Nedap N V BOOSTER10 Long-range vehicle and driver identification tag User Manual Report

N. V. Nederlandsche Apparatenfabriek NEDAP Long-range vehicle and driver identification tag Report

15_Manual CGDBOOSTER10

BOOSTER installation guide Prox-Booster Smartcard-Booster 2G Smartcard-Booster Ultimate 19-05-2015 | v4.2
BOOSTER 2G | USER GUIDE Content 2/27 CONTENT 1 INTRODUCTION _______________________________________________________ 3 2 INSTALLATION ________________________________________________________ 4 2.1 DIMENSIONS ___________________________________________________ 4 2.2 TEMPERATURE CONSIDERATIONS __________________________________ 4 2.3 SOLAR CONTROL WINDSHIELDS ___________________________________ 5 2.4 PROX-BOOSTER TACHO __________________________________________ 5 3 IDENTIFYING THE BOOSTER WITH A TRANSIT ______________________________ 6 3.1 HOW TO USE THE BOOSTER _______________________________________ 6 3.2 READER OUTPUT BOOSTER INFO ___________________________________ 6 3.3 READER OUTPUT TACHO INFO _____________________________________ 7 4 SMARTCARD CONFIGURATION ___________________________________________ 9 4.1 CONFIGURATION PROCEDURE ____________________________________ 9 4.2 HOW TO CREATE A CONFIGURATION CARD __________________________ 9 4.2.1 TARGET DEVICE __________________________________________ 10 4.2.2 CREATION PROCEDURE ___________________________________ 10 4.2.3 DEFAULT CONFIGURATION ________________________________ 17 4.3 ROGRAM THE CONFIGURATION CARD _____________________________ 18 4.3.1 USING A SUPPORTED PROGRAMMER ________________________ 18 4.3.2 USING ANOTHER PROGRAMMER____________________________ 19 4.4 TESTING THE CONFIGURATION ___________________________________ 20 4.5 CONFIGURATION FILES __________________________________________ 20 5 MTR CONFIGURATION _________________________________________________ 21 6 BUZZER INDICATIONS _________________________________________________ 22 7 BATTERY REPLACEMENT _______________________________________________ 23 A TECHNICAL SPECIFICATIONS ___________________________________________ 24 B FCC / IC STATEMENT __________________________________________________ 25 C DISCLAIMER _________________________________________________________ 26 D DOCUMENT REVISION _________________________________________________ 27
BOOSTER 2G | USER GUIDE Introduction 3/27 1 INTRODUCTION The Prox-Booster and Smartcard-Boosters are dual ID tags enabling simultaneous identification of the inserted personal ID card and the embedded vehicle ID resulting in rapid driver and vehicle monitoring. The Prox-Booster Tacho additionally sends the tacho-counter value, which relates to the travelled distance of the vehicle. The Booster allows an inserted Proximity or Smartcard driver ID card and embedded vehicle ID to be read from a distance up to 10 meters (33 feet) in combination with NEDAP TRANSIT readers. This solution substantially enhances the level of security when controlling activities of vehicles that are regularly used by different drivers. Additionally a fully integrated vehicle and personnel access solution can be implemented. The Smartcard-Booster Ultimate additionally supports encrypted authentication using diversified AES128 bit keys, in combination with the TRANSIT Ultimate and the Security Key Pack. For more details about the NEDAP TRANSIT Standard or Ultimate reader refer to the corresponding installation guide. The combined vehicle and driver ID is a unique NEDAP patented feature. Optionally the vehicle-ID can be sacrificed if more information from the personal ID card is required. The following personal ID card types are identified with the Boosters: • Prox-Booster (tacho) NEDAP, EM and HID PROX • Smartcard-Booster (Ultimate) MIFARE (incl. Desfire EV1), HID iCLASS, ISO14443A, ISO15693 and Calypso. CAUTION: DO NOT LEAVE CARD IN ACCESS DEVICE WHEN LEAVING THE VEHICLE, AS THIS PRESENTS A SECURITY RISK. CAUTION: DO NOT LEAVE CARD IN ACCESS DEVICE FOR LONG PERIODS OF TIME IN EXTREME HEAT, AS THIS MAY DAMAGE THE CARD.
BOOSTER 2G | USER GUIDE Installation 4/27 2 INSTALLATION 2.1 DIMENSIONS The Boosters are easily mounted to the inside of the car’s windshield by means of suction cups. Users should ensure the visual contact between the Booster and any TRANSIT reader is unobstructed with items such as stickers or metallized windshields (see also chapter 2.3 about solar control windshields). Note that the Booster's suction cups must be faced toward the reader to achieve maximum reading distance. Dimension Length X 111 mm 4.37 " Width Y 65 mm 2.56 " Height Z 32 mm 1.26 " Body height H 24 mm 0.95 " Tacho wire wire length 1700 mm 67 " wire thickness 2 x 0.25 mmP2 2 x AWG 23 Booster Dimensions 2.2 TEMPERATURE CONSIDERATIONS The Booster is designed to operate within the extreme temperature ranges, which often occur behind a vehicle’s windshield during the winter or summer seasons (-20°C to 85°C / -4°F to +185°F). However the personal identification card inserted in the Booster may not be designed to withstand such temperatures and could suffer damage as a result. Nedap recommends to remove the personal identification card when not in use. X Y H Z
BOOSTER 2G | USER GUIDE Installation 5/27 2.3 SOLAR CONTROL WINDSHIELDS From 1997 onwards several car manufacturers introduced vehicles with solar control windshields. The solar control windshields are equipped with a metalized coating, which can block the TRANSIT signal from the Booster mounted on the inside of the windshield of the vehicle. Most of these windshields have a metal free zone where transponders can be mounted. The metal free zone of metalized windshields is most often found in the middle of the windshield behind and slightly below the rear view mirror. In vehicles manufactured after 1998 the metal free zone should be indicated on the window. We advise the owner to contact the local car dealer if it is not clear where the aperture is exactly positioned in a certain vehicle and where the transponder should be mounted. 2.4 PROX-BOOSTER TACHO The prox-booster tacho is a special booster version that should be wired to the speed pulse generator of your vehicle. The exact wiring details and connection location very much depend upon the brand, type and model of your vehicle. Contact your vehicle dealer for more information about the speed pulse generator in your vehicle. Tacho input specifications: • Input voltage: 6V to 24V (max. 30V). • Polarity reversal tolerant. • Input prescaler 1:256. • Maximum pulse frequency 850Hz. • Maximum vehicle speed 255km/h (at 12 pulses/meter). hkm /2556.312850 =×=.
BOOSTER 2G | USER GUIDE Identifying The Booster With A TRANSIT 6/27 3 IDENTIFYING THE BOOSTER WITH A TRANSIT 3.1 HOW TO USE THE BOOSTER Place the Booster on the inside of the windscreen of your vehicle as described in chapter 2. The driver inserts his personal identification card and activates the Booster’s button. A beep should indicate that the card was successfully read. A low beep indicates that card reading failed. The TRANSIT reader can identify your card up to a distance of 10 meters (=33 ft). After 5 seconds the Booster returns into sleep mode. The booster will remain active when in 'always-on'-mode. The driver should remove his personal identification card from the Booster when leaving the vehicle. 3.2 READER OUTPUT BOOSTER INFO The Prox/Smartcard-Booster is a battery operated passive tag. The information from the tag is sent to the reader by a method called modulated backscatter. This means that the 2.45GHz signal coming from the reader's antenna is modified in such way that it can be recognized by the reader. The examples below assume that a TRANSIT reader with P81 firmware is used and show the messages transmitted on the RS-232 interface to a host system (TXD). Refer to the TRANSIT firmware manuals for more details about the reader communication protocol. Combi-Booster mode (Vehicle-ID + Driver-ID) The Booster cannot be identified until the driver inserts his personal identification card and pushes the Booster’s button. Once the button is pushed the Booster reads the personal identification card and beepsP upon a successful read. Both vehicle-id and driver-id are tfransmitted to the host system for 5 seconds. Afterwards the Booster automatically deactivates again. The booster will remain active when in 'always-on'-mode. Example vehicle-id = 123, driver-id = E4947C46, TXD = Y000000012300000000000000E4947C46PCPRRRPLPRFR If 'Standard-length' is configured, the following message is transmitted to the host. TXD = U000000012300E4947C46PCPRRRPLPRF Event identifier ('Y' or 'U'). Vehicle-id (10 digits). Driver-id (10 or 22 digits). Booster mode (Only Driver-ID) The Booster is 'sleeping' until the driver inserts his personal identification card and pushes the Booster’s button. Once the button is pushed the Booster reads the personal identification card and beepsP upon a successful read. The data is transmitted to the host system for 5 seconds. After that the Booster automatically deactivates again. The booster will remain active when in 'always-on'-mode. Note See chapter 6 for details about the buzzer indications.
BOOSTER 2G | USER GUIDE Identifying The Booster With A TRANSIT 7/27 Example driver-id = 871111111117100944, TXD = Z00000000000000871111111117100944PCPRRRPLPRFR If 'Standard-length' is configured, the following message is transmitted to the host. TXD = U00871111111117100944PCPRRRPLPRF Event identifier ('Z' or 'U'). Driver-id (20 or 32 digits). 3.3 READER OUTPUT TACHO INFO Tacho-Booster mode (Vehicle-ID + Driver-ID + Tacho-Counter) The prox-booster tacho should be connected to the speed pulse generator of your vehicle. The prox-booster will count the number of pulses generated. The Booster cannot be identified until the driver inserts his personal identification card and pushes the Booster’s button. Once the button is pushed the Booster reads the personal identification card and beepsP upon a successful read. Both vehicle-id, driver-id and tacho-counter are transmitted to the host system for 5 seconds. Afterwards the Booster automatically deactivates again. The tacho counter will be updated while the booster is deactivated. The booster will remain active when in 'always-on'-mode. Example reader output: vehicle-id = 123, driver-id = E4947C46, tacho-counter = 2AC4, TXD = X000000012300E4947C468000002AC4PCPRRRPLPRFR Event identifier ('X' = triple identifier detection event). Vehicle-id (10 digits). Driver-id (10 digits). Additional data identifier ('80' = tacho counter). Additional data (in this case the tacho counter value). How to calculate the constant factor required to convert tacho counter value into travelled distance. • Get the vehicle's initial mileage )(1M= and the initial tacho counter value )( 1T=. • Drive the vehicle for a significant amount of miles (or kilometers). • Then again get the actual mileage )( 2M= and the actual tacho counter value )( 2T=. • Now calculate the number of counts per mile (or km) by using the following formula: ( )( )1212MMTTK−−=
BOOSTER 2G | USER GUIDE Identifying The Booster With A TRANSIT 8/27 How to calculate the vehicle's travelled distance. • Get the actual tacho counter value )( nT= • Calculate travelled distance by using the following formula: ( )KTTDnn1−= • Calculate the current mileage by using the following formula: 1MDMnn+=.
BOOSTER 2G | USER GUIDE Smartcard Configuration 9/27 4 SMARTCARD CONFIGURATION The Smartcard-Booster can be configured by means of a configuration card. This configuration card is a Mifare Classic 1K or 4K card that is programmed with the configuration settings. Configuration is only required if the factory default settings are not sufficient. The default settings are described in chapter 4.2.3. 4.1 CONFIGURATION PROCEDURE Every Booster used in the application should be configured with the configuration card. The simple configuration procedure is described below. Insert the configuration card in the Booster and push the button. The Booster sounds the buzzer with an increasing frequency (♪ ♪ ♪) to indicate that the configuration card is accepted. 4.2 HOW TO CREATE A CONFIGURATION CARD NEDAP has developed a software application that allows system integrators to create configuration cards. This software can be downloaded from our website 1TUwww.Nedapidentification.comU1T Smartcard-Booster Config software
BOOSTER 2G | USER GUIDE Smartcard Configuration 10/27 4.2.1 TARGET DEVICE The Booster Configuration software can be used to configure a number of different devices. The user-interface is adapted to the selected target device. Select in the ‘Target’ menu which device you are about to configure. • Smartcard-Booster • Transition Booster • Prox Booster EM4x50 not covered in this manual • MTR Module see chapter 5 4.2.2 CREATION PROCEDURE Follow the procedure below to create a configuration card with application specific settings. 1 Specify OPERATING MODE (see chapter 4.2.2.1) 2 Specify FRAME LENGTH (see chapter 4.2.2.2) 3 Specify ACTIVE_MODE (see chapter 4.2.2.3) 4 Specify RFID CONFIGURATION settings (see chapter 4.2.2.4) 5 Save the configuration settings into a file. 6 Write the configuration into a blank Mifare Classic 1K or 4K card. Operating mode Booster (only Driver-ID) Up to 16 bytes of data from the personal identification card is read. The Vehicle-ID is omitted. Combi-Booster (Vehicle-ID + Driver-ID) Vehicle-ID combined with up to 11 bytes from the personal identification card is read. Tacho-Booster (Vehicle-ID + Driver-ID + Tacho-Counter) Vehicle-ID and Driver-ID combined with Tacho-Counter value. If this option is selected than automatically extended-length is selected. Frame length This affects the length of the message sent to TRANSIT reader. Extended length (longer Driver-ID) Select extended-length in order to support all transponder types and maximum amount of data. The extended-length may be not compatible with older firmware versions in the TRANSIT reader. You might need to upload new firmware into the reader. The identification speed is a bit slower compared to applying standard-length. Standard length (backwards compatible, faster identification) Select standard-length in applications where compatibility with older types of transponders or where fast identification is important. Please note that when reading low-frequency cards with a Transition-Booster this setting is not used. For NEDAP and EM cards the extended-length is not required and therefore the Booster will automatically use standard-length (even if extended-length is selected in the configuration). For HID PROX the extended-length is required so extended-length is used automatically if such a card is identified (even if
BOOSTER 2G | USER GUIDE Smartcard Configuration 11/27 standard-length is selected in the configuration). Active mode Two activation modes are possible: Switched or Always-on. The setting can only be changed when the Booster originally was in switched mode !!! Switched mode is selected when the operating mode is Booster (only Driver-ID). Switched mode (active for approx. 5 seconds) In switched mode the booster is active for approx. 5 seconds after the booster's button is pushed and then autmatically returns into sleep mode. Always-on (continuously active) In always-on mode the booster remains active. When the booster's button is pushed the booster will read the inserted card. If a card is identified, the booster will check every few minutes if the inserted card is still present. RFID Configuration ISO14443-A / MIFARE Enable or disable the reading of ISO14443-A / MIFARE cards. Data to read: For ISO14443-A cards the card serial number can be read. The cascaded card serial number (e.g. used in Mifare UltraLight cards) is also supported. For MIFARE cards also other encrypted information from the card can be read. Select one of the following choices: • ISO14443-A card serial number • MIFARE UltraLight data (see chapter 4.2.2.5 for more details) • MIFARE Classic sector data (see chapter 4.2.2.6 for more details) • MIFARE DESFIRE file data (see chapter 4.2.2.7 for more details) The byte order can be set to normal or reversed. Nedap PM Enable or disable the reading of NEDAP PM cards. NEDAP PM cards are always transmitted to the TRANSIT using standard-length. EM4102 (and compatible) Enable or disable the reading of EM4102 and compatible cards. EM4102 cards are always transmitted to the TRANSIT using standard-length. HID PROX Enable or disable the reading of HID PROX cards. HID PROX cards are always transmitted to the TRANSIT using extended-length. HID iCLASS CSN Enable or disable the reading of HID iCLASS cards. Only the card serial number can be read from these cards. ISO15693 / LEGIC Advant CSN Enable or disable the reading of ISO15693 / LEGIC Advant cards. Only card serial number can be read from these cards. Note The Nedap PM, EM4102 and HID PROX are not supported on the Smartcard-Booster. Note The EM4102 cannot be disabled on MTR.
BOOSTER 2G | USER GUIDE Smartcard Configuration 12/27 Calypso Enable or disable the reading of Calypso cards. Data to read: For Calypso cards the 4-byte PUPI or information from always accessible files can be read. The Booster does not support the Calypso SAM to fully support the Calypso encrypted file system. Select one of the following choices: • PUPI (pseudo unique PICC identifier) • Calypso file data Byte order The byte order can be set to normal or reversed. Short File Identifier Calypso SFI (Short File Identifier) in range from 1 .. 30. Some files have no SFI. Only files with an SFI are supported. Record Number A file may contain more than one record. Numbered from 1 to the maximum number of records. Data Length Number of bytes to transmit. The maximum number of bytes is dependent upon the operating-mode and frame-length settings. Data Offset Number of bytes to skip. Reading MIFARE ultralight data The Mifare UltraLight transponders’ 512 bit EEPROM memory is organized in 16 pages with 4 bytes each. Page Number Page number to start reading from (in range from 0 .. 15). Always 4 pages are read. The reading will wrap around to page number 0 if additional data after page 15 should be read. Data Length Number of bytes to transmit. The maximum number of bytes is dependent upon the operating-mode and frame-length settings. Data Offset Number of bytes to skip.
BOOSTER 2G | USER GUIDE Smartcard Configuration 13/27 Example Data to read: MIFARE UltraLight data Byte order: Normal Page Number: 4 Data Length: 8 Data Offset: 2 Always 16 bytes are read from the card and in this example the reading starts at page 4, thus pages 4, 5, 6 and 7 are read. The first 2 bytes are skipped because the offset is set to 2. The following 8 bytes are transmitted because the configured data length is 8. Byte 0 Byte 1 Byte 2 Byte 3 Page 4 skipped skipped DATA DATA Page 5 DATA DATA DATA DATA Page 6 DATA DATA ignored ignored Page 7 ignored ignored ignored ignored Reverse example Data to read: MIFARE UltraLight data Byte order: Reverse Page Number: 5 Data Length: 10 Data Offset: 6 Always 16 bytes are read from the card and in this example the reading starts at page 5, thus pages 5, 6, 7 and 8 are read. After the byte order is reversed, the first 6 bytes are skipped because the offset is set to 6. The following 10 bytes are transmitted because the configured data length is 10. Byte 3 Byte 2 Byte 1 Byte 0 Page 8 skipped skipped skipped skipped Page 7 skipped skipped DATA DATA Page 6 DATA DATA DATA DATA Page 5 DATA DATA DATA DATA
BOOSTER 2G | USER GUIDE Smartcard Configuration 14/27 Reading MIFARE classic sector data The Mifare Classic 1K and 4K cards are fully supported. Also other Mifare cards which are compatible (such as Mifare Plus and SmartMX) can be used. The memory is organized in sectors with blocks. Every block consists of 16 bytes. Upon configuring the smartcard-booster for reading MIFARE DESFIRE cards, the following parameters must be specified. Sector Number Sector number to read data from (in range from 0 .. 39). Block Number Block number to read data from. The block number must be in range from 0.. 3 for the first 32 sectors. For the sectors 32 .. 39 the block number can range from 0 .. 15. Data Length Number of bytes to transmit. The maximum number of bytes is dependent upon the operating-mode and frame-length settings. Data Offset Number of bytes to skip. Read Key Key A or Key B can be used to authenticate to the card. Select which key to use and the key itself. Example Data to read: MIFARE Classic sector data Byte order: Normal Sector Number: 1 Block Number: 1 Data Length: 8 Data Offset: 2 The settings above will read the data below shown in blue. Sector Block 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 0 x x x x x x x x x x x x x x x x 1 x x D D D D D D D D x x x x x x 2 x x x x x x x x x x x x x x x x 3 x x x x x x x x x x x x x x x x
BOOSTER 2G | USER GUIDE Smartcard Configuration 15/27 Reverse example Data to read: MIFARE Classic sector data Byte order: Reverse Sector Number: 2 Block Number: 0 Data Length: 10 Data Offset: 6 The settings above will read the data below shown in blue. Sector Block 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 2 0 x x x x x x D D D D D D D D D D 1 x x x x x x x x x x x x x x x x 2 x x x x x x x x x x x x x x x x 3 x x x x x x x x x x x x x x x X Reading MIFARE DESFIRE file data The MIFARE DESFIRE cards are fully supported. Also other newer DESFIRE EV1 cards can be used. Including the DES, 3DES, 3 Key 3DES and AES encryptions. The DESFIRE card's memory is organized using a flexible file system. This file system allows several different applications on a single card. Every application is identified by its 3 byte application identifier (AID). Each application may contain up to 32 files. Upon configuring the smartcard-booster for reading MIFARE DESFIRE cards, the following parameters must be specified. Application ID Three byte application identifier (AID). File number File number in the range from 0 .. 31. Communication mode Plain. Plain secured by MACing. Fully enciphered. Data Length Number of bytes to transmit. The maximum number of bytes is dependent upon the operating-mode and frame-length settings. Data Offset Number of bytes to skip. Encryption None (skip authentication) Native DES/3DES ISO DES/3DES 3 Key 3DES
BOOSTER 2G | USER GUIDE Smartcard Configuration 16/27 AES Key number Key number in range from 0 to 13. Key Security authentication key. Depending upon the selected encryption method and key number. The encryption key is 16 or 24 bytes.
BOOSTER 2G | USER GUIDE Smartcard Configuration 17/27 4.2.3 DEFAULT CONFIGURATION In the table below the default configuration is shown. Configuration settings Default value Operating mode Combi-Booster (Vehicle-ID + Driver-ID) Frame length Extended-length (longer Driver-ID) Active mode Switched mode ISO14443-A / MIFARE Enabled Data to read ISO14443-A card serial number Byte order Normal NEDAP PM Enabled EM4102 (and compatible) Enabled HID PROX Enabled HID iCLASS CSN Enabled ISO15693 / LEGIC Advant CSN Enabled Calypso Enabled Data to read PUPI Byte order Normal
BOOSTER 2G | USER GUIDE Smartcard Configuration 18/27 4.3 ROGRAM THE CONFIGURATION CARD 4.3.1 USING A SUPPORTED PROGRAMMER The software supports a few different programming devices. The NXP Pegoda, the HID OMNIKEY 5x21 and PC/SC contactless readers from the Springcard CSB6 Family (e.g. Prox 'n' Roll PC/SC). NXP Pegoda Programmer Connect the NXP Pegoda Mifare programmer to a USB port on your computer. USB drivers must be installed as described in the NXP documentation. In the ‘Programmer’ menu select the 'NXP Pegoda' and click ‘Connect’ to connect to the programmer. HID OMNIKEY 5x21-CL Programmer Connect the HID OMNIKEY 5x21-CL USB programmer to a USB port on your computer. USB drivers must be installed as described in HID documentation. In the ‘Programmer’ menu select 'HID OMNIKEY' and click ‘Connect’. SPRINGCARD CSB6 The SpringCard CSB6 and Prox 'n' Roll PC/SC share the same architecture. Install the PC/SC drivers as described in the SpringCard documentation. Connect the CSB6 to a USB port on your computer. In the ‘Programmer’ menu select 'SpringCard CSB6' and click ‘Connect’. Programming Once the connection has been established and all configuration settings are entered, place an empty Mifare Classic 1K or 4K card on the programmer. To program the configuration into the Mifare card click ‘Write configuration into card’ in the ‘Programmer’ menu. The message ‘Configuration written into card’ should appear to indicate that the programming action was successful. The software will warn you with the message ‘Overwrite configuration card’ if there is already a configuration on the Mifare card. Click ‘Yes’ to proceed and overwrite the configuration on the card or click ‘No’ to abort. Read back It is also possible to read back what configuration is programmed into a configuration card. Click ‘Read configuration from card’ in the ‘Programmer’ menu. Note The HID OMNIKEY programmer sometimes requires to remove and replace the config card before re-accessing the card is possible.
BOOSTER 2G | USER GUIDE Smartcard Configuration 19/27 4.3.2 USING ANOTHER PROGRAMMER If there is no supported programmer available you can use any other Mifare programmer to write the configuration into a Mifare classic card. The configuration data should be written into sector 1 and 2 of a Mifare Classic 1K or 4K card. The contents of these sectors is not explained, but can be shown by the configuration software by clicking ‘Show configuration details’ in the ‘Expert’ menu. Configuration Data Sector 0 is reserved for MAD (Mifare Application Directory). If the MAD is programmed, the Nedap configuration sectors should have application id 517F. Copy to clipboard Copy the configuration data to clipboard by clicking ‘Copy to clipboard’ in the ‘Edit’ menu. Customizing view In the ‘View’ menu the viewing can be customized in such way that it best matches your programming software. Click ‘Change Hex Prefix…’ to specify a specific prefix that is shown before every configuration data byte. Below is shown the configuration data with prefix ‘0x’. 0x77 0x77 0x77 0x2E 0x6E 0x65 0x64 0x61 0x70 0x61 0x76 0x69 0x2E 0x63 0x6F 0x6D 0x4E 0x01 0x01 0x07 0x07 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x4E 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xA0 0xA1 0xA2 0xA3 0xA4 0xA5 0x78 0x77 0x88 0x00 0xB0 0xB1 0xB2 0xB3 0xB4 0xB5 Besides the hex prefix also the byte order can be changed from within the ‘View’ menu.
BOOSTER 2G | USER GUIDE Smartcard Configuration 20/27 4.4 TESTING THE CONFIGURATION The MIFARE settings can be tested before loading it into the Smartcard-Booster using a supported mifare reader. From the ‘Programmer' menu choose ‘Test configuration’. Place the Mifare card (not the config card) on the reader and click the ‘Read’ button. The reader reads the Mifare card according to the current configuration settings. The software displays the driver-id number as it will be identified by the TRANSIT. Configuration Test If the card is not read or if the wrong data is shown under DRIVER-ID then check if the configuration settings are correct. Remember that only MIFARE cards can be tested this way. 4.5 CONFIGURATION FILES Your configuration can be saved into a so-called Smartcard Booster Config File (*.sbcf). These files contain all the configuration settings as you have defined them. Saved Config Files can be easily opened from within the File menu.
BOOSTER 2G | USER GUIDE MTR Configuration 21/27 5 MTR CONFIGURATION The MTR Module (Multi-Technology Reader) is especially designed to read low-frequency proximity cards and ISO compliant smartcards directly on the TRANSIT Entry reader at short range without Booster. The MTR is configured in exactly the same way as the Smartcard Booster. Refer to chapter 4 on page 9 for more information about the configuration procedure. For more details about the TRANSIT Entry reader and the MTR refer to the separate documentation.
BOOSTER 2G | USER GUIDE Buzzer Indications 22/27 6 BUZZER INDICATIONS The Booster's built-in buzzer gives audible feedback upon various conditions. The table below describes the buzzer indications. Buzzer Description 1 beep Card read 1 short low beep Failed to read card (not in configuration) 3 beeps increasing frequency ♪ ♪ ♪ Configuration card accepted 6 beeps increasing frequency Power on (Smartcard-Booster / MTR) 3 beeps Power on (Prox-Booster)
BOOSTER 2G | USER GUIDE Battery Replacement 23/27 7 BATTERY REPLACEMENT The Smartcard-Booster contains two replaceable non-rechargeable AAA batteries. The average lifetime of these batteries is approximately 5 years. When replacement becomes necessary follow the procedure below. • 1 Open the battery compartment. • Remove both batteries. Follow local environment protection laws / regulations for disposal of used batteries. • Replace with two new batteries. Make sure that the polarity matches the indicated polarity. Refer to appendix A for battery requirements. • Close the battery compartment and verify if the booster is working properly.
BOOSTER 2G | USER GUIDE Technical Specifications 24/27 A TECHNICAL SPECIFICATIONS Dimensions 111 x 65 x 24 mm (4.4 x 2.6 x 1.0 in) Weight 120 gram (4.2 oz) Protection IP32 Approx. NEMA 2 Operating temperature -20°C … +85°C (-4°F … +140°F) Storage temperature -40°C … +85°C (-40°F … +140°F) Color Grey RAL 7016 / RAL 7040 Relative humidity 10% … 93% non-condensing Identification range Typically 10 meters (33 ft) line-of-sight required Battery, size AAA, 1.5V 2 x Duracell Procell PC2400 Or equivalent (IRmaxR < 8A, < 100VA)
BOOSTER 2G | USER GUIDE FCC / IC Statement 25/27 B FCC / IC STATEMENT Prox-Booster CGDBOOSTER4 and 1444A-BOOSTER4 Smartcard-Booster CGDBOOSTER5 and 1444A-BOOSTER5 Smartcard-Booster SB CGDBOOSTER7 and 1444A-BOOSTER7 Smartcard-Booster Ultimate CGDBOOSTER10 and 1444A-BOOSTER10 Compliance statements (part15.19) This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil se conforme aux normes CNR210 exemptés de licence du Industry Canada. L'opération est soumise aux deux conditions suivantes: (1) cet appareil ne doit causer aucune interférence, et (2) cet appareil doit accepter n'importe quelle interférence, y inclus interférence qui peut causer une opération non pas voulu de cet appareil. Warning (part15.21) Changes or modifications not expressly approved by party responsible for compliance could void the user’s authority to operate the equipment. This in particular is applicable for the antenna which can be delivered with the TRANSIT ULTIMATE System. RF Exposure (OET Bulletin 65) To comply with FCC RF exposure requirements for mobile transmitting devices, this transmitter should only be used or installed at locations where there is at least 20cm separation distance between the antenna and all persons. Information to the User (Part 15.106(b)) Note: This equipment has been tested and found to comply with the limits for a class B digital devices, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequent energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does not cause harmful interference to radio or television reception, which can be determine by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.
BOOSTER 2G | USER GUIDE Disclaimer 26/27 C DISCLAIMER This information is furnished for guidance, and with no guarantee as to its accuracy or completeness; its publication conveys no license under any patent or other right, nor does the publisher assume liability for any consequence of its use; specifica-tions and availability of goods mentioned in it are subject to change without notice; it is not to be reproduced in any way, in whole or in part, without the written consent of the publisher.
BOOSTER 2G | USER GUIDE Document revision 27/27 D DOCUMENT REVISION Version Date Comment 4.2 19-05-2015 Added Smartcard-Booster Ultimate 4.1 29-04-2014 HR update 4.0 13-02-2014 Layout adjusted to new corporate style.

Navigation menu