=<bbb> detail=<cc-dddd>
[Classification] ERROR
[Explanation] Error occurred in the socket access function. iSM server will be terminated
abnormally.
aaa...a : Function number
bbb : Error number
cc-dddd : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the function name and error number, and resolve the hindrance. Restart
the iSM server if necessary.
iSM03411: Socket access failed. func=<aaa...a>
path=<bbb...b> errno=<ccc>
detail=<dd-eeee>
[Classification] ERROR
[Explanation] Error occurred in the socket access function. iSM server will be terminated
abnormally.
aaa...a : Function number
bbb...b : Socket path
ccc : Error number
dd-eeee : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the function name and error number, and resolve the hindrance. Restart
the iSM server if necessary.
Chapter 2 Message List
61
iSM03420: Memory access failed. func=<aaa...a>
errno=<bbb> detail=<cc-dddd>
[Classification] ERROR
[Explanation] Error occurred in the memory access function. iSM server will be terminated
abnormally.
This message is output on UNIX system.
aaa...a : Function number
bbb : Error number
cc-dddd : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the function name and error number, and resolve the hindrance. Restart
the iSM server if necessary.
iSM03430: System call error occurred.
func=<aaa...a> errno=<bbb...b>
detail=<cc-dddd>
[Classification] ERROR
[Explanation] Error occurred in the system function. iSM server will be terminated
abnormally.
This message is output on UNIX system.
aaa...a : Function number
bbb...b : Error number
cc-dddd : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the function name and error number, and resolve the hindrance. Restart
the iSM server if necessary.
Chapter 2 Message List
62
iSM03440: iSMmknod is running.
detail=<aa-bbbb>
[Classification] ERROR
[Explanation] iSM server cannot be activated because iSMmknod command is being executed.
This message is output on UNIX system.
aa-bbbb : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Wait for completion of iSMmknod command and restart the iSM server.
iSM03441: iSMmknod is not yet executed.
detail=<aa-bbbb>
[Classification] ERROR
[Explanation] It shows that auto_find_spf cannot start the iSM server because the iSMmknod
command is not yet executed (or not ended normally).
aa-bbbb : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Restart the iSM server after checking that iSMmknod command ended normally,
or after changing to the disk array connection to TCP/IP by deleting
auto_find_spf setting in the environment definition file.
iSM03442: iSMvollist is running.
detail=<aa-bbbb>
[Classification] ERROR
[Explanation] It shows that the iSM server cannot be started because iSMvollist command is
running.
aa-bbbb : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Restart the iSM server after iSMvollist command ended.
Chapter 2 Message List
63
iSM03500: Internal error occurred.
detail=<aa-bbbb>
[Classification] ERROR
[Explanation] Internal error has occurred under the agent management. The iSM server
terminates abnormally.
aa-bbbb : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Save the following information and restart the iSM server.
iSM operation log
syslog (for Unix)
event log (for Windows)
iSM03900: Process is busy when it terminates
emergency. Unexpected error
message maybe generated.
[Classification] WARNING
[Explanation] It indicates that the agent management detected an emergency stop, but the
process is unable to terminate immediately.
This message is output on Windows system.
[Measures] Unnecessary
Chapter 2 Message List
64
iSM04000 ∼
iSM04020: Function Error has occurred
name=<aaa...a> code=<bbbbb>
errno=<ccccc>
[Classification] NOTICE
[Explanation] It shows that a function error has occurred.
aaa...a : Function name
bbbbb : Internal code
ccccc : Error number
[Measures] Check the settings relevant to the applicable function.
iSM04021: Internal Error has occurred
code=<aaaaa> errno=<bbbbb>
[Classification] NOTICE
[Explanation] It shows that an internal error has occurred.
aaaaa : Internal code
bbbbb : Error number
[Measures] Check the server operation environment and the various settings.
iSM04022: Message send error has occurred
process=<aaa...a> reason=<bbb>
[Classification] WARNING
[Explanation] Failed in the transmission to the message queue.
This message is output on UNIX system. (Output only to syslog)
aaa...a : Process name
bbb : Reason of transmission failure
001 : Incorrect transmission demand data
002 : msgsnd() failure
003 : Others
[Measures] Check the server operation environment (system constant relevant to message
queue) and various settings.
Chapter 2 Message List
65
iSM04023: File write error has occurred
file=<aaa...a>
[Classification] ERROR
[Explanation] Failed in writing to the file.
aaa...a : File name
[Measures] Check the status of applicable file. (Writing down authority, etc.)
If a generation management file (iSM_Log.cnt) name is indicated, the generation
number managed by the generation management file is invalid, and backup
operation for the generation file may not be performed normally.
Terminate the iSM server, and then delete files under the directory containing the
log file in order to return it into the initial status. (Before deleting the files
under the directory, make the backup copies of the files if necessary.)
iSM04024: File read error has occurred
file=<aaa...a>
[Classification] ERROR
[Explanation] Failed in reading the file.
aaa...a : File name
[Measures] Check the status of applicable file. (Read out authority, etc.)
If a generation management file (iSM_Log.cnt) name is indicated, a generation
file is not created, and the log file may be overwritten.
Terminate the iSM server, and then delete files under the directory containing the
log file in order to return it into the initial status. (Before deleting the files
under the directory, make the backup copies of the files if necessary.)
Chapter 2 Message List
66
iSM04025: File open error has occurred
file=<aaa...a>
[Classification] ERROR
[Explanation] Failed in opening the file.
aaa...a : File name
[Measures] Check the existence and the status of the applicable file.
If a generation management file (iSM_Log.cnt) name is indicated, the generation
number managed by the generation management file is invalid, and backup
operation for the generation file may not be performed normally.
Terminate the iSM server, and then delete files under the directory containing the
log file in order to return it into the initial status. (Before deleting the files
under the directory, make the backup copies of the files if necessary.)
iSM04030: Last message repeated <aaa> times
[Classification] INFO
[Explanation] The same message is being output repeatedly.
aaa : Repeating time
[Measures] Unnecessary
iSM04040: Log File has swapped. The latest
backup=<aa>
[Classification] WARNING
[Explanation] The log file was swapped.
aa : The newest backup file number
[Measures] Unnecessary (This message indicates that the operation is executed normally.)
Chapter 2 Message List
67
iSM04060: Log File write started host=<aaa...a>
[Classification] INFO
[Explanation] It shows that writing into the operation log has started.
aaa...a : Host name of the machine running iSM server
[Measures] Unnecessary
Chapter 2 Message List
68
iSM06000 ∼
iSM06020: Function Error has occurred
name=<aaa...a> code=<bbbbb>
errno=<ccccc>
[Classification] NOTICE
[Explanation] It shows that a function error has occurred.
aaa...a : Function name
bbbbb : Internal code
ccccc : Error number
[Measures] Check the settings relevant to the applicable function.
iSM06021: Internal Error has occurred
code=<aaaaa> errno=<bbbbb>
[Classification] NOTICE
[Explanation] It shows that an internal error has occurred.
aaaaa : Internal code
bbbbb : Error number
[Measures] Check the server operation environment and various settings.
iSM06029: Message driven definition file does
not exist. file=<aaa...a>
[Classification] WARNING
[Explanation] It shows that message driven definition file does not exist.
aaa...a : File name
[Measures] If using the message driven function, take the action below.
For UNIX : Check the directory for storing the definition file and make the
file correctly.
For Windows: Set link information in the environment setting.
Chapter 2 Message List
69
iSM06030: Message driven definition file cannot
open. errno=<aaaaa> file=<bbb...b>
[Classification] WARNING
[Explanation] It shows that opening of the message driven definition file has failed.
aaaaa : Error number
bbb...b : File name
[Measures] Check the status of definition file. The definition files are stored in the
following:
For UNIX : /etc/iSMsvr/msgdrv.conf
For Windows: installation directory\conf\iSMsvr\msgdrv.conf
iSM06031: Message driven definition file cannot
read. line=<aaa> errno=<bbbbb>
[Classification] WARNING
[Explanation] It indicates that reading the message driven definition file has failed.
aaa : Error line number
bbbbb : Error number
[Measures] Check the status of the definition file (such as the reading authority). The
definition files are stored in the following:
For UNIX : /etc/iSMsvr/msgdrv.conf
For Windows: installation directory\conf\iSMsvr\msgdrv.conf
iSM06032: Message driven definition file error.
First line is not “[SERVER]”
[Classification] WARNING
[Explanation] It indicates that the first line of message driven definition file is not [SERVER].
[Measures] Take the measures below.
For UNIX : The header should be [SERVER]. Check the content of the file.
For Windows: Check the link information in the environment setting, and
specify the setting again.
Chapter 2 Message List
70
iSM06033: Message driven definition file error.
<aaa...a> overlaps. line=<bbb>
[Classification] WARNING
[Explanation] It indicates that “SMTP”, “SMTP_PORT”, “POP”, “POP_PORT”, “AUTH”,
“USER”, “PASSWORD”, or “HEADER” overlaps in the message driven
definition file.
aaa...a : “SMTP”, “SMTP_PORT”, “POP”, “POP_PORT”, “AUTH”,
“USER”, “PASSWORD”, or “HEADER”
bbb : Error line number
[Measures] Take the measures below.
For UNIX : Check the syntax of the definition file and describe it correctly.
For Windows: Check the link information in the environment setting, and
specify the setting again.
iSM06034: Message driven definition file error.
First word is not keyword. line=<aaa>
[Classification] WARNING
[Explanation] It indicates that it is the applicable line of message driven definition file and the
first word is not a keyword.
aaa : Error line number
[Measures] Take the measures below.
For UNIX : Check the syntax of the definition file and describe it correctly.
For Windows: Check the link information in the environment setting, and
specify the setting again.
Chapter 2 Message List
71
iSM06035: Message driven definition file error.
‘=’ does not exist. line=<aaa>
[Classification] WARNING
[Explanation] It indicates that there is no “=” in the applicable line of the message driven
definition file.
aaa : Error line number
[Measures] Take the measures below.
For UNIX : Check the syntax of the definition file and describe it correctly.
For Windows: Check the link information in the environment setting, and
specify the setting again.
iSM06036: Message driven definition file error.
Parentheses are not matched.
line=<aaa>
[Classification] WARNING
[Explanation] It indicates that the parenthesis is not suitable for the applicable line of the
message driven definition file.
aaa : Error line number
[Measures] Take the measures below.
For UNIX : Check the syntax of the definition file and describe parentheses
correctly.
For Windows: Check the link information in the environment setting, and
specify the setting again.
Chapter 2 Message List
72
iSM06037: Message driven definition file error.
<aaa...a> is not defined
[Classification] WARNING
[Explanation] It indicates that there is no definition of “SMTP”, “POP”, or “USER” in the
message driven definition file.
aaa...a : “SMTP”, “POP”, or “USER”
[Measures] Take the measures below.
For UNIX : Check the syntax of the definition file and describe SMTP, POP,
or USER definition correctly.
For Windows: Check the link information in the environment setting, and
specify the setting again.
iSM06038: Message driven definition file error.
Exceed 256 bytes. line=<aaa>
[Classification] WARNING
[Explanation] It indicates that the applicable line of the message driven definition file exceeded
256 bytes.
aaa : Error line number
[Measures] Take the measures below.
For UNIX : Check the applicable line of the definition file and describe it
within 256 bytes.
For Windows: Check the link information in the environment setting, and
specify the setting again.
Chapter 2 Message List
73
iSM06039: Message driven definition file error.
“shell” and “mail” exceeded 10.
line=<aaa>
[Classification] WARNING
[Explanation] It indicates that definition number of either “shell” or “mail” at the same level
exceeded 10 in the applicable line of the message driven definition file.
aaa : Error line number
[Measures] Take the measures below.
For UNIX : Check the applicable line of the definition file and reduce the
description number of definition.
For Windows: Check the link information in the environment setting, and
specify the setting again.
iSM06040: Header file cannot open.
errno=<aaaaa>
[Classification] WARNING
[Explanation] It indicates that opening a header file has failed.
aaaaa : Error number
[Measures] Check header file name (header file name specified in message driven definition
file on UNIX system, or mail header file name specified in link information of
environment settings on Windows system), and check presence/absence and
status of file.
Chapter 2 Message List
74
iSM06041: Header file cannot read.
errno=<aaaaa>
[Classification] WARNING
[Explanation] It indicates that reading a header file has failed.
aaaaa : Error number
[Measures] Check header file name (header file name specified in message driven definition
file on UNIX system, or mail header file name specified in link information of
environment settings on Windows system), and check the state of the file (such
as reading authority, etc.).
iSM06042: Header file’s mail-body size over
1024 bytes
[Classification] WARNING
[Explanation] It indicates that the mail-body size of header file was over 1024 bytes.
[Measures] Check header file name (header file name specified in message driven definition
file on UNIX system, or mail header file name specified in link information of
environment settings on Windows system), and reduce the mail-body size.
iSM06043: Header file error. First line does not
begin with “FROM:”
[Classification] WARNING
[Explanation] It indicates that the first line of the header file does not start with “FROM:”.
[Measures] Check header file name (header file name specified in message driven definition
file on UNIX system, or mail header file name specified in link information of
environment settings on Windows system), and check the first line of the file.
Chapter 2 Message List
75
iSM06044: Header file error. No character
following “FROM:”
[Classification] WARNING
[Explanation] It indicates that nothing is written next to first “FROM:” in the header file.
[Measures] Check header file name (header file name specified in message driven definition
file on UNIX system, or mail header file name specified in link information of
environment settings on Windows system), and check the first line of the file.
iSM06045: Header file error. Line exceeds 256
bytes. line=<aaa>
[Classification] WARNING
[Explanation] It indicates that the applicable line of header file exceeds 256 bytes.
aaa : Error line number
[Measures] Check header file name (header file name specified in message driven definition
file on UNIX system, or mail header file name specified in link information of
environment settings on Windows system), and check the applicable line of the
file and describe it within 256 bytes.
iSM06047: SMTP address or port number error
[Classification] WARNING
[Explanation] It indicates that the specified SMTP address or the port number specified in
SMTP_PORT is incorrect.
[Measures] Specify SMTP by the DNS name or IP address of the SMTP server and
SMTP_PORT by the port number of the SMTP server.
Chapter 2 Message List
76
iSM06048: POP address or port number error
[Classification] WARNING
[Explanation] It indicates that the specified POP address or the port number specified in
POP_PORT is incorrect.
[Measures] Specify POP by the DNS name of IP address of the POP server and POP_PORT
by the port number of the POP server.
iSM06050: Shell file does not exist. file=<aaa...a>
[Classification] WARNING
[Explanation] It indicates that shell file does not exist.
aaa...a : File name
[Measures] A shell file (shell file specified in message driven definition file on UNIX system,
or shell file specified in link information of environment settings on Windows
system) must be created in advance for preparation.
iSM06051: Shell file is not executable.
file=<aaa...a>
[Classification] WARNING
[Explanation] It indicates that shell file cannot be executed.
aaa...a : File name
[Measures] A shell file (shell file specified in message driven definition file on UNIX system,
or shell file specified in link information of environment settings on Windows
system) does not have the execution authority. The shell file must be
authorized to be executed as a shell.
Chapter 2 Message List
77
iSM06062: Mail server connect error.
name=<aaa...a> code=<bbbbb>
errno=<ccccc>
[Classification] WARNING
[Explanation] It indicates that the connection to mail server has failed.
aaa...a : Function name
bbbbb : Internal code
ccccc : Error number
[Measures] Failed in connection with mail server (mail server specified in message driven
definition file on UNIX system, or mail server specified by link information of
environment settings on Windows system). Check addresses and operations of
defined mail server.
iSM06063: Recv error (from mail server).
name=<aaa...a> code=<bbbbb>
errno=<ccccc>
[Classification] WARNING
[Explanation] It indicates that receiving from the mail server has failed.
aaa...a : Function name
bbbbb : Internal code
ccccc : Error number (0 indicates that the socket communication via
SMTP server is closed.)
[Measures] Check the operation of the defined mail server, and resolve the problem.
Chapter 2 Message List
78
iSM06064: Send error (to mail server).
name=<aaa...a> code=<bbbbb>
errno=<ccccc>
[Classification] WARNING
[Explanation] It indicates that transmitting to mail server has failed.
aaa...a : Function name
bbbbb : Internal code
ccccc : Error number
[Measures] Check the operation of the defined mail server, and resolve the problem.
iSM06065: Communication error(mail server).
id=<a> send=<bbb...b> recv=<ccc...c>
[Classification] WARNING
[Explanation] It indicates that the communication error occurred with mail server.
a : Internal code number
bbb...b : Transmission information
ccc...c : Reception information
[Measures] Check the operation of the defined mail server, and resolve the problem based on
the information.
iSM06066: Mail server time out
[Classification] WARNING
[Explanation] It indicates that the operation of the mail server is slow and going to timeout.
[Measures] Check the operation of the defined mail server, and consider the restriction of
mail volume, the operation of mail sever and path’s communication speed.
Chapter 2 Message List
79
iSM06068: Authentication failed. id=<a>
send=<bbb...b> recv=<ccc...c>
[Classification] WARNING
[Explanation] It indicates that authentication has failed.
a : Internal code
bbb...b : Transmission information
ccc...c : Reception information
[Measures] Take the measures described below.
For UNIX : Check the required information for the specified authentication
mode, and describe it correctly.
For Windows: Check the required information for the specified authentication
mode, and set the link information in the environment setting
again.
iSM06070: Message buffer is full. Data lost
detected
[Classification] WARNING
[Explanation] It indicates that messages have been deleted because the message buffer capacity
exceeded the limit.
This message is output on UNIX system. (Output only to syslog)
[Measures] There are too many messages for link. Definition must be reviewed.
Chapter 2 Message List
80
iSM06071: Data lost recovered
[Classification] WARNING
[Explanation] It indicates that the message lost by the overflow of message buffer has been
recovered.
This message is output on UNIX system. (Output only to syslog)
[Measures] This message is output in pair with iSM06070, which indicates that too many
messages to be linked exist, and indicates recovery of the error indicated by
iSM06070. Refer to iSM06070 for the recovery processing.
iSM06080: Definition change is successful
[Classification] INFO
[Explanation] It indicates that the definition change was successful.
[Measures] Unnecessary (Normal operation).
iSM06081: Definition change error. Message
driven function does not start
[Classification] WARNING
[Explanation] It indicates that it failed to change the definition. The driven function does not
operate till it succeeds.
[Measures] While trying to change the definition with the iSM server running, the definition
error occurred. Correct the definition error and execute the change command
again.
Chapter 2 Message List
81
iSM06082: Definition change error. Message
driven function continues to operate
by previous definition
[Classification] WARNING
[Explanation] The definition change was failed. The driven function operates by the old
function before changing.
[Measures] While trying to change the definition with iSM server operating, the definition
error occurred. Correct the definition error and execute the change command
again.
iSM06083: Making directory for core dump file
error. code=<aaaaa> path=<bbb...b>
errno=<ccccc>
[Classification] ERROR
[Explanation] It indicates that it failed to create directory to output core dump file.
aaaaa : Code number
bbb...b : Directory name
ccccc : Error number
[Measures] There is an error in the authority of installation directory and so on.
iSM06084: Change directory error.name=
<aaa...a> path=<bbb...b>
errno=<ccccc>
[Classification] ERROR
[Explanation] It indicates that the directory change has been failed.
aaa...a : Function name
bbb...b : Directory name
ccccc : Error number
[Measures] There is an error in the authority of installation directory and so on.
Chapter 2 Message List
82
iSM06085: Making directory for message file
error. name=<aaa...a> path=<bbb...b>
errno=<ccccc>
[Classification] ERROR
[Explanation] It indicates it failed to create the message file directory.
aaa...a : Function name
bbb...b : Directory name
ccccc : Error number
[Measures] There is an error in the authority of installation directory and so on.
iSM06086: Mail process count over. This
message is canceled. msg=<aaa...a>
[Classification] WARNING
[Explanation] The mail of the applicable message could not be transmitted, because the
processing number of mail transmission and shell start per one minute exceeded
the limit. The driving process stops for maximum of one minute, and the driving
to the message occurred during stop process is not executed.
aaa...a : Message
[Measures] Number of mails and shell start by driving is too much. The definition should be
reviewed, or the way of mail transmission or shell start operating method should
be considered.
iSM06087: Shell process count over. This
message is canceled. msg=<aaa...a>
[Classification] WARNING
[Explanation] The shell start of the applicable message could not be executed, because the
processing number of mail transmission and shell start per one minute exceeded
the limit. The driving process stops for maximum of one minute, and the
driving to the message occurred during stop process is not executed.
aaa...a : Message
[Measures] Number of mails and shell start by driving is too much. The definition should
be reviewed, or the way of mail transmission or shell start operating method
should be considered.
Chapter 2 Message List
83
iSM06088: Message driven processing stopped
for excess of number of processes
was resumed
[Classification] WARNING
[Explanation] The driving process, which has been cancelled because the processing number of
mail transmission and shell start per one minute exceeded the limit, has been
released.
[Measures] Take the measures according to messages of iSM06086 and iSM06087 that
appear at the same time.
iSM06091: Message driven definition file error.
Syntax error existed. line=<aaa>
[Classification] WARNING
[Explanation] It indicates that there is keyword error in the applicable line of the message
driven definition file.
aaa : Error line number
[Measures] Take the measures below.
For UNIX : Check the applicable line of the message driven definition file
and correct the definition.
For Windows: Check the link information in the environment setting, and
specify the setting again.
Chapter 2 Message List
84
iSM06092: Message driven definition file error.
Number of “,” is not right. line=<aaa>
[Classification] WARNING
[Explanation] It indicates that “ , ” is not suitable in the applicable line of the message driven
definition file.
aaa : Error line number
[Measures] Take the measures below.
For UNIX : Check the applicable line of the message driven definition file
and correct the definition.
For Windows: Check the link information in the environment setting, and
specify the setting again.
iSM06093: Message driven definition file error.
“HEADER” is not defined
[Classification] WARNING
[Explanation] It indicates that “HEADER” is required but it is not defined in the message
driven definition file.
[Measures] Take the measures below.
For UNIX : Check the applicable line of the message driven definition file
and modify the definition.
For Windows: Check the link information in the environment setting, and
specify the setting again.
Chapter 2 Message List
85
iSM06099: Message driven definition file error.
id=<a> line=<bbb>
[Classification] WARNING
[Explanation] It indicates that incorrect description exists in the message driven definition file.
a : Error Classification
0 : Some character follows the [SERVER] or [LEVEL].
1 : A position of “=” is inappropriate or “=” does not exist.
2 : No character follows “=”.
3 : Invalid character exists in the end of line.
4 : A position of “ ) ” is inappropriate.
5 : A position of “,” is inappropriate.
6 : A position of “ " ” is inappropriate.
7 : A position of “shell(” or “mail(” is inappropriate.
8 : The description of file name or address does not exist.
9 : Non-numeric character exists in the port number (SMTP_PORT or
POP_PORT).
10 : Incorrect authentication type is specified for AUTH.
bbb : Error line number
[Measures] Take the measures below.
For UNIX : Check the applicable line of the message driven definition file
and describe the correct definition.
For Windows: Check the link information in the environment setting, and
specify the setting again.
Chapter 2 Message List
86
iSM06902: Message customize function error.
reason=<aaa...a> [func=<bbb...b>]
[errno=<ccc>] [line=<ddd>]
[detail=<eee...e>]
[Classification] ERROR
[Explanation] It shows that an error occurred in the message customizing function.
This message is output on Windows system.
aaa...a : error contents
system call error : System call error
file definition error : File description error
internal error : Internal error
bbb...b : System function name
ccc : Error number
ddd : Error line number
eee...e : Detailed information
message ID not found : No valid message ID
Double definition of message ID : Message ID defined duplicately
value of registry is wrong : Invalid registry
[Measures] Take appropriate measures after confirming the error contents, and restart the
iSM server.
Chapter 2 Message List
87
iSM07000 ∼
iSM07011: Resource monitoring started.
(<aaa...a> productID=<bbbbb>
SN=<ccccc>)
[Classification] INFO
[Explanation] It indicates that state monitoring to disk array (name: aaa...a) has been started.
For Windows, this message is target of ESMPRO Manager Report.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
[Measures] Unnecessary
iSM07012: Resource monitoring started.
(<aaa...a> productID=<bbbbb>
SN=<ccccc>) [UC=<dddddddddd>
FC=<ee>][_ALERT_]
[Classification] INFO
[Explanation] It indicates that state monitoring to disk array (name: aaa...a) started. This
message is output at start from the fault status.
For Windows, this message is target of ESMPRO Manager Report, and also to
be target of ALIVE/Express Report via ESMPRO.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddddddddd/ee : Maintenance information
[Measures] Unnecessary
Chapter 2 Message List
88
iSM07021: Resource monitoring stopped.
(<aaa...a> productID=<bbbbb>
SN=<ccccc>)
[Classification] INFO
[Explanation] It indicates that state monitoring to disk array (name: aaa...a) has been stopped.
For Windows, this message is target of ESMPRO Manager Report.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
[Measures] Unnecessary
iSM07022: Resource monitoring stopped for
maintenance. (<aaa...a>
productID=<bbbbb> SN=<ccccc>)
[Classification] INFO
[Explanation] It indicates that state monitoring to disk array (name: aaa...a) was stopped
because the status of maintenance operation was detected.
For Windows, this message is target of ESMPRO Manager Report.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
[Measures] Unnecessary (after the end of maintenance operation, the monitoring is
automatically restarted.)
Chapter 2 Message List
89
iSM07023: Resource monitoring stopped by
control path fault. (<aaa...a>
productID=<bbbbb> SN=<ccccc>)
[UC=<dddddddddd>
FC=<ee>][_ALERT_]
[Classification] ERROR
[Explanation] It indicates that trouble of control path caused the stop of monitoring to disk
array (name: aaa...a).
For Windows, this message is target of ESMPRO Manager Report, and also to
be target of ALIVE/Express Report via ESMPRO.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddddddddd/ee : Maintenance information
[Measures] Investigate the cause from related other messages and restart the monitoring after
the trouble recovery. The monitoring can be restarted from iSM client.
Chapter 2 Message List
90
iSM07024: Resource monitoring stopped by
information collecting failure.
(<aaa...a> productID=<bbbbb>
SN=<ccccc>) [UC=<dddddddddd>
FC=<ee>][_ALERT_]
[Classification] ERROR
[Explanation] It indicates that state monitoring to disk array (name: aaa...a) has been stopped
by information collecting failure.
For Windows, this message is target of ESMPRO Manager Report, and also to
be target of ALIVE/Express Report via ESMPRO.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddddddddd/ee : Maintenance information
[Measures] Specify the cause with related other messages and restart the monitoring after the
trouble recovery.
iSM07025: Resource monitoring stopped for
configuration. (<aaa...a>
productID=<bbbbb> SN=<ccccc>)
[Classification] INFO
[Explanation] It indicates that state monitoring to disk array (name: aaa...a) has been stopped
with the start of configuration setting.
For Windows, this message is target of ESMPRO Manager Report.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
[Measures] Start monitoring if necessary after configuration setting is complete. Restart
can be selected also.
Chapter 2 Message List
91
iSM07026: Resource monitoring changes to
recovery mode.(<aaa...a>
productID=<bbbbb> SN=<ccccc>)
[UC=<dddddddddd>
FC=<ee>][_ALERT_]
[Classification] ERROR
[Explanation] It indicates that the monitoring for the disk array (name: aaa...a) became
impossible to continue due to disk array failure or control path failure, and the
system is turned into the monitoring recovery waiting status.
For Windows, this message is target of ESMPRO Manager Report, and also to
be target of ALIVE/Express Report via ESMPRO.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddddddddd/ee : Maintenance information
[Measures] Monitoring will be restarted automatically if the failure is a temporary failure.
Take appropriate measures if monitoring will not restart automatically even after
waiting for a while. There may be a permanent failure for control path.
iSM07031: Request to stop server is waiting for
termination of configuration.
[Classification] INFO
[Explanation] It indicates that server termination request is placed in wait status until
configuration setting is over.
[Measures] The server is automatically terminated once configuration setting is over. To
forcibly terminate the server, execute forcible termination of the server.
Chapter 2 Message List
92
iSM07032: Request to stop monitoring resource
is waiting for termination of other
request. (<aaa...a>)
[Classification] INFO
[Explanation] It indicates that a state monitoring stop command to disk array (name: aaa...a) is
waiting for the end of other command processing. The monitoring of disk array
automatically stops after the end of the processing that has been requested.
aaa...a : Disk array name
[Measures] Unnecessary
iSM07033: Request to start monitoring resource
is accepted. (<aaa...a>)
[Classification] INFO
[Explanation] It indicates that request for starting state monitoring to disk array (name: aaa...a)
is accepted.
aaa...a : Disk array name
[Measures] Unnecessary
iSM07034: Request to stop monitoring resource
is accepted. (<aaa...a>)
[Classification] INFO
[Explanation] It indicates that request for stopping state monitoring to disk array (name: aaa...a)
is accepted.
aaa...a : Disk array name
[Measures] Unnecessary
Chapter 2 Message List
93
iSM07035: Retrying to start monitoring resource
is started. (<aaa...a>)
[Classification] INFO
[Explanation] It indicates that an attempt has been made to restart state monitoring to disk array
(name: aaa...a) that stopped operation due to failure.
aaa...a : Disk array name
[Measures] Unnecessary
iSM07091: Control path access to <aaa...a>
failed. (status=<bbbb>h/<cc>h/
<dddddddd>h/<eeeeeeee>h/<ffffff>h)
[Classification] WARNING
[Explanation] It indicates that the administration command to disk array (name: aaa...a) ended
due to an error.
aaa...a : Disk array name
bbbb/cc/dddddddd/eeeeeeee/ffffff : Status Code
[Measures] Check whether the trouble of disk array or the access path failure between disk
array and server occurs.
iSM07092: Collecting information failed.
(<aaa...a>)
[Classification] WARNING
[Explanation] It indicates that it failed to generate information about disk array (name: aaa...a).
aaa...a : Disk array name
[Measures] Specify the cause from related other messages and restart the monitoring after
the trouble recovery. The monitoring can be restarted from iSM client.
Chapter 2 Message List
94
iSM07093: Monitoring function is blockaded.
[Classification] ERROR
[Explanation] It indicates that state monitoring to the iSM server is blockaded.
[Measures] Collect information and restart the iSM server if necessary. For how to collect
the information, refer to “Information Gathering Method when Server Fault with
Unknown Cause” of the “User’s Manual”.
iSM07094: Illegal data has detected. (<aaa...a>
productID=<bbbbb> SN=<ccccc>
status=<ddddd>h/<eeeee>h)
[Classification] ERROR
[Explanation] It indicates that a response from disk array (name: aaa...a) is illegal.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
ddddd/eeeee : Status code
[Measures] Check the status of the faulty disk array and perform the appropriate
maintenance.
Chapter 2 Message List
95
iSM07095: Inconsistency of resources
information(<aaaaa>) was detected.
(<bbb...b> productID=<ccccc>
SN=<ddddd>)
[Classification] ERROR
[Explanation] It indicates that inconsistency of configuration information is detected in
resource (aaaaa) of disk array (name: bbb...b).
aaaaa : Resource type (LD, etc.)
bbb...b : Disk array name
ccccc : Product ID of disk array (S2100 Disk Array etc.)
ddddd : Serial number of disk array
[Measures] Check the resource with incorrect configuration, and correct the configuration.
Chapter 2 Message List
96
iSM07101: State of PD(<aa>h) has become ready.
(<bbb...b> productID=<ccc...c>
SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>)
[Classification] INFO
[Explanation] It indicates that the physical disk (number: ee-ff) of disk array (name: bbb...b)
has become ready.
aa : Internal number indicating physical disk type
bbb...b : Disk array name
ccc...c : Product ID of disk array (S4300 Disk Array etc.)
ddd...d : Serial number of disk array
ee-ff : Physical disk number
ggg...g : Information of RANK or pool where the physical disk belongs
- PoolNo=<xxxx>h PoolName=<yyy...y>
Indicates pool information. (for the disk arrays with pool)
xxxx : Pool number
yyy...y : Pool name
- RankNo=<xx>h-<yy>h
Indicates RANK information. (for other than the disk arrays
with pool)
xx-yy : RANK number
[Measures] Unnecessary
Chapter 2 Message List
97
iSM07102: State of PD(<aa>h) has become fault.
(<bbb...b> productID=<ccc...c>
SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>)[_ALERT_]
[Classification] ERROR
[Explanation] It indicates that trouble occurred in the physical disk (number: ee-ff) of disk
array (name: bbb...b).
For Windows, this message is target of ESMPRO Manager Report.
aa : Internal number indicating physical disk type
bbb...b : Disk array name
ccc...c : Product ID of disk array (S4300 Disk Array etc.)
ddd...d : Serial number of disk array
ee-ff : Physical disk number
ggg...g : Information of RANK or pool where the physical disk belongs
- PoolNo=<xxxx>h PoolName=<yyy...y>
Indicates pool information. (for the disk arrays with pool)
xxxx : Pool number
yyy...y : Pool name
- RankNo=<xx>h-<yy>h
Indicates RANK information. (for other than the disk arrays
with pool)
xx-yy : RANK number
[Measures] Check the status of resource with the trouble and perform the appropriate
maintenance.
Chapter 2 Message List
98
iSM07104: State of PD(<aa>h) has become
attn(rebuilding). (<bbb...b>
productID=<ccc...c> SN=<ddd...d>
No=<ee>h-<ff>h <ggg...g>)[_ALERT_]
[Classification] NOTICE
[Explanation] It indicates that the physical disk (number: ee-ff) of disk array (name: bbb...b) is
rebuilding data.
For Windows, this message is target of ESMPRO Manager Report.
aa : Internal number indicating physical disk type
bbb...b : Disk array name
ccc...c : Product ID of disk array (S4300 Disk Array etc.)
ddd...d : Serial number of disk array
ee-ff : Physical disk number
ggg...g : Information of RANK or pool where the physical disk belongs
- PoolNo=<xxxx>h PoolName=<yyy...y>
Indicates pool information. (for the disk arrays with pool)
xxxx : Pool number
yyy...y : Pool name
- RankNo=<xx>h-<yy>h
Indicates RANK information. (for other than the disk arrays
with pool)
xx-yy : RANK number
[Measures] Unnecessary
Chapter 2 Message List
99
iSM07105: State of PD(<aa>h) has become
attn(powering up). (<bbb...b>
productID=<ccc...c> SN=<ddd...d>
No=<ee>h-<ff>h <ggg...g>)
[Classification] NOTICE
[Explanation] It indicates that the physical disk (number: ee-ff) of disk array (name: bbb...b) is
starting up.
aa : Internal number indicating physical disk type
bbb...b : Disk array name
ccc...c : Product ID of disk array (S4300 Disk Array etc.)
ddd...d : Serial number of disk array
ee-ff : Physical disk number
ggg...g : Information of RANK or pool where the physical disk belongs
- PoolNo=<xxxx>h PoolName=<yyy...y>
Indicates pool information. (for the disk arrays with pool)
xxxx : Pool number
yyy...y : Pool name
- RankNo=<xx>h-<yy>h
Indicates RANK information. (for other than the disk arrays
with pool)
xx-yy : RANK number
[Measures] Unnecessary (It usually becomes ready within a few seconds. If the status does
not become ready, perform the appropriate maintenance because some trouble
may occur).
Chapter 2 Message List
100
iSM07106: State of PD(<aa>h) has become
attn(formatting). (<bbb...b>
productID=<ccc...c> SN=<ddd...d>
No=<ee>h-<ff>h <ggg...g>)
[Classification] NOTICE
[Explanation] It indicates that the physical disk (number: ee-ff) of disk array (name: bbb...b) is
being formatted.
aa : Internal number indicating physical disk type
bbb...b : Disk array name
ccc...c : Product ID of disk array (S4300 Disk Array etc.)
ddd...d : Serial number of disk array
ee-ff : Physical disk number
ggg...g : Information of RANK or pool where the physical disk belongs
- PoolNo=<xxxx>h PoolName=<yyy...y>
Indicates pool information. (for the disk arrays with pool)
xxxx : Pool number
yyy...y : Pool name
- RankNo=<xx>h-<yy>h
Indicates RANK information. (for other than the disk arrays
with pool)
xx-yy : RANK number
[Measures] Unnecessary
Chapter 2 Message List
101
iSM07108: State of PD(<aa>h) has become
offline. (<bbb...b>
productID=<ccc...c> SN=<ddd...d>
No=<ee>h-<ff>h <ggg...g>)
[Classification] ERROR
[Explanation] It indicates that the physical disk (number: ee-ff) of disk array (name: bbb...b)
has been in the off line status.
aa : Internal number indicating physical disk type
bbb...b : Disk array name
ccc...c : Product ID of disk array (S4300 Disk Array etc.)
ddd...d : Serial number of disk array
ee-ff : Physical disk number
ggg...g : Information of RANK or pool where the physical disk belongs
- PoolNo=<xxxx>h PoolName=<yyy...y>
Indicates pool information. (for the disk arrays with pool)
xxxx : Pool number
yyy...y : Pool name
- RankNo=<xx>h-<yy>h
Indicates RANK information. (for other than the disk arrays
with pool)
xx-yy : RANK number
[Measures] Check the physical disk in which the state transition occurred, and perform the
appropriate maintenance.
Chapter 2 Message List
102
iSM07109: State of PD(<aa>h) has become ready.
(<bbb...b> productID=<ccc...c>
SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>)[_ALERT_]
[Classification] INFO
[Explanation] It indicates that the physical disk (number: ee-ff) of disk array (name: bbb...b)
has rebuilt data and its status has changed to “ready”.
For Windows, this message is target of ESMPRO Manager Report.
aa : Internal number indicating physical disk type
bbb...b : Disk array name
ccc...c : Product ID of disk array (S4300 Disk Array etc.)
ddd...d : Serial number of disk array
ee-ff : Physical disk number
ggg...g : Information of RANK or pool where the physical disk belongs
- PoolNo=<xxxx>h PoolName=<yyy...y>
Indicates pool information. (for the disk arrays with pool)
xxxx : Pool number
yyy...y : Pool name
- RankNo=<xx>h-<yy>h
Indicates RANK information. (for other than the disk arrays
with pool)
xx-yy : RANK number
[Measures] Unnecessary
Chapter 2 Message List
103
iSM07111: State of <aaaaa>(<bb>h[-<cc>h]) has
become ready. (<ddd...d>
productID=<eeeee> SN=<fffff>
No=<gg>h )
[Classification] INFO
[Explanation] It indicates that the component* (abbreviated name: aaaaa, number: gg) of disk
array (name: ddd...d) has become ready.
aaaaa : Abbreviated name of component
bb-cc : Internal number indicating component type
ddd...d : Disk array name
eeeee : Product ID of disk array (S2100 Disk Array etc.)
fffff : Serial number of disk array
gg : Component number
*except for logical disk/physical disk
[Measures] Unnecessary
iSM07112: State of <aaaaa>(<bb>h[-<cc>h]) has
become fault. (<ddd...d>
productID=<eeeee> SN=<fffff>
No=<gg>h )[_ALERT_]
[Classification] ERROR
[Explanation] It indicates that trouble occurred in the component* (abbreviated name: aaaaa,
number: gg) of disk array (name: ddd...d).
For Windows, this message is target of ESMPRO Manager Report.
aaaaa : Abbreviated name of component
bb-cc : Internal number indicating component type
ddd...d : Disk array name
eeeee : Product ID of disk array (S2100 Disk Array etc.)
fffff : Serial number of disk array
gg : Component number
*except for logical disk/physical disk
[Measures] Check the status of the resource with the trouble and perform the appropriate
maintenance.
Chapter 2 Message List
104
iSM07113: State of <aaaaa>(<bb>h[-<cc>h]) has
become offline. (<ddd...d>
productID=<eeeee> SN=<fffff>
No=<gg>h )
[Classification] ERROR
[Explanation] It indicates that the component* (abbreviated name: aaaaa, number: gg) of disk
array (name: ddd...d) has become removed (or not existed).
aaaaa : Abbreviated name of component
bb-cc : Internal number indicating component type
ddd...d : Disk array name
eeeee : Product ID of disk array (S2100 Disk Array etc.)
fffff : Serial number of disk array
gg : Component number
*except for logical disk/physical disk
[Measures] Check the resource in which the state transition occurred, and perform the
appropriate maintenance.
iSM07114: State of HD(<aa>h) has become
attn(nolicense). (<bbb...b>
productID=<ccccc> SN=<ddddd>
No=<ee>h )
[Classification] NOTICE
[Explanation] The program product BaseProduct has not been installed, and the host director
(number: ee) of the disk array (name: bbb...b) is not available.
aa : Internal number indicating the type of the component
bbb...b : Disk array name
ccccc : Product ID of the disk array (S2200 Disk Array etc.)
ddddd : Serial number of disk array
ee : Component number
[Measures] Install the program product BaseProduct for the host director.
Chapter 2 Message List
105
iSM07115: State of CHE(<aa>h[-<bb>h]) has
become attn(rebuilding). (<ccc...c>
productID=<ddd...d> SN=<eee...e>
No=<ff>h )
[Classification] NOTICE
[Explanation] It indicates that the cache module (number: ff) of a disk array (name: ccc...c) is
rebuilding data.
aa-bb : Internal number indicating component type
ccc...c : Disk array name
ddd...d : Product ID of disk array (S2800 Disk Array etc.)
eee...e : Serial number of disk array
ff : Component number
[Measures] Unnecessary
iSM07116: State of DAC_BBU(<aa>h[-<bb>h])
has become attn(charge). (<ccc...c>
productID=<ddd...d> SN=<eee...e>
No=<ff>h )
[Classification] NOTICE
[Explanation] It indicates the battery (number: ff) of disk array (name: ccc...c) is charging.
aa-bb : Internal number indicating component type
ccc...c : Disk array name
ddd...d : Product ID of disk array (S2800 Disk Array etc.)
eee...e : Serial number of disk array
ff : Component number
[Measures] Unnecessary
Chapter 2 Message List
106
iSM07121: State of LD has become ready.
(<aaa...a> productID=<bbbbb>
SN=<ccccc> No=<dddd>h
Name=<eee...e>)
[Classification] INFO
[Explanation] It indicates that the logical disk (number: dddd, name: eee...e) of disk array
(name: aaa...a) has become ready.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] Unnecessary
iSM07122: State of LD has become fault.
(<aaa...a> productID=<bbbbb>
SN=<ccccc> No=<dddd>h
Name=<eee...e>)
[Classification] ERROR
[Explanation] It indicates that trouble (media error) occurred in the logical disk (number: dddd,
name: eee...e) of disk array (name: aaaaa).
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] Check the status of the logical disk with the trouble and perform the appropriate
maintenance.
Chapter 2 Message List
107
iSM07123: State of LD has become fault(media
error). (<aaa...a> productID=<bbb...b>
SN=<ccc...c> No=<dddd>h
Name=<eee...e> [PDN=<ff>h-<gg>h]))
[_ALERT_]
[Classification] ERROR
[Explanation] It indicates that trouble (media error) occurred in the logical disk (number: dddd,
name: eee...e) of disk array (name: aaa...a).
For Windows, this message is target of ESMPRO Manager Report.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2100 Disk Array etc.)
ccc...c : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
ff-gg : Corresponding physical disk number (only if physical disk fault
is the cause)
[Measures] Check the status of the logical disk with the trouble and perform the appropriate
maintenance.
Chapter 2 Message List
108
iSM07124: State of LD has become attn(reduce).
(<aaa...a> productID=<bbbbb>
SN=<ccccc> No=<dddd>h
Name=<eee...e>)
[Classification] ERROR
[Explanation] It indicates that the logical disk (number: dddd, name: eee...e) of disk array
(name: aaa...a) has become a reduced state*.
* RAID composition which lost redundancy by PD trouble.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] Check the status of the logical disk with the trouble and perform the appropriate
maintenance.
iSM07125: State of LD has become
attn(rebuilding). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dddd>h Name=<eee...e>)
[Classification] NOTICE
[Explanation] It indicates that the logical disk (number: dddd, name: eee...e) of disk array
(name: aaa...a) is rebuilding data.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] In relation to the measures for the logical disk caused by state transition, refer to
other applicable messages.
Chapter 2 Message List
109
iSM07126: State of LD has become
attn(preventive copy). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dddd>h Name=<eee...e>)
[Classification] NOTICE
[Explanation] It indicates that data in the logical disk (number: dddd, name: eee...e) of disk
array (name: aaa...a) has been copied into spare disk.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] Unnecessary
iSM07127: State of LD has become attn(copy
back). (<aaa...a> productID=<bbbbb>
SN=<ccccc> No=<dddd>h
Name=<eee...e>)
[Classification] NOTICE
[Explanation] It indicates that data in the logical disk (number: dddd, name: eee...e) of disk
array (name: aaa...a) has been restored from spare disk.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] Unnecessary
Chapter 2 Message List
110
iSM07128: State of LD has become
attn(unformatted). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dddd>h Name=<eee...e>)
[Classification] NOTICE
[Explanation] It indicates that the logical disk (number: dddd, name: eee...e) of disk array
(name: aaa...a) has been unformatted logically.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] In relation to the measures for resources caused by state transition, refer to other
applicable messages.
iSM07129: State of LD has become
attn(formatting). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dddd>h Name=<eee...e>)
[Classification] NOTICE
[Explanation] It indicates that the logical disk (number: dddd, name: eee...e) of disk array
(name: aaa...a) is being formatted logically.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] Unnecessary. However, this logical disk cannot be used until logical formatting
is completed.
Chapter 2 Message List
111
iSM07130: State of LD has become
attn(format-fail). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dddd>h Name=<eee...e>)
[Classification] NOTICE
[Explanation] It indicates that the logical disk (number: dddd, name: eee...e) of disk array
(name: aaa...a) failed in formatting logically.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] Check the status of the resource with the trouble and perform the appropriate
maintenance.
iSM07131: State of LD has become
attn(expanding). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dddd>h Name=<eee...e>)
[Classification] NOTICE
[Explanation] It indicates that the logical disk (number: dddd, name: eee...e) of disk array
(name: aaa...a) is expanding the logic.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] Unnecessary
Chapter 2 Message List
112
iSM07132: State of LD has become
attn(expand-fail). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dddd>h Name=<eee...e>)
[Classification] NOTICE
[Explanation] It indicates that the logical disk (number: dddd, name: eee...e) of disk array
(name: aaa...a) failed in logical expansion.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] Check the status of the resource with the trouble and perform the appropriate
maintenance.
iSM07133: State of LD has become
ready(formatting). (<aaa...a>
productID=<bbb...b> SN=<ccc...c>
No=<dddd>h Name=<eee...e>)
[Classification] INFO
[Explanation] It indicates the logical disk (number: dddd, name: eee...e) of a disk array (name:
aaa...a) is being formatted logically.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2800 Disk Array etc.)
ccc...c : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] Unnecessary. This logical disk can be used, but its I/O response may delay
until logical formatting is completed.
Chapter 2 Message List
113
iSM07141: State of RANK has become ready.
(<aaa...a> productID=<bbbbb>
SN=<ccccc> No=<dd>h-<ee>h )
[Classification] INFO
[Explanation] It indicates that the RANK (number: dd-ee) of disk array (name: aaa...a) has
become ready.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dd-ee : RANK number
[Measures] Unnecessary
iSM07142: State of RANK has become fault.
(<aaa...a> productID=<bbbbb>
SN=<ccccc> No=<dd>h-<ee>h )
[_ALERT_]
[Classification] ERROR
[Explanation] It indicates that a trouble occurred in the RANK (number: dd-ee) of disk array
(name: aaa...a).
For Windows, this message is target of ESMPRO Manager Report.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dd-ee : RANK number
[Measures] Check the status of the RANK with the trouble and perform the appropriate
maintenance.
Chapter 2 Message List
114
iSM07143: State of RANK has become
attn(reduce). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dd>h-<ee>h )
[Classification] ERROR
[Explanation] It indicates that the RANK (number: dd-ee) of disk array (name: aaa...a) has
become in reduced state.
* RAID composition which lost redundancy by PD trouble.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dd-ee : RANK number
[Measures] Check the status of the RANK with the trouble and perform the appropriate
maintenance.
iSM07144: State of RANK has become
attn(rebuilding). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dd>h-<ee>h )
[Classification] NOTICE
[Explanation] It indicates that the RANK (number: dd-ee) of disk array (name: aaa...a) is
rebuilding data.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dd-ee : RANK number
[Measures] In relation to the measures for the RANK caused by state transition, refer to other
applicable messages.
Chapter 2 Message List
115
iSM07145: State of RANK has become
attn(preventive copy). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dd>h-<ee>h )
[Classification] NOTICE
[Explanation] It indicates that data in the RANK (number: dd-ee) of disk array (name: aaa...a)
has been copied into spare disk.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dd-ee : RANK number
[Measures] Unnecessary
iSM07146: State of RANK has become attn(copy
back). (<aaa...a> productID=<bbbbb>
SN=<ccccc> No=<dd>h-<ee>h )
[Classification] NOTICE
[Explanation] It indicates that data in the RANK (number: dd-ee) of disk array (name: aaa...a)
has been restored from spare disk.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dd-ee : RANK number
[Measures] Unnecessary
Chapter 2 Message List
116
iSM07147: State of RANK has become
attn(expanding). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dd>h-<ee>h )
[Classification] NOTICE
[Explanation] It indicates that the rank (number: dd-ee) of disk array (name: aaa...a) is
expanding the logic.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dd-ee : RANK number
[Measures] Unnecessary
iSM07148: State of RANK has become
attn(expand-fail). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dd>h-<ee>h )
[Classification] NOTICE
[Explanation] It indicates that the rank (number: dd-ee) of disk array (name: aaa...a) failed in
logical expansion.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dd-ee : RANK number
[Measures] Check the status of the resource with the trouble and perform the appropriate
maintenance.
Chapter 2 Message List
117
iSM07151: State of PD(<aa>h) has become ready.
(<bbb...b> productID=<ccc...c>
SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>)
[Classification] INFO
[Explanation] It indicates that the physical disk (number: ee-ff) of disk array (name: bbb...b)
has become ready.
aa : Internal number indicating physical disk type
bbb...b : Disk array name
ccc...c : Product ID of disk array (S2800 Disk Array etc.)
ddd...d : Serial number of disk array
ee-ff : Physical disk number
ggg...g : Information of RANK or pool where the physical disk belongs
- PoolNo=<xxxx>h PoolName=<yyy...y>
Indicates pool information. (for the disk arrays with pool)
xxxx : Pool number
yyy...y : Pool name
- RankNo=<xx>h-<yy>h
Indicates RANK information. (for other than the disk arrays
with pool)
xx-yy : RANK number
[Measures] Unnecessary
Chapter 2 Message List
118
iSM07152: State of PD(<aa>h) has become fault.
(<bbb...b> productID=<ccc...c>
SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>) [UC=<hhh...h> FC=<ii>]
[_ALERT_]
[Classification] ERROR
[Explanation] It indicates that a trouble occurred in the physical disk (number: ee-ff) of disk
array (name: bbb...b).
For Windows, this message is target of ESMPRO Manager Report, and also to
be target of ALIVE/Express Report via ESMPRO.
aa : Internal number indicating physical disk type
bbb...b : Disk array name
ccc...c : Product ID of disk array (S2800 Disk Array etc.)
ddd...d : Serial number of disk array
ee-ff : Physical disk number
ggg...g : Information of RANK or pool where the physical disk belongs
- PoolNo=<xxxx>h PoolName=<yyy...y>
Indicates pool information. (for the disk arrays with pool)
xxxx : Pool number
yyy...y : Pool name
- RankNo=<xx>h-<yy>h
Indicates RANK information. (for other than the disk arrays
with pool)
xx-yy : RANK number
hhh...h/ii : Maintenance information
[Measures] Check the status of the resource with the trouble and perform the appropriate
maintenance.
Chapter 2 Message List
119
iSM07154: State of PD(<aa>h) has become
attn(rebuilding).
(<bbb...b> productID=<ccc...c>
SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>) [UC=<hhh...h> FC=<ii>]
[_ALERT_]
[Classification] NOTICE
[Explanation] It indicates that the physical disk (number: ee-ff) of disk array (name: bbb...b) is
rebuilding data.
For Windows, this message is target of ESMPRO Manager Report, and also to
be target of ALIVE/Express Report via ESMPRO.
aa : Internal number indicating physical disk type
bbb...b : Disk array name
ccc...c : Product ID of disk array (S2800 Disk Array etc.)
ddd...d : Serial number of disk array
ee-ff : Physical disk number
ggg...g : Information of RANK or pool where the physical disk belongs
- PoolNo=<xxxx>h PoolName=<yyy...y>
Indicates pool information. (for the disk arrays with pool)
xxxx : Pool number
yyy...y : Pool name
- RankNo=<xx>h-<yy>h
Indicates RANK information. (for other than the disk arrays
with pool)
xx-yy : RANK number
hhh...h/ii : Maintenance information
[Measures] Unnecessary
Chapter 2 Message List
120
iSM07155: State of PD(<aa>h) has become
attn(powering up).
(<bbb...b> productID=<ccc...c>
SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>)
[Classification] NOTICE
[Explanation] It indicates that the physical disk (number: ee-ff) of disk array (name: bbb...b) is
activated.
aa : Internal number indicating physical disk type
bbb...b : Disk array name
ccc...c : Product ID of disk array (S2800 Disk Array etc.)
ddd...d : Serial number of disk array
ee-ff : Physical disk number
ggg...g : Information of RANK or pool where the physical disk belongs
- PoolNo=<xxxx>h PoolName=<yyy...y>
Indicates pool information. (for the disk arrays with pool)
xxxx : Pool number
yyy...y : Pool name
- RankNo=<xx>h-<yy>h
Indicates RANK information. (for other than the disk arrays
with pool)
xx-yy : RANK number
[Measures] Unnecessary (It usually becomes ready within a few seconds. If the status does
not become ready, perform the appropriate maintenance because some trouble
may occur).
Chapter 2 Message List
121
iSM07156: State of PD(<aa>h) has become
attn(formatting).
(<bbb...b> productID=<ccc...c>
SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>)
[Classification] NOTICE
[Explanation] It indicates that the physical disk (number: ee-ff) of disk array (name: bbb...b) is
being formatted.
aa : Internal number indicating physical disk type
bbb...b : Disk array name
ccc...c : Product ID of disk array (S2800 Disk Array etc.)
ddd...d : Serial number of disk array
ee-ff : Physical disk number
ggg...g : Information of RANK or pool where the physical disk belongs
- PoolNo=<xxxx>h PoolName=<yyy...y>
Indicates pool information. (for the disk arrays with pool)
xxxx : Pool number
yyy...y : Pool name
- RankNo=<xx>h-<yy>h
Indicates RANK information. (for other than the disk arrays
with pool)
xx-yy : RANK number
[Measures] Unnecessary
Chapter 2 Message List
122
iSM07158: State of PD(<aa>h) has become
offline. (<bbb...b>
productID=<ccc...c> SN=<ddd...d>
No=<ee>h-<ff>h <ggg...g>)
[Classification] ERROR
[Explanation] It indicates that the physical disk (number: ee-ff) of disk array (name: bbb...b)
has been in the off line status.
aa : Internal number indicating physical disk type
bbb...b : Disk array name
ccc...c : Product ID of disk array (S2800 Disk Array etc.)
ddd...d : Serial number of disk array
ee-ff : Physical disk number
ggg...g : Information of RANK or pool where the physical disk belongs
- PoolNo=<xxxx>h PoolName=<yyy...y>
Indicates pool information. (for the disk arrays with pool)
xxxx : Pool number
yyy...y : Pool name
- RankNo=<xx>h-<yy>h
Indicates RANK information. (for other than the disk arrays
with pool)
xx-yy : RANK number
[Measures] Check the physical disk in which the state transition occurred, and perform the
appropriate maintenance.
Chapter 2 Message List
123
iSM07159: State of PD(<aa>h) has become ready.
(<bbb...b> productID=<ccc...c>
SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>) [UC=<hhh...h> FC=<ii>]
[_ALERT_]
[Classification] INFO
[Explanation] It indicates that the physical disk (number: ee-ff) of disk array (name: bbb...b)
has rebuilt data and its status has changed to “ready”.
For Windows, this message is target of ESMPRO Manager Report, and also to
be target of ALIVE/Express Report via ESMPRO.
aa : Internal number indicating physical disk type
bbb...b : Disk array name
ccc...c : Product ID of disk array (S2800 Disk Array etc.)
ddd...d : Serial number of disk array
ee-ff : Physical disk number
ggg...g : Information of RANK or pool where the physical disk belongs
- PoolNo=<xxxx>h PoolName=<yyy...y>
Indicates pool information. (for the disk arrays with pool)
xxxx : Pool number
yyy...y : Pool name
- RankNo=<xx>h-<yy>h
Indicates RANK information. (for other than the disk arrays
with pool)
xx-yy : RANK number
hhh...h/ii : Maintenance information
[Measures] Unnecessary
Chapter 2 Message List
124
iSM07161: State of <aaaaa>(<bb>h[-<cc>h]) has
become ready. (<ddd...d>
productID=<eeeee> SN=<fffff>
No=<gg>h)
[Classification] INFO
[Explanation] It indicates that the component* (abbreviated name: aaaaa, number: gg) of disk
array (name: ddd...d) has become ready.
aaaaa : Abbreviated name of component
bb-cc : Internal number indicating component type
ddd...d : Disk array name
eeeee : Product ID of disk array (S2100 Disk Array etc.)
fffff : Serial number of disk array
gg : Component number
*except for logical disk/physical disk
[Measures] Unnecessary
Chapter 2 Message List
125
iSM07162: State of <aaaaa>(<bb>h[-<cc>h]) has
become fault. (<ddd...d>
productID=<eeeee> SN=<fffff>
No=<gg>h) [UC=<hhhhhhhhhh>
FC=<ii>][_ALERT_]
[Classification] ERROR
[Explanation] It indicates that trouble occurred in the component* (abbreviated name: aaaaa,
number: gg) of disk array (name: ddd...d).
For Windows, this message is target of ESMPRO Manager Report, and also to
be target of ALIVE/Express Report via ESMPRO.
aaaaa : Abbreviated name of component
bb-cc : Internal number indicating component type
ddd...d : Disk array name
eeeee : Product ID of disk array (S2100 Disk Array etc.)
fffff : Serial number of disk array
gg : Component number
hhhhhhhhhh/ii : Maintenance information
*except for logical disk/physical disk
[Measures] Check the status of the resource with the trouble and perform the appropriate
maintenance.
Chapter 2 Message List
126
iSM07163: State of <aaaaa>(<bb>h[-<cc>h]) has
become offline. (<ddd...d>
productID=<eeeee> SN=<fffff>
No=<gg>h)
[Classification] ERROR
[Explanation] It indicates that the component* (abbreviated name: aaaaa, number: gg) of disk
array (name: ddd...d) has become removed (or not existed).
aaaaa : Abbreviated name of component
bb-cc : Internal number indicating component type
ddd...d : Disk array name
eeeee : Product ID of disk array (S2100 Disk Array etc.)
fffff : Serial number of disk array
gg : Component number
*except for logical disk/physical disk
[Measures] Check the resource in which the state transition occurred, and perform the
appropriate maintenance.
iSM07164: State of HD(<aa>h) has become
attn(nolicense). (<bbb...b>
productID=<ccccc> SN=<ddddd>
No=<ee>h )
[Classification] NOTICE
[Explanation] The program product BaseProduct has not been installed, and the host director
(number: ee) of the disk array (name: bbb...b) is not available.
aa : Internal number indicating the type of the component
bbb...b : Disk array name
ccccc : Product ID of disk array (S2100 Disk Array etc.)
ddddd : Serial number of the disk array
ee : Component number
*except for logical disk/physical disk
[Measures] Install the program product BaseProduct for the host director.
Chapter 2 Message List
127
iSM07165: State of CHE(<aa>h[-<bb>h]) has
become attn(rebuilding). (<ccc...c>
productID=<ddd...d> SN=<eee...e>
No=<ff>h )
[Classification] NOTICE
[Explanation] It indicates that cache module (number: ff) of a disk array (name: ccc...c) is
rebuilding data.
aa-bb : Internal number indicating component type
ccc...c : Disk array name
ddd...d : Product ID of disk array (S2800 Disk Array etc.)
eee...e : Serial number of disk array
ff : Component number
[Measures] Unnecessary
iSM07166: State of DAC_BBU(<aa>h[-<bb>h])
has become attn(charge). (<ccc...c>
productID=<ddd...d> SN=<eee...e>
No=<ff>h )
[Classification] NOTICE
[Explanation] It indicates that the battery (number: ff) of a disk array (name: ccc...c) is
charging.
aa-bb : Internal number indicating component type
ccc...c : Disk array name
ddd...d : Product ID of disk array (S2800 Disk Array etc.)
eee...e : Serial number of disk array
ff : Component number
[Measures] Unnecessary
Chapter 2 Message List
128
iSM07171: State of LD has become ready.
(<aaa...a> productID=<bbbbb>
SN=<ccccc> No=<dddd>h
Name=<eee...e>)
[Classification] INFO
[Explanation] It indicates that the logical disk (number: dddd, name: eee...e) of disk array
(name: aaa...a) has become ready.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] Unnecessary
iSM07172: State of LD has become fault.
(<aaa...a> productID=<bbbbb>
SN=<ccccc> No=<dddd>h
Name=<eee...e>)
[Classification] ERROR
[Explanation] It indicates that trouble occurred in the logical disk (number: dddd, name: eee...e)
of disk array (name: aaa...a).
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] Check the status of the logical disk with the trouble and perform the appropriate
maintenance.
Chapter 2 Message List
129
iSM07173: State of LD has become fault(media
error). (<aaa...a> productID=<bbb...b>
SN=<ccc...c> No=<dddd>h
Name=<eee...e> [PDN=<ff>h-<gg>h])
[UC=<hhh...h> FC=<ii>][_ALERT_]
[Classification] ERROR
[Explanation] It indicates that trouble (media error) occurred in the logical disk (number: dddd,
name: eee...e) of disk array (name: aaa...a).
For Windows, this message is target of ESMPRO Manager Report, and also to
be target of ALIVE/Express Report via ESMPRO.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2100 Disk Array etc.)
ccc...c : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
ff-gg : Corresponding physical disk number (only if physical disk fault
is the cause)
hhh...h/ii : Maintenance information
[Measures] Check the status of the logical disk with the trouble and perform the appropriate
maintenance.
Chapter 2 Message List
130
iSM07174: State of LD has become attn(reduce).
(<aaa...a> productID=<bbbbb>
SN=<ccccc> No=<dddd>h
Name=<eee...e>)
[Classification] ERROR
[Explanation] It indicates that the logical disk (number: dddd, name: eee...e) of disk array
(name: aaa...a) has become a reduced state*.
* RAID composition which lost redundancy by PD trouble.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] Check the status of the logical disk with the trouble and perform the appropriate
maintenance.
iSM07175: State of LD has become
attn(rebuilding). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dddd>h Name=<eee...e>)
[Classification] NOTICE
[Explanation] It indicates that the logical disk (number: dddd, name: eee...e) of disk array
(name: aaa...a) is rebuilding data.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] In relation to the measures for the logical disk caused by state transition, refer to
other applicable messages.
Chapter 2 Message List
131
iSM07176: State of LD has become
attn(preventive copy). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dddd>h Name=<eee...e>)
[Classification] NOTICE
[Explanation] It indicates that data in the logical disk (number: dddd, name: eee...e) of disk
array (name: aaa...a) has been copied into spare disk.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] Unnecessary
iSM07177: State of LD has become attn(copy
back). (<aaa...a> productID=<bbbbb>
SN=<ccccc> No=<dddd>h
Name=<eee...e>)
[Classification] NOTICE
[Explanation] It indicates that data in the logical disk (number: dddd, name: eee...e) of disk
array (name: aaa...a) has been restored from spare disk.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] Unnecessary
Chapter 2 Message List
132
iSM07178: State of LD has become
attn(unformatted). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dddd>h Name=<eee...e>)
[Classification] NOTICE
[Explanation] It indicates that the logical disk (number: dddd, name: eee...e) of disk array
(name: aaa...a) has been unformatted logically.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] In relation to the measures for resources caused by state transition, refer to other
applicable messages.
iSM07179: State of LD has become
attn(formatting). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dddd>h Name=<eee...e>)
[Classification] NOTICE
[Explanation] It indicates that the logical disk (number: dddd, name: eee...e) of disk array
(name: aaa...a) is being formatted logically.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] Unnecessary. However, this logical disk cannot be used until logical formatting
is completed.
Chapter 2 Message List
133
iSM07180: State of LD has become
attn(format-fail). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dddd>h Name=<eee...e>)
[Classification] NOTICE
[Explanation] It indicates that the logical disk (number: dddd, name: eee...e) of disk array
(name: aaa...a) failed in formatting logically.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] Check the status of the resource with the trouble and perform the appropriate
maintenance.
iSM07181: State of LD has become
attn(expanding). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dddd>h Name=<eee...e>)
[Classification] NOTICE
[Explanation] It indicates that the logical disk (number: dddd, name: eee...e) of disk array
(name: aaa...a) is expanding the logic.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] Unnecessary
Chapter 2 Message List
134
iSM07182: State of LD has become
attn(expand-fail). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dddd>h Name=<eee...e>)
[Classification] NOTICE
[Explanation] It indicates that the logical disk (number: dddd, name: eee...e) of disk array
(name: aaa...a) failed in logical expansion.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] Check the status of the resource with the trouble and perform the appropriate
maintenance.
iSM07183: State of LD has become
ready(formatting). (<aaa...a>
productID=<bbb...b> SN=<ccc...c>
No=<dddd>h Name=<eee...e>)
[Classification] INFO
[Explanation] It indicates that the logical disk (number: dddd, name: eee...e) of a disk array
(name: aaa...a) is being formatted logically.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2800 Disk Array etc.)
ccc...c : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] Unnecessary. This logical disk can be used, but its I/O response may delay
until logical formatting is completed.
Chapter 2 Message List
135
iSM07191: State of RANK has become ready.
(<aaa...a> productID=<bbbbb>
SN=<ccccc> No=<dd>h-<ee>h)
[Classification] INFO
[Explanation] It indicates that the RANK (number: dd-ee) of disk array (name: aaa...a) has
become ready.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dd-ee : RANK number
[Measures] Unnecessary
iSM07192: State of RANK has become fault.
(<aaa...a> productID=<bbbbb>
SN=<ccccc> No=<dd>h-<ee>h)
[UC=<ffffffffff> FC=<gg>][_ALERT_]
[Classification] ERROR
[Explanation] It indicates that a trouble occurred in the RANK (number: dd-ee) of disk array
(name: aaa...a).
For Windows, this message is target of ESMPRO Manager Report, and also to
be target of ALIVE/Express Report via ESMPRO.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dd-ee : RANK number
ffffffffff/gg : Maintenance information
[Measures] Check the status of the RANK with the trouble and perform the appropriate
maintenance.
Chapter 2 Message List
136
iSM07193: State of RANK has become
attn(reduce). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dd>h-<ee>h)
[Classification] ERROR
[Explanation] It indicates that the RANK (number: dd-ee) of disk array (name: aaa...a) has
become in reduced state.
* RAID composition which lost redundancy by PD trouble.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dd-ee : RANK number
[Measures] Check the status of the RANK with the trouble and perform the appropriate
maintenance.
iSM07194: State of RANK has become
attn(rebuilding). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dd>h-<ee>h)
[Classification] NOTICE
[Explanation] It indicates that the RANK (number: dd-ee) of disk array (name: aaa...a) is
rebuilding data.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dd-ee : RANK number
[Measures] In relation to the measures for the RANK caused by state transition, refer to other
applicable messages.
Chapter 2 Message List
137
iSM07195: State of RANK has become attn
(preventive copy). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dd>h-<ee>h)
[Classification] NOTICE
[Explanation] It indicates that data in the RANK (number: dd-ee) of disk array (name: aaa...a)
has been copied into spare disk.
This message is output on UNIX system.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dd-ee : RANK number
[Measures] Unnecessary
iSM07196: State of RANK has become attn(copy
back). (<aaa...a> productID=<bbbbb>
SN=<ccccc> No=<dd>h-<ee>h)
[Classification] NOTICE
[Explanation] It indicates that data in the RANK (number: dd-ee) of disk array (name: aaa...a)
has been restored from spare disk.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dd-ee : RANK number
[Measures] Unnecessary
Chapter 2 Message List
138
iSM07197: State of RANK has become
attn(expanding). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dd>h-<ee>h)
[Classification] NOTICE
[Explanation] It indicates that the rank (number: dd-ee) of disk array (name: aaa...a) is
expanding the logic.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dd-ee : RANK number
[Measures] Unnecessary
iSM07198: State of RANK has become
attn(expand-fail). (<aaa...a>
productID=<bbbbb> SN=<ccccc>
No=<dd>h-<ee>h)
[Classification] NOTICE
[Explanation] It indicates that the rank (number: dd-ee) of disk array (name: aaa...a) failed in
logical expansion.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dd-ee : RANK number
[Measures] Check the status of the resource with the trouble and perform the appropriate
maintenance.
Chapter 2 Message List
139
iSM07201: Disk Array ,named “<aaa...a>”, has
renamed to “<bbb...b>”.
(SN=<ccccc>)
[Classification] INFO
[Explanation] It indicates that the name of disk array (name: aaa...a, serial number: ccccc) has
been changed to bbb...b.
aaa...a : Disk array name
bbb...b : New disk array name
ccccc : Serial number
[Measures] Unnecessary
iSM07202: PORT,named “<aaa...a>”, has
renamed to “<bbb...b>”. (<ccc...c>
No=<dd>h-<ee>h)
[Classification] INFO
[Explanation] It indicates that the port (number: dd-ee) name of disk array (name: ccc...c) has
been changed from aaa...a to bbb...b.
aaa...a : Old port name
bbb...b : New port name
ccc...c : Disk array name
dd-ee : Port number
[Measures] Unnecessary
Chapter 2 Message List
140
iSM07203: LD ,named “<aaa...a>”, has renamed
to “<bbb...b>”.
(<ccc...c>No=<dddd>h)
[Classification] INFO
[Explanation] It indicates that the logical disk (number: dddd) name of disk array (name:
ccc...c)has been changed from aaa...a to bbb...b.
aaa...a : Old Logical disk name
bbb...b : New Logical disk name
ccc...c : Disk array name
dddd : Logical disk number
[Measures] Unnecessary
iSM07204: Name setting has executed with SG
file. (<aaa...a>)
[Classification] INFO
[Explanation] It indicates that the name setting (of all of disk array, LD and Port, or some) of
disk array (name: aaa...a) has been executed by the definition file (SG file).
aaa...a : Disk array name
[Measures] Unnecessary
iSM07205: LD has configured. (<aaa...a>)
[Classification] NOTICE
[Explanation] It shows that the logical disk configuration of disk array (name: aaa...a) was
changed.
aaa...a : Disk array name
[Measures] Unnecessary
Chapter 2 Message List
141
iSM07206: CHE-Disk has configured.(<aaa...a>)
[Classification] NOTICE
[Explanation] It indicates that the cache disk configuration of disk array (name: aaa...a) has
been changed.
aaa...a : Disk array name
[Measures] Unnecessary
iSM07207: Attribute of PD has changed from
<aaaaa> to <bbbbb>. (<ccc...c>
No=<dd>h-<ee>h)
[Classification] NOTICE
[Explanation] It indicates that partition (data, spare) in the physical disk (number: dd-ee) of
disk array (name: ccc...c) has been changed.
aaaaa : Old partition
bbbbb : New partition
ccc...c : Disk array name
dd-ee : Physical disk number
[Measures] Unnecessary
iSM07208: ACCESS_CONTROL has
configured.(<aaa...a>)
[Classification] NOTICE
[Explanation] It indicates that Access Control of disk array (name: aaa...a) has been set.
aaa...a : Disk array name
[Measures] Unnecessary
Chapter 2 Message List
142
iSM07211: Renaming Disk Array,named
“<aaa...a>”,is failed. (SN=<bbbbb>)
[Classification] INFO
[Explanation] It indicates that change of disk array names (name: aaa...a, serial number: bbbbb)
failed.
aaa...a : Disk array name
bbbbb : Serial number
[Measures] Check result indicated on client screen (dialog) and remove cause of the failure.
Then change the names again.
iSM07212: Renaming PORT of “<aaa...a>” is
failed. (No=<bb>h-<cc>h)
[Classification] INFO
[Explanation] It indicates that change of port name (number: bb-cc) of disk array (name:
aaa...a) failed.
aaa...a : Disk array name
bb-cc : Port number
[Measures] Check result indicated on client screen (dialog) and remove cause of the failure.
Then change the names again.
iSM07213: Renaming LD of “<aaa...a>” is failed.
(No=<bbbb>h)
[Classification] INFO
[Explanation] It indicates that change of logical disk (number: bbbb) of disk array (name:
aaa...a) failed.
aaa...a : Disk array name
bbbb : Logical disk number
[Measures] Check result indicated on client screen (dialog) and remove cause of the failure.
Then change the names again.
Chapter 2 Message List
143
iSM07220: SVP information was updated.
(<aaa...a> productID=<bbbbb>
SN=<ccccc> No=<dd>h)
[Classification] INFO
[Explanation] It indicates that service processor information (component number: dd) of disk
array (name: aaa...a) has been changed.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
dd : Component number of service processor.
[Measures] Unnecessary
iSM07221: Product information was changed.
(<aaa...a> productID=<bbbbb>
SN=<ccccc>)
[Classification] INFO
[Explanation] It indicates that product information of disk array (name: aaa...a) has been
changed.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
[Measures] Unnecessary
Chapter 2 Message List
144
iSM07251: Disk Array name “<aaa...a>” exists in
others. (productID=<bbbbb>
SN=<ccccc>)
[Classification] WARNING
[Explanation] It indicates that the disk array name (aaa...a) (product ID: bbbbb, serial number:
ccccc) is duplicated.
aaa...a : Disk array name
bbbbb : Product ID of disk array (S2100 Disk Array etc.)
ccccc : Serial number of disk array
[Measures] Check the disk arrays with the same name, and correct the name.
iSM07252: PORT name “<aaa...a>” exists in
others. (<bbb...b> No=<cc>h-<dd>h)
[Classification] WARNING
[Explanation] It indicates that the name (aaa...a) of port (number: cc-dd) of the disk array
(name: bbb...b) is duplicated.
aaa...a : Port name
bbb...b : Disk array name
cc-dd : Port number
[Measures] Check the ports with the same name, and correct the name.
iSM07253: LD name “<aaa...a>” exists in others.
(<bbb...b> No=<cccc>h)
[Classification] WARNING
[Explanation] It indicates that the name (aaa...a) of logical disk (number: ccccc) in the disk
array (name: bbb...b) is duplicated.
aaa...a : Logical disk name
bbb...b : Disk array name
cccc : Logical disk number
[Measures] Check the logical disks with the same name, and correct the name.
Chapter 2 Message List
145
iSM07301: LD_SET,named “<aaa...a>” was
added. (<bbb...b>)
[Classification] INFO
[Explanation] It indicates that LD_SET (name: aaa...a) is added to disk array (name: bbb...b).
aaa...a : LD_SET name
bbb...b : Disk array name
[Measures] Unnecessary
iSM07302: LD_SET,named “<aaa...a>” was
deleted. (<bbb...b>)
[Classification] INFO
[Explanation] It indicates that LD_SET (name: aaa...a) is deleted from disk array (name:
bbb...b).
aaa...a : LD_SET name
bbb...b : Disk array name
[Measures] Unnecessary
iSM07303: PATH, “<aaa...a>” was added to
LD_SET.(<bbb...b> LD_SET=<ccc...c>)
[Classification] INFO
[Explanation] It indicates that the path (aaa...a) is added to LD_SET (name: ccc...c) of disk
array (name: bbb...b).
aaa...a : Path
aaaa-aaaa-aaaa-aaaa : WWPN
aah-aah : Port number
bbb...b : Disk array name
ccc...c : LD_SET name
[Measures] Unnecessary
Chapter 2 Message List
146
iSM07304: PATH, “<aaa...a>” was deleted from
LD_SET. (<bbb...b> LD_SET=<ccc...c>)
[Classification] INFO
[Explanation] It indicates that the path (aaa...a) is deleted from LD_SET (name: ccc...c) of disk
array (name: bbb...b).
aaa...a : Path
aaaa-aaaa-aaaa-aaaa : WWPN
aah-aah : Port number
bbb...b : Disk array name
ccc...c : LD_SET name
[Measures] Unnecessary
iSM07305: Some of LDs were assigned to
LD_SET. (<aaa...a> LD_SET=<bbb...b>
PATH=<ccc...c>)
[Classification] INFO
[Explanation] It indicates that LDs are assigned to LD_SET (name: bbb...b) of disk array
(name: aaa...a) and the path (cccc-cccc-cccc-cccc).
aaa...a : Disk array name
bbb...b : LD_SET name
ccc...c : Path
cccc-cccc-cccc-cccc : WWPN
cch-cch : Port number
[Measures] Unnecessary
iSM07306: Some of LDs were assigned to
LD_SET. (<aaa...a> LD_SET=<bbb...b>)
[Classification] INFO
[Explanation] It indicates that LDs are assigned to LD_SET (name: bbb...b) of disk array
(name: aaa...a).
aaa...a : Disk array name
bbb...b : LD_SET name
[Measures] Unnecessary
Chapter 2 Message List
147
iSM07307: PATH, “<aaa...a>” was changed for
“<bbb...b>”. (<ccc...c>
LD_SET=<ddd...d>)
[Classification] INFO
[Explanation] It indicates that the path aaa...a to LD_SET (name: ddd...d) of disk array (name:
ccc...c) is changed to bbb...b.
aaa...a : Old path
aaaa-aaaa-aaaa-aaaa : WWPN
aah-aah : Port number
bbb...b : New path
bbbb-bbbb-bbbb-bbbb : WWPN
bbh-bbh : Port number
ccc...c : Disk array name
ddd...d : LD_SET name
[Measures] Unnecessary
iSM07308: LD,named “<aaa...a>”(<bbbb>h) was
added to LD_SET. (<ccc...c>
LD_SET=<ddd...d> PATH=<eee...e>)
[Classification] INFO
[Explanation] It indicates that the logical disk (name: aaa...a, number: bbbb) is added to
LD_SET (name: ddd...d) of disk array (name: ccc...c) and the logical disk is
accessible via the path (eee...e).
aaa...a : Logical disk name
bbbb : Logical disk number
ccc...c : Disk array name
ddd...d : LD_SET name
eee...e : Path
eeee-eeee-eeee-eeee : WWPN
eeh-eeh : Port number
[Measures] Unnecessary
Chapter 2 Message List
148
iSM07309: LD,named “<aaa...a>”(<bbbb>h) was
added to LD_SET. (<ccc...c>
LD_SET=<ddd...d>)
[Classification] INFO
[Explanation] It indicates that the logical disk (name: aaa...a, number: bbbb) is added to
LD_SET (name: ddd...d) of disk array (name: ccc...c).
aaa...a : Logical disk name
bbbb : Logical disk number
ccc...c : Disk array name
ddd...d : LD_SET name
[Measures] Unnecessary
iSM07310: LD,named “<aaa...a>”(<bbbb>h) was
deleted from LD_SET. (<ccc...c>
LD_SET=<ddd...d> PATH=<eee...e>)
[Classification] INFO
[Explanation] It indicates that the logical disk (name: aaa...a, number: bbbb) is added to
LD_SET (name: ddd...d) of disk array (name: ccc...c) and the logical disk is
inaccessible via the path (eee...e).
aaa...a : Logical disk name
bbbb : Logical disk number
ccc...c : Disk array name
ddd...d : LD_SET name
eee...e : Path
eeee-eeee-eeee-eeee : WWPN
eeh-eeh : Port number
[Measures] Unnecessary
Chapter 2 Message List
149
iSM07311: LD,named “<aaa...a>”(<bbbb>h) was
deleted from LD_SET. (<ccc...c>
LD_SET=<ddd...d>)
[Classification] INFO
[Explanation] It indicates that the logical disk (name: aaa...a, number: bbbb) is deleted from
LD_SET (name: ddd...d) of disk array (name: ccc...c).
aaa...a : Logical disk name
bbbb : Logical disk number
ccc...c : Disk array name
ddd...d : LD_SET name
[Measures] Unnecessary
iSM07312: ACCESS_CONTROL mode was
changed into <aaaa>. (<bbb...b>
No=<cc>h-<dd>h)
[Classification] INFO
[Explanation] It indicates that Access Control of port (number: cc-dd) of disk array (name:
bbb...b) is changed to aaaa mode.
aaaa : Access Control mode after changing (WWN/Port)
bbb...b : Disk array name
cc-dd : Port number
[Measures] Unnecessary
iSM07313: ACCESS_CONTROL function was
started. (<aaa...a>)
[Classification] INFO
[Explanation] It indicates that function of Access Control of disk array (name: aaa...a) is
started.
aaa...a : Disk array name
[Measures] Unnecessary
Chapter 2 Message List
150
iSM07314: ACCESS_CONTROL function was
stopped. (<aaa...a>)
[Classification] INFO
[Explanation] It indicates that access control function on disk array (name: aaa...a) has been
stopped.
aaa...a : Disk array name
[Measures] Unnecessary
iSM07315: LD_SET, named “<aaa...a>”, has
renamed to “<bbb...b>”. (<ccc...c>)
[Classification] INFO
[Explanation] It indicates that LD_SET name of disk array (name: ccc...c) has been changed
from aaa...a to bbb...b.
aaa...a : Old LD_SET name
bbb...b : New LD_SET name
ccc...c : Disk array name
[Measures] Unnecessary
iSM07316: Platform was re-set up. (<aaa...a>
LD_SET=<bbb...b>)
[Classification] INFO
[Explanation] It indicates that platform information for LD_SET (name: bbb...b) of disk array
(name: aaa...a) has been specified again.
aaa...a : Disk array name
bbb...b : LD_SET name
[Measures] Unnecessary
Chapter 2 Message List
151
iSM07331: Adding a LD_SET, named “<aaa...a>”
was failed. (<bbb...b>)
[Classification] INFO
[Explanation] It indicates that adding the LD_SET (name: aaa...a) to disk array (name: bbb...b)
failed.
aaa...a : LD_SET name
bbb...b : Disk array name
[Measures] Identify a cause of fault on the basis of previous and following messages, remove
the cause of fault, and then retry processing.
iSM07332: Deleting a LD_SET, named
“<aaa...a>” was failed. (<bbb...b>)
[Classification] INFO
[Explanation] It indicates that deleting the LD_SET (name: aaa...a) from disk array (name:
bbb...b) failed.
aaa...a : LD_SET name
bbb...b : Disk array name
[Measures] Identify a cause of fault on the basis of previous and following messages, remove
the cause of fault, and then retry processing.
iSM07333: Adding a PATH, named “<aaa...a>” to
LD_SET was failed. (<bbb...b>
LD_SET=<ccc...c>)
[Classification] INFO
[Explanation] It indicates that adding Path (aaa...a) to LD_SET (name: ccc...c) of disk array
(name: bbb...b) failed.
aaa...a : Path
aaaa-aaaa-aaaa-aaaa : WWPN
aah-aah : Port number
bbb...b : Disk array name
ccc...c : LD_SET name
[Measures] Identify a cause of fault on the basis of previous and following messages, remove
the cause of fault, and then retry processing.
Chapter 2 Message List
152
iSM07334: Deleting a PATH, named “<aaa...a>”
to LD_SET was failed. (<bbb...b>
LD_SET=<ccc...c>)
[Classification] INFO
[Explanation] It indicates that deleting Path (aaa...a) from LD_SET (name: ccc...c) of disk array
(name: bbb...b) failed.
aaa...a : Path
aaaa-aaaa-aaaa-aaaa : WWPN
aah-aah : Port number
bbb...b : Disk array name
ccc...c : LD_SET name
[Measures] Identify a cause of fault on the basis of previous and following messages, remove
the cause of fault, and then retry processing.
iSM07335: Assigning some of LDs, to LD_SET
was failed. (<aaa...a>
LD_SET=<bbb...b> PATH=<ccc...c>)
[Classification] INFO
[Explanation] It indicates that assigning Logical Disk to LD_SET (name: bbb...b) of disk array
(name: aaa...a), Path (ccc...c) failed.
aaa...a : Disk array name
bbb...b : LD_SET name
ccc...c : Path
cccc-cccc-cccc-cccc : WWPN
cch-cch : Port number
[Measures] Identify a cause of fault on the basis of previous and following messages, remove
the cause of fault, and then retry processing.
Chapter 2 Message List
153
iSM07336: Assigning some of LDs, to LD_SET
was failed. (<aaa...a>
LD_SET=<bbb...b>)
[Classification] INFO
[Explanation] It indicates that assigning Logical Disk to LD_SET (name: bbb...b) of disk array
(name: aaa...a) failed.
aaa...a : Disk array name
bbb...b : LD_SET name
[Measures] Identify a cause of fault on the basis of previous and following messages, remove
the cause of fault, and then retry processing.
iSM07337: Changing a PATH, from “<aaa...a>” to
“<bbb...b>” was failed. (<ccc...c>
LD_SET=<ddd...d>)
[Classification] INFO
[Explanation] It indicates that changing Path to LD_SET (name: ddd...d) of disk array (name:
ccc...c) from “aaa...a” to “bbb...b” failed.
aaa...a : Path before change
aaaa-aaaa-aaaa-aaaa : WWPN
aah-aah : Port number
bbb...b : Path after change
bbbb-bbbb-bbbb-bbbb : WWPN
bbh-bbh : Port number
ccc...c : Disk array name
ddd...d : LD_SET name
[Measures] Identify a cause of fault on the basis of previous and following messages, remove
the cause of fault, and then retry processing.
Chapter 2 Message List
154
iSM07338: Adding a LD, named “<aaa...a>”
(<bbbb>h), to LD_SET was failed.
(<ccc...c> LD_SET=<ddd...d>
PATH=<eee...e>)
[Classification] INFO
[Explanation] It indicates that adding Logical Disk (name: aaa...a, number: bbbb) to LD_SET
(name: ddd...d) of disk array (name: ccc...c) , Path (eee...e) failed.
aaa...a : Logical disk name
bbbb : Logical disk number
ccc...c : Disk array name
ddd...d : LD_SET name
eee...e : Path
eeee-eeee-eeee-eeee : WWPN
eeh-eeh : Port number
[Measures] Identify a cause of fault on the basis of previous and following messages, remove
the cause of fault, and then retry processing.
iSM07339: Adding a LD, named “<aaa...a>”
(<bbbb>h), to LD_SET was failed.
(<ccc...c> LD_SET=<ddd...d>)
[Classification] INFO
[Explanation] It indicates that adding Logical Disk (name: aaa...a, number: bbbb) to LD_SET
(name: ddd...d) of disk array (name: ccc...c) failed.
aaa...a : Logical disk name
bbbb : Logical disk number
ccc...c : Disk array name
ddd...d : LD_SET name
[Measures] Identify a cause of fault on the basis of previous and following messages, remove
the cause of fault, and then retry processing.
Chapter 2 Message List
155
iSM07340: Deleting a LD, named “<aaa...a>”
(<bbbb>h), from LD_SET was failed.
(<ccc...c> LD_SET=<ddd...d>
PATH=<eee...e>)
[Classification] INFO
[Explanation] It indicates that deleting Logical Disk (name: aaa...a) from LD_SET (name:
ddd...d) of disk array (name: ccc...c), Path (eee...e) was failed.
aaa...a : Logical disk name
bbbb : Logical disk number
ccc...c : Disk array name
ddd...d : LD_SET name
eee...e : Path
eeee-eeee-eeee-eeee : WWPN
eeh-eeh : Port number
[Measures] Identify a cause of fault on the basis of previous and following messages, remove
the cause of fault, and then retry processing.
iSM07341: Deleting a LD, named “<aaa...a>”
(<bbbb>h), from LD_SET was failed.
(<ccc...c> LD_SET=<ddd...d>)
[Classification] INFO
[Explanation] It indicates that deleting Logical Disk (name: aaa...a, number: bbbb) from
LD_SET (name: ddd...d) of disk array (name: ccc...c) failed.
aaa...a : Logical disk name
bbbb : Logical disk number
ccc...c : Disk array name
ddd...d : LD_SET name
[Measures] Identify a cause of fault on the basis of previous and following messages, remove
the cause of fault, and then retry processing.
Chapter 2 Message List
156
iSM07342: Changing ACCESS_CONTROL mode
was failed. (<aaa...a>
No=<bb>h-<cc>h)
[Classification] INFO
[Explanation] It indicates that changing Port (number: bb-cc) of disk array (name: aaa...a)
failed.
aaa...a : Disk array name
bb-cc : Port number
[Measures] Identify a cause of fault on the basis of previous and following messages, remove
the cause of fault, and then retry processing.
iSM07343: Starting ACCESS_CONTROL function
was failed. (<aaa...a>)
[Classification] INFO
[Explanation] It indicates that starting Access Control function of disk array (name: aaa...a)
failed.
aaa...a : Disk array name
[Measures] Identify a cause of fault on the basis of previous and following messages, remove
the cause of fault, and then retry processing.
iSM07344: Stopping ACCESS_CONTROL
function was failed. (<aaa...a>)
[Classification] INFO
[Explanation] It indicates that stopping Access Control function of disk array (name: aaa...a)
failed.
aaa...a : Disk array name
[Measures] Identify a cause of fault on the basis of previous and following messages, remove
the cause of fault, and then retry processing.
Chapter 2 Message List
157
iSM07345: Renaming LD_SET, named
“<aaa...a>” was failed. (<bbb...b>)
[Classification] INFO
[Explanation] It indicates that renaming the LD_SET (name: aaa...a) to disk array (name:
bbb...b) failed.
aaa...a : LD_SET name
bbb...b : Disk array name
[Measures] Identify a cause of fault on the basis of previous and following messages, remove
the cause of fault, and then retry processing.
iSM07346: Re-setup of Platform was failed.
(<aaa...a> LD_SET=<bbb...b>)
[Classification] INFO
[Explanation] It indicates that re-setup of the platform information set to the LD_SET (name:
bbb...b) of disk array (name: aaa...a) failed.
aaa...a : Disk array name
bbb...b : LD_SET name
[Measures] Identify a cause of fault on the basis of previous and following messages, remove
the cause of fault, and then retry processing.
Chapter 2 Message List
158
iSM07402: State of PD(<aa>h) has become
info(inactive). (<bbb...b>
productID=<ccc...c> SN=<ddd...d>
No=<ee>h-<ff>h <ggg...g>)[_ALERT_]
[Classification] INFO
[Explanation] It indicates that trouble occurred in the physical disk (number: ee-ff) of disk
array (name: bbb...b).
For Windows, this message is target of ESMPRO Manager Report.
aa : Internal number indicating physical disk type
bbb...b : Disk array name
ccc...c : Product ID of disk array (S4300 Disk Array etc.)
ddd...d : Serial number of disk array
ee-ff : Physical disk number
ggg...g : Information of RANK or pool where the physical disk belongs
- PoolNo=<xxxx>h PoolName=<yyy...y>
Indicates pool information. (for the disk arrays with pool)
xxxx : Pool number
yyy...y : Pool name
- RankNo=<xx>h-<yy>h
Indicates RANK information. (for other than the disk arrays
with pool)
xx-yy : RANK number
[Measures] Check the status of resource with the trouble and perform the appropriate
maintenance.
Chapter 2 Message List
159
iSM07404: State of PD(<aa>h) has become
attn(rebuilding). (<bbb...b>
productID=<ccc...c> SN=<ddd...d>
No=<ee>h-<ff>h <ggg...g>)
[Classification] NOTICE
[Explanation] It indicates that the physical disk (number: ee-ff) of disk array (name: bbb...b) is
rebuilding data.
aa : Internal number indicating physical disk type
bbb...b : Disk array name
ccc...c : Product ID of disk array (S4300 Disk Array etc.)
ddd...d : Serial number of disk array
ee-ff : Physical disk number
ggg...g : Information of RANK or pool where the physical disk belongs
- PoolNo=<xxxx>h PoolName=<yyy...y>
Indicates pool information. (for the disk arrays with pool)
xxxx : Pool number
yyy...y : Pool name
- RankNo=<xx>h-<yy>h
Indicates RANK information. (for other than the disk arrays
with pool)
xx-yy : RANK number
[Measures] Unnecessary
Chapter 2 Message List
160
iSM07409: State of PD(<aa>h) has become ready.
(<bbb...b> productID=<ccc...c>
SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>)
[Classification] INFO
[Explanation] It indicates that the physical disk (number: ee-ff) of disk array (name: bbb...b)
has completed rebuilding and become ready.
aa : Internal number indicating physical disk type
bbb...b : Disk array name
ccc...c : Product ID of disk array (S4300 Disk Array etc.)
ddd...d : Serial number of disk array
ee-ff : Physical disk number
ggg...g : Information of RANK or pool where the physical disk belongs
- PoolNo=<xxxx>h PoolName=<yyy...y>
Indicates pool information. (for the disk arrays with pool)
xxxx : Pool number
yyy...y : Pool name
- RankNo=<xx>h-<yy>h
Indicates RANK information. (for other than the disk arrays
with pool)
xx-yy : RANK number
[Measures] Unnecessary
Chapter 2 Message List
161
iSM07411: State of POOL has become ready.
(<aaa...a> productID=<bbb...b>
SN=<ccc...c> No=<dddd>h
Name=<eee...e>)
[Classification] INFO
[Explanation] It indicates that the pool (number: dddd, name: eee...e) of a disk array (name:
aaa...a) has become ready.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2800 Disk Array etc.)
ccc…c : Serial number of disk array
dddd : Pool number
eee...e : Pool name
[Measures] Unnecessary
iSM07412: State of POOL has become fault.
(<aaa...a> productID=<bbb...b>
SN=<ccc...c> No=<dddd>h
Name=<eee...e>)[_ALERT_]
[Classification] ERROR
[Explanation] It indicates that trouble occurred in a pool (number: dddd, name: eee...e) of a
disk array (name: aaa...a).
For Windows, this message is target of ESMPRO Manager Report.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2800 Disk Array etc.)
ccc…c : Serial number of disk array
dddd : Pool number
eee...e : Pool name
[Measures] Check the status of the pool with the trouble and perform the appropriate
maintenance.
Chapter 2 Message List
162
iSM07413: State of POOL has become
attn(reduce). (<aaa...a>
productID=<bbb...b> SN=<ccc...c>
No=<dddd>h Name=<eee...e>)
[Classification] ERROR
[Explanation] It indicates that the pool (number: dddd, name: eee...e) of a disk array (name:
aaa...a) has become a reduced state.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2800 Disk Array etc.)
ccc...c : Serial number of disk array
dddd : Pool number
eee...e : Pool name
[Measures] Check the status of the pool with the trouble and perform the appropriate
maintenance.
iSM07414: State of POOL has become
attn(rebuilding). (<aaa...a>
productID=<bbb...b> SN=<ccc...c>
No=<dddd>h Name=<eee...e>)
[Classification] NOTICE
[Explanation] It indicates that the pool (number: dddd, name: eee...e) of a disk array (name:
aaa...a) is rebuilding data.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2800 Disk Array etc.)
ccc...c : Serial number of disk array
dddd : Pool number
eee...e : Pool name
[Measures] In relation to the measures for the pool caused by state transition, refer to other
applicable messages.
Chapter 2 Message List
163
iSM07415: State of POOL has become
attn(preventive copy). (<aaa...a>
productID=<bbb...b> SN=<ccc...c>
No=<dddd>h Name=<eee...e>)
[Classification] NOTICE
[Explanation It indicates that data in a pool (number: dddd, name: eee...e) of a disk array
(name: aaa...a) has been copied into a spare disk.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2800 Disk Array etc.)
ccc…c : Serial number of disk array
dddd : Pool number
eee...e : Pool name
[Measures] Unnecessary
iSM07416: State of POOL has become attn(copy
back). (<aaa...a> productID=<bbb...b>
SN=<ccc...c> No=<dddd>h
Name=<eee...e>)
[Classification] NOTICE
[Explanation] It indicates that data in a pool (number: dddd, name: eee...e) of a disk array
(name: aaa...a) has been restored from a spare disk.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2800 Disk Array etc.)
ccc...c : Serial number of disk array
dddd : Pool number
eee...e : Pool name
[Measures] Unnecessary
Chapter 2 Message List
164
iSM07452: State of PD(<aa>h) has become
info(inactive). (<bbb...b>
productID=<ccc...c> SN=<ddd...d>
No=<ee>h-<ff>h <ggg...g>)
[UC=<hhh...h> FC=<ii>][_ALERT_]
[Classification] INFO
[Explanation] It indicates that trouble occurred in the physical disk (number: ee-ff) of disk
array (name: bbb...b).
For Windows, this message is target of ESMPRO Manager Report, and also to
be target of ALIVE/Express Report via ESMPRO.
aa : Internal number indicating physical disk type
bbb...b : Disk array name
ccc...c : Product ID of disk array (S2800 Disk Array etc.)
ddd...d : Serial number of disk array
ee-ff : Physical disk number
ggg...g : Information of RANK or pool where the physical disk belongs
- PoolNo=<xxxx>h PoolName=<yyy...y>
Indicates pool information. (for the disk arrays with pool)
xxxx : Pool number
yyy...y : Pool name
- RankNo=<xx>h-<yy>h
Indicates RANK information. (for other than the disk arrays
with pool)
xx-yy : RANK number
hhh...h/ii : Maintenance information
[Measures] Check the status of resource with the trouble and perform the appropriate
maintenance.
Chapter 2 Message List
165
iSM07454: State of PD(<aa>h) has become
attn(rebuilding). (<bbb...b>
productID=<ccc...c> SN=<ddd...d>
No=<ee>h-<ff>h <ggg...g>)
[UC=<hhh...h> FC=<ii>]
[Classification] NOTICE
[Explanation] It indicates that the physical disk (number: ee-ff) of disk array (name: bbb...b) is
rebuilding data.
aa : Internal number indicating physical disk type
bbb...b : Disk array name
ccc...c : Product ID of disk array (S2800 Disk Array etc.)
ddd...d : Serial number of disk array
ee-ff : Physical disk number
ggg...g : Information of RANK or pool where the physical disk belongs
- PoolNo=<xxxx>h PoolName=<yyy...y>
Indicates pool information. (for the disk arrays with pool)
xxxx : Pool number
yyy...y : Pool name
- RankNo=<xx>h-<yy>h
Indicates RANK information. (for other than the disk arrays
with pool)
xx-yy : RANK number
hhh...h/ii : Maintenance information
[Measures] Unnecessary
Chapter 2 Message List
166
iSM07459: State of PD(<aa>h) has become ready.
(<bbb...b> productID=<ccc...c>
SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>) [UC=<hhh...h> FC=<ii>]
[Classification] INFO
[Explanation] It indicates that the physical disk (number: ee-ff) of disk array (name: bbb...b)
has rebuilt data and its status has changed to “ready”.
aa : Internal number indicating physical disk type
bbb...b : Disk array name
ccc...c : Product ID of disk array (S2800 Disk Array etc.)
ddd...d : Serial number of disk array
ee-ff : Physical disk number
ggg...g : Information of RANK or pool where the physical disk belongs
- PoolNo=<xxxx>h PoolName=<yyy...y>
Indicates pool information. (2800 series disk array)
xxxx : Pool number
yyy...y : Pool name
- RankNo=<xx>h-<yy>h
Indicates RANK information. (Other than 2800 series disk
array)
xx-yy : RANK number
hhh...h/ii : Maintenance information
[Measures] Unnecessary
Chapter 2 Message List
167
iSM07461: State of POOL has become ready.
(<aaa...a> productID=<bbb...b>
SN=<ccc...c> No=<dddd>h
Name=<eee...e>)
[Classification] INFO
[Explanation] It indicates that the pool (number: dddd, name: eee...e) of a disk array (name:
aaa...a) has become ready.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2800 Disk Array etc.)
ccc...c : Serial number of disk array
dddd : Pool number
eee...e : Pool name
[Measures] Unnecessary
iSM07462: State of POOL has become fault.
(<aaa...a> productID=<bbb...b>
SN=<ccc...c> No=<dddd>h
Name=<eee...e>) [UC=<fff...f>
FC=<gg>][_ALERT_]
[Classification] ERROR
[Explanation] It indicates that trouble occurred in the pool (number: dddd, name: eee...e) of
disk array (name: aaa...a).
For Windows, this message is target of ESMPRO Manager Report, and also to
be target of ALIVE/Express Report via ESMPRO.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2800 Disk Array etc.)
ccc...c : Serial number of disk array
dddd : Pool number
eee...e : Pool name
fff...f/gg : Maintenance information
[Measures] Check the status of the pool with the trouble and perform the appropriate
maintenance.
Chapter 2 Message List
168
iSM07463: State of POOL has become
attn(reduce). (<aaa...a>
productID=<bbb...b> SN=<ccc...c>
No=<dddd>h Name=<eee...e>)
[Classification] ERROR
[Explanation] It indicates that the pool (number: dddd, name: eee...e) of a disk array (name:
aaa...a) has become a reduced state.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2800 Disk Array etc.)
ccc...c : Serial number of disk array
dddd : Pool number
eee...e : Pool name
[Measures] Check the status of the pool with the trouble and perform the appropriate
maintenance.
iSM07464: State of POOL has become
attn(rebuilding). (<aaa...a>
productID=<bbb...b> SN=<ccc...c>
No=<dddd>h Name=<eee...e>)
[Classification] NOTICE
[Explanation] It indicates that the pool (number: dddd, name: eee...e) of a disk array (name:
aaa...a) is rebuilding data.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2800 Disk Array etc.)
ccc...c : Serial number of disk array
dddd : Pool number
eee...e : Pool name
[Measures] In relation to the measures for the pool caused by state transition, refer to other
applicable messages.
Chapter 2 Message List
169
iSM07465: State of POOL has become
attn(preventive copy). (<aaa...a>
productID=<bbb...b> SN=<ccc...c>
No=<dddd>h Name=<eee...e>)
[Classification] NOTICE
[Explanation] It indicates that data in a pool (number: dddd, name: eee...e) of a disk array
(name: aaa...a) has been copied into a spare disk.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2800 Disk Array etc.)
ccc...c : Serial number of disk array
dddd : Pool number
eee...e : Pool name
[Measures] Unnecessary
iSM07466: State of POOL has become attn(copy
back). (<aaa...a> productID=<bbb...b>
SN=<ccc...c> No=<dddd>h
Name=<eee...e>)
[Classification] NOTICE
[Explanation] It indicates that data in a pool (number: dddd, name: eee...e) of a disk array
(name: aaa...a) has been restored from a spare disk.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2800 Disk Array etc.)
ccc...c : Serial number of disk array
dddd : Pool number
eee...e : Pool name
[Measures] Unnecessary
Chapter 2 Message List
170
iSM07501: Request is meaningless(already)
[Explanation] It indicates that the request for starting or terminating the disk array monitoring
has already executed.
This message is output on UNIX system.
[Measures] Unnecessary
iSM07503: Resource table is re-created
[Explanation] It indicates that the request is suspended since the disk array configuration is
changed.
This message is output on UNIX system.
[Measures] Retry.
iSM07504: Entry is not found
[Explanation] It indicates that the request is suspended since the disk array configuration is
changed.
This message is output on UNIX system.
[Measures] Retry after checking the related resources.
iSM07505: Service stopped
[Explanation] It indicates that the request cannot be executed since the iSM is stopped.
This message is output on UNIX system.
[Measures] Unnecessary
Chapter 2 Message List
171
iSM07506: Request cancel
[Explanation] It indicates that the request is cancelled since due to disk array failure, etc.
This message is output on UNIX system.
[Measures] For disk array failure, retry after recovering the disk array. For other cases,
retry after investigating the cause from syslog or iSM operation log.
iSM07507: Disk array is not watched
[Explanation] It indicates that the request cannot be executed since the specified disk array is
not being monitored.
This message is output on UNIX system.
[Measures] Retry after the disk array becomes in the monitoring status.
iSM07509: Disk array is busy(retype later)
[Explanation] It indicates that the request cannot be executed since another request is being
processed for the disk array.
This message is output on UNIX system.
[Measures] Retry after the processing of the request is completed.
iSM07511: Control path failed
[Explanation] It indicates that the request cannot be executed since the disk array failure
occurred.
This message is output on UNIX system.
[Measures] Retry after the disk array is recovered.
Chapter 2 Message List
172
iSM07512: Specified disk array is not managed
[Explanation] It indicates that the specified disk array name is not managed by the iSM server.
This message is output on UNIX system.
[Measures] Retry after checking the disk array name.
iSM07513: Disk array is busy(configuration)
[Explanation] It indicates that the request cannot be executed since the disk array is in the
configuration setting status.
[Measures] Retry after checking that the disk array configuration setting is completed.
iSM07550: Program error has occurred.
(code=<aaa...a>)
[Classification] NOTICE
[Explanation] It indicates that an internal processing error occurred in the state monitoring
process.
This message is output on UNIX system.
aaa...a : Internal error code
[Measures] Investigate the cause with syslog or iSM operation log.
iSM07551: Time out has occurred.
(code=<aaa...a>)
[Classification] NOTICE
[Explanation] It indicates that a timeout occurred in state monitoring process.
aaa...a : Internal error code
[Measures] Investigate the cause with syslog or iSM operation log.
Chapter 2 Message List
173
iSM07552: Invalid parameter has detected.
(code=<aaa...a>)
[Classification] NOTICE
[Explanation] It indicates that invalid parameter has been detected in state monitoring process.
aaa...a : Internal error code
[Measures] Execute again. If the same phenomenon recurs, investigate the cause with
syslog or iSM operation log.
iSM07553: Process killed
[Classification] NOTICE
[Explanation] It indicates that signal reception caused the process end.
This message is output on UNIX system.
[Measures] Execute again. If the same phenomenon recurs, investigate the cause with
syslog or iSM operation log.
iSM07554: Internal communication error has
occurred. (code=<aaa...a>)
[Classification] NOTICE
[Explanation] It indicates that error occurred in the coordination between state monitoring
process and other related process.
aaa...a : Internal error code
[Measures] Execute again. If the same phenomenon recurs, investigate the cause with
syslog or iSM operation log.
Chapter 2 Message List
174
iSM07555: System call error has occurred.
[func=<aaa...a> errno=<bbb...b>]
(code=<ccc...c>)
[Classification] NOTICE
[Explanation] It indicates that system error occurred in state monitoring process.
aaa...a : Function name
bbb...c : Error number
ccc...c : Internal error code
[Measures] Execute again. If the same phenomenon recurs, investigate the cause with
syslog or iSM operation log.
iSM07556: Insufficient resource has detected.
(code=<aaa...a>)
[Classification] NOTICE
[Explanation] It indicates that it failed to allocate the resources for internal processing in state
monitoring process.
aaa...a : Internal error code
[Measures] Execute again. If the same phenomenon recurs, investigate the cause with
syslog or iSM operation log.
iSM07557: This function is not supported
[Explanation] It indicates that you requested the function that is not supported the iSM server.
[Measures] Check the iSM server version.
Chapter 2 Message List
175
iSM07601: Attribute of LD has configured.
(<aaa...a>)
[Classification] NOTICE
[Explanation] It indicates that attribute of LD is configured for the disk array (name: aaa...a).
aaa...a : Disk array name
[Measures] Unnecessary
iSM07602: LD movement terminated. (<aaa...a>)
[Classification] NOTICE
[Explanation] It indicates that configuration information is received again because the
inconsistency is detected in the disk array configuration information after LD
movement is completed for the disk array (name: aaa...a).
aaa...a : Disk array name
[Measures] Unnecessary
iSM07611: Initialization of LD has failed.
(<aaa...a> productID=<bbb...b>
SN=<ccc...c> No=<dddd>h
Name=<eee...e>)
[Classification] NOTICE
[Explanation] It indicates that data initialization is failed for the logical disk (number: dddd,
name: eee...e) in the disk array (name: aaa...a).
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2100 Disk Array etc.)
ccc...c : Serial number of disk array
dddd : Logical disk number
eee...e : Logical disk name
[Measures] Check the status of the resource with the trouble and perform the appropriate
maintenance.
Chapter 2 Message List
176
iSM07616: The capacity of SRA used is over
threshold.(<aaa...a>
productID=<bbb...b> SN=<ccc...c>
No=<dddd>h Name=<eee...e>
capacity=<fff...f>GB
threshold=<ggg...g>GB)
[Classification] WARNING
[Explanation] It indicates that the used capacity of snapshot reserve area (number: dddd and
name: eee...e) in disk array (name: aaa...a) exceeded specified threshold values.
For Windows, this message is target of ESMPRO Manager Report.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2800 Disk Array etc.)
ccc...c : Serial number of disk array
dddd : Pool number of snapshot reserve area
eee...e : Pool name of snapshot reserve area
fff...f : Used capacity of snapshot reserve area
ggg...g : Threshold of snapshot reserve area
[Measures] Expand the snapshot reserve area or delete unnecessary snapshots.
Chapter 2 Message List
177
iSM07617: The capacity of SRA used is under
threshold.(<aaa...a>
productID=<bbb...b> SN=<ccc...c>
No=<dddd>h Name=<eee...e>
capacity=<fff...f>GB
threshold=<ggg...g>GB)
[Classification] INFO
[Explanation] It indicates that the used capacity of pool (number: dddd and name: eee...e) in
disk array (name: aaa...a) fell below specified threshold values.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2800 Disk Array etc.)
ccc...c : Serial number of disk array
dddd : Pool number of snapshot reserve area
eee...e : Pool name of snapshot reserve area
fff...f : Used capacity of snapshot reserve area
ggg...g : Threshold of snapshot reserve area
[Measures] Unnecessary
Chapter 2 Message List
178
iSM07620: Expansion State of POOL has
become normal-end. (<aaa...a>
productID=<bbb...b> SN=<ccc...c>
No=<dddd>h
Name=<eee...e>)[_ALERT_]
[Classification] INFO
[Explanation] It indicates that capacity expansion of a pool (number: dddd, name: eee...e) of a
disk array (name: aaa...a) normally ended.
For Windows, this message is target of ESMPRO Manager Report.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2800 Disk Array etc.)
ccc...c : Serial number of disk array
dddd : Pool number
eee...e : Pool name
[Measures] Unnecessary
iSM07621: Expansion State of POOL has
become expanding. (<aaa...a>
productID=<bbb...b> SN=<ccc...c>
No=<dddd>h
Name=<eee...e>)[_ALERT_]
[Classification] NOTICE
[Explanation] It indicates that the capacity of a pool (number: dddd, name: eee...e) of a disk
array (name: aaa...a) is being expanded.
For Windows, this message is target of ESMPRO Manager Report.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2800 Disk Array etc.)
ccc...c : Serial number of disk array
dddd : Pool number
eee...e : Pool name
[Measures] Unnecessary
Chapter 2 Message List
179
iSM07622: Expansion State of POOL has
become expand-fail. (<aaa...a>
productID=<bbb...b> SN=<ccc...c>
No=<dddd>h
Name=<eee...e>)[_ALERT_]
[Classification] ERROR
[Explanation] It indicates that capacity expansion of a pool (number: dddd, name: eee...e) of a
disk array (name: aaa...a) failed.
For Windows, this message is target of ESMPRO Manager Report.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2800 Disk Array etc.)
ccc...c : Serial number of disk array
dddd : Pool number
eee...e : Pool name
[Measures] Check the state of the pool with the trouble and perform the appropriate
maintenance.
Chapter 2 Message List
180
iSM07670: Expansion State of POOL has
become normal-end. (<aaa...a>
productID=<bbb...b> SN=<ccc...c>
No=<dddd>h
Name=<eee...e>)[ UC=<fff...f>
FC=<gg>][_ALERT_]
[Classification] INFO
[Explanation] It indicates that capacity expansion of a pool (number: dddd, name: eee...e) of a
disk array (name: aaa...a) normally ended.
For Windows, this message is target of ESMPRO Manager Report, and also to
be target of ALIVE/Express Report via ESMPRO.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2800 Disk Array etc.)
ccc...c : Serial number of disk array
dddd : Pool number
eee...e : Pool name
fff…f/gg : Maintenance information
[Measures] Unnecessary
Chapter 2 Message List
181
iSM07671: Expansion State of POOL has
become expanding. (<aaa...a>
productID=<bbb...b> SN=<ccc...c>
No=<dddd>h
Name=<eee...e>)[ UC=<fff...f>
FC=<gg>][_ALERT_]
[Classification] NOTICE
[Explanation] It indicates that the capacity of a pool (number: dddd, name: eee...e) of a disk
array (name: aaa...a) is being expanded.
For Windows, this message is target of ESMPRO Manager Report, and also to
be target of ALIVE/Express Report via ESMPRO.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2800 Disk Array etc.)
ccc...c : Serial number of disk array
dddd : Pool number
eee...e : Pool name
fff…f/gg : Maintenance information
[Measures] Unnecessary
Chapter 2 Message List
182
iSM07672: Expansion State of POOL has
become expand-fail. (<aaa...a>
productID=<bbb...b> SN=<ccc...c>
No=<dddd>h
Name=<eee...e>)[ UC=<fff...f>
FC=<gg>][_ALERT_]
[Classification ERROR
[Explanation] It indicates that capacity expansion of a pool (number: dddd, name: eee...e) of a
disk array (name: aaa...a) failed.
For Windows, this message is target of ESMPRO Manager Report, and also to
be target of ALIVE/Express Report via ESMPRO.
aaa...a : Disk array name
bbb...b : Product ID of disk array (S2800 Disk Array etc.)
ccc...c : Serial number of disk array
dddd : Pool number
eee...e : Pool name
fff…f/gg : Maintenance information
[Measures] Check the state of the pool with the trouble and perform the appropriate
maintenance.
iSM07900: Process is busy when it terminates
emergency.
Unexpected error message may be
generated.
[Classification] WARNING
[Explanation] The state monitoring instructed emergency stop. However, process could not
be stopped immediately.
This message is output on Windows system.
[Measures] Unnecessary
Chapter 2 Message List
183
iSM07950: Illegal write data has been detected.
(<aaa...a>, LD=<bbb...b>(<cccc>h),
host-info=<ddd...d>)
[Classification] WARNING
[Explanation] It indicates that an invalid write request on disk array was detected by data
retention function.
aaa...a : Name of disk array that detected invalid write request.
bbb...b : Name of logical disk that detected invalid write request.
cccc : Number of logical disk that detected invalid write request.
ddd...d : Server location on which illegal data writing was requested,
indicated by World Wide Port Name (WWPN) of Host Bus
Adapter (HBA).
[Measures] Locate a fault, and re-execute transaction as required.
iSM07981: Message output failed (<aaa...a>)
[Classification] NOTICE
[Explanation] It indicates that it failed to output the message in state monitoring process.
aaa...a : Contents of message to be output
[Measures] Investigate the cause with syslog or iSM operation log.
Chapter 2 Message List
184
iSM08000∼
iSM08020: Disk array=<aaa...a> logging is
started interval=<bb>
[Classification] INFO
[Explanation] It indicates that data accumulation started on statistic information history file.
aaa...a : Disk array name
bb : Accumulation interval (minute)
[Measures] Unnecessary
iSM08021: Disk array=<aaa...a> logging is
stopped
[Classification] INFO
[Explanation] It indicates that accumulation into statistics information history file has been
stopped.
aaa...a : Disk array name
[Measures] Unnecessary
iSM08022: Disk array=<aaa...a> logging interval
has changed interval=<bb>
[Classification] NOTICE
[Explanation] It indicates that data accumulation changed interval on statistic information
history file.
aaa...a : Disk array name
bb : Accumulation interval after change (minute)
[Measures] Unnecessary
Chapter 2 Message List
185
iSM08030: Disk array=<aaa...a> logging is
already started
[Classification] NOTICE
[Explanation] It indicates that accumulation into statistics information history file has already
been started.
aaa...a : Disk array name
[Measures] Check whether the specified disk array name is correct.
iSM08031: Disk array=<aaa...a> logging is
already stopped
[Classification] NOTICE
[Explanation] It indicates that accumulation into statistics information history file has already
been stopped.
aaa...a : Disk array name
[Measures] Check whether the specified disk array name is correct.
iSM08032: Disk array=<aaa...a> is not monitored
[Classification] NOTICE
[Explanation] It indicates that specified disk array is not monitored.
aaa...a : Disk array name
[Measures] Start the accumulation of statistics information or perform the stop operation,
after setting the disk array as a monitoring object.
Chapter 2 Message List
186
iSM08033: Disk array=<aaa...a> does not exist
[Classification] NOTICE
[Explanation] The following status is indicated.
(1) The specified disk array does not exist.
(2) PerformanceMonitor has not been purchased for specified disk array
aaa...a : Disk array name
[Measures] Specify the correct disk array name.
iSM08034: There is no disk array
[Classification] NOTICE
[Explanation] It indicates that there was no object disk array when batch operation (-a option)
of starting/stopping accumulation into statistics information history file, was
executed for all disk array with a prf_start command.
This message is output on UNIX system.
[Measures] Check the status of disk array and if necessary, execute the command again.
iSM08035: Disk array=<aaa...a> logging is
started(overload) interval=<bb>
[Classification] NOTICE
[Explanation] It indicates that accumulation into statistics information history file has been
started. But disk array has become overloaded as a result of acquisition of
statistics information.
aaa...a : Disk array name
bb : Accumulation interval after change (minute)
[Measures] If over-loading of disk array effects on the process, stop the accumulation.
Chapter 2 Message List
187
iSM08036: Disk array=<aaa...a> is overload
[Classification] NOTICE
[Explanation] It indicates that accumulation of statistics information cannot be started due to
the following causes.
(1) There are so many disk array components that statistic information cannot
be collected by specified logging interval.
(2) The disk array is failed.
aaa...a : Disk array name
[Measures] Take an appropriate measure according to the cause:
Measures against Cause (1):
- Specify the automatic logging interval adjustment in the iSM server
environmental definition. This will set the optimal logging interval, avoiding
accumulation start failure.
- You may be able to start statistic information accumulation by decreasing the
display refresh rate of performance monitoring screen or the number of real-time
monitoring items.
Measures against Cause (2):
- Stop monitoring and perform troubleshooting. After troubleshooting, re-start
monitoring and start statistic information accumulation.
iSM08037: Disk array=<aaa...a> is overload
limit=<bbbb> residual=<cccc>
[Classification] NOTICE
[Explanation] It indicates that disk array is overloaded.
aaa...a : Disk array name
bbbb : Upper limit of count for statistic information collection process
(times/minute)
cccc : Number of additional devices allowed for real-time monitoring
[Measures] Addition of real-time monitoring devices is allowed up to cccc. For adding
more devices to be monitored, remove a cause of overloading.
Chapter 2 Message List
188
iSM08050: Performance data is over threshold
(disk array=<aaa...a> [, type=<bbbb>]
[, number=<cccc>] : <dddddddd>
<value =<eee...e> (<ffff>),
threshold=<ggg...g>(<ffff>)>)
[Classification] WARNING
[Explanation] Performance data of components in disk array exceeded specified threshold
values.
aaa...a : Disk array name
bbbb : Calculation unit
PORT : Port
CHESEG : Cache segment
LD : Logical Disk
PD : Physical Disk
cccc : Component ID number
dddddddd : Monitoring item
iops : I/O Density
rate : Transfer Rate
avlen : Average Transfer Length
avresp : Average Response Time
readhit : Read Hit Ratio
writehit : Write Hit Ratio
busy : Busy Ratio
eee...e : Performance data value
ffff : Monitoring item value
ggg...g : Threshold value
[Measures] Research the access status of components with exceeded thresholds as necessary.
iSM08051: Performance monitoring overhead
exceeds permissible amount (disk
array=<aaa...a>)
[Classification] NOTICE
[Explanation] It indicates that disk array has become overloaded.
aaa...a : Disk array name
[Measures] Because performance monitoring has been continued, perform measures such as
reducing components and release the overload status.
Chapter 2 Message List
189
iSM08052: Threshold monitoring condition has
changed interval=<aa>(<bbb>)
border=<ccc>
[Classification] NOTICE
[Explanation] It indicates that threshold monitoring conditions have been changed.
aa : Threshold monitoring interval
bbb : Unit of threshold monitoring interval (min or sec)
ccc : Minimum number of I/Os
[Measures] Unnecessary
iSM08053: Condition to reset threshold excess
state has changed interval=<aa>
time=<bb>:<cc>
[Classification] NOTICE
[Explanation] It indicates that threshold excess release conditions have been changed.
aa : Threshold excess release interval (threshold monitoring count)
* If no value is specified, asterisk is displayed (interval=*)
bb:cc : Threshold excess release time
* If no value is specified, asterisk is displayed (time=**:**)
[Measures] Unnecessary
Chapter 2 Message List
190
iSM08054: Threshold excess state has been
reset [Disk
array=<aaa...a>][type=<bbbb>][numb
er=<cccc>][<<dddddddd>>]
[Classification] NOTICE
[Explanation] Threshold excess status has been released automatically.
aaa...a : Disk array name
bbbb : Calculation unit
PORT : Port
CHESEG : Cache segment
LD : Logical Disk
PD : Physical Disk
cccc : Component ID number
dddddddd : Monitoring item
iops : I/O Density
rate : Transfer Rate
avlen : Average Transfer Length
avresp : Average Response Time
readhit : Read Hit Ratio
writehit : Write Hit Ratio
busy : Busy Ratio
[Measures] Unnecessary
iSM08055: Saving of threshold monitoring
object failed ([disk array=<aaa...a>]
[func=<bbb...b>] [errno=<cccc>]
[detcode=<dddddddd>])
[Classification] WARNING
[Explanation] It indicates that storing of threshold value failed.
aaa...a : Disk array name
bbb...b : Name of function in which an error occurred.
cccc : Error number
dddddddd : Detail code
[Measures] Disk space shortage and file system failure are suspected. Remove a cause of
error and restart the iSM server. Then, specify a threshold on the performance
monitor screen again.
Chapter 2 Message List
191
iSM08056: Restoration of threshold monitoring
object failed ([disk array=<aaa...a>]
[func=<bbb...b>] [errno=<cccc>]
[detcode=<dddddddd>])
[Classification] WARNING
[Explanation] It indicates that restoration of threshold value failed.
aaa...a : Disk array name
bbb...b : Name of function in which an error occurred.
cccc : Error number
dddddddd : Detail code
[Measures] Input error of threshold saving file or shortened display refresh rate is suspected
as a possible cause. Against an input error of threshold saving file, remove the
cause of file system failure and then restart the iSM server. Against shortened
display refresh rate (detcode=01660086), restore the display refresh rate to a
previous value or specify a threshold value on the performance monitoring
screen again.
Chapter 2 Message List
192
iSM08060: Psl file {open|access|close} error
func=<aaa...a> errno=<bbbb>
detcode=<cccccccc> file=<ddd...d>
[Classification] WARNING
[Explanation] It indicates that error occurred in open/access/close of statistics information
history file.
aaa...a : Function name with error.
bbbb : Error number
cccccccc : Detail code of error
ddd...d : File name
The followings are the main reasons for this message output.
y Opening process failed because there was no directory defined in the
environment definition file.
errno=2
detcode=0122f026
y Opening process failed because the directory defined in the environment
definition file has no writing permission.
errno=13
detcode=0122f026,0122f025
y It failed in the open/access/close processing of statistics information history
file due to shortage of disk space.
errno=2,4,28
detcode=0122f026,01220031,01220032,0122f033,0122f035,01230013,012300
14,01260030, 01260031,01100002,0122f011,0122f025
y Access error of disk occurred.
errno=5
detcode=01220031,01220032,0122f033,0122f035,01230013,01230014,01260
030,01260031
[Measures] Remove the cause of trouble.
iSM08061: Psl file sequence number is over max
value
[Classification] WARNING
[Explanation] It indicates that the sequence number of the statistics information history file has
been over the maximum value.
[Measures] Save or delete the statistics information history file and restart the iSM server.
Chapter 2 Message List
193
iSM08062: Psl file name is over max value
[Classification] WARNING
[Explanation] It indicates that file name of statistics information history file has been over the
maximum value.
[Measures] Review the file name of statistics information history file or the storage
directory.
iSM08063: Psl file already exist (disk array=
<aaa...a> file=<bbb...b>)
[Classification] INFO
[Explanation] It indicates that a statistics information history file has already existed. In this
case, a new file is created by assigning a file sequence number to the existing
statistics information history file name, and accumulation of statistics
information will normally start.
aaa...a : Disk array name
bbb...b : File name finally determined
[Measures] Unnecessary
iSM08070: Make directory failed
dirname=<aaa...a> errno=<bbbb>
detcode=<cccccccc>
[Classification] NOTICE
[Explanation] It indicates that it failed to create the directory.
aaa...a : Directory name
bbbb : Error code
cccccccc : Detail code
[Measures] Remove the cause of trouble and restart the iSM server.
Chapter 2 Message List
194
iSM08071: Change directory failed
dirname=<aaa...a> errno=<bbbb>
detcode=<cccccccc>
[Classification] NOTICE
[Explanation] It indicates that it failed to change the directory.
aaa...a : Directory name
bbbb : Error code
cccccccc : Detail code
[Measures] Remove the cause of trouble and restart the iSM server.
iSM08072: Insufficient resource detected
func=<aaa...a> errno=<bbbb>
detcode=<cccccccc>
[Classification] NOTICE
[Explanation] It indicates that it failed to reserve resources.
aaa...a : Function name
bbbb : Error code
cccccccc : Detail code
[Measures] Remove the cause of trouble and restart the iSM server.
iSM08091: To create process failed
func=<aaa...a> errno=<bbbb>
detcode=<cccccccc>
[Classification] NOTICE
[Explanation] It indicates that it failed to generate the internal process.
aaa...a : Function name
bbbb : Error code
cccccccc : Detail code
[Measures] Check whether there is no fault in the operation environment of iSM server and
restart it.
Chapter 2 Message List
195
iSM08092: To get performance data failed from
disk array=<aaa...a> type=<bbb...b>
number=<cccc> detcode=<dddddddd>
[Classification] NOTICE
[Explanation] It indicates that I/O error occurred in disk array collecting statistics information.
aaa...a : Disk array name
bbb...b : Type of failed information
SYSTEM (MNT) : Maintenance information of disk array
SYSTEM (INQ) : Attribute information of disk array
HD : Statistics information of HD
RD : Statistics information of RD
DD : Statistics information of DD
CACHE : Statistics information of CACHE
CHESEG : Statistics information of CHESEG
LD : Statistics information of LD
PD : Statistics information of PD
RANK : Statistics information of RANK
POOL : Statistics information of POOL
cccc : ID number of component of failed information
dddddddd : Detail code
[Measures] Investigate the state of disk array and remove the cause of trouble.
iSM08093: Failed in communication with <aaaa>
[func=<bbb...b>] [errno=<cccc>]
detcode=<dddddddd>
[Classification] NOTICE
[Explanation] It indicates that error occurred in internal communication control.
aaaa : Destination of communication
bbb...b : Function name
cccc : Error code
dddddddd : Detail code
[Measures] Collect necessary information according to the iSM error information collection
procedure, and restart the iSM server.
Chapter 2 Message List
196
iSM08094: System call error occurred
func=<aaa...a> errno=<bbbb>
detcode=<cccccccc>
[Classification] NOTICE
[Explanation] It indicates that abnormalities occurred in iSM server operation.
aaa...a : Function name
bbbb : Error code
cccccccc : Detail code
[Measures] Restart iSM server.
iSM08099: Program error occurred
detcode=<aaaaaaaa>
[Classification] NOTICE
[Explanation] It indicates that internal contradiction has been detected.
aaaaaaaa : Detail code
[Measures] Restart iSM server.
iSM08180: Accept new display refresh rate(<a>
times/minute old=<b>)
[Classification] NOTICE
[Explanation] Display refresh rate was changed.
a : Specified refresh rate
b : Refresh rate before change
[Measures] Unnecessary
Chapter 2 Message List
197
iSM08181: Specified value is the same as
current value(<a> times/minute)
[Classification] NOTICE
[Explanation] The specified value is same as current display refresh rate. The command will be
ignored.
a : Specified refresh rate
[Measures] Unnecessary
iSM08182: Can’t change display refresh
rate(<aaa...a>:<bbb...b>)
[Classification] NOTICE
[Explanation] Display refresh rate cannot be changed for the causes shown in aaa...a.
aaa...a : cause
- stop all clients:
Refresh rate cannot be changed because a performance
monitoring screen is displayed.
- reduce threshold monitoring object:
Refresh rate cannot be changed due to excess number of
threshold monitoring object.
bbb...b : Disk array name
[Measures] Take the measures below.
- If the change was failed because a performance monitoring client was being
connected. (stop all clients)
Terminate all performance monitoring clients, then execute the command
again.
- If the change was failed due to excess number of threshold monitoring object.
(reduce threshold monitoring object) Reduce the threshold monitoring
objects from performance monitoring clients, execute the command again.
Chapter 2 Message List
198
iSM08183: Specified value is not allowed as
display refresh rate(<a>
times/minute)
[Classification] NOTICE
[Explanation] The specified value is not allowed as a display refresh rate.
a : Specified refresh rate
[Measures] Review the specified value.
iSM08201: Illegal performance data was
received from disk array=<aaa...a>
type=<bbbb> number=<cccc>
detcode=<dddddddd>
[Classification] NOTICE
[Explanation] Performance data collected from HW is illegal.
aaa...a : Disk array name
bbbb : Type of performance data
HD : Statistical information of HD
RD : Statistics information of RD
DD : Statistical information of DD
CHESEG : Statistics information of CHESEG
LD : Statistical information of LD
PD : Statistical information of PD
RANK : Statistical information of RANK
POOL : Statistics information of POOL
cccc : Component ID number
dddddddd : Detail code
[Measures] Collect necessary information according to the iSM error information collection
procedure, and restart the iSM server.
Chapter 2 Message List
199
iSM08900: Process busy when terminate
emergency. unexpected error
message maybe generated.
[Classification] WARNING
[Explanation] The performance monitoring instructed emergency stop. However, process
could not be stopped immediately.
This message is output on Windows system.
[Measures] Unnecessary
Chapter 2 Message List
200
iSM09000 ∼
iSM09001: System call error occurred
func=<aaa...a> errno=<bbbb>
detcode=<cccccccc>
[Classification] NOTICE
[Explanation] It indicates that an error occurred in iSM server operation.
aaa...a : Function name
bbbb : Error code
cccccccc : Detail code
[Measures] Restart iSM server.
iSM09002: Start LD movement from
<aaaa>(<bbb...b>) to
<cccc>(<ddd...d>) in <eee...e>
[Classification] NOTICE
[Explanation] It indicates that the logical disk movement starts.
aaaa : Logical disk number of moved material logical disk
bbb...b : Logical disk name of moved material logical disk
cccc : Logical disk number of work disk for Optimization
ddd...d : Logical disk name of work disk for Optimization
eee...e : Disk array name
[Measures] Unnecessary
Chapter 2 Message List
201
iSM09003: LD movement from <aaaa>(<bbb...b>)
to <cccc>(<ddd...d>) in <eee...e>
<fff...f>
[Classification] NOTICE
[Explanation] It indicates that the logical disk movement process has been completed.
aaaa : Logical disk number of moved material logical disk
bbb...b : Logical disk name of moved material logical disk
cccc : Logical disk number of work disk for Optimization
ddd...d : Logical disk name of work disk for Optimization
eee...e : Disk array name
fff...f : Error cause
terminated successfully : Moving of the logical disk
terminated normally.
terminated unsuccessfully : Moving of the logical disk
terminated abnormally.
stopped by user request : The movement process suspended
by user request.
[Measures] Take the measures below.
y terminated successfully
Unnecessary
y terminated unsuccessfully
Correct the specified conditions and execute the process again.
y stopped by user request
Unnecessary
Chapter 2 Message List
202
iSM09004: Changed LD movement speed from
<aaaa>(<bbb...b>) to
<cccc>(<ddd...d>) in <eee...e>
[Classification] NOTICE
[Explanation] It indicates that the logical disk movement speed is changed.
aaaa : Logical disk number of moved material logical disk
bbb...b : Logical disk name of moved material logical disk
cccc : Logical disk number of work disk for Optimization
ddd...d : Logical disk name of work disk for Optimization
eee...e : Disk array name
[Measures] Unnecessary
iSM09005: Insufficient resource detected
func=<aaa...a> errno=<bbbb>
detcode=<cccccccc>
[Classification] NOTICE
[Explanation] It indicates that it has failed to acquire sufficient memory.
aaa...a : Function name
bbbb : Error code
cccccccc : Detail code
[Measures] Remove the cause of the error and restart the iSM server.
Chapter 2 Message List
203
iSM09006: Failed in communication with <aaaa>
func=<bbb...b> errno=<cccc>
detcode=<dddddddd>
[Classification] NOTICE
[Explanation] It indicates that an error has occurred on the internal communication process.
aaaa : Communication target
bbb...b : Function name
cccc : Error code
dddddddd : Detail code
[Measures] Remove the cause of the error and restart the iSM server.
iSM09007: To create process failed
func=<aaa...a> errno=<bbbb>
detcode=<cccccccc>
[Classification] NOTICE
[Explanation] It indicates that it has failed to create internal process.
aaa...a : Function name
bbbb : Error code
cccccccc : Detail code
[Measures] Remove the cause of the error and restart the iSM server.
Chapter 2 Message List
204
iSM09008: Make directory failed
dirname=<aaa...a> func=<bbb...b>
errno=<cccc> detcode=<dddddddd>
[Classification] NOTICE
[Explanation] It indicates that it has failed to create the directory.
aaa...a : Directory name
bbb...b : Function name
cccc : Error code
dddddddd : Detail code
[Measures] Remove the cause of the error and restart the iSM server.
iSM09009: Change directory failed
dirname=<aaa...a> func=<bbb...b>
errno=<cccc> detcode=<dddddddd>
[Classification] NOTICE
[Explanation] It indicates that it has failed to move the directory.
aaa...a : Directory name
bbb...b : Function name
cccc : Error code
dddddddd : Detail code
[Measures] Remove the cause of the error and restart the iSM server.
Chapter 2 Message List
205
iSM09010: Request of start LD movement from
<aaaa>(<bbb...b>) to
<cccc>(<ddd...d>) in <eee...e> is
rejected detcode=<ffffffff>
[Classification] NOTICE
[Explanation] It indicates that the request to move the logical disk was rejected.
aaaa : Logical disk number of moved material logical disk
bbb...b : Logical disk name of moved material logical disk
cccc : Logical disk number of work disk for Optimization
ddd...d : Logical disk name of work disk for Optimization
eee...e : Disk array name
ffffffff : Detail code
[Measures] Check whether or not an error has occurred on the disk array based on the
information shown in other messages. If there is an error, remove the cause of
the error and execute the process again.
iSM09011: Request of stop LD movement from
<aaaa>(<bbb...b>) to
<cccc>(<ddd...d>) in <eee...e> is
rejected detcode=<ffffffff>
[Classification] NOTICE
[Explanation] It indicates that the request to suspend moving process of the logical disk was
rejected.
aaaa : Logical disk number of moved material logical disk
bbb...b : Logical disk name of moved material logical disk
cccc : Logical disk number of work disk for Optimization
ddd...d : Logical disk name of work disk for Optimization
eee...e : Disk array name
ffffffff : Detail code
[Measures] Take the measures below.
y Check the specification of the logical disk for which the movement is
suspended.
y Check for the disk array status according to the related messages, eliminate
the error cause (e.g., error recovery), and then re-execute the command.
Chapter 2 Message List
206
iSM09012: Request of change LD movement
speed from <aaaa>(<bbb...b>) to
<cccc>(<ddd...d>) in <eee...e> is
rejected detcode=<ffffffff>
[Classification] NOTICE
[Explanation] It indicates that the request to change the logical disk movement speed was
rejected.
aaaa : Logical disk number of moved material logical disk
bbb...b : Logical disk name of moved material logical disk
cccc : Logical disk number of work disk for Optimization
ddd...d : Logical disk name of work disk for Optimization
eee...e : Disk array name
ffffffff : Detail code
[Measures] Take the measures below.
y Check the specification of the logical disk for which the movement speed is
changed.
y Check for the disk array status according to the related messages, eliminate
the error cause (e.g., error recovery), and then re-execute the command.
iSM09013: To get subsystem information failed
from disk array=<aaa...a>
detcode=<bbbbbbbb>
[Classification] NOTICE
[Explanation] It indicates that the attempt to obtain such information related to the disk array as
configuration and attribution failed.
aaa...a : Disk array name
bbbbbbbb : Detail code
[Measures] Find the cause of the error on the disk array based on the information shown in
other messages, remove the cause and resume monitoring.
Chapter 2 Message List
207
iSM09014: Failed in termination of LD movement
from <aaaa>(<bbb...b>) to
<cccc>(<ddd...d>) in <eee...e>
detcode=<ffffffff>
[Classification] NOTICE
[Explanation] It indicates that the attempt to terminate the logical disk movement process
failed.
aaaa : Logical disk number of moved material logical disk
bbb...b : Logical disk name of moved material logical disk
cccc : Logical disk number of work disk for Optimization
ddd...d : Logical disk name of work disk for Optimization
eee...e : Disk array name
ffffffff : Detail code
[Measures] Find the cause of the error on the disk array based on the information shown in
other messages, remove the cause and resume monitoring. When monitoring is
resumed, the termination process for the logical disk movement is executed
again.
iSM09015: Illegal LD movement information was
received from <aaa...a>
[Classification] NOTICE
[Explanation] It indicates that the following abnormality occurred in moving of logical disks.
(1) The movement information of the logical disk included illegal information.
(2) Issuing of requests regarding moving logical disks failed.
aaa...a : Disk array name
[Measures] Take the measures below.
(1) Collect information necessary for checking the error cause according to the
iSM error information collection procedure.
(2) Find the cause of the error on the disk array based on the information shown
in other messages, remove the cause and resume monitoring.
Chapter 2 Message List
208
iSM09016: The schedule of LD movement from
<aaaa>(<bbb...b>) to <cccc>
(<ddd...d>) in <eee...e> registered.
schedule time=<ffff>/<gg>/<hh>
<ii>:<jj> range=<kk>
[Classification] NOTICE
[Explanation] It indicates that moving schedule of logical disks has been registered.
aaaa : Logical disk number of moved material logical disk
bbb...b : Logical disk name of moved material logical disk
cccc : Logical disk number of work disk for Optimization
ddd...d : Logical disk name of work disk for Optimization
eee...e : Disk array name
ffff/gg/hh ii:jj : Scheduled start time of moving logical disks (year/month/day
hour:minute)
kk : Re-execution continuing time when the Logical Disk could not
be moved at scheduled time (1 to 24, unit: hour)
[Measures] Unnecessary
iSM09017: Request to register the schedule of
LD movement from <aaaa>(<bbb...b>)
to <cccc>(<ddd...d>) in <eee...e>
rejected. detcode=<ffffffff>
[Classification] NOTICE
[Explanation] It indicates that registering of moving schedule of logical disks failed.
aaaa : Logical disk number of moved material logical disk
bbb...b : Logical disk name of moved material logical disk
cccc : Logical disk number of work disk for Optimization
ddd...d : Logical disk name of work disk for Optimization
eee...e : Disk array name
ffffffff : Detail code
[Measures] Remove a cause of the failure with references to other related messages, and
retry registration.
Chapter 2 Message List
209
iSM09018: The schedule of LD movement from
<aaaa>(<bbb...b>) to <cccc>
(<ddd...d>) in <eee...e> deleted.
[Classification] NOTICE
[Explanation] It indicates that moving schedule of registered logical disks has been canceled.
aaaa : Logical disk number of moved material logical disk
bbb...b : Logical disk name of moved material logical disk
cccc : Logical disk number of work disk for Optimization
ddd...d : Logical disk name of work disk for Optimization
eee...e : Disk array name
[Measures] Unnecessary
iSM09019: Request to delete the schedule of LD
movement from <aaaa>(<bbb...b>) to
<cccc>(<ddd...d>) in <eee...e>
rejected. detcode=<ffffffff>
[Classification] NOTICE
[Explanation] It indicates that canceling of moving schedule of logical disks failed.
aaaa : Logical disk number of moved material logical disk
bbb...b : Logical disk name of moved material logical disk
cccc : Logical disk number of work disk for Optimization
ddd...d : Logical disk name of work disk for Optimization
eee...e : Disk array name
ffffffff : Detail code
[Measures] Remove a cause of the failure with references to other related messages, and
retry registration.
Chapter 2 Message List
210
iSM09020: The schedule of LD movement from
<aaaa>(<bbb...b>) to <cccc>
(<ddd...d>) in <eee...e> changed.
schedule time=<ffff>/<gg>/<hh>
<ii>:<jj> range=<kk>
[Classification] NOTICE
[Explanation] It indicates that moving schedule of registered logical disks has been changed.
aaaa : Logical disk number of moved material logical disk
bbb...b : Logical disk name of moved material logical disk
cccc : Logical disk number of work disk for Optimization
ddd...d : Logical disk name of work disk for Optimization
eee...e : Disk array name
ffff/gg/hh ii:jj : Scheduled start time of moving logical disks (year/month/day
hour:minute)
kk : Re-execution continuing time when the Logical Disk could not
be moved at scheduled time (1 to 24, unit: hour)
[Measures] Unnecessary
iSM09021: Request to change the schedule of
LD movement from <aaaa>(<bbb...b>)
to <cccc>(<ddd...d>) in <eee...e>
rejected. detcode=<ffffffff>
[Classification] NOTICE
[Explanation] It indicates that changing of moving schedule of logical disks failed.
aaaa : Logical disk number of moved material logical disk
bbb...b : Logical disk name of moved material logical disk
cccc : Logical disk number of work disk for Optimization
ddd...d : Logical disk name of work disk for Optimization
eee...e : Disk array name
ffffffff : Detail code
[Measures] Remove a cause of the failure with references to other related messages, and
retry changing.
Chapter 2 Message List
211
iSM09022: Failed to start the scheduled LD
movement from <aaaa>(<bbb...b>) to
<cccc>(<ddd...d>) in <eee...e>.
detcode=<ffffffff>
[Classification] NOTICE
[Explanation] It indicates that a logical disk to which the moving schedule has been registered
cannot be started to move within the re-execution continuing time, or that it
cannot be started to move because its configuration is changed.
aaaa : Logical disk number of moved material logical disk
bbb...b : Logical disk name of moved material logical disk
cccc : Logical disk number of work disk for Optimization
ddd...d : Logical disk name of work disk for Optimization
eee...e : Disk array name
ffffffff : Detail code
[Measures] Retry moving of logical disks of failed moving process, or re-register the moving
schedule.
iSM09099: Program error occurred
detcode=<aaaaaaaa>
[Classification] NOTICE
[Explanation] It indicates that internal contradiction is detected.
aaaaaaaa : Detail code
[Measures] Collect information necessary for checking the error cause according to the iSM
error information collection procedure.
Chapter 2 Message List
212
iSM09101: Bsl file open failed func=<aaa...a>
errno=<bbbb> detcode=<cccccccc>
filename=<ddd...d>
[Classification] WARNING
[Explanation] Failed to open the Bsl file.
aaa...a : Function name
bbbb : Error code
cccccccc : Detail code
ddd...d : Bsl file name
[Measures] Check the Bsl file and the file system, remove the cause of the error and restart
the iSM server.
iSM09102: Bsl file remove failed func=<aaa...a>
errno=<bbbb> detcode=<cccccccc>
filename=<ddd...d>
[Classification] WARNING
[Explanation] Failed to delete the Bsl file.
aaa...a : Function name
bbbb : Error code
cccccccc : Detail code
ddd...d : Bsl file name
[Measures] Check the Bsl file and the file system, remove the cause of the error and restart
the iSM server.
Chapter 2 Message List
213
iSM09103: Bsl file rename failed func=<aaa...a>
errno=<bbbb> detcode=<cccccccc>
filename=<ddd...d>
[Classification] WARNING
[Explanation] Failed to change the Bsl file name.
aaa...a : Function name
bbbb : Error code
cccccccc : Detail code
ddd...d : Bsl file name
[Measures] Check the Bsl file and the file system, remove the cause of the error and restart
the iSM server.
iSM09104: Bsl file write failed func=<aaa...a>
errno=<bbbb> detcode=<cccccccc>
[rankno=<dddd>] filename=<eee...e>
[Classification] WARNING
[Explanation] Failed to write to the Bsl file.
aaa...a : Function name
bbbb : Error code
cccccccc : Detail code
dddd : RANK number of the data that could not be written
eee...e : Bsl file name
[Measures] Check the Bsl file and the file system, remove the cause of the error and restart
the iSM server.
Chapter 2 Message List
214
iSM09105: Bsl file seek failed func=<aaa...a>
errno=<bbbb> detcode=<cccccccc>
[rankno=<dddd>] filename=<eee...e>
[Classification] WARNING
[Explanation] Seek in the Bsl file failed.
aaa...a : Function name
bbbb : Error code
cccccccc : Detail code
dddd : RANK number of the data that could not be positioned
eee...e : Bsl file name
[Measures] Check the Bsl file and the file system, remove the cause of the error and restart
the iSM server.
iSM09106: Bsl file read failed func=<aaa...a>
errno=<bbbb> detcode=<cccccccc>
[rankno=<dddd>] filename=<eee...e>
[Classification] WARNING
[Explanation] Failed to read the Bsl file.
aaa...a : Function name
bbbb : Error code
cccccccc : Detail code
dddd : RANK number of the data that could not be read
eee...e : Bsl file name
[Measures] Check the Bsl file and the file system, remove the cause of the error and restart
the iSM server.
Chapter 2 Message List
215
iSM09107: Bsl file close failed func=<aaa...a>
errno=<bbbb> detcode=<cccccccc>
filename=<ddd...d>
[Classification] WARNING
[Explanation] Failed to close the Bsl file.
aaa...a : Function name
bbbb : Error code
cccccccc : Detail code
ddd...d : Bsl file name
[Measures] Check the Bsl file and the file system, remove the cause of the error and restart
the iSM server.
iSM09108: Bsl file re-created (illegal format
detected detcode=<aaaaaaaa>)
[Classification] NOTICE
[Explanation] The Bsl file format was illegal when the iSM server was previously operated,
and the Bsl file was re-created.
aaaaaaaa : Detail code
[Measures] Unnecessary
Chapter 2 Message List
216
iSM10000 ∼
iSM10001: comm error: main sc=<aaa>h
ec=<bbb...b>h
[Classification] NOTICE
[Explanation] It indicates that it failed in connection/disconnection to iSM server.
aaa : Code indicating location of error
bbb...b : Error code
[Measures] Check whether abnormalities have occurred in the configuring process on the
iSM server machine and restart the iSM server.
iSM10002: comm error: main sc=<aaa>h
ec=<bbb...b>h
[Classification] NOTICE
[Explanation] It indicates that it failed to initialize communication function to iSM server.
aaa : Code indicating location of error
bbb...b : Error code
[Measures] Check whether abnormalities have occurred in the configuring process on the
iSM server machine and restart the iSM server.
iSM10020: sys error: main sc=<aaa>h
ec=<bbb...b>h
[Classification] ERROR
[Explanation] It indicates that it failed in system call at the time of starting/termination.
aaa : Code indicating location of error
bbb...b : Error code
[Measures] Check whether abnormalities (such as insufficient memory) have occurred in the
operation environment of iSM server machine and restart the iSM server.
Chapter 2 Message List
217
iSM10040: func error: main sc=<aaa>h
ec=<bbb...b>h
[Classification] NOTICE
[Explanation] It indicates that abnormal termination occurred in the state monitoring function
of replication management.
aaa : Code indicating location of error
bbb...b : Error code
[Measures] Check whether abnormalities have occurred in the configuring process on the
iSM server machine and restart the iSM server.
iSM10100: comm error: Agent sc=<aaa>h
ec=<bbb...b>h
[Classification] NOTICE
[Explanation] It indicates that it failed to initialize communication function to iSM server.
aaa : Code indicating location of error
bbb...b : Error code
[Measures] Check whether abnormalities have occurred in the configuring process on the
iSM server machine and restart the iSM server.
iSM10101: comm error: Agent sc=<aaa>h
ec=<bbb...b>h
[Classification] NOTICE
[Explanation] It indicates that it failed to process the telegram transmission to disk array.
aaa : Code indicating location of error
bbb...b : Error code
[Measures] Check whether abnormalities have occurred in the configuring process on the
iSM server.
Chapter 2 Message List
218
iSM10102: comm error: Agent sc=<aaa>h
ec=<bbb...b>h
[Classification] NOTICE
[Explanation] It indicates that it failed to process the telegram receiving from disk array.
aaa : Code indicating location of error
bbb...b : Error code
[Measures] Check whether abnormalities have occurred in the configuring process on the
iSM server.
iSM10103: sys error: Agent sc=<aaa>h
ec=<bbb...b>h
[Classification] ERROR
[Explanation] It indicates that it failed in system call when telegram sending/receiving from
disk array.
aaa : Code indicating location of error
bbb...b : Error code
[Measures] Check whether abnormalities (such as insufficient memory) have occurred in the
operation environment of iSM server.
iSM10104: func error: Agent sc=<aaa>h
ec=<bbb...b>h
[Classification] NOTICE
[Explanation] It indicates that it failed to acquire the information from iSM server.
aaa : Code indicating location of error
bbb...b : Error code
[Measures] Check whether abnormalities have occurred in the configuring process on the
iSM server.
Chapter 2 Message List
219
iSM10106: DiskArrayName(=<aaa...a>) has
changed
[Classification] NOTICE
[Explanation] Specified disk array name has been changed.
aaa...a : Disk array name
[Measures] Check whether the disk array name hasn’t been changed. Specify the newest one.
iSM10200: comm error: client sc=<aaa>h
ec=<bbb...b>h
[Classification] NOTICE
[Explanation] It indicates that it failed to process the telegram receiving.
aaa : Code indicating location of error
bbb...b : Error code
[Measures] Check whether abnormalities have occurred in the configuring process on the
iSM server machine and restart the iSM server.
iSM10201: comm error: client sc=<aaa>h
ec=<bbb...b>h
[Classification] NOTICE
[Explanation] It indicates that it failed to process the telegram transmission.
aaa : Code indicating location of error
bbb...b : Error code
[Measures] Check whether abnormalities have occurred in the configuring process on the
iSM server machine and restart the iSM server.
Chapter 2 Message List
220
iSM10210: comm error: client sc=<aaa>h
ec=<bbb...b>h
[Classification] NOTICE
[Explanation] It indicates that the telegram message contained an abnormality.
aaa : Code indicating location of error
bbb...b : Error code
[Measures] Failed in communication process with iSM client. If it is a transient failure,
check whether abnormalities have occurred in the connection environment
between iSM server and iSM client and connect again. If there is no abnormality
in the connection environment, the iSM client may be one with old version.
Perform the version up of the iSM client and connect again.
iSM10220: sys error: client sc=<aaa>h
ec=<bbb...b>h
[Classification] ERROR
[Explanation] It indicates that it failed in system call when telegram sending/receiving.
aaa : Code indicating location of error
bbb...b : Error code
[Measures] Check whether abnormalities (such as insufficient memory) have occurred in the
operation environment of iSM server machine and restart the iSM server.
Chapter 2 Message List
221
iSM10302: command: <aaa...a>, <bbb...b>,
status=failed (<cc>h/<dd>h/<ee>h)
[Classification] INFO
[Explanation] It indicates that it failed in accessing the disk array (failure of SCSI protocol).
aaa...a : Command name
bbb...b : Disk array name
cc : Sense Key defined in SCSI specification
dd : Additional Sense Code defined in SCSI specification
ee : Additional Sense Code Qualifier defined in SCSI specification
[Measures] Check whether the configuration of disk array has been changed.
iSM10303: command: <aaa...a>, volume=
<bbbb>h <ccc...c>, status=failed
(<dd>h/<ee>h/<ff>h)
[Classification] INFO
[Explanation] It indicates that it failed in accessing the volume expressed in logical disk
number (failure of SCSI protocol).
aaa...a : Command name
bbbb : Logical disk number
ccc...c : Disk array name
dd : Sense Key defined in SCSI specification
ee : Additional Sense Code defined in SCSI specification
ff : Additional Sense Code Qualifier defined in SCSI specification
[Measures] Check whether the configuration of disk array has been changed.
Chapter 2 Message List
222
iSM10304: command: <aaa...a>,
<bbb...b>=<ccc...c> (<dddd>h)
<eee...e>, status=failed
(<ff>h/<gg>h/<hh>h)
[Classification] INFO
[Explanation] It indicates that it failed in accessing the volume expressed in logical disk name
(failure of SCSI protocol).
aaa...a : Command name
bbb...b : Volume classification
ccc...c : Logical disk name
dddd : Logical disk number
eee...e : Disk array name
ff : Sense Key defined in SCSI specification
gg : Additional Sense Code defined in SCSI specification
hh : Additional Sense Code Qualifier defined in SCSI specification
[Measures] Check whether the configuration of disk array has been changed.
iSM10305: command: <aaa...a>, <bbb...b>,
status=failed (ec=<ccc...c>)
[Classification] INFO
[Explanation] It indicates that it failed in accessing the disk array (failure except for SCSI
protocol).
aaa...a : Command name
bbb...b : Disk array name
ccc...c : Error code
[Measures] Check whether the configuration of disk array has been changed.
Chapter 2 Message List
223
iSM10306: command: <aaa...a>,
volume=<bbbb>h <ccc...c>,
status=failed (ec=<ddd...d>)
[Classification] INFO
[Explanation] It indicates that it failed in accessing the volume expressed in volume number
(failure except for SCSI protocol).
aaa...a : Command name
bbbb : Logical disk number
ccc...c : Disk array name
ddd...d : Error code
[Measures] Check whether the configuration of disk array has been changed.
iSM10307: command: <aaa...a>,
<bbb...b>=<ccc...c>(<dddd>h)
<eee...e>, status=failed(ec=<fff...f>)
[Classification] INFO
[Explanation] It indicates that it failed in accessing the volume expressed in logical disk name
(failure except for SCSI protocol).
aaa...a : Command name
bbb...b : Volume classification
ccc...c : Logical disk name
dddd : Logical disk number
eee...e : Disk array name
fff...f : Error code
[Measures] Check whether the configuration of disk array has been changed.
Chapter 2 Message List
224
iSM10308: command: <aaa...a>, mv=<bbb...b>
(<cccc>h) <ddd...d>, rv=<bbb...b>
(<cccc>h) <ddd...d>, status=failed
(<ee>h/<ff>h/<gg>h)
[Classification] INFO
[Explanation] It indicates that it failed in accessing the pair expressed in MV or RV (failure of
SCSI protocol).
aaa...a : Command name
bbb...b : Logical disk name
cccc : Logical disk number
ddd...d : Disk array name
ee : Sense Key defined in SCSI specification
ff : Additional Sense Code defined in SCSI specification
gg : Additional Sense Code Qualifier defined in SCSI specification
[Measures] Check whether the configuration of disk array has been changed.
iSM10309: command: <aaa...a>, mv=<bbb...b>
(<cccc>h) <ddd...d>, rv=<bbb...b>
(<cccc>h) <ddd...d>, status=failed
(ec=<eee...e>)
[Classification] INFO
[Explanation] It indicates that it failed in accessing the pair expressed in MV or RV (failure
except for SCSI protocol).
aaa...a : Command name
bbb...b : Logical disk name
cccc : Logical disk number
ddd...d : Disk array name
eee...e : Error code
[Measures] Check whether the configuration of disk array has been changed.
Chapter 2 Message List
225
iSM10310: command: <aaa...a>, <bbb...b>=
<ccc...c> (<dddd>h) <eee...e>
[Classification] NOTICE
[Explanation] It indicates that setting operation to volume expressed in logical disk name has
been executed.
aaa...a : Command name
bbb...b : Volume classification
ccc...c : Logical disk name
dddd : Logical disk number
eee...e : Disk array name
As for command name, refer to the “Data Replication User’s Manual (Function
Guide)”.
[Measures] Unnecessary
iSM10311: command: <aaa...a>, <bbb...b>
[Classification] NOTICE
[Explanation] It indicates that setting operation to disk array has been executed.
aaa...a : Command name
bbb...b : Disk array name
As for command name, refer to the “Data Replication User’s Manual (Function
Guide)”.
[Measures] Unnecessary
Chapter 2 Message List
226
iSM10312: command: <aaa...a>, mv=<bbb...b>
(<cccc>h) <ddd...d>, rv=<bbb...b>
(<cccc>h) <ddd...d>
[Classification] NOTICE
[Explanation] It indicates that setting operation to the pair expressed in MV or RV has been
executed.
aaa...a : Command name
bbb...b : Logical disk name
cccc : Logical disk number
ddd...d : Disk array name
As for command name, refer to the “Data Replication User’s Manual (Function
Guide)”.
[Measures] Unnecessary
iSM10313: Replication state of diskarray was
changed: <aaa...a>, Replication
Subsystem State = <bbb...b>, Back
Ground Copy Level = <c>
[, several states changed.]
[Classification] NOTICE
[Explanation] It indicates that the state change of disk array replication (freeze/defreeze) was
detected.
If two or more state transitions occurred within a polling interval and the midway
states could not be identified, “several states changed” is output to indicate that
multiple state transitions occurred.
aaa...a : Disk array name
bbb...b : Disk array state
freeze : Freeze
defreeze : Defreeze
c : Background copy level (1, 2, 3 , 4, 5)
1,2,3,4,5: Background copy level
[Measures] Unnecessary
Chapter 2 Message List
227
iSM10314: Logical Disks were paired:
mv=<aaa...a>(<bbbb>h) <ccc...c> ,
rv=<aaa...a>(<bbbb>h) <ccc...c>
[, several states changed.]
[Classification] NOTICE
[Explanation] It indicates that paired volumes were detected.
If two or more state transitions occurred within a polling interval and the midway
states could not be identified, “several states changed” is output to indicate that
multiple state transitions occurred.
aaa...a : Logical disk name
bbbb : Logical disk number
ccc...c : Disk array name
[Measures] Unnecessary
iSM10315: Logical Disks were unpaired:
mv=<aaa...a>(<bbbb>h) <ccc...c> ,
rv=<aaa...a>(<bbbb>h) <ccc...c>
[, several states changed.]
[Classification] NOTICE
[Explanation] It indicates that unpairing of paired volumes was detected.
If two or more state transitions occurred within a polling interval and the midway
states could not be identified, “several states changed” is output to indicate that
multiple state transitions occurred.
aaa...a : Logical disk name
bbbb : Logical disk number
ccc...c : Disk array name
[Measures] Unnecessary
Chapter 2 Message List
228
iSM10316: Replication state of pair was
changed: mv=<aaa...a>(<bbbb>h)
<ccc...c>, Activity State=<ddd...d>,
Sync State=<eee...e>, Copy Control
State=<fff...f>, rv=<aaa...a> (<bbbb>h)
<ccc...c>[, Activity State= <ddd...d>,
Sync State=<eee...e>, Copy Control
State=<fff...f>][,several states
changed.]
[Classification] NOTICE
[Explanation] It indicates that change of replication state (Replicate/Restore/Separate, etc.) of
paired volume was detected.
If two or more state transitions occurred within a polling interval and the midway
states could not be identified, “several states changed” is output to indicate that
multiple state transitions occurred. Both MV and RV were changed and the
two are under the same state, only one state is indicated for activity state, sync
state, and copy control state.
aaa...a : Logical disk name
bbbb : Volume number
ccc...c : Disk array name
ddd...d : Activity state
replicate : Replicate
separate : Separate
restore : Restore
restore(protect) : Restore with RV protection
eee...e : Sync state
rpl/exec : Replicate Execution(rpl/exec)
rpl/sync : Sync State(rpl/sync)
cancel : Forced Separate(cancel)
fault : Failure Separation(fault)
sep/exec : Separate Execution(sep/exec)
separated : Separated(separated)
rst/exec : Restore Execution(rst/exec)
rst/sync : Sync State(rst/sync)
Chapter 2 Message List
229
fff...f : Copy control state
normal suspend : Copy suspending
abnormal suspend : Copy fault suspending
background copy : Background copy
foreground(sync) : Foreground copy (synchronous)
foreground(semi) : Foreground copy (semi-synchronous)
Invalid : Invalid
[Measures] Unnecessary
iSM10317: command: <aaa...a>, LD=<bbb...b>
(<cccc>h) <ddd...d>, mode=<eee...e>
[Classification] NOTICE
[Explanation] It indicates that the command was executed.
aaa...a : Command name
bbb...b : Logical disk name
cccc : Logical disk number
ddd...d : Disk array name
eee...e : Mode
for aaa...a = mode change:
eee...e = <R/W Permit | Read Only | Not Ready >
for aaa...a = set restriction:
eee...e = <Available | Not Ready | Not Available >
for aaa...a = set state of rv data:
eee...e = <Valid | Invalid>
[Measures] Unnecessary
Chapter 2 Message List
230
iSM10318: Replication state of Logical Disk was
changed: LD=<aaa...a>(<bbbb>h)
<ccc...c>,
Restriction=<ddd...d> [,several states
changed.]
[Classification] NOTICE
[Explanation] It indicates that change of logical disk status was detected. If two or more state
transitions occurred within a polling interval and the midway states could not be
identified, “several states changed” is output to indicate that multiple state
transitions occurred.
aaa...a : Logical disk name
bbbb : Logical disk number
ccc...c : Disk array name
ddd...d : RV access restriction
< R/W Permit | Read Only | Not Ready | Not Available >
[Measures] Unnecessary
iSM10320: sys error: cmd sc=<aaa>h
ec=<bbb...b>h
[Classification] ERROR
[Explanation] It indicates that it failed in system call when access to disk array was processed.
aaa : Code indicating location of error
bbb...b : Error code
[Measures] Check whether abnormalities (such as insufficient memory) have occurred in the
operation environment of iSM server machine and restart the iSM server.
Chapter 2 Message List
231
iSM10321: command: <aaa...a>,
ATgroup=<bbb...b> <ccc...c> [,
classification=<ddd...d>][, New
ATgroup Name=<eee...e>][,
Mode=<fff...f>, Copy
Mode=<ggg...g>][,
Restriction=<hhh...h>]
[Classification] NOTICE
[Explanation] It indicates that a command related to AT-group was executed.
aaa...a : Name of the executed command
create ATgroup : AT-group creation
delete ATgroup : AT-group deletion
change ATgroup name : AT-group rename
change ATgroup attribute: Change AT-group attribute
ATgroup replicate : AT-group replicate
ATgroup separate : AT-group separate
ATgroup restore : AT-group restore
ATgroup forced delete : AT-group forced deletion
change ATgroup state : Using RV after failure separation
bbb...b : AT-group (concentrator) name
ccc...c : Disk array name
ddd...d : AT-group type
concentrator : Concentrator
distributor : Distributor
both : Both
eee...e : New AT-group (concentrator) name
fff...f : Atomic-break mode
MV Access Continue : MV access continue (auto
separate) mode
MV Access Stop : MV access stop (manual separate)
mode
Invalid : Invalid
ggg...g : Copy mode
synchronous copy : Foreground copy (synchronous)
semi synchronous copy : Foreground copy
(semi-synchronous)
background copy : Background copy
Chapter 2 Message List
232
hhh...h : RV access restriction
<R/W Permit | Read Only>
[Measures] Unnecessary
iSM10322: command: <aaa...a>,
ATgroup=<bbb...b> <ccc...c>,
LD=<ddd...d>(<eeee>h)
[Classification] NOTICE
[Explanation] It indicates that a command related to AT-group was executed.
aaa...a : Name of the executed command
enter volume for group : Add volume (pair) into
AT-group.
remove volume from group : Delete volume (pair) from
AT-group
bbb...b : AT-group (concentrator) name
ccc...c : Disk array name
ddd...d : Logical disk name
eeee : Logical disk number
[Measures] Unnecessary
Chapter 2 Message List
233
iSM10323: ATgroup created: ATgroup=<aaa...a>
<bbb...b>, classification=<ccc...c>,
Mode=<ddd...d>, Copy
Mode=<eee...e>, ATgroup State
=<fff...f>, Sync State=<ggg...g>,
Volume Number=<hhhh>[, several
states changed.]
[Classification] NOTICE
[Explanation] It indicates that an AT-group has been newly created.
aaa...a : AT-group (concentrator) name
bbb...b : Disk array name
ccc...c : AT-group type
concentrator : Concentrator
distributor : Distributor
ddd...d : Atomic-break mode
MV Access Continue : MV access continue (auto
separate) mode
MV Access Stop : MV access stop (manual separate)
mode
Invalid : Invalid
eee...e : Copy mode
synchronous copy : Foreground copy (synchronous)
semi synchronous copy : Foreground copy
(semi-synchronous)
background copy : Background copy
fff...f : AT-group consistency state
Non-atomic : Non-atomic state
Atomic : Atomic state
Invalid : Invalid
ggg...g : AT-group sync state
Sep/start : Separate start state
Sep/exec : Separate execution state
Fault : Failure separation state
Separated : Separated state
Rpl/start : Replicate start state
Rpl/exec : Replicate execution state
Rpl/sync : Replicate synchronous
Chapter 2 Message List
234
Rst/suspend : Restore suspend state
Invalid : Invalid
hhhh : Number of the registered volumes
[Measures] Unnecessary
iSM10324: ATgroup deleted: ATgroup=<aaa...a>
<bbb...b>, classification=<ccc...c>
[Classification] NOTICE
[Explanation] It indicates that an AT-group has been deleted.
aaa...a : AT-group (concentrator) name
bbb...b : Disk array name
ccc...c : AT-group type
concentrator : Concentrator
distributor : Distributor
[Measures] Unnecessary
Chapter 2 Message List
235
iSM10325: Replication state of ATgroup was
changed: ATgroup=<aaa...a>
<bbb...b>, classification=<ccc...c>[,
New ATgroup Name =<ddd...d>],
Mode=<eee...e>, Copy Mode=<fff...f>,
ATgroup State=<ggg...g>, Sync
State=<hhh...h>, Volume
number=<iiii>[, several states
changed.]
[Classification] NOTICE
[Explanation] It indicates that the state of an AT-group has been changed. If two or more
state transitions occurred within a polling interval and the midway states could
not be identified, “several states changed” is output to indicate that multiple state
transitions occurred.
aaa...a : AT-group (concentrator) name
bbb...b : Disk array name
ccc...c : AT-group type
concentrator : Concentrator
distributor : Distributor
ddd...d : New AT-group (concentrator) name
eee...e : Atomic-break mode
MV Access Continue : MV access continue (auto
separate) mode
MV Access Stop : MV access stop (manual separate)
mode
Invalid : Invalid
fff...f : Copy mode
synchronous copy : Foreground copy (synchronous)
semi synchronous copy : Foreground copy
(semi-synchronous)
background copy : Background copy
ggg...g : AT-group consistency state
Non-atomic : Non-atomic state
Atomic : Atomic state
Invalid : Invalid
hhh...h : AT-group sync state
Sep/start : Separate start state
Chapter 2 Message List
236
Separated : Separated state
Rpl/start : Replicate start state
Rpl/exec : Replicate execution state
Rpl/sync : Replicate synchronous
Rpl/suspend : Replicate suspend state
Rst/exec : Restore execution state
Rst/suspend : Restore suspend state
Invalid : Invalid
iiii : Number of the registered volumes
[Measures] Unnecessary
iSM10330: inconsistency of product revision of
diskarray: mv=<aaa...a>, rv=<aaa...a>
[Classification] NOTICE
[Explanation] There is a functionally unacceptable difference in the product revisions between
the disk arrays of MV and RV. It indicates that the process has been aborted
because replicate and restore will result in the inconsistency of the signatures on
the disks.
aaa...a : Disk array name
[Measures] Check the product revision of the disk array at the RV side, change it to the same
product revision as that of disk array at the MV side, then execute again.
Chapter 2 Message List
237
iSM10331: command: <aaa...a>,
ATgroup(concentrator)=<bbbb>h
<ccc...c> [<ddd...d>],
status=failed(<ee>h/<ff>h/<gg>h)
[Classification] INFO
[Explanation] It indicates that access to the concentrator indicated by the concentrator number
failed (SCSI protocol failure).
aaa...a : Command name
bbbb : AT-group (concentrator) number
ccc...c : Disk array name of AT-group (concentrator)
ddd...d : Disk array name of AT-group (distributor) (Output if fixed)
ee : Sense key defined according to SCSI specification
ff : Additional sense code defined according to SCSI specification
gg : Additional sense code qualifier defined according to SCSI
specification
[Measures] Check whether the disk array configuration is changed.
Chapter 2 Message List
238
iSM10332: command: <aaa...a>,
ATgroup(distributor)=<bbbb>h
<ccc...c> [<ddd...d>],
status=failed(<ee>h/<ff>h/<gg>h)
[Classification] INFO
[Explanation] It indicates that access to the distributor indicated by the distributor number
failed (SCSI protocol failure).
aaa...a : Command name
bbbb : AT-group (distributor) number
ccc...c : Disk array name of AT-group (distributor)
ddd...d : Disk array name of AT-group (concentrator)
ee : Sense key defined according to SCSI specification
ff : Additional sense code defined according to SCSI specification
gg : Additional sense code qualifier defined according to SCSI
specification
[Measures] Check whether the disk array configuration is changed.
iSM10333: command: <aaa...a>,
ATgroup(concentrator)=<bbbb>h
<ccc...c> [<ddd...d>],
status=failed(ec=<eee...e>)
[Classification] INFO
[Explanation] It indicates that access to the concentrator indicated by the concentrator number
failed (failure except for SCSI protocol).
aaa...a : Command name
bbbb : AT-group (concentrator) number
ccc...c : Disk array name of AT-group (concentrator)
ddd...d : Disk array name of AT-group (distributor) (Output if fixed)
eee...e : Error code indicating the type of abnormal state
[Measures] Check whether the disk array configuration is changed.
Chapter 2 Message List
239
iSM10334: command: <aaa...a>,
ATgroup(distributor)=<bbbb>h
<ccc...c> [<ddd...d>],
status=failed(ec=<eee...e>)
[Classification] INFO
[Explanation] It indicates that access to the distributor indicated by the distributor number
failed (failure except for SCSI protocol).
aaa...a : Command name
bbbb : AT-group (distributor) number
ccc...c : Disk array name of AT-group (distributor)
ddd...d : Disk array name of AT-group (concentrator)
eee...e : Error code indicating the type of abnormal state
[Measures] Check whether the disk array configuration is changed.
iSM10400: copy error:mv=<aaa...a>(<bbbb>h)
<ccc...c>, rv=<aaa...a>(<bbbb>h)
<ccc...c>, status=<ddd...d>h
[,ATgroup=<eee...e>][_ALERT_]
[Classification] ERROR
[Explanation] It indicates information of volume in which copy fault occurred.
For Windows, this message is target of ESMPRO Manager Report.
aaa...a : Logical disk name
bbbb : Logical disk number
ccc...c : Disk array name
ddd...d : Error code (4: fault separation, 9: abnormal suspend)
eee...e : AT-group (concentrator) name
[Measures] After remove cause of an error, restore the system with reference to description
about replication-specific HW fault in the “Data Replication User’s Manual
(Installation and Operation Guide for Windows)”.
Chapter 2 Message List
240
iSM10401: copy error:mv=<aaa...a>(<bbbb>h)
<ccc...c>, rv=<aaa...a>(<bbbb>h)
<ccc...c>, status=<ddd...d>h
[,ATgroup=<eee...e>] [UC=<fff...f>
FC=<gg>][_ALERT_]
[Classification] ERROR
[Explanation] It indicates the information of volume in which copy fault occurred.
For Windows, this message is target of ESMPRO Manager Report, and also to
be target of ALIVE/Express Report via ESMPRO.
aaa...a : Logical disk name
bbbb : Logical disk number
ccc...c : Disk array name
ddd...d : Error code (4: fault separation, 9: abnormal suspend)
eee...e : AT-group (concentrator) name
fff...f/gg : Maintenance information
[Measures] After remove cause of an error, restore the system with reference to description
about replication-specific HW fault in the “Data Replication User’s Manual
(Installation and Operation Guide for Windows)”.
Chapter 2 Message List
241
iSM10402: link error:Disk Array=<aaa...a>,
linkno=<bbb...b>, portno=<ccc...c>,
state=<ddd...d>h
[Classification] WARNING
[Explanation] It indicates that a fault, freeze, or checking state has occurred in the link between
disk arrays.
For Windows, this message is target of ESMPRO Manager Report.
aaa...a : Disk array name
bbb...b : Link number of RemoteDataReplication
ccc...c : Port number for link of RemoteDataReplication
ddd...d : Error code
2: Fault (link fault)
3: Freeze (The disk array to be connected to is in stop or freeze
state.)
4: Checking (Temporary link communication fault has been
detected.)
*If the checking state continues, it changes to the fault state.
[Measures] After remove cause of an error, restore the system with reference to description
about replication-specific HW fault in the “Data Replication User’s Manual
(Installation and Operation Guide for Windows)”.
Chapter 2 Message List
242
iSM10403: Disk array info (<aaa...a>
S/N=<bbb...b> Product-ID=<ccc...c>)
[UC=<ddd...d> FC=<ee>][_ALERT_]
[Classification] ERROR
[Explanation] It indicates additional information of disk array in which copy fault occurred.
For the pair composed by RemoteDataReplication, additional information of disk
array of each of MV and RV is output.
For Windows, this message is target of ESMPRO Manager Report, and also to
be target of ALIVE/Express Report via ESMPRO.
aaa...a : Disk array name
bbb...b : Serial number of disk array (16 characters)
ccc...c : Product ID of disk array (S2100 Disk Array etc)
ddd...d/ee : Maintenance information
[Measures] After remove cause of an error, restore the system with reference to description
about replication-specific HW fault in the “Data Replication User’s Manual
(Installation and Operation Guide for Windows)”.
iSM10410: comm error:report sc=<aaa>h,
ec=<bbb...b>h
[Classification] NOTICE
[Explanation] It indicates that telegram reception from iSM server failed.
aaa : Code indicating location of error
bbb...b : Error code
[Measures] Check whether abnormalities have occurred in the configuring process on the
iSM server.
Chapter 2 Message List
243
iSM10411: comm error:report event
type=<aaaaaaaa>h, ec=<bbb...b>h
[Classification] NOTICE
[Explanation] It indicates that it failed in receiving telegram from iSM server.
aaaaaaaa : Telegram code which indicates the telegram that occurred
abnormality
bbb...b : Error code
[Measures] Check whether abnormalities have occurred in the configuring process on the
iSM server.
iSM10420: comm error:report sc=<aaa>h,
ec=<bbb...b>h
[Classification] NOTICE
[Explanation] It indicates that it failed in sending telegram to iSM server.
aaa : Code indicating location of error
bbb...b : Error code
[Measures] Check whether abnormalities have occurred in the configuring process on the
iSM server.
iSM10430: sys error:report sc=<aaa>h,
ec=<bbb...b>h
[Classification] ERROR
[Explanation] It indicates that it failed in system call when a trouble report to iSM client.
aaa : Code indicating location of error
bbb...b : Error code
[Measures] Check whether abnormalities (such as insufficient memory) have occurred in the
operation environment of iSM server machine and restart the iSM server.
Chapter 2 Message List
244
iSM10440: func error:report sc=<aaa>h,
ec=<bbb...b>h
[Classification] NOTICE
[Explanation] It indicates that it failed in the transmission of trouble report to iSM client.
aaa : Code indicating location of error
bbb...b : Error code
[Measures] Check whether abnormalities have occurred in the configuring process on the
iSM server.
iSM10501: command option
error:option=<aaaaaa>,
status=<bbb...b>
[Classification] ERROR
[Explanation] It indicates that trouble occurred in the specified option.
aaaaaa : Option
<array | format | file | atg | csv>
bbb...b : Detail status
[Measures] Check the option specification and re-execute.
iSM10502: command not
execute:status=<aaa...a>
[Classification] ERROR
[Explanation] It indicates that the command execution environment was not prepared.
aaa...a : Execution environment status
[Measures] Check the command execution environment and re-execute.
Chapter 2 Message List
245
iSM10503: array state error:status=<aaa...a>
[Classification] ERROR
[Explanation] It indicates that it failed to refer to information due to the device status.
aaa...a : Device status
[Measures] Check the device status and re-execute.
iSM10504: acquire information error:status=<a>
[Classification] ERROR
[Explanation] It indicates that it failed to obtain information.
a : Detail code
[Measures] Check the system resource and re-execute.
iSM10505: data output file error:action=<aaaaa>,
status=<bbb...b>
[Classification] ERROR
[Explanation] It indicates that it failed to output information in a file.
aaaaa : Execution process
<open | write>
bbb...b : Detail status
[Measures] Check whether the directory exists and authority to write is given, and
re-execute.
Chapter 2 Message List
246
iSM10900: Process is busy when it terminates
emergency. Unexpected error
message maybe generated.
[Classification] WARNING
[Explanation] It indicates that the replication management received a request for emergency
stop, but could not terminate the process immediately.
[Measures] Unnecessary
Chapter 2 Message List
247
iSM11000 ∼
iSM11100: Command completed successfully.
[Classification] INFO
[Explanation] Command execution succeeded.
[Measures] Unnecessary
iSM11101: Setup of the Disk Array Subsystem is
done according to specified
parameter. (<aaa...a>)
[Classification] INFO
[Explanation] Setting of the disk array is executed according to the specified parameter.
aaa...a : Additional information
[Measures] Unnecessary
iSM11102: Specified Disk Array Subsystem is
not monitored. (fault,maintenance)
[Classification] INFO
[Explanation] Specified disk array is not being monitored (fault, maintenance).
[Measures] Execute again after fault recovery or after completion of maintenance work.
Chapter 2 Message List
248
iSM11103: Specified Disk Array Subsystem is
monitored by iSM. (Under processing
to stop monitoring.. )
[Classification] INFO
[Explanation] Specified disk array is being monitored by iSM server though monitoring stop
process is being executed.
[Measures] Stop monitoring disk array and execute it again.
iSM11104: Disk Array Subsystem ‘<aaa...a>’ was
selected.
[Classification] INFO
[Explanation] The Disk Array “aaa...a” has been selected.
aaa...a : Disk array name
[Measures] Unnecessary
iSM11105: Specified Disk Array Subsystem is
set by another maintenance tool.
[Classification] INFO
[Explanation] Specified disk array is set by another maintenance tool.
[Measures] Execute it again after the termination of maintenance operation with another
maintenance tool.
Chapter 2 Message List
249
iSM11106: The start of the configuration
operation was notified to Disk Array
Subsystem.
[Classification] INFO
[Explanation] Start of configuration operation was notified to the disk array.
[Measures] Unnecessary
iSM11107: The end of the configuration
operation was notified to Disk Array
Subsystem.
[Classification] INFO
[Explanation] The end of configuration operation was notified to a disk array.
[Measures] Unnecessary
iSM11108: <aaa...a> was started.
[Classification] INFO
[Explanation] aaa...a (iSMconf,iSMautobind) was started.
aaa...a : Program name
[Measures] Unnecessary
Chapter 2 Message List
250
iSM11109: <aaa...a> was terminated.
[Classification] INFO
[Explanation] aaa...a (iSMconf,iSMautobind) was terminated.
aaa...a : Program name
[Measures] Unnecessary
iSM11110: Command completed abnormally.
[Classification] INFO
[Explanation] With “All information” option selected, failed in obtaining (a part of)
information about disk array.
[Measures] Check the status of the disk array.
iSM11151: Failed to get information or set
configuration. (<aaa...a>)
[Classification] INFO
[Explanation] It failed in getting information or in setting configuration of the disk array.
aaa...a : Additional information
[Measures] Check whether the disk array is a monitoring object of iSM.
iSM11152: Failed to output Log Message.
[Classification] INFO
[Explanation] It failed in outputting log message.
[Measures] Check whether iSMsvr has been started.
Chapter 2 Message List
251
iSM11153: Cannot establish the communication
path.
[Classification] INFO
[Explanation] Communication pass cannot be established.
[Measures] Check whether iSMsvr has started.
iSM11154: Failed to request notification for start
of <aaa...a>.
[Classification] INFO
[Explanation] It failed in notifying the request for start of aaa...a.
aaa...a : Program name
[Measures] Check whether iSMsvr has started.
iSM11155: Failed to request notification for
termination of <aaa...a>.
[Classification] INFO
[Explanation] It failed in notifying the request for end of aaa...a.
aaa...a : Program name
[Measures] Check whether iSMsvr has started.
iSM11161: Failed to get Disk Array Subsystem
list.
[Classification] INFO
[Explanation] It failed in getting the disk array list.
[Measures] Check whether iSMsvr has started.
Chapter 2 Message List
252
iSM11162: Disk Array Subsystem which can be
operated by this program is not
found.
[Classification] INFO
[Explanation] No such disk array as is an object of support of iSM can be found.
[Measures] Terminate the program. Check that the iSM server covers the disk array as
monitoring target, and also check the environmental definition of the iSM server
and the connection with the disk array. For more information, refer to Part III
“Operations” in the “User’s Manual”.
iSM11163: Specified Disk Array Subsystem is
not found.
[Classification] INFO
[Explanation] The specified disk array cannot be found.
[Measures] Terminate the program. Check that the iSM server covers the disk array as
monitoring target, and also check the environmental definition of the iSM server
and the connection with the disk array. For more information, refer to Part III
“Operations” in the “User’s Manual”.
iSM11164: Specified Disk Array Subsystem is
not supported.
[Classification] INFO
[Explanation] The specified disk array is not supported.
[Measures] Check whether Disk array name is correct and that the specified disk array is the
object disk array.
Chapter 2 Message List
253
iSM11171: PD group doesn’t exist.
[Classification] INFO
[Explanation] PD group does not exist.
[Measures] Check the status of the disk array.
iSM11172: RANK doesn’t exist.
[Classification] INFO
[Explanation] RANK does not exist
[Measures] Check the status of the disk array.
iSM11173: LD doesn’t exist.
[Classification] INFO
[Explanation] LD does not exist.
[Measures] Check the status of the disk array.
iSM11174: PD doesn’t exist.
[Classification] INFO
[Explanation] PD does not exist.
[Measures] Check the status of the disk array.
Chapter 2 Message List
254
iSM11175: PORT doesn’t exist.
[Classification] INFO
[Explanation] PORT does not exist.
[Measures] Check the status of the disk array.
iSM11176: Permitted PORT for LD doesn’t exist.
[Classification] INFO
[Explanation] Port with access permission (to LD) does not exist.
[Measures] Check the status of the disk array.
iSM11178: LD Set doesn’t exist.
[Classification] INFO
[Explanation] There is no LD Set.
[Measures] Check the status of the disk array.
iSM11179: LD Set doesn’t match.
[Classification] INFO
[Explanation] LD Set does not match.
[Measures] Check the status of the disk array.
Chapter 2 Message List
255
iSM11180: Specified option is not supported by
specified disk array subsystem.
[Classification] INFO
[Explanation] The specified option is not supported by the specified disk array.
[Measures] Specify a disk array which supports the information of the specified option.
iSM11182: Pool doesn’t exist.
[Classification] INFO
[Explanation] Pool does not exist.
[Measures] Check the state of the disk array.
iSM11183: Snapshot Pool doesn’t exist.
[Classification] INFO
[Explanation] Pool does not exist.
[Measures] Check the state of the disk array.
iSM11184: Snapshot LD doesn’t exist.
[Classification] INFO
[Explanation] LD does not exist.
[Measures] Check the state of the disk array.
Chapter 2 Message List
256
iSM11220: Port #<aa>h-<bb>h was selected.
[Classification] INFO
[Explanation] Port aa-bb was selected.
aa-bb : Port number
[Measures] Unnecessary
iSM11221: View Host Permit List was selected.
[Classification] INFO
[Explanation] View host permit list was selected.
[Measures] Unnecessary
iSM11222: View LD Assign List was selected.
[Classification] INFO
[Explanation] View LD assign list was selected.
[Measures] Unnecessary
iSM11230: Access Control is not supported.
[Classification] INFO
[Explanation] Access control is not being supported.
[Measures] Check the status of the disk array.
Chapter 2 Message List
257
iSM11231: Port configuration is required.
[Classification] INFO
[Explanation] Port configuration is needed.
[Measures] Execute it after selecting the port.
iSM11232: Cannot set Access Control function.
Cross call function should be
working for using Access Control
function. It is set up from the main
menu.
[Classification] INFO
[Explanation] Access Control function cannot be set. Cross Call function must work when
using Access Control function. Cross Call function is set from main menu.
[Measures] Set the Cross Call function from main menu.
iSM11233: Not Port Extended Mode.
[Classification] INFO
[Explanation] It is not the port extended mode.
[Measures] Unnecessary
Chapter 2 Message List
258
iSM11234: Corresponding LD is not found.
[Classification] INFO
[Explanation] Corresponding LD cannot be found.
[Measures] Check the status of the disk array.
iSM11235: Effective LD without being in List.
[Classification] INFO
[Explanation] A nonexistent logical disk was specified.
[Measures] Specify a logical disk that exists.
iSM11236: Setting over this ineffective.
[Classification] INFO
[Explanation] Setting is invalid because the allowed number of assigned logical disks was
exceeded.
[Measures] Reduce the number of assigned logical disks, and then retry command execution.
iSM11237: Selected port is not supported
because protocol is difference.
[Classification] INFO
[Explanation] This program does not support selected port due to wrong protocol.
[Measures] Select a port that is supported by this program.
Chapter 2 Message List
259
iSM11240: PDG #<aa>h was selected.
[Classification] INFO
[Explanation] PDG aa was selected.
aa : PDG number
[Measures] Unnecessary
iSM11241: Cannot set up LD, because number
of PD is not sufficient.
[Classification] INFO
[Explanation] LD cannot be set because the number of PD is insufficient.
[Measures] Check the status of the disk array.
iSM11242: All settings are cleared.
[Classification] INFO
[Explanation] All settings are cleared.
[Measures] Unnecessary
iSM11250: Cannot execute Autobind, because
LD has already been bound.
[Classification] INFO
[Explanation] Autobind cannot be executed, because LD has already been bound.
[Measures] Please obey the instruction in the following message and go on the operation.
Chapter 2 Message List
260
iSM11251: Failed to open a file.
[Classification] INFO
[Explanation] It failed in opening a file.
[Measures] Check the content of the file.
iSM11252: Succeeded in loading a file.
[Classification] INFO
[Explanation] It succeeded in loading a file.
[Measures] Unnecessary
iSM11253: Illegal file parameter.
[Classification] INFO
[Explanation] File parameter is invalid.
[Measures] Check the content of the file.
iSM11255: Cannot bind LD by specified
parameter.
[Classification] INFO
[Explanation] LD cannot be bound by the specified parameter.
[Measures] Check the status of the disk array.
Chapter 2 Message List
261
iSM11257: Succeeded in saving a file.
[Classification] INFO
[Explanation] It succeeded in saving a file.
[Measures] Unnecessary
iSM11258: Failed to save a file.
[Classification] INFO
[Explanation] It failed in saving a file.
[Measures] Check whether the specification of the file name and the save destination are
correct.
iSM11300: This program configures Disk Array
Subsystem.
[Classification] INFO
[Explanation] This program configures disk array.
[Measures] Unnecessary
Chapter 2 Message List
262
iSM11305: IMPORTANT NOTICE: Stop IO access
to this Disk Array Subsystem from
the host before executing this
command which has parameter of
“all” or “High Reliability Mode : off”.
Otherwise the data in LD may be
destroyed.
[Classification] INFO
[Explanation] IMPORTANT NOTICE: Stop accessing to this disk array from the host before
executing this command which has the parameter of [all] or [High Reliability
Mode:off]. Otherwise, the data in LD may be invalid.
[Measures] Unnecessary
iSM11306: ATTENTION: Specified F/W is older
than Disk Array Subsystem’s F/W.
[Classification] INFO
[Explanation] Attention: Specified F/W is older than F/W of the disk array.
[Measures] Check whether F/W file revision is correct.
iSM11307: ATTENTION: Data in RANK will be
deleted.
[Classification] INFO
[Explanation] Attention: Data in RANK will be deleted.
[Measures] Unnecessary
Chapter 2 Message List
263
iSM11308: ATTENTION: PD Recovery History
data will be deleted.
[Classification] INFO
[Explanation] Attention: PD Recovery History data will be deleted.
[Measures] Unnecessary
iSM11309: ATTENTION: Internal Log data will be
deleted.
[Classification] INFO
[Explanation] ATTENTION: Internal Log data will be deleted.
[Measures] Unnecessary
iSM11310: ATTENTION: Media Error List data
will be deleted.
[Classification] INFO
[Explanation] Attention: Media Error List data will be deleted.
[Measures] Unnecessary
iSM11311: ATTENTION: Need to reboot the OS
to enable the setting.
[Classification] INFO
[Explanation] Attention: Rebooting the operation system is needed to enable the setting.
[Measures] Unnecessary
Chapter 2 Message List
264
iSM11320: LD capacity which is bound will be
<aa> MB.
[Classification] INFO
[Explanation] LD capacity which is bound will become aa MB.
aa : LD capacity
[Measures] Unnecessary
iSM11321: System space of 2MB is added to LD,
and LD is bound.
[Classification] INFO
[Explanation] System space of 2MB is added to LD, and LD is bound.
[Measures] Unnecessary
iSM11322: The address which can be specified
is “<aaaa>h” or “<bbbb>h”.
[Classification] INFO
[Explanation] The address which can be specified is aaaa or bbbb.
aaaa/bbbb : Address which can be specified
[Measures] Unnecessary
Chapter 2 Message List
265
iSM11323: Cannot bind LD by specified RANK.
(unsupported RAID type/unsupported
stripe size)
[Classification] INFO
[Explanation] LD cannot be bound in the specified RANK (unsupported RAID
type/unsupported stripe size).
[Measures] Check the status of RANK.
iSM11330: Failed to get Disk Array Subsystem
information.
[Classification] INFO
[Explanation] It failed in getting the information of disk array.
[Measures] Check the status of the disk array.
iSM11340: Now downloading. Please wait a
minute.
[Classification] INFO
[Explanation] Now downloading. Wait a minute.
[Measures] Unnecessary
iSM11360: Specified resource is not found.
[Classification] INFO
[Explanation] Specified resource cannot be found.
[Measures] Check the status of the disk array.
Chapter 2 Message List
266
iSM11361: Specified LD is not found.
[Classification] INFO
[Explanation] Specified LD cannot be found.
[Measures] Check the status of the disk array.
iSM11362: Failed to bind RANK.
[Classification] INFO
[Explanation] It failed in binding RANK.
[Measures] Check the status of the disk array.
iSM11363: Failed to bind some RANKs.
[Classification] INFO
[Explanation] It failed in binding some RANKs.
[Measures] Check the status of the disk array.
iSM11364: Failed to bind Hot Spare.
[Classification] INFO
[Explanation] It failed in binding Hot Spare.
[Measures] Check the status of the disk array.
Chapter 2 Message List
267
iSM11365: Specified PD doesn’t exist.
[Classification] INFO
[Explanation] Specified PD does not exist.
[Measures] Check the status of the disk array.
iSM11366: Specified RANK doesn’t exist.
[Classification] INFO
[Explanation] Specified RANK does not exist.
[Measures] Check the status of the disk array.
iSM11367: Specified Hot Spare doesn’t exist.
[Classification] INFO
[Explanation] Specified Hot spare does not exist.
[Measures] Check the status of the disk array.
iSM11369: Specified F/W file is not conformable
to the target Disk Array.
[Classification] INFO
[Explanation] Specified F/W file is not conformable to the object disk array.
[Measures] Check whether F/W file is correct.
Chapter 2 Message List
268
iSM11370: Failed to read F/W file.
[Classification] INFO
[Explanation] It failed in reading F/W file.
[Measures] Check whether the path and name of specified F/W file is normal.
iSM11372: Disk Array Subsystem is not found.
[Classification] INFO
[Explanation] Disk array cannot be found.
[Measures] Check whether it is the monitoring object of iSM.
iSM11373: Specified F/W file is not conformable
to the target resource F/W.
[Classification] INFO
[Explanation] Specified F/W file is not conformable to the object resource.
[Measures] Check whether F/W file is correct.
iSM11374: <a> RANKs were bound successfully.
But some RANKs failed to bind.
[Classification] INFO
[Explanation] It succeeded to bind “a” number of RANKs, but it failed in binding some
RANKs.
a : Number of RANKs that succeeded to bind.
[Measures] Check the status of the disk array.
Chapter 2 Message List
269
iSM11375: The directory may have been deleted
or changed. Please specify file
name by absolute path.
[Classification] INFO
[Explanation] The directory may have been deleted or changed. Specify the file name by
absolute path.
[Measures] Unnecessary
iSM11376: Cannot bind LD, because number of
LD exceeds the range that can be
specified.
[Classification] INFO
[Explanation] LD cannot be bound, because number of LDs exceeds the range that can be
specified.
[Measures] Input number of LD correctly.
iSM11377: Cannot bind LD, because LD number
of LD exceeds the range that can be
specified. Only <aa> LDs will be able
to be bound.
[Classification] INFO
[Explanation] LD cannot be bound, because number of LDs exceeds the range that can be
specified. Only aa LDs will be able to be bound.
aa : Number of LD which can be bound
[Measures] Input number of LD correctly.
Chapter 2 Message List
270
iSM11378: Not enough space to bind LD.
[Classification] INFO
[Explanation] Space to bind LD is insufficient.
[Measures] Check the space of RANK.
iSM11379: Not enough space to bind LD. Only
<aa> LDs be able to be bound.
[Classification] INFO
[Explanation] Space to bind LD is insufficient. Only aa number of LDs will be able to be
bound.
aa : Number of LD which can be bound
[Measures] Check the space of RANK.
iSM11380: Failed to allocate a memory space.
[Classification] INFO
[Explanation] It failed in allocating a memory space.
[Measures] Check the status of the server.
iSM11381: Failed to bind LD.
[Classification] INFO
[Explanation] It failed in binding LD.
[Measures] Check the status of RANK.
Chapter 2 Message List
271
iSM11382: <aa> LDs was bound successfully.
But some LDs failed to bind.
[Classification] INFO
[Explanation] It succeeded to bind aa number of LDs, but it failed in binding some LDs.
aa : Number of LD which has already been bound
[Measures] Check the status of RANK.
iSM11383: Succeeded in downloading of the
following <aaa...a>. <bbbb>(hex) :<cc,
cc>
[Classification] INFO
[Explanation] It succeeded in downloading of the following aaa...a
aaa...a : Download resource name
bbbb : Resource number
cc, cc : Resource position
[Measures] Unnecessary
iSM11384: Failed to download F/W of <aaa...a>.
[Classification] INFO
[Explanation] It failed in downloading aaa...a.
aaa...a : Download resource name
[Measures] Check whether F/W file is normal.
Chapter 2 Message List
272
iSM11385: The following <aaa...a> didn’t
download.
[Classification] INFO
[Explanation] The following aaa...a was not downloaded.
aaa...a : Download resource name
[Measures] Check the status of the disk array and download only the unexecuted one.
iSM11402: Auto assignment was selected.
(<aaa...a>)
[Classification] INFO
[Explanation] Auto assignment was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11403: Subsystem time (specifying time)
was selected.
[Classification] INFO
[Explanation] Subsystem time (specifying time) was selected.
[Measures] Unnecessary
iSM11404: Subsystem time (using os time) was
selected.
[Classification] INFO
[Explanation] Subsystem time (using os time) was selected.
[Measures] Unnecessary
Chapter 2 Message List
273
iSM11405: Cannot bind SPARE by specified
parameter. (<aaa...a>)
[Classification] INFO
[Explanation] SPARE cannot be bound by specified parameter.
aaa...a : Additional information
[Measures] Check whether the input parameter is correct.
iSM11406: Cannot bind RANK by specified
parameter. (<aaa...a>)
[Classification] INFO
[Explanation] RANK cannot be bound by specified parameter.
aaa...a : Additional information
[Measures] Check whether the input parameter is correct.
iSM11407: LD format time was selected.
[Classification] INFO
[Explanation] LD format time was selected.
[Measures] Unnecessary
iSM11408: RANK rebuilding was selected.
(<aaa...a>)
[Classification] INFO
[Explanation] RANK rebuilding was selected.
aaa...a : Additional information
[Measures] Unnecessary
Chapter 2 Message List
274
iSM11409: Cross call was selected. (<aaa...a>)
[Classification] INFO
[Explanation] Cross call was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11410: Subsystem control mode was
selected. (<aaa...a>)
[Classification] INFO
[Explanation] Subsystem control mode was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11412: Expand lun was selected.(<aaa...a>)
[Classification] INFO
[Explanation] Expand LUN was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11413: Illegal firmware file size.
[Classification] INFO
[Explanation] Firmware file size is incorrect.
[Measures] Check whether the firmware file is correct.
Chapter 2 Message List
275
iSM11414: Cannot open a firmware file.
[Classification] INFO
[Explanation] Firmware file cannot be opened.
[Measures] Check whether the path and name of the firmware file is correct.
iSM11415: Illegal resource type was selected.
[Classification] INFO
[Explanation] Selected resource is incorrect.
[Measures] Check whether the firmware file belongs to a target resource.
iSM11416: Firmware download was selected.
(<aaa...a>)
[Classification] INFO
[Explanation] Firmware download was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11417: Target PD doesn’t exist in specified
Disk Array Subsystem.
[Classification] INFO
[Explanation] Object PD does not exist in specified disk array.
[Measures] Check the status of the disk array.
Chapter 2 Message List
276
iSM11419: Target Disk Array Subsystem
specified by firmware file is not
found.
[Classification] INFO
[Explanation] Object disk array specified by firmware file is not found.
[Measures] Check whether the firmware file belongs to a target disk array.
iSM11420: Cannot bind some RANKs that was
specified. (<aaa...a>)
[Classification] INFO
[Explanation] Some RANKs that was specified cannot be bound.
aaa...a : Additional information
[Measures] Check the status of the disk array.
iSM11421: Forced reduce rebuilding was
selected. (<aaa...a>)
[Classification] INFO
[Explanation] Forced reduce rebuilding was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11422: Internal log init was selected.
[Classification] INFO
[Explanation] Internal log init was selected.
[Measures] Unnecessary
Chapter 2 Message List
277
iSM11423: Hot SPARE bind custom was
selected. (<aaa...a>)
[Classification] INFO
[Explanation] Hot spare bind custom was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11424: Hot SPARE bind standard was
selected. (<aaa...a>)
[Classification] INFO
[Explanation] Hot spare bind standard was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11425: Hot SPARE unbind was selected.
(<aaa...a>)
[Classification] INFO
[Explanation] Hot spare unbind was selected.
aaa...a : Additional information
[Measures] Unnecessary
Chapter 2 Message List
278
iSM11426: LD unbind was selected. (<aaa...a>)
[Classification] INFO
[Explanation] LD unbind was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11429: RANK is not found in specified PDG.
(<aaa...a>)
[Classification] INFO
[Explanation] RANK is not found in the specified PDG.
aaa...a : Additional information
[Measures] Check the status of the disk array.
iSM11431: Auto repair was selected. (<aaa...a>)
[Classification] INFO
[Explanation] Auto repair was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11438: Cannot execute with specified RANK
capacity.
[Classification] INFO
[Explanation] It cannot be executed with specified RANK capacity.
[Measures] Check whether the input parameter is correct.
Chapter 2 Message List
279
iSM11439: LD ownership was selected.
(<aaa...a>)
[Classification] INFO
[Explanation] LD ownership was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11440: Dynamic capacity expansion was
selected. (<aaa...a>)
[Classification] INFO
[Explanation] Dynamic capacity expansion was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11442: RANK bind custom was selected.
(<aaa...a>)
[Classification] INFO
[Explanation] RANK bind custom was selected.
aaa...a : Additional information
[Measures] Unnecessary
Chapter 2 Message List
280
iSM11443: RANK bind standard was selected.
(<aaa...a>)
[Classification] INFO
[Explanation] RANK bind standard was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11444: RANK unbind was selected.
(<aaa...a>)
[Classification] INFO
[Explanation] RANK unbind was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11455: Temp. sense interval was selected.
[Classification] INFO
[Explanation] Temp. sense interval was selected.
[Measures] Unnecessary
iSM11486: Failed to execute the firmware
download. (<aaa...a>)
[Classification] INFO
[Explanation] It failed in downloading the firmware.
aaa...a : Additional information
[Measures] Check whether the F/W file is normal.
Chapter 2 Message List
281
iSM11487: The resource that F/W is downloaded
to may be not present. (<aaa...a>)
[Classification] INFO
[Explanation] The resource of downloading destination may be not mounted.
aaa...a : Additional information
[Measures] Check the status of the disk array.
iSM11501: LD information was selected.
[Classification] INFO
[Explanation] “LD information” was selected.
[Measures] Unnecessary
iSM11502: LD No./Name information was
selected.
[Classification] INFO
[Explanation] “LD Number./Name information” was selected.
[Measures] Unnecessary
iSM11503: RANK information was selected.
[Classification] INFO
[Explanation] “RANK information” was selected.
[Measures] Unnecessary
Chapter 2 Message List
282
iSM11504: RANK/PD information was selected.
[Classification] INFO
[Explanation] “RANK/PD information” was selected.
[Measures] Unnecessary
iSM11505: PD information was selected.
[Classification] INFO
[Explanation] “PD information” was selected.
[Measures] Unnecessary
iSM11506: RANK map information was selected.
[Classification] INFO
[Explanation] “RANK map information” was selected.
[Measures] Unnecessary
iSM11507: PD recovery history init. was
selected.
[Classification] INFO
[Explanation] “PD recovery history report init.” was selected.
[Measures] Unnecessary
Chapter 2 Message List
283
iSM11508: Media error list init. was selected.
[Classification] INFO
[Explanation] “Median error list init.” was selected.
[Measures] Unnecessary
iSM11509: Subsystem view current setting was
selected.
[Classification] INFO
[Explanation] “Subsystem view current setting” was selected.
[Measures] Unnecessary
iSM11510: Maintenance view current setting was
selected.
[Classification] INFO
[Explanation] “Maintenance view current setting” was selected.
[Measures] Unnecessary
iSM11521: PD recovery history doesn’t exist.
[Classification] INFO
[Explanation] “PD recovery history” does not exist.
[Measures] Unnecessary
Chapter 2 Message List
284
iSM11522: Media error list doesn’t exist.
[Classification] INFO
[Explanation] Media Error List does not exist.
[Measures] Unnecessary
iSM11531: Disk Array Subsystem list
information option was selected.
[Classification] INFO
[Explanation] “Disk Array Subsystem list information” option was selected.
[Measures] Unnecessary
iSM11532: Disk Array Subsystem detail
information option was selected.
(<aaa...a>)
[Classification] INFO
[Explanation] “Disk Array Subsystem detail information” option was selected.
aaa...a : Additional information
[Measures] Unnecessary
Chapter 2 Message List
285
iSM11533: LD list information option was
selected. (<aaa...a>)
[Classification] INFO
[Explanation] “LD list information” option was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11534: LD detail information option was
selected. (<aaa...a>)
[Classification] INFO
[Explanation] “LD detail information” option was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11535: PD list information option was
selected. (<aaa...a>)
[Classification] INFO
[Explanation] “PD list information” option was selected.
aaa...a : Additional information
[Measures] Unnecessary
Chapter 2 Message List
286
iSM11536: PD detail information option was
selected. (<aaa...a>)
[Classification] INFO
[Explanation] “PD detail information” option was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11537: Port information with LD key option
was selected. (<aaa...a>)
[Classification] INFO
[Explanation] “Port information with LD key” option was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11538: LD information with port key option
was selected. (<aaa...a>)
[Classification] INFO
[Explanation] “LD information with port key” option was selected.
aaa...a : Additional information
[Measures] Unnecessary
Chapter 2 Message List
287
iSM11539: Controller information option was
selected. (<aaa...a>)
[Classification] INFO
[Explanation] “Controller information” option was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11540: Enclosure information option was
selected. (<aaa...a>)
[Classification] INFO
[Explanation] “Enclosure information” option was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11542: Enclosure resource doesn’t exist.
(<aaa...a>)
[Classification] INFO
[Explanation] Enclosure resource does not exist.
aaa...a : Additional information
[Measures] Unnecessary
Chapter 2 Message List
288
iSM11543: Port information option was selected.
(<aaa...a>)
[Classification] INFO
[Explanation] “Platform information” option was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11544: Specified Resource does not exist.
[Classification] INFO
[Explanation] Specified resource does not exist.
[Measures] Check input resource name and resource number, and retry processing.
iSM11545: Cache doesn’t exist.
[Classification] INFO
[Explanation] Cache module does not exist.
[Measures] Unnecessary
iSM11546: Cache segment does not exist.
[Classification] INFO
[Explanation] Cache segment does not exist.
[Measures] Check the status of the disk array.
Chapter 2 Message List
289
iSM11548: Volume list data is not found.
[Classification] ERROR
[Explanation] A volume list data does not exist or specified volume does not exist in the
volume list data.
[Measures] Check a volume name with reference to the volume list data, and input the
volume name again. If a volume table is not displayed, create a volume list.
iSM11549: Cannot make or refresh volume list
data.
[Classification] ERROR
[Explanation] Creation of a volume list data failed.
This message is output on UNIX system.
[Measures] If operation trace data has been collected, troubleshoot on the basis of operation
trace data and error code, and then remove cause of fault.
iSM11557: Only root can use this option.
[Classification] ERROR
[Explanation] A command was executed by a user other than root user or privileged user.
This message is output on UNIX system.
[Measures] Execute the command by a root user or a privileged user.
Chapter 2 Message List
290
iSM11561: Rebuild option was selected.
(<aaa...a>)
[Classification] INFO
[Explanation] “Rebuild” option was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11562: Spare Rebuild option was selected.
(<aaa...a>)
[Classification] INFO
[Explanation] “Spare Rebuild” option was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11563: iSMrepair was executed.
[Classification] INFO
[Explanation] iSMrepair was executed.
[Measures] Unnecessary
iSM11564: PD Group Number was too large.
[Classification] INFO
[Explanation] PD Group number exceeds the range that can be specified.
[Measures] Check whether the input parameter is correct.
Chapter 2 Message List
291
iSM11565: PD Number was too large.
[Classification] INFO
[Explanation] PD number exceeds the range that can be specified.
[Measures] Check whether the input parameter is correct.
iSM11566: RANK Number was too large.
[Classification] INFO
[Explanation] RANK number exceeds the range that can be specified.
[Measures] Check whether the input parameter is correct.
iSM11567: PD Group Number is different.
[Classification] INFO
[Explanation] PD Group Number is different.
[Measures] Check whether the input parameter is correct.
iSM11568: RANK list information option was
selected.
[Classification] INFO
[Explanation] “RANK list information” option was selected.
[Measures] Unnecessary
Chapter 2 Message List
292
iSM11569: RANK detail information option was
selected.
[Classification] INFO
[Explanation] “RANK detail information” option was selected.
[Measures] Unnecessary
iSM11570: Access Control list information
option was selected.
[Classification] INFO
[Explanation] “Access Control list information” option was selected.
[Measures] Unnecessary
iSM11571: LD Set information with LD Set key
option was selected.
[Classification] INFO
[Explanation] “LD Set information” option was selected.
[Measures] Unnecessary
Chapter 2 Message List
293
iSM11572: All information option was selected.
[Classification] INFO
[Explanation] “All information” option was selected.
[Measures] Unnecessary
iSM11573: Controller detail information option
was selected. (<aaa...a>)
[Classification] INFO
[Explanation] “Controller detail information” option was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11574: Enclosure detail information option
was selected. (<aaa...a>)
[Classification] INFO
[Explanation] “Enclosure detail information” option was selected.
aaa...a : Additional information
[Measures] Unnecessary
Chapter 2 Message List
294
iSM11575: LD Set detail information option was
selected.(<aaa...a>)
[Classification] INFO
[Explanation] “LD Set detail information” option was selected.
aaa...a : Additional information
[Measures] Unnecessary
iSM11576: ReallocationControl information
option was selected.
[Classification] INFO
[Explanation] “ReallocationControl information” option was selected.
[Measures] Unnecessary
iSM11577: Cache segment list information
option was selected.
[Classification] INFO
[Explanation] “Cache Segment list information” option was selected.
[Measures] Unnecessary
Chapter 2 Message List
295
iSM11578: Cache segment detail information
with LDN key option was selected.
[Classification] INFO
[Explanation] “Cache Segment detail information with LDN key” option was selected.
[Measures] Unnecessary
iSM11579: Cache segment detail information
with LD name key option was
selected.
[Classification] INFO
[Explanation] “Cache Segment detail information with LD Name key” option was selected.
[Measures] Unnecessary
iSM11580: Pool list information option was
selected.
[Classification] INFO
[Explanation] “Pool list information” option was selected.
[Measures] Unnecessary
Chapter 2 Message List
296
iSM11581: Pool detail information with Pool
Number key option was selected.
[Classification] INFO
[Explanation] “Pool detail information with Pool Number key” option was selected.
[Measures] Unnecessary
iSM11582: Pool detail information with Pool
Name key option was selected.
[Classification] INFO
[Explanation] “Pool detail information with Pool Number key” option was selected.
[Measures] Unnecessary
iSM11583: Snapshot Pool list information option
was selected.
[Classification] INFO
[Explanation] “Snapshot Pool list information” option was selected.
[Measures] Unnecessary
iSM11584: Snapshot Pool detail information with
Pool Name key option was selected.
[Classification] INFO
[Explanation] “Snapshot Pool detail information with Pool Name key” option was selected.
[Measures] Unnecessary
Chapter 2 Message List
297
iSM11585: Snapshot Pool detail information with
Pool Number key option was
selected.
[Classification] INFO
[Explanation] “Snapshot Pool detail information with Pool Number key” option was selected.
[Measures] Unnecessary
iSM11586: Snapshot LD list information option
was selected.
[Classification] INFO
[Explanation] “Snapshot LD list information” option was selected.
[Measures] Unnecessary
iSM11587: Snapshot LD detail information
option was selected.
[Classification] INFO
[Explanation] “Snapshot LD detail information” option was selected.
[Measures] Unnecessary
iSM11600: ATTENTION: Data on LD will be
deleted.
[Classification] INFO
[Explanation] Attention: Data on LD will be deleted.
[Measures] Please obey the instruction in the following message and go on the operation.
Chapter 2 Message List
298
iSM11601: Failed to communicate.
[Classification] INFO
[Explanation] It failed to communicate.
[Measures] Check whether iSMsvr has started.
iSM11602: Failed to set Log output environment.
[Classification] INFO
[Explanation] It failed in setting environment for Log output.
[Measures] Unnecessary
iSM11603: Only an Administrators group can
execute.
[Classification] INFO
[Explanation] Execution is allowed for users belonging to Administrators group only.
This message is output on Windows system.
[Measures] Log on by a user that belongs to Administrators group
iSM11604: Specified directory does not exist.
[Classification] INFO
[Explanation] Specified directory does not exist.
[Measures] Check the specified directory.
Chapter 2 Message List
299
iSM11605: Please wait a minute.
[Classification] INFO
[Explanation] The configuration information is now being obtained(/output). Please wait for a
minute.
[Measures] Please wait for a minute.
iSM11700: Please wait a minute.
[Classification] INFO
[Explanation] The volume list is now being created/updated. Please wait for a minute.
[Measures] Please wait for a minute.
iSM11701: Volume list is created successfully.
[Classification] INFO
[Explanation] It indicates that the volume list has been successfully created.
This message is output on Windows system.
[Measures] Unnecessary
iSM11702: Failed to make volume list data.
[Classification] ERROR
[Explanation] It failed in creating volume list.
This message is output on Windows system.
[Measures] A detailed error message is displayed. Execute the correct operation according
to the detailed error message.
Chapter 2 Message List
300
iSM11703: Option is insufficient.
[Classification] ERROR
[Explanation] It indicates that the required option is not specified or invalid option is specified.
[Measures] Specify the correct option.
iSM11704: Specified option are duplicated.
[Classification] ERROR
[Explanation] It indicates that the specified options are duplicated.
This message is output on Windows system.
[Measures] Specify the correct option.
iSM11705: Options which can not control are
specified.
[Classification] ERROR
[Explanation] It indicates that the specified option is not supported by the program.
This message is output on Windows system.
[Measures] Specify the correct option.
iSM11706: Too many options are specified.
[Classification] ERROR
[Explanation] It indicates that two or more options are specified at a time.
This message is output on Windows system.
[Measures] Specify the correct option.
Chapter 2 Message List
301
iSM11707: Combination of options is illegal.
[Classification] ERROR
[Explanation] It indicates that combination of options is illegal.
This message is output on Windows system.
[Measures] Specify the correct option.
iSM11708: Form of parameter is illegal.
[Classification] ERROR
[Explanation] It indicates that the form of parameter is illegal.
This message is output on Windows system.
[Measures] Specify the correct parameter form.
iSM11709: Parameter is too long.
[Classification] ERROR
[Explanation] It indicates that the parameter is too long.
This message is output on Windows system.
[Measures] Specify the correct parameter.
iSM11710: Conflict of volume list data has been
detected. Please update volume list
data.
[Classification] WARNING
[Explanation] Inconsistency was found in volume list. Volume list is old and is not consistent
with system status.
[Measures] Update the volume list.
Chapter 2 Message List
302
iSM11711: Volume list data does not exist.
[Classification] WARNING
[Explanation] Volume list does not exist.
[Measures] Create/update the volume list.
iSM11712: Volume list data is not created by the
command which supports property
display.
[Classification] WARNING
[Explanation] The property of the volume list could not be obtained because it is old.
[Measures] If the property is required, recreate the volume list.
iSM11713: Some definitions of control volume
are invalid.
[Classification] WARNING
[Explanation] Some definitions of control volume are invalid. The volume list was
created/updated ignoring the invalid definitions.
[Measures] Display the control volume and check its definition status. And, check the
definition of control volume and re-create the volume list.
iSM11714: Volume list data has no control
volume.
[Classification] WARNING
[Explanation] No control volume.
[Measures] If you want to use control volume, re-create and register a volume list after
defining control volume.
Chapter 2 Message List
303
iSM11721: Disk Array does not exist in volume
list data.
[Classification] ERROR
[Explanation] It indicates that the disk array information is not registered in the volume list.
[Measures] Check the connection between the host machine and the disk array, and newly
create the volume list.
iSM11722: Volume does not exist in volume list
data.
[Classification] ERROR
[Explanation] It indicates that the logical disk information is not registered in the volume list.
This message is output on Windows system.
[Measures] Bind the logical disk in the disk array, and newly create a volume list.
iSM11723: Specified ld_number does not exist
in volume list data.
[Classification] ERROR
[Explanation] It indicates that the specified logical disk is not registered in the volume disk.
This message is output on Windows system.
[Measures] Specify the correct logical disk.
Chapter 2 Message List
304
iSM11724: Specified ld_name does not exist in
volume list data.
[Classification] ERROR
[Explanation] It indicates that the specified logical disk name is not registered in the volume
list.
This message is output on Windows system.
[Measures] Specify the correct logical disk name.
iSM11725: Specified drive does not exist in
volume list data.
[Classification] ERROR
[Explanation] It indicates that the specified drive letter is not registered in the volume list.
This message is output on Windows system.
[Measures] Specify the correct drive letter.
iSM11726: Specified disk_number does not exist
in volume list data.
[Classification] ERROR
[Explanation] It indicates that the specified disk is not registered in the volume list.
This message is output on Windows system.
[Measures] Specify the correct disk.
Chapter 2 Message List
305
iSM11727: Specified HBT does not exist in
volume list data.
[Classification] ERROR
[Explanation] It indicates that the specified HBT is not registered in the volume list.
This message is output on Windows system.
[Measures] Specify the correct HBT.
iSM11728: Specified HBT or LUN does not exist
in volume list data.
[Classification] ERROR
[Explanation] It indicates that the specified HBT or LUN is not registered in the volume list.
This message is output on Windows system.
[Measures] Specify the correct HBT or LUN.
iSM11729: Specified Disk Array information
does not exist in volume list data.
[Classification] ERROR
[Explanation] It indicates that the disk array information is not registered in the volume list.
[Measures] Check the connection between the host machine and the disk array, and newly
create a volume list.
Chapter 2 Message List
306
iSM11730: Failed to get the specified Disk Array
information.
[Classification] ERROR
[Explanation] It indicates that the disk array information collection is failed.
This message is output on Windows system.
[Measures] Check the connection between the host machine and the disk array, and newly
create a volume list.
iSM11731: Specified Disk Array is not
supported.
[Classification] ERROR
[Explanation] It indicates that the specified disk array name is not correct
This message is output on Windows system.
[Measures] Specify the correct disk array name.
iSM11732: Specified Volume Name does not
exist in volume list data.
[Classification] ERROR
[Explanation] It indicates that the specified mount point volume is not registered in the volume
list.
This message is output on Windows system.
[Measures] Specify the correct mount point volume name.
Chapter 2 Message List
307
iSM11733: Failed to initialize an ODM session.
[Classification] ERROR
[Explanation] Failed in initialization of ODM session.
[Measures] Check that ODM environment is normal and retry processing.
Check that system memory capacity is sufficient and retry processing.
iSM11734: Failed to terminate an ODM session.
[Classification] ERROR
[Explanation] Failed in termination of ODM session.
[Measures] Check that ODM environment is normal, and then retry processing.
iSM11735: Failed to retrieve objects from ODM.
[Classification] ERROR
[Explanation] Failed in searching for an ODM object.
[Measures] Check that ODM environment is normal, and then retry processing.
iSM11736: Failed to write target-control volume
list data.
[Classification] ERROR
[Explanation] Failed in writing of target-control volume list data.
[Measures] Target-control volume list data may become invalid. Create a target-control
volume list again.
Chapter 2 Message List
308
iSM11737: Failed to get control volume
definitions.
[Classification] ERROR
[Explanation] Failed in obtaining control volume definitions.
[Measures] Check that control volume definition file is described correctly, and then retry
processing.
iSM11738: Failed to get target volume
definitions.
[Classification] ERROR
[Explanation] Failed in obtaining target volume definitions.
[Measures] Check that target volume definition file is described correctly, and then retry
processing.
iSM11739: Failed to get control volume list data.
[Classification] ERROR
[Explanation] Failed in obtaining control volume list data.
[Measures] Check settings for control volume and target volume, and make the settings for
control volume function effective, then newly create the volume list.
Chapter 2 Message List
309
iSM11740: Failed to get property of volume list
data.
[Classification] ERROR
[Explanation] Failed in obtaining the property of volume list data.
[Measures] Update the volume list, and then retry processing.
iSM11742: Failed to open control volume
definition file.
[Classification] ERROR
[Explanation] Failed in opening control volume definition file.
[Measures] Check that control volume definition file exists, and then retry processing.
iSM11743: Failed to open target volume
definition file.
[Classification] ERROR
[Explanation] Failed in opening target volume definition file.
[Measures] Check that target volume definition file exists, and then retry processing.
iSM11744: Failed to open target-control volume
list data.
[Classification] ERROR
[Explanation] Failed in opening target-control volume list.
[Measures] Target-control volume list data may be invalid. Create a target-control volume
list again.
Chapter 2 Message List
310
iSM11745: Failed to close control volume
definition file.
[Classification] ERROR
[Explanation] Failed in closing control volume definition file.
[Measures] Check that control volume definition file exists, and then retry processing.
iSM11746: Failed to close target volume
definition file.
[Classification] ERROR
[Explanation] Failed in closing target volume definition file.
[Measures] Check that target volume definition file exists, and then retry processing.
iSM11747: Failed to close target-control volume
list data.
[Classification] ERROR
[Explanation] Failed in closing target-control volume list.
[Measures] Target-control volume list data may be invalid. Create a target-control volume
list again.
iSM11748: Target-control volume list data has
invalid data.
[Classification] ERROR
[Explanation] Target-control volume list includes invalid data.
[Measures] Create a target-control volume list again.
Chapter 2 Message List
311
iSM11749: Control volume is not found.
[Classification] ERROR
[Explanation] Control volume is not found.
[Measures] Check that control volume definition file is described correctly, and then create a
target-control volume list again.
iSM11750: Failed to execute popen.
[Classification] ERROR
[Explanation] Execution of the popen() function failed.
This message is output on UNIX system.
[Measures] Check descriptions in operation log and remove causes of failure. Then retry
command execution.
Chapter 2 Message List
312
iSM11751: ReplicationControl or iSMvollist
command has already started.
iSM11751: iSMvollist command has already
started.
iSM11751: iSMmknod command has already
started.
iSM11751: iSM/Server has already started.
[Classification] ERROR
[Explanation] Reference or update of Volume List was executed during execution of the
replication control command.
The volume list is being updated by the iSMvollist command.
Update of Volume List was executed during execution of the iSMmknod
command.
The iSM server has already started. Update of Volume List cannot be executed.
[Measures] Retry after each process is completed.
iSM11755: Failed to execute ioscan.
[Classification] ERROR
[Explanation] Execution of ioscan command failed.
This message is output on UNIX system.
[Measures] If the operation trace is collected, use the operation trace and the error code to
find the cause and remove it.
Chapter 2 Message List
313
iSM11756: Illegal OS version
[Classification] ERROR
[Explanation] This version of OS is not supported for ReplicationControl.
This message is output on UNIX system.
[Measures] ReplicationControl cannot be used.
iSM11757: SCSI path-through driver is not
installed.
[Classification] ERROR
[Explanation] The SCSI path-through driver is not installed in the system.
This message is output on UNIX system.
[Measures] Install the SCSI path-through driver in the system.
Chapter 2 Message List
314
iSM11758: System call error (error code=<aaa>)
[Classification] ERROR
[Explanation] The system call failed when the volume list was created.
aaa : Error code
200: fork() fail
201: rename() fail
202: opendir() fail
203: execvp() fail
204: system() fail
205: unlink() fail
206: fopen() fail
207: fwrite() fail
208: rm command fail
209: mv command fail
210: lsdev command fail
211: mknod command fail
212: mksf command fail
213: child process dissipation
214: scsi open fail
215: scsi inquiry fail
216: scsi sense fail
217: fseek() fail
218: fread() fail
219: device information acquisition fail
(QueryDosDevice() fail, etc.)
220: popen() fail
230: open() fail
231: stat() fail
300: directory information acquisition fail
(GetSystemWindowsDirectory() fail,
etc.)
301: file exclusive lock fail (fcntl() fail, etc.)
[Measures] If the operation trace is collected, use the information in the operation trace and
the error code to find the cause and remove it.
Chapter 2 Message List
315
iSM11759: Failed to open control volume in
Diagnostic mode.
[Classification] ERROR
[Explanation] Control volume cannot be opened in Diagnostic mode.
[Measures] Check that LVM has not been activated on control volume and has not been
opened by other application in Diagnostic mode. Then retry processing.
iSM11760: Volume list data is locked by another
process.
[Classification] ERROR
[Explanation] Volume list has been created/modified by other process.
[Measures] After completion of a process, retry command execution.
iSM11781: Failed to open volume list data.
[Classification] ERROR
[Explanation] It indicates that it failed to open the volume list.
[Measures] The volume list may be invalid. Create a new volume list.
iSM11782: Failed to close volume list data.
[Classification] ERROR
[Explanation] It indicates that it failed to close the volume list.
[Measures] The volume list may be invalid. Create a new volume list.
Chapter 2 Message List
316
iSM11783: Failed to read volume list data.
[Classification] ERROR
[Explanation] It indicates that it failed to read the volume list.
[Measures] The volume list may be invalid. Create a new volume list.
iSM11784: Failed to write volume list data.
[Classification] ERROR
[Explanation] It indicates that it failed to write the volume list.
This message is output on Windows system.
[Measures] The volume list may be invalid. Create a new volume list.
iSM11785: Failed to seek volume list data.
[Classification] ERROR
[Explanation] It indicates that the file operation for the volume list is failed.
[Measures] The volume list may be invalid. Create a new volume list.
iSM11786: Failed to copy volume list data.
[Classification] ERROR
[Explanation] It indicates that it failed to copy the volume list.
This message is output on Windows system.
[Measures] The volume list may be invalid. Create a new volume list.
Chapter 2 Message List
317
iSM11787: Failed to rename volume list data.
[Classification] ERROR
[Explanation] It indicates that the file name of the volume list is not changed due to an error.
This message is output on Windows system.
[Measures] The volume list may be invalid. Create a new volume list.
iSM11791: Failed to read directory.
[Classification] ERROR
[Explanation] It indicates that the directory is not read.
This message is output on Windows system.
[Measures] Directory where the volume list is stored may be not specified. Create a new
volume list.
iSM11792: Failed to make directory.
[Classification] ERROR
[Explanation] It indicates that directory creation is failed.
This message is output on Windows system.
[Measures] Volume list table is created under the installation directory of an OS. Identify a
cause of inability to create a directory, and then create a volume list table again.
iSM11793: Failed to query device.
[Classification] ERROR
[Explanation] It indicates that device query is failed.
This message is output on Windows system.
[Measures] Check the connection between the host machine and the disk array, and newly
create a volume list.
Chapter 2 Message List
318
iSM11794: Failed to open scsi device.
[Classification] ERROR
[Explanation] It indicates that SCSI device is not opened due to an error.
[Measures] Check the connection between the host machine and the disk array, and newly
create a volume list.
iSM11795: Failed to get OS version.
[Classification] ERROR
[Explanation] It indicates that OS version is not obtained due to an error.
[Measures] This program is not supported by the OS you currently use. Use the OS
supporting this program to run this program.
iSM11796: Failed to allocate a memory space.
[Classification] ERROR
[Explanation] It indicates that the required memory space cannot be allocated.
[Measures] The required memory space may be insufficient. Allocate a required memory
space by expanding memory to run this program.
iSM11797: Target device does not exist.
[Classification] ERROR
[Explanation] It indicates that the disk array targeted for this program does not exist.
[Measures] Check the connection between the host machine and the disk array, and newly
create a volume list.
Chapter 2 Message List
319
iSM11799: Failed to execute system function.
[Classification] ERROR
[Explanation] It indicates that an error occurred in the system function of OS.
[Measures] OS may be in instability or invalid. Set the OS in a stable condition by
restarting or re-installing the OS.
iSM11801: Failed to create log files.
[Classification] INFO
[Explanation] Failed in creating log file.
[Measures] Check that creation of file is allowed in the log file output directory.
iSM11802: Started to get ‘<aaa...a>’ log.
[Classification] INFO
[Explanation] Obtaining log from disk array indicated by “aaa...a” started.
aaa...a : Disk array name
[Measures] Unnecessary
iSM11803: Succeed to get ‘<aaa...a>’ log.
[Classification] INFO
[Explanation] Obtaining log from disk array indicated by “aaa...a” was successful.
aaa...a : Disk array name
[Measures] Unnecessary
Chapter 2 Message List
320
iSM11804: Failed to get ‘<aaa...a>’ log.
[Classification] INFO
[Explanation] Failed in obtaining log from disk array indicated by “aaa...a”.
[Measures] Check status of iSM server and disk array, and then retry processing.
Chapter 2 Message List
321
iSM13000 ∼
iSM13200: <aaa...a>
[Classification] INFO
[Explanation] Executed command line.
aaa...a : Entered character string
[Measures] Unnecessary
iSM13201: Replicate Start <aaaa/bb/cc>
<dd:ee:ff> MV:<ggg...g> RV:<ggg...g>
[Classification] INFO
[Explanation] Replicate processing start message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
ggg...g : Volume name
[Measures] Unnecessary
iSM13202: Replicate Normal End <aaaa/bb/cc>
<dd:ee:ff> MV:<ggg...g> RV:<ggg...g>
[Classification] INFO
[Explanation] Replicate processing normal end message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
ggg...g : Volume name
[Measures] Unnecessary
Chapter 2 Message List
322
iSM13203: Replicate Abnormal End
<aaaa/bb/cc> <dd:ee:ff> MV:<ggg...g>
RV:<ggg...g>
[Classification] INFO
[Explanation] Replicate processing abnormal termination message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
ggg...g : Volume name
[Measures] Check the message displayed immediately before to handle it.
iSM13204: Restore Start <aaaa/bb/cc>
<dd:ee:ff> MV:<ggg...g> RV:<ggg...g>
[Classification] INFO
[Explanation] Restore processing start message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
ggg...g : Volume name
[Measures] Unnecessary
iSM13205: Restore Normal End <aaaa/bb/cc>
<dd:ee:ff> MV:<ggg...g> RV:<ggg...g>
[Classification] INFO
[Explanation] Restore processing normal termination message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
ggg...g : Volume name
[Measures] Unnecessary
Chapter 2 Message List
323
iSM13206: Restore Abnormal End
<aaaa/bb/cc> <dd:ee:ff> MV:<ggg...g>
RV:<ggg...g>
[Classification] INFO
[Explanation] Restore processing abnormal termination message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
ggg...g : Volume name
[Measures] Check the message displayed immediately before to handle it.
iSM13207: Separate Start <aaaa/bb/cc>
<dd:ee:ff> MV:<ggg...g> RV:<ggg...g>
[Classification] INFO
[Explanation] Separate processing start message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
ggg...g : Volume name
[Measures] Unnecessary
iSM13208: Separate Normal End <aaaa/bb/cc>
<dd:ee:ff> MV:<ggg...g> RV:<ggg...g>
[Classification] INFO
[Explanation] Separate processing normal termination message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
ggg...g : Volume name
[Measures] Unnecessary
Chapter 2 Message List
324
iSM13209: Separate Abnormal End
<aaaa/bb/cc> <dd:ee:ff> MV:<ggg...g>
RV:<ggg...g>
[Classification] INFO
[Explanation] Separate processing abnormal termination message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
ggg...g : Volume name
[Measures] Check the message displayed immediately before to handle it.
iSM13210: Change Start <aaaa/bb/cc>
<dd:ee:ff> MV:<ggg...g> RV:<ggg...g>
[Classification] INFO
[Explanation] Copy Control State change processing start message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
ggg...g : Volume name
[Measures] Unnecessary
iSM13211: Change Normal End <aaaa/bb/cc>
<dd:ee:ff> MV:<ggg...g> RV:<ggg...g>
[Classification] INFO
[Explanation] Copy Control State change processing normal termination message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
ggg...g : Volume name
[Measures] Unnecessary
Chapter 2 Message List
325
iSM13212: Change Abnormal End
<aaaa/bb/cc> <dd:ee:ff> MV:<ggg...g>
RV:<ggg...g>
[Classification] INFO
[Explanation] Copy Control State change processing abnormal termination message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
ggg...g : Volume name
[Measures] Check the message displayed immediately before to handle it.
iSM13213: Wait Abnormal End <aaaa/bb/cc>
<dd:ee:ff> MV:<ggg...g> RV:<ggg...g>
[Classification] INFO
[Explanation] The wait by the wait state processing has abnormally terminated.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
ggg...g : Volume name
[Measures] Check the message displayed immediately before to handle it.
iSM13214: These targets have already replicated.
MV:<aaa...a> RV:<aaa...a>
[Classification] INFO
[Explanation] Specified volume has already been replicated.
aaa...a : Volume name
[Measures] Unnecessary
Chapter 2 Message List
326
iSM13215: These targets have already separated.
(<aaa...a>) MV:<bbb...b> RV:<bbb...b>
[Classification] INFO
[Explanation] Specified volume has already been separated.
Separation condition is not displayed for separation normally ended
aaa...a : Separation condition
cancel : forced separation
fault : fault separation
bbb...b : Volume name
[Measures] Unnecessary
iSM13216: These targets have already restored.
MV:<aaa...a> RV:<aaa...a>
[Classification] INFO
[Explanation] Specified volume has already been restored.
aaa...a : Volume name
[Measures] Unnecessary
iSM13218: <aaa...a> <bbb...b>
[Classification] INFO
[Explanation] It indicates that a function was called. The name and parameter information of
function are edited and output with arbitrary character strings.
aaa...a : Function name
bbb...b : Function parameter information
[Measures] Unnecessary
Chapter 2 Message List
327
iSM13219: <aaa...a> return=<bbb...b> <ccc...c>
[Classification] INFO
[Explanation] It indicates that processing returned from a function. The name, return value and
return information of function are edited and output with arbitrary character
strings.
aaa...a : Function name
bbb...b : Return value of function (decimal)
ccc...c : Return information of function
[Measures] Unnecessary
iSM13220: Setting drive letter (<aaa...a>) has
succeeded.
iSM13220: Setting mount point (<bbb...b>) has
succeeded.
[Classification] INFO
[Explanation] The drive letter or the NTFS folder mount point was set successfully.
This message is output on Windows system.
aaa...a : Drive name
bbb...b : Path
[Measures] Unnecessary
Chapter 2 Message List
328
iSM13221: Resetting drive letter (<aaa...a>) has
succeeded.
iSM13221: Resetting mount point (<bbb...b>)
has succeeded.
[Classification] INFO
[Explanation] The drive letter or the NTFS folder mount point was canceled successfully.
This message is output on Windows system.
aaa...a : Drive name
bbb...b : Path
[Measures] Unnecessary
iSM13222: Reading signature succeeded.
<aaa...a> records
[Classification] INFO
[Explanation] The disk signature information was read successfully.
This message is output on Windows system.
aaa...a : Record count
[Measures] Unnecessary
iSM13223: Initializing signature succeeded.
volume=<aaa...a>
[Classification] INFO
[Explanation] The disk signature information was initialized successfully.
This message is output on Windows system.
aaa...a : Physical disk number
[Measures] Unnecessary
Chapter 2 Message List
329
iSM13224: MV is restored.
Volume Name:<aaa...a>
Mount Point:<bbb...b>
[Classification] INFO
[Explanation] The MV is to be restored by the restore command.
This message is output on Windows system.
aaa...a : Mount point volume name
bbb...b : Drive letters or NTFS folder name
[Measures] Unnecessary
If an error occurs during unmount of MV that is performed at restore start, set the
drive letters or mount the NTFS folder using the mount point volume name and
drive letters, or NTFS folder information output with this message before you
resume operation.
iSM13225: Flush Start <aaaa/bb/cc> <dd:ee:ff>
[Classification] INFO
[Explanation] Buffer flush processing start message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
[Measures] Unnecessary
iSM13226: Flush Normal End <aaaa/bb/cc>
<dd:ee:ff>
[Classification] INFO
[Explanation] Buffer flush processing normal end message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
[Measures] Unnecessary
Chapter 2 Message List
330
iSM13227: Flush Abnormal End <aaaa/bb/cc>
<dd:ee:ff>
[Classification] INFO
[Explanation] Buffer flush processing abnormal termination message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
[Measures] Check the message displayed immediately before to handle it.
iSM13228: Scan Start <aaaa/bb/cc> <dd:ee:ff>
[Classification] INFO
[Explanation] Device scan processing start message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
[Measures] Unnecessary
iSM13229: Scan Normal End <aaaa/bb/cc>
<dd:ee:ff>
[Classification] INFO
[Explanation] Device scan processing normal termination message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
[Measures] Unnecessary
Chapter 2 Message List
331
iSM13230: Scan Abnormal End <aaaa/bb/cc>
<dd:ee:ff>
[Classification] INFO
[Explanation] Device scan processing abnormal termination message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second.
[Measures] Check the message displayed immediately before to handle it.
iSM13231: Writing signature succeeded.
volume=<aaa...a>
[Classification] INFO
[Explanation] The disk signature information was written successfully.
This message is output on Windows system.
aaa...a : Physical disk number
[Measures] Unnecessary
iSM13232: Deleting record of specified volume
from signature map file succeeded.
volume=<aaa...a>
[Classification] INFO
[Explanation] The signature information of the specified disk was deleted from the signature
map file successfully.
This message is output on Windows system.
aaa...a : Physical disk number
[Measures] Unnecessary
Chapter 2 Message List
332
iSM13233: Deleting of signature information
from signature map file has
succeeded.
[Classification] INFO
[Explanation] All the disk signature information was deleted from the signature map file
successfully.
This message is output on Windows system.
[Measures] Unnecessary
iSM13234: Exporting file succeeded.
filename=<aaa...a>
iSM13234: Exporting file succeeded. <aaa...a>
records
[Classification] INFO
[Explanation] The disk signature information was written successfully.
This message is output on Windows system.
aaa...a : File name or record count
[Measures] Unnecessary
iSM13235: Importing file succeeded. <aaa...a>
records
[Classification] INFO
[Explanation] The disk signature information was read successfully.
This message is output on Windows system.
aaa...a : Record count
[Measures] Unnecessary
Chapter 2 Message List
333
iSM13238: Freeze of database is started.
<aaaa>/<bb>/<cc> <dd>:<ee>:<ff>
[Classification] INFO
[Explanation] Freeze of database is started.
aaaa/bb/cc : System date (year/month/day) when freeze of database started.
dd:ee:ff : System time (hour:minute:second) when freeze of database
started.
[Measures] Unnecessary
iSM13239: All of database were thawed.
<aaaa>/<bb>/<cc> <dd>:<ee>:<ff>
[Classification] INFO
[Explanation] All databases were thawed.
aaaa/bb/cc : System date (year/month/day) when databases were thawed.
dd:ee:ff : System time (hour:minute:second) when databases were thawed.
[Measures] Unnecessary
iSM13240: SnapshotBackup Start
<aaaa>/<bb>/<cc> <dd>:<ee>:<ff>
[Classification] INFO
[Explanation] Snapshot backup processing has started.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
[Measures] Unnecessary
Chapter 2 Message List
334
iSM13241: SnapshotBackup Normal End
<aaaa>/<bb>/<cc> <dd>:<ee>:<ff>
[Classification] INFO
[Explanation] Snapshot backup processing has terminated normally.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
[Measures] Unnecessary
iSM13242: SnapshotBackup Abnormal End
<aaaa>/<bb>/<cc> <dd>:<ee>:<ff>
[Classification] INFO
[Explanation] Snapshot backup processing has terminated abnormally.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
[Measures] Take measures with reference to a message that was output immediately before
this message.
iSM13243: SnapshotRestore Start
<aaaa>/<bb>/<cc> <dd>:<ee>:<ff>
[Classification] INFO
[Explanation] Snapshot restore processing has started.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
[Measures] Unnecessary
Chapter 2 Message List
335
iSM13244: SnapshotRestore Normal End
<aaaa>/<bb>/<cc> <dd>:<ee>:<ff>
[Classification] INFO
[Explanation] Snapshot restore processing has terminated normally.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
[Measures] Unnecessary
iSM13245: SnapshotRestore Abnormal End
<aaaa>/<bb>/<cc> <dd>:<ee>:<ff>
[Classification] INFO
[Explanation] Snapshot restore processing has terminated abnormally.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
[Measures] Take measures with reference to a message that was output immediately before
this message.
iSM13247: Command has completed
successfully.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] INFO
[Explanation] Command execution was successful.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Unnecessary
Chapter 2 Message List
336
iSM13248: Command has completed
successfully.(already)
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] INFO
[Explanation] The requested state has already been set up, and command execution was
successful.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Unnecessary
iSM13250: Snapshot has been deleted. SV:
<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] INFO
[Explanation] The snapshot has been deleted before a new snapshot creation.
aaa...a : Logical disk name for SV
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Unnecessary
Chapter 2 Message List
337
iSM13251: Create Start <aaaa/bb/cc>
<dd:ee:ff>
[Classification] INFO
[Explanation] Snapshot create processing start message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
[Measures] Unnecessary
iSM13252: Create Normal End <aaaa/bb/cc>
<dd:ee:ff>
[Classification] INFO
[Explanation] Snapshot create processing normal end message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
[Measures] Unnecessary
iSM13253: Create Abnormal End <aaaa/bb/cc>
<dd:ee:ff>
[Classification] INFO
[Explanation] Snapshot create processing abnormal termination message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
[Measures] Check the message displayed immediately before to handle it.
Chapter 2 Message List
338
iSM13254: Delete Start <aaaa/bb/cc> <dd:ee:ff>
[Classification] INFO
[Explanation] Snapshot delete processing start message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
[Measures] Unnecessary
iSM13255: Delete Normal End <aaaa/bb/cc>
<dd:ee:ff>
[Classification] INFO
[Explanation] Snapshot delete processing normal end message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
[Measures] Unnecessary
iSM13256: Delete Abnormal End <aaaa/bb/cc>
<dd:ee:ff>
[Classification] INFO
[Explanation] Snapshot delete processing abnormal termination message.
aaaa/bb/cc : Year/Month/Day
dd:ee:ff : Hour/Minute/Second
[Measures] Check the message displayed immediately before to handle it.
Chapter 2 Message List
339
iSM13400: Specified volume state has already
been set up.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] WARNING
[Explanation] Specified volume state has already been set up.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check specified volume state and re-execute.
iSM13401: This iSM/Server version does not
support necessary function.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] WARNING
[Explanation] There is a function that is not supported by the iSM server in use.
aaa...a : Process number
bbb…b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check the version of the iSM server.
If the version of the iSM server is older than that of ReplicationControl, upgrade
the version of the iSM server.
If the iSM server is Ver2.2, and if Not Available (volume unrecognizable) is set
as the RV restriction state, the state value cannot be obtained.
Chapter 2 Message List
340
iSM13403: Specified attribute (<aaa...a>) was
already set up to the ATgroup.
ATG=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
[Classification] WARNING
[Explanation] Specified attribute has already been set up to the AT-group.
aaa...a : Specified attribute value
bbb…b : AT-group name
ccc...c : Process number
ddd...d : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Confirm the condition for executing the specified command, and then re-execute
the command.
iSM13405: Specified targets are duplicated.
device name MV=<aaa...a>, device
name RV=<aaa...a>
[Classification] WARNING
[Explanation] Specified pair information is defined repeatedly. When iSMrc_sense is
executed, the volume defined on the MV side is repeated.
aaa...a : Volume name
[Measures] Check the volume specification.
Chapter 2 Message List
341
iSM13406: Specified targets are duplicated.
MV=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
iSM13406: Specified targets are duplicated.
volume=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] WARNING
[Explanation] MV or BV is defined repeatedly.
aaa...a : Volume name
bbb...b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check the volume specification.
iSM13407: Control path is blockaded.
file=<aaa...a> func=<bbb...b>
errno=<ccc> status=<ddd...d>
[Classification] WARNING
[Explanation] An alternate path is switched to since an access path error occurred.
This message is output on UNIX system.
aaa...a : Special file name
bbb...b : Function name
ccc : Error number
ddd...d : Error information
[Measures] Unnecessary
Chapter 2 Message List
342
iSM13408: These targets have replicated.
ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
iSM13408: These targets have replicated.
MV:<aaa...a> RV:<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] WARNING
[Explanation] A command, which must not be executed for volumes or AT-groups with
Replicate being completed, was executed.
aaa...a : AT-group name or volume name
bbb...b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Confirm the condition for executing the command, and then re-execute the
command.
Chapter 2 Message List
343
iSM13409: These targets have separated.
ATG=<aaa...a>>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
iSM13409: These targets have separated.
MV:<aaa...a> RV:<aaa...a>>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] WARNING
[Explanation] A command, which must not be executed for volumes or AT-groups with
Separate being completed, was executed.
aaa...a : AT-group name or volume name
bbb...b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Confirm the condition for executing the command, and then re-execute the
command.
Chapter 2 Message List
344
iSM13410: These targets have restored.
MV:<aaa...a> RV:<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] WARNING
[Explanation] A command, which must not be executed for volumes with Restore being
completed, was executed.
aaa...a : Volume name
bbb...b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Confirm the condition for executing the specified command, and then re-execute
the command.
iSM13411: Specified target is suspended.
[Classification] WARNING
[Explanation] The specified pair of volumes are in normal suspend state of copy control states.
[Measures] Execute the copy mode change instruction to restart the process by issuing the
copy control state change command.
iSM13412: Target pair’s copy mode is
background.
[Classification] WARNING
[Explanation] The specified pair of volumes are in background copy state of copy control
states.
[Measures] Change the copy control state to synchronous copy mode or semi-synchronous
copy mode, and then retry processing.
Chapter 2 Message List
345
iSM13413: Target pair’s copy mode is
foreground.
[Classification] WARNING
[Explanation] A request was made for a pair of volumes to change from the foreground copy
state into the synchronous copy mode or semi synchronous copy mode.
[Measures] Move the volumes into normal suspend state, and then change the copy mode.
iSM13414: Conflict of volume list data has been
detected. Please update volume list
data.
[Classification] WARNING
[Explanation] Inconsistency was found in volume list. Volume list is old and is not consistent
with system status.
[Measures] Update the volume list.
iSM13415: Specified volume was ignored.
(<aaa...a>)
[Classification] WARNING
[Explanation] Specified volume was ignored.
aaa...a : Ignored volume (MV or RV)
[Measures] Take measures with reference to a message that was output immediately before
this message.
Chapter 2 Message List
346
iSM13480: Target ATgroup is replicating now.
ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] WARNING
[Explanation] The specified AT-group is in the state of replicate start (Rpl/start) or replicate
execution (Rpl/exec), and replicate has been already started.
aaa...a : AT-group name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Confirm the condition for executing the specified command, and then re-execute
the command.
iSM13481: Target ATgroup is restoring now.
ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] WARNING
[Explanation] The specified AT-group is in the state of restore execution (Rst/exec), and restore
has been already started.
aaa...a : AT-group name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Confirm the condition for executing the specified command, and then re-execute
the command.
Chapter 2 Message List
347
iSM13482: Target ATgroup is separating now.
ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] WARNING
[Explanation] The specified AT-group is in the state of separate start (Sep/start) or separate
execution (Sep/exec), separation has been already started.
aaa...a : AT-group name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Confirm the condition for executing the specified command, and then re-execute
the command.
iSM13483: Target ATgroup is fault.
ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] WARNING
[Explanation] The specified AT-group is in the state of failure separation (Fault), and
synchronization has already stopped.
aaa...a : AT-group name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Confirm the condition for executing the specified command, and then re-execute
the command.
Chapter 2 Message List
348
iSM13500: Insufficient option. (<aaa...a>)
[Classification] ERROR
[Explanation] The specified command does not have some required arguments, or invalid
arguments are specified.
When -file option is specified, an available option is specified for the pair
specified by the replication operation file.
() may or may not be displayed.
aaa...a : Specified value
[Measures] Specify the necessary arguments in the command line.
If -file option is specified, check the replication operation file.
iSM13501: Specified options are duplicated.
(<aaa...a>)
[Classification] ERROR
[Explanation] The same argument is specified more than once in the command line.
aaa...a : Specified value
[Measures] Specify only one argument.
iSM13502: Options which can not be omitted are
specified. (<aaa...a>)
[Classification] ERROR
[Explanation] An argument which cannot be omitted is omitted.
aaa...a : Specified value
[Measures] Check the input format and enter it again.
Chapter 2 Message List
349
iSM13503: Too many options are specified.
(<aaa...a>)
[Classification] ERROR
[Explanation] Too many values are specified in the argument.
aaa...a : Specified value
[Measures] Check the input format and enter it again.
iSM13504: Illegal combination of options.
(<aaa...a>)
[Classification] ERROR
[Explanation] An invalid combination of arguments are specified in the command line.
aaa...a : Specified value
[Measures] Check the input format and enter it again.
iSM13505: Illegal control option.
[Classification] ERROR
[Explanation] The argument you specified in the command line cannot be specified.
[Measures] Check the input format and enter it again.
iSM13506: Illegal mvflg type. (<aaa...a>)
[Classification] ERROR
[Explanation] The value specified as MV type is invalid.
aaa...a : Specified value
[Measures] Specify a correct value.
Chapter 2 Message List
350
iSM13507: Illegal rvflg type. (<aaa...a>)
[Classification] ERROR
[Explanation] The value specified as RV type is invalid.
aaa...a : Specified value
[Measures] Specify a correct value.
iSM13508: Illegal cprange type. (<aaa...a>)
[Classification] ERROR
[Explanation] The value specified in -cprange is invalid.
aaa...a : Specified value
[Measures] Specify a correct value.
iSM13509: Illegal cpmode type. (<aaa...a>)
[Classification] ERROR
[Explanation] The value specified in -cpmode is invalid.
aaa...a : Specified value
[Measures] Specify a correct value.
iSM13510: Illegal rvacc type. (<aaa...a>)
[Classification] ERROR
[Explanation] The value specified in -rvacc for RV is invalid.
aaa...a : Specified value
[Measures] Specify a correct value.
Chapter 2 Message List
351
iSM13511: Illegal force type. (<aaa...a>)
[Classification] ERROR
[Explanation] The value specified in -force is invalid.
aaa...a : Specified value
[Measures] Specify a correct value.
iSM13512: Illegal copy mode.
[Classification] ERROR
[Explanation] A copy mode is not specified.
Or, the specified copy mode is not supported as copy control mode for the target
pair.
[Measures] Specify a correct value.
Chapter 2 Message List
352
iSM13513: Volume (<aaa...a>) does not exist in
volume list.
[Classification] ERROR
[Explanation] Specified volume does not exist in the volume list.
If you use the control volume for operation, the specified volume or volume
paired with the specified volume should be accessible from the relevant business
server with the Access Control or other functions.
When operating the remote disk array pair through remote operation, you can
operate the target pairs and volumes on the level accessible from the business
server as well as one level below and above it. Specified pair and volume cannot
be operated during remote operation if the disk array is shutdown or in the freeze
status, if the link path between disk arrays failed, or if the disk array does not
have required functions or product license.
Note that () may or may not be displayed.
aaa...a : Mount point volume name
[Measures] Check the volume and re-execute or re-create a volume list.
Check that specified volume is accessible from the relevant server when using
the control volume for operation.
Check that the disk array and link path statuses are normal when operating the
remote disk array pair through remote operation. Both of the local and remote
disk arrays should have the RemoteDataReplication/DisasterRecovery function
and product license.
Chapter 2 Message List
353
iSM13514: Volume name is too long. (<aaa...a>)
[Classification] ERROR
[Explanation] The specified volume name is too long.
aaa...a : Specified volume name
[Measures] Specify the volume within the following range:
Logical disk name: within 24 1-byte characters
Special file name: within 32 1-byte characters
Volume group name: within 32 1-byte characters
Disk group name: within 32 1-byte characters
Mount point volume name: within 52 1-byte characters
Path name (drive letters, NTFS folder name): within 260 1-byte characters
iSM13515: Number of MV is too many.
[Classification] ERROR
[Explanation] Two or more MVs are specified when the RV volume is not in the volume group
or disk group.
This message is output on UNIX system.
[Measures] Specify only one volume for the MV.
iSM13516: Number of RV is too many.
[Classification] ERROR
[Explanation] Two or more RVs are specified when the MV volume is not in the volume group
or disk group.
This message is output on UNIX system.
[Measures] Specify only one volume for the RV.
Chapter 2 Message List
354
iSM13517: Number of LD(MV) is not equal to that
of LD(RV).
[Classification] ERROR
[Explanation] The number of volumes specified for MV and RV are different.
This message is output on UNIX system.
[Measures] Make the number of MV and RV volumes equal.
iSM13518: Illegal value of -wait [second].
(<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The value specified for the monitoring time interval is out of the specified range.
aaa...a : Specified value
bbb...b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a value within the specified range.
Chapter 2 Message List
355
iSM13519: Illegal value of RPL_WATCHDEV.
(<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The value specified in the environment variable RPL_WATCHDEV is invalid.
(UNIX)
The value specified in RPL_WATCHDEV of the replication operation option
setting file is not allowed. (Windows)
aaa...a : Specified value
bbb...b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a value within the specified range.
iSM13520: Illegal value of RPL_ENDWATCHDEV.
(<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The value specified in the environment variable RPL_ENDWATCHDEV is
invalid.
The value specified in RPL_ENDWATCHDEV of the replication operation
option setting file is not allowed.
aaa...a : Specified volume
bbb...b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a value within the specified range.
Chapter 2 Message List
356
iSM13521: Specified volume group does not
exist vg=<aaa...a>
iSM13521: Specified disk group does not exist
dg=<bbb...b>
[Classification] ERROR
[Explanation] An invalid volume group or disk group is specified.
This message is output on UNIX system.
aaa...a : Volume group
bbb...b : Disk group
[Measures] Specify the correct volume group or disk group.
iSM13522: No such VG
iSM13522: No such DG
[Classification] ERROR
[Explanation] A volume group or disk group that does not exist is specified.
This message is output on UNIX system.
[Measures] Specify the correct volume group or disk group.
iSM13523: Illegal targets are specified.
[Classification] ERROR
[Explanation] The specified pair is invalid.
[Measures] Specify a correct pair.
Chapter 2 Message List
357
iSM13524: No such file filename=<aaa...a>
errno=<bbb>
[Classification] ERROR
[Explanation] The specified file does not exist.
aaa...a : File name
bbb : Error number
[Measures] Specify a correct file name.
iSM13525: Illegal file type filename=<aaa...a>
[Classification] ERROR
[Explanation] The specified file type cannot be processed.
aaa...a : File name
[Measures] Specify the file created by the regular file. (UNIX)
Specify a file created as a text file. (Windows)
iSM13526: File open error occurred.
filename=<aaa...a> errno=<bbb>
[Classification] ERROR
[Explanation] A file open error occurred.
aaa...a : File name
bbb : Error number
[Measures] Check whether the file has no error.
Chapter 2 Message List
358
iSM13527: Illegal character is included.
filename=<aaa...a> line=<bbb...b>
[Classification] ERROR
[Explanation] An invalid character exists in the description in the file.
aaa...a : File name
bbb...b : Number of lines
[Measures] Correct the file and execute it again.
iSM13528: Line has too many characters.
filename=<aaa...a> line=<bbb...b>
[Classification] ERROR
[Explanation] More than 1024 characters (1-byte) are specified in one line.
aaa...a : File name
bbb...b : Number of lines
[Measures] Correct the file and execute it again.
iSM13529: Illegal rvdata type. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] Value specified for -rvdata option is invalid.
aaa...a : Specified value
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a correct value and execute it again.
Chapter 2 Message List
359
iSM13530: Illegal MV type is specified.
filename=<aaa...a> line=<bbb...b>
[Classification] ERROR
[Explanation] An invalid value was specified in MV Type.
aaa...a : File name
bbb...b : Number of lines
[Measures] Specify a correct value for MV Type..
iSM13531: Illegal iopath type. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] Value specified for -iopath option is invalid.
aaa...a : Specified value
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a correct value.
iSM13532: Illegal RV type is specified.
filename=<aaa...a> line=<bbb...b>
[Classification] ERROR
[Explanation] An invalid value was specified in RV Type.
aaa...a : File name
bbb...b : Number of lines
[Measures] Specify a correct value for RV type.
Chapter 2 Message List
360
iSM13533: MV name is too long. error
filename=<aaa...a> line=<bbb...b>
iSM13533: RV name is too long. error
filename=<aaa...a> line=<bbb...b>
iSM13533: Specified volume name is too long.
error filename=<aaa...a>
line=<bbb...b>
[Classification] ERROR
[Explanation] The specified volume name is too long.
aaa...a : File name
bbb...b : Number of lines
[Measures] Specify the volume within the following range:
Logical disk name: within 24 1-byte characters
Special file name: within 32 1-byte characters
Volume group name: within 32 1-byte characters
Disk group name: within 32 1-byte characters
Mount point volume name: within 52 1-byte characters
Path name (drive letters, NTFS folder name): within 260 1-byte characters
Chapter 2 Message List
361
iSM13535: ATgroup does not exist.
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
iSM13535: ATgroup does not exist.
ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The specified AT-group does not exist. Or, no operational AT-group is found.
aaa...a : Specified AT-group name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check whether the specified AT-group name is correct, and then retry processing.
Or, register MV or RV in the specified AT-group with the volume list, and then
retry processing.
iSM13536: Aborted to read the file.
filename=<aaa...a> line=<bbb...b>
[Classification] ERROR
[Explanation] An error is detected in the execution of fgets function. File read out is
interrupted since failed to obtain volume group or disk group information.
aaa...a : File name
bbb...b : Number of lines
[Measures] Check that the file is not destroyed, and retry the command. Or, Specify a
correct volume group or disk group.
Chapter 2 Message List
362
iSM13537: Number of LD(MV) is not equal to that
of LD(RV). filename=<aaa...a>
line=<bbb...b>
[Classification] ERROR
[Explanation] The number of volumes specified for MV and RV are different.
aaa...a : File name
bbb...b : Number of lines
[Measures] Make the number of volumes of MV and RV equal.
iSM13538: Specified file is empty.
filename=<aaa...a> line=<bbb...b>
[Classification] ERROR
[Explanation] Volume information is not defined in the specified file.
aaa...a : File name
bbb...b : Number of lines
[Measures] Define the volume information.
iSM13539: Specified RV is not available to
‘-force’.
[Classification] ERROR
[Explanation] -force all or rv cannot be specified when RV is not visible from the self host.
[Measures] Specify mv when RV is not visible from the self host.
Chapter 2 Message List
363
iSM13540: Illegal volflg type (<aaa...a>)
[Classification] ERROR
[Explanation] The value specified in the -vol type is invalid.
aaa...a : Specified value
[Measures] Specify a correct value.
iSM13541: Semi-sync mode is not available to
DynamicDataReplication.
[Classification] ERROR
[Explanation] Semi-sync mode cannot be specified for pairs in the same disk array.
[Measures] Change the copy mode and execute it.
iSM13542: Specified targets are not paired.
[Classification] ERROR
[Explanation] Request has been issued to a volume that is not paired or forcibly unpaired. If
RemoteDataReplication is used, the volume information on the paired remote
side cannot be obtained because a fault has occurred in the link path to the disk
array on the remote side or the disk array is in the shutdown or freeze state.
[Measures] Check the state of the volume , and then re-execute the command. If
RemoteDataReplication is used, check the state of the disk array on the remote
side and the state of the link path, and then re-execute the command.
Chapter 2 Message List
364
iSM13543: Illegal atmode type. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The value specified in the -atmode option is invalid.
aaa...a : Specified value
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a correct value.
iSM13544: Illegal value of concentrator number.
(<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The value specified in the -concnum option is invalid.
aaa...a : Specified value
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a correct value.
Chapter 2 Message List
365
iSM13545: Illegal site type. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The value specified in the -site option is invalid.
aaa...a : Specified value
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a correct value.
iSM13547: Specified partition does not exist.
[Classification] ERROR
[Explanation] Specified partition does not exist.
This message is output on Windows system.
[Measures] Check the specified partition and retry it
iSM13548: Making MV& RV device list failed.
[Classification] ERROR
[Explanation] Creation of internal information of the specified volume failed.
[Measures] Check the message displayed immediately before to handle it.
Chapter 2 Message List
366
iSM13549: Failed to replicate.
[Classification] ERROR
[Explanation] Replicate failed.
[Measures] Check the message displayed immediately before to handle it.
iSM13550: Failed to restore.
[Classification] ERROR
[Explanation] Restore failed.
[Measures] Check the message displayed immediately before to handle it.
iSM13551: Failed to separate.
[Classification] ERROR
[Explanation] Separate failed.
[Measures] Check the message displayed immediately before to handle it.
iSM13552: Failed to change.
[Classification] ERROR
[Explanation] Change of the copy control state or change of the AT-group attribute failed.
[Measures] Check the message displayed immediately before to handle it.
Chapter 2 Message List
367
iSM13553: Illegal value of RPL_LIMWATCHDEV.
(<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The specified value of an environment variable or RPL_LIMWATCHDEV of
the replication operation option setting file is out of the specified range.
aaa...a : Specified value
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a value within the specified range.
iSM13554: Specified ATgroup name is too long.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] The specified AT-group name is too long.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify an AT-group name within 32 characters (1-byte).
Chapter 2 Message List
368
iSM13555: Checking status failed. (detail error
code=<aaa>)
[Classification] ERROR
[Explanation] A failure was detected during wait mode process and volume state could not be
obtained.
aaa : Error code
The following show major error codes.
1 : SCSI I/O failure
4 : system error occurred
7 : SCSI open failure
8 : SCSI close failure
9 : volume search error
48 : volume list lock failure
49 : volume list state error detection
53 : freeze state detection
54 : copy suspend state detection
55 : replicate state detection
56 : restore state detection
57 : separate state detection
58 : background copy state detection
61 : memory allocation failure
63 : foreground copy state detection
[Measures] Take appropriate measures by identifying the error cause from the operation
trace information and detailed error code.
Chapter 2 Message List
369
iSM13556: SCSI I/O error has occurred.
[Classification] ERROR
[Explanation] SCSI I/O error has occurred.
[Measures] A failure may be occurring in connection with disk array. Check status of FC
connection and then retry processing. If no problems are found in status of FC
connection, check the following for the specified volume. Then retry
processing.
- A special file or physical disk exists for the volume.
- The volume is not set to Not Ready or Not Available.
- Volume list was updated to the newest information after the configuration of
the disk array or system was changed.
- The target volume was registered in the volume list.
If RemoteDataReplication is used, a fault may have occurred in the link path to
the disk array on the remote side or the disk array may be in the shutdown or
freeze state. Check the state of the disk array on the remote side and the state of
the link path.
iSM13557: SCSI open has failed.
[Classification] ERROR
[Explanation] SCSI open error occurred.
[Measures] Check that the user with the access right to the volume exists or that the disk
number corresponding to the specified volume exists, and execute it again.
iSM13558: SCSI close has failed.
[Classification] ERROR
[Explanation] SCSI close error occurred.
[Measures] Check that the user with the access right to the volume exists or that the disk
number corresponding to the specified volume exists, and execute it again.
Chapter 2 Message List
370
iSM13559: Parameter error occurred.
[Classification] ERROR
[Explanation] Parameter error occurred in the internal processing.
[Measures] Collect information on operation trace
iSM13560: State of the specified ATgroup is
unknown.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] State of the specified AT-group is unknown.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Processing to the specified AT-group is not permitted.
iSM13561: Platform of LD specified is
unavailable.
[Classification] ERROR
[Explanation] The command was issued to the volume with OS type not supported.
[Measures] Check the OS type and execute it again.
Chapter 2 Message List
371
iSM13562: RV is omitted.
[Classification] ERROR
[Explanation] RV was omitted for MV with the pair setting of multiple RVs.
[Measures] Specify RV and execute it again.
iSM13563: System call error (error code=<aaa>)
[Classification] ERROR
[Explanation] It failed in system calling.
aaa : System error number
[Measures] If the operation trace is collected, use the information in the operation trace and
the error code to find the cause and remove it.
iSM13564: This connection does not allow
replicating & restoring at the same
time.
[Classification] ERROR
[Explanation] The operation could not be executed because the upper or lower pair of the
specified volume has already been in Replicate or Restore state.
[Measures] Make the upper or lower pair Separate, and execute it again.
Chapter 2 Message List
372
iSM13565: Upper pair is not separated.
[Classification] ERROR
[Explanation] The activity state of the pair of the specified MV and the upper pair is not
Separate.
[Measures] Make the activity state of the upper pair separate state, and retry processing.
To replicate the target pair when the activity state of the upper pair is Replicate,
set the copy control mode on the target pair to the background copy mode and
replicate it.
iSM13566: Lower pair is not separated.
[Classification] ERROR
[Explanation] The activity state of the pair of the specified RV and the lower pair is not
Separate.
[Measures] Make the activity state of the lower pair separate state, and retry processing.
To replicate the target pair when the activity state of the lower pair is Replicate,
the copy control mode on the lower pair must be set to the background copy
mode in advance.
iSM13567: Specified Disk Array’s status is
‘freeze’.
[Classification] ERROR
[Explanation] The disk array where the specified MV or RV is stored is in the freeze state, or
the disk array on the remote side is in the freeze state when
RemoteDataReplication is used.
[Measures] Cancel the Freeze state and execute it again.
Chapter 2 Message List
373
iSM13568: Target ATgroup is processing
Atomic-break now. ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] Request was rejected because atomic-break is operating on the specified
AT-group.
aaa...a : AT-group name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check the state of the AT-group and the state of the pair registered in the
AT-group. Take recovery action for continuing operation according to the
AT-group consistency state and sync state. And also remove the cause of copy
fault.
Chapter 2 Message List
374
iSM13569: Target ATgroup is replicating now.
ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
iSM13569: Target pair is replicating now.
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The specified pair is being replicated. Or, the specified AT-group is in the
replicate start (Rpl/start) or replicate execution (Rpl/exec) state.
aaa...a : AT-group name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Retry processing after the state becomes the replicate synchronous (Rpl/sync).
Chapter 2 Message List
375
iSM13570: Target ATgroup is restoring now.
ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
iSM13570: Target pair is restoring now.
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The specified pair is being restored. Or, the specified AT-group is in the restore
execution (Rst/exec) state.
aaa...a : AT-group name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] If the target is a pair, resume processing after the sync state is established. If it
is an AT-group, retry processing after the state becomes Separated by sync state
establishment.
Chapter 2 Message List
376
iSM13571: Target ATgroup is separating now.
ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
iSM13571: Target pair is separating now.
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The specified pair is being separated. Or the specified AT-group is in the
separate start (Sep/start) or separate execution (Sep/exec) state.
aaa...a : AT-group name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Retry processing after the separated state is established.
iSM13572: Target ATgroup is not suspended.
ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The sync state of the specified AT-group is not replicate suspend (Rpl/suspend)
or restore suspend (Rst/suspend).
aaa...a : AT-group name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check the state of the AT-group, and retry replicate or restore if necessary.
Chapter 2 Message List
377
iSM13573: Target ATgroup is not replicated.
ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
iSM13573: Target pair is not replicated or
restored.
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The activity state of the specified pair is not the Replicate or Restore state. Or,
the sync state of the specified AT-group is not replicate synchronous.
aaa...a : AT-group name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] If the target is a pair, retry processing when the activity state is replicate
synchronous or sync state. If the target is an AT-group, make the AT-group
replicate synchronous, and then re-execute the command.
iSM13574: Specified path (<aaa...a>) does not
exist.
[Classification] ERROR
[Explanation] Specified path does not exist.
aaa...a : Specified value
[Measures] Check the path and retry it.
Chapter 2 Message List
378
iSM13575: Unexpected error occurred.
[Classification] ERROR
[Explanation] Message for an unexpected error.
[Measures] Check library version for the replication operation, and check firmware revision
of disk array device.
iSM13576: Targets may not be a pair, or
unexpected error occurred.
[Classification] ERROR
[Explanation] Specified volume is not paired. Or, it failed to obtain the pair activity state
information.
[Measures] Retry after confirming the pair state of the specified volume.
iSM13577: These targets are replicating now.
MV:<aaa...a> RV:<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] A non-executable replication operation command was performed for the pair in
Replicate execution.
aaa...a : Volume name
bbb...b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check the execution conditions of the specified command and execute it again.
Chapter 2 Message List
379
iSM13578: These targets are separating now.
MV:<aaa...a> RV:<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] A non-executable replication operation command was performed for the pair in
Separate execution.
aaa...a : Volume name
bbb...b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check the execution conditions of the specified command and execute it again.
iSM13579: These targets are restoring now.
MV:<aaa...a> RV:<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] A non-executable replication operation command was performed for the pair in
Restore execution.
aaa...a : Volume name
bbb...b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check the execution conditions of the specified command and execute it again.
Chapter 2 Message List
380
iSM13580: Target ATgroup is suspended now.
ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The sync state of the specified AT-group has become replicate suspend
(Rpl/suspend) or restore suspend (Rst/suspend).
aaa...a : AT-group name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check the state of the AT-group, and resume replicate or restore.
iSM13581: These targets have replicated.
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
iSM13581: These targets have replicated.
ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] A command not allowed for replicated volume or AT-group was executed.
aaa...a : AT-group name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check executing condition of the command and retry command execution.
Chapter 2 Message List
381
iSM13582: These targets have separated.
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
iSM13582: These targets have separated.
ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] A command not allowed for separated volume or AT-group was executed.
aaa...a : AT-group name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check executing condition of the command and retry command execution.
iSM13583: These targets have restored.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] A command not allowed for restored volume was executed.
aaa...a : Process number
bbb…b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check executing condition of the command and retry command execution.
Chapter 2 Message List
382
iSM13584: Not enough memory (<aaa...a>)
errno=<bbb>
[Classification] ERROR
[Explanation] Insufficient memory to execute the process.
() and error number may or may not be displayed.
aaa...a : Resource name
bbb : Error number
[Measures] Add more memory to the system.
iSM13585: Volume list is missing or unexpected
error occurred. error code=<aa>
[Classification] ERROR
[Explanation] Processing is interrupted because the volume list table does not exist.
aa : Error code
-2: fopen() failure
-3: Internal error
-4: fread() failure
[Measures] Create the volume list table and re-execute.
Chapter 2 Message List
383
iSM13586: Target ATgroup is fault.
ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The sync state of the specified AT-group has become failure separation (Fault).
aaa...a : AT-group name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] This AT-group may have been forcibly separated by another process or it may
have a fault. Check the state of the AT-group, and re-execute replicate or
restore.
iSM13587: Specified drive letter has already
existed.
[Classification] ERROR
[Explanation] Specified drive has already existed.
This message is output on Windows system.
[Measures] Check the drive letter, and re-execute.
Chapter 2 Message List
384
iSM13588: Specified ATgroup has already
existed.
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
iSM13588: Specified ATgroup has already
existed. ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The specified AT-group already exists.
aaa...a : AT-group name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] A newly created AT-group must have a unique name in the system.
iSM13589: Specified ATgroup is not empty.
ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The specified AT-group has some registered pairs.
aaa...a : AT-group name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] To delete an AT-group, all the registered pairs must be deleted in advance.
Chapter 2 Message List
385
iSM13590: Specified ATgroup cannot be
operated from this site.
ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] Operation of the specified AT-group cannot be executed from the current
position.
AT-group binding is enabled on the concentrator side.
aaa...a : AT-group name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check the operation position, and re-execute the command from the position
where the operation is possible.
iSM13591: Volume list error.
[Classification] ERROR
[Explanation] The volume list table is invalid.
Or, a volume list created by the iSMvollist command of a version that is older
than Ver1.4 cannot be used for operation of AT-groups.
[Measures] Create a new volume list table.
Chapter 2 Message List
386
iSM13592: Target ATgroup is not separated.
ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
iSM13592: Target pair is not separated.
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The activity status of the specified pair is not Separate. Or, the specified
AT-group sync state is not separated (Separated) or failure separation (Fault).
aaa...a : AT-group name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] If the target is a pair, retry processing when the activity state is separated. If the
target is an AT-group, make the AT-group separated (Separated) or failure
separation (Fault) state, and then re-execute the command.
iSM13593: Target ATgroup is not fault.
ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The specified AT-group sync state is not failure separation (Fault).
aaa...a : AT-group name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check the state of the AT-group. If you need to interrupt replicate or restore,
forcibly separate it.
Chapter 2 Message List
387
iSM13594: License for RemoteDataReplication
/DisasterRecovery is locked.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] The product of RemoteDataReplication/DisasterRecovery is not purchased.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] To perform the RemoteDataReplication/DisasterRecovery operation, purchase
the RemoteDataReplication/DisasterRecovery product.
iSM13595: License for DynamicDataReplication
is locked.
[Classification] ERROR
[Explanation] The DynamicDataReplication product has not been purchased.
[Measures] To perform the DynamicDataReplication operations, purchase the
DynamicDataReplication product.
iSM13596: License for RemoteDataReplication is
locked.
[Classification] ERROR
[Explanation] The RemoteDataReplication product has not been purchased.
[Measures] To perform the RemoteDataReplication operations, purchase the
RemoteDataReplication product.
Chapter 2 Message List
388
iSM13597: DynamicDataReplication is not
supported.
[Classification] ERROR
[Explanation] The DynamicDataReplication function is not supported.
[Measures] ReplicationControl cannot be used.
iSM13598: RemoteDataReplication is not
supported.
[Classification] ERROR
[Explanation] The RemoteDataReplication function is not supported.
[Measures] ReplicationControl cannot be used.
iSM13599: License for this command is locked.
[Classification] ERROR
[Explanation] The product function necessary to execute the command is not supported, or the
license of the product is not unlocked.
[Measures] Check whether the target unit supports the necessary product function and the
license of the product has been unlocked.
Chapter 2 Message List
389
iSM13600: Specified drive has multiple
partitions/extents.
[Classification] ERROR
[Explanation] Specified physical disk is configured in multiple partitions, or logical volume in
the specified volume disk is configured in multiple extensions (physical disk).
This message is output on Windows system.
[Measures] Physical disk status can be confirmed by Disk Management (Computer
Management) for Windows. Settings for the replication operation option
setting file (iSMrpl.ini) must be changed to execute operation for multiple
partitions. However, operation for multiple extensions is not allowed.
iSM13601: Specified drive is not basic disk.
[Classification] ERROR
[Explanation] Specified drive is not a basic disk.
This message is output on Windows system.
[Measures] Specify a basic disk and retry it.
iSM13602: Specified partitions is not
primary/extended partition.
[Classification] ERROR
[Explanation] The partition to which the mount operation is executed is not primary or
extended partition.
This message is output on Windows system.
[Measures] Specify a primary or extended partitions and retry it.
Chapter 2 Message List
390
iSM13603: Partition that specified drive
character assigned has multiple
partitions/extents.
[Classification] ERROR
[Explanation] Specified disk to which the drive letter is allocated is configured in multiple
partitions, or volume in the disk is configured in multiple extensions (physical
disk).
This message is output on Windows system.
[Measures] Physical disk status can be confirmed by Disk Management (Computer
Management) for Windows. Settings for the replication operation option
setting file (iSMrpl.ini) must be changed to execute operation for multiple
partitions. However, operation for multiple extensions is not allowed.
iSM13604: Specified partition does not exist.
[Classification] ERROR
[Explanation] Specified partition does not exist.
This message is output on Windows system.
[Measures] Check the partition and re-execute.
iSM13605: Specified drive number does not
exist.
[Classification] ERROR
[Explanation] Specified disk number does not exist.
This message is output on Windows system.
[Measures] Check the specified physical drive and re-execute.
Chapter 2 Message List
391
iSM13606: There is no authority to access the
specified volume.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
iSM13606: There is no authority to access the
specified pair.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] The operation could not be executed because access to the specified pair or
volume is not permitted.
Operation using control volume requires that either the specified volume or the
volume paired with the specified volume be made accessible from the business
server by a function such as access control.
In remote operation of a pair of the disk array on the remote side, the effective
range of pairs and volumes is one layer farther that is linked with the accessible
volume from the business server. In remote operation, operation of the
specified pair or volume is disabled when the disk array is in the state of
shutdown or freeze, when a fault occurs on the link path between the disk arrays,
or when the user does not have the function or the license of the product
necessary for the disk array.
aaa...a : Process number
bbb...b : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check whether the specified volume is accessible from the server.
For remote operation of the pair of disk arrays on the remote side, check that the
states of disk array and link path are normal. Both the disk arrays on the local
side and remote side requires the function and license of
RemoteDataReplication/DisasterRecovery product.
Chapter 2 Message List
392
iSM13607: Specified disk type is not supported.
iSM13607: Specified drive type is not supported.
[Classification] ERROR
[Explanation] Specified disk or drive type is not supported.
This message is output on Windows system.
[Measures] Check the formats of the specified disk and connected device and retry command
execution.
Partition disk with the GPT (GUID Partition Table) format cannot be used.
iSM13608: Specified partition has already
mounted.
[Classification] ERROR
[Explanation] Specified partition has already been mounted.
This message is output on Windows system.
[Measures] Check the specified partition and re-execute.
iSM13609: Access of specified disk was refused.
[Classification] ERROR
[Explanation] Access to the disk is refused.
This message is output on Windows system.
[Measures] If there is any application accessing the specified disk, terminate the application,
and then re-execute. Refer to the description on the unmount operation for the
“Data Replication User’s Manual (Installation and Operation Guide for
Windows)”.
Chapter 2 Message List
393
iSM13610: Illegal drive number is specified.
[Classification] ERROR
[Explanation] The specified disk number is illegal.
This message is output on Windows system.
[Measures] Specify a correct value.
iSM13611: RemoteDataReplication/Disaster
Recovery is not supported.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] RemoteDataReplication/DisasterRecovery function is not supported.
Or, software supporting the RemoteDataReplication/DisasterRecovery function
is not installed.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check that the disk array supports of RemoteDataReplication/DisasterRecovery
function. Prepare ReplicationControl/DisasterRecovery software and install it.
Chapter 2 Message List
394
iSM13612: Specified ATgroup is empty.
ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The specified AT-group does not have any registered pair.
aaa...a : AT-group name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] For operation of an AT-group, a pair must be registered in advance.
iSM13613: Specified volume does not have
signature. volume=<aaa...a>
[Classification] ERROR
[Explanation] The signature information of the specified disk does not exist.
This message is output on Windows system.
aaa...a : Physical disk number
[Measures] Specify a correct value.
Chapter 2 Message List
395
iSM13614: Failed to read signature.
iSM13614: Failed to read signature.
volume=<aaa...a>
[Classification] ERROR
[Explanation] The disk signature information could not be read.
aaa...a : Physical disk number
[Measures] If a message is output immediately before this message, take measures according
to the message. If no message is output immediately before this message,
check that no fault occurs on the volume and that it is readable, and then retry
processing.
iSM13615: Failed to read signature map file.
errno=<aaa>
[Classification] ERROR
[Explanation] The signature map file could not be read.
This message is output on Windows system.
aaa : Error number
[Measures] Take measures according to the message output immediately before this
message.
Chapter 2 Message List
396
iSM13616: ATgroup cannot be registered any
more.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] No more AT-group can be registered.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] No more AT-group can be registered because the number of registered
AT-groups has already reached the maximum number of AT-groups that can be
registered to the disk array.
iSM13617: Illegal ATgroup name. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The value specified as an AT-group name is invalid.
aaa...a : Specified value
bbb...b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a valid value. Characters other than alphanumeric characters, hyphen
(-), and slush (/) cannot be used for an AT-group name.
Chapter 2 Message List
397
iSM13618: Specified volume does not exist in
signature map file. volume=<aaa...a>
[Classification] ERROR
[Explanation] The specified disk does not exist in the signature map file.
This message is output on Windows system.
aaa...a : Physical disk number
[Measures] Specify a correct value.
iSM13619: Writing signature failed.
iSM13619: Writing signature failed.
volume=<aaa...a>
[Classification] ERROR
[Explanation] The signature could not be written into the signature map file.
This message is output on Windows system.
aaa...a : Physical disk number
[Measures] Take measures according to the message output immediately before this
message.
Chapter 2 Message List
398
iSM13623: Signature file access has failed.
filename=<aaa...a> errno=<bbb>
[Classification] ERROR
[Explanation] Access to the signature map file could not be made.
This message is output on Windows system.
aaa...a : File name
bbb : Error number
[Measures] Take measures according to the message output immediately before this
message.
iSM13624: Specified volume has no mount point.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] The specified volume has no mount point (drive letter or NTFS folder name).
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] The volume should have only one mount point (drive letter or NTFS folder
name). Check the volume status and operation procedures and re-execute.
Chapter 2 Message List
399
iSM13625: Specified volume has more than one
mount point.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] The specified volume has multiple mount points (drive letter or NTFS folder
name).
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] The volume should have only one mount point (drive letter or NTFS folder
name). Check the volume status and operation procedures and re-execute. Note
that you can delete the mount point set to the volume by using the /D option for
the MOUNTVOL command.
iSM13626: Signature file format is illegal.
filename=<aaa...a>
[Classification] ERROR
[Explanation] The signature map file is in illegal format.
This message is output on Windows system.
aaa...a : File name
[Measures] Specify a correct signature map file.
Chapter 2 Message List
400
iSM13627: Specified volume’s signature does
not exist in file. filename=<aaa...a>
[Classification] ERROR
[Explanation] The signature information of the specified disk does not exist in the signature
map file.
This message is output on Windows system.
aaa...a : File name
[Measures] Specify a correct value.
iSM13629: Too long file name is specified.
[Classification] ERROR
[Explanation] The specified file name is too long.
This message is output on Windows system.
[Measures] Specify a correct signature map file. If the current signature map file is correct,
change the file name.
iSM13630: Specified disk is read only.
[Classification] ERROR
[Explanation] Specified disk is read only. Write operation is not executes.
This message is output on Windows system.
[Measures] Change the RV access from the Replication Manager, or select a
read/write-enable disk.
Chapter 2 Message List
401
iSM13631: Failed to mount.
[Classification] ERROR
[Explanation] Failed to mount.
This message is output on Windows system.
[Measures] Check the message displayed immediately before to handle it.
iSM13632: Failed to umount.
[Classification] ERROR
[Explanation] Failed to unmount.
This message is output on Windows system.
[Measures] Check the message displayed immediately before to handle it.
iSM13633: Failed to flush.
[Classification] ERROR
[Explanation] Failed to execute buffer-flush for the file system.
This message is output on Windows system.
[Measures] Check the message displayed immediately before to handle it.
Chapter 2 Message List
402
iSM13634: Failed to set drive letter. (<aaa...a>)
iSM13634: Failed to set mount point. (<bbb...b>)
[Classification] ERROR
[Explanation] The drive letter or the NTFS folder mount point could not be set.
This message is output on Windows system.
aaa...a : Drive letters
bbb...b : Path
[Measures] Take measures according to the message output immediately before this
message.
iSM13635: Failed to reset drive letter. (<aaa...a>)
iSM13635: Failed to reset mount point.
(<bbb...b>)
[Classification] ERROR
[Explanation] The drive letter or the NTFS folder mount point could not be canceled.
This message is output on Windows system.
aaa...a : Drive letter
bbb...b : Path
[Measures] Take measures according to the message output immediately before this
message.
Chapter 2 Message List
403
iSM13636: Failed to initialize signature.
iSM13636: Failed to initialize signature.
volume=<aaa...a>
[Classification] ERROR
[Explanation] The disk signature information could not be initialized.
This message is output on Windows system.
aaa...a : Physical disk number
[Measures] Take measures according to the message output immediately before this
message.
iSM13637: Specified path (<aaa...a>) is not
correct directory.
[Classification] ERROR
[Explanation] The volume is not mounted onto the specified mount point (drive letter or NTFS
folder name). Or, the mount point volume name does not match the mount point.
aaa...a : Mount point (drive letter or NTFS folder name)
[Measures] Check the correspondence between the specified mount point volume name and
mount point, and re-execute the command.
Re-create the volume list if a mount point volume name or mount point status
does not match those in the volume list.
iSM13638: This OS version does not support
specified function.
[Classification] ERROR
[Explanation] Specified option cannot be used on this OS.
This message is output on Windows system.
[Measures] Check the target OS version.
Chapter 2 Message List
404
iSM13639: Specified path is not normal status.
[Classification] ERROR
[Explanation] File or directory cannot be read.
This message is output on Windows system.
[Measures] Check that the file or directory exists or access to the volume is permitted, and
retry command execution.
iSM13640: This iSM/Server version does not
support necessary function.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
iSM13640: This iSM/Server version does not
support necessary function for
<ccc...c>.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] There is a function that is not supported by the iSM server in use.
aaa...a : Process number
bbb…b : Detailed information (This code is not disorder reason but a
value for maintenance.)
ccc…c : Function name
RemoteDataReplication : There is a function that is not
supported for the pair of
RemoteDataReplication.
[Measures] Check the version of the iSM server.
If the version of the iSM server is older than that of ReplicationControl, upgrade
the version of the iSM server.
Chapter 2 Message List
405
iSM13641: Firmware does not support
necessary function.
iSM13641: Firmware does not support <aaa...a>
function.
[Classification] ERROR
[Explanation] Functions of firmware necessary are not supported.
aaa...a : Function name
signature : Signature function
separate(immediate) : Separate (Quick Replicate) function
separate(RDR immediate) : Separate (Quick Replicate) function
of RemoteDataReplication
restore(rv-protection) : Restore (protect) function
[Measures] Check for the target product, and update it.
iSM13642: Popen (ps command) has failed.
[Classification] ERROR
[Explanation] The I/O function of a pipe using the ps command could not be performed.
This message is output on UNIX system.
[Measures] Re-execute the command.
iSM13644: Failed to scan devices.
[Classification] ERROR
[Explanation] Failed to scan the device.
This message is output on Windows system.
[Measures] Check that there is no abnormality in the system and re-execute.
Chapter 2 Message List
406
iSM13645: Target pair cannot be registered in
specified ATgroup. MV=<aaa...a>
RV=<aaa...a>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
iSM13645: Target pair cannot be registered in
specified ATgroup. ATG=<bbb... b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
[Classification] ERROR
[Explanation] The specified pair cannot be registered in the AT-group.
To register a pair in an AT-group, the following conditions are required:
- The AT-group sync state is separated (Separated), failure separation (Fault),
or no pair registered (Invalid).
- The pair sync state is separated (separated), forced separate (cancel), or
failure separate (fault).
- The configuration of the pair must be RDR configuration. RV in RDR
configuration paired with MV must be only one.
- MV must be the top (PV) in relation with the related pairs, and it must not be
paired with another MV as RV.
- Every MV of RDR configuration within the AT-group must belong to the
same disk array.
- Every RV of RDR configuration within the AT-group must belong to the
same disk array.
- The number of pairs registered in the AT-group must not exceed the limit
(disk array specifications).
aaa...a : Volume name
bbb...b : AT-group name
ccc...c : Process number
ddd…d : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check the state of the AT-group, the state of the specified pair, and configuration
of the pair, and then re-execute the command. If the number of pairs registered
in the AT-group has already reached the limit, a new pair cannot be registered
any more.
Chapter 2 Message List
407
iSM13646: Specified mv volume is mounted.
path=<aaa...a>
[Classification] ERROR
[Explanation] The MV has been mounted.
This message is output on UNIX system.
aaa...a : Path name of MV (special file name, volume path name, etc.)
[Measures] Unmount the MV, and then re-execute the command.
iSM13647: These targets are not replicating now.
MV:<aaa...a> RV:<aaa...a>
[Classification] ERROR
[Explanation] Specified pair is not in the replication status.
aaa...a : Volume name
[Measures] Check the pair operation status and re-execute
iSM13648: These targets are not separating now.
MV:<aaa...a> RV:<aaa...a>
[Classification] ERROR
[Explanation] Specified pair is not in the separation status.
aaa...a : Volume name
[Measures] Check the specified pair operation status and re-execute
Chapter 2 Message List
408
iSM13649: These targets are not restoring now.
MV:<aaa...a> RV:<aaa...a>
[Classification] ERROR
[Explanation] Specified pair is not in the restoration status.
aaa...a : Volume name
[Measures] Check the specified pair operation status and re-execute
iSM13650: Target pair is a member of ATgroup.
MV=<aaa...a> RV=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The specified pair is already registered in the AT-group.
Pairs registered in an AT-group are not individually manipulable.
RDR configuration cannot be set additionally to pairs registered in an AT-group.
Pairs registered in an AT-group cannot be unpaired or forcibly unpaired.
aaa...a : Volume name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check the specified volume, and retry processing.
Or, specify the AT-group, and perform operation by manipulating it.
Otherwise, delete the pair registration from the AT-group, and then unpair or
forcibly unpair the target.
Chapter 2 Message List
409
iSM13651: Target pair is already registered in
other ATgroup. MV=<aaa...a>
RV=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
iSM13651: Target pair is already registered in
specified ATgroup. MV=<aaa...a>
RV=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The specified pair is already registered in another AT-group. A pair cannot be
registered in multiple AT-groups at the same time.
aaa...a : Volume name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check the specified volume, and then retry processing.
Or, unpair the target from the AT-group, and re-execute the command.
iSM13652: Target pair is not registered in
specified ATgroup. MV=<aaa...a>
RV=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The specified pair is not registered in the AT-group.
aaa...a : Volume name
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check the specified AT-group or volume, and retry processing.
Chapter 2 Message List
410
iSM13653: Illegal mode type. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The value specified in the mode option of the Restore command is illegal.
aaa...a : Specified value
bbb...b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a correct value.
iSM13654: Illegal rvuse type. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The value specified in the rvuse option of the Separate command is illegal.
aaa...a : Specified value
bbb...b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a correct value.
Chapter 2 Message List
411
iSM13655: Illegal condition type. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The value specified in the cond option of the Wait command is illegal.
aaa...a : Specified value
bbb...b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a correct value.
iSM13656: Illegal value of -interval [second].
(<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The value specified in the interval option of the Wait command is illegal.
aaa...a : Specified value
bbb...b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a correct value.
Chapter 2 Message List
412
iSM13657: Illegal value of -limit [second].
(<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The value specified in the limit option of the Wait command is illegal.
aaa...a : Specified value
bbb...b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a correct value.
iSM13658: Wait command has terminated
because it has reached the time limit
which is specified by the limit option.
(<aaa> sec)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The time limit specified in the limit option of the wait command arrived, and the
wait process was discontinued.
aaa : Time limit
bbb...b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Re-execute the Wait command.
Chapter 2 Message List
413
iSM13659: Specified targets are not ready.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
iSM13659: Specified targets are not available.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] Specified volume is unavailable.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] The volume is specified under the Read Only, Not Ready, or Not Available
status. Check status of volume and retry command execution.
Chapter 2 Message List
414
iSM13660: Replicate command has terminated
because “activity status” is changed
by other process.
iSM13660: Replicate command has terminated
because “ATgroup Sync State” is
changed by other process.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] Activity status of a pair has changed to status other than Replicate during waiting
process for completion of replication. The replication command has terminated
waiting for completion of replication. Or, the waiting is terminated because the
AT-group sync state changed to another state than replicate synchronous
(Rpl/sync) from replicate execution (Rpl/exec) during waiting process for
completion of replication.
aaa...a : Process number
bbb…b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] If the target is a pair, another process may have manipulated this pair. If it is an
AT-group, this AT-group may have had its sync state manipulated by another
process or it may have failure. Check status of pair or AT-group. If
replication is required, retry executing the replication command.
Chapter 2 Message List
415
iSM13661: Restore command has terminated
because “activity status” is changed
by other process.
iSM13661: Restore command has terminated
because “ATgroup Sync State” is
changed by other process.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] Activity status of a pair has changed to status other than Restore during waiting
process for completion of restoration. The restore command has terminated
waiting for completion of restoration. Or, the waiting is terminated because the
AT-group sync state changed to another state than separated (Separated), which
is concurrent with completion of restoration, from restore execution (Rst/exec)
during waiting process for completion of restoration.
[Measures] If the target is a pair, another process may have manipulated this pair. If it is an
AT-group, this AT-group may have had its sync state manipulated by another
process or it may have a fault. Check status of pair or AT-group. If
restoration is required, retry executing the restore command.
Chapter 2 Message List
416
iSM13662: Separate command has terminated
because “activity status” is changed
by other process.
iSM13662: Separate command has terminated
because “ATgroup Sync State” is
changed by other process.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] Activity status of a pair has changed to status other than Separate during waiting
process for completion of separation. The separate command has terminated
waiting for completion of separation. Or, the waiting is terminated because the
AT-group sync state changed to another state than separated (Separated) from
separate execution (Sep/exec) during waiting process for completion of
separation.
aaa...a : Process number
bbb…b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] If the target is a pair, another process may have manipulated this pair. If it is an
AT-group, this AT-group may have had its sync state manipulated by another
process or it may have a fault. Check the state of the pair or the AT-group, and
separate it by Forced Separate if necessary. If it is required that the consistency
of the data on the RV should be kept when the target is separated, you have to do
it all over again from replication.
Chapter 2 Message List
417
iSM13663: The processing of waiting has
terminated because “separate diff” or
“copy diff” does not decrease in the
specified time. (<aaa> sec)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The waiting process for completion of replication, restoration, or separation has
been terminated before completion because the copy difference of the pair or the
differential quantity volume of the AT-group did not decrease in the specified
time.
aaa : Specified value
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] The possible causes are a link failure of the disk array and delay of copy
processing or data transfer due to heavy I/O load or another factor. Check the
state of the disk array and AT-group.
Chapter 2 Message List
418
iSM13664: Wait command has terminated
because “ATgroup Sync State” is
changed by other process.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] The waiting process for completion of synchronization or separation has been
terminated before completion because an error in the AT-group sync state as
described below has been detected.
- An error has been detected in the link path of the AT-group.
Normal link path does not exist any more.
Differential quantity of volume of the AT-group has become an
invalid value.
- The AT-group sync state has changed to:
Invalid state with no pair registered (Invalid)
Failure separation (Fault)
Restore suspend (Rst/suspend)
Replicate suspend (Rpl/suspend)
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] This AT-group may have had its sync state manipulated by another process or it
may have a fault. Check the state of the AT-group, and separate it by Forced
Separate if necessary. If it is required that the consistency of the data on the RV
should be kept when the target is separated, you have to do it all over again from
replication.
Chapter 2 Message List
419
iSM13669: SnapControl is not installed.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] SnapControl has not been installed.
aaa...a : Process number
bbb…b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Install SnapControl.
iSM13670: ReplicationControl is not installed.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] ReplicationControl has not been installed.
aaa...a : Process number
bbb…b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Install ReplicationControl.
iSM13671: License for DynamicSnapVolume is
locked.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] The license for DynamicSnapVolume has not been unlocked.
aaa...a : Process number
bbb…b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Unlock the license for disk array.
Chapter 2 Message List
420
iSM13672: DynamicSnapVolume is not
supported.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] DynamicSnapVolume is not supported.
aaa...a : Process number
bbb…b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check the support state of the disk array.
iSM13673: Specified attribute (<aaa...a>) does
not match the attribute of ATgroup.
ATG=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
[Classification] ERROR
[Explanation] The specified attribute does not match the attribute of the AT-group. To
specify the atomic-break mode or copy mode at restart of replication, the
attribute must match the value specified at start of replication.
aaa...a : Specified attribute value
bbb…b : AT-group name
ccc…c : Process number
ddd…d : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify the same value for the atomic-break mode or copy mode as the value
specified at start of replication. Otherwise, omit specification of the
atomic-break mode or copy mode, and then re-execute the command.
Chapter 2 Message List
421
iSM13674: Specified volume is used by snapshot
function. <aaa...a>:<bbb...b >
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
[Classification] ERROR
[Explanation] Snapshot operation is taking place in the specified volume.
aaa...a : Character string indicating MV or RV
MV : MV volume
RV : RV volume
bbb...b : Volume name (logical disk name)
ccc...c : Process number
ddd...d : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the snapshot status of specified volume and re-execute. Replication and
restore operations cannot be performed while you are restoring snapshot to MV.
You can perform restore operation only when all MV-related snapshots are
inactive (snap/inactive).
iSM13675: Failed to umount of metafile volume.
[Classification] ERROR
[Explanation] Unmounting of metafile volume failed.
[Measures] Other program is using the applicable volume. Terminate the program, execute
iSMrc_umount, and then disconnect the volume.
Chapter 2 Message List
422
iSM13676: Failed to sql server connection.
[Classification] ERROR
[Explanation] Connection of Microsoft SQL Server 2000 failed.
[Measures] Microsoft SQL Server 2000 service may have not started. Check that the
service started and retry command execution. Or, if a user ID is specified upon
execution of a command, the specified user ID and password are used for
connecting to Microsoft SQL Server 2000. However, if a user ID is omitted,
user name and password of Windows login account are used for connection.
Check that the user ID and password are correct, and then retry command
execution.
iSM13677: Backup set name is too long.
(<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The specified backup set name is too long.
aaa...a : Specified value
bbb…b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Enter the backup set name correctly and retry the processing.
iSM13678: Description is too long. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] Description for the specified backup set is too long.
aaa...a : Specified value
bbb…b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Enter description for the backup set correctly and retry the processing.
Chapter 2 Message List
423
iSM13679: Illegal remod type. (<aaa...a>)
[Classification] ERROR
[Explanation] A value specified for -remod option is invalid.
aaa...a : Specified value
[Measures] Specify a valid value.
iSM13680: Illegal refile name. (<aaa...a>)
[Classification] ERROR
[Explanation] A value specified for -refile option is invalid.
aaa...a : Specified value
[Measures] Specify a valid value.
iSM13681: Specified volume differs from
database volume.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] Volume specified by MV or BV is different than a volume in which a target
database has been created.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a volume in which a database has been created to MV or BV.
Chapter 2 Message List
424
iSM13682: Failed to VDI initialization.
[Classification] ERROR
[Explanation] Initial process of VDI failed.
[Measures] Check that VDI is available in given environment, and then retry command
execution.
iSM13683: No authority to access database.
[Classification] ERROR
[Explanation] No authority to access database is given.
[Measures] Check that authority to access database is given. Check that database is not
under restoration or under verification.
iSM13684: Failed to get database name list.
[Classification] ERROR
[Explanation] Failed in obtaining database name list.
[Measures] Check that authority to access database is given. Check that database is not
under restoration or under verification.
iSM13685: Failed to sql connection initialization.
[Classification] ERROR
[Explanation] Failed in initializing SQL connection.
[Measures] Check the environment allows use of ODBC, and then retry command execution.
Chapter 2 Message List
425
iSM13686: Failed to metafile (<aaa...a>) creation.
[Classification] ERROR
[Explanation] Failed in creating metafile.
aaa...a : File name
[Measures] Check that specified metafile is correct and retry command execution.
iSM13687: Metafile(<aaa...a>) is not found.
[Classification] ERROR
[Explanation] Specified metafile is not found.
aaa...a : File name
[Measures] Check that specified metafile is correct and retry command execution.
iSM13688: Failed to metafile(<aaa...a>) open.
[Classification] ERROR
[Explanation] Failed in opening metafile.
aaa...a : File name
[Measures] Check that specified metafile is correct and retry command execution.
iSM13689: Failed to snapshot execution.
code=<aaa...a>
[Classification] ERROR
[Explanation] Failed in executing snapshot.
aaa...a : Error message number notified from Microsoft SQL Server 2000
(decimal)
[Measures] For error message number, refer to Microsoft SQL Server 2000 Books online.
Check error log of Microsoft SQL Server 2000, remove cause of fault and then
retry command execution.
Chapter 2 Message List
426
iSM13690: Failed to sql command execution.
[Classification] ERROR
[Explanation] Failed in SQL command.
[Measures] Check error log of Microsoft SQL Server 2000, remove cause of fault and then
retry command execution.
iSM13691: Dbname does not exist in SQL
server.
[Classification] ERROR
[Explanation] Database name does not exist in Microsoft SQL Server 2000.
[Measures] Check that database name is correct, and then retry command execution.
iSM13692: Specified volume has multiple
databases.
[Classification] ERROR
[Explanation] Two or more databases exist in one volume. Or, the target volume has an
unspecified database.
[Measures] Create only one database on one volume. Or, specify each and every database
on the volume for executing snapshot backup or snapshot restore.
iSM13693: Metafile is existing in the same
volume as the database.
[Classification] ERROR
[Explanation] A metafile exist in the same volume that is used by database.
[Measures] Specify a metafile in different volume than that used by database.
Chapter 2 Message List
427
iSM13694: Database (<aaa...a>) is being used in
another process.
[Classification] ERROR
[Explanation] Database is used by other process.
aaa...a : Database name
[Measures] Check that other process is not using the database and then retry command
execution.
iSM13695: Failed to detach database.
[Classification] ERROR
[Explanation] Detaching database failed.
[Measures] Check that detaching database is allowed and then retry command execution.
iSM13696: Failed to get database volume from
metafile.
[Classification] ERROR
[Explanation] Obtaining volume from metafile failed.
[Measures] Check that metafile is correct and then retry command execution.
iSM13697: Not found database file.
[Classification] ERROR
[Explanation] Physical file in database is not found.
[Measures] Check that the physical file exists and then retry command execution.
Chapter 2 Message List
428
iSM13698: Database filename does not exist in
metafile.
[Classification] ERROR
[Explanation] File name of database does not exist in metafile.
[Measures] Check that specified file name indicates a physical file of database and then retry
command execution.
iSM13699: Number of move files are not equal to
metafile’s number.
[Classification] ERROR
[Explanation] The number of files specified by -move option is not the same as the number of
files in database.
[Measures] Check that the number of specified files is the same as the number of physical
files in database, and then retry command execution.
iSM13700: Failed to execute command.
iSM13700: Failed to execute command.
(mv=<aaa...a>, rv=<aaa...a>)
[Classification] ERROR
[Explanation] Command execution failed.
aaa...a : Volume name
[Measures] Take measures with reference to a message that was output immediately before
this message.
Chapter 2 Message List
429
iSM13701: ‘R/W permit’ mode cannot be set
when state is ‘rpl/sync’, ‘rpl/exec’,
‘rst/sync’, ‘rst/exec’ or ‘sep/exec’.
(code=<aaa...a>-<bbb...b>-<bbb...b>-
<bbb...b>)
[Classification] ERROR
[Explanation] R/W Permit mode cannot be specified because the system is under status of
replicated, executing replication, restored, executing restoration, or executing
separation.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] For specifying R/W, check that the system is under separated status and then
retry command execution.
iSM13702: Specified ‘Background copy level’ is
incorrect. (level=<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-
<ccc...c>)
[Classification] ERROR
[Explanation] Invalid value has been specified for copy level.
aaa...a : Specified values
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify correct value for copy level and then retry command execution.
Chapter 2 Message List
430
iSM13703: Failed to connect iSM/Server.
(code=<aaa...a>-<bbb...b>-<bbb...b>-
<bbb...b>)
[Classification] ERROR
[Explanation] Socket connection failed
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check status of iSM server.
iSM13704: The unexpected error has occurred in
iSM/Server. (code=<aaa...a>-
<bbb...b>-<bbb...b>-<bbb...b>)
[Classification] ERROR
[Explanation] An unexpected error occurred.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Abnormality was found in message from iSM server. Check status of iSM
server.
iSM13705: Receive data is incorrect. Data
mismatch may has occurred in
iSM/Server. (code=<aaa...a>-
<bbb...b>-<bbb...b>-<bbb...b>)
[Classification] ERROR
[Explanation] Received data is invalid. Data inconsistency may exist in server.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Abnormality was found in message from iSM server. Check status of iSM
server.
Chapter 2 Message List
431
iSM13706: No more RV can be paired with
specified MV. (code=<aaa...a>-
<bbb...b>-<bbb...b>-<bbb...b>)
[Classification] ERROR
[Explanation] Pair setting is unavailable because the number of pairs in specified MV exceeds
upper limit.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check status of specified MV, and then specify pairs correctly.
iSM13707: Specified RV has already paired with
other MV. (code=<aaa...a>-<bbb...b>-
<bbb...b>-<bbb...b>)
[Classification] ERROR
[Explanation] Pair setting is unavailable because specified RV has been specified for a pair
with other MV.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check status of specified RV, and then specify pairs correctly.
iSM13708: Specified pair will build loop
structure. (code=<aaa...a>-<bbb...b>-
<bbb...b>-<bbb...b>)
[Classification] ERROR
[Explanation] Specified volume results in loop structure of pairs
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify volume correctly so that it does not result in loop structure of pairs
Chapter 2 Message List
432
iSM13709: Conflict of volume list data has been
detected. (code=<aaa...a>-<bbb...b>-
<bbb...b>-<bbb...b>)
[Classification] ERROR
[Explanation] Inconsistency was found in volume list.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Create a volume list again.
iSM13710: Capacity of specified volumes does
not match. (code=<aaa...a>-<bbb...b>-
<bbb...b>-<bbb...b>)
[Classification] ERROR
[Explanation] Pair setting is not allowed because volume capacities are different from each
other.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check volume capacity.
iSM13711: OS type of specified volumes does
not match. (code=<aaa...a>-<bbb...b>-
<bbb...b>-<bbb...b>)
[Classification] ERROR
[Explanation] OS type of specified values does not match with each other.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check OS type.
Chapter 2 Message List
433
iSM13712: Some link paths which belong to
specified Disk Array are not normal
state. (code=<aaa...a>-<bbb...b>-
<bbb...b>-<bbb...b>)
[Classification] ERROR
[Explanation] An error has been detected in some link paths among disk arrays.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check link path status of disk array.
iSM13713: Specified Disk Array is not managed
by iSM. (code=<aaa...a>-<bbb...b>-
<bbb...b>-<bbb...b>)
[Classification] ERROR
[Explanation] Specified disk array is not under control of iSM.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check that specified disk array is under management of iSM.
Chapter 2 Message List
434
iSM13714: Disk Array includes specified volume
is not managed by iSM.
(code=<aaa...a>-<bbb...b>-<bbb...b>-
<bbb...b>)
[Classification] ERROR
[Explanation] Necessary information could not be obtained because the disk array including the
specified volume is not managed by iSM.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check that specified disk array is under management of iSM.
iSM13715: Disk Arrays managed by iSM do not
exist. (code=<aaa...a>-<bbb...b>-
<bbb...b>-<bbb...b>)
[Classification] ERROR
[Explanation] Specified disk array does not exist.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check disk array name and input a correct name.
iSM13716: State of specified Disk Array is not
‘freeze’. (code=<aaa...a>-<bbb...b>-
<bbb...b>-<bbb...b>)
[Classification] ERROR
[Explanation] Specified disk array is under “defreeze” status.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check the status of the disk array.
Chapter 2 Message List
435
iSM13717: Control path is not set to iSM/Server.
(code=<aaa...a>-<bbb...b>-<bbb...b>-
<bbb...b>)
[Classification] ERROR
[Explanation] I/O path for disk array is not specified to use iSM server (replication
management function).
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specified option is available only when I/O path for disk array is specified to use
iSM server (replication management function).
Check environment settings of ReplicationControl.
iSM13718: Specified Disk Array does not exist.
(code=<aaa...a>-<bbb...b>-<bbb...b>-
<bbb...b>)
[Classification] ERROR
[Explanation] Specified disk array does not exist.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check disk array name and then retry command execution.
iSM13719: Specified Disk Array name is too long.
(code=<aaa...a>-<bbb...b>-<bbb...b>-
<bbb...b>)
[Classification] ERROR
[Explanation] Specified disk array name is tool long.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Input a correct disk array name and then retry command execution.
Chapter 2 Message List
436
iSM13720: License for DynamicDataReplication/
RemoteDataReplication is locked.
(code=<aaa...a>-<bbb...b>-<bbb...b>-
<bbb...b>)
[Classification] ERROR
[Explanation] License for DynamicDataReplication or RemoteDataReplication is not unlocked.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Unlock the license of disk array.
iSM13721: DynamicDataReplication/Remote
DataReplication is not supported.
(code=<aaa...a>-<bbb...b>-<bbb...b>-
<bbb...b>)
[Classification] ERROR
[Explanation] DynamicDataReplication or RemoteDataReplication is not supported.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check supporting status of disk array.
iSM13722: Specified volume does not exist in
Logical disk list. (code=<aaa...a>-
<bbb...b>-<bbb...b>-<bbb...b>)
[Classification] ERROR
[Explanation] Specified volume does not exist in logical disk list.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check specified volume name and then retry command execution.
Chapter 2 Message List
437
iSM13723: State of Disk Array includes specified
volume is ‘monitoring stop’.
(code=<aaa...a>-<bbb...b>-<bbb...b>-
<bbb...b>)
[Classification] ERROR
[Explanation] Monitoring on disk array of specified volume has been stopped.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Start monitoring on disk array.
iSM13724: Failed to receive volume information.
(code=<aaa...a>-<bbb...b>-<bbb...b>-
<bbb...b>)
[Classification] ERROR
[Explanation] Obtaining volume information failed.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check specified volume name and then retry command execution.
Chapter 2 Message List
438
iSM13725: Disk Arrays can be available to
replication does not exist.
(code=<aaa...a>-<bbb...b>-<bbb...b>-
<bbb...b>)
[Classification] ERROR
[Explanation] Disk array to be monitored does not exist, or disk array applicable to data
replication function does not exist.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check that disk array is monitored, or that data replication function is available.
iSM13726: Volume information error has
detected in iSM/server.
(code=<aaa...a>-<bbb...b>-<bbb...b>-
<bbb...b>)
[Classification] ERROR
[Explanation] Volume information is invalid.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check status of iSM server and disk array.
Chapter 2 Message List
439
iSM13727: Attribute of specified volume is
‘<aaa...a>’. <bbb...b>:<ccc...c>
(code=<ddd...d>-<eee...e>-
<eee...e>-<eee...e>)
[Classification] ERROR
[Explanation] The following attributes are added to the specified volume.
aaa...a : Volume attribute
reserve: Volume with a reserve attribute (registered in a reserve
group)
BV: Volume with a BV attribute
SV: Volume with an SV attribute
LV: Volume with an LV attribute
SDV: Volume with an SDV attribute
bbb...b : Character string indicating MV or RV
MV: Volume with an MV attribute
RV: Volume with an RV attribute
ccc...c : Volume name (logical disk name)
ddd...d : Process number
eee...e : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] The specified volume cannot be specified as a pair.
iSM13728: Failed to execute command. (part of
targets)
[Classification] ERROR
[Explanation] Operations on some pairs failed.
[Measures] Check status of pairs with failed operation and then retry command execution.
Chapter 2 Message List
440
iSM13729: Failed to execute command. (all of
targets)
[Classification] ERROR
[Explanation] Operations on all pairs failed.
[Measures] Check status of pairs with failed operation and then retry command execution.
iSM13730: RV of specified pair has already
forced to be unpaired.
(code=<aaa...a>-<bbb...b>-<bbb...b>-
<bbb...b>)
[Classification] ERROR
[Explanation] RV of specified pair has already been unpaired forcibly.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check status of specified pairs.
iSM13731: Disk Array of specified pair are not
linked each other. (code=<aaa...a>-
<bbb...b>-<bbb...b>-<bbb...b>)
[Classification] ERROR
[Explanation] Specified volume does not allow pair setting.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check that operation is allowed for disk array of specified volume.
Chapter 2 Message List
441
iSM13732: Capacity of <aaa...a> license is
insufficient. (code=<bbb...b>-
<ccc...c>-<ccc...c>-<ccc...c>)
[Classification] ERROR
[Explanation] Licensed capacity is insufficient.
aaa...a : License name in question
DynamicDataReplication
RemoteDataReplication
RemoteDataReplication/DisasterRecovery
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Increase the licensed capacity and then retry command execution.
iSM13734: Specified MV has already paired with
other volume on same Disk Array as
RV. (code=<aaa...a>-<bbb...b>-
<bbb...b>-<bbb...b>)
[Classification] ERROR
[Explanation] Specified MV has already been paired as RV within the same disk.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check status of specified MV and specify pairs correctly.
Chapter 2 Message List
442
iSM13735: Specified RV has already paired with
other volume on same Disk Array as
MV. (code=<aaa...a>-<bbb...b>-
<bbb...b>-<bbb...b>)
[Classification] ERROR
[Explanation] Specified RV has already been paired as MV within the same disk.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check status of specified RV and specify pairs correctly.
iSM13736: Failed to open target-control volume
list data. (code=<aaa...a>-<bbb...b>-
<bbb...b>-<bbb...b>)
[Classification] ERROR
[Explanation] Opening of target-control volume list failed.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] A target-control volume list may be invalid. Create a target-control volume list
again.
iSM13737: Failed to close target-control volume
list data. (code=<aaa...a>-<bbb...b>-
<bbb...b>-<bbb...b>)
[Classification] ERROR
[Explanation] Closing of target-control volume list failed.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] A target-control volume list may be invalid. Create a target-control volume list
again.
Chapter 2 Message List
443
iSM13738: Target-control volume list data has
invalid data.
[Classification] ERROR
[Explanation] Target-control list contains invalid information.
[Measures] Create a target-control volume list again.
iSM13739: Control volume is not found.
[Classification] ERROR
[Explanation] Control volume is not found.
[Measures] Check that control volume definition file is described correctly, and then create a
target-control volume list again.
iSM13740: Failed to open control volume in
Diagnostic mode.
[Classification] ERROR
[Explanation] Control volume cannot be opened in Diagnostic mode.
[Measures] Check that LVM has not been activated on control volume or has not been
opened in Diagnostic mode by other application, and then retry command
execution.
Chapter 2 Message List
444
iSM13741: Failed to create socket.
(code=<aaa...a>-<bbb...b>-<ccc...c>-
<ddd...d>)
[Classification] ERROR
[Explanation] Socked creation failed.
aaa...a : Process number
bbb...b-ccc…c-ddd…d : Detailed information (This code is not disorder
reason but a value for maintenance.)
[Measures] With reference to error number indicated by ddd...d in detailed information,
remove cause of error and retry command execution.
iSM13742: Failed to send to iSM/Server.
(code=<aaa...a>-<bbb...b>-<bbb...b>-
<bbb...b>)
[Classification] ERROR
[Explanation] Message transmission to iSM server failed.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check status of communication with iSM server.
Chapter 2 Message List
445
iSM13743: Failed to receive from iSM/Server.
(code=<aaa...a>-<bbb...b>-<bbb...b>-
<bbb...b>)
[Classification] ERROR
[Explanation] Message reception from iSM server failed.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check status of communication with iSM server.
iSM13744: Specified <aaa...a> is duplicated.
(code=<bbb...b>-<ccc...c>-<ccc...c>-
<ccc...c>)
[Classification] ERROR
[Explanation] Specified volume exists in duplication.
aaa...a : Volume number
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check specified volume mane.
Chapter 2 Message List
446
iSM13745: Illegal value of port number. <aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-
<ccc...c>)
[Classification] ERROR
[Explanation] Invalid value has been specified for socket port number.
aaa...a : Socket port number
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a correct socket port number.
iSM13746: Illegal OS type. <aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-
<ccc...c>)
[Classification] ERROR
[Explanation] Invalid OS type has been specified for volume.
aaa...a : OS type
bbb...b : Process number
ccc...c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a correct OS type for volume.
iSM13747: Specified Disk Array does not have
link information. (code=<aaa...a>-
<bbb...b>-<bbb...b>-<bbb...b>)
[Classification] ERROR
[Explanation] Link information does not exist for specified disk array.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check a specified disk array name.
Chapter 2 Message List
447
iSM13748: Failed to <aaa...a>(<bbb...b>). drive
letter (<ccc...c>)
(code=<eee...e>-<fff...f>-<fff...f>-<fff...f
>)
iSM13748: Failed to <aaa...a>(<bbb...b>). mount
point volume (<ddd...d>)
(code=<eee...e>-<fff...f>-<fff...f>-<fff...f
>)
[Classification] ERROR
[Explanation] Operations on volume failed.
aaa...a : Executed Operations
replicate : Replicate
restore : Restore
unmount : Unmount
bbb...b : Volume Operations
mount : Mount volume
umount : Unmount volume
lock : Lock volume
unlock : Unlock volume
mountvol(p) : Delete mount point of volume and unmount
volume
ccc...c : Drive letter
ddd...d : Mount point volume name
eee...e : Process number
fff…f : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check the status of the volume on which operation failed, mount point volume
name, and the mount point status. Then, execute operation on the volume
again.
Chapter 2 Message List
448
iSM13749: Volume list data is locked by another
process.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] Volume list data has been created/modified by other process.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] After completion of a process, retry command execution.
iSM13750: Volume list data does not exist.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] Volume list data does not exist.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Create a volume list, and then retry command execution.
Chapter 2 Message List
449
iSM13751: Volume type is not ld.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] Specified volume type is not logical disk.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check a specified volume type. Operations linked with replication
management allow specifying logical disk name only.
iSM13752: Timeout error has occurred in
iSM/Server.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] Time-out occurred in process of iSM server.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Loads on iSM server may be too heavy. Check status of iSM server and retry
command execution.
Chapter 2 Message List
450
iSM13753: Disconnected from iSM/Server.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] Connection with iSM server was disconnected.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Operations of iSM server may have stopped. Check status of iSM server.
iSM13754: Replication function of iSM/Server is
not ready.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] Replication function of iSM/Server is being activated, and is not ready.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Wait a while and then retry command execution.
Chapter 2 Message List
451
iSM13755: Command issue to <aaa...a> failed.
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] Issuing operation command failed.
aaa...a : Volume that failed in issuing operation command (MV, RV, or
MV/RV)
bbb...b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Take measures with reference to a message that was output immediately after
this message.
iSM13761: Illegal bvflg type. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] Specified BV type is invalid.
aaa...a : Specified value
bbb...b : Process number
ccc...c : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Specify a correct value.
Chapter 2 Message List
452
iSM13762: Illegal svflg type. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] Specified SV type is invalid.
aaa...a : Specified value
bbb...b : Process number
ccc...c : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Specify a correct value.
iSM13763: SV is omitted.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] SV was omitted for BV related with multiple SVs.
aaa...a : Process number
bbb...b : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Specify SV and re-execute.
iSM13764: RV or SV is omitted.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] RV or SV was omitted for the volume (MV and BV) related with RV and SV.
aaa...a : Process number
bbb...b : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Specify RV or SV and re-execute.
Chapter 2 Message List
453
iSM13765: Replication and snapshot function are
mixed in specified pairs.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] The data replication function pair and snapshot function pair are both specified.
aaa...a : Process number
bbb...b : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] The data replication function pair and snapshot function pair cannot be both
specified as operation target. Review pair specification and re-execute.
iSM13766: Illegal option value was specified.
(<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] Specified option is invalid.
aaa...a : Specified value
bbb...b : Process number
ccc...c : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Specify a correct option.
Chapter 2 Message List
454
iSM13767: Illegal volume type is specified.
filename=<aaa...a> line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
[Classification] ERROR
[Explanation] Specified volume type is invalid.
aaa...a : File name
bbb...b : Number of lines
ccc...c : Process number
ddd...d : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Specify a correct volume type and re-execute.
iSM13768: Illegal option value was specified.
filename=<aaa...a> line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
[Classification] ERROR
[Explanation] Specified value is invalid.
aaa...a : File name
bbb...b : Number of lines
ccc...c : Process number
ddd...d : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Correct the file and re-execute.
Chapter 2 Message List
455
iSM13769: Specified volume does not match the
database volume.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] The volume specified for MV or BV does not match the volume containing the
target database.
aaa...a : Process number
bbb...b : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check whether the specified volume is correct and whether you have specified
the exact amount of volume and re-execute.
iSM13770: State of specified pair is invalid.
(state=<aaa...a>) [BV:<bbb...b>]
[SV:<ccc...c>]
(code=<ddd...d>-<eee...e>-<eee...e>-<
eee...e>)
[Classification] ERROR
[Explanation] Target pair status is invalid.
aaa...a : Target pair status
Not snap/active. : Snapshot is not established.
snap/deleting or rst/exec. : Snapshot is being deleted or
restored.
bbb...b : BV logical disk name
ccc...c : SV logical disk name
ddd...d : Process number
eee...e : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the specification and status of pair and re-execute.
Chapter 2 Message List
456
iSM13771: Specified volume is under restoration.
[BV:<aaa...a>]
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] Specified volume is being restored.
aaa...a : BV logical disk name
bbb...b : Process number
ccc...c : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the pair status and that restore is completed and re-execute.
iSM13772: The volume under deletion exists.
[BV:<aaa...a>]
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] The SV currently being deleted exists.
aaa...a : BV logical disk name
bbb...b : Process number
ccc...c : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the pair status and that deletion is completed and re-execute.
Chapter 2 Message List
457
iSM13773: Specified volume is linked from LV.
[{BV|SV}:<aaa...a>]
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] BV or SV is linked to LV.
aaa...a : BV or SV logical disk name
bbb...b : Process number
ccc...c : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the pair status, remove the link (unlink), and re-execute.
iSM13774: Specified volume is protected by SV
guard. [SV:<aaa...a>]
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] SV protection is specified for specified SV.
aaa...a : SV logical disk name
bbb...b : Process number
ccc...c : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the pair and SV statuses, deactivate the SV protection, and re-execute.
Chapter 2 Message List
458
iSM13775: Deleting snapshot has terminated
because "Snap State" is changed by
other process.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] Processing has terminated because the snapshot activity state changed from the
deletion state (snap/deleting) during snapshot deletion.
aaa...a : Process number
bbb...b : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Another process might operate the snapshot pair. Check the snapshot activity
state and re-execute.
iSM13776: Restoring snapshot has terminated
because "Snap State" is changed by
other process.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] Processing has terminated because the snapshot activity state changed from the
restore state (rst/exec) during snapshot restoring.
aaa...a : Process number
bbb...b : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Another process might operate the snapshot pair. Check the snapshot activity
state and re-execute.
Chapter 2 Message List
459
iSM13777: The volume linked from LV exists.
[BV:<aaa...a>]
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] Some SV paired with BV are linked.
aaa...a : BV logical disk name
bbb...b : Process number
ccc...c : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the pair status, remove the link connection to the volume (unlink), and
re-execute.
iSM13778: The volume of SV guard exists.
[SV:<aaa...a>]
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] SV protection is specified for an SV older than SV to be restored.
aaa...a : SV logical disk name
bbb...b : Process number
ccc...c : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the pair status and deactivate the SV protection if you do not need the
volume's snapshot. Then, re-execute.
Chapter 2 Message List
460
iSM13779: Function error has occurred.
function=<aaa...a> retcode=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
[Classification] ERROR
[Explanation] A function error has occurred.
aaa...a : Name of function in which an error occurred
bbb...b : Code value returned by the function (refer to the table below)
Code
value
Explanation
40 Failed in locking the volume.
41 Failed in unlocking the volume.
42 Failed in mounting the volume.
43 Failed in unmounting the volume.
44 Failed in canceling the drive letter.
45 Failed in setting the drive letter.
201 The specified volume is not BV.
202 The specified volume is not SV.
Other An unexpected error has occurred.
ccc...c : Process number
ddd...d : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the function name and code value returned by the function, remove the
error cause, and re-execute.
Chapter 2 Message List
461
iSM13780: Specified volume is used by
replication function. BV:<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] Replication is taking place in the specified BV.
aaa...a : BV logical disk name
bbb...b : Process number
ccc...c : Detail information (This code is not disorder reason but a value
for maintenance.)
[Measures] Check the replication status of specified BV and re-execute.
iSM13800: No such database name.
filename=<aaa...a> line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
[Classification] ERROR
[Explanation] Database name has not been specified in database operation file.
aaa...a : File name
bbb...b : Number of lines
ccc…c : Process number
ddd…d : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a database name.
Chapter 2 Message List
462
iSM13801: Illegal Option type is specified.
filename=<aaa...a> line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
[Classification] ERROR
[Explanation] Invalid value was specified for option type in database operation file.
aaa...a : File name
bbb...b : Number of lines
ccc…c : Process number
ddd…d : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a correct value for option type.
iSM13802: Database name is too long.
filename=<aaa...a> line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
[Classification] ERROR
[Explanation] Database name specified in database operation file is too long.
aaa...a : File name
bbb...b : Number of lines
ccc…c : Process number
ddd…d : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a database name within 128 characters (1-byte).
Chapter 2 Message List
463
iSM13803: User id is too long.
filename=<aaa...a> line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
[Classification] ERROR
[Explanation] User ID specified in database operation file is too long.
aaa...a : File name
bbb...b : Number of lines
ccc…c : Process number
ddd…d : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a user ID within 64 characters (1-byte).
iSM13804: Password is too long.
filename=<aaa...a> line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
[Classification] ERROR
[Explanation] Password specified in database operation file is too long.
aaa...a : File name
bbb...b : Number of lines
ccc…c : Process number
ddd…d : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a password within 64 characters (1-byte).
Chapter 2 Message List
464
iSM13805: Server name is too long.
filename=<aaa...a> line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
[Classification] ERROR
[Explanation] “computer name\instance name” specified in database operation file is too long.
aaa...a : File name
bbb...b : Number of lines
ccc…c : Process number
ddd…d : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a computer name within 255 characters (1-byte), and specify an instance
name within 16 characters (1-byte).
iSM13806: Backup set name is too long.
filename=<aaa...a> line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
[Classification] ERROR
[Explanation] Backup set name specified in database operation file is too long.
aaa...a : File name
bbb...b : Number of lines
ccc…c : Process number
ddd…d : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify the backup set name correctly and retry the processing.
Chapter 2 Message List
465
iSM13807: Description name is too long.
filename=<aaa...a> line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
[Classification] ERROR
[Explanation] Description for the backup set specified in database operation file is too long.
aaa...a : File name
bbb...b : Number of lines
ccc…c : Process number
ddd…d : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify the description for the backup set correctly and retry the processing.
iSM13808: Illegal remod type. filename=<aaa...a>
line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
[Classification] ERROR
[Explanation] Database return mode value specified in database operation file is invalid.
aaa...a : File name
bbb...b : Number of lines
ccc…c : Process number
ddd…d : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a correct value.
Chapter 2 Message List
466
iSM13809: Refile name is too long.
filename=<aaa...a> line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
[Classification] ERROR
[Explanation] Standby database file name specified in database operation file is too long.
aaa...a : File name
bbb...b : Number of lines
ccc…c : Process number
ddd…d : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify standby database file name within 256 characters (1-byte).
iSM13810: Specified option (<aaa...a>) is
duplicated. filename=<bbb...b>
line=<ccc...c>
(code=<ddd...d>-<eee...e>-<eee...e>-<
eee...e>)
[Classification] ERROR
[Explanation] Two or more database names or options are specified in one line of database
operation file.
aaa...a : Specified value
bbb...b : File name
ccc...c : Number of lines
ddd…d : Process number
eee…e : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify only one database name or option.
Chapter 2 Message List
467
iSM13811: OS file name is too long.
filename=<aaa...a> line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
[Classification] ERROR
[Explanation] Physical file name for -move option specified in database operation file is too
long.
aaa...a : File name
bbb...b : Number of lines
ccc…c : Process number
ddd…d : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify -move option physical file name within 1024 characters (1-byte).
iSM13812: Illegal control option. (<aaa...a>)
filename=<bbb...b> line=<ccc...c>
(code=<ddd...d>-<eee...e>-<eee...e>-<
eee...e>)
[Classification] ERROR
[Explanation] Option specified in database operation file is invalid.
aaa...a : Specified value
bbb...b : File name
ccc...c : Number of lines
ddd…d : Process number
eee…e : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] With reference to description of database operation file, specify a valid option
name.
Chapter 2 Message List
468
iSM13813: Options “pass” can not be omitted
are specified. filename=<aaa...a>
line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
[Classification] ERROR
[Explanation] Option “pass” has been omitted in file setting of database operation file.
aaa...a : File name
bbb...b : Number of lines
ccc…c : Process number
ddd…d : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify “pass” option also when specifying “uid” option.
iSM13814: Illegal combination of options. (input)
filename=<aaa...a> line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
[Classification] ERROR
[Explanation] Option “input” has been specified in database operation file.
aaa...a : File name
bbb...b : Number of lines
ccc…c : Process number
ddd…d : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Do not specify “input” option when specifying “uid” and “pass” options.
Chapter 2 Message List
469
iSM13815: Options “uid” can not be omitted are
specified. filename=<aaa...a>
line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
[Classification] ERROR
[Explanation] Option “uid” has been omitted in database operation file.
aaa...a : File name
bbb...b : Number of lines
ccc…c : Process number
ddd…d : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify “uid” option also when specifying “pass” option.
iSM13816: Options “remod” and set value
“standby” can not be omitted are
specified. filename=<aaa...a>
line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
[Classification] ERROR
[Explanation] Option “remod” has been omitted in database operation file.
aaa...a : File name
bbb...b : Number of lines
ccc…c : Process number
ddd…d : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify “remod” option and setting value “standby” also when specifying
“refile” option.
Chapter 2 Message List
470
iSM13817: Specified database name is
duplicated. filename=<aaa...a>
line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<
ddd...d>)
[Classification] ERROR
[Explanation] Specified database overlaps in database operation file.
aaa...a : File name
bbb...b : Number of lines
ccc…c : Process number
ddd…d : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a database uniquely.
iSM13818: Failed to metafolder (<aaa...a>)
creation.
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] Specified metadata storage folder cannot be created.
aaa...a : Folder name
bbb...b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check that specified folder name is correct, and then retry command execution.
Chapter 2 Message List
471
iSM13819: Insufficient database. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] Database that has not been specified exists.
aaa...a : Specified value
bbb...b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify all databases in volume.
iSM13820: Illegal server name. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] Value specified by “-server” option is invalid.
aaa...a : Server name
bbb...b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a name in a form of “computer name\instance name” or “computer
name\”.
Chapter 2 Message List
472
iSM13821: Illegal server name. (<aaa...a>)
filename=<bbb...b> line=<ccc...c>
(code=<ddd...d>-<eee...e>-<eee...e>-<
eee...e>)
[Classification] ERROR
[Explanation] Value specified by “-server” option is invalid.
aaa...a : Server name
bbb...b : File name
ccc...c : Number of lines
ddd...d : Process number
eee…e : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a name in a form of “computer name\instance name” or “computer
name\”.
iSM13822: Failed to get SQL server version.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] Obtaining version information of Microsoft SQL Server 2000 failed.
aaa...a : Process number
bbb…b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check that access to Microsoft SQL Server 2000 is authorized.
Chapter 2 Message List
473
iSM13823: No authority to access SQL server.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] Access to Microsoft SQL Server 2000 is not authorized.
aaa...a : Process number
bbb…b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check that access to Microsoft SQL Server 2000 is authorized.
iSM13824: Illegal SQL server version.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] Version of Microsoft SQL Server 2000 is earlier than ServicePack2.
aaa...a : Process number
bbb…b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Install ServicePack2 of Microsoft SQL Server 2000.
Chapter 2 Message List
474
iSM13825: Specified iopath is not supported.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] The requested function is not available under the specified I/O issue control that
is currently enabled.
I/O issue path control must be specified, or the setting must be changed.
aaa...a : Process number
bbb...b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify the I/O issue path control or change the setting, and then retry processing.
You can specify the I/O issue path control using the -iopath option, or using the
replication control option setting file on Windows or environment variable on
UNIX. For how to set the I/O issue path control, refer to “Operation Settings”
in the “Data Replication Command Reference”.
iSM13826: Illegal refile name. (<aaa...a>)
filename=<bbb...b> line=<ccc...c>
(code=<ddd...d>-<eee...e>-<eee...e>-<
eee...e>)
[Classification] ERROR
[Explanation] Standby database file name is too long.
aaa...a : Standby database file name
bbb...b : File name
ccc...c : Number of lines
ddd...d : Process number
eee…e : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify standby database file name within 256 characters (1-byte).
Chapter 2 Message List
475
iSM13827: User id is too long.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] User ID is too long.
aaa...a : Process number
bbb…b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify user ID within 64 characters (1-byte).
iSM13828: Password is too long.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] Password is too long.
aaa...a : Process number
bbb…b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify password within 64 characters (1-byte).
Chapter 2 Message List
476
iSM13829: Server name is too long.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] “computer name\instance name” is too long.
aaa...a : Process number
bbb…b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify a computer name within 255 characters (1-byte), and specify an instance
name within 16 characters (1-byte).
iSM13830: Refile name is too long.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] Standby database file name is too long.
aaa...a : Process number
bbb…b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify standby database file name within 256 characters (1-byte).
Chapter 2 Message List
477
iSM13831: Database already exist. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<
ccc...c>)
[Classification] ERROR
[Explanation] Specified database already exists.
aaa...a : Database name
bbb...b : Process number
ccc…c : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Detach specified database, and execute SQL command again.
iSM13832: Database name is too long.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] Specified database name is too long.
aaa...a : Process number
bbb…b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify database name within 128 characters (1-byte).
Chapter 2 Message List
478
iSM13833: Database operation file name is too
long.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] Specified database operation file name is too long.
aaa...a : Process number
bbb…b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify database operation file name within 128 characters (1-byte).
iSM13834: Metafile name is too long.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] Specified metafile name is too long.
aaa...a : Process number
bbb…b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify metafile name within 256 characters (1-byte).
Chapter 2 Message List
479
iSM13835: Metafolder name is too long.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] Specified metafile storing folder name is too long.
aaa...a : Process number
bbb…b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify metafile storing folder name within 256 characters (1-byte).
iSM13836: Number of database exceeds the limit
that can be specified.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<
bbb...b>)
[Classification] ERROR
[Explanation] The number of databases simultaneously operative exceeds specifiable upper
limit.
aaa...a : Process number
bbb…b : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Reduce the number of databases simultaneously operated.
Chapter 2 Message List
480
iSM14000 ∼
iSM14400: Information sense error :
info=<aaa...a>, status=failed
(<bbb...b>)
[Classification] INFO
[Explanation] It indicates that it failed in acquiring Disk Array information.
aaa...a : Command name
bbb...b : Detail of error
[Measures] If an error occurred (status=failed was output), configuration or settings of disk
array may have been changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
iSM14401: Configuration reserved. : Disk
Array=<aaa...a>, status=<bbb...b>
[Classification] INFO
[Explanation] It indicates that configuration setting started.
aaa...a : Disk array name
bbb...b : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the specified disk array may be
under configuration setting by other configuration setting software. After
terminating all the configuration setting software, execute again.
Chapter 2 Message List
481
iSM14402: Configuration released. : Disk
Array=<aaa...a>, status=<bbb...b>
[Classification] INFO
[Explanation] It indicates that configuration setting completed.
aaa...a : Disk array name
bbb...b : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] An error may have occurred on the disk array or the control path. Remove the
cause of the error, disconnect the iSM client from which configuration setting
was made, and connect the iSM client again.
iSM14403: LD bind : LDN=<aaaa>h, <aaaa>h...,
RANK=<bb>h, <bb>h..., PDG=<cc>h,
status=<ddd...d>
[Classification] INFO
[Explanation] It indicates that the binding of Logical Disk was executed.
aaaa : Logical disk number
bb : RANK number
cc : PD group number
ddd...d : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
482
iSM14404: LD unbind : LDN=<aaaa>h, <aaaa>h...,
status=<bbb...b>
[Classification] INFO
[Explanation] It indicates that the unbinding of Logical Disk was executed.
aaaa : Logical disk number
bbb...b : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
iSM14405: RANK bind : RANK=<aa>h,
PDN=<bb>h, <bb>h..., PDG=<cc>h,
Time=<dd>, RAID=<ee>,
status=<fff...f>
[Classification] INFO
[Explanation] It indicates that the binding of RANK was executed.
aa : RANK number
bb : Physical disk number
cc : PD group number
dd : Rebuild time
ee : RAID type
fff...f : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
483
iSM14406: RANK unbind : RANK=<aa>h, <aa>h...,
PDG=<bb>h, status=<ccc...c>
[Classification] INFO
[Explanation] It indicates that the unbinding of RANK was executed.
aa : RANK number
bb : PD group number
ccc...c : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
iSM14407: Dynamic capacity expansion :
RANK=<aa>h, PDN=<bb>h,
PDG=<cc>h , Time=<dd>,
status=<eee...e>
[Classification] INFO
[Explanation] It indicates that the expansion of RANK was executed.
aa : RANK number
bb : Physical disk number
cc : PD group number
dd : Expansion time
eee...e : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
484
iSM14408: SPARE bind : PDN=<aa>h, <aa>h...,
PDG=<bb>h, status=<ccc...c>
[Classification] INFO
[Explanation] It indicates that the binding of SPARE was executed.
aa : Physical disk number
bb : PD group number
ccc...c : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
iSM14409: SPARE unbind : PDN=<aa>h,
<aa>h..., PDG=<bb>h,
status=<ccc...c>
[Classification] INFO
[Explanation] It indicates that the unbinding of SPARE was executed.
aa : Physical disk number
bb : PD group number
ccc...c : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
485
iSM14410: Set ownership : LDN=<aaaa>h,
<aaaa>h..., <bbbb>, status=<ccc...c>
[Classification] INFO
[Explanation] It indicates that the ownership of Logical Disk was set.
aaaa : Logical disk number
bbbb : Controller on which the ownership to be set (CNT0 or CNT1)
ccc...c : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
iSM14411: Cross call : mode=<aaa>,
status=<bbb...b>
[Classification] INFO
[Explanation] It indicates that ON/OFF of Cross call was set.
aaa : on, off
bbb...b : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
486
iSM14412: Set Disk Array time : <aaa...a>, Disk
Array=<bbb...b>, status=<ccc...c>
[Classification] INFO
[Explanation] It indicates that the date and time in the Disk Array was set.
aaa...a : date, time. Example (Thu May 24 14:03:01 JST 2001)
bbb...b : Target disk array name
ccc...c : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), invalid date and time may be
set. Check the set values and execute again.
iSM14413: Rebuild(maintenance) : RANK=<aa>h,
PDN=<bb>h, PDG=<cc>h, Time=<dd>,
status=<eee...e>
[Classification] INFO
[Explanation] It indicates that rebuilding to specified physical disk has been started.
aa : RANK number
bb : Physical disk number
cc : PD group number
dd : Rebuild time
eee...e : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
487
iSM14414: Forced Reduce(maintenance) :
RANK=<aa>h, PDN=<bb>h,
PDG=<cc>h, status=<ddd...d>
[Classification] INFO
[Explanation] It indicates that forced reduce was instructed to specified physical disk.
aa : RANK number
bb : Physical disk number
cc : PD group number
ddd...d : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
iSM14415: Preventive Reduce(maintenance) :
RANK=<aa>h, PDN=<bb>h,
PDG=<cc>h, status=<ddd...d>
[Classification] INFO
[Explanation] It indicates that preventive replacement was instructed to specified physical disk.
aa : RANK number
bb : Physical disk number
cc : PD group number
ddd...d : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
488
iSM14416: SPARE Rebuild(maintenance) :
RANK=<aa>h, PDN=<bb>h,
PDG=<cc>h, Time=<dd>,
status=<eee...e>
[Classification] INFO
[Explanation] It indicates that start of rebuilding using SPARE was instructed to specified
physical disk.
aa : RANK number
bb : Physical disk number
cc : PD group number
dd : Rebuild time
eee...e : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
iSM14417: Set Rebuild time(maintenance) :
RANK=<aa>h, PDG=<bb>h,
Time=<cc>h, status=<ddd...d>
[Classification] INFO
[Explanation] It indicates that rebuild time was changed for the physical disk under rebuilding
process.
aa : RANK number
bb : PD group number
cc : Rebuild time
ddd...d : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
489
iSM14418: Auto repair mode : mode=<aaa>,
status=<bbb...b>
[Classification] INFO
[Explanation] It indicates that ON/OFF of the auto repair was set.
aaa : on, off
bbb...b : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
iSM14419: Temp. sense interval(maintenance) :
interval=<aaaaa>, status=<bbb...b>
[Classification] INFO
[Explanation] It indicates that temperature monitoring interval was set.
aaaaa : Temperature monitoring interval
bbb...b : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), invalid temperature monitoring
interval may be set. Check the set value and execute again.
Chapter 2 Message List
490
iSM14420: FW download(maintenance) :
resource=<aa>, PDG=<bb>h,
number=<cc>h, <cc>h...,
status=<ddd...d>
[Classification] INFO
[Explanation] It indicates that firmware downloading was executed.
aa : Subjected resource
PD : Physical disk
HD : Host director
DE : Disk enclosure
SVP : Service processor
bb : PD group number (Valid only when the subjected resource is a
PD.)
cc : Resource number or all
ddd...d : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), check whether the F/W file or
the state or subjected resource is normal.
iSM14421: Disk Array log init(maintenance) :
status=<aaa...a>
[Classification] INFO
[Explanation] It indicates that the initialization of internal log of Disk Array was executed.
aaa...a : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
491
iSM14422: Media error list init(maintenance) :
RANK=<aa>h, PDG=<bb>h,
status=<ccc...c>
[Classification] INFO
[Explanation] It indicates that the Media error list within Disk Array was initialized.
aa : RANK number
bb : PD group number
ccc...c : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
iSM14423: PD recovery report
init(maintenance) : status=<aaa...a>
[Classification] INFO
[Explanation] It indicates that the PD recovery report within Disk Array was initialized.
aaa...a : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
492
iSM14424: Set SPARE mode : mode=<aaa>,
status=<bbb...b>
[Classification] INFO
[Explanation] It indicates that ON/OFF of data rewrite at failure recovery was set.
aaa : on, off
bbb...b : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
iSM14425: Set write cache mode(maintenance) :
<aaa>mode=<bbb>, status=<ccc...c>
[Classification] INFO
[Explanation] It indicates that ON/OFF of write cache mode was set.
aaa : BBU or CNT
bbb : on, off
ccc...c : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
493
iSM14426: RANK rebuild time : RANK=<aa>h,
PDG=<bb>h, Time=<cc>,
status=<ddd...d>
[Classification] INFO
[Explanation] It indicates that RANK rebuild time was changed.
aa : RANK number
bb : PD group number
cc : Rebuild time
ddd...d : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
iSM14427: LD format time: Time=<aa>,
status=<bbb...b>
[Classification] INFO
[Explanation] It indicates that format time of Logical Disk was changed.
aa : Format time
bbb...b : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
494
iSM14428: Auto assignment mode:
mode=<aaa>, status=<bbb...b>
[Classification] INFO
[Explanation] It indicates that auto assignment mode was set.
aaa : on, off
bbb...b : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
iSM14429: Expand LUN mode: HD=<aa>h,
Port=<bb>h, mode=<cc>,
status=<ddd...d>
[Classification] INFO
[Explanation] It indicates that Expand LUN mode was set.
aa : on, off
bb : Host Director number
cc : Port number
ddd...d : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
495
iSM14430: Set LD reserve ( ): LDN=<aaaa>h,
<aaaa>h..., status=<bbb...b>
[Classification] INFO
[Explanation] It indicates that the logical disk was set to the reserve group.
aaaa : Logical disk number
bbb...b : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
iSM14431: Cancel LD reserve ( ): LDN=<aaaa>h,
<aaaa>h..., status=<bbb...b>
[Classification] INFO
[Explanation] It indicates that the logical disk was released from the reserve group.
aaaa : Logical disk number
bbb...b : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
496
iSM14432: Start data initialize : LDN=<aaaa>h,
<aaaa>h..., status=<bbb...b>
[Classification] INFO
[Explanation] It indicates that initialization of the logical disk began.
aaaa : Logical disk number
bbb...b : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
iSM14433: Stop data initialize : LDN=<aaaa>h,
<aaaa>h..., status=<bbb...b>
[Classification] INFO
[Explanation] It indicates that initialization of the logical disk was suspended.
aaaa : Logical disk number
bbb...b : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
497
iSM14434: Change data initialize time :
Time=<aa>, status=<bbb...b>
[Classification] INFO
[Explanation] It indicates that logical disk initialization time was changed.
aa : Initialization time
bbb...b : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
iSM14435: Set LD reserve (optimization) :
LDN=<aaaa>h, <aaaa>h...,
status=<bbb...b>
[Classification] INFO
[Explanation] It indicates that the logical disk was set to the work disk for optimization.
aaaa : Logical disk number
bbb...b : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
498
iSM14436: Cancel LD reserve (optimization) :
LDN=<aaaa>h, <aaaa>h...,
status=<bbb...b>
[Classification] INFO
[Explanation] It indicates that the logical disk was released from the work disk for
optimization.
aaaa : Logical disk number
bbb...b : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
iSM14437: Set default LD name : LDN=<aaaa>h,
status=<bbb...b>
[Classification] INFO
[Explanation] It indicates that the logical disk name was initialized to the default.
aaaa : Logical disk number
bbb...b : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
499
iSM14438: Set Port Platform : Platform=<aa>,
HD=<bb>h, Port=<cc>h,
status=<ddd...d>
[Classification] INFO
[Explanation] The OS type of the port has been set.
aa : Set platform
bb : Host director number
cc : Port number
ddd...d : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
iSM14439: Shutdown Disk Array :
status=<aaa...a>
[Classification] INFO
[Explanation] Shutdown process of disk array started.
aaa...a : Command execution status
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or settings of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again. If accesses
from business server exist, terminate the accesses.
Chapter 2 Message List
500
iSM14440: <aaa> Control Software update :
status=failed
[Classification] INFO
[Explanation] Indicates failure in updating storage control software.
aaa : Subjected resource
HD : Host director
DD : Disk director
SVP : Service processor
[Measures] The configuration or setting of the disk array may be changed. After updating it
to the newest information or restarting state monitoring, check current state and
execute again.
iSM14441: Storage Control Software update :
status=<aaa...a>
[Classification] INFO
[Explanation] It indicates that storage control software has been updated. Upon normal
operation, iSM14439 and iSM14442 messages are output also.
aaa...a : Command execution status
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
501
iSM14442: Reset resource : resource=<aaa>,
number=<bb>h, status=<ccc...c>
[Classification] INFO
[Explanation] It indicates that resetting of resource or disk array started.
aaa : Subjected resource
SVP : Service processor
all : Whole disk array
bb : Resource number applicable to resetting (all for the whole disk
array)
ccc...c : Command execution status
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. Check that accesses to disk array have
terminated. Turn off and then on the power, and then check current state.
Chapter 2 Message List
502
iSM14443: Set IP Address : number=<aa>h,
(IP Address=<bbb...b>, Subnet
Mask=<ccc...c>, Gateway
Address=<ddd...d>) ->
(IP Address=<eee...e>, Subnet
Mask=<fff...f>, Gateway
Address=<ggg...g>), status=<hhh...h>
[Classification] INFO
[Explanation] It indicates that IP address, subnet mask, and gateway address have been
specified for the disk array. Information specified here becomes valid after
resetting disk array or service processor.
aa : Service processor number
bbb...b : IP address before change
ccc...c : Subnet mask before change
ddd...d : Gateway address before change
eee...e : IP address after change
fff...f : Subnet mask after change
ggg...g : Gateway address after change
hhh...h : Command execution status
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again. If state
monitoring cannot be restarted, specified IP address, etc., may be wrong. If a
wrong IP address, etc. have been specified, specify a correct address with
iSMnetconf command.
Chapter 2 Message List
503
iSM14444: Set SCSI Socket permission :
number=<aa>h, SCSI Socket Guard
Invalid=<bbb>, SCSI Socket Valid IP
Address=<ccc...c>,<ccc...c>...,
status=<ddd...d>
[Classification] INFO
[Explanation] Indicates access restriction has been specified on monitoring server.
Information specified here becomes valid after resetting disk array or service
processor.
aa : Service processor number
bbb : Access restriction status on monitoring server (on or off)
ccc...c : IP address to allow access (only when access restriction is on)
ddd...d : Command execution status
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
---- : Interrupted
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again. If state
monitoring cannot be restarted, specified IP address, etc., may be wrong. If a
wrong IP address, etc. have been specified, disable access restriction with
iSMnetconf command, and retry command execution.
Chapter 2 Message List
504
iSM14445: Set SNMP Request permission :
number=<aa>h, SNMP Valid=<bb>,
Community Name=“<ccc...c>”,
SNMP Valid IP Address=<ddd...d>,
<ddd...d>..., status=<eee...e>
[Classification] INFO
[Explanation] Indicates access restriction has been specified by SNMP request. Information
specified here becomes valid after resetting disk array or service processor.
aa : Service processor number
bb : Access restriction status by SNMP request (on or off)
ccc...c : Community name
ddd...d : IP address to allow access (only when access restriction is on)
eee...e : Command execution status
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
---- : Interrupted
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
505
iSM14446: LD Bind(maintenance) :
LDN=<aaaa>h, <aaaa>h...,
RANK=<bb>h, PDG=<cc>h,
status=<ddd...d>
[Classification] INFO
[Explanation] It indicates that logical disks have been configured. After normal operation,
iSM14410 message is output also.
aaaa : Logical disk number
bb : RANK number
cc : PD group number
ddd...d : Command execution status
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
iSM14447: License <aaa…a> :
Product=<bbb...b>, status=<ccc...c>
[Classification] INFO
[Explanation] It indicates that license was released or locked.
aaa…a : Setting type
Release : License released
Lock : License locked
bbb...b : Program product name
ccc...c : Command execution status
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
506
iSM14448: Set SNMP Trap Transmission :
number=<aa>h, Community
Name=“<bbb...b>”, SNMP Trap IP
Address=<ccc...c>,<ccc...c>,...,
status=<ddd...d>
[Classification] INFO
[Explanation] It indicates that sending destination of SNMP trap was specified. Information
specified here becomes valid after resetting disk array or service processor.
aa : Service processor number
bbb...b : Community name
ccc...c : IP address of SNMP Trap sending destination
ddd...d : Command execution status
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
---- : Interrupted
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
507
iSM14449: Set SNMP Trap Information :
number=<aa>h, Trap Sense
Interval=<bb>, Unit
Contact=“<ccc...c>”, Unit
Name=“<ddd...d>”, Unit
Location=“<eee...e>”, Unit
Info=“<fff...f>”, status=<ggg...g>
[Classification] INFO
[Explanation] It indicates that SNMP trap information was specified. Information specified
here becomes valid after resetting disk array or service processor.
aa : Service processor number
bb : Trap monitoring interval (unit: second)
ccc...c : Management information (administrator of disk array, managing
department, and contact address)
ddd...d : System name (nickname of disk array, using host name, etc.)
eee...e : Installation site (installation sited of disk array)
fff...f : Supplementary information (other information required for
managing)
ggg...g : Command execution status
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
---- : Interrupted
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
508
iSM14450: Set CachePartitioning mode:
mode=<aaa> initialize=<bbbb>,
status=<ccc...c>
[Classification] INFO
[Explanation] It indicates that the cache partitioning function has started/stopped.
aaa : Cache partitioning function starting/termination (on or off)
bbbb : Initial status of settings at cache partitioning function starting (on,
off, or “----”)
ccc...c : Command execution status
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
509
iSM14451: Define cache segment : segment
number=<aa>h, segment
name=“<bbb...b>”, max.
capacity=<ccc...c>GB, min.
capacity=<ddd...d>GB,
status=<eee...e>
[Classification] INFO
[Explanation] It indicates that the cache segment has been created.
aa : Cache segment number
bbb...b : Cache segment name
ccc...c : Max. allocated cache capacity
ddd...d : Min. allocated cache capacity
eee...e : Command execution status
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
510
iSM14452: Delete cache segment : segment
number=<aa>h, segment
name=“<bbb...b>”, status=<ccc...c>
[Classification] INFO
[Explanation] It indicates that the cache segment has been deleted.
aa : Cache segment number
bbb...b : Cache segment name
ccc...c : Command execution status
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
511
iSM14453: Set cache segment information:
segment number=<aa>h, segment
name=“<bbb...b>”, max.
capacity=<ccc...c>GB, min.
capacity=<ddd...d>GB,
status=<eee...e>
[Classification] INFO
[Explanation] It indicates that the cache segment information has been changed.
aa : Cache segment number
bbb...b : Cache segment name
ccc...c : Max. allocated cache capacity
ddd...d : Min. allocated cache capacity
eee...e : Command execution status
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
512
iSM14454: Assign LD to cache segment :
segment number=<aa>h, segment
name=“<bbb...b>”, LDN=<ccc...c>,
<ccc...c>..., status=<ddd...d>
[Classification] INFO
[Explanation] It indicates that LD assigned to cache segment has been changed.
aa : Number of cache segment to which LD was added
bbb...b : Name of cache segment to which LD was added
ccc...c : LD number of which LD assignment has been changed
ddd...d : Command execution status
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the newest information or
restarting state monitoring, check current state and execute again.
Chapter 2 Message List
513
iSM14456: Pool bind : Pool number=<aaaa>h,
Type=<bbb...b>, PD count=<cccc>,
PDN=<dd>h-<ee>h, <dd>h-<ee>h, ...,
Time=<ff>, RAID=<ggg...g>,
status=<hhh...h>
[Classification] INFO
[Explanation] It indicates that pool bind has been executed.
aaaa : Pool number
bbb...b : Pool type
dynamic : Dynamic
basic : Basic
cccc : Number of physical disks
dd : PD group number
ee : Physical disk number
ff : Rebuild time
ggg...g : RAID type
1 : RAID 1
5 : RAID 5
10 : RAID 10
50 : RAID 50
6(4+PQ) : RAID 6
6(8+PQ) : RAID 6
hhh...h : Execution state of the command
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the latest information or
restarting state monitoring, check the current state and execute the command
again.
Chapter 2 Message List
514
iSM14457: Pool unbind : Pool number=<aaaa>h,
PD count=<bbbb>,
PDN=<cc>h-<dd>h, <cc>h-<dd>h, ...,
status=<eee...e>
[Classification] INFO
[Explanation] It indicates that pool unbind has been executed.
aaaa : Pool number
bbbb : Number of physical disks
cc : PD group number
dd : Physical disk number
eee...e : Execution state of the command
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the latest information or
restarting state monitoring, check the current state and execute the command
again.
Chapter 2 Message List
515
iSM14458: Pool expansion : Pool
number=<aaaa>h, PD count=<bbbb>,
PDN=<cc>h-<dd>h, <cc>h-<dd>h, ...,
restruct=<eee>, Time=<fff>,
status=<ggg...g>
[Classification] INFO
[Explanation] It indicates that pool expansion has been executed.
aaaa : Pool number
bbbb : Number of physical disks
cc : PD group number
dd : Physical disk number
eee : Rebuilding
on : With pool rebuilding
off : Without pool rebuilding
fff : Expansion time
ggg...g : Execution state of the command
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed or the state of the specified pool may not be
normal. Restart state monitoring and check the current state.
Chapter 2 Message List
516
iSM14459: Pool rebuild/expansion time : Pool
number=<aaaa>h, rebuild time=<bb>,
expansion time=<ccc>,
status=<ddd...d>
[Classification] INFO
[Explanation] It indicates that the pool expansion time has been changed.
aaaa : Pool number
bb : Rebuild time
ccc : Expansion time
ddd...d : Execution state of the command
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the latest information or
restarting state monitoring, check the current state and execute the command
again.
Chapter 2 Message List
517
iSM14461: LD bind : LDN=<aaaa>h, <aaaa>h...,
Pool number=<bbbb>h, LD
capacity=<ccc...c>GB, Time=<dd>,
status=<eee...e>
[Classification] INFO
[Explanation] It indicates that LD bind has been executed.
aaaa : Logical disk number
bbbb : Pool number
ccc...c : Logical disk capacity
dd : Binding time
eee...e : Execution state of the command
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the latest information or
restarting state monitoring, check the current state and execute the command
again.
Chapter 2 Message List
518
iSM14462: LD expansion : LDN=<aaaa>h, LD
capacity=<bbb...b>GB, Time=<cc>,
status=<ddd...d>
[Classification] INFO
[Explanation] It indicates that LD expansion has been executed.
aaaa : Logical disk number
bbb...b : Logical disk capacity (after expansion)
cc : Expansion time
ddd...d : Execution state of the command
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed or the state of the specified logical disk may not
be normal. Restart state monitoring and check the current state.
iSM14464: Pool name : Pool number=<aaaa>h,
new name= “<bbb...b>” (old
name=“<ccc...c>”), status=<ddd...d>
[Classification] INFO
[Explanation] It indicates that the pool name has been changed.
aaaa : Pool number
bbb...b : New pool name
ccc...c : Old pool name
ddd...d : Execution state of the command
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration or setting of
the disk array may be changed. After updating it to the latest information or
restarting state monitoring, check the current state and execute the command
again.
Chapter 2 Message List
519
iSM14467: SRA expansion : LD(SDV)
number=<aaaa>h,<aaaa>h..., Pool
number=<bbbb>h, SRA
capacity=<ccc...c>GB,
threshold=<ddd...d>GB(<ee>%),
status=<fff...f>
[Classification] INFO
[Explanation] It indicates that SRA was expanded.
aaaa : Logical disk (SDV) number
bbbb : Pool number
ccc...c : SRA capacity (GB)
ddd...d : Threshold (GB)
ee : Threshold (%)
fff...f : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), restart state monitoring and
check the following items.
- Pool status
Chapter 2 Message List
520
iSM14468: SRA bind : LD(SDV)
number=<aaaa>h,<aaaa>h..., Pool
number=<bbbb>h, SRA
capacity=<ccc...c>GB,
threshold=<ddd...d>GB(<ee>%),
status=<fff...f>
[Classification] INFO
[Explanation] It indicates that SRA was bound.
aaaa : Logical disk (SDV) number
bbbb : Pool number
ccc...c : SRA capacity (GB)
ddd...d : Threshold (GB)
ee : Threshold (%)
fff...f : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), restart state monitoring and
check the following items.
- Pool status
Chapter 2 Message List
521
iSM14469: LV bind : LD(LV)
number=<aaaa>h,<aaaa>h...(LD(BV)
number=<bbbb>h,<bbbb>h...), Pool
number=<cccc>h, status=<ddd...d>
[Classification] INFO
[Explanation] It indicates that LV was bound.
aaaa : Logical disk (LV) number
bbbb : Logical disk (BV) number permitted to be linked
cccc : Pool number
ddd...d : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the status impossible in normal
operation may have occurred. Update to the latest information or restart state
monitoring and start snapshot management. Then, check the following items.
- Pool state
- SV state
- LV state and link permission volume list
Chapter 2 Message List
522
iSM14470: SV bind : LD(SV)
number=<aaaa>h,<aaaa>h...(LD(BV)
number=<bbbb>h), Pool
number=<cccc>h, SV count=<dd>,
status=<eee...e>
[Classification] INFO
[Explanation] It indicates that a generation was added (SV was bound).
aaaa : Logical disk (SV) number
bbbb : Number of logical disk (BV) to which the generation is added
cccc : Pool number
dd : Number of generations to be added
eee...e : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the status impossible in normal
operation may have occurred. Update to the latest information or restart state
monitoring and start snapshot management. Then, check the following items.
- Pool state
- SV state
- LV state and link permission volume list
Chapter 2 Message List
523
iSM14471: SRA unbind : Pool number=<aaaa>h,
LD(SDV)
number=<bbbb>h,<bbbb>h...,
status=<ccc...c>
[Classification] INFO
[Explanation] It indicates that SRA was unbound.
aaaa : Pool number
bbbb : Logical disk (SDV) number
ccc...c : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), restart state monitoring and
check the following items.
- Pool state
Chapter 2 Message List
524
iSM14472: SV unbind : LD(SV)
number=<aaaa>h,<aaaa>h...(LD(BV)
number=<bbbb>h), SV count=<cc>,
status=<ddd...d>
[Classification] INFO
[Explanation] It indicates that a generation was removed (SV was unbound).
aaaa : Logical disk (SV) number
bbbb : Number of logical disk (BV) from which the generation is
removed
cc : Number of generations to be removed
ddd...d : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the status impossible in normal
operation may have occurred. Update to the latest information or restart state
monitoring and start snapshot management. Then, check the following items.
- Pool state
- SV state
- LV state and link permission volume list
Chapter 2 Message List
525
iSM14474: SRA threshold : Pool
number=<aaaa>h,
threshold=<bbb...b>GB (<cc>%),
status=<ddd...d>
[Classification] INFO
[Explanation] It indicates that threshold was changed.
aaaa : Pool number
bbb...b : Threshold (GB)
cc : Threshold (%)
ddd...d : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), restart state monitoring and
check the following items.
- Pool state
iSM14475: Configuration reserved(reference
mode). : Disk Array=<aaa...a>,
status=<bbb...b>
[Classification] INFO
[Explanation] It indicates that configuration setting is started in the reference mode.
aaa...a : Disk array name
bbb...b : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the configuration of specified
disk array may be being set by another configuration setting software. After
exiting all configuration setting software, re-execute.
Chapter 2 Message List
526
iSM14476: Configuration released(reference
mode).: Disk Array=<aaa...a>,
status=<bbb...b>
[Classification] INFO
[Explanation] It indicates that the reference mode of configuration setting is ended.
aaa...a : Disk array name
bbb...b : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs (status=failed was output), the disk array or control path
may be failed. After troubleshooting, disconnect and re-connect the iSM client of
which configuration has been set.
iSM14600: Internal error : detail=<aaa...a>,
code=<bbbb>
[Classification] INFO
[Explanation] It indicates that an internal error such as a communication error and system call
error occurred.
aaa...a : The following output will be provided depending on an error
content.
communication : Communication error
system call : System call error
process busy : Time out in waiting for termination
(Windows version only)
function api : Internal API error
seize : Disk array occupation error
bbbb : Internal code such as errno
[Measures] Check whether any abnormality has occurred in the processes making up the
iSM server or in the operation environment, then restart the iSM server.
Chapter 2 Message List
527
iSM14601: Forced termination : status=<aaa...a>
[Classification] INFO
[Explanation] It indicates that the “Configurating” state was forcefully canceled.
aaa...a : Execution state of the command.
good : Normal
failed(xxxx) : Error occurred (xxxx is error description)
[Measures] When an error occurs, check whether any abnormality has occurred in the
processes making up the iSM server or in the operation environment, then restart
the iSM server.
Chapter 2 Message List
528
iSM15000 ∼
iSM15600: Internal error : detail=<aaa...a>,
code=<bbbb>
[Classification] INFO
[Explanation] It indicates that such internal error as communication error and system call error
occurred.
aaa...a : The following output will be provided depending on an error
content.
communication : detail=communication
system call : detail=system call
process busy : Time out in waiting for termination
(Windows version only)
bbbb : Internal code such as errno
[Measures] Check whether any abnormality has occurred in the processes making up the
iSM server or in the operation environment, then restart the iSM server.
Chapter 2 Message List
529
iSM16000 ~
iSM16001: iSMalived process has started.
function=<aaa...a> AUTH=<bbb...b>
[Classification] INFO
[Explanation] It indicates that ALIVEmail process has started.
aaa...a : Function name that has started
SG Error : Process has started, but notification is not
executed because of SG setting error (function
blockage state).
Alert : Error report
Heartbeat : Heartbeat report
Regulary : Periodical error report
RunningMainte : Scheduled maintenance report
bbb...b : Authentication method for accessing a mail server
NONE : Conventional authentication method
without SMTP authentication
SMTP_AUTH : SMTP Auth authentication method
POP_BEFORE_SMTP : POP before SMTP authentication
method
[Measures] Unnecessary (normal operation). Check the setting file if the operating function
is different from the setting.
iSM16020: Function Error has occurred.
name=<aaa...a> code=<bbbb>
errno=<ccc>
[Classification] NOTICE
[Explanation] It shows that a function error has occurred.
aaa...a : Function name
bbbb : Internal code
ccc : Error number
[Measures] Check the settings relevant to the applicable function.
Chapter 2 Message List
530
iSM16021: Internal Error has occurred.
code=<aaaa> errno=<bbb>
[Classification] NOTICE
[Explanation] It shows that an internal error has occurred.
aaaa : Internal code
bbb : Error number
[Measures] Check the server operating environment and various settings.
iSM16029: File does not exist. file=<aaa...a>
[Classification] WARNING
[Explanation] It shows that ALIVEmail setting file or message information table file does not
exist.
aaa...a : File name
alived.conf : Setting file
alived.tbl : Message information table file
[Measures] Check the folder for the ALIVEmail setting file or message information table file,
and create a file properly.
Chapter 2 Message List
531
iSM16030: File cannot be opened. errno=<aaa>
file= <bbb...b>
[Classification] WARNING
[Explanation] It shows that opening of the ALIVEmail setting file or message information table
file has failed.
aaa : Error number
bbb...b : File name
alived.conf : Setting file
alived.tbl : Message information table file
alived.hst : Record file
[Measures] Check the conditions of the ALIVEmail setting file or message information table
file.
iSM16031: File cannot be read. file=alived.conf
line=<aa> errno=<bbb>
[Classification] WARNING
[Explanation] It indicates that reading the ALIVEmail setting file has failed.
aa : Error line number
bbb : Error number
[Measures] Check the conditions of the ALIVEmail setting file (such as reading privilege).
iSM16032: Illegal configuration. file=alived.conf
First line is not [ALIVE].
[Classification] WARNING
[Explanation] It indicates that the first line of the ALIVEmail setting file is not [ALIVE].
[Measures] The header should be [ALIVE]. Check the contents of the file.
Chapter 2 Message List
532
iSM16033: Illegal configuration. file=alived.conf
Tag overlaps. line=<aa>
tag=<bbb...b>
[Classification] WARNING
[Explanation] It indicates that the tags overlap in the ALIVEmail setting file.
aa : Error line number
bbb...b : Tag name
[Measures] Check the syntax of the ALIVEmail setting file and correct it.
iSM16034: Illegal configuration. file=alived.conf
First word is not keyword. line=<aa>
[Classification] WARNING
[Explanation] It indicates that it is the applicable line of ALIVEmail setting file and the first
word is not a keyword.
aa : Error line number
[Measures] Check the syntax of the ALIVEmail setting file and correct it.
Chapter 2 Message List
533
iSM16035: Illegal configuration. file=alived.conf
id=<a> line=<bb>
[Classification] WARNING
[Explanation] It indicates that there is Invalid description in the ALIVEmail setting file.
a : Error classification
1: Improper position of “=”, or no “=”
2: Improper position of “:”, or no “:”
3: Improper position of “,”, or too many “,”
6: Improper position of ““”, or no ““”
8: No description of address
9: Inconsistency existing among set values
bb : Error line number
[Measures] Check the relevant line of the ALIVEmail setting file, and correct the definition.
iSM16037: Illegal configuration. file=alived.conf
Specific tag is not defined.
tag=<aaa...a>
[Classification] WARNING
[Explanation] It indicates that there is no definition of the specific tag in the ALIVEmail setting
file.
aaa...a : Tag name
[Measures] Check the syntax of the ALIVEmail setting file, and correct the definition of the
specific tag.
Chapter 2 Message List
534
iSM16038: Illegal configuration. file=alived.conf
It has exceeded 256 bytes. line=<aa>
[Classification] WARNING
[Explanation] It indicates that the applicable line of the ALIVEmail setting file exceeds 256
bytes.
aa : Error line number
[Measures] Check the applicable line of the ALIVEmail setting file, and correct it 256 bytes
or less.
iSM16039: Illegal configuration. file=alived.conf
“TO” mail address has exceeded 10.
line=<aa>
[Classification] WARNING
[Explanation] It indicates that the destination mail addresses have been set over 10 in the
ALIVEmail setting file.
aa : Error line number
[Measures] Check the mail addresses to which the ALIVEmail setting file, and set the
number of address less.
iSM16041: File cannot be read. file=alived.tbl
line=<aa> errno=<bbb>
[Classification] WARNING
[Explanation] It indicates that reading the ALIVEmail message information table file has
failed.
aa : Error line number
bbb : Error number
[Measures] Check the state of the ALIVEmail message information table file (such as
reading privilege).
Chapter 2 Message List
535
iSM16043: Illegal configuration. file=alived.tbl
Tag overlaps. line=<aa>
tag=<bbb...b>
[Classification] WARNING
[Explanation] It indicates that the tags overlap in the ALIVEmail message information table
file.
aa : Error line number
bbb...b : Tag name
[Measures] Check the syntax of the ALIVEmail message information table file and correct it.
iSM16044: Illegal configuration. file=alived.tbl
First word not keyword. line=<aa>
[Classification] WARNING
[Explanation] It indicates that it is the applicable line of the ALIVEmail message information
table file and the first word is not a keyword.
aa : Error line number
[Measures] Check the syntax of the ALIVEmail message information table file and correct it.
Chapter 2 Message List
536
iSM16045: Illegal configuration. file=alived.tbl
id=<a> line=<bb>
[Classification] WARNING
[Explanation] It indicates that there is Invalid description in the ALIVEmail message
information table file.
a : Error classification
1: Improper position of “=”, or no “=”
5: Improper position of “,”
8: No description of address
bb : Error line number
[Measures] Check the relevant line of the ALIVEmail message information table file, and
correct the definition.
iSM16047: Illegal configuration. file=alived.tbl
Specific tag is not defined.
tag=<aaa...a>
[Classification] WARNING
[Explanation] It indicates that there is no definition of the specific tag in the ALIVEmail
message information table file.
aaa...a : Tag name
[Measures] Check the syntax of the ALIVEmail message information table file, and correct
the definition of the specific tag.
Chapter 2 Message List
537
iSM16048: Illegal configuration. file=alived.tbl
It has exceeded 256 bytes. line=<aa>
[Classification] WARNING
[Explanation] It indicates that the applicable line of the ALIVEmail message information table
file exceeds 256 bytes.
aa : Error line number
[Measures] Check the applicable line of the ALIVEmail message information table file, and
correct it in 256 bytes or less.
iSM16049: Illegal configuration. file=alived.tbl
Message number has exceeded 1000.
line=<aa>
[Classification] WARNING
[Explanation] It indicates that the set number of messages in the ALIVEmail message
information table file exceeds 1000.
aa : Error line number
[Measures] Check the ALIVEmail message information table file, and set the messages to
1000 or less.
iSM16061: Mail server (<aaa...a>) address is
illegal.
[Classification] WARNING
[Explanation] It indicates that the address specified to the mail server is illegal.
aaa...a : Mail server type
SMTP : Address of SMTP server
POP : Address of POP server
[Measures] Specify the mail server with the DNS name or IP address.
Chapter 2 Message List
538
iSM16062: Mail server cannot be connected.
name=<aaa...a> code=<bbbb>
errno=<ccc>
[Classification] WARNING
[Explanation] It indicates that the connection to mail server has failed.
aaa...a : Function name
bbbb : Internal code
ccc : Error number
[Measures] Failed in connection with mail server specified in the ALIVEmail setting file.
Check the address and operations of the specified mail server.
iSM16063: Communication error(receive from
mail server). name=<aaa...a>
code=<bbbb> errno=<ccc>
[Classification] WARNING
[Explanation] It indicates that receiving from the mail server has failed.
aaa...a : Function name
bbbb : Internal code
ccc : Error number
[Measures] Check the operations of the specified mail server, and resolve the problem.
Chapter 2 Message List
539
iSM16064: Communication error(send to mail
server). name=<aaa...a>
code=<bbbb> errno=<ccc>
[Classification] WARNING
[Explanation] It indicates that transmitting to mail server has failed.
aaa...a : Function name
bbbb : Internal code
ccc : Error number
[Measures] Check the operations of the specified mail server, and resolve the problem.
iSM16065: Communication error(mail server).
id=<a> send=<bbb...b> recv=<ccc...c>
[Classification] WARNING
[Explanation] It indicates that the communication error occurred with the mail server.
a : Internal code number
bbb...b : Sending information
ccc...c : Reception information
[Measures] Check the operations of the specified mail server, and resolve the problem based
on the information.
iSM16066: Mail server was time out.
[Classification] WARNING
[Explanation] It indicates that the operation of the mail server is slow and going to timeout.
[Measures] Check the operations of the specified mail server, and consider the restriction of
mail volume, the operation of mail server and path’s communication speed.
Chapter 2 Message List
540
iSM16070: Message buffer is full. Data losing is
detected.
[Classification] WARNING
[Explanation] It indicates that messages have been deleted because the message buffer capacity
exceeded the limit.
[Measures] There are too many messages for link. Definition must be reviewed.
iSM16071: Data losing is recovered.
[Classification] WARNING
[Explanation] It indicates that the message lost by the overflow of message buffer has been
recovered.
This message is output on UNIX system.
(Output only to syslog)
[Measures] This message is output in pair with iSM16070, which indicates that too many
messages to be linked exist, and indicates recovery of the error. Review the
definition.
Chapter 2 Message List
541
iSM16080: Definition change is successful.
function=<aaa...a> AUTH=<bbb...b>
[Classification] INFO
[Explanation] It indicates that the setting information change was successful.
aaa...a : Function name that has started
Alert : Error report
Heartbeat : Heartbeat report
Regulary : Periodical error report
RunningMainte : Scheduled maintenance report
bbb...b : Authentication method for accessing a mail server
NONE : Conventional authentication method
without SMTP authentication
SMTP_AUTH : SMTP Auth authentication method
POP_BEFORE_SMTP : POP before SMTP authentication
method
[Measures] Unnecessary (normal operation). Check the setting file if the operating function
is different from the setting.
iSM16081: Definition change error. ALIVEmail
function does not start.
[Classification] WARNING
[Explanation] It indicates that it failed to change the setting information. The driven function
does not operate till it succeeds.
[Measures] While trying to change the setting information with the iSM server running, the
definition error occurred. Correct the setting information error and execute the
change command again.
Chapter 2 Message List
542
iSM16082: Definition change error. ALIVEmail
function continues to operate by old
one.
[Classification] WARNING
[Explanation] The setting file change was failed. The driven function operates by the old
function before changing.
[Measures] While trying to change the setting information with the iSM server running, the
definition error occurred. Correct the setting information error and execute the
change command again.
iSM16083: Making of file directory error.
code=<aaaa> path=<bbb...b>
errno=<ccc>
[Classification] ERROR
[Explanation] It indicates that it failed to create directory.
aaaa : Code number
bbb...b : Directory name
ccc : Error number
[Measures] There is an error in the authority of installation directory and so on.
iSM16084: Change directory error.
name=<aaa...a> path=<bbb...b>
errno=<ccc>
[Classification] ERROR
[Explanation] It indicates that the directory change has been failed.
aaa...a : Function name
bbb…b : Directory name
ccc : Error number
[Measures] There is an error in the authority of installation directory and so on.
Chapter 2 Message List
543
iSM17000 ∼
iSM17001: Ftp environment(user) is not defined.
File Transfer function can not be
used. detail=<aa-bbbb>
[Classification] NOTICE
[Explanation] File transfer function cannot be used because FTP user name has not been
defined.
aa-bbbb : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify correct description of file_transfer section (user) in environment
definition file, and restart the iSM server. In particular, on Windows system,
specify a correct FTP user name in environment setting (Detail 2 file transfer
information), and restart the iSM server.
iSM17002: Ftp environment(ftp_root_directory)
is invalid. File Transfer function can
not be used. detail=<aa-bbbb>
[Classification] NOTICE
[Explanation] File transfer function cannot be used because root directory of FTP server has not
been defined correctly.
aa-bbbb : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify correct description of file_transfer section (ftp_root_directory) in
environment definition file, and restart the iSM server. In particular, on
Windows system, specify a correct root folder of FTP site in environment setting
(Detail 2 file transfer information), and restart the iSM server.
Chapter 2 Message List
544
iSM17003: Ftp environment(temp_directory) is
invalid. File Transfer function can not
be used. detail=<aa-bbbb>
[Classification] NOTICE
[Explanation] File transfer function cannot be used because work file storing directory has not
been defined correctly.
aa-bbbb : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify correct description of file_transfer section (temp_directory) in
environment definition file, and restart the iSM server. In particular, on
Windows system, specify a correct work file storing folder in environment
setting (Detail 2 file transfer information), and restart the iSM server.
iSM17004: Temp directory is not under ftp root
directory. File Transfer function can
not be used. detail=<aa-bbbb>
[Classification] NOTICE
[Explanation] File transfer function cannot be used because work file storing directory is not in
the root directory of FTP server.
aa-bbbb : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Specify that work file storing directory is in the root directory of FTP server by
file_transfer section in environment definition file, and restart the iSM server.
In particular, on Windows system, specify a correct work file storing folder to be
in the root folder of FTP site by environment setting (Detail 2 file transfer
information) or specify a correct virtual directory path and restart the iSM server.
Chapter 2 Message List
545
iSM17010: File access has failed. func=<aaa...a>
path=<bbb...b> errno=<ccc>
detail=<dd-eeee>
[Classification] NOTICE
[Explanation] An error occurred in file access function.
aaa...a : Function name
bbb...b : Path name
ccc : Error number
dd-eeee : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check function name and error number, take appropriate measures, and restart
the iSM server.
iSM17020: Socket access has failed.
func=<aaa...a> errno=<bbb>
detail=<cc-dddd>
[Classification] WARNING
[Explanation] An error occurred in socket access function.
aaa...a : Function name
bbb : Error number
cc-dddd : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check function name and error number, take appropriate measures, and restart
the iSM server.
Chapter 2 Message List
546
iSM17030: Memory access has failed.
func=<aaa...a> errno=<bbb>
detail=<cc-dddd>
[Classification] WARNING
[Explanation] An error occurred in memory access function. iSM server terminates
abnormally.
aaa...a : Function name
bbb : Error number
cc-dddd : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check function name and error number, take appropriate measures, and restart
the iSM server.
iSM17040: System call error has occurred.
func=<aaa...a> errno=<bbb>
detail=<cc-dddd>
[Classification] WARNING
[Explanation] An error occurred in system function. iSM server terminates abnormally.
aaa...a : Function name
bbb : Error number
cc-dddd : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Check function name and error number, take appropriate measures, and restart
the iSM server.
Chapter 2 Message List
547
iSM17050: Internal error has occurred.
detail=<aa-bbbb>
[Classification] WARNING
[Explanation] An internal error occurred in file transfer function. iSM server terminates
abnormally.
aa-bbbb : Detailed information (This code is not disorder reason but a
value for maintenance.)
[Measures] Save the following information and restart the iSM server.
y iSM operation log
y syslog (for other than Windows system)
y Event log (for Windows system)
iSM17900: Process is busy when it terminates
emergency. Unexpected error
message maybe generated.
[Classification] WARNING
[Explanation] It indicates that file transfer function decided to execute emergency termination,
but cannot terminate immediately.
[Measures] Unnecessary
Chapter 2 Message List
548
iSM18000 ∼
iSM18001: Snapshot has been created. (<aaa...a>,
BV=<bbb...b> (<cccc>h),
SV=<ddd...d> (<eeee>h))
[Classification] INFO
[Explanation] It indicates that snapshot was created.
aaa...a : Disk array name
bbb...b : BV logical disk name
cccc : BV logical disk number
ddd...d : SV logical disk name
eeee : SV logical disk number
[Measures] Unnecessary
iSM18002: Deleting snapshot has been started.
(<aaa...a>, BV=<bbb...b> (<cccc>h),
SV=<ddd...d> (<eeee>h),
generation=<fff>)
[Classification] INFO
[Explanation] It indicates that snapshot deletion was started.
aaa...a : Disk array name
bbb...b : BV logical disk name
cccc : BV logical disk number
ddd...d : SV logical disk name
eeee : SV logical disk number
fff : SV generation number when deletion was started
[Measures] Unnecessary
Chapter 2 Message List
549
iSM18003: Snapshot has been deleted. (<aaa...a>,
BV=<bbb...b> (<cccc>h),
SV=<ddd...d> (<eeee>h))
[Classification] INFO
[Explanation] It indicates that snapshot deletion was completed.
aaa...a : Disk array name
bbb...b : BV logical disk name
cccc : BV logical disk number
ddd...d : SV logical disk name
eeee : SV logical disk number
[Measures] Unnecessary
iSM18004: Restoring snapshot has been started.
(<aaa...a>, BV=<bbb...b> (<cccc>h),
SV=<ddd...d> (<eeee>h),
generation=<fff>)
[Classification] INFO
[Explanation] It indicates that snapshot restoring was started.
aaa...a : Disk array name
bbb...b : BV logical disk name
cccc : BV logical disk number
ddd...d : SV logical disk name
eeee : SV logical disk number
fff : SV generation number when restoring was started
[Measures] Unnecessary
Chapter 2 Message List
550
iSM18005: Snapshot has been restored.
(<aaa...a>, BV=<bbb...b> (<cccc>h),
SV=<ddd...d> (<eeee>h))
[Classification] INFO
[Explanation] It indicates that snapshot restoring was completed.
aaa...a : Disk array name
bbb...b : BV logical disk name
cccc : BV logical disk number
ddd...d : SV logical disk name
eeee : SV logical disk number
[Measures] Unnecessary
iSM18006: SV guard was changed. (<aaa...a>,
SV=<bbb...b> (<cccc>h), mode=<dd>)
[Classification] INFO
[Explanation] It indicates that the protection mode of snapshot-volume was changed.
aaa...a : Disk array name
bbb...b : SV logical disk name
cccc : SV logical disk number
dd : Protection mode setting state (on, off)
[Measures] Unnecessary
Chapter 2 Message List
551
iSM18007: Snapshot was cancelled. (<aaa...a>,
BV=<bbb...b> (<cccc>h),
SV=<ddd...d> (<eeee>h),
generation=<fff>)
[Classification] ERROR
[Explanation] It indicates that snapshot was cancelled due to insufficient capacity of snapshot
reserve area or other cause. Snapshot data is no longer accessible once snapshot
is cancelled.
For Windows, this message is target of ESMPRO Manager Report.
aaa...a : Disk array name
bbb...b : BV logical disk name
cccc : BV logical disk number
ddd...d : SV logical disk name
eeee : SV logical disk number
fff : SV generation number
[Measures] Check the status of snapshot reserve area. If the free space is not sufficient,
expand the snapshot reserve area or delete unnecessary snapshots. For details on
procedures, refer to “Snapshot User’s Manual (Function Guide)”.
Chapter 2 Message List
552
iSM18008: Snapshot was nullified. (<aaa...a>,
BV=<bbb...b> (<cccc>h),
SV=<ddd...d> (<eeee>h),
generation=<fff>)
[Classification] NOTICE
[Explanation] It indicates that snapshot was nullified because an old snapshot is restored.
Snapshot data is no longer accessible once snapshot is nullified.
aaa...a : Disk array name
bbb...b : BV logical disk name
cccc : BV logical disk number
ddd...d : SV logical disk name
eeee : SV logical disk number
fff : SV generation number
[Measures] Create snapshot if necessary.
iSM18201: Failed to create snapshot. (<aaa...a>,
BV=<bbb...b> (<cccc>h),
SV=<ddd...d> (<eeee>h),
code=<fff...f>)
[Classification] WARNING
[Explanation] It indicates that snapshot creation failed.
aaa...a : Disk array name
bbb...b : BV logical disk name
cccc : BV logical disk number
ddd...d : SV logical disk name
eeee : SV logical disk number
fff...f : Error code indicating the type of abnormal state
[Measures] Check the status of disk array referring to other related messages and remove the
error cause, for example, by repairing the fault. Then, re-execute.
Chapter 2 Message List
553
iSM18202: Failed to delete snapshot. (<aaa...a>,
BV=<bbb...b> (<cccc>h),
SV=<ddd...d> (<eeee>h),
generation=<fff>, code=<ggg...g>)
[Classification] WARNING
[Explanation] It indicates that snapshot deletion failed.
aaa...a : Disk array name
bbb...b : BV logical disk name
cccc : BV logical disk number
ddd...d : SV logical disk name
eeee : SV logical disk number
fff : SV generation number
ggg...g : Error code indicating the type of abnormal state
[Measures] Check the status of disk array referring to other related messages and remove the
error cause, for example, by repairing the fault. Then, re-execute.
iSM18203: Failed to restore snapshot. (<aaa...a>,
BV=<bbb...b> (<cccc>h),
SV=<ddd...d> (<eeee>h),
generation=<fff>, code=<ggg...g>)
[Classification] WARNING
[Explanation] It indicates that snapshot restoring failed.
aaa...a : Disk array name
bbb...b : BV logical disk name
cccc : BV logical disk number
ddd...d : SV logical disk name
eeee : SV logical disk number
fff : SV generation number
ggg...g : Error code indicating the type of abnormal state
[Measures] Check the status of disk array referring to other related messages and remove the
error cause, for example, by repairing the fault. Then, re-execute.
Chapter 2 Message List
554
iSM18204: Failed to change SV guard of
snapshot-volume. (<aaa...a>,
SV=<bbb...b> (<cccc>h),
code=<ddd...d>)
[Classification] WARNING
[Explanation] It indicates that the protection mode of snapshot-volume cannot be changed.
aaa...a : Disk array name
bbb...b : SV logical disk name
cccc : SV logical disk number
ddd...d : Error code indicating the type of abnormal state
[Measures] Check the status of disk array referring to other related messages and remove the
error cause, for example, by repairing the fault. Then, re-execute.
iSM18205: Monitoring stopped. (<aaa...a>)
[Classification] WARNING
[Explanation] It indicates that monitoring of snapshot function stopped due to faults.
aaa...a : Disk array name
[Measures] Check the status of disk array referring to other related messages and remove the
error cause, for example, by repairing the fault. Then, re-start disk array
monitoring.
Chapter 2 Message List
555
iSM18301: System call error has occurred.
(func=<aaa...a>, code=<bbb...b>,
errno=<cccc>)
[Classification] ERROR
[Explanation] It indicates that a system call error has occurred.
aaa...a : Abnormally terminated function name
bbb...b : Internal error code indicating the type of abnormal state
cccc : Error number
[Measures] Take necessary measures by checking the function name and error number and
restart the iSM server.
iSM18302: Internal error has occurred.
(code=<aaa...a>)
[Classification] ERROR
[Explanation] It indicates that the information within the server is inconsistent.
aaa...a : Error code indicating the type of abnormal state
[Measures] Collect necessary information according to the iSM error information collection
procedure, and restart the iSM server.
iSM18303: Parameter error has occurred.
(code=<aaa...a>)
[Classification] WARNING
[Explanation] It indicates that a parameter error was detected.
aaa...a : Error code indicating the type of abnormal state
[Measures] Collect necessary information according to the iSM error information collection
procedure, and restart the iSM server.
Chapter 2 Message List
556
iSM18311: Internal communication error has
occurred. (code=<aaa...a>)
[Classification] ERROR
[Explanation] In indicates that an internal communication error has occurred.
aaa...a : Internal error code indicating the type of abnormal state
[Measures] Collect necessary information according to the iSM error information collection
procedure, and restart the iSM server.
iSM18321: Access to diskarray was failed.
(<aaa...a>, code=<bbb...b>, <ccc...c>)
[Classification] WARNING
[Explanation] It indicates that access to disk array failed.
aaa...a : Disk array name
bbb...b : Detail code
ccc...c : Additional information
[Measures] Check the status of disk array referring to other related messages and remove the
error cause, for example, by repairing the fault. Then, re-execute. the operation if
necessary.
Chapter 2 Message List
557
iSM18501: Access mode was changed. (<aaa...a>,
LD=<bbb...b> (<cccc>h), mode from
<ddd...d> to <eee...e>)
[Classification] INFO
[Explanation] It indicates that the volume access mode was changed.
aaa...a : Disk array name
bbb...b : Logical disk name
cccc : Logical disk number
ddd...d : Access mode before change
eee...e : Access mode after change
[Measures] Unnecessary
iSM18502: Logical disk was linked to
link-volume.(<aaa...a>,LV=(<bbb...b>(
<cccc>h), LD=(<ddd...d>(<eeee>h))
[Classification] INFO
[Explanation] It indicates that the volume was linked to the link-volume.
aaa...a : Disk array name
bbb...b : Logical disk name of link-volume
cccc : Logical disk number of link-volume
ddd...d : Logical disk name of destination-volume
eeee : Logical disk number of destination-volume
[Measures] Unnecessary
Chapter 2 Message List
558
iSM18503: Logical disk was unlinked from
link-volume.(<aaa...a>,LV=<bbb...b>(<
cccc>h), LD=<ddd...d>(<eeee>h))
[Classification] INFO
[Explanation] It indicates that the volume was unlinked from the link-volume.
aaa...a : Disk array name
bbb...b : Logical disk name of link-volume
cccc : Logical disk number of link-volume
ddd...d : Logical disk name of destination-volume
eeee : Logical disk number of destination-volume
[Measures] Unnecessary
iSM18601: Failed to change access mode.
(<aaa...a>, LD=<bbb...b> (<cccc>h),
mode=<ddd...d>), code=<eee...e>)
[Classification] WARNING
[Explanation] It indicates that the volume access mode cannot be changed.
aaa...a : Disk array name
bbb...b : Logical disk name
cccc : Logical disk number
ddd...d : Access mode before change
eee...e : Error code indicating the type of abnormal state
[Measures] Check the status of disk array referring to other related messages and remove the
error cause, for example, by repairing the fault. Then, re-execute.
Chapter 2 Message List
559
iSM18602: Failed to link logical disk to
link-volume.(<aaa...a>,LV=<bbb...b>(<
cccc>h),
LD=<ddd...d>(<eeee>h),code=<fff...f>)
[Classification] WARNING
[Explanation] It indicates that the volume cannot be linked to the link-volume.
aaa...a : Disk array name
bbb...b : Logical disk name of link-volume
cccc : Logical disk number of link-volume
ddd...d : Logical disk name of destination-volume
eeee : Logical disk number of destination-volume
fff...f : Error code indicating the type of abnormal state
[Measures] Check the status of disk array referring to other related messages and remove the
error cause, for example, by repairing the fault. Then, re-execute.
iSM18603: Failed to unlink logical disk from
link-volume.(<aaa...a>,LV=<bbb...b>(<
cccc>h),
LD=<ddd...d>(<eeee>h),code=<fff...f>)
[Classification] WARNING
[Explanation] It indicates that the volume cannot be unlinked from the link-volume.
aaa...a : Disk array name
bbb...b : Logical disk name of link-volume
cccc : Logical disk number of link-volume
ddd...d : Logical disk name of destination-volume
eeee : Logical disk number of destination-volume
fff...f : Error code indicating the type of abnormal state
[Measures] Check the status of disk array referring to other related messages and remove the
error cause, for example, by repairing the fault. Then, re-execute.
Chapter 2 Message List
560
iSM18999: Unexpected error has occurred.
(code=<aaa...a>)
[Classification] WARNING
[Explanation] In indicates that an unexpected error has occurred.
aaa...a : Error code indicating the type of abnormal state
[Measures] Collect necessary information according to the iSM error information collection
procedure, and restart the iSM server.
Chapter 2 Message List
561
iSM19000 ∼
iSM19000: <aaa...a>
[Classification] INFO
[Explanation] Executed command line.
aaa...a : Entered character string
[Measures] Unnecessary
iSM19010: iSMsc_create has normally
terminated.
[Classification] INFO
[Explanation] iSMsc_create command normal termination message.
[Measures] Unnecessary
iSM19011: iSMsc_create has normally terminated.
[BV:<aaa...a>] [SV:<bbb...b>]
[Classification] INFO
[Explanation] iSMsc_create command normal termination message.
aaa...a : Volume name
bbb...b : Volume name
[Measures] Unnecessary
iSM19012: iSMsc_create has abnormally
terminated.
[Classification] INFO
[Explanation] iSMsc_create command abnormal termination message.
[Measures] Check the message displayed immediately before to handle it.
Chapter 2 Message List
562
iSM19013: iSMsc_create has abnormally
terminated. [BV:<aaa...a>]
[SV:<bbb...b>]
[Classification] INFO
[Explanation] iSMsc_create command abnormal termination message.
aaa...a : Volume name
bbb...b : Volume name
[Measures] Check the message displayed immediately before to handle it.
iSM19020: iSMsc_delete has normally
terminated.
[Classification] INFO
[Explanation] iSMsc_delete command normal termination message.
[Measures] Unnecessary
iSM19021: iSMsc_delete has normally terminated.
[BV:<aaa...a>] [SV:<bbb...b>]
[Classification] INFO
[Explanation] iSMsc_delete command normal termination message.
aaa...a : Volume name
bbb...b : Volume name
[Measures] Unnecessary
Chapter 2 Message List
563
iSM19022: iSMsc_delete has abnormally
terminated.
[Classification] INFO
[Explanation] iSMsc_delete command abnormal termination message.
[Measures] Check the message displayed immediately before to handle it.
iSM19023: iSMsc_delete has abnormally
terminated. [BV:<aaa...a>]
[SV:<bbb...b>]
[Classification] INFO
[Explanation] iSMsc_delete command abnormal termination message.
aaa...a : Volume name
bbb...b : Volume name
[Measures] Check the message displayed immediately before to handle it.
iSM19030: iSMsc_restore has normally
terminated.
[Classification] INFO
[Explanation] iSMsc_restore command normal termination message.
[Measures] Unnecessary
Chapter 2 Message List
564
iSM19031: iSMsc_restore has normally
terminated. [BV:<aaa...a>]
[SV:<bbb...b>]
[Classification] INFO
[Explanation] iSMsc_restore command normal termination message.
aaa...a : Volume name
bbb...b : Volume name
[Measures] Unnecessary
iSM19032: iSMsc_restore has abnormally
terminated.
[Classification] INFO
[Explanation] iSMsc_Restore command abnormal termination message.
[Measures] Check the message displayed immediately before to handle it.
iSM19033: iSMsc_restore has abnormally
terminated. [BV:<aaa...a>]
[SV:<bbb...b>]
[Classification] INFO
[Explanation] iSMsc_restore command abnormal termination message.
aaa...a : Volume name
bbb...b : Volume name
[Measures] Check the message displayed immediately before to handle it.
Chapter 2 Message List
565
iSM19034: iSMsc_restore has accepted the
request.
[Classification] INFO
[Explanation] It indicates that the iSMsc_restore command has accepted the request.
[Measures] Unnecessary
iSM19035: iSMsc_restore has accepted the
request. [BV:<aaa...a>] [SV:<bbb...b>]
[Classification] INFO
[Explanation] It indicates that the iSMsc_restore command has accepted the request.
aaa...a : Volume name
bbb...b : Volume name
[Measures] Unnecessary
iSM19100: The volume under restoration cannot
be specified. [BV:<aaa...a>]
[Classification] ERROR
[Explanation] It indicates that the request cannot be accepted because restore operation is
taking place in the specified volume.
aaa...a : Volume name
[Measures] Check the status with the query command and re-execute.
Chapter 2 Message List
566
iSM19101: The volume linked from LV cannot be
specified. [{BV|SV}:<aaa...a>]
[Classification] ERROR
[Explanation] It indicates that the request cannot be accepted because BV or SV is linked to
LV.
aaa...a : Volume name
[Measures] Remove the link (unlink) with the iSMcc_unlink command and re-execute.
iSM19102: The volume mounted cannot be
specified. [BV:<aaa...a>]
[Classification] ERROR
[Explanation] It indicates that the request cannot be accepted because the volume is mounted.
aaa...a : Volume name
[Measures] Unmount the volume and re-execute.
iSM19103: State of specified diskarray is 'freeze'.
[Classification] ERROR
[Explanation] The disk array where specified BV and SV are stored is in the freeze state.
[Measures] Cancel the freeze state and re-execute.
Chapter 2 Message List
567
iSM19104: The volume is not paired cannot be
specified. [BV:<aaa...a>]
[SV:<bbb...b>]
[Classification] ERROR
[Explanation] It indicates that the request cannot be accepted because the specified volume has
no pair setting.
aaa...a : Volume name
bbb...b : Volume name
[Measures] Check the volume and re-execute.
iSM19105: State of specified pair is invalid.
(state=<aaa...a>) [BV:<bbb...b>]
[SV:<ccc...c>]
[Classification] ERROR
[Explanation] Target pair status is invalid. The current status is indicated by aaa...a.
aaa...a : Target pair status
Not snap/active. : Snapshot is not established.
Not snap/active, snap/inactive. : Snapshot is (not) established.
bbb...b : Volume name
ccc...c : Volume name
[Measures] Check the volume and re-execute.
iSM19106: The volume of SV guard cannot be
specified. [SV:<aaa...a>]
[Classification] ERROR
[Explanation] Protection is specified for the target SV.
aaa...a : Volume name
[Measures] Deactivate the protection and re-execute.
Chapter 2 Message List
568
iSM19107: State of SV's access mode is invalid.
(mode=<aaa...a>) [SV:<bbb...b>]
[Classification] ERROR
[Explanation] The command cannot be executed because the SV access restriction is not "Not
Ready".
aaa...a : SV access restriction
rw : Input/output allowed
ro : Read only
na : Access prohibited
bbb...b : Volume name
[Measures] Check the access mode and re-execute.
iSM19108: The volume under deletion exists.
[BV:<aaa...a>]
[Classification] ERROR
[Explanation] It indicates that the request cannot be accepted because BV contains SV
currently being deleted.
aaa...a : Volume name
[Measures] Check that the relevant volume was completely deleted and re-execute.
iSM19109: The volume linked from LV exists.
[SV:<aaa...a>]
[Classification] ERROR
[Explanation] It indicates that the request cannot be accepted because BV contains linked SV.
aaa...a : Logical disk name of relevant volume
[Measures] Remove the link of relevant volume (unlink) and re-execute.
Chapter 2 Message List
569
iSM19110: The volume of SV guard exists.
[SV:<aaa...a>]
[Classification] ERROR
[Explanation] It indicates that the request cannot be accepted because BV contains protected
SV.
aaa...a : Logical disk name of relevant volume
[Measures] Deactivate the protection for relevant volume and re-execute.
iSM19111: Version of API is invalid.
[Classification] ERROR
[Explanation] API version is invalid.
[Measures] Use the API with the correct version.
iSM19112: Specified volume is wrong.
[{BV|SV}:<aaa...a>]
[Classification] ERROR
[Explanation] There is an error in the specified volume.
The specified volume does not exist or the attribute (BV or SV) does not match.
aaa...a : Volume name
[Measures] Check the specified volume name and re-execute.
Chapter 2 Message List
570
iSM19113: Volume list does not exist.
[Classification] ERROR
[Explanation] Volume list is invalid. Or, the volume list version is not correct.
[Measures] Re-create the volume list.
iSM19114: License for snapshot is locked.
[Classification] ERROR
[Explanation] The snapshot product has not been purchased.
[Measures] Purchase the product to perform snapshot operation.
iSM19115: Snapshot function is not supported
with this volume.
[Classification] ERROR
[Explanation] The snapshot function is not supported.
[Measures] Snapshot cannot be used.
iSM19116: Specified drive number does not
exist.
[Classification] ERROR
[Explanation] Disk with the specified disk number does not exist. This message is output on
Windows system.
[Measures] Check the specified physical drive and re-execute.
Chapter 2 Message List
571
iSM19117: Specified drive type is not
supported.(type=<aaa...a>)
[Classification] ERROR
[Explanation] Specified drive type is not supported. This message is output on Windows
system.
aaa...a : Drive type
Dynamic Disk. : Dynamic disk
GPT Partition Disk. : GPT partition disk
Multi Partition Disk. : Multi partition disks
[Measures] Partition disk with the GPT (GUID Partition Table) format cannot be used.
iSM19118: Specified volume does not exist in
volume list. [{BV|SV}:<aaa...a>]
[Classification] ERROR
[Explanation] Specified volume does not exist in the volume list.
aaa...a : Volume name
[Measures] Check the volume and re-execute or re-create a volume list.
iSM19119: Volume list data is locked by another
process.
[Classification] ERROR
[Explanation] Volume list is being created/updated by another process.
[Measures] After completion of a process, retry command execution.
Chapter 2 Message List
572
iSM19120: The operation to the volume specified
is forbidden. (type=<aaa...a>)
[Classification] ERROR
[Explanation] The command was issued to the volume of which OS type is not supported. This
message is output on Windows system.
aaa...a : OS type
[Measures] Check the OS type and re-execute.
iSM19121: SV is not omissible.(Two or more
SV(s) exist)
[Classification] ERROR
[Explanation] SV was omitted at execution for BV built with multiple SVs. You should
specify the parameter to identify an SV if several SVs exist.
[Measures] Specify SV and re-execute.
iSM19122: The volume under execution of
replication function cannot be
specified. [BV:<aaa...a>]
[Classification] ERROR
[Explanation] It indicates that the request cannot be accepted because the replication function is
copying data in the specified volume.
aaa...a : Volume name
[Measures] Check the volume and re-execute.
Chapter 2 Message List
573
iSM19123: The volume which is not recognized
cannot be specified. [BV:<aaa...a>]
[Classification] ERROR
[Explanation] It indicates that the request cannot be accepted because the command was issued
to the volume invisible to the self host.
aaa...a : Volume name
[Measures] Check the volume and re-execute.
iSM19124: SV of snap/inactive is already exist.
[Classification] INFO
[Explanation] The SV with snapshot inactive (snap/inactive) already exists.
[Measures] Unnecessary
iSM19125: Snapshot has been nullified.
[Classification] INFO
[Explanation] It indicates that snapshot was nullified because an old snapshot is restored.
Snapshot data is no longer accessible once snapshot is nullified.
[Measures] Unnecessary
iSM19126: Specified SV has been deleted.
[SV:<aaa...a>]
[Classification] INFO
[Explanation] Specified SV has already been deleted.
aaa...a : Volume name
[Measures] Unnecessary
Chapter 2 Message List
574
iSM19127: Request has already completed.
[Classification] INFO
[Explanation] It indicates that the request is already satisfied.
[Measures] Unnecessary
iSM19200: Mandatory option was not specified.
(<aaa...a>)
[Classification] ERROR
[Explanation] Specified command does not have some required arguments, or invalid
arguments are specified. When -file option is specified, an unavailable option is
specified for the pair specified by the snapshot operation file.
aaa...a : Specified value
[Measures] Specify the necessary arguments in the command line. If -file option is specified,
check the snapshot operation file.
iSM19202: Illegal option value was specified.
(<aaa...a>)
[Classification] ERROR
[Explanation] Specified option is invalid.
aaa...a : Specified value
[Measures] Specify a correct option.
Chapter 2 Message List
575
iSM19203: Number of BV and SV was not equal.
[Classification] ERROR
[Explanation] The number of volumes specified for BV and SV is different. This message is
output on UNIX system.
[Measures] Make the number of BV and SV volumes equal.
iSM19208: Illegal configuration was detected.
(file=<aaa...a>,line=<bbb...b>)
[Classification] ERROR
[Explanation] Specified file contains invalid settings.
aaa...a : File name
bbb...b : Number of lines
[Measures] Correct the file and re-execute.
iSM19209: Illegal option value was
detected.(file=<aaa...a>,line=<bbb...b
>)
[Classification] ERROR
[Explanation] Specified file contains invalid options.
aaa...a : File name
bbb...b : Number of lines
[Measures] Correct the file and re-execute.
Chapter 2 Message List
576
iSM19210: Number of BV and SV was not equal.
(file =<aaa...a>,line=<bbb...b>)
[Classification] ERROR
[Explanation] The number of volumes specified for BV and SV is different.
aaa...a : File name
bbb...b : Number of lines
[Measures] Make the number of BV and SV volumes equal.
iSM19212: Duplicated targets were detected.
(file=<aaa...a>,line=<bbb...b> )
[Classification] WARNING
[Explanation] Specified pair information is defined repeatedly.
aaa...a : Volume name
bbb...b : Number of lines
[Measures] Check the volume specification.
iSM19213: Illegal volume flag was specified to be
(<aaa...a>) option.(manager
specification)
[Classification] ERROR
[Explanation] Specified volume type is invalid.
aaa...a : Specified option
[Measures] Check the specified volume type. Operations linked with snapshot management
allow specifying logical disk name and relative generation.
Chapter 2 Message List
577
iSM19301: The unexpected error has occurred in
iSM/Server. (code=aaa...a/bb/ccc...c)
[Classification] ERROR
[Explanation] An unexpected error has occurred.
aaa...a : Process number
bb : Detail information (This code is not disorder reason but a value
for maintenance.)
ccc...c : Error detail code
[Measures] Abnormality was found in message from iSM server. Check status of iSM server.
iSM19302: Specified Diskarray does not exist.
[Classification] ERROR
[Explanation] Specified disk array is not under iSM control.
[Measures] Check that the specified disk array is under iSM control.
iSM19303: State of Diskarray includes specified
volume is not monitoring.
[Classification] ERROR
[Explanation] Monitoring of specified volume disk array is suspended.
[Measures] Start disk array monitoring.
iSM19304: Timeout error has occurred in
iSM/Server.
[Classification] ERROR
[Explanation] Time-out occurred in process of iSM server.
[Measures] Loads on iSM server may be too heavy. Check status of iSM server and
re-execute.
Chapter 2 Message List
578
iSM19305: The timeout was detected by waiting
of communication with iSM/Server.
[Classification] ERROR
[Explanation] Time-out occurred in socket exclusive control.
[Measures] Another process may control the socket. Check status of iSM server and
re-execute.
iSM19306: Failed to connect
iSM/Server.(errno=<aaa...a>, phase=<
bbb...b>)
[Classification] ERROR
[Explanation] Failed in connecting the socket.
aaa...a : System call error number
bbb...b : Error detail code
[Measures] Check status of iSM server.
iSM19307: Failed to receive from
iSM/Server.(errno=<aaa...a>,
phase=<bbb...b>)
[Classification] ERROR
[Explanation] Failed in receiving messages from iSM server.
aaa...a : System call error number
bbb...b : Error detail code
[Measures] Check connection status of iSM server.
Chapter 2 Message List
579
iSM19308: Failed to send to
iSM/Server.(errno=<aaa...a>,
phase=<bbb...b>)
[Classification] ERROR
[Explanation] Failed in sending messages to iSM server.
aaa...a : System call error number
bbb...b : Error detail code
[Measures] Check connection status of iSM server.
iSM19401: System call error has
occurred.(func=<aaa...a>,
errno=<bbbb>, phase=<ccc...c>)
[Classification] ERROR
[Explanation] System call failed.
aaa...a : Erroneous system function name
bbb…b : System call error number
ccc…c : Error detail code
[Measures] If operation trace data has been collected, troubleshoot on the basis of operation
trace data and error number, and then remove cause of fault.
iSM19402: Unexpected error occurred.
(phase=<aaa...a>)
[Classification] ERROR
[Explanation] An unexpected error has occurred.
aaa...a : Error detail code
[Measures] Check the details and re-execute.
Chapter 2 Message List
580
iSM19403: Failed to mount.
[Classification] ERROR
[Explanation] Mounting failed. This message is output on Windows system.
[Measures] Check the message displayed immediately before to handle it.
iSM19404: Failed to umount.
[Classification] ERROR
[Explanation] Unmounting failed. This message is output on Windows system.
[Measures] Check the message displayed immediately before to handle it.
iSM19405: Collecting information of display was
failed.
[Classification] ERROR
[Explanation] Failed in acquiring display information.
[Measures] Re-execute the command.
iSM19408: Data on SV has been removed.
[SV:<aaa...a>]
[Classification] INFO
[Explanation] It indicates that the iSMsc_restore command has deleted the snapshot newer than
the restored one.
aaa...a : Logical disk name
[Measures] Unnecessary
Chapter 2 Message List
581
iSM20000 ∼
iSM20000: <aaa...a>
[Classification] INFO
[Explanation] Executed command line.
aaa...a : Entered character string
[Measures] Unnecessary
iSM20010: iSMsc_chgmod has normally
terminated.
[Classification] INFO
[Explanation] iSMsc_chgmod command normal termination message.
[Measures] Unnecessary
iSM20011: iSMsc_chgmod has normally
terminated. [vol:<aaa...a>]
[Classification] INFO
[Explanation] iSMsc_chgmod command normal termination message.
aaa...a : Volume name
[Measures] Unnecessary
iSM20012: iSMsc_chgmod has abnormally
terminated.
[Classification] INFO
[Explanation] iSMsc_chgmod command abnormal termination message.
[Measures] Check the message displayed immediately before to handle it.
Chapter 2 Message List
582
iSM20013: iSMsc_chgmod has abnormally
terminated. [vol:<aaa...a>]
[Classification] ERROR
[Explanation] iSMsc_chgmod command abnormal termination message.
aaa...a : Volume name
[Measures] Check the message displayed immediately before to handle it.
iSM20020: iSMsc_link has normally terminated.
[Classification] INFO
[Explanation] iSMsc_link command normal termination message.
[Measures] Unnecessary
iSM20021: iSMsc_link has normally terminated.
[LV:<aaa...a>] [SV:<bbb...b>]
[Classification] INFO
[Explanation] iSMsc_link command normal termination message.
aaa...a : Volume name
bbb...b : Volume name
[Measures] Unnecessary
iSM20022: iSMsc_link has abnormally
terminated.
[Classification] INFO
[Explanation] iSMsc_link command abnormal termination message.
[Measures] Check the message displayed immediately before to handle it.
Chapter 2 Message List
583
iSM20023: iSMsc_link has abnormally terminated.
[LV:<aaa...a>] [SV:<bbb...b>]
[Classification] INFO
[Explanation] iSMsc_link command abnormal termination message.
aaa...a : Volume name
bbb...b : Volume name
[Measures] Check the message displayed immediately before to handle it.
iSM20030: iSMsc_unlink has normally
terminated.
[Classification] INFO
[Explanation] iSMsc_unlink command normal termination message.
[Measures] Unnecessary
iSM20031: iSMsc_unlink has normally terminated.
[LV:<aaa...a>][SV:<bbb...b>]
[Classification] INFO
[Explanation] iSMsc_unlink command normal termination message.
aaa...a : Volume name
bbb...b : Volume name
[Measures] Unnecessary
Chapter 2 Message List
584
iSM20032: iSMsc_unlink has abnormally
terminated.
[Classification] INFO
[Explanation] iSMsc_unlink command abnormal termination message.
[Measures] Check the message displayed immediately before to handle it.
iSM20033: iSMsc_unlink has abnormally
terminated.
[LV:<aaa...a>][SV:<bbb...b>]
[Classification] INFO
[Explanation] iSMsc_unlink command abnormal termination message.
aaa...a : Volume name
bbb...b : Volume name
[Measures] Check the message displayed immediately before to handle it.
iSM20100: Unpaired volumes cannot be specified.
[SV:<aaa...a>]
[Classification] ERROR
[Explanation] It indicates that the request cannot be accepted because the specified volume has
no pair setting.
aaa...a : Volume name
[Measures] Check the status with the query command and re-execute.
Chapter 2 Message List
585
iSM20101: The volume from which capacity is
different cannot be specified.
[LV:<aaa...a>] [{BV|SV}:<bbb...b>]
[Classification] ERROR
[Explanation] It indicates that the request cannot be accepted because the capacity of LV is
different from that of BV or SV.
aaa...a : Volume name
bbb...b : Volume name
[Measures] Check the volume capacity and re-execute.
iSM20102: The Volume from which volume type
is different type cannot be specified.
[LV:<aaa...a>] [{BV|SV}:<bbb...b>]
[Classification] ERROR
[Explanation] It indicates that the request cannot be accepted because the OS type of LV is
different from that of BV or SV.
aaa...a : Volume name
bbb...b : Volume name
[Measures] Check the volume capacity and re-execute.
iSM20103: Specified volume has another link.
[{LV|BV|SV}:<aaa...a>]
[Classification] ERROR
[Explanation] It indicates that the request cannot be accepted because the volume is already
linked.
aaa...a : Volume name of relevant volume
[Measures] Check the link status and re-execute.
Chapter 2 Message List
586
iSM20104: State of SV's access mode is invalid.
(mode=<aaa...a>) [SV:<bbb...b>]
[Classification] ERROR
[Explanation] It indicates that the request cannot be accepted because the access restriction of
specified volume is not "Not Ready".
aaa...a : Access restriction of specified volume
rw : Input/output allowed
ro : Read only
na : Access prohibited
bbb...b : Volume name
[Measures] Change the access restriction to "Not Ready" and re-execute.
iSM20106: Targets volumes are not linked.
[LV:<aaa...a>] [{BV|SV}:<bbb...b>]
[Classification] ERROR
[Explanation] Specified volume is not linked.
aaa...a : Volume name
bbb...b : Volume name
[Measures] Check the link status of specified volume and re-execute.
iSM20107: The volume mounted cannot be
specified. [LV:<aaa...a>]
[Classification] ERROR
[Explanation] The link cannot be removed because specified volume is mounted.
aaa...a : Volume name of LV
[Measures] Check the status of specified volume and re-execute.
Chapter 2 Message List
587
iSM20108: SV which is not snap/active cannot be
specified. [SV:<aaa...a>]
[Classification] ERROR
[Explanation] Link cannot be set because SV with snapshot inactive is specified as link
connection volume.
aaa...a : Volume name
[Measures] Check the SV status and re-execute.
iSM20109: The volume which is not link target
volume cannot be specified.
[{BV|SV}:<aaa...a>]
[Classification] ERROR
[Explanation] Specified volume is not to be linked to LV.
aaa...a : Volume name
[Measures] Register the connection volume to the link control list and re-execute.
iSM20112: Specified volume is wrong.
[{LV|BV|SV|VOL}:<aaa...a>]
[Classification] ERROR
[Explanation] There is an error in the specified volume.
The specified volume does not exist or the attribute (BV or SV) does not match.
aaa...a : Volume name
[Measures] Check the specified volume name and re-execute.
Chapter 2 Message List
588
iSM20116: Version of API is invalid.
[Classification] ERROR
[Explanation] API version is invalid.
[Measures] Use the API with the correct version.
iSM20117: License for snapshot is locked.
[Classification] ERROR
[Explanation] The snapshot product has not been purchased.
[Measures] Purchase the product to perform snapshot operation.
iSM20118: Snapshot function is not supported
with this volume.
[Classification] ERROR
[Explanation] The snapshot function is not supported.
[Measures] Snapshot cannot be used.
iSM20119: Specified volume does not exist in
volume list.
[{BV|SV|LV|VOL}:<aaa...a>]
[Classification] ERROR
[Explanation] Specified volume does not exist in the volume list.
aaa...a : Volume name
[Measures] Check the volume and re-execute or re-create a volume list.
Chapter 2 Message List
589
iSM20120: Link information does not exist.
[VOL:<aaa...a>]
[Classification] ERROR
[Explanation] The command cannot be executed because the specified volume is neither LV
nor link target volume.
aaa...a : Volume name
[Measures] Check the volume and re-execute.
iSM20121: The volume which is not recognized
cannot be specified. [BV:<aaa...a>]
[Classification] ERROR
[Explanation] It indicates that the request cannot be accepted because the command was issued
to the volume invisible to the self host.
aaa...a : Volume name
[Measures] Check the volume and re-execute.
iSM20122: The volume which is not linked
cannot be specified. [VOL:<aaa...a>]
[Classification] ERROR
[Explanation] It indicates that the request cannot be accepted because the specified volume is
not linked.
aaa...a : Volume name
[Measures] Check the link status and re-execute.
Chapter 2 Message List
590
iSM20123: State of specified diskarray is 'freeze'.
[Classification] ERROR
[Explanation] The disk array where specified volume is stored is in the freeze state.
[Measures] Cancel the freeze state and re-execute.
iSM20200: Mandatory option was not
specified.(<aaa...a>)
[Classification] ERROR
[Explanation] Specified command does not have some required options. () may or may not be
displayed.
aaa...a : Option name
[Measures] Specify the necessary arguments in the command line.
iSM20201: Illegal option was specified.(<aaa...a>)
[Classification] ERROR
[Explanation] Specified option is invalid or options that cannot be specified at the same time
are specified.
aaa...a : Option name
[Measures] Specify a correct option.
iSM20202: Illegal option value was
specified.(<aaa...a>)
[Classification] ERROR
[Explanation] Specified option is invalid.
aaa...a : Specified value
[Measures] Specify a correct value.
Chapter 2 Message List
591
iSM20203: Specified volume group does not
exist.(vg=<aaa...a>)
[Classification] ERROR
[Explanation] Specified volume group is invalid.
aaa...a : Volume group
[Measures] Specify a correct volume group.
iSM20204: Specified disk group does not
exist.(dg=<aaa...a>)
[Classification] ERROR
[Explanation] Specified disk group is invalid.
aaa...a : Disk group
[Measures] Specify a correct disk group.
iSM20205: Duplicated targets were detected.
(file=<aaa...a>, line=<bbb...b> )
[Classification] WARNING
[Explanation] Specified pair information is defined repeatedly.
aaa...a : File name
bbb...b : Number of lines
[Measures] Check the volume specification.
Chapter 2 Message List
592
iSM20206: Specified file does not exist.
(file=<aaa...a>)
[Classification] ERROR
[Explanation] Specified file does not exist.
aaa...a : File name
[Measures] Specify a correct file name.
iSM20207: Specified file is invalid.(illegal file
type) (file=<aaa...a>)
[Classification] ERROR
[Explanation] The specified file type cannot be processed.
aaa...a : File name
[Measures] Specify the file created by the regular file. (UNIX)
Specify a file created as a text file. (Windows)
iSM20208: Illegal configuration was detected.
(file=<aaa...a>, line=<bbb...b>)
[Classification] ERROR
[Explanation] Specified file contains invalid settings.
aaa...a : File name
bbb…b : Number of lines
[Measures] Correct the file and re-execute.
Chapter 2 Message List
593
iSM20209: Illegal option value was detected.
(file=<aaa...a>, line=<bbb...b>)
[Classification] ERROR
[Explanation] Specified file contains invalid options.
[Measures] Correct the file and re-execute.
iSM20210: Empty file cannot be specified.
(file=<aaa...a>)
[Classification] ERROR
[Explanation] Specified file is empty.
aaa...a : File name
[Measures] Check the file and re-execute.
iSM20211: Illegal volume flag was specified to be
(<aaa...a>) option.(manager
specification)
[Classification] ERROR
[Explanation] Specified volume type is invalid.
aaa...a : Specified option
[Measures] Check the specified volume type. Operations linked with snapshot management
allow specifying logical disk name and relative generation.
Chapter 2 Message List
594
iSM20301: The unexpected error has occurred in
iSM/Server. (code=aaa...a/bb/ccc...c)
[Classification] ERROR
[Explanation] An unexpected error has occurred.
aaa...a : Process number
bb : Detail information (This code is not disorder reason but a value
for maintenance.)
ccc...c : Error detail code
[Measures] Abnormality was found in message from iSM server. Check status of iSM server.
iSM20302: Specified Diskarray does not exist.
[Classification] ERROR
[Explanation] Specified disk array is not under iSM control.
[Measures] Check that the specified disk array is under iSM control.
iSM20303: State of Diskarray includes specified
volume is not monitoring.
[Classification] ERROR
[Explanation] Monitoring of specified volume disk array is suspended.
[Measures] Start disk array monitoring.
Chapter 2 Message List
595
iSM20304: Timeout error has occurred in
iSM/Server.
[Classification] ERROR
[Explanation] Time-out occurred in process of iSM server.
[Measures] Loads on iSM server may be too heavy. Check status of iSM server and
re-execute.
iSM20305: The timeout was detected by waiting
of communication with iSM/Server.
[Classification] ERROR
[Explanation] Time-out occurred in socket exclusive control.
[Measures] Another process may control the socket. Check status of iSM server and
re-execute.
iSM20306: Failed to connect
iSM/Server.(errno=<aaa...a>,
phase=<bbb...b>)
[Classification] ERROR
[Explanation] Failed in connecting the socket.
aaa...a : System call error number
bbb...b : Error detail code
[Measures] Check status of iSM server.
Chapter 2 Message List
596
iSM20307: Failed to receive from
iSM/Server.(errno=<aaa...a>,
phase=<bbb...b>)
[Classification] ERROR
[Explanation] Failed in receiving messages from iSM server.
aaa...a : System call error number
bbb...b : Error detail code
[Measures] Check connection status with iSM server.
iSM20308: Failed to send to
iSM/Server.(errno=<aaa...a>,
phase=<bbb...b>)
[Classification] ERROR
[Explanation] Failed in sending messages from iSM server.
aaa...a : System call error number
bbb...b : Error detail code
[Measures] Check connection status with iSM server.
iSM20401: System call error has
occurred.(func=<aaa...a>,
errno=<bbbb>, phase=<ccc…c>)
[Classification] ERROR
[Explanation] System call failed.
aaa...a : Erroneous system function name
bbbb : System call error number
ccc...c : Error detail code
[Measures] If operation trace data has been collected, troubleshoot on the basis of operation
trace data and error number, and then remove cause of fault.
Chapter 2 Message List
597
iSM20402: Unexpected error occurred.
(phase=<aaa...a>)
[Classification] ERROR
[Explanation] An unexpected error has occurred.
aaa...a : Error detail code
[Measures] Check the details and re-execute.
iSM20403: SCSI I/O error is detected.
(device=aaaa, cdb
=bbbb,status=cccc/dddd/ee/ff/gg)
[Classification] ERROR
[Explanation] An error has occurred during SCSI command execution.
aaa...a : Failed device name
bbbb : Command Descriptor Block of issued command
cccc : SCSI command execution result
dddd : SCSI sense result
ee : SCSI sense information SenseKey
ff : SCSI sense information SenseCode
gg : SCSI sense information Qualifier
[Measures] Re-execute the command.
Chapter 2 Message List
598
iSM20404: Control path is blockaded.
(device=aaaa, cdb
=bbbb,status=cccc/dddd/ee/ff/gg)
[Classification] WARNING
[Explanation] Paths are switched.
aaa...a : Failed device name
bbbb : Command Descriptor Block of issued command
cccc : SCSI command execution result
dddd : SCSI sense result
ee : SCSI sense information SenseKey
ff : SCSI sense information SenseCode
gg : SCSI sense information Qualifier
[Measures] Unnecessary
iSM20405: Illegal device is specified. (<aaa...a>)
[Classification] ERROR
[Explanation] Specified device is invalid.
aaa...a : The following error detail information
No such Device. : Specified device cannot be found.
Not character device. : Specified device is not a character
device.
Not path through device. : The SCSI path through device
corresponding to the specified
device cannot be found.
[Measures] Check the parameter details and re-execute.
Chapter 2 Message List
599
iSM20406: Failed to umount.
[Classification] ERROR
[Explanation] Unmounting failed.
This message is output on Windows system.
[Measures] Check the message displayed immediately before to handle it.
Chapter 2 Message List
600
iSM99000 ∼
iSM99001: Connected with iSM server
(Server=<aaa...a>, Port=<bbb...b>,
User=<ccc...c>, Client=<ddd...d>)
[Classification] INFO
[Explanation] It has connected with the server (internal message of iSM client).
aaa...a : Server name
bbb...b : Port name
ccc...c : User name
ddd...d : Client name
iSM99002: Disconnected with iSM server
(Server=<aaa...a>, Port=<bbb...b>,
User=<ccc...c>, Client=<ddd...d>)
[Classification] INFO
[Explanation] It was disconnected with the server (internal message of iSM client).
aaa...a : Server name
bbb...b : Port name
ccc...c : User name
ddd...d : Client name
Chapter 2 Message List
601
iSMnetconf: 001 ∼
iSMnetconf: 001 Command complete
successfully.
[Classification] INFO
[Explanation] Succeeded in command execution.
[Measures] Unnecessary
iSMnetconf: 101 Command has failed. (<aaa...a>)
[Classification] INFO
[Explanation] Failed in SCSI command execution.
aaa...a : Additional information
[Measures] Service processor was not set correctly. Check that no problem exists in the
specified parameter, or the connection between host and disk array is normal.
iSMnetconf: 111 Internal error has occurred.
(<aaa...a>)
[Classification] INFO
[Explanation] An internal error occurred.
aaa...a : Additional information
[Measures] Service processor was not set correctly. Check that no problem exists in
operating environment of this command, and connection between host and disk
array is normal.
Chapter 2 Message List
602
iSMnetconf: 112 Changed to the alternative path.
(<aaa...a>)
[Classification] INFO
[Explanation] Switched to alternative path.
aaa...a : Additional information
[Measures] Unnecessary
iSMnetconf: 201 Resource does not exist.
(<aaa...a>)
[Classification] INFO
[Explanation] Applicable resource does not exist.
aaa...a : Additional information
[Measures] Check that service processor has been installed.
iSMnetconf: 202 Many target resources exist.
[Classification] INFO
[Explanation] Two or more applicable resources exist.
[Measures] Specify an applicable resource.
iSMnetconf: 203 Only root can execute.
[Classification] INFO
[Explanation] Execution is allowed for root-authorized user only.
[Measures] Execute by a root-authorized user.
Chapter 2 Message List
603
iSMnetconf: 211 Specified Disk Array Subsystem
is not supported. (<aaa...a>)
[Classification] INFO
[Explanation] Specified disk array is not supported by this program.
aaa...a : Additional information
[Measures] Specify a special file that indicates disk array that is applicable to this program.
iSMnetconf: 212 Specified Disk Array Subsystem
is set by another maintenance tool.
(<aaa...a>)
[Classification] INFO
[Explanation] Specified disk array is being set by other tool.
aaa...a : Additional information
[Measures] For executing this program, terminate the setting by other tool.
iSMnetconf: 221 Specified option is illegal.
(<aaa...a>)
[Classification] INFO
[Explanation] Specified option is invalid.
aaa...a : Additional information
[Measures] Specify a valid option.
Chapter 2 Message List
604
iSMnetconf: 222 Specified parameter is illegal.
(<aaa...a>)
[Classification] INFO
[Explanation] Specified parameter is invalid.
aaa...a : Additional information
[Measures] Specify a valid parameter.
iSMnetconf: 223 Specified IP Address is alive.
(<aaa...a>)
[Classification] INFO
[Explanation] Specified IP address is being used by other network device.
aaa...a : Additional information
[Measures] Specify an IP address that is not used by other network device.
iSMnetconf: 224 Specified IP Address is illegal.
(<aaa...a>)
[Classification] INFO
[Explanation] Specified IP address is invalid.
aaa...a : Additional information
[Measures] Specify a valid IP address.
Chapter 2 Message List
605
iSMnetconf: 225 Specified Subnet Mask is illegal.
(<aaa...a>)
[Classification] INFO
[Explanation] Specified subnet mask is invalid.
aaa...a : Additional information
[Measures] Specify a valid subnet mask.
iSMnetconf: 226 Specified Gateway Address is
illegal. (<aaa...a>)
[Classification] INFO
[Explanation] Specified gateway address is invalid.
aaa...a : Additional information
[Measures] Specify a valid gateway address.
iSMnetconf: 227 Specified IP Address is
duplicated. (<aaa...a>)
[Classification] INFO
[Explanation] Specified IP address is duplicated.
aaa...a : Additional information
[Measures] The same IP address cannot be specified by multiple parameters. Specify an IP
address with no duplication.
Chapter 2 Message List
606
iSMnetconf: 228 Specified IP Address is already
registered. (<aaa...a>)
[Classification] INFO
[Explanation] Specified IP address has already been registered.
aaa...a : Additional information
[Measures] Specify an IP address that has not yet been registered.
iSMnetconf: 229 Specified IP Address is not
registered. (<aaa...a>)
[Classification] INFO
[Explanation] Specified IP address has not been registered.
aaa...a : Additional information
[Measures] Specify an IP address that has already been registered.
iSMnetconf: 230 An IP Address cannot be
registered any more. (<aaa...a>)
[Classification] INFO
[Explanation] No more IP addresses can be specified
aaa...a : Additional information
[Measures] No more IP addresses can be specified because the number of IP addresses to be
registered to disk array will be exceeded.
Chapter 2 Message List
607
iSMnetconf: 241 Specified file cannot be read.
[Classification] INFO
[Explanation] Specified file cannot be read.
[Measures] Check that specified file name is correct and authority to access file is given.
iSMnetconf: 242 File format is illegal. (<aaa...a>)
[Classification] INFO
[Explanation] File format is illegal.
aaa...a : Additional information
[Measures] Check that setting file format is correct.
Chapter 2 Message List
608
iSMprfarc: 101 ∼
iSMprfarc: 101 Not PSL file -- <aaa...a>
[Explanation] The specified file is not a statistic info file.
aaa...a : Specified file name
[Measures] Specify the correct file.
iSMprfarc: 102 Can’t open file -- <aaa...a>
func=<bbb...b> errno=<cccc>
[Explanation] The input file or output file cannot be opened.
aaa...a : Name of the file to be opened
bbb...b : Name of the function where the error occurred
cccc : Error number
[Measures] Specify a correct file, or specify an appropriate access right.
iSMprfarc: 103 Can’t open directory -- <aaa...a>
func=<bbb...b> errno=<cccc>
[Explanation] The specified directory cannot be opened.
aaa...a : Name of the file to be opened
bbb...b : Name of the function where the error occurred
cccc : Error number
[Measures] Specify a correct directory, or specify an appropriate access right.
iSMprfarc: 104 Invalid option -- <aaaa>
[Explanation] The specified option is erroneous.
aaaa : Specified option
[Measures] Specify the correct option.
Chapter 2 Message List
609
iSMprfarc: 105 Can’t input multi-level file
[Explanation] Statistic information history files and statistic information primary summarized
files cannot be mixed.
[Measures] Specify either statistic information history files or statistic information primary
summarized files.
iSMprfarc: 106 Out of range -- <aaaa>
[Explanation] The specified target period of summarizing is erroneous. Any periods prior to
1970 or in the future cannot be specified.
aaaa : Specified target period of summarizing
[Measures] Specify the correct target period of summarizing.
iSMprfarc: 107 Can’t find target file
[Explanation] The specified directory does not contain the statistic info files corresponding to
the target period of summarizing.
[Measures] Specify a correct directory or target period of summarizing.
iSMprfarc: 108 No more archiving -- <aaa...a>
[Explanation] Statistic information secondary summarized files cannot be summarized.
aaa...a : Name of the specified file
[Measures] Specify either statistic information history files or statistic information primary
summarized files.
iSMprfarc: 109 Can’t allocate memory
[Explanation] Sufficient memory to perform summarizing process cannot be reserved.
[Measures] Remove the cause of insufficient memory, or check whether the specified
statistic info file is damaged or not.
Chapter 2 Message List
610
iSMprfarc: 110 Read error -- <aaa...a>
func=<bbb...b> errno=<cccc>
[Explanation] Read of the statistic info file failed.
aaa...a : Name of the file which was read
bbb...b : Name of the function where the error occurred
cccc : Error number
[Measures] Remove the cause of read failure, or check whether the specified statistic info
file is damaged or not.
iSMprfarc: 111 Write error -- <aaa...a>
func=<bbb...b> errno=<cccc>
[Explanation] Write to the output file failed.
aaa...a : Name of the file which to be written
bbb...b : Name of the function where the error occurred
cccc : Error number
[Measures] Remove the cause of write failure.
iSMprfarc: 112 Record broken [-- <aaa...a>]
[Explanation] The record of the input statistic info file is damaged.
aaa...a : Specified file name
[Measures] Damaged statistic info files cannot be summarized. Remove them from the
target files.
Chapter 2 Message List
611
iSMprfarc: 120 Illegal file format -- <aaa...a>
[Explanation] The specified file is a wrong file that is not the statistic information history
file/statistic information summarized file, or a statistic information file of
unprocessable version.
aaa...a : Name of the wrong file
[Measures] Check the specified file.
iSMprfarc: 201 Warning: Find discontinuous file
[Explanation] A period where statistic information is discontinuous is detected in secondary
summarizing or direct secondary summarizing. Some files may be missing. It
is assumed that the configuration change occurred, and summarizing process
continues.
[Measures] Check if the target files are complete.
iSMprfctl 001 ∼
iSMprfctl 001: Command completed
successfully
[Explanation] The command was executed successfully.
[Measures] Unnecessary
iSMprfctl 010: Missing option -- <aaa...a>
[Explanation] The mandatory option has not been specified.
aaa...a : Name of the mandatory option
[Measures] Specify the mandatory option, and then re-execute the command.
Chapter 2 Message List
612
iSMprfctl 011: Illegal option -- <aaa...a>
[Explanation] An illegal option was specified.
aaa...a : Name of the illegal option
[Measures] Specify the correct option, and then re-execute the command.
iSMprfctl 012: Missing option value -- <aaa...a>
[Explanation] No value has been specified in the option.
aaa...a : Name of the option in which no value has been specified
[Measures] Specify a value in the option, and then re-execute the command.
iSMprfctl 013: Illegal option value -- <aaa...a>
<bbb...b>
[Explanation] The specified option contains an illegal value.
aaa...a : Name of the option containing an illegal value
bbb...b : Specified value
[Measures] Specify a correct value in the option, and then re-execute the command.
iSMprfctl 020: iSMsvr is not ready
[Explanation] The iSM server has not started.
[Measures] Start the iSM server, and then re-execute the command.
Chapter 2 Message List
613
iSMprfctl 021: Specified Disk Array is invalid
[Explanation] The command cannot be executed for the specified disk array because of the
following:
y The specified disk array is not one to be monitored by iSM.
y The specified disk array is not permitted to use the performance optimization
function.
[Measures] Check for the specified disk array name or the available product status.
iSMprfctl 022: Specified Disk Array is not
monitored
[Explanation] Monitoring of the specified disk array has stopped, and the command cannot be
executed.
[Measures] Restart the monitoring of the disk array, and then re-execute the command.
iSMprfctl 023: Specified Disk Array is not in
normal state
[Explanation] The specified disk array is not in normal state, and the command cannot be
executed.
[Measures] Rebuild the disk array, and then re-execute the command.
Chapter 2 Message List
614
iSMprfctl 030: Specified Logical Disk is invalid
[Explanation] The specification of the logical disk to be moved is invalid.
Check:
y if the specified logical disk exists in the specified disk array.
y if the specified logical disk is defined as a work disk for optimization.
y if the specified logical disk is defined as a cache resident disk.
[Measures] Review the specification of the logical disk to be moved, and then re-execute the
command.
iSMprfctl 031: Specified Optimization Work Disk
is invalid
[Explanation] The specification of the work disk for optimization is invalid.
Check:
y if the specified work disk for optimization exists in the specified disk array.
y if the attributes of the specified work disk for optimization are correct.
y if the specified work disk for optimization is defined as a cache resident disk.
[Measures] Review the specification of the work disk for optimization, and then re-execute
the command.
iSMprfctl 032: Disk Capacity is different
[Explanation] The logical disk to be moved and the work disk for optimization have a different
capacity, and the logical disk cannot be moved.
[Measures] Review the specification of the logical disk to be moved and the work disk for
optimization, and then re-execute the command.
Chapter 2 Message List
615
iSMprfctl 033: Specified Logical Disk is multi
rank type
[Explanation] The specified logical disk to be moved is a multi-RANK disk, and it cannot be
moved.
[Measures] Review the specification of the logical disk to be moved, and then re-execute the
command.
iSMprfctl 035: Specified Logical Disk and
Optimization Work Disk are in the
same rank
[Explanation] The logical disk to be moved and the work disk for optimization exist in the
same RANK, and the logical disk cannot be moved.
[Measures] Review the specification of the logical disk to be moved and the work disk for
optimization, and then re-execute the command.
iSMprfctl 036: Specified Logical Disk name
overlaps
[Explanation] The name of the specified logical disk to be moved is identical to the name of
another disk in the specified disk array.
[Measures] Correct the volume format specification of the logical disk to be moved, and then
re-execute the command.
Chapter 2 Message List
616
iSMprfctl 037: Specified Optimization Work Disk
name overlaps
[Explanation] The name of the specified work disk for optimization is identical to the name of
another disk in the specified disk array.
[Measures] Correct the volume format specification of the work disk for optimization, and
then re-execute the command.
iSMprfctl 040: Specified Logical Disk is under
moving
[Explanation] The specified logical disk to be moved is already moving.
[Measures] Review the specification of the logical disk to be moved, and then re-execute the
command.
iSMprfctl 041: Specified Optimization Work Disk
is under moving
[Explanation] The specified work disk for optimization is already moving.
[Measures] Review the specification of the work disk for optimization, and then re-execute
the command.
iSMprfctl 042: Specified Logical Disk is not in
normal state
[Explanation] The specified logical disk to be moved is not in normal state, and it cannot be
moved.
[Measures] Rebuild the logical disk to be moved, and then re-execute the command.
Chapter 2 Message List
617
iSMprfctl 043: Specified Optimization Work Disk
is not in normal state
[Explanation] The specified work disk for optimization is not in normal state, and it cannot be
moved.
[Measures] Rebuild the work disk for optimization or specify another one, and then
re-execute the command.
iSMprfctl 044: Number of movement exceeds
permissible amount
[Explanation] The number of specified disks to be concurrently moved exceeded the allowable
maximum in the specified disk array.
[Measures] Confirm that the current Move command has terminated, and then re-execute the
command.
iSMprfctl 045: Specified Logical Disk is reserved
[Explanation] It indicates that specified moving material logical disk has been reserved in
schedule.
[Measures] Review the moving material logical disk and retry command execution.
iSMprfctl 046: Specified Optimization Work Disk
is reserved
[Explanation] It indicates that specified work disk for optimization has been reserved in
schedule.
[Measures] Review the specified work disk for optimization and retry command execution.
Chapter 2 Message List
618
iSMprfctl 050: Failed in communication with
iSMsvr func=<aaa...a> errno=
<bbbb> detcode=<cccccccc>
[Explanation] An error occurred during communication with the iSM server.
aaa...a : Function name
bbbb : Error code
cccccccc : Detail code
[Measures] Eliminate the error cause (e.g., restarting the iSM server), and then re-execute the
command.
iSMprfctl 051: Time out has occurred
[Explanation] A timeout occurred during communication with the iSM server.
[Measures] Check for the iSM server status, restart the iSM server if necessary, and then
re-execute the command.
iSMprfctl 060: Insufficient resource is detected
func=<aaa...a> errno=<bbbb>
detcode=<cccccccc>
[Explanation] Memory could not be allocated.
aaa...a : Function name
bbbb : Error code
cccccccc : Detail code
[Measures] Eliminate the error cause, and then re-execute the command.
Chapter 2 Message List
619
iSMprfctl 090: HW error has occurred in start of
Logical Disk movement
[Explanation] An error occurred in the disk array, and moving of the logical disk failed to start.
[Measures] Check the error cause according to the related messages, recover the disk array
from the error, and then re-execute the command.
iSMprfctl 910: Illegal function parameter
[Explanation] An illegal subcommand was specified.
[Measures] Correct the specification of the subcommand, and then re-execute the command.
Chapter 2 Message List
620
iSMprfedit: 001 ∼
iSMprfedit: 001 <aaa...a> > <bbb...b>
[Explanation] The performance information of the statistical information history file or
statistical information summary file was edited and output as a report normally.
aaa...a : Name of the statistical information history file or statistical
information summary file (character string)
bbb...b : Name of the Performance Report (text format file) (character
string)
[Measures] Unnecessary
iSMprfedit: 100 Illegal option - <aaa...a>
[Explanation] It indicates that a wrong option was specified.
aaa...a : Name of the wrong option (String)
[Measures] Specify the option correctly and execute the command again.
iSMprfedit: 101 Illegal file name - <aaa...a>
[Explanation] It indicates that the name of the specified file is invalid (other than psl and psa).
aaa...a : Invalid file name (String)
[Measures] Correct the file name and execute the command again.
iSMprfedit: 102 Missing file name
[Explanation] It indicates that statistic info file is not specified.
[Measures] Specify statistic info file and execute the command again.
Chapter 2 Message List
621
iSMprfedit: 103 Missing option - <aaa...a>
[Explanation] It indicates that required option is not specified.
aaa...a : Option name required to be specified (String)
[Measures] Specify the option correctly and execute the command again.
iSMprfedit: 110 File open error - <aaa...a>
func = <bbb...b> errno = <cccc> ds
= <dddddddd>
[Explanation] It indicates that an error occurred in the open process of the file.
aaa...a : Name of the file for which the error occurred in the open process
(String)
bbb...b : Name of the function where the error occurred (String)
cccc : Error number (in Decimal)
dddddddd : Detailed code of the error (in Hexadecimal)
[Measures] Remove the cause of the open error based on the name of the function where the
error occurred and the error number, and execute the command again.
iSMprfedit: 111 File close error - <aaa...a>
func = <bbb...b> errno = <cccc> ds
= <dddddddd>
[Explanation] It indicates that an error occurred in the close process of the file.
aaa...a : Name of the file for which the error occurred in the close process
(String)
bbb...b : Name of the function where the error occurred (String)
cccc : Error number (in Decimal)
dddddddd : Detailed code of the error (in Hexadecimal)
[Measures] Remove the cause of the close error based on the name of the function where the
error occurred and the error number, or change the location where the edit report
is created by specifying the -o option, and execute the command again.
Chapter 2 Message List
622
iSMprfedit: 112 Read error - <aaa...a> func =
<bbb...b> errno = <cccc> ds =
<dddddddd>
[Explanation] It indicates that an error occurred in the input process of the file.
aaa...a : Name of the file for which the error occurred in the input process
(String)
bbb...b : Name of the function where the error occurred (String)
cccc : Error number (in Decimal)
dddddddd : Detailed code of the error (in Hexadecimal)
[Measures] Remove the cause of the read error based on the name of the function where the
error occurred and the error number, and execute the command again.
iSMprfedit: 113 Write error - <aaa...a> func =
<bbb...b> errno = <cccc> ds =
<dddddddd>
[Explanation] It indicates that an error occurred in the write process of the file.
aaa...a : Name of the file for which the error occurred in the write process
(String)
bbb...b : Name of the function where the error occurred (String)
cccc : Error number (in Decimal)
dddddddd : Detailed code of the error (in Hexadecimal)
[Measures] Remove the cause of the write error based on the name of the function where the
error occurred and the error number, or change the location where the edit report
is created by specifying the -o option, and execute the command again.
iSMprfedit: 114 Sort error - <aaa...a> func =
<bbb...b> errno = <cccc> ds =
<dddddddd>
[Explanation] It indicates that an error occurred in the sort process of the data.
aaa...a : Name of the file for which the error occurred in the sort process
(String)
bbb...b : Name of the function where the error occurred (String)
cccc : Error number (in Decimal)
dddddddd : Detailed code of the error (in Hexadecimal)
[Measures] Remove the cause of the error based on the function name and the error number,
and execute the command again.
Chapter 2 Message List
623
iSMprfedit: 115 Memory allocate error -
<aaa...a> func = <bbb...b> errno =
<cccc> ds = <dddddddd>
[Explanation] It indicates that an error occurred in memory allocation process.
aaa...a : Name of the file for which the error occurred in the memory
allocation process (String)
bbb...b : Name of the function where the error occurred (String)
cccc : Error number (in Decimal)
dddddddd : Detailed code of the error (in Hexadecimal)
[Measures] Remove the cause of the memory allocation error based on the name of the
function where the error occurred and the error number, and execute the
command again.
iSMprfedit: 120 Illegal file format - <aaa...a>
ds = <bbbbbbbb>
[Explanation] It indicates that a wrong file other than statistic information history file/statistic
information summarized file is specified.
aaa...a : Name of the wrong file (String)
bbbbbbbb : Detailed code of the error (in Hexadecimal)
[Measures] Specify the correct file, and execute the command again.
iSMprfedit: 121 Data empty - <aaa...a>
[Explanation] It indicates that the specified statistic information history file/statistic
information summarized file does not contain statistic information to be edited.
aaa...a : Name of the specified statistic information history file/statistic
information summarized file (String)
[Measures] Specify the correct file, and execute the command again.
Chapter 2 Message List
624
iSMprfedit: 122 Since there is no data of
<aaa...a>, <aaa...a> performance
report has not been created -
<bbb...b>
[Explanation] It indicates that specified statistic information history file/statistic information
summarized file does not contain the statistic information of the performance
detail report, and specified performance detail report could not be created.
aaa...a : Component type of which detailed report could not be created.
(String)
Replication Director Port : Replication director port
Cache Segment : Cache segment
Rank : RANK
Pool : Pool
bbb...b : Name of specified statistic information history file/statistic
information summarized file (String)
[Measures] Take the measures below.
- If the component type is replication director port, a disk array with no function
for collecting statistic information of the replication director port does not
contain replication director port statistic information in statistic information
history file/statistic information summarized file. Review parameters and
retry command execution.
- If component type is cache segment, a disk array that cannot use cache
partitioning function does not contain cache segment statistic information in
statistic information history file. Review parameters and retry command
execution.
- If component type is RANK, a disk array with no function for collecting
RANK statistic information does not contain RANK statistic information in
statistic information history file/statistic information summarized file.
Review parameters and retry command execution.
- If the component type is pool, a disk array with no function for collecting pool
statistic information does not contain pool statistic information in statistic
information history file/statistic information summarized file. Review
parameters and retry command execution.
Chapter 2 Message List
625
iSMprfedit: 999 Unexpected error - <aaa...a>
ds = <bbbbbbbb>
[Explanation] It indicates that an error occurred in the internal processing of iSMprfedit.
aaa...a : Name of the specified statistic information history file/statistic
information summarized file (String)
bbbbbbbb : Detailed code of the error (in Hexadecimal)
[Measures] Execute the command again.
Chapter 2 Message List
626
iSMprfext: 001 ∼
iSMprfext: 001 <aaa...a> > <bbb...b>
[Explanation] The statistical information of the statistical information history file or statistical
information summary file was converted into CSV format and output as a CSV
format file normally.
aaa...a : Name of the statistical information history file or statistical
information summary file (character string)
bbb...b : Name of the output file (CSV format file) (character string)
[Measures] Unnecessary
iSMprfext: 002 Illegal option - <aaa...a>
[Explanation] It indicates that a wrong option was specified or some mandatory options are not
specified.
aaa...a : Name of the option with wrong specification (String)
[Measures] Correct the specification of the option and execute the command again.
iSMprfext: 003 Illegal option value - <aaa...a>
[Explanation] It indicates that the value of the specified option is invalid.
aaa...a : Name of the option with invalid value (String)
-hp : Specification of host director port
-rp : Specification of replication director port
-dp : Specification of disk director port
-cheseg : Specification of cache segment
-ld : Specification of logical disk
-pd : Specification of physical disk
-rank : Specification of RANK
-pool : Specification of pool
[Measures] Correct the value of the option, and execute the command again.
Chapter 2 Message List
627
iSMprfext: 004 File open error - <aaa...a>
func = <bbb...b> errno = <cccc>
[Explanation] It indicates that an error occurred in the open process of the file.
aaa...a : Name of the file for which the error occurred in the open process
(String)
bbb...b : Name of the function where the error occurred (String)
cccc : Error number (in Decimal)
[Measures] Check file specification and access right of the file. Then, remove the cause of
the error, and execute the command again.
iSMprfext: 005 File close error - <aaa...a>
func = <bbb...b> errno = <cccc>
[Explanation] It indicates that an error occurred in the close process of the file.
aaa...a : Name of the file for which the error occurred in the close process
(String)
bbb...b : Name of the function where the error occurred (String)
cccc : Error number (in Decimal)
[Measures] Check the file system to remove the cause of the error or specify the -p option to
change the location for output files, and execute the command again.
iSMprfext: 006 Read error - <aaa...a> func =
<bbb...b> errno = <cccc> ds =
<dddddddd>
[Explanation] It indicates that an error occurred in the input process of the file.
aaa...a : Name of the file for which the error occurred in the input process
(String)
bbb...b : Name of the function where the error occurred (String)
cccc : Error number (in Decimal)
dddddddd : Detailed code of the error (in Hexadecimal)
[Measures] Check whether the specified statistic information history file/statistic information
summarized file is damaged or not.
Chapter 2 Message List
628
iSMprfext: 007 Write error - <aaa...a> func =
<bbb...b> errno = <cccc>
[Explanation] It indicates that an error occurred in the write process of the file.
aaa...a : Name of the file for which the error occurred in the write process
(String)
bbb...b : Name of the function where the error occurred (String)
cccc : Error number (in Decimal)
[Measures] Check the file system to remove the cause of the error or specify the ‘-p’ option
to change the location for output files, and execute the command again.
iSMprfext: 008 Illegal file format - <aaa...a>
ds = <bbbbbbbb>
[Explanation] It indicates that a wrong file other than statistic information history file/statistic
information summarized file is specified.
aaa...a : Name of the wrong file (String)
bbbbbbbb : Detailed code of the error (in Hexadecimal)
[Measures] Specify the correct file, and execute the command again.
iSMprfext: 009 Data empty - <aaa...a>
[Explanation] It indicates that the specified statistic information history file/statistic
information summarized file does not contain statistic information to be
converted to the CSV format.
aaa...a : Name of the specified statistic information history file/statistic
(String)
[Measures] If any extraction conditions are specified, check the conditions and execute the
command again.
Chapter 2 Message List
629
iSMprfext: 010 Unexpected error - <aaa...a>
ds = <bbbbbbbb>
[Explanation] It indicates that an error occurred in the internal processing of CSV Conversion
Tool.
aaa...a : Name of the specified statistic information history file/statistic
information summarized file (String)
bbbbbbbb : Detailed code of the error (in Hexadecimal)
[Measures] Execute the command again.
iSMprfext: 011 Record count is over max
value - <aaa...a>
[Explanation] It indicates that the number of records of the output file (in the CSV format)
exceeded the upper limit (65,536 records).
aaa...a : Name of the output file (CSV file) (String)
[Measures] Specify some extraction conditions to limit statistic information to extract, and
execute the command again.
Chapter 2 Message List
630
iSMprflog:001 ∼
iSMprflog:001 Disk array=<aaa...a> logging is
started interval=<bb>
[Explanation] It indicates that data accumulation in statistic information history file has been
started.
aaa...a : Disk array name
bb : Accumulating interval (minute)
[Measures] Unnecessary
iSMprflog:002 Disk array=<aaa...a> logging is
already started
[Explanation] It indicates that data accumulation in statistic information history file has already
been started.
aaa...a : Disk array name
[Measures] Check that specified disk array name is correct.
iSMprflog:003 Disk array=<aaa...a> logging is
started(overload) interval=<bb>
[Explanation] It indicates that data accumulation in statistic information history file has been
started. By collecting statistic information, disk array is overloaded.
aaa...a : Disk array name
bb : Accumulating interval (minute)
[Measures] Terminate accumulation if overloading on disk array affect business operations.
Chapter 2 Message List
631
iSMprflog:010 Disk array=<aaa...a> logging is
stopped
[Explanation] It indicates that data accumulation in statistic information history file has been
terminated.
aaa...a : Disk array name
[Measures] Unnecessary
iSMprflog:011 Disk array=<aaa...a> logging is
already stopped
[Explanation] It indicates that data accumulation in statistic information history file has been
already terminated.
aaa...a : Disk array name
[Measures] Unnecessary
iSMprflog:100 Missing option - <aaaaa>
[Explanation] It indicates that option has not been specified.
aaaaa : Option name which should be specified
[Measures] Specify required option and retry command execution.
iSMprflog:101 Illegal option - <aaaaa>
[Explanation] It indicates that specified option was wrong.
aaaaa : Specified value
[Measures] Specify required option correctly and retry command execution.
Chapter 2 Message List
632
iSMprflog:102 Missing option value - <aaaaa>
[Explanation] It indicates that value of -aaaaa option has not been specified.
aaaaa : Specified value
[Measures] Specify required option value and retry command execution.
iSMprflog:103 Illegal option value - <aaaaa>
[Explanation] It indicates that an invalid option value has been specified.
aaaaa : Option name with invalid value
[Measures] Specify correct option value and retry command execution.
iSMprflog:104 Illegal function parameter
[Explanation] It indicates that a wrong parameter except “start” or “stop” was specified.
[Measures] Specify correct parameter and retry command execution.
iSMprflog:120 Disk array=<aaa...a> is not
watched
[Explanation] It indicates that specified disk array is not monitored.
aaa...a : disk array name
[Measures] Specify the disk array for monitoring and start or terminate accumulating statistic
information.
iSMprflog:121 Disk array=<aaa...a> does not
exist
[Explanation] It indicates that specified disk array does not exist, or the PerformanceMonitor
has not been purchased.
aaa...a : Disk array name
[Measures] Specify correct disk array name.
Chapter 2 Message List
633
iSMprflog:122 There is no disk array
[Explanation] It indicates that target disk array does not exist when batch operation is executed
for all the disk array with -a option specified.
[Measures] Check status of disk array, and retry command if necessary.
iSMprflog:123 Disk array=<aaa...a> is overload
[Explanation] It indicates that accumulation of statistic information could not start due to the
following reasons:
(1) Disk array is overloaded.
(2) Disk array faulty.
aaa...a : Disk array name
[Measures] Take the following measures:
Against case (1) above: Remove the causes of overloading, and start
accumulation of statistic information in statistic
information history file.
Against case (2) above: Stop monitoring and start troubleshooting. And then
restart monitoring, and perform accumulation of
statistic information in statistic information history
file.
iSMprflog:900 System call error occurred
func=<aaa...a> errno=<bbb>
detail=<cc-ddd>
[Explanation] It indicates that an error occurred in system function.
aaa...a : System function name
bbb : Error number
cc-ddd : Error description
[Measures] Take measures with reference to function name and error number, and then retry
command execution.
Appendix A Message Output Destination List
634
Appendix A Message Output Destination
List
This appendix lists the destinations of messages output by iSM.
Table A-1 Message Output Destination List (1/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM01001 INFO { ∆ {
{
iSM01002 INFO { { { ∆ {
{
iSM01003 INFO { ∆ {
{
iSM01004 WARNING { {
iSM01005 INFO { ∆
iSM01006 WARNING { { { {
iSM01010 INFO { ∆ {
{
iSM01011 INFO { { { ∆ {
{
iSM01101 WARNING { { { { {
iSM01102 NOTICE { { {
iSM01103 NOTICE { { { { {
iSM01105 NOTICE { { {
iSM01106 NOTICE { { { { {
iSM01107 WARNING { { { { {
{
iSM01108 NOTICE { {
iSM01109 WARNING { { { { {
{
iSM01110 NOTICE { { {
iSM01111 NOTICE { { {
iSM01113 NOTICE {
iSM01230 WARNING { { {
{
iSM01232 ERROR { {
iSM01400 -
{
iSM01401 -
{
iSM01402 -
{
iSM01403 -
{
iSM01407 -
{
iSM01408 -
{
iSM01409 -
{
iSM01410 -
{
iSM01411 -
{
iSM01412 -
{
iSM01413 -
{
iSM01901 ERROR {
iSM02010 NOTICE { { { {
iSM02011 NOTICE { { { {
iSM02020 NOTICE { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
635
Table A-1 Message Output Destination List (2/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM02021 NOTICE { { {
iSM02040 INFO { { { ∆
iSM02041 INFO { { { ∆
iSM02042 NOTICE { { { {
iSM02043 NOTICE { { { {
iSM02050 INFO { { { ∆
iSM02051 INFO { { { ∆
iSM02052 INFO { { { ∆
iSM02053 INFO { { ∆
iSM02060 NOTICE { {
iSM02061 NOTICE { {
iSM03100 WARNING { { { {
iSM03101 WARNING { { { {
iSM03102 ERROR { { { { {
iSM03103 ERROR { { { { {
iSM03104 ERROR { { { { {
iSM03105 ERROR { { { { {
iSM03106 ERROR { { { { {
iSM03107 ERROR { { { { {
iSM03108 ERROR { { { { {
iSM03109 ERROR { { { { {
iSM03110 ERROR { { { { {
iSM03111 ERROR { { { { {
iSM03112 ERROR { { { { {
iSM03113 WARNING { { { {
iSM03114 WARNING { { { {
iSM03120 INFO { { { ∆
iSM03121 WARNING { { { {
iSM03122 INFO { { { ∆
iSM03130 NOTICE { { { {
iSM03131 NOTICE { { { {
iSM03132 NOTICE { { { {
iSM03133 NOTICE { { { {
iSM03134 NOTICE { { { {
iSM03140 NOTICE { { { {
iSM03141 NOTICE { { { {
iSM03142 NOTICE { { { {
iSM03150 INFO { { { ∆
iSM03151 INFO { { { ∆
iSM03152 INFO { { { ∆
iSM03200 ERROR { { { {
iSM03201 ERROR { { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
636
Table A-1 Message Output Destination List (3/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM03203 ERROR { { { {
iSM03204 ERROR { { { {
iSM03220 ERROR { { {
iSM03221 ERROR { { { {
iSM03222 ERROR { { { {
iSM03224 ERROR { { { { { { {
iSM03225 ERROR { { {
iSM03300 INFO { { { ∆
iSM03301 INFO { { { ∆
iSM03302 WARNING { { { {
iSM03303 INFO { { { ∆
iSM03400 ERROR { { { {
iSM03410 ERROR { { { {
iSM03411 ERROR { { { {
iSM03420 ERROR { { { {
iSM03430 ERROR { { { {
iSM03441 ERROR { { {
iSM03442 ERROR { {
iSM03500 ERROR { { { {
iSM03900 WARNING {
iSM04020 NOTICE { { { {
iSM04021 NOTICE { { { {
iSM04022 WARNING { {
iSM04023 ERROR { { { {
iSM04024 ERROR { { { {
iSM04025 ERROR { { { {
iSM04030 INFO { { { ∆
iSM04040 WARNING { { { {
iSM04060 INFO { {
iSM06020 NOTICE { { { {
iSM06021 NOTICE { { { {
iSM06029 WARNING { { { {
iSM06030 WARNING { { { {
iSM06031 WARNING { { { {
iSM06032 WARNING { { { {
iSM06033 WARNING { { { {
iSM06034 WARNING { { { {
iSM06035 WARNING { { { {
iSM06036 WARNING { { { {
iSM06037 WARNING { { { {
iSM06038 WARNING { { { {
iSM06039 WARNING { { { {
iSM06040 WARNING { { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
637
Table A-1 Message Output Destination List (4/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM06041 WARNING { { { {
iSM06042 WARNING { { { {
iSM06043 WARNING { { { {
iSM06044 WARNING { { { {
iSM06045 WARNING { { { {
iSM06047 WARNING { { { {
iSM06048 WARNING { { { {
iSM06050 WARNING { { { {
iSM06051 WARNING { { { {
iSM06062 WARNING { { { {
iSM06063 WARNING { { { {
iSM06064 WARNING { { { {
iSM06065 WARNING { { { {
iSM06066 WARNING { { { {
iSM06068 WARNING { { { {
iSM06070 WARNING { {
iSM06071 WARNING { {
iSM06080 INFO { { { ∆ {
iSM06081 WARNING { { { { {
iSM06082 WARNING { { { { {
iSM06083 ERROR { { { {
iSM06084 ERROR { { { {
iSM06085 ERROR { { { {
iSM06086 WARNING { { { {
iSM06087 WARNING { { { {
iSM06088 WARNING { { { {
iSM06091 WARNING { { { {
iSM06092 WARNING { { { {
iSM06093 WARNING { { { {
iSM06099 WARNING { { { {
iSM06902 ERROR {
iSM07011 INFO { { { ∆ {
{
iSM07012 INFO { { { ∆ { { {
iSM07021 INFO { { { ∆ {
{
iSM07022 INFO { { { ∆ {
{
iSM07023 ERROR { { { { { { {
iSM07024 ERROR { { { { { { {
iSM07025 INFO { { { ∆ {
{
iSM07026 ERROR { { { { { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
638
Table A-1 Message Output Destination List (5/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM07031 INFO { { { ∆
iSM07032 INFO { { { ∆
iSM07033 INFO { { { ∆
iSM07034 INFO { { { ∆
iSM07035 INFO { { { ∆
iSM07091 WARNING { { { {
iSM07092 WARNING { { { {
iSM07093 ERROR { { { {
iSM07094 ERROR { { { {
iSM07095 ERROR { { { {
iSM07101 INFO { { { ∆
iSM07102 ERROR { { { { {
{
iSM07104 NOTICE { { { { {
{
iSM07105 NOTICE { { { {
iSM07106 NOTICE { { { {
iSM07108 ERROR { { { {
iSM07109 INFO { { { ∆ {
{
iSM07111 INFO { { { ∆
iSM07112 ERROR { { { { {
{
iSM07113 ERROR { { { {
iSM07114 NOTICE { { { {
iSM07115 NOTICE { { { {
iSM07116 NOTICE { { { {
iSM07121 INFO { { { ∆
iSM07122 ERROR { { { {
iSM07123 ERROR { { { { {
{
iSM07124 ERROR { { { {
iSM07125 NOTICE { { { {
iSM07126 NOTICE { { { {
iSM07127 NOTICE { { { {
iSM07128 NOTICE { { { {
iSM07129 NOTICE { { { {
iSM07130 NOTICE { { { {
iSM07131 NOTICE { { { {
iSM07132 NOTICE { { { {
iSM07133 INFO { { { ∆
iSM07141 INFO { { { ∆
iSM07142 ERROR { { { { {
{
iSM07143 ERROR { { { {
iSM07144 NOTICE { { { {
iSM07145 NOTICE { { { {
iSM07146 NOTICE { { { {
iSM07147 NOTICE { { { {
iSM07148 NOTICE { { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
639
Table A-1 Message Output Destination List (6/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM07151 INFO { { { ∆
iSM07152 ERROR { { { { { { {
iSM07154 NOTICE { { { { { { {
iSM07155 NOTICE { { { {
iSM07156 NOTICE { { { {
iSM07158 ERROR { { { {
iSM07159 INFO { { { ∆ { { {
iSM07161 INFO { { { ∆
iSM07162 ERROR { { { { { { {
iSM07163 ERROR { { { {
iSM07164 NOTICE { { { {
iSM07165 NOTICE { { { {
iSM07166 NOTICE { { { {
iSM07171 INFO { { { ∆
iSM07172 ERROR { { { {
iSM07173 ERROR { { { { { { {
iSM07174 ERROR { { { {
iSM07175 NOTICE { { { {
iSM07176 NOTICE { { { {
iSM07177 NOTICE { { { {
iSM07178 NOTICE { { { {
iSM07179 NOTICE { { { {
iSM07180 NOTICE { { { {
iSM07181 NOTICE { { { {
iSM07182 NOTICE { { { {
iSM07183 INFO { { { ∆
iSM07191 INFO { { { ∆
iSM07192 ERROR { { { { { { {
iSM07193 ERROR { { { {
iSM07194 NOTICE { { { {
iSM07195 NOTICE { { { {
iSM07196 NOTICE { { { {
iSM07197 NOTICE { { { {
iSM07198 NOTICE { { { {
iSM07201 INFO { { { ∆
iSM07202 INFO { { { ∆
iSM07203 INFO { { { ∆
iSM07204 INFO { { { ∆
iSM07205 NOTICE { { { {
iSM07206 NOTICE { { { {
iSM07207 NOTICE { { { {
iSM07208 NOTICE { { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
640
Table A-1 Message Output Destination List (7/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM07211 INFO { {
iSM07212 INFO { {
iSM07213 INFO { {
iSM07220 INFO { { { ∆
iSM07221 INFO { { { ∆
iSM07251 WARNING { { { {
iSM07252 WARNING { { { {
iSM07253 WARNING { { { {
iSM07301 INFO { { { ∆
iSM07302 INFO { { { ∆
iSM07303 INFO { { { ∆
iSM07304 INFO { { { ∆
iSM07305 INFO { { { ∆
iSM07306 INFO { { { ∆
iSM07307 INFO { { { ∆
iSM07308 INFO { { { ∆
iSM07309 INFO { { { ∆
iSM07310 INFO { { { ∆
iSM07311 INFO { { { ∆
iSM07312 INFO { { { ∆
iSM07313 INFO { { { ∆
iSM07314 INFO { { { ∆
iSM07315 INFO { { { ∆
iSM07316 INFO { { { ∆
iSM07331 INFO { {
iSM07332 INFO { {
iSM07333 INFO { {
iSM07334 INFO { {
iSM07335 INFO { {
iSM07336 INFO { {
iSM07337 INFO { {
iSM07338 INFO { {
iSM07339 INFO { {
iSM07340 INFO { {
iSM07341 INFO { {
iSM07342 INFO { {
iSM07343 INFO { {
iSM07344 INFO { {
iSM07345 INFO { {
iSM07346 INFO { {
iSM07402 INFO { { { ∆ {
{
iSM07404 NOTICE { { { {
iSM07409 INFO { { { ∆
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
641
Table A-1 Message Output Destination List (8/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM07411 INFO { { { ∆
iSM07412 ERROR { { { { {
{
iSM07413 ERROR { { { {
iSM07414 NOTICE { { { {
iSM07415 NOTICE { { { {
iSM07416 NOTICE { { { {
iSM07452 INFO { { { ∆ { { {
iSM07454 NOTICE { { { {
iSM07459 INFO { { { ∆
iSM07461 INFO { { { ∆
iSM07462 ERROR { { { { { { {
iSM07463 ERROR { { { {
iSM07464 NOTICE { { { {
iSM07465 NOTICE { { { {
iSM07466 NOTICE { { { {
iSM07501 -
{
iSM07503 -
{
iSM07504 -
{
iSM07505 -
{
iSM07506 -
{
iSM07507 -
{
iSM07509 -
{
iSM07511 -
{
iSM07512 -
{
iSM07513 -
{
iSM07550 NOTICE { { { { {
iSM07551 NOTICE { { { { {
iSM07552 NOTICE { { { { {
iSM07553 NOTICE { { { { {
iSM07554 NOTICE { { { { {
iSM07555 NOTICE { { { { {
iSM07556 NOTICE { { { { {
iSM07557 -
{
iSM07601 NOTICE { { { {
iSM07602 NOTICE { { { {
iSM07611 NOTICE { { { {
iSM07616 WARNING { { { { {
{
iSM07617 INFO { { { {
iSM07620 INFO { { { ∆ {
{
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
642
Table A-1 Message Output Destination List (9/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM07621 NOTICE { { { { {
{
iSM07622 ERROR { { { { {
{
iSM07670 INFO { { { ∆ { { {
iSM07671 NOTICE { { { { { { {
iSM07672 ERROR { { { { { { {
iSM07900 WARNING {
iSM07950 WARNING { { { { {
iSM07981 NOTICE { { { {
iSM08020 INFO { {
iSM08021 INFO { {
iSM08022 NOTICE { {
iSM08030 NOTICE { {
iSM08031 NOTICE { {
iSM08032 NOTICE { {
iSM08033 NOTICE { {
iSM08034 NOTICE {
iSM08035 NOTICE { {
iSM08036 NOTICE { {
iSM08037 NOTICE { {
iSM08050 WARNING { { { { {
iSM08051 NOTICE { { { {
iSM08052 NOTICE { {
iSM08053 NOTICE { {
iSM08054 NOTICE { {
iSM08055 WARNING { {
iSM08056 WARNING { {
iSM08060 WARNING { {
iSM08061 WARNING { {
iSM08062 WARNING { {
iSM08063 INFO { {
iSM08070 NOTICE { {
iSM08071 NOTICE { {
iSM08072 NOTICE { {
iSM08091 NOTICE { {
iSM08092 NOTICE { {
iSM08093 NOTICE { {
iSM08094 NOTICE { { { {
iSM08099 NOTICE { {
iSM08180 NOTICE { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
643
Table A-1 Message Output Destination List (10/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM08181 NOTICE { { {
iSM08182 NOTICE { { {
iSM08183 NOTICE { { {
iSM08201 NOTICE { {
iSM08900 WARNING {
iSM09001 NOTICE { { { {
iSM09002 NOTICE { {
iSM09003 NOTICE { {
iSM09004 NOTICE { {
iSM09005 NOTICE { {
iSM09006 NOTICE { {
iSM09007 NOTICE { {
iSM09008 NOTICE { {
iSM09009 NOTICE { {
iSM09010 NOTICE { {
iSM09011 NOTICE { {
iSM09012 NOTICE { {
iSM09013 NOTICE { {
iSM09014 NOTICE { {
iSM09015 NOTICE { {
iSM09016 NOTICE { {
iSM09017 NOTICE { {
iSM09018 NOTICE { {
iSM09019 NOTICE { {
iSM09020 NOTICE { {
iSM09021 NOTICE { {
iSM09022 NOTICE { {
iSM09099 NOTICE { {
iSM09101 WARNING { {
iSM09102 WARNING { {
iSM09103 WARNING { {
iSM09104 WARNING { {
iSM09105 WARNING { {
iSM09106 WARNING { {
iSM09107 WARNING { {
iSM09108 WARNING { {
iSM10001 NOTICE { { { {
iSM10002 NOTICE { { { {
iSM10020 ERROR { { { {
iSM10040 NOTICE { { { {
iSM10100 NOTICE { { { {
iSM10101 NOTICE { { { {
iSM10102 NOTICE { { { {
iSM10103 ERROR { { { {
iSM10104 NOTICE { { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
644
Table A-1 Message Output Destination List (11/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM10106 NOTICE { { { {
iSM10200 NOTICE { { { {
iSM10201 NOTICE { { { {
iSM10210 NOTICE { { { {
iSM10220 ERROR { { { {
iSM10302 INFO { { { ∆
iSM10303 INFO { { { ∆
iSM10304 INFO { { { ∆
iSM10305 INFO { { { ∆
iSM10306 INFO { { { ∆
iSM10307 INFO { { { ∆
iSM10308 INFO { { { ∆ {
iSM10309 INFO { { { ∆ {
iSM10310 NOTICE { { { {
iSM10311 NOTICE { { { {
iSM10312 NOTICE { { { { {
iSM10313 NOTICE { {
iSM10314 NOTICE { {
iSM10315 NOTICE { {
iSM10316 NOTICE { {
iSM10317 NOTICE { { { { {
iSM10318 NOTICE { {
iSM10320 ERROR { { { {
iSM10321 NOTICE { { { { {
iSM10322 NOTICE { { { { {
iSM10323 NOTICE { {
iSM10324 NOTICE { {
iSM10325 NOTICE { {
iSM10330 NOTICE { { { {
iSM10331 INFO { { { ∆
iSM10332 INFO { { { ∆
iSM10333 INFO { { { ∆
iSM10334 INFO { { { ∆
iSM10400 ERROR { { { { {
{
iSM10401 ERROR { { { { { { {
iSM10402 WARNING { { { { {
{
iSM10403 ERROR { { { { { { {
iSM10410 NOTICE { { { {
iSM10411 NOTICE { { { {
iSM10420 NOTICE { { { {
iSM10430 ERROR { { { {
iSM10440 NOTICE { { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
645
Table A-1 Message Output Destination List (12/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM10501 ERROR {
iSM10502 ERROR {
iSM10503 ERROR {
iSM10504 ERROR {
iSM10505 ERROR {
iSM10900 WARNING { { { {
iSM11100 INFO { { { ∆ {
iSM11101 INFO { { {
iSM11102 INFO { {
iSM11103 INFO { { {
iSM11104 INFO { {
iSM11105 INFO { { {
iSM11106 INFO { {
iSM11107 INFO { {
iSM11108 INFO { {
iSM11109 INFO { {
iSM11110 INFO { {
iSM11151 INFO { { {
iSM11152 INFO {
iSM11153 INFO { { {
iSM11154 INFO { { {
iSM11155 INFO { { {
iSM11161 INFO { { {
iSM11162 INFO { { {
iSM11163 INFO { { {
iSM11164 INFO { { {
iSM11171 INFO { { {
iSM11172 INFO { { {
iSM11173 INFO { { {
iSM11174 INFO { { {
iSM11175 INFO { { {
iSM11176 INFO { { {
iSM11178 INFO { { {
iSM11179 INFO { { {
iSM11180 INFO { { {
iSM11182 INFO { { {
iSM11183 INFO { { {
iSM11184 INFO { { {
iSM11220 INFO { {
iSM11221 INFO { {
iSM11222 INFO { {
iSM11230 INFO {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
646
Table A-1 Message Output Destination List (13/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM11231 INFO {
iSM11232 INFO {
iSM11233 INFO {
iSM11234 INFO {
iSM11235 INFO { { {
iSM11236 INFO { { {
iSM11237 INFO {
iSM11240 INFO { {
iSM11241 INFO {
iSM11242 INFO { {
iSM11250 INFO {
iSM11251 INFO {
iSM11252 INFO {
iSM11253 INFO {
iSM11255 INFO {
iSM11257 INFO {
iSM11258 INFO {
iSM11300 INFO {
iSM11305 INFO {
iSM11306 INFO {
iSM11307 INFO {
iSM11308 INFO {
iSM11309 INFO {
iSM11310 INFO {
iSM11311 INFO {
iSM11320 INFO {
iSM11321 INFO {
iSM11322 INFO {
iSM11323 INFO {
iSM11300 INFO {
iSM11340 INFO {
iSM11360 INFO {
iSM11361 INFO { { {
iSM11362 INFO {
iSM11363 INFO {
iSM11364 INFO {
iSM11365 INFO {
iSM11366 INFO { { {
iSM11367 INFO { { {
iSM11369 INFO {
iSM11370 INFO {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
647
Table A-1 Message Output Destination List (14/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM11372 INFO {
iSM11373 INFO {
iSM11374 INFO {
iSM11375 INFO {
iSM11376 INFO {
iSM11377 INFO {
iSM11378 INFO {
iSM11379 INFO {
iSM11380 INFO {
iSM11381 INFO {
iSM11382 INFO {
iSM11383 INFO {
iSM11384 INFO {
iSM11385 INFO {
iSM11402 INFO { {
iSM11403 INFO { {
iSM11404 INFO { {
iSM11405 INFO { {
iSM11406 INFO { { {
iSM11407 INFO { {
iSM11408 INFO { {
iSM11409 INFO { {
iSM11410 INFO { {
iSM11412 INFO { {
iSM11413 INFO { {
iSM11414 INFO { {
iSM11415 INFO { {
iSM11416 INFO { {
iSM11417 INFO { {
iSM11419 INFO { {
iSM11420 INFO { {
iSM11421 INFO { {
iSM11422 INFO { {
iSM11423 INFO { {
iSM11424 INFO { {
iSM11425 INFO { {
iSM11426 INFO { {
iSM11429 INFO { {
iSM11431 INFO { {
iSM11438 INFO { {
iSM11439 INFO { {
iSM11440 INFO { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
648
Table A-1 Message Output Destination List (15/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM11442 INFO { {
iSM11443 INFO { {
iSM11444 INFO { {
iSM11455 INFO { {
iSM11486 INFO { {
iSM11487 INFO { {
iSM11501 INFO { {
iSM11502 INFO { {
iSM11503 INFO { {
iSM11504 INFO { {
iSM11505 INFO { {
iSM11506 INFO { {
iSM11507 INFO { {
iSM11508 INFO { {
iSM11509 INFO { {
iSM11510 INFO { {
iSM11521 INFO {
iSM11522 INFO {
iSM11531 INFO { {
iSM11532 INFO { {
iSM11533 INFO { {
iSM11534 INFO { {
iSM11535 INFO { {
iSM11536 INFO { {
iSM11537 INFO { {
iSM11538 INFO { {
iSM11539 INFO { {
iSM11540 INFO { {
iSM11542 INFO { { {
iSM11543 INFO { { {
iSM11544 INFO { { {
iSM11545 INFO { { {
iSM11546 INFO { { {
iSM11548 ERROR { { { { {
iSM11549 ERROR { { { { {
iSM11557 ERROR { { { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
649
Table A-1 Message Output Destination List (16/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM11561 INFO { {
iSM11562 INFO { {
iSM11563 INFO { {
iSM11564 INFO { {
iSM11565 INFO { {
iSM11566 INFO { {
iSM11567 INFO { {
iSM11568 INFO { {
iSM11569 INFO { {
iSM11570 INFO { {
iSM11571 INFO { {
iSM11572 INFO { {
iSM11573 INFO { {
iSM11574 INFO { {
iSM11575 INFO { {
iSM11576 INFO { {
iSM11577 INFO { {
iSM11578 INFO { {
iSM11579 INFO { {
iSM11580 INFO { {
iSM11581 INFO { {
iSM11582 INFO { {
iSM11583 INFO { {
iSM11584 INFO { {
iSM11585 INFO { {
iSM11586 INFO { {
iSM11587 INFO { {
iSM11600 INFO {
iSM11601 INFO {
iSM11602 INFO {
iSM11603 INFO {
iSM11604 INFO {
iSM11605 INFO {
iSM11700 INFO { { { ∆ {
iSM11701 INFO { { { ∆ { {
iSM11702 ERROR { { { { { {
iSM11703 ERROR { { { { {
iSM11704 ERROR { { { { {
iSM11705 ERROR { { { { {
iSM11706 ERROR { { { { {
iSM11707 ERROR { { { { {
iSM11708 ERROR { { { { {
iSM11709 ERROR { { { { {
iSM11710 WARNING { { { { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
650
Table A-1 Message Output Destination List (17/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM11711 WARNING { { {
iSM11712 WARNING { { {
iSM11713 WARNING { { {
iSM11714 WARNING { { {
iSM11721 ERROR { { { { { {
iSM11722 ERROR { { { { {
iSM11723 ERROR { { { { {
iSM11724 ERROR { { { { {
iSM11725 ERROR { { { { {
iSM11726 ERROR { { { { {
iSM11727 ERROR { { { { {
iSM11728 ERROR { { { { {
iSM11729 ERROR { { { { { {
iSM11730 ERROR { { { { {
iSM11731 ERROR { { { { {
iSM11732 ERROR { { { { {
iSM11733 ERROR { {
iSM11734 ERROR { {
iSM11735 ERROR { {
iSM11736 ERROR { {
iSM11737 ERROR { {
iSM11738 ERROR { {
iSM11739 ERROR { { {
iSM11740 ERROR { { {
iSM11742 ERROR { {
iSM11743 ERROR { {
iSM11744 ERROR { {
iSM11745 ERROR { {
iSM11746 ERROR { {
iSM11747 ERROR { {
iSM11748 ERROR { {
iSM11749 ERROR { {
iSM11750 ERROR { { { { { {
iSM11751 ERROR { { { { {
iSM11755 ERROR { { { { {
iSM11756 ERROR { { { { {
iSM11757 ERROR { { { { {
iSM11758 ERROR { { { { {
iSM11759 ERROR { {
iSM11760 ERROR { { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
651
Table A-1 Message Output Destination List (18/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM11781 ERROR { { { { { {
iSM11782 ERROR { { { { { {
iSM11783 ERROR { { { { { {
iSM11784 ERROR { { { { { {
iSM11785 ERROR { { { { { {
iSM11786 ERROR { { { { { {
iSM11787 ERROR { { { { { {
iSM11791 ERROR { { { { { {
iSM11792 ERROR { { { { { {
iSM11793 ERROR { { { { { {
iSM11794 ERROR { { { { { {
iSM11795 ERROR { { { { { {
iSM11796 ERROR { { { { { {
iSM11797 ERROR { { { { { {
iSM11799 ERROR { { { { { {
iSM11801 INFO {
iSM11802 INFO {
iSM11803 INFO {
iSM11804 INFO {
iSM13200 INFO { { { ∆
iSM13201 INFO { { { ∆ {
iSM13202 INFO { { { ∆ {
iSM13203 INFO { { { ∆ {
iSM13204 INFO { { { ∆ {
iSM13205 INFO { { { ∆ {
iSM13206 INFO { { { ∆ {
iSM13207 INFO { { { ∆ {
iSM13208 INFO { { { ∆ {
iSM13209 INFO { { { ∆ {
iSM13210 INFO { { { ∆ {
ISM13211 INFO { { { ∆ {
iSM13212 INFO { { { ∆ {
iSM13213 INFO { { { ∆ {
iSM13214 INFO { { { ∆ { {
iSM13215 INFO { { { ∆ { {
iSM13216 INFO { { { ∆ { {
iSM13218 INFO { {
iSM13219 INFO { {
iSM13220 INFO { { ∆ { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
652
Table A-1 Message Output Destination List (19/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM13221 INFO { { ∆ { {
iSM13222 INFO {
{ {
iSM13223 INFO {
{ {
iSM13224 INFO { { { ∆ { {
iSM13225 INFO { {
iSM13226 INFO { {
iSM13227 INFO { {
iSM13228 INFO { {
iSM13229 INFO { {
iSM13230 INFO {
{ {
iSM13231 INFO {
{ {
iSM13232 INFO {
{ {
iSM13233 INFO {
{ {
iSM13234 INFO {
{ {
iSM13235 INFO {
{ {
iSM13238 INFO { ∆ {
iSM13239 INFO { ∆ {
iSM13240 INFO { {
iSM13241 INFO { {
iSM13242 INFO { {
iSM13243 INFO { {
iSM13244 INFO { {
iSM13245 INFO { {
iSM13247 INFO { { { {
iSM13248 INFO { { { ∆ {
iSM13250 INFO {
{ {
iSM13251 INFO { {
iSM13252 INFO { {
iSM13253 INFO { {
iSM13254 INFO { {
iSM13255 INFO { {
iSM13256 INFO { {
iSM13400 WARNING { { { { { {
iSM13401 WARNING { { { { { {
iSM13403 WARNING { { { { { {
iSM13405 WARNING { { { { { {
iSM13406 WARNING { { { { { {
iSM13407 WARNING { {
iSM13408 WARNING { { { { { {
iSM13409 WARNING { { { { { {
iSM13410 WARNING { { { { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
653
Table A-1 Message Output Destination List (20/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM13411 WARNING { { { { { {
iSM13412 WARNING { { { { { {
iSM13413 WARNING { { { { { {
iSM13414 WARNING { { { { { {
iSM13415 WARNING { { { { { {
iSM13480 WARNING { { { { { {
iSM13481 WARNING { { { { { {
iSM13482 WARNING { { { { { {
iSM13483 WARNING { { { { { {
iSM13500 ERROR { { { { { {
iSM13501 ERROR { { { { { {
iSM13502 ERROR { { { { { {
iSM13503 ERROR { { { { { {
iSM13504 ERROR { { { { { {
iSM13505 ERROR { { { { { {
iSM13506 ERROR { { { { { {
iSM13507 ERROR { { { { { {
iSM13508 ERROR { { { { { {
iSM13509 ERROR { { { { { {
iSM13510 ERROR { { { { { {
iSM13511 ERROR { { { { { {
iSM13512 ERROR { { { { { {
iSM13513 ERROR { { { { { {
iSM13514 ERROR { { { { { {
iSM13515 ERROR { { { { { {
iSM13516 ERROR { { { { { {
iSM13517 ERROR { { { { { {
iSM13518 ERROR { { { { { {
iSM13519 ERROR { { { { { {
iSM13520 ERROR { { { { { {
iSM13521 ERROR { { { {
iSM13522 ERROR { { { {
iSM13523 ERROR { { { { { {
iSM13524 ERROR { { { { { {
iSM13525 ERROR { { { { { {
iSM13526 ERROR { { { { { {
iSM13527 ERROR { { { { { {
iSM13528 ERROR { { { { { {
iSM13529 ERROR { { { { { {
iSM13530 ERROR { { { { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
654
Table A-1 Message Output Destination List (21/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM13531 ERROR { { { { { {
iSM13532 ERROR { { { { { {
iSM13533 ERROR { { { { { {
iSM13535 ERROR { { { { { {
iSM13536 ERROR { { { { { {
iSM13537 ERROR { { { { { {
iSM13538 ERROR { { { { { {
iSM13539 ERROR { { { { { {
iSM13540 ERROR { { { { { {
iSM13541 ERROR { { { { { {
iSM13542 ERROR { { { { { {
iSM13543 ERROR { { { { { {
iSM13544 ERROR { { { { { {
iSM13545 ERROR { { { { { {
iSM13547 ERROR { { { { { {
iSM13548 ERROR { { { { { {
iSM13549 ERROR { { { { { {
iSM13550 ERROR { { { { { {
iSM13551 ERROR { { { { { {
iSM13552 ERROR { { { { { {
iSM13553 ERROR { { { { { {
iSM13554 ERROR { { { { { {
iSM13555 ERROR { { { { { {
iSM13556 ERROR { { { { { {
iSM13557 ERROR { { { { { {
iSM13558 ERROR { { { { { {
iSM13559 ERROR { { { { { {
iSM13560 ERROR { { { { { {
iSM13561 ERROR { { { { { {
iSM13562 ERROR { { { { { {
iSM13563 ERROR { { { { { {
iSM13564 ERROR { { { { { {
iSM13565 ERROR { { { { { {
iSM13566 ERROR { { { { { {
iSM13567 ERROR { { { { { {
iSM13568 ERROR { { { { { {
iSM13569 ERROR { { { { { {
iSM13570 ERROR { { { { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
655
Table A-1 Message Output Destination List (22/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM13571 ERROR { { { { { {
iSM13572 ERROR { { { { { {
iSM13573 ERROR { { { { { {
iSM13574 ERROR { { {
iSM13575 ERROR { { { { { {
iSM13576 ERROR { { { { { {
iSM13577 ERROR { { { { { {
iSM13578 ERROR { { { { { {
iSM13579 ERROR { { { { { {
iSM13580 ERROR { { { { { {
iSM13581 ERROR { { { { { {
iSM13582 ERROR { { { { { {
iSM13583 ERROR { { { { { {
iSM13584 ERROR { { { { { {
iSM13585 ERROR { { { { { {
iSM13586 ERROR { { { { { {
iSM13587 ERROR { { { { { {
iSM13588 ERROR { { { { { {
iSM13589 ERROR { { { { { {
iSM13590 ERROR { { { { { {
iSM13591 ERROR { { { { { {
iSM13592 ERROR { { { { { {
iSM13593 ERROR { { { { { {
iSM13594 ERROR { { { { { {
iSM13595 ERROR { { { { { {
iSM13596 ERROR { { { { { {
iSM13597 ERROR { { { { { {
iSM13598 ERROR { { { { { {
iSM13599 ERROR { { { { { {
iSM13600 ERROR { { { { { {
iSM13601 ERROR { { { { { {
iSM13602 ERROR {
iSM13603 ERROR {
iSM13604 ERROR {
iSM13605 ERROR {
iSM13606 ERROR { { {
iSM13607 ERROR { { {
iSM13608 ERROR {
iSM13609 ERROR { { {
iSM13610 ERROR { { { { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
656
Table A-1 Message Output Destination List (23/39)
Output destination
ID Operation log Syslog Event log Console ESMPRO link
Classification
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM13611 ERROR { { { { { {
iSM13612 ERROR { { { { { {
iSM13613 ERROR { { {
iSM13614 ERROR { { { { { {
iSM13615 ERROR { { {
iSM13616 ERROR { { { { { {
iSM13617 ERROR { { { { { {
iSM13618 ERROR { { {
iSM13619 ERROR { { {
iSM13623 ERROR { { {
iSM13624 ERROR { { {
iSM13625 ERROR { { {
iSM13626 ERROR { { {
iSM13627 ERROR { { {
iSM13629 ERROR { { {
iSM13630 ERROR {
iSM13631 ERROR {
iSM13632 ERROR {
iSM13633 ERROR { { {
iSM13634 ERROR { { {
iSM13635 ERROR { { {
iSM13636 ERROR { { {
iSM13637 ERROR { { {
iSM13638 ERROR { { { { { {
iSM13639 ERROR { { {
iSM13640 ERROR { { { { { {
iSM13641 ERROR { { { { { {
iSM13642 ERROR { { { {
iSM13644 ERROR { { {
iSM13645 ERROR { { { { { {
iSM13646 ERROR { { { {
iSM13647 ERROR { { { { { {
iSM13648 ERROR { { { { { {
iSM13649 ERROR { { { { { {
iSM13650 ERROR { { { { { {
iSM13651 ERROR { { { { { {
iSM13652 ERROR { { { { { {
iSM13653 ERROR { { { { { {
iSM13654 ERROR { { { { { {
iSM13655 ERROR { { { { { {
iSM13656 ERROR { { { { { {
iSM13657 ERROR { { { { { {
iSM13658 ERROR { { { { { {
iSM13659 ERROR { { { { { {
iSM13660 ERROR { { { { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
657
Table A-1 Message Output Destination List (24/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM13661 ERROR { { { { { {
iSM13662 ERROR { { { { { {
iSM13663 ERROR { { { { { {
iSM13664 ERROR { { { { { {
iSM13669 ERROR { { {
iSM13670 ERROR { { { { { {
iSM13671 ERROR { { { { { {
iSM13672 ERROR { { { { { {
iSM13673 ERROR { { { { { {
iSM13674 ERROR { { { { { {
iSM13675 ERROR { { { {
iSM13676 ERROR { { { {
iSM13677 ERROR { { {
iSM13678 ERROR { { {
iSM13679 ERROR { { {
iSM13680 ERROR { { {
iSM13681 ERROR { { {
iSM13682 ERROR { { {
iSM13683 ERROR { { {
iSM13684 ERROR { { {
iSM13685 ERROR { { {
iSM13686 ERROR { { {
iSM13687 ERROR { { {
iSM13688 ERROR { { {
iSM13689 ERROR { { {
iSM13690 ERROR { { {
iSM13691 ERROR { { {
iSM13692 ERROR { { {
iSM13693 ERROR { { {
iSM13694 ERROR { { {
iSM13695 ERROR { { {
iSM13696 ERROR { { {
iSM13697 ERROR { { {
iSM13698 ERROR { { {
iSM13699 ERROR { { {
iSM13700 ERROR { { { { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
658
Table A-1 Message Output Destination List (25/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM13701 ERROR { { { { { {
iSM13702 ERROR { { { { { {
iSM13703 ERROR { { { { { {
iSM13704 ERROR { { { { { {
iSM13705 ERROR { { { { { {
iSM13706 ERROR { { { { { {
iSM13707 ERROR { { { { { {
iSM13708 ERROR { { { { { {
iSM13709 ERROR { { { { { {
iSM13710 ERROR { { { { { {
iSM13711 ERROR { { { { { {
iSM13712 ERROR { { { { { {
iSM13713 ERROR { { { { { {
iSM13714 ERROR { { { { { {
iSM13715 ERROR { { { { { {
iSM13716 ERROR { { { { { {
iSM13717 ERROR { { { { { {
iSM13718 ERROR { { { { { {
iSM13719 ERROR { { { { { {
iSM13720 ERROR { { { { { {
iSM13721 ERROR { { { { { {
iSM13722 ERROR { { { { { {
iSM13723 ERROR { { { { { {
iSM13724 ERROR { { { { { {
iSM13725 ERROR { { { { { {
iSM13726 ERROR { { { { { {
iSM13727 ERROR { { { { { {
iSM13728 ERROR { { { { { {
iSM13729 ERROR { { { { { {
iSM13730 ERROR { { { { { {
iSM13731 ERROR { { { { { {
iSM13732 ERROR { { { { { {
iSM13734 ERROR { { { { { {
iSM13735 ERROR { { { { { {
iSM13736 ERROR { { { {
iSM13737 ERROR { { { {
iSM13738 ERROR { { { {
iSM13739 ERROR { { { {
iSM13740 ERROR { { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
659
Table A-1 Message Output Destination List (26/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM13741 ERROR { { { { { {
iSM13742 ERROR { { { { { {
iSM13743 ERROR { { { { { {
iSM13744 ERROR { { { { { {
iSM13745 ERROR { { { { { {
iSM13746 ERROR { { { { { {
iSM13747 ERROR { { { { { {
iSM13748 ERROR { { { { { {
iSM13749 ERROR { { { { { {
iSM13750 ERROR { { { { { {
iSM13751 ERROR { { { { { {
iSM13752 ERROR { { { { { {
iSM13753 ERROR { { { { { {
iSM13754 ERROR { { { { { {
iSM13755 ERROR { { { { { {
iSM13761 ERROR { { {
iSM13762 ERROR { { {
iSM13763 ERROR { { {
iSM13764 ERROR { { {
iSM13765 ERROR { { {
iSM13766 ERROR { { {
iSM13767 ERROR { { {
iSM13768 ERROR { { {
iSM13769 ERROR { { {
iSM13770 ERROR { { {
iSM13771 ERROR { { {
iSM13772 ERROR { { {
iSM13773 ERROR { { {
iSM13774 ERROR { { {
iSM13775 ERROR { { {
iSM13776 ERROR { { {
iSM13777 ERROR { { {
iSM13778 ERROR { { {
iSM13779 ERROR { { {
iSM13780 ERROR { { {
iSM13800 ERROR { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
660
Table A-1 Message Output Destination List (27/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM13801 ERROR { { {
iSM13802 ERROR { { {
iSM13803 ERROR { { {
iSM13804 ERROR { { {
iSM13805 ERROR { { {
iSM13806 ERROR { { {
iSM13807 ERROR { { {
iSM13808 ERROR { { {
iSM13809 ERROR { { {
iSM13810 ERROR { { {
iSM13811 ERROR { { {
iSM13812 ERROR { { {
iSM13813 ERROR { { {
iSM13814 ERROR { { {
iSM13815 ERROR { { {
iSM13816 ERROR { { {
iSM13817 ERROR { { {
iSM13818 ERROR { { {
iSM13819 ERROR { { {
iSM13820 ERROR { { {
iSM13821 ERROR { { {
iSM13822 ERROR { { {
iSM13823 ERROR { { {
iSM13824 ERROR { { {
iSM13825 ERROR { { {
iSM13826 ERROR { { {
iSM13827 ERROR { { {
iSM13828 ERROR { { {
iSM13829 ERROR { { {
iSM13830 ERROR { { {
iSM13831 ERROR { { {
iSM13832 ERROR { { {
iSM13833 ERROR { { {
iSM13834 ERROR { { {
iSM13835 ERROR { { {
iSM13836 ERROR { { {
iSM14400 INFO { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
661
Table A-1 Message Output Destination List (28/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM14401 INFO { {
iSM14402 INFO { {
iSM14403 INFO { {
iSM14404 INFO { {
iSM14405 INFO { {
iSM14406 INFO { {
iSM14407 INFO { {
iSM14408 INFO { {
iSM14409 INFO { {
iSM14410 INFO { {
iSM14411 INFO { {
iSM14412 INFO { {
iSM14413 INFO { {
iSM14414 INFO { {
iSM14415 INFO { {
iSM14416 INFO { {
iSM14417 INFO { {
iSM14418 INFO { {
iSM14419 INFO { {
iSM14420 INFO { {
iSM14421 INFO { {
iSM14422 INFO { {
iSM14423 INFO { {
iSM14424 INFO { {
iSM14425 INFO { {
iSM14426 INFO { {
iSM14427 INFO { {
iSM14428 INFO { {
iSM14429 INFO { {
iSM14430 INFO { {
iSM14431 INFO { {
iSM14432 INFO { {
iSM14433 INFO { {
iSM14434 INFO { {
iSM14435 INFO { {
iSM14436 INFO { {
iSM14437 INFO { {
iSM14438 INFO { {
iSM14439 INFO { {
iSM14440 INFO { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
662
Table A-1 Message Output Destination List (29/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM14441 INFO { {
iSM14442 INFO { {
iSM14443 INFO { {
iSM14444 INFO { {
iSM14445 INFO { {
iSM14446 INFO { {
iSM14447 INFO { {
iSM14448 INFO { {
iSM14449 INFO { {
iSM14450 INFO { {
iSM14451 INFO { {
iSM14452 INFO { {
iSM14453 INFO { {
iSM14454 INFO { {
iSM14456 INFO { {
iSM14457 INFO { {
iSM14458 INFO { {
iSM14459 INFO { {
iSM14461 INFO { {
iSM14462 INFO { {
iSM14464 INFO { {
iSM14467 INFO { {
iSM14468 INFO { {
iSM14469 INFO { {
iSM14470 INFO { {
iSM14471 INFO { {
iSM14472 INFO { {
iSM14474 INFO { {
iSM14475 INFO { {
iSM14476 INFO { {
iSM14600 INFO { {
iSM14601 INFO { {
iSM15600 INFO { {
iSM16001 INFO { {
iSM16020 NOTICE { { { {
iSM16021 NOTICE { { { {
iSM16029 WARNING { { { {
iSM16030 WARNING { { { {
iSM16031 WARNING { { { {
iSM16032 WARNING { { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
663
Table A-1 Message Output Destination List (30/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM16033 WARNING { { { {
iSM16034 WARNING { { { {
iSM16035 WARNING { { { {
iSM16037 WARNING { { { {
iSM16038 WARNING { { { {
iSM16039 WARNING { { { {
iSM16041 WARNING { { { {
iSM16043 WARNING { { { {
iSM16044 WARNING { { { {
iSM16045 WARNING { { { {
iSM16047 WARNING { { { {
iSM16048 WARNING { { { {
iSM16049 WARNING { { { {
iSM16061 WARNING { { { {
iSM16062 WARNING { { { {
iSM16063 WARNING { { { {
iSM16064 WARNING { { { {
iSM16065 WARNING { { { {
iSM16066 WARNING { { { {
iSM16070 WARNING { { { {
iSM16071 WARNING { { { {
iSM16080 INFO { { { ∆
iSM16081 WARNING { { { {
iSM16082 WARNING { { { {
iSM16083 ERROR { { { {
iSM16084 ERROR { { { {
iSM17001 NOTICE { { { {
iSM17002 NOTICE { { { {
iSM17003 NOTICE { { { {
iSM17004 NOTICE { { { {
iSM17010 NOTICE { { { {
iSM17020 WARNING { { { {
iSM17030 WARNING { { { {
iSM17040 WARNING { { { {
iSM17050 WARNING { { { {
iSM17900 WARNING {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
664
Table A-1 Message Output Destination List (31/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM18001 INFO { { { ∆
iSM18002 INFO { { { ∆
iSM18003 INFO { { { ∆
iSM18004 INFO { { { ∆
iSM18005 INFO { { { ∆
iSM18006 INFO { { { ∆
iSM18007 ERROR { { { { {
{
iSM18008 NOTICE { { { {
iSM18201 WARNING { { { {
iSM18202 WARNING { { { {
iSM18203 WARNING { { { {
iSM18204 WARNING { { { {
iSM18205 WARNING { { { {
iSM18301 ERROR { { { {
iSM18302 ERROR { { { {
iSM18303 WARNING { { { {
iSM18311 ERROR { { { {
iSM18321 WARNING { { { {
iSM18501 INFO { { { ∆
iSM18502 INFO { { { ∆
iSM18503 INFO { { { ∆
iSM18601 WARNING { { { {
iSM18602 WARNING { { { {
iSM18603 WARNING { { { {
iSM18999 WARNING { { { {
iSM19000 INFO { { { ∆ {
iSM19010 INFO
{
iSM19011 INFO { { { ∆ {
iSM19012 INFO { { { ∆ { {
iSM19013 INFO { { { ∆ {
iSM19020 INFO
{
iSM19021 INFO { { { ∆ {
iSM19022 INFO { { { ∆ { {
iSM19023 INFO { { { ∆ {
iSM19030 INFO
{
iSM19031 INFO { { { ∆ {
iSM19032 INFO { { { ∆ { {
iSM19033 INFO { { { ∆ {
iSM19034 INFO { { { ∆ { {
iSM19035 INFO { { { ∆ {
iSM19100 ERROR { { { { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
665
Table A-1 Message Output Destination List (32/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM19101 ERROR { { { { { {
iSM19102 ERROR { { { { { {
iSM19103 ERROR { { { { { {
iSM19104 ERROR { { { { { {
iSM19105 ERROR { { { { { {
iSM19106 ERROR { { { { { {
iSM19107 ERROR { { { { { {
iSM19108 ERROR { { { { { {
iSM19109 ERROR { { { { { {
iSM19110 ERROR { { { { { {
iSM19111 ERROR { { { { { {
iSM19112 ERROR { { { { { {
iSM19113 ERROR { { { { { {
iSM19114 ERROR { { { { { {
iSM19115 ERROR { { { { { {
iSM19116 ERROR { { {
iSM19117 ERROR { { {
iSM19118 ERROR { { { { { {
iSM19119 ERROR { { { { { {
iSM19120 ERROR { { {
iSM19121 ERROR { { { { { {
iSM19122 ERROR { { { { { {
iSM19123 ERROR { { { { { {
iSM19124 INFO { { { ∆ { {
iSM19125 INFO { { { ∆ { {
iSM19126 INFO { { { ∆ { {
iSM19127 INFO { { { ∆ { {
iSM19200 ERROR { { { { { {
iSM19202 ERROR { { { { { {
iSM19203 ERROR { { { {
iSM19208 ERROR { { { { { {
iSM19209 ERROR { { { { { {
iSM19210 ERROR { { { { { {
iSM19212 WARNING { { { ∆ { {
iSM19213 ERROR { { { { { {
iSM19301 ERROR { { { { { {
iSM19302 ERROR { { { { { {
iSM19303 ERROR { { { { { {
iSM19304 ERROR { { { { { {
iSM19305 ERROR { { { { { {
iSM19306 ERROR { { { { { {
iSM19307 ERROR { { { { { {
iSM19308 ERROR { { { { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
666
Table A-1 Message Output Destination List (33/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM19401 ERROR { { { { { {
iSM19402 ERROR { { { { { {
iSM19403 ERROR { { {
iSM19404 ERROR { { {
iSM19405 ERROR { { { { { {
iSM19408 INFO { { { ∆ {
iSM20000 INFO { { { ∆ {
iSM20010 INFO {
iSM20011 INFO { { { ∆ {
iSM20012 INFO { { { ∆ { {
iSM20013 INFO { { { ∆ {
iSM20020 INFO {
iSM20021 INFO { { { ∆ {
iSM20022 INFO { { { ∆ { {
iSM20023 INFO { { { ∆ {
iSM20030 INFO {
iSM20031 INFO { { { ∆ {
iSM20032 INFO { { { ∆ { {
iSM20033 INFO { { { ∆ {
iSM20100 ERROR { { { { { {
iSM20101 ERROR { { { { { {
iSM20102 ERROR { { { { { {
iSM20103 ERROR { { { { { {
iSM20104 ERROR { { { { { {
iSM20106 ERROR { { { { { {
iSM20107 ERROR { { { { { {
iSM20108 ERROR { { { { { {
iSM20109 ERROR { { { { { {
iSM20112 ERROR { { { { { {
iSM20116 ERROR { { { { { {
iSM20117 ERROR { { { { { {
iSM20118 ERROR { { { { { {
iSM20119 ERROR { { { { { {
iSM20120 ERROR { { { { { {
iSM20121 ERROR { { { { { {
iSM20122 ERROR { { { { { {
iSM20123 ERROR { { { { { {
iSM20200 ERROR { { { { { {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
667
Table A-1 Message Output Destination List (34/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSM20201 ERROR { { { { { {
iSM20202 ERROR { { { { { {
iSM20203 ERROR { {
{
iSM20204 ERROR { { { {
iSM20205 WARNING { { { ∆ { {
iSM20206 ERROR { { { { { {
iSM20207 ERROR { { { { { {
iSM20208 ERROR { { { { { {
iSM20209 ERROR { { { { { {
iSM20210 ERROR { { { { { {
iSM20211 ERROR { { { { { {
iSM20301 ERROR { { { { { {
iSM20302 ERROR { { { { { {
iSM20303 ERROR { { { { { {
iSM20304 ERROR { { { { { {
iSM20305 ERROR { { { { { {
iSM20306 ERROR { { { { { {
iSM20307 ERROR { { { { { {
iSM20308 ERROR { { { { { {
iSM20401 ERROR { { { { { {
iSM20402 ERROR { { { { { {
iSM20403 ERROR { { { { { {
iSM20404 WARNING { { { ∆ { {
iSM20405 ERROR { { { { { {
iSM20406 ERROR { { { { { {
iSM99001 INFO {
iSM99002 INFO {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
668
Table A-1 Message Output Destination List (35/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSMnetconf:
001
INFO {
iSMnetconf
:101
INFO {
iSMnetconf:
111
INFO {
iSMnetconf:
112
INFO {
iSMnetconf:
201
INFO {
iSMnetconf:
202
INFO {
iSMnetconf:
203
INFO {
iSMnetconf:
211
INFO {
iSMnetconf:
212
INFO {
iSMnetconf:
221
INFO {
iSMnetconf:
222
INFO {
iSMnetconf:
223
INFO {
iSMnetconf:
224
INFO {
iSMnetconf:
225
INFO {
iSMnetconf:
226
INFO {
iSMnetconf:
227
INFO {
iSMnetconf:
228
INFO {
iSMnetconf:
229
INFO {
iSMnetconf:
230
INFO {
iSMnetconf:
241
INFO {
iSMnetconf:
242
INFO {
iSMprfarc:
101
- {
iSMprfarc:
102
- {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
669
Table A-1 Message Output Destination List (36/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSMprfarc:
103
- {
iSMprfarc:
104
- {
iSMprfarc:
105
- {
iSMprfarc:
106
- {
iSMprfarc:
107
- {
iSMprfarc:
108
- {
iSMprfarc:
109
- {
iSMprfarc:
110
- {
iSMprfarc:
111
- {
iSMprfarc:
112
- {
iSMprfarc:
120
- {
iSMprfarc:
201
- {
iSMprfctl
001
- {
iSMprfctl
010
- {
iSMprfctl
011
- {
iSMprfctl
012
- {
iSMprfctl
013
- {
iSMprfctl
020
- {
iSMprfctl
021
- {
iSMprfctl
022
- {
iSMprfctl
023
- {
iSMprfctl
030
- {
iSMprfctl
031
- {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
670
Table A-1 Message Output Destination List (37/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSMprfctl
032
- {
iSMprfctl
033
- {
iSMprfctl
035
- {
iSMprfctl
036
- {
iSMprfctl
037
- {
iSMprfctl
040
- {
iSMprfctl
041
- {
iSMprfctl
042
- {
iSMprfctl
043
- {
iSMprfctl
044
- {
iSMprfctl
050
- {
iSMprfctl
051
- {
iSMprfctl
060
- {
iSMprfctl
090
- {
iSMprfctl
910
- {
iSMprfedit:
001
- {
iSMprfedit:
100
- {
iSMprfedit:
101
- {
iSMprfedit:
102
- {
iSMprfedit:
103
- {
iSMprfedit:
110
- {
iSMprfedit:
111
- {
iSMprfedit:
112
- {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
671
Table A-1 Message Output Destination List (38/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSMprfedit:
113
- {
iSMprfedit:
114
- {
iSMprfedit:
115
- {
iSMprfedit:
120
- {
iSMprfedit:
121
- {
iSMprfedit:
122
- {
iSMprfedit:
999
- {
iSMprfext:
001
- {
iSMprfext:
002
- {
iSMprfext:
003
- {
iSMprfext:
004
- {
iSMprfext:
005
- {
iSMprfext:
006
- {
iSMprfext:
007
- {
iSMprfext:
008
- {
iSMprfext:
009
- {
iSMprfext:
010
- {
iSMprfext:
011
- {
iSMprflog:
001
- {
iSMprflog:
002
- {
iSMprflog:
003
- {
iSMprflog:
010
- {
iSMprflog:
011
- {
{: Output ∆: Not output when the default is selected
Appendix A Message Output Destination List
672
Table A-1 Message Output Destination List (39/39)
Output destination
ID Classification Operation log Syslog Event log Console ESMPRO link
UNIX Windows HP-UX Solaris Windows ALIVE/
express
report
Manager
iSMprflog:
100
- {
iSMprflog:
101
- {
iSMprflog:
102
- {
iSMprflog:
103
- {
iSMprflog:
104
- {
iSMprflog:
120
- {
iSMprflog:
121
- {
iSMprflog:
122
- {
iSMprflog:
123
- {
iSMprflog:
900
- {
{: Output ∆: Not output when the default is selected
Appendix B Changed Message List
673
Appendix B Changed Message List
Table B-1 Message modification list (1/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old
Illegal configuration. file=<aaa...a> line=<bbb...b>
[section=<ccc...c>] [keyword=<ddd...d>] [value=<eee...e>]
[token=<fff...f>] NOTICE
iSM01110 {
New
Illegal configuration. file=<aaa...a> line=<bbb...b>
[section=<ccc...c>] [keyword=<ddd...d>] [value=<eee...e>]
[token=<fff...f>] [detail=<ggg...g>] NOTICE
Old
Data can not be received sequentially during split
mode.ip=<aaa...a> port=<bbbbb> reason=(invalid sequence)
detail=<cc-dddd> ERROR
iSM03206 {
New - -
Old
Control path is blockaded. file=(<aaa...a>) func=<bbb...b>
errno=<ccccc> status=<ddd...d> (<eee...e> productID=<fffff>
SN=<ggggg>) [UC=<hhhhhhhh> FC=<ii>] ERROR
iSM03224 {
New
Control path is blockaded. file=(<aaa...a>) func=<bbb...b>
errno=<ccccc> status=<ddd...d> (<eee...e> productID=<fffff>
SN=<ggggg>) [UC=<hhhhhhhh> FC=<ii>][_ALERT_] ERROR
Old
Control path is blockaded. disk=(disk<aaa> (Port<bbb>
Bus<ccc> Target<ddd> Lun<eee>)) func=<fff...f>
errno=<ggggg> status=<hhh...h> (<iii...i> productID=<jjjjj>
SN=<kkkkk>) [UC=<llllllll> FC=<mm>]
ERROR
iSM03224 {
New
Control path is blockaded. disk=(disk<aaa> (Port<bbb>
Bus<ccc> Target<ddd> Lun<eee>)) func=<fff...f>
errno=<ggggg> status=<hhh...h> (<iii...i> productID=<jjjjj>
SN=<kkkkk>) [UC=<llllllll> FC=<mm>][_ALERT_]
ERROR
Old
Control path is blockaded. ip=(<aaa...a>) func=<bbb...b>
errno=<ccccc> status=<ddddd> (<eee...e> productID=<fffff>
SN=<ggggg>) [UC=<hhhhhhhh> FC=<ii>] ERROR
iSM03224 {
New
Control path is blockaded. ip=(<aaa...a>) func=<bbb...b>
errno=<ccccc> status=<ddddd> (<eee...e> productID=<fffff>
SN=<ggggg>) [UC=<hhhhhhhh> FC=<ii>][_ALERT_] ERROR
Old
All control paths of (<aaa...a> productID=<bbbbb>
SN=<ccccc>) are not available. detail=<dd-eeee> ERROR
iSM03226 {
New - -
Old
Received invalid socket event. event=(<aaaaaaaa>)
pid=<bbbbbb> detail=<cc-dddd> ERROR
iSM03412 {
New - -
Appendix B Changed Message List
674
Table B-1 Message modification list (2/32)
Modification Modification
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old Resource monitoring started. (<aaa...a> productID=<bbbbb>
SN=<ccccc>) [UC=<dddddddddd> FC=<ee>] INFO
iSM07012
{
New
Resource monitoring started. (<aaa...a> productID=<bbbbb>
SN=<ccccc>) [UC=<dddddddddd> FC=<ee>][_ALERT_] INFO
Old
Resource monitoring stopped by control path fault. (<aaa...a>
productID=<bbbbb> SN=<ccccc>) [UC=<dddddddddd>
FC=<ee>] ERROR
iSM07023 {
New
Resource monitoring stopped by control path fault. (<aaa...a>
productID=<bbbbb> SN=<ccccc>) [UC=<dddddddddd>
FC=<ee>] [_ALERT_] ERROR
Old
Resource monitoring stopped by information collecting
failure. (<aaa...a> productID=<bbbbb> SN=<ccccc>)
[UC=<dddddddddd> FC=<ee>] ERROR
iSM07024 {
New
Resource monitoring stopped by information collecting
failure. (<aaa...a> productID=<bbbbb> SN=<ccccc>)
[UC=<dddddddddd> FC=<ee>] [_ALERT_] ERROR
Old
Resource monitoring changes to recovery mode.(<aaa...a>
productID=<bbbbb> SN=<ccccc>) [UC=<dddddddddd>
FC=<ee>] ERROR
iSM07026 {
New
Resource monitoring changes to recovery mode.(<aaa...a>
productID=<bbbbb> SN=<ccccc>) [UC=<dddddddddd>
FC=<ee>] [_ALERT_] ERROR
Old Collecting information failed. (<aaa…a>) WARNING
ISM07092 {
New - -
Old
State of PD(<aa>h) has become fault. (<bbb...b>
productID=<ccc...c> SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>) ERROR
iSM07102 {
New
State of PD(<aa>h) has become fault. (<bbb...b>
productID=<ccc...c> SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>)[_ALERT_] ERROR
Old
State of PD(<aa>h) has become attn(rebuilding). (<bbb...b>
productID=<ccc...c> SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>) ERROR
iSM07104 {
New
State of PD(<aa>h) has become attn(rebuilding). (<bbb...b>
productID=<ccc...c> SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>)[_ALERT_] ERROR
Old
State of PD(<aa>h) has become ready. (<bbb...b>
productID=<ccc...c> SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>) INFO
iSM07109 {
New
State of PD(<aa>h) has become ready. (<bbb...b>
productID=<ccc...c> SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>)[_ALERT_] INFO
Appendix B Changed Message List
675
Table B-1 Message modification list (3/32)
Modification Modification
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old
State of <aaaaa>(<bb>h[-<cc>h]) has become fault.
(<ddd...d> productID=<eeeee> SN=<fffff> No=<gg>h ) ERROR
iSM07112 {
New
State of <aaaaa>(<bb>h[-<cc>h]) has become fault.
(<ddd...d> productID=<eeeee> SN=<fffff>
No=<gg>h )[_ALERT_] ERROR
Old
State of LD has become fault(media error). (<aaa...a>
productID=<bbb...b> SN=<ccc...c> No=<dddd>h
Name=<eee...e> [PDN=<ff>h-<gg>h])) ERROR
iSM07123 {
New
State of LD has become fault(media error). (<aaa...a>
productID=<bbb...b> SN=<ccc...c> No=<dddd>h
Name=<eee...e> [PDN=<ff>h-<gg>h]))[_ALERT_] ERROR
Old
State of RANK has become fault. (<aaa...a>
productID=<bbbbb> SN=<ccccc> No=<dd>h-<ee>h ) ERROR
iSM07142 {
New
State of RANK has become fault. (<aaa...a>
productID=<bbbbb> SN=<ccccc> No=<dd>h-<ee>h )
[_ALERT_] ERROR
Old
State of PD(<aa>h) has become fault. (<bbb...b>
productID=<ccc...c> SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>) [UC=<hhh...h> FC=<ii>] ERROR
iSM07152 {
New
State of PD(<aa>h) has become fault. (<bbb...b>
productID=<ccc...c> SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>) [UC=<hhh...h> FC=<ii>][_ALERT_] ERROR
Old
State of PD(<aa>h) has become attn(rebuilding).
(<bbb...b> productID=<ccc...c> SN=<ddd...d>
No=<ee>h-<ff>h <ggg...g>) [UC=<hhh...h> FC=<ii>] NOTICE
iSM07154 {
New
State of PD(<aa>h) has become attn(rebuilding).
(<bbb...b> productID=<ccc...c> SN=<ddd...d>
No=<ee>h-<ff>h <ggg...g>) [UC=<hhh...h> FC=<ii>]
[_ALERT_]
NOTICE
Old
State of PD(<aa>h) has become ready. (<bbb...b>
productID=<ccc...c> SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>) [UC=<hhh...h> FC=<ii>] INFO
iSM07159 {
New
State of PD(<aa>h) has become ready. (<bbb...b>
productID=<ccc...c> SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>) [UC=<hhh...h> FC=<ii>][_ALERT_] INFO
Old
State of <aaaaa>(<bb>h[-<cc>h]) has become fault.
(<ddd...d> productID=<eeeee> SN=<fffff> No=<gg>h)
[UC=<hhhhhhhhhh> FC=<ii>] ERROR
iSM07162 {
New
State of <aaaaa>(<bb>h[-<cc>h]) has become fault.
(<ddd...d> productID=<eeeee> SN=<fffff> No=<gg>h)
[UC=<hhhhhhhhhh> FC=<ii>] [_ALERT_] ERROR
Appendix B Changed Message List
676
Table B-1 Message modification list (4/32)
Modification Modification
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old
State of LD has become fault(media error). (<aaa...a>
productID=<bbb...b> SN=<ccc...c> No=<dddd>h
Name=<eee...e> [PDN=<ff>h-<gg>h]) [UC=<hhh...h>
FC=<ii>]
ERROR
iSM07173 {
New
State of LD has become fault(media error). (<aaa...a>
productID=<bbb...b> SN=<ccc...c> No=<dddd>h
Name=<eee...e> [PDN=<ff>h -<gg>h]) [UC=<hhh...h>
FC=<ii>][_ALERT_]
ERROR
Old
State of RANK has become fault. (<aaa...a>
productID=<bbbbb> SN=<ccccc> No=<dd>h-<ee>h)
[UC=<ffffffffff> FC=<gg>] ERROR
iSM07192 {
New
State of RANK has become fault. (<aaa...a>
productID=<bbbbb> SN=<ccccc> No=<dd>h-<ee>h)
[UC=<ffffffffff> FC=<gg>] [_ALERT_] ERROR
Old CHE-Disk has configured. (<aaa…a>) NOTICE
iSM07206 {
New - -
Old ACCESS_CONTROL has configured. (<aaa…a>) NOTICE
iSM07208 {
New - -
Old
State of PD(<aa>h) has become info(inactive). (<bbb...b>
productID=<ccc...c> SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>) INFO
iSM07402 {
New
State of PD(<aa>h) has become info(inactive). (<bbb...b>
productID=<ccc...c> SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>)[_ALERT_] INFO
Old
State of POOL has become fault. (<aaa...a>
productID=<bbb...b> SN=<ccc...c> No=<dddd>h
Name=<eee...e>) ERROR
iSM07412 {
New
State of POOL has become fault. (<aaa...a>
productID=<bbb...b> SN=<ccc...c> No=<dddd>h
Name=<eee...e>)[_ALERT_] ERROR
Old
State of PD(<aa>h) has become info(inactive). (<bbb...b>
productID=<ccc...c> SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>) [UC=<hhh...h> FC=<ii>] INFO
iSM07452 {
New
State of PD(<aa>h) has become info(inactive). (<bbb...b>
productID=<ccc...c> SN=<ddd...d> No=<ee>h-<ff>h
<ggg...g>) [UC=<hhh...h> FC=<ii>] [_ALERT_] INFO
Old
State of POOL has become fault. (<aaa...a>
productID=<bbb...b> SN=<ccc...c> No=<dddd>h
Name=<eee...e>) [UC=<fff...f> FC=<gg>] ERROR
iSM07462 {
New
State of POOL has become fault. (<aaa...a>
productID=<bbb...b> SN=<ccc...c> No=<dddd>h
Name=<eee...e>) [UC=<fff...f> FC=<gg>] [_ALERT_] ERROR
Appendix B Changed Message List
677
Table B-1 Message modification list (5/32)
Modification Modification
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old - -
iSM07616 {
New
The capacity of SRA used is over threshold.(<aaa...a>
productID=<bbb...b> SN=<ccc...c> No=<dddd>h
Name=<eee...e> capacity=<fff...f>GB
threshold=<ggg...g>GB)
WARNING
Old
-
-
iSM07617 {
New
The capacity of SRA used is under threshold.(<aaa...a>
productID=<bbb...b> SN=<ccc...c> No=<dddd>h
Name=<eee...e> capacity=<fff...f>GB
threshold=<ggg...g>GB)
INFO
Old
Expansion State of POOL has become normal-end. (<aaa...a>
productID=<bbb...b> SN=<ccc...c> No=<dddd>h
Name=<eee...e>) INFO
iSM07620 {
New
Expansion State of POOL has become normal-end. (<aaa...a>
productID=<bbb...b> SN=<ccc...c> No=<dddd>h
Name=<eee...e>)[_ALERT_] INFO
Old
Expansion State of POOL has become expanding. (<aaa...a>
productID=<bbb...b> SN=<ccc...c> No=<dddd>h
Name=<eee...e>) NOTICE
iSM07621 {
New
Expansion State of POOL has become expanding. (<aaa...a>
productID=<bbb...b> SN=<ccc...c> No=<dddd>h
Name=<eee...e>)[_ALERT_] NOTICE
Old
Expansion State of POOL has become expand-fail. (<aaa...a>
productID=<bbb...b> SN=<ccc...c> No=<dddd>h
Name=<eee...e>) ERROR
iSM07622 {
New
Expansion State of POOL has become expand-fail. (<aaa...a>
productID=<bbb...b> SN=<ccc...c> No=<dddd>h
Name=<eee...e>)[_ALERT_] ERROR
Old
Expansion State of POOL has become normal-end.
(<aaa...a> productID=<bbb...b> SN=<ccc...c> No=<dddd>h
Name=<eee...e>) INFO
iSM07670 {
New
Expansion State of POOL has become normal-end. (<aaa...a>
productID=<bbb...b> SN=<ccc...c> No=<dddd>h
Name=<eee...e>) [UC=<fff...f> FC=<gg>][_ALERT_] INFO
Old
Expansion State of POOL has become expanding. (<aaa...a>
productID=<bbb...b> SN=<ccc...c> No=<dddd>h
Name=<eee...e>) NOTICE
iSM07671 {
New
Expansion State of POOL has become expanding. (<aaa...a>
productID=<bbb...b> SN=<ccc...c> No=<dddd>h
Name=<eee...e>) [UC=<fff...f> FC=<gg>][_ALERT_] NOTICE
Appendix B Changed Message List
678
Table B-1 Message modification list (6/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old
Expansion State of POOL has become expand-fail.
(<aaa...a> productID=<bbb...b> SN=<ccc...c> No=<dddd>h
Name=<eee...e>) ERROR
iSM07672
{
New
Expansion State of POOL has become expand-fail.
(<aaa...a> productID=<bbb...b> SN=<ccc...c>
No=<dddd>h Name=<eee...e>) [UC=<fff...f>
FC=<gg>][_ALERT_]
ERROR
Old Illegal write data is detected. (<aaa...a>,
LDN=<bbbb>h, host-info=<ccc...c>) WARNING
iSM07950
{
New Illegal write data has been detected. (<aaa...a>,
LD=<bbb...b>(<cccc>h), host-info=<ddd...d>) WARNING
Old
Disk array=<aaa...a> logging is started(overload)
interval=<bb> INFO
iSM08035 {
New Disk array=<aaa...a> logging is started(overload)
interval=<bb> NOTICE
Old
Threshold excess state has been reset [Disk array=<aaa...a>]
[type=<bbbb>] [number=<cccc>] [<<dddddddd>>] NOTICE
iSM08054 {
New
Threshold excess state has been reset [Disk
array=<aaa...a>] [type=<bbbb>] [number=<cccc>]
[<<dddddddd>>]
NOTICE
Old command: <aaa...a>, <bbb...b>,
status=failed(<ccc...c>h/<ddd...d>h/<eee...e>h) INFO
iSM10302 {
New command: <aaa...a>, <bbb...b>,
status=failed(<cc>h/<dd>h/<ee>h) INFO
Old
Replication state of Logical Disk was changed:
LD=<aaa...a>(<bbb...b>h) <ccc...c>, Restriction=<ddd...d>[,
Shadow copy data=<eeeeeee>] [, several states changed.] NOTICE
iSM10318 {
New
Replication state of Logical Disk was changed:
LD=<aaa...a>(<bbbb>h) <ccc...c>, Restriction=<ddd...d> [,
several states changed.] NOTICE
Appendix B Changed Message List
679
Table B-1 Message modification list (7/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old copy error:mv=<aaa...a> (<bbb...b>h) <ccc...c>,
rv=<aaa...a> (<bbb...b>h)<ccc...c>, status=<ddd...d>h NOTICE
iSM10400 {
New
copy error:mv=<aaa...a>(<bbbb>h)<ccc...c>, rv=<aaa...a>
(<bbbb>h)<ccc...c>, status=<ddd...d>h[,ATgroup=<eee...e>]
[_ALERT_]
ERROR
Old
copy error:mv=<aaa...a>(<bbb...b>h)<ccc...c>,
rv=<aaa...a>(<bbb...b>h)<ccc...c>,status=<ddd...d>h
[UC=<eeeeeeee> FC=<ff>] ERROR
iSM10401 {
New
copy error:mv=<aaa...a>(<bbbb>h)<ccc...c>, rv=<aaa...a>
(<bbbb>h)<ccc...c>, status=<ddd...d>h[,ATgroup=<eee...e>]
[UC=<fff...f> FC=<gg>] [_ALERT_] ERROR
Old Disk array info (<aaa...a> S/N=<bbb...b>
Product-ID=<ccc...c>) [UC=<dddddddd> FC=<ee>] ERROR
iSM10403 {
New
Disk array info (<aaa...a> S/N=<bbb...b>
Product-ID=<ccc...c>) [UC=<ddd...d> FC=<ee>]
[_ALERT_]
ERROR
Old comm error:report sc=<aaa...a>h, ec=<bbb...b>h NOTICE
iSM10411 { New comm error:report sc=<aaaaaaaa>h, ec=<bbb...b>h NOTICE
Old WWPN does not exist. INFO
iSM11181 { New - -
Old - -
iSM11183 {
New Snapshot Pool doesn't exist. INFO
Old - -
iSM11184 {
New Snapshot LD doesn't exist. INFO
Appendix B Changed Message List
680
Table B-1 Message modification list (8/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old
The address which can be specified is <aaaa>h or <bbbb>h. INFO
iSM11322
{ New
The address which can be specified is “<aaaa>h” or
“<bbbb>h”. INFO
Old Cannot bind LD, because LD number exceeds the range that
can be specified.Only <aa> LDs will be able to be bound. INFO
iSM11377 {
New Cannot bind LD, because LD number of LD exceeds the range
that can be specified. Only <aa> LDs be able to be bound. INFO
Old Not enough space to bind LD.Only <aa> LDs will be able to be
bound. INFO
iSM11379 {
New Not enough space to bind LD. Only <aa> LDs be able to be
bound. INFO
Old <aa> LDs was bound successfully. But some LDs have failed
to bind. INFO
iSM11382 {
New <aa> LDs was bound successfully. But some LDs failed to
bind. INFO
Old PD (assigned as SPARE) is not found. (<aaa...a>) INFO
iSM11437 { New - -
Old Controller resource doesn't exist. (<aaa...a>) INFO
iSM11541 { New -
Old Controller detail information option is selected. (<aaa...a>) INFO
iSM11573 { New Controller detail information option was selected. (<aaa...a>) INFO
Old Enclosure detail information option is selected. (<aaa...a>) INFO
iSM11574 { New Enclosure detail information option was selected. (<aaa...a>) INFO
Old - -
iSM11583 {
New Snapshot Pool list information option was selected. INFO
Old - -
iSM11584 {
New Snapshot Pool detail information with Pool Name key option
was selected. INFO
Old - -
iSM11585 {
New Snapshot Pool detail information with Pool Number key option
was selected. INFO
Old - -
iSM11586 {
New Snapshot LD list information option was selected. INFO
Old - -
iSM11587 {
New Snapshot LD detail information option was selected. INFO
Old Conflict of target-control volume list data has been detected.
Please update volume list data. WARNING
iSM11710 {
New - -
Old Volume list data is not created by using the function of control
volume. WARNING
iSM11712 {
New Volume list data is not created by the command which supports
property display. WARNING
Old - -
iSM11713 {
New Some definitions of control volume are invalid. WARNING
Appendix B Changed Message List
681
Table B-1 Message modification list (9/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old - -
iSM11714 {
New Volume list data has no control volume. WARNING
Old - -
iSM11740 {
New Failed to get property of volume list data. ERROR
Old - -
iSM13218 {
New <aaa...a> <bbb...b> INFO
Old - -
iSM13219 {
New <aaa...a> return=<bbb...b> <ccc...c> INFO
Old Setting drive letter (aaa...a) has succeeded.
Setting mount point (bbb...b) has succeeded. INFO
iSM13220 {
New Setting drive letter (<aaa...a>) has succeeded.
Setting mount point (<bbb...b >) has succeeded. INFO
Old Resetting drive letter (aaa...a) has succeeded.Resetting mount
point (bbb...b) has succeeded. INFO
iSM13221 {
New Resetting drive letter (<aaa...a>) has succeeded. Resetting
mount point (<bbb...b>) has succeeded. INFO
Old - -
iSM13225 {
New Flush Start <aaaa/bb/cc> <dd:ee:ff> INFO
Old - -
iSM13226 {
New Flush Normal End <aaaa/bb/cc> <dd:ee:ff> INFO
Old - -
iSM13227 {
New Flush Abnormal End <aaaa/bb/cc> <dd:ee:ff> INFO
Old Scan Start INFO
iSM13228 {
New Scan Start <aaaa/bb/cc> <dd:ee:ff> INFO
Old Scan Normal End INFO
iSM13229 {
New Scan Normal End <aaaa/bb/cc> <dd:ee:ff> INFO
Old Scan Abnormal End INFO
iSM13230 {
New Scan Abnormal End <aaaa/bb/cc> <dd:ee:ff> INFO
Old Command has completed successfully. INFO
iSM13247 {
New Command has completed successfully.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) INFO
Old Command has completed successfully.(already) INFO
iSM13248 {
New Command has completed successfully.(already)
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) INFO
Old - -
iSM13250 {
New Snapshot has been deleted.
SV:<aaa...a> (code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) INFO
Old - -
iSM13251 {
New Create Start <aaaa/bb/cc> <dd:ee:ff> INFO
Appendix B Changed Message List
682
Table B-1 Message modification list (10/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old - -
iSM13252 {
New Create Normal End <aaaa/bb/cc> <dd:ee:ff> INFO
Old - -
iSM13253 {
New Create Abnormal End <aaaa/bb/cc> <dd:ee:ff> INFO
Old - -
iSM13254 {
New Delete Start <aaaa/bb/cc> <dd:ee:ff> INFO
Old - -
iSM13255 {
New Delete Normal End <aaaa/bb/cc> <dd:ee:ff> INFO
Old - -
iSM13256 {
New Delete Abnormal End <aaaa/bb/cc> <dd:ee:ff> INFO
Old Specified attribute (<aaa...a>) was already set up to
the ATgroup. ATG=<bbb...b> WARNING
iSM13403 {
New
Specified attribute (<aaa...a>) was already set up to the
ATgroup.
ATG=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<ddd...d>)
WARNING
Old Specified targets are duplicated. MV=<aaa...a> WARNING
iSM13406 { New Specified targets are duplicated. MV=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) WARNING
Old - -
iSM13406 {
New Specified targets are duplicated. volume=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) WARNING
Old These targets have replicated. ATG=<aaa...a> WARNING
iSM13408 { New These targets have replicated. ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) WARNING
Old These targets have replicated. MV:<aaa...a> RV:<aaa...a> WARNING
iSM13408 { New These targets have replicated. MV:<aaa...a> RV:<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) WARNING
Old These targets have separated. ATG=<aaa...a> WARNING
iSM13409 { New These targets have separated. ATG=<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) WARNING
Old These targets have separated. MV:<aaa...a> RV:<aaa...a> WARNING
iSM13409 { New These targets have separated. MV:<aaa...a> RV:<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) WARNING
Old These targets have restored. MV:<aaa...a> RV:<aaa...a> WARNING
iSM13410 { New These targets have restored. MV:<aaa...a> RV:<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) WARNING
Old - -
iSM13533 {
New RV name is too long. error filename=<aaa...a>
line=<bbb...b> ERROR
Old - -
iSM13533 {
New Specified volume name is too long. error filename=<aaa...a>
line=<bbb...b> ERROR
Old RV name is too long. error filename=<aaa...a>
line=<bbb...b> ERROR
iSM13534 {
New - -
Appendix B Changed Message List
683
Table B-1 Message modification list (11/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old - -
iSM13560 {
New State of the specified ATgroup is unknown.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old These targets are replicating now. MV:<aaa...a>
RV:<aaa...a> ERROR
iSM13577 {
New
These targets are replicating now. MV:<aaa...a>
RV:<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>)
ERROR
Old These targets are separating now. MV:<aaa...a>
RV:<aaa...a> ERROR
iSM13578 {
New
These targets are separating now. MV:<aaa...a>
RV:<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>)
ERROR
Old These targets are restoring now. MV:<aaa...a>
RV:<aaa...a> ERROR
iSM13579 {
New
These targets are restoring now. MV:<aaa...a>
RV:<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>)
ERROR
Old These targets have restored. ERROR
iSM13583 { New These targets have restored.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old Illegal ATgroup name. (<aaa...a>) ERROR
iSM13617 { New Illegal ATgroup name. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Old - -
iSM13624 {
New Specified volume has no mount point.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old - -
iSM13625 {
New Specified volume has more than one mount point.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old Illegal mode type. (<aaa...a>) ERROR
iSM13653 { New Illegal mode type. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Old Illegal rvuse type. (<aaa...a>) ERROR
iSM13654 { New
Illegal rvuse type. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Old Illegal condition type. (<aaa...a>) ERROR
iSM13655 { New Illegal condition type. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Appendix B Changed Message List
684
Table B-1 Message modification list (12/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old Illegal value of -interval [second]. (<aaa...a>) ERROR
iSM13656 {
New Illegal value of -interval [second]. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Old Illegal value of -limit [second]. (<aaa...a>) ERROR
iSM13657 {
New Illegal value of -limit [second]. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Old Wait command has terminated because it has reached the
time limit which is specified by the limit option. (<aaa> sec) ERROR
iSM13658 {
New
Wait command has terminated because it has reached the
time limit which is specified by the limit option. (<aaa> sec)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Old Specified targets are unavailable.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b> ERROR
iSM13659
{
New Specified targets are not available.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b> ERROR
Old - -
iSM13669 {
New SnapControl is not installed.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old - -
iSM13670 {
New ReplicationControl is not installed.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old - -
iSM13671 {
New License for DynamicSnapVolume is locked.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old - -
iSM13672 {
New DynamicSnapVolume is not supported.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old Specified attribute (<aaa...a>) does not match the attribute o
f
ATgroup. ATG=<bbb...b> ERROR
iSM13673 {
New
Specified attribute (<aaa...a>) does not match the attribute o
f
ATgroup. ATG=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<ddd...d>) ERROR
Old - -
iSM13674 {
New
Specified volume is used by snapshot function.
<aaa...a>:<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<ddd...d>) ERROR
Old - -
iSM13677 {
New Backup set name is too long. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Appendix B Changed Message List
685
Table B-1 Message modification list (13/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old - -
iSM13678 {
New Description is too long. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Old MV volume differs from database volume. ERROR
iSM13681 {
New Specified volume differs from database volume.
code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old - -
iSM13700 {
New Failed to execute command. ERROR
Old Attribute of specified volume is ‘reserve’.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
iSM13727 {
New
Attribute of specified volume is
‘<aaa...a>’.<bbb...b>:<ccc...c>
(code=<ddd...d>-<eee...e>-<eee...e>-<eee...e>) ERROR
Old Failed to <aaa...a>(<bbb...b>). drive letter (<ccc...c>) ERROR
iSM13748 {
New Failed to <aaa...a>(<bbb...b>). drive letter (<ccc...c>)
(code=<eee...e>-<fff...f>-<fff...f>-<fff...f>) ERROR
Old Failed to <aaa...a>(<bbb...b>). mount point volume
(<ddd...d>) ERROR
iSM13748 {
New Failed to <aaa...a>(<bbb...b>). mount point volume
(<ddd...d>) (code=<eee...e>-<fff...f>-<fff...f>-<fff...f>) ERROR
Old Volume list data is locked by another process. ERROR
iSM13749 {
New Volume list data is locked by another process.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old Volume list data does not exist. ERROR
iSM13750 {
New Volume list data does not exist.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old Volume type is not ld. ERROR
iSM13751 {
New Volume type is not ld.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old Timeout error has occurred in iSM/Server. ERROR
iSM13752 {
New Timeout error has occurred in iSM/Server.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old Disconnected from iSM/Server. ERROR
iSM13753 {
New Disconnected from iSM/Server.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old
Replication function of iSM/Server is not ready. ERROR
iSM13754
{
New
Replication function of iSM/Server is not ready.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old Command issue to <aaa...a> failed. ERROR
iSM13755
{
New Command issue to <aaa...a> failed.
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Appendix B Changed Message List
686
Table B-1 Message modification list (14/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old - -
iSM13761 {
New Illegal bvflg type. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Old - -
iSM13762 {
New Illegal svflg type. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Old - -
iSM13763 {
New SV is omitted.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old - -
iSM13764 {
New RV or SV is omitted.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old - -
iSM13765 {
New Replication and snapshot function are mixed in specified
pairs. (code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old - -
iSM13766 {
New Illegal option value was specified. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Old - -
iSM13767 {
New
Illegal volume type is specified. filename=<aaa...a>
line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<ddd...d>) ERROR
Old - -
iSM13768 {
New
Illegal option value was specified. filename=<aaa...a>
line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<ddd...d>) ERROR
Old - -
iSM13769 {
New Specified volume does not match the database volume.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old - -
iSM13770 {
New
State of specified pair is invalid. (state=<aaa...a>)
[BV:<bbb...b>] [SV:<ccc...c>]
(code=<ddd...d>-<eee...e>-<eee...e>-<eee...e>) ERROR
Old - -
iSM13771 {
New Specified volume is under restoration. [BV:<aaa...a>]
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Old -
iSM13772 {
New The volume under deletion exists. [BV:<aaa...a>]
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Old - -
iSM13773 {
New Specified volume is linked from LV. [{BV|SV}:<aaa...a>]
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Old - -
iSM13774 {
New Specified volume is protected by SV guard. [SV:<aaa...a>]
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Appendix B Changed Message List
687
Table B-1 Message modification list (15/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old - -
iSM13775 {
New
Deleting snapshot has terminated because
"Snap State" is changed by other process.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old - -
iSM13776 {
New
Restoring snapshot has terminated because
"Snap State" is changed by other process.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old - -
iSM13777 {
New
The volume linked from LV exists.
[BV:<aaa...a>]
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Old - -
iSM13778 {
New
The volume of SV guard exists.
[SV:<aaa...a>]
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Old - -
iSM13779 {
New
Function error has occurred. function=<aaa...a>
retcode=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<ddd...d>) ERROR
Old - -
iSM13780 {
New
Specified volume is used by replication function.
BV:<aaa...a>
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Old No such database name. filename=<aaa...a> line=<bbb...b> ERROR
iSM13800 {
New No such database name. filename=<aaa...a> line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<ddd...d>) ERROR
Old Illegal Option type is specified. filename=<aaa...a>
line=<bbb...b> ERROR
iSM13801 {
New
Illegal Option type is specified. filename=<aaa...a>
line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<ddd...d>) ERROR
Old Database name is too long. filename=<aaa...a>
line=<bbb...b> ERROR
iSM13802 {
New
Database name is too long. filename=<aaa...a>
line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<ddd...d>) ERROR
Old User id is too long. filename=<aaa...a> line=<bbb...b> ERROR
iSM13803 {
New User id is too long. filename=<aaa...a> line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<ddd...d>) ERROR
Old Password is too long. filename=<aaa...a> line=<bbb...b> ERROR
iSM13804 {
New
Password is too long. filename=<aaa...a>
line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<ddd...d>) ERROR
Appendix B Changed Message List
688
Table B-1 Message modification list (16/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old Server name is too long.filename=<aaa...a> line=<bbb...b> ERROR
iSM13805 {
New
Server name is too long.filename=<aaa...a>
line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<ddd...d>) ERROR
Old - -
iSM13806 {
New
Back up set name is too long. filename=<aaa...a>
line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<ddd...d>) ERROR
Old - -
iSM13807 {
New
Description name is too long. filename=<aaa...a>
line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<ddd...d>) ERROR
Old Illegal remod type. filename=<aaa...a> line=<bbb...b> ERROR
iSM13808 {
New
Illegal remod type. filename=<aaa...a>
line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<ddd...d>) ERROR
Old Refile name is too long. filename=<aaa...a> line=<bbb...b> ERROR
iSM13809 {
New
Refile name is too long. filename=<aaa...a>
line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<ddd...d>) ERROR
Old Specified option (<aaa...a>) is duplicated.
filename=<bbb...b> line=<ccc...c> ERROR
iSM13810 {
New
Specified option (<aaa...a>) is duplicated.
filename=<bbb...b> line=<ccc...c>
(code=<ddd...d>-<eee...e>-<eee...e>-<eee...e>) ERROR
Old OS file name is too long. filename=<aaa...a> line=<bbb...b> ERROR
iSM13811 {
New
OS file name is too long. filename=<aaa...a>
line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<ddd...d>) ERROR
Old Illegal control option. (<aaa...a>) filename=<bbb...b>
line=<ccc...c> ERROR
iSM13812 {
New
Illegal control option. (<aaa...a>) filename=<bbb...b>
line=<ccc...c>
(code=<ddd...d>-<eee...e>-<eee...e>-<eee...e>) ERROR
Old Options "pass" can not be omitted are specified.
filename=<aaa...a> line=<bbb...b> ERROR
iSM13813 {
New
Options "pass" can not be omitted are specified.
filename=<aaa...a> line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<ddd...d>) ERROR
Old Illegal combination of options. (input) filename=<aaa...a>
line=<bbb...b> ERROR
iSM13814 {
New
Illegal combination of options. (input) filename=<aaa...a>
line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<ddd...d>) ERROR
Appendix B Changed Message List
689
Table B-1 Message modification list (17/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old Options "uid" can not be omitted are specified.
filename=<aaa...a> line=<bbb...b> ERROR
iSM13815 {
New
Options "uid" can not be omitted are specified.
filename=<aaa...a> line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<ddd...d>) ERROR
Old Options "remod" and set value "standby" can not be omitted
are specified. filename=<aaa...a> line=<bbb...b> ERROR
iSM13816 {
New
Options "remod" and set value "standby" can not be omitted
are specified. filename=<aaa...a> line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<ddd...d>) ERROR
Old Specified database name is duplicated. filename=<aaa...a>
line=<bbb...b> ERROR
iSM13817 {
New
Specified database name is duplicated. filename=<aaa...a>
line=<bbb...b>
(code=<ccc...c>-<ddd...d>-<ddd...d>-<ddd...d>) ERROR
Old Failed to metafolder (<aaa...a>) creation. ERROR
iSM13818 {
New Failed to metafolder (<aaa...a>) creation.
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Old Insufficient database. (<aaa...a>) ERROR
iSM13819 {
New Insufficient database. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Old Illegal server name. (<aaa...a>) ERROR
iSM13820 {
New Illegal server name. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Old Illegal server name. (<aaa...a>) filename=<bbb...b>
line=<ccc...c> ERROR
iSM13821 {
New
Illegal server name. (<aaa...a>) filename=<bbb...b>
line=<ccc...c>
(code=<ddd...d>-<eee...e>-<eee...e>-<eee...e>) ERROR
Old Failed to get SQL server version. ERROR
iSM13822 {
New Failed to get SQL server version.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old No authority to access SQL server. ERROR
iSM13823 {
New No authority to access SQL server.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old Illegal SQL server version. ERROR
iSM13824 {
New Illegal SQL server version.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old Illegal refile name. (<aaa...a>) filename=<bbb...b>
line=<ccc...c> ERROR
iSM13826 {
New
Illegal refile name. (<aaa...a>) filename=<bbb...b>
line=<ccc...c>
(code=<ddd...d>-<eee...e>-<eee...e>-<eee...e>) ERROR
Appendix B Changed Message List
690
Table B-1 Message modification list (18/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old User id is too long. ERROR
iSM13827 {
New User id is too long.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old Password is too long. ERROR
iSM13828 {
New Password is too long.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old Server name is too long. ERROR
iSM13829 {
New Server name is too long.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old Refile name is too long. ERROR
iSM13830 {
New Refile name is too long.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old Database already exist. (<aaa...a>) ERROR
iSM13831 {
New Database already exist. (<aaa...a>)
(code=<bbb...b>-<ccc...c>-<ccc...c>-<ccc...c>) ERROR
Old Database name is too long. ERROR
iSM13832 {
New Database name is too long.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old Database operation file name is too long. ERROR
iSM13833 {
New Database operation file name is too long.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old Metafile name is too long. ERROR
iSM13834 {
New Metafile name is too long.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old Metafolder name is too long. ERROR
iSM13835 {
New Metafolder name is too long.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old Number of database exceeds the limit that can be specified. ERROR
iSM13836 {
New Number of database exceeds the limit that can be specified.
(code=<aaa...a>-<bbb...b>-<bbb...b>-<bbb...b>) ERROR
Old LD allocate time : Time=<aa>, status=<bbb...b> INFO
iSM14463 {
New - -
Old - -
iSM14467 {
New
SRA expansion : LD(SDV) number=<aaaa>h,<aaaa>h...,
Pool number=<bbbb>h, SRA capacity=<ccc...c>GB,
threshold=<ddd...d>GB(<ee>%), status=<fff...f> INFO
Appendix B Changed Message List
691
Table B-1 Message modification list (19/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old - -
iSM14468 {
New
SRA bind : LD(SDV) number=<aaaa>h,<aaaa>h..., Pool
number=<bbbb>h, SRA capacity=<ccc...c>GB,
threshold=<ddd...d>GB(<ee%>), status=<fff...f> INFO
Old - -
iSM14469 {
New
LV bind : LD(LV) number=<aaaa>h,<aaaa>h...(LD(BV)
number=<bbbb>h,<bbbb>h...), Pool number=<cccc>h,
status=<ddd...d> INFO
Old - -
iSM14470 {
New
SV bind : LD(SV) number=<aaaa>h,<aaaa>h...(LD(BV)
number=<bbbb>h), Pool number=<cccc>h, SV count=<dd>,
status=<eee...e> INFO
Old - -
iSM14471 {
New SRA unbind : Pool number=<aaaa>h, LD(SDV)
number=<bbbb>h,<bbbb>h..., status=<ccc...c> INFO
Old - -
iSM14472 {
New SV unbind : LD(SV) number=<aaaa>h,<aaaa>h...(LD(BV)
number=<bbbb>h), SV count=<cc>, status=<ddd...d> INFO
Old - -
iSM14474 {
New SRA threshold : Pool number=<aaaa>h,
threshold=<bbb...b>GB(<cc>%), status=<ddd...d> INFO
Old - -
iSM14475 {
New Configuration reserved(reference mode). : Disk
Array=<aaa...a>, status=<bbb...b> INFO
Old - -
iSM14476 {
New Configuration released(reference mode). : Disk
Array=<aaa...a>, status=<bbb...b> INFO
Old - -
iSM16001 {
New iSMalived process has started. function=<aaa...a>
AUTH=<bbb...b> INFO
Old - -
iSM16020 {
New Function Error has occurred. name=<aaa...a> code=<bbbb>
errno=<ccc> NOTICE
Old - -
iSM16021 {
New Internal Error has occurred. code=<aaaa> errno=<bbb> NOTICE
Old - -
iSM16029 {
New File does not exist. file=<aaa...a> WARNING
Old - -
iSM16030 {
New File cannot be opened. errno=<aaa> file=<bbb...b> WARNING
Old - -
iSM16031 {
New File cannot be read. file=alived.conf line=<aa> errno=<bbb> WARNING
Appendix B Changed Message List
692
Table B-1 Message modification list (20/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old - -
iSM16032 {
New Illegal configuration. file=alived.conf First line is not
[ALIVE]. WARNING
Old - -
iSM16033 {
New Illegal configuration. file=alived.conf Tag overlaps.
line=<aa> tag=<bbb...b> WARNING
Old - -
iSM16034 {
New Illegal configuration. file=alived.conf First word is not
keyword. line=<aa> WARNING
Old - -
iSM16035 {
New Illegal configuration. file=alived.conf id=<a> line=<bb> WARNING
Old - -
iSM16037 {
New Illegal configuration. file=alived.conf Specific tag is not
defined. tag=<aaa...a> WARNING
Old - -
iSM16038 {
New Illegal configuration. file=alived.conf It has exceeded 256
bytes. line=<aa> WARNING
Old - -
iSM16039 {
New Illegal configuration. file=alived.conf "TO" mail address
has exceeded 10. line=<aa> WARNING
Old - -
iSM16041 {
New File cannot be read. file=alived.tbl line=<aa> errno=<bbb> WARNING
Old - -
iSM16043 {
New Illegal configuration. file=alived.tbl Tag overlaps.
line=<aa> tag=<bbb...b> WARNING
Old - -
iSM16044 {
New Illegal configuration. file=alived.tbl First word not
keyword. line=<aa> WARNING
Old - -
iSM16045 {
New Illegal configuration. file=alived.tbl id=<a> line=<bb> WARNING
Old - -
iSM16047 {
New Illegal configuration. file=alived.tbl Specific tag is not
defined. tag=<aaa...a> WARNING
Old - -
iSM16048 {
New Illegal configuration. file=alived.tbl It has exceeded 256
bytes. line=<aa> WARNING
Old - -
iSM16049 {
New Illegal configuration. file=alived.tbl Message number has
exceeded 1000. line=<aa> WARNING
Appendix B Changed Message List
693
Table B-1 Message modification list (21/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old - -
iSM16061 {
New Mail server (<aaa...a>) address is illegal. WARNING
Old - -
iSM16062 {
New Mail server cannot be connected. name=<aaa...a>
code=<bbbb> errno=<ccc> WARNING
Old - -
iSM16063 {
New Communication error(receive from mail server).
name=<aaa...a> code=<bbbb> errno=<ccc> WARNING
Old - -
iSM16064 {
New Communication error(send to mail server). name=<aaa...a>
code=<bbbb> errno=<ccc> WARNING
Old - -
iSM16065 {
New Communication error(mail server). id=<a> send=<bbb...b>
recv=<ccc...c> WARNING
Old - -
iSM16066 {
New Mail server was time out. WARNING
Old - -
iSM16070 {
New Message buffer is full. Data losing is detected. WARNING
Old - -
iSM16071 {
New Data losing is recovered. WARNING
Old - -
iSM16080 {
New Definition change is successful. function=<aaa...a>
AUTH=<bbb...b> INFO
Old - -
iSM16081 {
New Definition change error. ALIVEmail function does not start. WARNING
Old - -
iSM16082 {
New Definition change error. ALIVEmail function continues to
operate by old one. WARNING
Old - -
iSM16083 {
New Making of file directory error. code=<aaaa> path=<bbb...b>
errno=<ccc> ERROR
Old - -
iSM16084 {
New Change directory error. name=<aaa...a> path=<bbb...b>
errno=<ccc> ERROR
Old - -
iSM18001 {
New Snapshot has been created. (<aaa...a>, BV=<bbb...b>
(<cccc>h), SV=<ddd...d>(<eeee>h)) INFO
Old - -
iSM18002 {
New
Deleting snapshot has been started. (<aaa...a>,
BV=<bbb...b> (<cccc>h), SV=<ddd...d>(<eeee>h),
generation=<fff>) INFO
Appendix B Changed Message List
694
Table B-1 Message modification list (22/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old - -
iSM18003 {
New Snapshot has been deleted. (<aaa...a>, BV=<bbb...b>
(<cccc>h), SV=<ddd...d>(<eeee>h)) INFO
Old - -
iSM18004 {
New
Restoring snapshot has been started. (<aaa...a>,
BV=<bbb...b> (<cccc>h), SV=<ddd...d>(<eeee>h),
generation=<fff>) INFO
Old - -
iSM18005 {
New Snapshot has been restored. (<aaa...a>, BV=<bbb...b>
(<cccc>h), SV=<ddd...d>(<eeee>h)) INFO
Old - -
iSM18006 {
New SV guard was changed.(<aaa...a>,
SV=<bbb...b>(<cccc>h),mode=<dd>) INFO
Old - -
iSM18007 {
New Snapshot was cancelled. (<aaa...a>, BV=<bbb...b>
(<cccc>h), SV=<ddd...d> (<eeee>h), generation=<fff>) ERROR
Old - -
iSM18008 {
New Snapshot was nullified. (<aaa...a>, BV=<bbb...b> (<cccc>h),
SV=<ddd...d> (<eeee>h), generation=<fff>) NOTICE
Old - -
iSM18201 {
New Failed to create snapshot. (<aaa...a> BV=<bbb...b>
(<cccc>h), SV=<ddd...d>(<eeee>h), code=<fff...f>) WARNING
Old - -
iSM18202
{
New
Failed to delete snapshot. (<aaa...a> BV=<bbb...b>
(<cccc>h), SV=<ddd...d>(<eeee>h), generation=<fff>,
code=<ggg...g>) WARNING
Old - -
iSM18203
{
New
Failed to restore snapshot. (<aaa...a> BV=<bbb...b>
(<cccc>h), SV=<ddd...d>(<eeee>h), generation=<fff>,
code=<ggg...g>) WARNING
Old - -
iSM18204 {
New Failed to change SV guard of snapshot-volume. (<aaa...a>,
SV=<bbb...b>(<cccc>h),code=<ddd...d>) WARNING
Old - -
iSM18205 {
New Monitoring stopped. (<aaa...a>) WARNING
Old - -
iSM18301 {
New System call error has occurred. (func=<aaa...a>,
code=<bbb...b>, errno=<cccc>) ERROR
Old - -
iSM18302 {
New Internal error has occurred. (code=<aaa...a>) ERROR
Old - -
iSM18303 {
New Parameter error has occurred. (code=<aaa...a>) WARNING
Appendix B Changed Message List
695
Table B-1 Message modification list (23/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old - -
iSM18311 {
New Internal communication error has occurred. (code=<aaa...a>) ERROR
Old - -
iSM18321 {
New Access to diskarray was failed. (<aaa...a>, code=<bbb...b>,
<ccc...c>) WARNING
Old - -
iSM18501 {
New Access mode was changed. (<aaa...a>, LD=<bbb...b>,
(<cccc>h), mode from <ddd...d> to <eee...e>) INFO
Old - -
iSM18502 {
New
Logical disk was linked to
link-volume.(<aaa...a>,LV=(<bbb...b>(<cccc>h),
LD=(<ddd...d>(<eeee>h)) INFO
Old - -
iSM18503 {
New
Logical disk was unlinked from
link-volume.(<aaa...a>,LV=<bbb...b>(<cccc>h),
LD=<ddd...d>(<eeee>h)) INFO
Old - -
iSM18601 {
New Failed to change access mode. (<aaa...a>, LD=<bbb...b>
(<cccc>h), mode=<ddd...d>), code=<eee...e>) WARNING
Old - -
iSM18602 {
New
Failed to link logical disk to
link-volume.(<aaa...a>,LV=<bbb...b>(<cccc>h),
LD=<ddd...d>(<eeee>h),code=<fff...f>) WARNING
Old - -
iSM18603 {
New
Failed to unlink logical disk from
link-volume.(<aaa...a>,LV=<bbb...b>(<cccc>h),
LD=<ddd...d>(<eeee>h),code=<fff...f>) WARNING
Old - -
iSM18999 {
New Unexpected error has occurred. (code=<aaa...a>) WARNING
Old - -
iSM19000 {
New <aaa...a> INFO
Old - -
iSM19010 {
New iSMsc_create has normally terminated. INFO
Old - -
iSM19011 {
New iSMsc_create has normally terminated. [BV:<aaa...a>]
[SV:<bbb...b>] INFO
Appendix B Changed Message List
696
Table B-1 Message modification list (24/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old - -
iSM19012 {
New iSMsc_create has abnormally terminated. INFO
Old - -
iSM19013 {
New iSMsc_create has abnormally terminated. [BV:<aaa...a>]
[SV:<bbb...b>] INFO
Old - -
iSM19020 {
New iSMsc_delete has normally terminated. INFO
Old - -
iSM19021 {
New iSMsc_delete has normally terminated. [BV:<aaa...a>]
[SV:<bbb...b>] INFO
Old - -
iSM19022 {
New iSMsc_delete has abnormally terminated. INFO
Old - -
iSM19023 {
New iSMsc_delete has abnormally terminated. [BV:<aaa...a>]
[SV:<bbb...b>] INFO
Old - -
iSM19030 {
New iSMsc_restore has normally terminated. INFO
Old - -
iSM19031 {
New iSMsc_restore has normally terminated. [BV:<aaa...a>]
[SV:<bbb...b>] INFO
Old - -
iSM19032 {
New iSMsc_restore has abnormally terminated. INFO
Old - -
iSM19033 {
New iSMsc_restore has abnormally terminated. [BV:<aaa...a>]
[SV:<bbb...b>] INFO
Old - -
iSM19034 {
New iSMsc_restore has accepted the request. INFO
Old - -
iSM19035 {
New iSMsc_restore has accepted the request. [BV:<aaa...a>]
[SV:<bbb...b>] INFO
Old - -
iSM19100 {
New The volume under restoration cannot be specified.
[BV:<aaa...a>] ERROR
Appendix B Changed Message List
697
Table B-1 Message modification list (25/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old - -
iSM19101 {
New The volume linked from LV cannot be specified.
[{BV|SV}:<aaa...a>] ERROR
Old - -
iSM19102 {
New The volume mounted cannot be specified. [BV:<aaa...a>] ERROR
Old -
iSM19103 {
New State of specified diskarray is 'freeze'. ERROR
Old - -
iSM19104 {
New The volume is not paired cannot be specified. [BV:<aaa...a>]
[SV:<bbb...b>] ERROR
Old - -
iSM19105 {
New State of specified pair is invalid. (state=<aaa...a>)
[BV:<bbb...b>] [SV:<ccc...c>] ERROR
Old - -
iSM19106 {
New The volume of SV guard cannot be specified. [SV:<aaa...a>] ERROR
Old -
iSM19107 {
New State of SV's access mode is invalid. (mode=<aaa...a>)
[SV:<bbb...b>] ERROR
Old - -
iSM19108 {
New The volume under deletion exists. [BV:<aaa...a>] ERROR
Old - -
iSM19109 {
New The volume linked from LV exists. [SV:<aaa...a>] ERROR
Old - -
iSM19110 {
New The volume of SV guard exists. [SV:<aaa...a>] ERROR
Old - -
iSM19111 {
New Version of API is invalid. ERROR
Old - -
iSM19112 {
New Specified volume is wrong.[{BV|SV}:<aaa...a>] ERROR
Old - -
iSM19113 {
New Volume list does not exist. ERROR
Appendix B Changed Message List
698
Table B-1 Message modification list (26/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old - -
iSM19114 {
New License for snapshot is locked. ERROR
Old - -
iSM19115 {
New Snapshot function is not supported with this volume. ERROR
Old - -
iSM19116 {
New Specified drive number does not exist. ERROR
Old - -
iSM19117 {
New Specified drive type is not supported.(type=<aaa...a>) ERROR
Old - -
iSM19118 {
New Specified volume does not exist in volume list.
[{BV|SV}:<aaa...a>] ERROR
Old - -
iSM19119 {
New Volume list data is locked by another process. ERROR
Old - -
iSM19120 {
New The operation to the volume specified is forbidden.
(type=<aaa...a>) ERROR
Old - -
iSM19121 {
New SV is not omissible. (Two or more SV(s) exist) ERROR
Old - -
iSM19122 {
New The volume under execution of replicaton function cannot be
specified. [BV:<aaa...a>] ERROR
Old - -
iSM19123 {
New The volume which is not recognized cannot be specified.
[BV:<aaa...a>] ERROR
Old - -
iSM19124 {
New SV of snap/inactive is already exist. INFO
Old - -
iSM19125 {
New Snapshot has been nullified. INFO
Old - -
iSM19126 {
New Specified SV has been deleted. [SV:<aaa...a>] INFO
Old - -
iSM19127 {
New Request has already completed. INFO
Old - -
iSM19200 {
New Mandatory option was not specified. (<aaa...a>) ERROR
Appendix B Changed Message List
699
Table B-1 Message modification list (27/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old - -
iSM19202 {
New Illegal option value was specified. (<aaa...a>) ERROR
Old - -
iSM19203 {
New Number of BV and SV was not equal. ERROR
Old - -
iSM19208 {
New Illegal configuration was detected.
(file=<aaa...a>,line=<bbb...b>) ERROR
Old - -
iSM19209 {
New Illegal option value was
detected.(file=<aaa...a>,line=<bbb...b>) ERROR
Old - -
iSM19210 {
New Number of BV and SV was not equal. (file
=<aaa...a>,line=<bbb...b>) ERROR
Old - -
iSM19212 {
New Duplicated targets were detected.
(file=<aaa...a>,line=<bbb...b> ) WARNING
Old - -
iSM19213 {
New Illegal volume flag was specified to be (<aaa...a>)
option.(manager specification) ERROR
Old - -
iSM19301 {
New The unexpected error has occurred in iSM/Server.
(code=aaa...a/bb/ccc...c) ERROR
Old - -
iSM19302 {
New Specified Diskarray does not exist. ERROR
Old - -
iSM19303 {
New State of Diskarray includes specified volume is not
monitoring. ERROR
Old - -
iSM19304 {
New Timeout error has occurred in iSM/Server. ERROR
Old - -
iSM19305 {
New The timeout was detected by waiting of communication with
iSM/Server. ERROR
Old - -
iSM19306 {
New Failed to connect iSM/Server.(errno=<aaa...a>, phase=<
bbb...b>) ERROR
Appendix B Changed Message List
700
Table B-1 Message modification list (28/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old - -
iSM19307 {
New Failed to receive from iSM/Server.(errno=<aaa...a>,
phase=< bbb...b >) ERROR
Old - -
iSM19308 {
New Failed to send to iSM/Server.(errno=<aaa...a>,
phase=<bbb... b>) ERROR
Old - -
iSM19401 {
New System call error has occurred.(func=<aaa...a>,
errno=<bbbb>, phase=<ccc...c>) ERROR
Old - -
iSM19402 {
New Unexpected error occurred. (phase=<aaa...a>) ERROR
Old - -
iSM19403 {
New Failed to mount. ERROR
Old - -
iSM19404 {
New Failed to umount. ERROR
Old - -
iSM19405 {
New Collecting information of display was failed. ERROR
Old - -
iSM19408 {
New Data on SV has been removed. [SV:<aaa...a>] INFO
Old - -
iSM20000 {
New <aaa...a> INFO
Old - -
iSM20010 {
New iSMsc_chgmod has normally terminated. INFO
Old - -
iSM20011 {
New iSMsc_chgmod has normally terminated. [vol:<aaa...a>] INFO
Old - -
iSM20012 {
New iSMsc_chgmod has abnormally terminated. INFO
Old - -
iSM20013 {
New iSMsc_chgmod has abnormally terminated. [vol:<aaa...a>] ERROR
Appendix B Changed Message List
701
Table B-1 Message modification list (29/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old - -
iSM20020 {
New iSMsc_link has normally terminated. INFO
Old - -
iSM20021 {
New iSMsc_link has normally terminated. [LV:<aaa...a>]
[SV:<bbb...b>] INFO
Old - -
iSM20022 {
New iSMsc_link has abnormally terminated. INFO
Old - -
iSM20023 {
New iSMsc_link has abnormally terminated. [LV:<aaa...a>]
[SV:<bbb...b>] INFO
Old - -
iSM20030 {
New iSMsc_unlink has normally terminated. INFO
Old - -
iSM20031 {
New iSMsc_unlink has normally terminated.
[LV:<aaa...a>][SV:<bbb...b>] INFO
Old - -
iSM20032 {
New iSMsc_unlink has abnormally terminated. INFO
Old - -
iSM20033 {
New iSMsc_unlink has abnormally terminated.
[LV:<aaa...a>][SV:<bbb...b>] INFO
Old
iSM20100 {
New Unpaired volumes cannot be specified. [SV:<aaa...a>] ERROR
Old - -
iSM20101 {
New The volume from which capacity is different cannot be
specified. [LV:<aaa...a>] [{BV|SV}:<bbb...b>] ERROR
Old - -
iSM20102 {
New The Volume from which volume type is different type cannot
be specified. [LV:<aaa...a>] [{BV|SV}:<bbb...b>] ERROR
Old - -
iSM20103 {
New Specified volume has another link. [{LV|BV|SV}:<aaa...a>] ERROR
Old - -
iSM20104 {
New State of SV's access mode is invalid. (mode=<aaa...a>)
[SV:<bbb...b>] ERROR
Appendix B Changed Message List
702
Table B-1 Message modification list (30/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old - -
iSM20106 {
New Targets volumes are not linked. [LV:<aaa...a>] [{BV|SV}:<
bbb...b>] ERROR
Old - -
iSM20107 {
New The volume mounted cannot be specified. [LV:<aaa...a>] ERROR
Old - -
iSM20108 {
New SV which is not snap/active cannot be specified.
[SV:<aaa...a>] ERROR
Old - -
iSM20109 {
New The volume which is not link target volume cannot be
specified. [{BV|SV}:<aaa...a>] ERROR
Old - -
iSM20112 {
New Specified volume is wrong. [{LV|BV|SV|VOL}:<aaa...a>] ERROR
Old - -
iSM20116 {
New Version of API is invalid. ERROR
Old - -
iSM20117 {
New License for snapshot is locked. ERROR
Old - -
iSM20118 {
New Snapshot function is not supported with this volume. ERROR
Old - -
iSM20119 {
New Specified volume does not exist in volume list.
[{BV|SV|LV|VOL}:<aaa...a>] ERROR
Old - -
iSM20120 {
New Link information does not exist. [VOL:<aaa...a>] ERROR
Old - -
iSM20121 {
New The volume which is not recognized cannot be specified.
[BV:<aaa...a>] ERROR
Appendix B Changed Message List
703
Table B-1 Message modification list (31/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old - -
iSM20122 {
New The volume which is not linked cannot be specified.
[VOL:<aaa...a>] ERROR
Old - -
iSM20123 {
New State of specified diskarray is 'freeze'. ERROR
Old - -
iSM20200 {
New Mandatory option was not specified.(<aaa...a>) ERROR
Old - -
iSM20201 {
New Illegal option was specified.(<aaa...a>) ERROR
Old - -
iSM20202 {
New Illegal option value was specified.(<aaa...a>) ERROR
Old - -
iSM20203 {
New Specified volume group does not exist.(vg=<aaa...a>) ERROR
Old - -
iSM20204 {
New Specified disk group does not exist.(dg=<aaa...a>) ERROR
Old - -
iSM20205 {
New Duplicated targets were detected. (file=<aaa...a>,
line=<bbb...b> ) WARNING
Old - -
iSM20206 {
New Specified file does not exist. (file=<aaa...a>) ERROR
Old - -
iSM20207 {
New Specified file is invalid.(illegal file type) (file=<aaa...a>) ERROR
Old - -
iSM20208 {
New Illegal configuration was detected. (file=<aaa...a>,
line=<bbb...b>) ERROR
Old - -
iSM20209 {
New Illegal option value was detected. (file=<aaa...a>,
line=<bbb...b>) ERROR
Old - -
iSM20210 {
New Empty file cannot be specified. (file=<aaa...a>) ERROR
Old - -
iSM20211 {
New Illegal volume flag was specified to be (<aaa...a>)
option.(manager specification) ERROR
Old - -
iSM20301 {
New The unexpected error has occurred in iSM/Server.
(code=aaa...a/bb/ccc...c) ERROR
Appendix B Changed Message List
704
Table B-1 Message modification list (32/32)
Modification Description
Message ID
Added Changed Deleted
iSM
version Message body Classification
Old - -
iSM20302 {
New Specified Diskarray does not exist. ERROR
Old - -
iSM20303 {
New State of Diskarray includes specified volume is not
monitoring. ERROR
Old - -
iSM20304 {
New Timeout error has occurred in iSM/Server. ERROR
Old - -
iSM20305 {
New The timeout was detected by waiting of communication with
iSM/Server. ERROR
Old - -
iSM20306 {
New Failed to connect iSM/Server.(errno=<aaa...a>,
phase=<bbb... b>) ERROR
Old - -
iSM20307 {
New Failed to receive from iSM/Server.(errno=<aaa...a>,
phase=<bbb... b>) ERROR
Old - -
iSM20308 {
New Failed to send to iSM/Server.(errno=<aaa...a>,
phase=<bbb... b>) ERROR
Old - -
iSM20401 {
New System call error has occurred.(func=<aaa...a>,
errno=<bbbb>, phase=<ccc...c>) ERROR
Old - -
iSM20402 {
New Unexpected error occurred. (phase=<aaa...a>) ERROR
Old - -
iSM20403 {
New SCSI I/O error is detected. (device=aaaa, cdb
=bbbb,status=cccc/dddd/ee/ff/gg) ERROR
Old - -
iSM20404 {
New Control path is blockaded. (device=aaaa, cdb
=bbbb,status=cccc/dddd/ee/ff/gg) WARNING
Old - -
iSM20405 {
New Illegal device is specified. (<aaa...a>) ERROR
Old - -
iSM20406 {
New Failed to umount. ERROR

Navigation menu