Neptune Technology Group BELTCLIP R900 Belt Clip Receiver User Manual 13 0249 Exhibit Cover

Download:
Mirror Download [FCC.gov]
Document ID	2138014
Application ID	tLAHDVeuqy+VRTeqFByGuQ==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	270kB (3375005 bits)
Date Submitted	2013-12-10 00:00:00
Date Available	2013-12-10 00:00:00
Creation Date	2013-12-02 10:00:31
Producing Software	ScanSoft PDF Create! 7
Document Lastmod	2013-12-02 10:21:31
Document Title	Microsoft Word - 13-0249- Exhibit Cover.doc
Document Creator	Microsoft Word - 13-0249- Exhibit Cover.doc
Document Author:	courtney.mcgann

Certification Exhibit
FCC ID: P2SBELTCLIP
IC: 4171B-BELTCLIP
FCC Rule Part: 15.249
IC Radio Standards Specification: RSS-210
ACS Project Number: 13-0249
Manufacturer: Neptune Technology Group, Inc.
Model: 13253-000
Manual
5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598
se
el
ea
tR
lo
Pi
Neptune Handheld System User’s Manual
se
el
ea
tR
lo
Pi
se
el
ea
tR
lo
Pi
Neptune Handheld System User’s Manual
Proprietary Rights Notice
This manual is an unpublished work and contains the trade secrets and confidential
information of Neptune Technology Group Inc., which are not to be divulged to third
parties and may not be reproduced or transmitted in whole or part, in any form or by
any means, electronic or mechanical for any purpose, without the express written
permission of Neptune Technology Group Inc. All rights to designs or inventions
disclosed herein, including the right to manufacture, are reserved to
Neptune Technology Group Inc.
The information contained in this document is subject to change without notice.
Neptune reserves the right to change the product specifications at any time without
incurring any obligations.
se
Trademarks Used in This Manual
el
ea
R900 is a registered trademark of Neptune Technology Group Inc. N_SIGHT R900
is a trademark of Neptune Technology Group Inc. R900 Belt Clip Receiver is a
trademark of Neptune Technology Group Inc. MRX920 is a trademark of
Neptune Technology Group Inc. ARB is a registered trademark of
Neptune Technology Group Inc.
Trimble Nomad s a registered trademark of Trimble Navigation Limited.
CE Net Windows, Windows 6.1, and Windows Mobile Device Center are registered
trademarks of Microsoft Corporation.
tR
Other brands or product names are the trademarks or registered trademarks of their
respective holders.
lo
FCC Conformity
Pi
CE5320B Handheld Computer
“NOTE: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.”
Warning: Changes or modifications to this device not expressly
approved by Neptune Technology Group Inc. could void the user's
authority to operate the equipment.
Trimble Nomad Handheld Computer
U.S.A.
This device complies with Part 15 of the FCC Rules. It is tested to comply with FCC
standards for home or office use. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
el
ea
se
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
tR
•
lo
R900 Belt Clip Receiver
Pi
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Neptune HR2650i
"NOTE: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help."
el
ea
se
•
Warning: Changes or modifications to this device not expressly
approved by Neptune Technology Group Inc., could void the user's
authority to operate the equipment.
tR
RF Exposure (Intentional Radiators Only)
This device has been tested and complies with FCC SAR (Specific Absorption Rate)
RF exposure compliance requirements for body-worn operation.
Pi
lo
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment is in direct contact with the body of the user
under normal operating conditions. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
Industry Canada
CE5320B Handheld Computer
This Class A digital apparatus meets all requirements of the Canadian Interference
Causing Equipment Regulations. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Cet appareillage numérique de la classe A répond à toutes les exigences de
l'interférence canadienne causant des règlements d'équipement. L'opération est
sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l'interférence
nocive, et (2) ce dispositif doit accepter n'importe quelle interférence reçue, y compris
l'interférence qui peut causer l'opération peu désirée.
Trimble Nomad
This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus as set out in the radio interference regulations of the Canadian
Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les
limites applicables aux appareils numériques de Classe B prescrites dans le règlement
sur le brouillage radioélectrique édicté par le Ministère des Communications du
Canada.
R900 Belt Clip Receiver
se
This Class B digital apparatus meets all requirements of the Canadian Interference
Causing Equipment Regulations. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
el
ea
Cet appareillage numérique de la classe B répond à toutes les exigences de
l'interférence canadienne causant des règlements d'équipement. L'opération est
sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l'interférence
nocive, et (2) ce dispositif doit accepter n'importe quelle interférence reçue, y compris
l'interférence qui peut causer l'opération peu désirée.
tR
Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication.
Pi
lo
Conformément à la réglementation d'Industrie Canada, cet émetteur radio ne peut
fonctionner à l'aide d'une antenne d'un type et maximum (ou moins) Gain approuvé
pour l'émetteur par Industrie Canada. Pour réduire le risque d'interférence avec
d'autres utilisateurs, le type d'antenne et son gain doivent être choisis afin que la
puissance isotrope rayonnée équivalente n'est pas plus que ce qui est nécessaire pour
une communication réussie.
Neptune HR2650i
This Class A digital apparatus meets all requirements of the Canadian Interference
Causing Equipment Regulations. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Cet appareillage numérique de la classe A répond à toutes les exigences de
l'interférence canadienne causant des règlements d'équipement. L'opération est
sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l'interférence
nocive, et (2) ce dispositif doit accepter n'importe quelle interférence reçue, y compris
l'interférence qui peut causer l'opération peu désirée.
CE Conformity
The CE5320B meets the 89/336/EEC directive intent for Electromagnetic Compatibility
Compliance when used with appropriate accessories. These are Class B products. In a
domestic environment, these products may cause radio interference, in which case, the
user may be required to take adequate measures.
The compliance was demonstrated to the following specifications as listed in the official
Journal of the European Communities:
EN 50081-2, Emissions
EN 50082-2, Immunity
EN 55022: Radiated, Class B
EN 61000-4-2: Electrostatic discharge
EN 55022: Conducted, Class B
EN 61000-4-3: RF radiated
se
EN 61000-4-4: Fast transients
lo
tR
el
ea
EN 61000-4-6: RF conducted
Neptune Technology Group Inc.
Literature No. UM Handheld System
11.13
Tallassee, AL 36078
Pi
Neptune Handheld System
User’s Manual
Part No. 11769-016
Copyright © 2005-2013
Neptune Technology Group Inc.
All Rights Reserved.
1600 Alabama Highway 229
Tel: (334) 283-6555
Fax: (334) 283-7293
Contents
Introduction
Conventions Used in this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Screen Shots Used in this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Differences in Screen Appearances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Product Support within the United States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Finding the Software Version Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
se
When Not Logged In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
When Logged On to N_SIGHT R900 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
el
ea
Contacting Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Finding Information within the Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Where to Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Meter Readers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Overview of the Neptune Handheld System
lo
tR
Operators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
Pi
Typical Meter Reading Process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Daily Use of the Neptune Handheld System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Meter Readers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Operators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Basic Features of the CE5320. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Operating Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Rain and Water Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Electromagnetic Resistance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Shock Resistance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
N_SIGHT R900 User’s Manual for the Neptune Handheld System
vii
Contents
Use of the CE5320 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Basic Features of the Nomad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Operating Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
Rain and Water Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
Electromagnetic Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Shock Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Use of the Nomad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
The Display on the Handhelds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
se
The Handheld Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
Menu Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15
el
ea
Data-Entry Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
Message Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
Navigating Through Screens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
tR
Icon Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19
Using the CE5320 Handheld
lo
Determining the System Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Local and Remote Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Pi
Unpacking and Inspecting Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Setting Up the CE5320. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
One CE5320 and a Communication Cradle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
The Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Connecting to the Host Computer and Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Connecting the Router, CE Handheld Cradle, and Power Supplies . . . . . . . . . . . . 3-5
Configuring the CE5320 Handheld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
On the Host Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
On the CE5320 Handheld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
viii
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Contents
The Display and Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Learning the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Function Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Number Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Direction Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Letter/Character Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Information Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
Quick Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
se
Adjusting System Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20
Calibrating the Stylus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20
Changing the Handheld Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22
el
ea
Working with the Properties Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22
Configuring RF/Serial Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24
Logging In and Out of the N_SIGHT R900 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26
Logging Into N_SIGHT R900 on the CE5320 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26
Using the Nomad Handheld
lo
tR
Logging Out of N_SIGHT R900 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30
Pi
Unpacking the Nomad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Setting Up the Nomad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
One Nomad and a Communication Cradle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
The Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Connecting to the Host Computer and Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Connecting the Router, Nomad Handheld Cradle, and Power Supplies. . . . . . . . . . 4-5
Configuring the Nomad Handheld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
On the Host Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
On the Nomad Handheld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
N_SIGHT R900 User’s Manual for the Neptune Handheld System
ix
Contents
The Display and Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Learning the Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Buttons and Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
Direction Buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
Number Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
Nomad Screen Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Changing the Size of the Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Large Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
se
Small Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
Lowercase Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
el
ea
Uppercase Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
Numeric and Symbols Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
Information Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
Direction Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18
tR
Combination Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19
Adjusting System Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22
Calibrating the Stylus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23
lo
Changing the Handheld Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26
Working with the Properties Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26
Pi
Configuring RF/Serial Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28
Turning On and Off the Nomad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30
Turning the Nomad On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30
Turning the Nomad Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30
Logging In and Out of the N_SIGHT R900. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-31
Logging Into N_SIGHT R900 on the Nomad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-31
Logging Out of N_SIGHT R900 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-36
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Contents
Setting Up the R900 Belt Clip Receiver
R900 Belt Clip Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
R900 Belt Clip Receiver Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Nomad Handheld and R900 Belt Clip Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Unpacking and Inspecting Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
R900 Belt Clip Receiver Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Using the R900 Belt Clip Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
se
Understanding the R900 Belt Clip Receiver Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Accessing the R900 Belt Clip Receiver Status Screen . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
Understanding the R900 Belt Clip Receiver LED Operating Modes . . . . . . . . . . . . . . . . 5-8
el
ea
Understanding the External Battery Charger Status . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
Pairing the Trimble Nomad to the R900 Belt Clip Receiver through the Bluetooth . . . . 5-10
Pairing the Trimble Nomad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
Using the R900 Belt Clip Receiver to Read a Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
tR
R900 Belt Clip Receiver Status Screen in N_SIGHT R900 . . . . . . . . . . . . . . . . . . . . . . 5-11
RF Performance Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
Selecting the R900 Belt Clip Receiver Reading Mode . . . . . . . . . . . . . . . . . . . . . . 5-13
lo
Using the R900 Belt Clip Receiver RF Test Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
Pi
From the Login Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
From the Route Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
R900 Belt Clip Receiver SD Card Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
Updating R900 Belt Clip Receiver Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15
How the Firmware Update Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16
N_SIGHT R900 User’s Manual for the Neptune Handheld System
xi
Contents
Gathering Route Data
The Reading Entry Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Manually Collecting Meter Readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Entering a Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Entering a Skip Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
Entering Comment Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Adding Free-Form Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
se
Leaving a Reading Blank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
Collecting RR Readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
Collecting an RF Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13
el
ea
Working with Accounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14
Changing the Route Direction, Forward or Reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14
Tagging an Account . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-15
Finding Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-17
tR
Validating Readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-20
Hi/Low Fails. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-20
lo
Removing a Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-22
Clearing a Skip Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-24
Pi
Clearing a Comment Code, Customer Note, or Trouble Code. . . . . . . . . . . . . . . . . . . . . . . 6-26
Adding a New Meter to a Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-27
Correcting or Changing Meter Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-29
Finding and Displaying Reading-Entry Screens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-31
Moving Through Reading Entry Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-32
Reviewing Additional Information for an Account . . . . . . . . . . . . . . . . . . . . . . . . . 6-32
Location or Hazard Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-32
Statistics for Loaded Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-34
Moving Around Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-35
xii
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Contents
Resequencing Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-37
Resequence an Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-37
Resequence While Collecting Readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-39
Confirming the Resequencing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-39
Communicating with the Host Computer
Exchanging Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
se
Exiting the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Using the Field Programmer
el
ea
Sending and Receiving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
Connecting the Mouse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
tR
Connecting the Mouse to the CE5320 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
Connecting the Mouse to the Nomad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4
Verifying the Handheld Recognizes the Mouse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6
lo
Starting Field Programmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6
Pi
Changing Your Password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
Programming the ProRead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Conguring the ProRead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Querying the ProRead. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14
Reading the ProRead Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15
Viewing Software and Firmware Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17
Programming the R900G Endpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18
Configuring Gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18
Collecting the Initial Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19
Querying the R900G Endpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21
N_SIGHT R900 User’s Manual for the Neptune Handheld System
xiii
Contents
Using Command Gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-23
Reading the R900G Endpoint Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-24
Viewing Software and Firmware Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-25
Networking Two Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-26
Programming Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-26
Programming the Network Primary Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-26
Programming the Network Secondary Register. . . . . . . . . . . . . . . . . . . . . . . . . . . 8-27
Network Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-27
se
Wiring the Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-28
Managing Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-28
el
ea
Managing Formats for ProRead Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-28
Selecting ProRead Preferences. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-29
Selecting a ProRead Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-31
Editing a ProRead Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-32
Using the New ProRead Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-34
tR
Deleting a Format for ProRead Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-34
Creating a New ProRead Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-35
Using the Custom Format Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-37
lo
Saving the Custom ProRead Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-39
Pi
Creating Formats for R900G Endpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-39
Configuring Gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-40
Selecting a Gas Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-41
Adding or Editing a Gas Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-43
Using the Gas Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-48
Deleting a Format for R900G Endpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-48
xiv
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Contents
Maintaining and Repairing the Neptune Handheld System
Recommended Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
Maintaining the CE5320 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
Cleaning the CE5320 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
Storing the CE5320 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2
Short-term Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2
Long-term Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2
se
Checking the Battery Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Transporting the CE5320 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4
Repairing the CE5320 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4
el
ea
Recharging the Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5
Calibrating the CE5320 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5
Replacing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Removing or Replacing the Handstrap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11
tR
Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11
Replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13
lo
Maintaining the Nomad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-14
Pi
Battery Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-14
Tips for Extending the Battery Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-14
Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-15
Checking the Battery Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-15
Replacing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-16
Calibrating the Nomad Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-17
Notification LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-18
Maintaining the R900 Belt Clip Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-19
Recommended Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-19
Battery Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-19
Tips for Extending the Battery Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-20
N_SIGHT R900 User’s Manual for the Neptune Handheld System
xv
Contents
Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-20
Using the USB Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-20
Charging Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-21
Using the Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-22
Replacing the R900 Belt Clip Receiver Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-23
Removing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-23
Replacing the Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-24
LED Status Indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-25
se
Checking the Battery Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-26
Recommended Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-26
Ordering Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-26
el
ea
CE5320 Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-26
Nomad Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-26
R900 Belt Clip Receiver Spare Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-27
Troubleshooting
lo
10
tR
Returning your Neptune Handheld System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-28
Troubleshooting the Handheld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
Pi
Basic Tasks for the CE5320B Handheld. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2
Basic Tasks for the Nomad Handheld. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4
Reading-Entry Tasks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5
Communication Tasks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6
Starting the N_SIGHT R900 Program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6
Loading Data Initially. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6
Missing Route Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7
Resetting the CE5320B
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7
Rebooting the CE5320B
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-9
Rebooting When Logged into a Route in N_SIGHT R900. . . . . . . . . . . . . . . . . . . 10-9
Rebooting When Logged off N_SIGHT R900 . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11
xvi
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Contents
Appendix A
Changing Volume Settings 1
Adjusting Customized Sounds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1
Changing the Volume Setting on the CE5320 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1
Changing the Volume Setting on the Nomad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-5
Tokens List for Custom Format Screen 1
Appendix C
Pressure Configuration Factor Indexes 1
el
ea
se
Appendix B
Pi
Index
lo
Glossary
tR
Available Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-1
N_SIGHT R900 User’s Manual for the Neptune Handheld System
xvii
Contents
Pi
lo
tR
el
ea
se
Notes:
xviii
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Figures
Page
tR
el
ea
se
Sample Screens on the Neptune Handheld System . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Login Screens on the Neptune Handheld System . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Screen Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Typical Meter Reading Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
CE5320B Handheld Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Back of CE5320 Handheld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Nomad Handheld Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Back of Nomad Handheld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
Menu and Data-Entry Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
Message Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15
Meter Position within Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
Navigating Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
Search Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20
GoTo Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
Cradle and Charging Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Cradle, Router, and Cables Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Connecting RJ-45 Ethernet Cable to Router, Port 1 . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Connecting the Power Cable to the Communications Cradle . . . . . . . . . . . . . . . . . 3-6
Connecting the Ethernet RJ-45 Cable to the Cradle . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Network Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Connecting Multiple Handheld Cradles to Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
N_SIGHT R900 Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
N_SIGHT R900 Admin Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Learning the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
N_SIGHT R900 Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21
N_SIGHT R900 Stylus Calibration Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21
Stylus at Another Location on Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22
Handheld Properties Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
N_SIGHT R900 F1 Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25
N_SIGHT R900 System Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25
lo
1.1
1.2
1.3
1.4
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
3.12
3.13
3.14
3.15
3.16
Title
Pi
Figure
N_SIGHT R900 User’s Manual for the Neptune Handheld System
xix
Figures
xx
Page
tR
el
ea
se
RF/Serial Properties Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26
N_SIGHT R900 Message Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-27
N_SIGHT R900 Clock Error Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-27
N_SIGHT R900 Set Date / Time Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28
N_SIGHT R900 Handheld Login Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28
N_SIGHT R900 Select Route Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-29
N_SIGHT R900 Initializing Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-29
N_SIGHT R900 Reading Entry Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30
Nomad and Cradle Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Connecting RJ-45 Ethernet Cable to Router, Port 1 . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Nomad Communications Cradle Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Network Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
N_SIGHT R900 Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
N_SIGHT R900 Admin Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Learning the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Nomad Large Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
Nomad Small Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
Nomad Lowercase Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
Nomad Uppercase Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
Nomad Numeric and Symbols Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
N_SIGHT R900 Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23
N_SIGHT R900 Stylus Calibration Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24
Stylus at Another Location on Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25
Handheld Properties Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26
N_SIGHT R900 F1 Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28
N_SIGHT R900 System Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29
RF/Serial Properties Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29
N_SIGHT R900 Message Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-32
N_SIGHT R900 Clock Error Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-33
N_SIGHT R900 Set Date / Time Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-33
N_SIGHT R900 Handheld Login Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34
N_SIGHT R900 Select Route Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35
lo
3.17
3.18
3.19
3.20
3.21
3.22
3.23
3.24
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
4.11
4.12
4.13
4.14
4.15
4.16
4.17
4.18
4.19
4.20
4.21
4.22
4.23
4.24
Title
Pi
Figure
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Figures
Page
tR
el
ea
se
N_SIGHT R900 Initializing Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35
N_SIGHT R900 Reading Entry Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-36
Meter Reading Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
R900 Belt Clip Receiver Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
R900 Belt Clip Receiver Status Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
R900 Belt Clip Receiver RF Mode Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
R900 BCR RF Mode Screen from Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
Tab within N_SIGHT R900 Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15
R900 Belt Clip Receiver Firmware Tab with Update Options . . . . . . . . . . . . . . . . 5-16
N_SIGHT R900 Reading Entry Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
N_SIGHT R900 Reading Entry Field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
N_SIGHT R900 Skip Order Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
N_SIGHT R900 Skip Order Reason Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
N_SIGHT R900 Skipped Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
N_SIGHT R900 Coded Notes Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Drop-down Selection List of Coded Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
N_SIGHT R900 Comment Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
Viewing Comment Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
N_SIGHT R900 Free Form Notes Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
Leaving a Meter Reading Blank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
N_SIGHT R900 Manual Reading Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
N_SIGHT R900 RF Reading Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13
Left to Right Route Direction Icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14
Right to Left Route Direction Icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-15
Tag Account Icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16
Tagged Account . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16
N_SIGHT R900 Find Order Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-17
Search Display Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18
Search Screen Enter Multiple Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18
Search Screen Multiple Values to Match . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-19
Reading Outside High/Low Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-20
N_SIGHT R900 Hi / Lo / No / Inact Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-21
lo
4.25
4.26
5.1
5.2
5.3
5.4
5.5
5.6
5.7
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
6.11
6.12
6.13
6.14
6.15
6.16
6.17
6.18
6.19
6.20
6.21
6.22
6.23
Title
Pi
Figure
N_SIGHT R900 User’s Manual for the Neptune Handheld System
xxi
Figures
xxii
Page
tR
el
ea
se
Reading to be Cleared . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-22
N_SIGHT R900 Reset Order Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-23
Reset Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-23
Reading to be Unskipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-24
N_SIGHT R900 Undo Skipped Order Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-25
Reading Field after Unskipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-25
Screen Showing Code Attached . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-26
Screen Where Code Was Entered . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-27
N_SIGHT R900 Meter Process Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-28
N_SIGHT R900 New Meter Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-28
Meter Information to Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-29
N_SIGHT R900 Meter Process Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-30
N_SIGHT R900 Change Meter Info Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-30
Additional Meter Information to View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-33
Location and Hazard Codes Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-33
For Statistics for Loaded Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-34
Statistics for Loaded Routes Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-35
N_SIGHT R900 GoTo Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-36
Account to Resequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-37
Resequence Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-38
Inline Resequencing Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-39
Confirm Resequencing Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-40
Confirm Resequencing Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
N_SIGHT R900 Handheld Logout Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Hold Routes Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
N_SIGHT R900 Login Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
Synchronize Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
Field Programmer Mouse for the CE5320 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
Connecting Mouse to CE5320 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
Field Programmer Mouse for the Nomad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4
Connecting Mouse to Nomad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5
Field Programmer Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
lo
6.24
6.25
6.26
6.27
6.28
6.29
6.30
6.31
6.32
6.33
6.34
6.35
6.36
6.37
6.38
6.39
6.40
6.41
6.42
6.43
6.44
6.45
7.1
7.2
7.3
7.4
7.5
8.1
8.2
8.3
8.4
8.5
Title
Pi
Figure
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Figures
Page
tR
el
ea
se
Field Programmer Password Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
Change Password Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
ProRead Configuration Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10
Format Name Selection List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10
Otr Selection List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11
Program Result -- Pass Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12
ProRead Program Details Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13
ProRead Query Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14
ProRead Query Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15
ProRead Read Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16
ProRead Reading Result Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16
ProRead Software and Firmware Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17
Gas Meter Configuration Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18
Gas Program Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19
Format Name Selection List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19
Program Result – Sending Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20
Program Result – Pass Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20
Gas Query Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21
Gas Query Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-22
Command Gas Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-23
Gas Read Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-24
Gas Reading Result Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-25
Gas Software and Firmware Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-26
Field Programmer Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-29
ProRead Preferences Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-30
Select Formats Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-31
ProRead New Format Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-32
Default ProRead New Format Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-35
New Button Available . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-36
Custom Format 1 Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-37
Custom Format 2 Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-38
Configure Gas Password Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-40
lo
8.6
8.7
8.8
8.9
8.10
8.11
8.12
8.13
8.14
8.15
8.16
8.17
8.18
8.19
8.20
8.21
8.22
8.23
8.24
8.25
8.26
8.27
8.28
8.29
8.30
8.31
8.32
8.33
8.34
8.35
8.36
8.37
Title
Pi
Figure
N_SIGHT R900 User’s Manual for the Neptune Handheld System
xxiii
Figures
xxiv
Page
tR
el
ea
se
Gas New Format Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-41
Gas New Format Selection List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-43
Gas Values Shown on New Format Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-44
Gas New Format Screen – Blank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-47
Battery Status Indicator on CE5320 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Handheld Battery Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6
N_SIGHT R900 Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
N_SIGHT R900 Admin Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
N_SIGHT R900 Calibrate Battery Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
Remove the Captive Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Inserting the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
Removing Screw From Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11
Removing the Captive Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-12
Opening the Velcro Closure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13
Battery Status Indicator on Nomad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-15
Changing the Nomad Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-16
External Battery Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-22
R900 Belt Clip Receiver Side View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-23
Latch Direction to Open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-23
Battery Inside Compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-24
R900 Belt Clip Receiver Battery Inside Compartment . . . . . . . . . . . . . . . . . . . . . . 9-25
N_SIGHT R900 Login Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7
N_SIGHT R900 Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-8
N_SIGHT R900 Admin Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-8
Reset Warning Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-9
N_SIGHT R900 F1 Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10
N_SIGHT R900 Handheld Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10
Reboot Handheld Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11
N_SIGHT R900 Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
N_SIGHT R900 Admin Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
CE.Net Windows Explorer Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Windows CE Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
lo
8.38
8.39
8.40
8.41
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
9.9
9.10
9.11
9.12
9.13
9.14
9.15
9.16
9.17
10.1
10.2
10.3
10.4
10.5
10.6
10.7
A.1
A.2
A.3
A.4
Title
Pi
Figure
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Figures
Figure
Page
Selecting Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
Windows Control Panel Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
Volume & Sounds Properties Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
Nomad Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-6
Nomad Scrollbar and Radio Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-6
Pi
lo
tR
el
ea
se
A.5
A.6
A.7
A.8
A.9
Title
N_SIGHT R900 User’s Manual for the Neptune Handheld System
xxv
Figures
Pi
lo
tR
el
ea
se
Notes:
xxvi
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Tables
Page
el
ea
se
N_SIGHT R900 Display Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19
Nomad Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20
R900 Belt Clip Receiver Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
R900 Belt Clip Receiver Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
R900 Belt Clip Receiver Software Functions . . . . . . . . . . . . . . . . . . . . . . . . 5-7
R900 Belt Clip Receiver LED Operating Modes . . . . . . . . . . . . . . . . . . . . . . 5-8
External Battery Charger LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
Meter Input Drive Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-45
Calibration Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-18
Calibration Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-18
Charging Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-21
LED Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-25
CE5320 Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-26
Nomad Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-27
R900 Belt Clip Receiver Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-27
Custom Format Tokens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Pressure Configuration Factor Index Table . . . . . . . . . . . . . . . . . . . . . . . . C-1
Pi
lo
2.1
4.1
5.1
5.2
5.3
5.4
5.5
7.6
9.1
9.2
8.3
9.4
8.5
9.6
8.7
B.1
C.1
Title
tR
Table
N_SIGHT R900 User’s Manual for the Neptune Handheld System
xxvii
Tables
Pi
lo
tR
el
ea
se
Notes:
xxviii
N_SIGHT R900 User’s Manual for the Neptune Handheld System
1 Introduction
el
ea
se
The Neptune Handheld System User’s Manual describes how to use the
following components of the Neptune handheld system to collect route
data. It also explains how to exchange route and account data with the
host computer for the N_SIGHT™ R900® host software. Descriptions
for the following devices and procedures for using them are included in
this manual.
CE5320 Handheld (CE5320)
•
Trimble® Nomad® (Nomad)
•
Neptune Field Programmer
•
tR
•
R900® Belt Clip Receiver (BCR)
lo
This manual also describes how to maintain these devices, also referred
to as the Neptune handheld system.
Pi
Conventions Used in this Manual
This manual uses the following icons and typographic conventions to
identify special information.
The Warning icon identifies actions that can injure the user or
permanently damage the product.
The Caution icon identifies important information that is critical to
successfully operating N_SIGHT R900.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
1-1
Introduction
The Note icon identifies information that clarifies a point within
the text.
The Setup icon identifies a part of the application program that
needs only periodic adjustment.
The Meter Reader icon identifies tasks that are usually
performed by a meter reader.
se
The Operator icon identifies tasks that are usually performed by
a N_SIGHT R900 operator.
Save data
Messages that appear in the display of the handheld are in
Courier type.
Keyboard entries are in Courier bold type.
el
ea
Admin
Save As
Menu titles and menu selections shown in the display of the
handheld are in bold type.
Keys that appear on the face of the handheld are in SMALL CAPS.
tR
enter
Screen Shots Used in this Manual
Pi
lo
In order to be consistent with the representation of all the screens
in this manual. the screens used in this guide are captured on the
Nomad. However, they appear very similarly on the other
handheld device.
Except for the chapter dedicated to setting up and using the CE5320B, this
manual uses the Nomad screens. However, the CE5320B screens are very
similar.
Differences in Screen Appearances
The most predominant differences in the appearances of the screens on
both handheld devices are the following.
1-2
•
CE5320 screens appear in a landscape or horizontal format.
•
The Nomad screens appear in a portrait or vertical format.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Introduction
Figure 1.1 demonstrates the differences in the screen appearances.
Sample Nomad Handheld Screen
Version
Number
el
ea
se
Sample CE5320 Screen
Version
Number
tR
Figure 1.1 Sample Screens on the Neptune Handheld System
lo
Although the style of the screens appear differently, the information on
both the CE5320B and the Nomad screens is identical.
Pi
Product Support within the United States
Neptune offers you different ways to obtain high-quality, responsive
technical support. However, before contacting Neptune, it is important
that you know the version number of the software that your handheld
uses. This information is useful to the support technician who helps you.
Finding the Software Version Number
The procedures for finding the software version number differ
depending on whether or you have logged on to N_SIGHT R900.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
1-3
Introduction
When Not Logged In
If you have not yet logged on to N_SIGHT R900, complete the
following.
Turn ON the handheld.
The handheld initializes N_SIGHT R900, and this process can take
a few minutes.
Go to the Login screen.
Version
Number
Pi
lo
tR
el
ea
se
The Login screen displays the version number at the bottom of the
screen as shown in Figure 1.3.
Figure 1.2 Login Screens on the Neptune Handheld System
When Logged On to N_SIGHT R900
When you have logged on to N_SIGHT R900, you can find the version
number by completing the following from any screen.
•
From any N_SIGHT R900 screen, press Ctrl + I.
The Screen Information appears as shown in Figure 1.3.
1-4
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Introduction
el
ea
se
Version
Number
•
tR
Figure 1.3 Screen Information
View the version number which appears directly below the
handheld ID on this screen.
Pi
lo
This screen contains all the vital information you need to know
about the handheld.
Contacting Customer Support
Within North America, Neptune Customer Support is available Monday
through Friday, 8:00 AM to 7:00 PM Eastern Standard Time by
telephone, email, or fax.
To contact Customer Support by phone, call (800) 647-4832. You will
be directed to the appropriate team of specialists. These specialists are
dedicated to assisting you until the issue is resolved to your satisfaction.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
1-5
Introduction
When placing a call, be prepared to give the following information:
•
The exact wording of any message that appears on the screen of the
computer or the handheld device
•
A description of what happened and what you were doing when the
problem occurred
•
A description of how you tried to solve the problem
•
Your utility’s name
Figure 1.4 Customer Support
Pi
lo
tR
el
ea
se
You will be directed according to the options shown in Figure 1.4.
To contact Customer Support by fax, send a description of your problem
to (334) 283-7497. Please include on the fax cover sheet the best time of
day for a Customer Support Specialist to contact you.
To contact Customer Support by e-mail, send your information to
hhsupp@neptunetg.com.
1-6
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Introduction
Finding Information within the Manual
This manual is written for two basic types of users: meter readers and
operators. To help both types of users find the information they need,
this manual uses the following symbols to identify different types of
tasks:
Tasks usually performed by meter readers are indicated by the
icon.
Meter Reader
•
Tasks usually performed by N_SIGHT R900 operators are
indicated by the Operator
icon.
•
Tasks that are performed occasionally are indicated by the Setup
icon.
el
ea
se
•
In addition to looking for these symbols, use the following sections to
find information quickly:
If you have a specific task or item in mind, look in the Index.
•
Look through the Contents to find tasks and topics whose titles are
not familiar to you.
Pi
Where to Start
If you are unsure of a term, look it up in the Glossary.
lo
•
tR
•
The best way for you to use this manual depends upon your
responsibilities in your company’s meter reading process and how
familiar you are with using a handheld computer.
•
Meter readers typically gather meter readings and other
information about meters on a route. They most likely use the
Neptune handheld system to gather meter readings and route data
and to get route assignments.
•
Operators typically manage the daily tasks of a meter reading
process. They most likely use a one of the Neptune handheld
devices to upload route data from it to their computer and to
download billing and customer information from their computer to
the handheld device.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
1-7
Introduction
Meter Readers
If this is the first time that you have used the handheld, read one of the
following chapters to get a general understanding of how the display
and keys work.
You will probably find the following chapters of the manual most
useful.
Chapter 2, "Overview of the Neptune Handheld System" describes
the basic features and functions of the handhelds; introduces you to
the Nomad handheld computer; how the handheld is incorporated
into the Neptune handheld system host software; and how it is used
by both meter readers and operators.
•
Chapter 3, "Using the CE5320 Handheld" provides help to set up
and get started with your CE5320 handheld so that you can begin
collecting information from the field and exchanging information
with the host computer.
•
Chapter 4, "Using the Nomad Handheld" provides help to set up
and get started with your Nomad handheld so that you can begin
collecting information from the field and exchanging information
with the host computer.
tR
el
ea
se
•
Chapter 5, "Setting Up the R900 Belt Clip Receiver" provides basic
instructions for unpacking and inspecting the Belt Clip. It also gives
instructions for setting it up and becoming familiar with the display,
pairing it with the handheld, and usage.
Pi
lo
•
1-8
•
Chapter 6, "Gathering Route Data" provides instructions for using
the handheld device to collect meter readings and route data.
•
Chapter 7, "Communicating with the Host Computer" provides
procedures for exchanging information with the host computer and
exiting the software.
•
Chapter 8, "Using the Field Programmer" provides fundamental
instructions for operating the Field Programmer including how to
connect the mouse, programming the device, and operating the
Field Programmer.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Introduction
Chapter 10, "Troubleshooting" helps you solve any issues or
problems that can occur when using the Neptune handheld system.
•
Appendix A, "Changing Volume Settings" provides instructions for
adjusting customized sounds and the volume control setting.
•
Appendix B, "Tokens List for Custom Format Screen" provides a
list of the tokens that are constants and special characters used with
the Field Programmer as part of a ProRead™ format.
•
Appendix C, "Pressure Configuration Factor Indexes" provides a
list used for selecting gas formats available from American Meter,
Sensus, and Actaris when using the Field Programmer.
•
"Glossary" provides a list of terms used in this manual that can be
useful when reading and learning how to use the handheld device
and software.
el
ea
se
•
Operators
Chapter 3, "Using the CE5320 Handheld" provides help to set up
and get started with your CE5320 handheld so that you can begin
collecting information from the field and exchanging information
with the host computer.
Pi
lo
•
tR
If this is the first time that you have used the CE5320, read Chapter 2,
"Overview of the Neptune Handheld System" to get a general
understanding of how the display and keys work. You will probably find
the following chapters of the manual most useful.
•
Chapter 4, "Using the Nomad Handheld" provides help to set up
and get started with your Nomad handheld so that you can begin
collecting information from the field and exchanging information
with the host computer.
•
Chapter 5, "Setting Up the R900 Belt Clip Receiver" provides basic
instructions for unpacking and inspecting the R900 BCR. It also
gives instructions for setting it up and becoming familiar with the
display, pairing it with the handheld, and usage.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
1-9
Introduction
Chapter 7, "Communicating with the Host Computer" provides
procedures for exchanging information with the host computer and
exiting the software.
•
Chapter 9, "Maintaining and Repairing the Neptune Handheld
System" provides instructions for maintaining and repairing the
CE5320, the Nomad, and the R900 BCR and includes
recommended spare parts. It also gives instructions for packing and
shipping a device to Neptune should you ever need to return any
unit for repair.
•
Chapter 10, "Troubleshooting" helps you to solve any issues or
problems that can occur when using the Neptune handheld system.
•
Appendix A, "Changing Volume Settings" provides instructions for
adjusting customized sounds and the volume control setting.
•
"Glossary" provides a list of terms used in this manual that can be
useful when reading and learning how to use the handheld device
and software.
Pi
lo
tR
el
ea
se
•
1-10
N_SIGHT R900 User’s Manual for the Neptune Handheld System
2 Overview of the Neptune Handheld System
Typical Meter Reading Process
el
ea
se
This chapter is designed to introduce you to the Neptune handheld
system handheld computer. It will explain how the handheld is
incorporated into the N_SIGHT R900 host software, and how it will be
used by both meter readers and operators. It will also help you become
familiar with the basic features and functions the handheld computer
offers.
tR
By using the handheld computer in conjunction with N_SIGHT R900
software, the meter reading process has an effective tool in collecting
and distributing information that is critical to managing daily tasks.
Pi
lo
Meter readers use the handheld to gather route information. Operators
use N_SIGHT R900 to collect route information from the handheld and
to collect billing information from the billing computer. Once this
information is stored on an operator’s computer, called the host
computer, operators use N_SIGHT R900 to make route assignments and
to send updated information to the handheld and to the billing computer.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
2-1
Overview of the Neptune Handheld System
7. Post meter readings and route
data to customer accounts for
billing.
1. Transfer billing information to
the host computer.
6. Transfer files containing
meter readings and route
data to the billing computer.
el
ea
3. Load routes onto meter
reading devices.
se
2. Assign routes to meter readers.
5.
4. Collect meter readings and route
tR
data using a handheld computer.
Upload meter readings and
route data from the handheld
computers to a host
computer.
lo
Figure 2.1 Typical Meter Reading Process
Pi
Daily Use of the Neptune Handheld System
Because the Neptune handheld system helps users collect and pass on
different types of information needed by a meter reading process, how
you use it depends upon your responsibilities in your meter reading
process. The following topics describe how meter readers and operators
typically use the handheld to complete their work.
2-2
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Overview of the Neptune Handheld System
Meter Readers
se
During a typical day, meter readers use the handheld to get route
assignments and to gather route data. Meter readers pick up a handheld
in the morning and review route assignments that were downloaded the
previous afternoon by an operator. Then, they use it to gather meter
readings and other data from the assigned routes. After they complete
their routes, meter readers return the handheld to the office where an
operator uploads the readings and route data onto the computer and then
downloads route assignments and other data to it.
Operators
el
ea
Typically, operators connect the handheld so that it can communicate
with their computer. Once the handheld is connected, operators set up
the software so that it can exchange information with their computer,
called the host computer.
lo
tR
During a typical day, operators make route assignments and collect
billing information from the billing computer. Toward the end of the
day, after meter readers complete their routes and return the handhelds
to the office, operators exchange information with them. During a
typical information exchange, route data is unloaded from the handheld
at the same time that the next day’s assignments and updated billing
information are loaded to it.
Pi
The operator makes sure that the handheld is fully charged and ready for
use by a meter reader.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
2-3
Overview of the Neptune Handheld System
Basic Features of the CE5320
In addition to an environmental seal that protects the unit from dust, dirt,
and water, the CE5320 includes the following features:
Keyboard functions
Display
se
Alphanumeric keys
Editing functions
Blue key
Special characters
Battery status light
Pi
lo
tR
el
ea
Keyboard
Figure 2.2 CE5320B Handheld Features
2-4
•
Display—shows up to 33 lines of text and allows touch-screen
entry. In addition, you have the option of backlighting the display
so that information is visible in low light.
•
Keyboard—uses 51 multifunctional keys that include letter,
number, character, task, and menu keys. The tactile design of the
keys and the tone that sounds when a key is pressed help to reduce
errors. In addition, if you have the Keyboard Backlight option, the
keys can be illuminated making them easy to read in low light.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Overview of the Neptune Handheld System
•
Ethernet Communication Port—an RJ-45 Ethernet connector on
the cradle allows you to connect the CE5320 using an RJ-45
Ethernet cable to a variety of devices. This capability provides for
route assignments and route data to be sent to the CE5320, and
meter readings and route information to be retrieved from it.
•
Battery Status Light—lets you know when the battery is fully
charged. If the light is red, the battery needs recharging and if the
light is green, the battery is charged and the handheld is operational.
Pi
lo
tR
el
ea
se
Do not attempt to remove the back panel of the CE5320. Attempting to
repair the unit on your own voids the warranty by breaking the warranty
label which covers a screw on the back of the unit. If the CE5320 does
not function, contact a Neptune support technician for assistance. For
help in contacting Neptune, refer to the topic “Contacting Customer
Support,” on page 1-5.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
2-5
Overview of the Neptune Handheld System
Cover
Stylus
se
Handstrap
Pi
lo
tR
el
ea
Battery
compartment
2-6
Battery recharge
contacts
Figure 2.3 Back of CE5320 Handheld
•
Handstrap—makes it easy to carry the CE5320.
•
Stylus—allows for ease of use for the touch screen on the CE5320.
•
Battery Compartment—holds a lithium-ion battery pack that is
rated for a usage up to 500 charge cycles or 2 years - whichever
occurs first.
•
Battery Recharge Contacts—recharges the battery when the
CE5320 rests in a communication cradle.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Overview of the Neptune Handheld System
The CE5320 also offers the following:
Suspend Mode—puts the CE5320B into a low-power state.
•
Manual Off Feature—allows operators to turn the CE5320 off
immediately.
•
Automatic Return Feature—shows the information that was last
in the display after the handheld is turned off manually or
automatically.
•
Customized Sounds—can be used as warning signals or as a
prompt.
se
•
Operating Environment
el
ea
Long exposure to temperatures below -20°C (-4°F) can damage the display.
Prolonged exposure to temperatures above 50°C (122°F) will damage the
battery and above 60°C (140°F) can permanently damage the unit.
tR
The recommended temperature range for operating the CE5320 is from
-20°C to +50°C (-4°F to +122°F). Short exposure to temperatures lower
or higher than these can cause the display to turn very dark or very light
until the unit returns to the recommended operating temperature range.
lo
Rain and Water Resistance
Pi
Water resistance can be impaired if the door of the battery compartment or top
cover is improperly closed or if the gaskets have deteriorated.
The handheld withstands exposure to rain without allowing water to
seep inside the unit. It is designed to endure occasional immersions, and
the unit floats making it easy to retrieve if dropped in water.
Electromagnetic Resistance
The CE5320 performs well in most common environments where
electromagnetic fields are present. Examples of these environments
include areas near power-transmission lines, electric motors,
transformers, compressors, and low-power radio transmitters.
Performance can be degraded when using a communication cable, a
peripheral, such as a printer, or a battery charger under these conditions.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
2-7
Overview of the Neptune Handheld System
Shock Resistance
When the unit is operated within the specified temperature range, it can
withstand occasional drops from up to two meters (six feet) onto a hard
surface.
Use of the CE5320
Pi
lo
tR
el
ea
se
To set up and begin using your CE5320 handheld, go to “Using the
CE5320 Handheld,” on page 3-1.
2-8
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Overview of the Neptune Handheld System
Basic Features of the Nomad
In addition to an environmental seal that protects the unit from dust, dirt,
and water, the Nomad includes the following features.
Charging LED
se
Notification LED
Display
el
ea
Battery status indicator
Keyboard
tR
Left application soft key
Start
Function key
Pi
Power
lo
Tab
Right application soft key
OK
Backspace
Today
Enter
Arrow keys (used with
function key)
Figure 2.4 Nomad Handheld Features
•
Display—shows up to 33 lines of text and allows touch-screen
entry. In addition, you have the option of backlighting the display
so that information is visible in low light.
•
Keyboard—uses 51 multifunctional keys that include letter,
number, character, task, and menu keys. The tactile design of the
keys and the tone that sounds when a key is pressed help to reduce
N_SIGHT R900 User’s Manual for the Neptune Handheld System
2-9
Overview of the Neptune Handheld System
errors. In addition, if you have the Keyboard Backlight option, the
keys can be illuminated making them easy to read in low light.
Ethernet Communication Port—an RJ-45 Ethernet connector on
the cradle allows you to connect the Nomad using an Ethernet cable
to a variety of devices. This capability provides for route
assignments and route data to be sent to the Nomad, and meter
readings and route information to be retrieved from it.
•
Battery Status Light—lets you know when the battery is fully
charged. If the light is red, the battery needs recharging and if the
light is green, the battery is charged and the handheld is operational.
se
•
Pi
lo
tR
el
ea
Do not attempt to remove the back panel of the Nomad. Attempting to
repair the unit on your own voids the warranty by breaking the warranty
label which covers a screw on the back of the unit. If the Nomad does
not function, contact a Neptune support technician for assistance. For
help in contacting Neptune, refer to the topic “Contacting Customer
Support,” on page 1-5.
2-10
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Overview of the Neptune Handheld System
Handstrap
Stylus
Battery door screws
Pi
lo
tR
el
ea
se
Battery
compartment
Figure 2.5 Back of Nomad Handheld
•
Handstrap—makes it easy to carry the Nomad.
•
Battery Compartment—holds a lithium-ion battery pack that is
rated for up to 500 charge cycles or 2 years - whichever occurs first.
•
Stylus—makes is easy to use the touchscreen display. Can be
calibrated for the user’s own personal touch.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
2-11
Overview of the Neptune Handheld System
The Nomad also offers the following:
Suspend Mode—puts the Nomad into a low-power state.
•
Manual Off Feature—allows operators to turn the Nomad off
immediately.
•
Automatic Return Feature—shows the information that was last
in the display after the handheld is turned off manually or
automatically.
•
Customized Sounds—can be used as warning signals or as a
prompt.
se
•
el
ea
Operating Environment
tR
The Trimble Nomad has gone through multiple tests and meets MIL-STD-810F
military standards. Long exposure to temperatures below -20°C (-4°F) can
damage the display. Prolonged exposure to temperatures above 50°C (122°F)
will damage the battery and above 60°C (140°F) can permanently damage the
unit.
lo
The recommended temperature range for operating the Nomad is from -30C to 60C (-22F to 140F). Short exposure to temperatures lower or
higher than these can cause the display to turn very dark or very light
until the unit returns to the recommended operating temperature range.
Pi
Rain and Water Resistance
Water resistance can be impaired if the door of the battery compartment or top
cover is improperly closed or if the gaskets have deteriorated.
The handheld withstands exposure to rain without allowing water to
seep inside the unit. It is designed to endure occasional immersions, and
the unit floats making it easy to retrieve if dropped in water.
2-12
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Overview of the Neptune Handheld System
Electromagnetic Resistance
The Nomad performs well in most common environments where
electromagnetic fields are present. Examples of these environments
include areas near power-transmission lines, electric motors,
transformers, compressors, and low-power radio transmitters.
Performance can be degraded when using a communication cable, a
peripheral, such as a printer, or a battery charger under these conditions.
Shock Resistance
se
When the unit is operated within the specified temperature range, it can
withstand occasional drops from up to 1.22 meters (4 feet) onto a hard
surface.
el
ea
Use of the Nomad
tR
To set up and begin using your Nomad handheld, go to “Using the
Nomad Handheld,” on page 4-1.
The Display on the Handhelds
Pi
lo
Except for the chapter dedicated to setting up and using the CE5320B, this
manual uses the Nomad screens. However, the CE5320B screens are very
similar.
This section describes the display on the Neptune handheld system.
•
The types of information that are shown in the display of the
handheld.
•
An overview of how to use the screens to access different types of
information.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
2-13
Overview of the Neptune Handheld System
The Handheld Display
el
ea
se
Information in the display of the handheld is shown in three formats:
menu screens, data-entry screens, and message screens.
tR
Menu screens allow you to
choose from the icon options.
Data-entry screens prompts
you to select or enter data,
such as the meter number.
Pi
lo
Figure 2.6 Menu and Data-Entry Screen
2-14
N_SIGHT R900 User’s Manual for the Neptune Handheld System
se
Overview of the Neptune Handheld System
el
ea
Message screens display information or prompt you to make a
selection. They also can tell you how to exit the current screen or how
to access other screens.
Figure 2.7 Message Screens
tR
Menu Screens
lo
Menu screens typically display a list of options within a box and prompt
you to select one. To select an option from a menu screen, do one of the
following:
From the keypad, press the key whose number corresponds to the
item that you want to select. For example, if the menu displays a list
of trouble codes and the code that you want to select is number 3 in
key on the keyboard or keypad.
the list, then press the THREE
Your selection appears in the display.
Pi
•
•
or DOWN
key to move up or down the list
Use the UP
until the item that you want is highlighted.
ENTER
key on the CE5320 or the ENTER
Then press the ENTER
key or
on the Nomad. Your selection appears in the
or
to move forward,
display. You can also use the TAB
+ TAB
to move backward.
and the SHIFT
N_SIGHT R900 User’s Manual for the Neptune Handheld System
2-15
Overview of the Neptune Handheld System
A key that can be used to select an item from a list is called a hot key.
The procedures in this manual will instruct you to follow one or the
other method. Use the method most comfortable for you.
Data-Entry Screens
el
ea
se
Typically, data-entry screens prompt you to enter information.
Whenever a data-entry screen is displayed, the handheld automatically
disables inappropriate keys. For example, when prompted to enter a
meter reading, it allows you to enter numbers only. However, if you are
prompted to enter a new trouble code, it enables the letter and number
keys because codes can use letters and numbers.
Pi
lo
tR
On each of the reading-entry screens the meter reader can tell the
position of the meter within the route. See Figure 2.8 on Page 2-16.
Meter
position
UR = unread
Number of accounts
within route
Figure 2.8 Meter Position within Route
2-16
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Overview of the Neptune Handheld System
In this example, the number 1/5show us that the position of this meter is
1 out of 5 accounts contained on the route.
The reader can use
route.
and
to navigate to other accounts on the
Message Screens
se
Typically, message screens display messages as well as instructions for
exiting the message screen. For example, when a message, such as
Return handheld to office by 4pm to download
routes, is displayed, the instruction Press ESC key is also shown
to tell you how to exit the message screen. Sometimes you can be given
options for accessing other screens that contain information related to
the message shown in the display.
Navigating Through Screens
tR
el
ea
Some message screens only display information such as the number of
the meter whose reading-entry screen is shown. Because the
information displayed in message screens is linked to a particular meter
or route, pressing any key from this screen always returns you to the
reading-entry screen of the meter or route to which the message
belongs.
Pi
lo
There are two primary screens meter readers and operators use that give
them access to the screens they need: the Reading-Entry screen (a dataentry screen) and the F1 Menu (a menu screen).
N_SIGHT R900 User’s Manual for the Neptune Handheld System
2-17
el
ea
se
Overview of the Neptune Handheld System
tR
Generally, meter-readers use the
reading-entry screen to access
information they need to perform
their tasks.
Meter readers also use the
Start
key or the F1 menu to access
information and functions they need to
perform their tasks.
Figure 2.9 Navigating Screens
Pi
lo
You can display a reading-entry screen after routes have been
downloaded to the handheld by logging into the route. From the F1
menu or the Start key menu, you can access other screens, configure
probes, and check or change settings that control how the CE5320 and
Nomad exchanges information with the host computer.
To display screens that allow you to view or change information about a
meter or route, you must first
You can now make changes from the current meter you are on from the
Reading Entry screen and make changes to the route as well.
2-18
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Overview of the Neptune Handheld System
Icon Bar
The icon bar allows you to work with the Reading Entry screens. It
appears at the top of the screen similar to the one shown in Table 2.1.
Table 2.1 N_SIGHT R900 Display Icons
Display Icons
Main menu
se
Battery indicator
Next unread account
Route direction: points
el
ea
Tag account
Customer notes
Trouble codes
Pi
lo
tR
Comment Code
Cycles between one of these icon
displays
depending on the reading:
Keyed Read (Manual)
R900
Probe
Changes per type of account:
Read parameters (manual accounts)
Edit (radio and probe accounts)
If an icon appears as gray rather than black, it means that this icon is not available.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
2-19
Overview of the Neptune Handheld System
While you are on a reading entry screen, if you want to search to find a
specific account, you must first press
Start, then
Find Order.to display the Search screen.
tR
el
ea
se
Route, then
or press
Figure 2.10 Search Screen
Pi
lo
You can then select which field to search through, then enter the search
criteria to locate a specific account or group of accounts.
2-20
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Overview of the Neptune Handheld System
tR
el
ea
se
Press
or click
Start, then
Move, then
GoTo to
quickly maneuver through a route, such as going to the beginning of a
route or to the end of a route to display the GoTo screen. The handheld
goes to that point.
Figure 2.11 GoTo Screen
lo
On this screen you can go to the following points on a route:
Position of the meter within the route
•
Sequence number of the meter
•
Previous route
•
Next route
•
Beginning of the route
•
End of the route
•
First incomplete read
•
Last incomplete read
Pi
•
N_SIGHT R900 User’s Manual for the Neptune Handheld System
2-21
Overview of the Neptune Handheld System
Pi
lo
tR
el
ea
se
Notes
2-22
N_SIGHT R900 User’s Manual for the Neptune Handheld System
3 Using the CE5320 Handheld
se
If you want to set up and configure the Nomad handheld, see “Using the Nomad
Handheld,” on page 4-1
tR
el
ea
This chapter provides basic instructions for unpacking and inspecting
the CE5320 handheld. It also gives instructions for setting up the
CE5320 handheld and becoming familiar with the keyboard and display.
This chapter also provide help to get started with your CE5320 handheld
so that you can begin collecting information from the field and
exchanging information with the host computer.
Pi
lo
In addition, this chapter gives procedures for changing the system
settings, which affects how the handheld displays and accesses data.
Although these settings are preset by Neptune to meet the needs of most
meter reading processes, you can change some of the settings so that
they better suit your needs.
Determining the System Configuration
Although the handheld requires no installation, you do need to connect
the unit to a power supply to charge its battery and to a host computer to
allow it to communicate. How you make these connections depends
upon how you have configured your meter reading system.
The CE5320 handheld has one basic system configuration that is used
for local communications. A communication cradle is the most
commonly used method to charge and exchange data with a handheld.
See “Setting Up the CE5320,” on page 3-3. With this configuration,
N_SIGHT R900 User’s Manual for the Neptune Handheld System
3-1
Using the CE5320 Handheld
whenever the handheld is placed in a communication cradle, its battery
begins recharging, and it is ready to exchange data with the host
computer.
Local and Remote Communications
el
ea
Unpacking and Inspecting Equipment
se
The configuration previously described is used for local operations,
where the handheld and its communications equipment are directly
connected to the host computer. The cradle can also be used for remote
operations where the handheld and its communications equipment are in
an office remote from the host computer. In this situation, the remote
units are connected through the Internet to the host computer by an
Ethernet cable. After the connection is established, only the software on
the host computer and on the handheld need to be set up to manage a
communications exchange.
Besides using normal care, you need no special instructions to unpack
the handheld or the equipment that you purchased with it.
Pi
lo
tR
Check that you have received all the items you need for the type of
system configuration that you are using and inspect the items for
shipping damage. If you detect any damage, return the damaged
equipment to Neptune. Instructions for shipping the handheld to
Neptune are given in “Returning your Neptune Handheld System,” on
page 9-28 of this manual.
Save the packing box that was used to ship the handheld. Should you ever
need to ship the handheld, you need to repack the unit in its original shipping
box. The handling involved in land and air transport often subjects the
handheld to impact beyond that which occurs during normal use. The packing
box is designed to absorb shocks and protect the handheld during shipping.
3-2
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the CE5320 Handheld
Setting Up the CE5320
The following section describes how to set up your CE5320 so that you
can begin using it.
One CE5320 and a Communication Cradle
tR
el
ea
se
If you are using a communication cradle to power and exchange
information with one handheld at a time, check that you have received
the following items.
lo
Figure 3.1 Cradle and Charging Kit
One CE5320 handheld computer.
•
A cradle-charging kit, which is required for operation and is usually
ordered with the unit. It includes an AC adapter/battery charger
cable.
Pi
•
An Ethernet cable is required for communication; however, it is not included
in the kit.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
3-3
Using the CE5320 Handheld
The Router
It is important that the router you use has the capability to work as a switch.
tR
el
ea
se
If you are using a router to link cradles to exchange information with
more than one CE5320 at a time, check that you have the following
items.
Figure 3.2 Cradle, Router, and Cables Needed
One or more CE5320 handheld computers.
•
One communication cradle for each CE5320.
Pi
lo
•
•
One AC adapter/battery charger cable.
•
One RJ45 Ethernet cable for each communication cradle.
•
One RJ45 Ethernet cable to connect the router to the Personal
Computer (PC).
•
One AC power supply cable.
In order for the Communications function to work properly, a standard RJ45 Ethernet cable must be used.
3-4
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the CE5320 Handheld
Connecting to the Host Computer and Power Supply
This configuration is for handhelds not connected to a system network. If you
are connected to a system network, see the network specialist or your System
Administrator for assistance.
se
The procedures in this chapter describe how to connect the CE5320 to
the host computer so that it can exchange information with the host. The
procedures also describe how to connect a power supply to the
communications cradle so that you can recharge the battery. Complete
the following procedures to connect the equipment you have.
Connecting the Router, CE Handheld Cradle, and Power
Supplies
el
ea
You need no special tools to connect the devices that were shipped with
your handheld. Follow this procedure to connect the router,
communication cradles, and power supplies.
If you have not already done so, make sure that you have all of the
equipment you need. If necessary, refer to the preceding section
“Unpacking and Inspecting Equipment,” on page 3-2.
lo
tR
It is important that the router you use has the capability to work as a switch.
With the host computer OFF, connect the power supply to the
router.
Pi
N_SIGHT R900 User’s Manual for the Neptune Handheld System
3-5
Using the CE5320 Handheld
Leaving the far left port empty, connect one end of the RJ-45
Ethernet cable into one of the four slots in the router. See Figure
3.3.
Always leave far left
port empty
se
el
ea
RJ-45 Ethernet cable
Figure 3.3 Connecting RJ-45 Ethernet Cable to Router, Port 1
Connect the other end of the Ethernet cable to the host computer.
Push the single-hole connector of the 110V AC adapter/battery
charger onto the single-prong connector on the back of the
communication cradle.
tR
Pi
lo
Secure the connector by turning its grooved lock-nut clockwise
until you feel resistance. See Figure 3.4.
Figure 3.4 Connecting the Power Cable to the Communications Cradle
3-6
Connect the other end of the AC adapter/battery charger into a
power source.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the CE5320 Handheld
With an additional Ethernet cable, insert one of its connectors into
the back of the cradle and the other the other end into the back of
the router. See Figure 3.5.
se
Connect the network cable to the single router.
Network cable
from cradle
Pi
lo
tR
el
ea
Figure 3.5 Connecting the Ethernet RJ-45 Cable to the Cradle
RJ-45 Ethernet cable to host computer
Figure 3.6 Network Cable Connection
N_SIGHT R900 User’s Manual for the Neptune Handheld System
3-7
Using the CE5320 Handheld
To connect additional cradles to a router, repeat steps 7 and 8, using
the available ports on the router. See Figure 3.7.
Network cable from
cradle 1
el
ea
RJ-45 Ethernet cable to
host computer
se
Always leave far
left port empty
RJ-45 Ethernet cable to another
handheld cradle or another router
tR
Figure 3.7 Connecting Multiple Handheld Cradles to Router
Pi
lo
Port number 1 is always reserved for the network cable, and the port marked
Internet is always kept empty.
You can connect another router to the main router you are using by
connecting one end of an additional Ethernet cable into an open port on the
main router and the other end to an open port on the additional router.
3-8
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the CE5320 Handheld
Configuring the CE5320 Handheld
On the Host Computer
On the Host Computer, right-click on My Computer.
Select Properties
Click Computer Name.
Record the computer name for the Host Computer here:
Click Start, then Run.
Type CMD and press Enter.
el
ea
se
___________________________________________________
A DOS window appears.
Type ipconfig and press Enter.
Write the IP address here: _____________________________
Type exit and press Enter to close the DOS window.
tR
On the CE5320 Handheld
Pi
lo
Before proceeding with this section, you must complete the information for the
handhelds in two tables within the N_SIGHT R900 host software: Handhelds
and Reader ID. Refer to the N_SIGHT R900 Online HTML Help for the steps
to complete this information in these tables.
On the N_SIGHT R900 Login screen, press M or touch Menu.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
3-9
Using the CE5320 Handheld
se
The N_SIGHT R900 Main Menu screen appears.
Figure 3.8 N_SIGHT R900 Main Menu
Select 1, Admin.
el
ea
Pi
lo
tR
The Admin Menu appears as illustrated in Figure 3.9.
Figure 3.9 N_SIGHT R900 Admin Menu
Select 4, Reset Handheld.
Do not press Reset Handheld if the handheld is not in the communications cradle.
3-10
Click Yes.
Leave the password field blank, or if required, type BUBBA.
Click OK.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the CE5320 Handheld
The Communications Configuration screen appears.
Tab to the HHU ID field, and type the ID of the handheld.
The HHU ID number is located on the back of the CE5320 handheld under
the top part of the strap. It must also match exactly with what has been
entered in the host software for that particular handheld.
Type the IP address in the Server Name field.
Be sure the Port is 25100.
10 Touch Connect or OK.
se
The Display and Keyboard
el
ea
The N_SIGHT R900 Login screen appears.
This section describes the display and keyboard on the CE5320.
An overview of how to use the keys to access different types of
information.
lo
•
The types of information that are shown in the display of the
handheld.
tR
•
Learning the Keyboard
Pi
The CE5320 handheld uses 51 keys to give you access to all the stored
information and to allow you to enter new data. Most keys perform
more than one function.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
3-11
Using the CE5320 Handheld
Function keys
Direction keys
Number keys
Quick keys
Information keys
el
ea
se
Letter/character keys
tR
Figure 3.10 Learning the Keyboard
Function Keys or Hot Keys—allow you to perform special tasks
quickly.
•
Direction Keys—allow you to move up or down a list of items and
to move forward or backward in a data-entry space or through the
meters of a route.
Pi
lo
•
3-12
•
Number Keys—allow you to enter a number in the display or to
select an item from a list of items shown.
•
Quick Keys—allow you to execute a task quickly by pressing
certain keys at once or in a particular order.
•
Letter/Character Keys—allow you to enter a letter or character in
a screen or to select an item from a list of items shown.
•
Information Keys—allow you to enter, change, or view
information about a meter or a route.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the CE5320 Handheld
To help you perform handheld tasks, the keyboard is color coded. For
example, by using the BLUE
key in conjunction with keys that have
blue characters printed on them, you can enter a character, such as “?”
or “#”. Keys with black numbers or letters are single-entry keys. To
enter the number or letter, simply press the key with the corresponding
number or letter. Keys that have information printed in white above
them allow you to enter or change specific information about a meter or
route.
F1 Function Keys
se
Because the CE5320 automatically disables inappropriate keys, the type
of task that you can perform from the keyboard depends upon the type
of menu that is displayed.
Pi
lo
tR
F1
el
ea
The function keys on the CE5320 are the top row of yellow keys that are
labeled with an F (for function) and a number. Function keys allow you
to perform special tasks quickly.
F2
If the unit is powered off, pressing F1 will power
it on and pressing BLUE
F1 while the unit
is on, will turn it off. The Help feature is not yet
supported.
In addition, F1 allows you to access the Main
Menu for N_SIGHT R900, where you can access
the functions available to you while using the
CE5320 handheld.
While reading a route, pressing F2 accesses the
previous incomplete reading.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
3-13
Using the CE5320 Handheld
While reading a route, pressing F3 accesses the
next incomplete reading.
F3
In addition, pressing BLUE
unit is on accesses the backlight.
F3 while the
Number Keys
el
ea
se
The number keys on the handheld are used most often for entering
readings. Because entering readings is the primary function of users, the
number keys are larger than other keys and are placed near the top of the
keypad. Number keys enable you to complete one of two tasks:
•
Enter a number in the display, such as for a reading.
•
Select an item by pressing the number key that corresponds to a
numbered item in a list of items.
tR
The type of task that you can perform using a number key depends upon
the type of screen that is displayed.
Menu Screen—select a numbered item from the list by pressing
the key whose number corresponds to the item that you want to
select. (When used this way, the number key is called a hotkey.)
lo
•
Pi
•
Data-Entry Screen—enter a number in the data-entry screen by
pressing the key with the number that you want to appear in the
field.
Direction Keys
The direction keys on the handheld are used to move up or down
through a list of items displayed in a menu screen and to move forward
or backward within a data-entry space or through the meters of a route.
Pressing the direction key up or down displays additional screens for the
account, such as an account-specific hazard.
3-14
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the CE5320 Handheld
The type of task that you can perform using a number key depends upon
the type of screen displayed.
Menu Screen—highlights a numbered item in the list of items
or DOWN
key to move
displayed by pressing the UP
or
through the list of items. You can also use the BACKWARD
FORWARD
keys to jump to the first or last item in the menu. As
you reach an item, it becomes highlighted.
•
Data-Entry Screen—moves forward or backward within a dataor BACKWARD
key
entry space by pressing the FORWARD
to move forward or backward within the space.
se
•
Reading-Entry Screen—display the reading-entry screen of the next
or previous meter by pressing the FORWARD
or BACKWARD
key.
tR
•
el
ea
Moving over existing letters or numbers will not erase them.
A Letter/Character Keys
Pi
lo
The letter/character keys on the handheld are the keys that are labeled
with the letters of the alphabet and with special characters, which are
printed in blue to the right of each letter. Letter/character keys enable
you to complete one of three tasks:
•
Enter a letter in a data-entry screen.
•
Enter a character in a data-entry screen.
•
Select an item by pressing the key whose letter corresponds to the
item that you want to select.
Use the color coding to remember which keys to use with character keys:
key followed by a letter/character key (characters are
press the BLUE
shown in blue on these keys) to display the character in the screen.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
3-15
Using the CE5320 Handheld
Menu Screen—select an item from the list by pressing the key
whose letter corresponds to the item that you want to select. (When
used this way, the letter/character key is called a hotkey.)
•
Data-Entry Screen—enter a letter in the data-entry screen by
pressing the key of the letter that you want to appear in the datakey followed by the letter
entry screen or by pressing the BLUE
you want to appear in the display.
•
Reading-Entry Screen—perform a function by pressing the key
over which the name of the function is printed in white (detailed
next).
el
ea
Information Keys
se
•
Information keys only work when logged into the handheld (Production
Mode).
Pi
lo
tR
The information keys on the handheld are the letter/character keys that
have information printed in white above them. You can enter, change, or
view the following information about a meter or a route by pressing the
appropriate key whenever a reading-entry screen is shown in the
display.
3-16
Toggles between the Automatic Meter Reading
(AMR) mode: R900
Keyed
Advantage
R300.
Accesses the Codes menu allowing you to enter
trouble codes or customer notes depending upon
the type of import file you are using.
Allows you to turn the Edit mode ON. In edit mode,
you can type information on screens that allow text
entry.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the CE5320 Handheld
Allows you to access the Search screen where you
can select criteria to look for information you need:
•
•
•
•
•
•
•
•
•
•
•
•
lo
Pi
Allows you to access the GoTo screen. On this
screen, you can access the following information for
a meter or a route:
el
ea
tR
Coded note
Route
Meter number
Name
Meter type
Account status
Sequence number
Skip code
Instruction code
Account number
Constant
Tag
se
•
•
•
•
•
•
•
•
Position of the meter within the route
Sequence number of the meter
Previous route
Next route
Beginning of the route
End of the route
First incomplete read
Last incomplete read
Allows you to view summary information about the
route. When pressed with the CTL key, this key
allows you to view screen information for the
handheld, such as the version number, Internet
Protocol (IP) Address, Random Access Memory
(RAM), and storage.
Allows you to enter a reading manually.
Allow you enter List mode where the account
addresses are presented in list form, a convenient
way to browse through the accounts.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
3-17
Using the CE5320 Handheld
Allows you to access the Meter Menu where you
can skip a reading, change meter information, and
enter information for a found meter.
Allows you to view the Properties information for the
handheld:
’
Allows you to tag the account, so that you can come
back to it later.
Allows you to log out of N_SIGHT R900 after
completing the required information.
tR
–
Allows you to skip the reading for this account.
el
ea
lo
Y`
Allows you to search for the accounts already
tagged.
Allows you to perform an RF test.
Pi
Z´
Read direction
Route dir
Battery key clicks
Date
Time
se
•
•
•
•
•
You can use these keys only when a reading-entry screen is displayed.
For example, if the you need more information about this meter,
pressing the INFORMATION
or
keys while reading the account,
will take you to additional information. Once you display the
information you need, pressing these keys again returns you to meter’s
reading-entry screen.
3-18
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the CE5320 Handheld
DEL
Quick Keys
By pressing specific keys at once, or in a particular order, you can
execute a task quickly. Certain quick key tasks can be performed no
matter what type of screen is shown. The following table summarizes
tasks that you can perform using quick keys.
Press F1
To turn on the CE5320.
DEL
DEL
..
To enter a reading or select an item
from a menu screen.
tR
Press
ENTER
INS
ESC
lo
Press
To enter a decimal point. (This is
typically required only by “floating
point” meters.)
To return to the preceding screen.
To enter a space when entering a
special message or other data.
Pi
Press
To erase a letter, number, or
character that you have entered.
As you backspace over each letter,
number, or character, each is
erased.
Press
Press
To turn off the CE5320.
el
ea
, F1
Press BLUE
Press
se
Use the color coding to remember which keys to use with quick keys that have
two functions: to activate the function printed in blue, press the BLUE
key first, and then press the key with a function printed in blue.
CTL
ALT
N_SIGHT R900 User’s Manual for the Neptune Handheld System
To show meter information on the
screen.
3-19
Using the CE5320 Handheld
Press BLUE
Press F1 ,
To backlight the display and the
keys, if your CE5320 Handheld has
the keyboard backlight option.
Pressing these keys again will turn
off the backlight. These keys work
as a toggle.
, F3
To reboot the CE5320 Handheld.
, then
se
Backlighting can drain the battery rapidly. To conserve the battery, use this
feature only in low light.
Adjusting System Settings
el
ea
If you do not press a key within 45 seconds of activating this feature, the
CE5320 automatically deactivates the backlight to conserve battery power.
lo
tR
System settings affect how the handheld displays and accesses data.
Although these settings are factory-set to meet the needs of most meter
reading processes, you can change some of the settings so that they
better suit your needs. These settings are typically set once and never
changed; however, you can adjust these settings any time.
Calibrating the Stylus
Pi
The CE5320 handheld has a touchscreen display that uses a stylus for
ease-of-use. Because each person’s touch differs, it is important to
calibrate the stylus to the touchscreen for the user’s own personal touch.
All functions are available without the stylus by using keyboard.
To calibrate the stylus, complete the following procedure.
3-20
On the N_SIGHT R900 Login screen, press M or touch Menu.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the CE5320 Handheld
The N_SIGHT R900 Main Menu screen appears.
se
Figure 3.11 N_SIGHT R900 Main Menu
Press 6 or touch item 6: Handheld.
Press 9 or touch 9: Stylus.
el
ea
Pi
lo
tR
The Stylus Calibration screen appears like Figure 3.12.
Figure 3.12 N_SIGHT R900 Stylus Calibration Screen
Calibration is simply done by touching the center of the cross with
the stylus for a couple of seconds. When the cross moves to another
place, repeat the operation.
Hold your stylus on the cross until it moves.
Remember just to touch the screen; there is no need to press hard or to
punch it.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
3-21
Using the CE5320 Handheld
The cross moves to another location on the screen similar to that
illustrated in Figure 3.13.
se
Figure 3.13 Stylus at Another Location on Screen
Repeat holding the stylus on the cross until it moves.
When finished, press
el
ea
ENTER
The handheld returns to N_SIGHT R900 Main Login screen.
tR
Changing the Handheld Properties
The section allows you to adjust or change the following properties for
the handheld:
Key clicks
•
Reading entry direction
Pi
lo
•
•
Route direction
Working with the Properties Screen
To access the Properties screen, complete these steps.
3-22
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the CE5320 Handheld
On any reading
entry screen, press
The Properties
screen appear as
illustrated in
Figure 3.14.
Do one or both of the following:
•
Proceed to “Changing the Reading Entry Direction,” in the
next section.
•
Change the “Changing the Route Read Direction,” on page
3-24.
el
ea
se
Figure 3.14 Handheld Properties Screen
tR
Changing the Reading Entry Direction
As you enter a reading in the handheld, each number can be displayed
from right to left or from left to right.
In the Read Dir field, touch the down arrow and do one of the
following:
lo
Select LEFT TO RIGHT if you want the number to begin
from the left.
•
Select RIGHT TO LEFT if you want the number to begin
from the right.
Pi
•
These setting toggle between Left to Right or Right to Left
according to the current setting.
This procedure affects only accounts whose directions have not been set by
the host computer. If the reading-entry direction of an account has been set
by the host computer, the host setting replaces your setting.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
3-23
Using the CE5320 Handheld
Changing the Route Read Direction
The handheld typically displays meters of a route from the first meter to
the last meter. However, you can change the order that meters are
displayed so that they are shown from the last meter to the first meter.
In the Route Dir field, touch the down arrow and do one of the
following:
•
Select FORWARD if you want the readings to advance to the
next unread account in the route.
•
Select BACKWARD if you want to change the directions of
the readings to go backward to the previous unread account in
the route.
se
el
ea
These settings toggles between Forward or Backward according to
the current setting.
Turning Key Clicks On and Off
tR
The Key Clicks feature allows you to control how the handheld
responds when you press a key. When this feature is ON, the handheld
beeps whenever you press a key. Turning the Key Clicks feature on can
help you reduce errors by making sure that you press each key fully. If
you do not press a key fully, the handheld does not acknowledge your
entry. You can turn the Key Clicks feature on or off at any time.
Do one of the following:
Pi
lo
•
Select the checkbox to enable Key Clicks.
•
Leave the checkbox empty to disable the Key Clicks.
These settings toggles between on (checked) or off (unchecked)
according to the current setting.
Touch OK to save your settings.
You return to the reading-entry screen or your previous screen.
Configuring RF/Serial Properties
Depending on the type of accounts on your route, you may have to
configure the RF antenna, the type of probe, or serial properties you are
using. Follow this procedure to configure or change the RF antenna, the
type of probe, or serial properties.
3-24
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the CE5320 Handheld
Press
F1
se
The F1 Menu
appears as
illustrated in
Figure 3.15.
Touch
el
ea
Figure 3.15 N_SIGHT R900 F1 Menu
Pi
lo
tR
The System Menu
appears as illustrated
in Figure 3.16.
Touch
Figure 3.16 N_SIGHT R900 System Menu
N_SIGHT R900 User’s Manual for the Neptune Handheld System
3-25
Using the CE5320 Handheld
The RF/Serial
Properties screen
appears as illustrated
in Figure 3.17.
el
ea
Logging In and Out of the N_SIGHT R900
se
Figure 3.17 RF/Serial Properties Screen
This section explains how to log into N_SIGHT R900 on the handheld
to access the screens needed to complete meter reading tasks.
Logging Into N_SIGHT R900 on the CE5320
tR
After you have loaded a route, or after you have exchanged meter
readings and route data with the host computer, you need to log into
N_SIGHT R900 on the handheld. Signing on gives you access to the
screens you need to collect and exchange route and meter data.
lo
Complete the following steps to log into N_SIGHT R900 on the
CE5320.
Pi
If you have not already done so, press
F1
turn on the CE5320.
If you see the message Not Uploaded, this means the handheld has
been loaded but not yet been unloaded. This is normal if a new route was just
loaded to the handheld.
’
Touch S
or Synchronize to start Communications. For more
information, refer to “Communicating with the Host Computer,” on page 7-1.
3-26
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the CE5320 Handheld
You can see a message
like the one illustrated in
Figure 3.18.
Message area
Version number
Click
el
ea
se
Figure 3.18 N_SIGHT R900 Message Area
tR
There may be times when the Clock Error screen appears when you are
attempting to log in. When this screen appears, continue with the following
steps.
Pi
lo
A Clock Error screen
appears, prompting you
to log on to manually set
the clock, as illustrated in
Figure 3.19.
Figure 3.19 N_SIGHT R900 Clock Error Screen
N_SIGHT R900 User’s Manual for the Neptune Handheld System
3-27
Using the CE5320 Handheld
Click Yes.
If you answer NO to the
clock error message, the
Login screen appears again.
After you click Yes, the
Set Date/Time screen
appears as illustrated in
Figure 3.20.
se
Figure 3.20 N_SIGHT R900 Set Date / Time Screen
If applicable, make any changes to the date and time.
el
ea
The correct date and time to use is the date and time that the
handheld last synchronized.
When the date and time
are accurate, click OK.
Pi
lo
tR
The Handheld Login
screen appears as
illustrated in Figure 3.22.
Figure 3.21 N_SIGHT R900 Handheld Login Screen
The Reader ID field displays the information contained in the
N_SIGHT R900 software.
3-28
Complete the following information as applicable:
•
Password (Determined by N_SIGHT R900 setup)
•
Vehicle # (Optional)
•
Mileage (Optional)
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the CE5320 Handheld
Click
The Select Route screen
appears as illustrated in
Figure 3.22.
Highlight the route you
want, and click OK.
Figure 3.23 N_SIGHT R900 Initializing Message
lo
tR
el
ea
A message appears
similar to the one
illustrated in Figure
3.23.
se
Figure 3.22 N_SIGHT R900 Select Route Screen
Pi
When the software has finished initializing, a Reading Entry screen
indicating that the sign on process is complete and that the unit is
ready for use in collecting readings. See Figure 3.24.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
3-29
Using the CE5320 Handheld
se
For assistance in using
the CE5320 to collect
meter readings, refer to
“Gathering Route
Data,” on page 6-1.
Logging Out of N_SIGHT R900
el
ea
Figure 3.24 N_SIGHT R900 Reading Entry Screen
tR
The only time that you need to log out of N_SIGHT R900 on the
handheld is just before you begin exchanging information with the host
computer. Logging out gives you access to the communication features
of the handheld. Instructions for logging out on the handheld are
included in the procedures that describe how to exchange information
with the host computer. For more information, see “Exiting the
Software,” on page 7-1.
Pi
lo
If you allow the handheld to remain inactive for the factory-set delay of
45 seconds or for the delay time specified by the host computer, it turns
off automatically. After this period of inactivity, the screen of the
handheld goes blank and the unit turns off to conserve the battery.
3-30
N_SIGHT R900 User’s Manual for the Neptune Handheld System
4 Using the Nomad Handheld
se
If you want to set up and configure the CE5320 handheld, see “Using the CE5320
Handheld,” on page 3-1.
tR
el
ea
This chapter provides basic instructions for unpacking and inspecting
the Nomad. It also gives instructions for setting up the Nomad and
becoming familiar with the keyboard and display. This chapter also
provides help to get started with your Nomad, so that you can begin
collecting information from the field and exchange information with the
host computer.
Pi
lo
In addition, this chapter gives procedures for changing the system
settings, which affects how the handheld displays and accesses data.
Although these settings are preset by Neptune to meet the needs of most
meter reading processes, you can change some of the settings so that
they better suit your needs.
Unpacking the Nomad
Besides using normal care, you need no special instructions to unpack
the handheld or the equipment that you purchased with it.
Check that you have received all the items you need and inspect the
items for shipping damage. If you detect any damage, return the
damaged equipment to Neptune. Instructions for shipping the handheld
to Neptune are given in “Returning your Neptune Handheld System,”
on page 9-28 of this manual.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
4-1
Using the Nomad Handheld
Inside the box with the Nomad is an Orientation Guide that exhibits the
contents:
Hand strap
•
Battery
•
Trimble Nomad getting started disk
•
AC adapter
•
USB cable
•
Stylus
•
Screen protectors
•
4GB SD card (also included in the box)
el
ea
se
•
The Guide shows you how to do the following:
Install the battery
•
Attach the hand strap
•
Insert the SD card
Pi
lo
tR
•
4-2
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the Nomad Handheld
Setting Up the Nomad
The following section describes how to set up your Nomad so that you
can begin using it.
One Nomad and a Communication Cradle
se
If you are using a communication cradle to power and exchange
information with one handheld at a time, check that you have received
the following items.
Pi
lo
tR
el
ea
Battery LED
USB host
Figure 4.1 Nomad and Cradle Charger
•
One Nomad handheld computer.
•
The charger that is included with the Nomad can be used to power
the Communications Cradle. If you want a separate charger, you
can order it as an accessory.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
4-3
Using the Nomad Handheld
The Router
It is important that the router you use has the capability to work as a switch.
If you are using a router to link cradles to exchange information with
more than one Nomad at a time, check that you have the following
items:
One or more Nomad handheld computers.
•
One communication cradle for each Nomad.
•
One AC adapter/battery charger cable for each cradle.
•
One RJ45 Ethernet cable for each communication cradle.
•
One RJ45 Ethernet cable to connect the router to the PC.
•
One router/switch with one AC power supply cable.
tR
el
ea
se
•
lo
In order for the Communications function to work properly, a standard RJ45 Ethernet cable must be used.
Pi
Connecting to the Host Computer and Power Supply
This configuration is for handhelds not connected to a system network. If you
are connected to a system network, see the network specialist or your system
administrator for assistance.
The procedures in this chapter describe how to connect the Nomad to
the host computer so that it can exchange information with the host. The
procedures also describe how to connect a power supply to the
communications cradle so that you can recharge the battery. Complete
the following procedures to connect the equipment you have.
4-4
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the Nomad Handheld
You need no special tools to connect the devices that were shipped with
your handheld.
Connecting the Router, Nomad Handheld Cradle, and Power
Supplies
Follow this procedure to connect the router, communication cradles, and
power supplies.
se
You need a network switch or it is important that the router you use has the
capability to work as a switch.
If you have not already done so, make sure that you have all of the
equipment you need. If necessary, refer to the preceding section
“Unpacking the Nomad,” on page 4-1.
With the host computer OFF, connect the power supply to the
router.
Leaving the far left port empty, connect one end of the RJ-45 Ethernet cable into one of the four slots in the router. See Figure 4.2.
Pi
lo
tR
el
ea
Always leave far left
port empty
RJ-45 Ethernet cable
Figure 4.2 Connecting RJ-45 Ethernet Cable to Router, Port 1
Connect the other end of the Ethernet cable to the host computer.
Push the single-hole connector of the 110V AC adapter/battery
charger onto the single-prong connector on the back of the communication cradle.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
4-5
Using the Nomad Handheld
Power input
se
Ethernet
connection/
data transfer
RJ45 Ethernet
USB client
el
ea
Figure 4.3 Nomad Communications Cradle Connections
Connect the other end of the AC adapter/battery charger into a
power source. See Figure 4.3.
With an additional Ethernet cable, insert one of its connectors into
the back of the cradle and the other into the back of the router. See
Figure 4.3.
tR
Connect the network cable to the single router.
Network cable
from the cradle
Pi
lo
RJ-45 Ethernet cable to the host computFigure 4.4 Network Cable Connection
4-6
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the Nomad Handheld
Configuring the Nomad Handheld
On the Host Computer
On the host computer, click Start.
Type CMD and press Enter.
A DOS window appears.
Type ipconfig and press Enter.
Write the IP address here: _____________________________
Type exit and press Enter to close the DOS window.
el
ea
On the Nomad Handheld
se
tR
Before proceeding with this section, you must complete the information for the
handhelds in two tables within the N_SIGHT R900 host software: Handhelds
and Reader ID. Refer to the N_SIGHT R900 Online HTML Help for the steps
to complete this information in these tables.
On the N_SIGHT R900 Login screen, press M or touch
Pi
lo
The N_SIGHT R900 Main Menu screen appears.
Figure 4.5 N_SIGHT R900 Main Menu
N_SIGHT R900 User’s Manual for the Neptune Handheld System
4-7
Using the Nomad Handheld
Select
, Admin.
el
ea
se
The Admin Menu appears as illustrated in Figure 4.6.
tR
Figure 4.6 N_SIGHT R900 Admin Menu
Select
, Reset Handheld.
Pi
lo
Do not press Reset Handheld if the handheld is not in the communications cradle.
Click Yes.
Leave the password field blank, or if required, type BUBBA.
Click OK.
The Communications Configuration screen appears.
4-8
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the Nomad Handheld
Tab to the HHU ID field, and type the ID of the handheld.
The HHU ID for the Nomad can be found four ways:
•
On the outside of the box in which the Nomad is packaged.
•
In the battery compartment on the right side.
•
Navigate to Windows Icon, Settings, System Tab at bottom of the
screen, and then scroll to System Information and Info Tab at bottom of
screen.
•
Navigate to Windows Icon, Settings, System Tab at bottom of the
screen and click About then Device ID at the bottom of the screen.
Type the IP address of the PC which you want the Nomad to
synchronize within the Server Name field.
Be sure the Port is 25101.
el
ea
10 Click OK.
se
The handheld resets, and the N_SIGHT R900 Login screen
appears.
tR
The Display and Keyboard
Pi
lo
If the message DB Uninitialized flashes on the screen press Synchronize
once more to complete Database Synchronization
This section describes the display and keyboard on the Nomad.
•
The types of information that are shown in the display of the
handheld.
•
An overview of how to use the keys to access different types of
information.
Learning the Keyboard
The Nomad handheld uses 51 keys to give you access to all the stored
information and to allow you to enter new data. Most keys perform
more than one function.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
4-9
Using the Nomad Handheld
Letter/character keys
el
ea
se
Application soft keys
Direction keys
Number keys
tR
Function key
Quick keys
Figure 4.7 Learning the Keyboard
lo
Buttons and Keys
Pi
In addition to an environmental seal that protects the unit from dust, dirt,
and water, the Nomad includes the following features.
4-10
•
Function Button—allows you to perform special tasks quickly.,
such as navigate through a screen when you use the yellow arrow
keys
•
Direction Buttons—allow you to navigate and move up or down a
list of items and to move forward or backward in a data-entry space
or through the meters of a route.
•
Number Buttons—allow you to access accounts while reading
meters.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the Nomad Handheld
•
Letter/Character Keys—allow you to enter a letter or character in
a screen or to select an item from a list of items shown.
•
Application Soft Buttons—allow you to enter, change, or view
information about a meter or a route.
•
Combination Keys—allow you to execute a task quickly by
pressing certain keys at once or in a particular order.
Buttons
se
To help you perform handheld tasks, the keyboard is color coded. For
el
ea
example, by using the yellow
function button in conjunction with
keys that are marked in yellow, you can navigate around a screen.
Buttons with white numbers or symbols are single-entry keys. To enter
the number, simply press the button with the corresponding number or
letter.
Function Button
tR
Because the Nomad automatically disables inappropriate buttons, the
type of task that you can perform from the keyboard depends upon the
type of menu that is displayed.
lo
On the numeric keypad, the yellow
function button (clicky key
sounds) accesses the tasks in yellow, including the navigation arrows.
Several settings can be changed under Keyboard Options.
Pi
Auto release: Press and release
to access a yellow task for one
use. It then goes back to the original key tasks.
to toggle it on and off.
Manual release: This is the default. Press
Yellow tasks remain active until the function key is pressed again.
Disabled:
must be held down while pressing any other key to
access the yellow task.
Play Sticky Key Sounds: To disable clicky key sounds, remove the
check in the box.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
4-11
Using the Nomad Handheld
Direction Buttons
In conjunction with the yellow
function button, the yellow
direction arrows are enabled by the number buttons closest to them. You
can use these buttons on the handheld to move up or down through a list
of items displayed in a menu screen, and to move forward or backward
within a data-entry space or through the meters of a route. Using
and pressing the arrow/number button up or down displays additional
screens for the account.
se
The type of task that you can perform using an arrow/number button
depends upon the type of screen displayed.
Data-Entry Screen—moves forward or backward within a dataor
entry space by pressing
+ BACKWARD
FORWARD
buttons.
el
ea
•
tR
Moving over existing letters or numbers will not erase them.
Reading-Entry Screen—displays the reading-entry screen of the
next or previous meter by pressing the
+ FORWARD
buttons.
or
+ BACKWARD
lo
•
Number Buttons
Pi
The number buttons on the handheld are used most often for entering
readings. Because entering readings is the primary function of users, the
number buttons are smaller than the other buttons and are placed in the
center of the keypad. Number buttons enable you to complete one of
two tasks:
4-12
•
Enter a number in the display, such as for a reading.
•
Select an item by pressing the number key that corresponds to a
numbered item in a list of items.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the Nomad Handheld
The type of task that you can perform using a number key depends upon
the type of screen that is displayed.
•
Menu Screen—select a numbered item from the list by pressing
the key whose number corresponds to the item that you want to
select. (When used this way, the number key is called a hotkey.)
•
Data-Entry Screen—enter a number in the data-entry screen by
pressing the key with the number that you want to appear in the
field.
se
Nomad Screen Keyboard
el
ea
When you tap the keyboard
icon located at the bottom of the
screen, an on-screen keyboard appears with 60 keys to use. There are
three views of this keyboard.
Changing the Size of the Keys
There are two ways you can change the size of the keys that display on
the screen keyboard.
Click the
at the top left of the screen.
lo
tR
Using the Windows Icon.
Click Settings, and then click Input.
Select Large Keys. (The default is Small Keys.)
Pi
Click OK.
Using the Keyboard Icon.
Click
at the bottom center of the screen.
Click
Click Options.
Select Large or Small Keys. See Figure 4.8 and Figure 4.9 on
Page 4-14.
Click OK.
to the right of the Icon.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
4-13
Using the Nomad Handheld
Large Keys
The following figure illustrates the large keyboard.
Figure 4.8 Nomad Large Keyboard
Small Keys
el
ea
se
The following figure illustrates the small keyboard.
Figure 4.9 Nomad Small Keyboard
tR
Lowercase Keys
Pi
lo
The following figure illustrates the lowercase QWERTY keyboard.
Figure 4.10 Nomad Lowercase Keyboard
Uppercase Keys
The following figure illustrates the uppercase QWERTY keyboard.
4-14
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the Nomad Handheld
To use the uppercase keys, tap
or
Figure 4.11 Nomad Uppercase Keyboard
Numeric and Symbols Keys
se
The following figure illustrates the keyboard with numeric and symbols
keys.
el
ea
To use the numeric and symbols keys, tap
tR
Figure 4.12 Nomad Numeric and Symbols Keyboard
lo
Information Keys
Pi
Information keys only work when logged into the handheld (Production
Mode).
The information keys on the handheld screen are the letter/character
keys that allow you to perform specific tasks while in N_SIGHT R900.
You can enter, change, or view the following information about a meter
or a route by pressing the appropriate key whenever you are logged into
a route and a reading-entry screen is shown in the display.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
4-15
Using the Nomad Handheld
Toggles between the Automatic Meter Reading
(AMR) mode: R900
Keyed
Advantage
R300.
Accesses the Codes menu, allowing you to enter
trouble codes or customer notes depending upon
the type of import file you are using.
se
Allows you to turn the Edit mode ON. In edit mode,
you can type information on screens that allow text
entry.
Allows you to access the Search screen where you
can select criteria to look for information you need:
Coded note
Route
Meter number
Name
Meter type
Account status
Sequence number
Skip code
Instruction code
Account number
Constant
Tag
Pi
lo
tR
el
ea
•
•
•
•
•
•
•
•
•
•
•
•
Allows you to access the GoTo screen. On this
screen, you can access the following information for
a meter or a route:
•
•
•
•
•
•
•
•
4-16
Position of the meter within the route
Sequence number of the meter
Previous route
Next route
Beginning of the route
End of the route
First incomplete read
Last incomplete read
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the Nomad Handheld
Allows you to view summary information about the
route. When pressed with the CTL key, this key
allows you to view screen information for the
handheld, such as the version number, Internet
Protocol (IP) Address, Random Access Memory
(RAM), and storage.
Allows you to enter a reading manually.
se
Allows you enter List mode where the account
addresses are presented in list form, a convenient
way to browse through the accounts.
el
ea
Allows you to access the Meter Menu where you
can skip a reading, change meter information, and
enter information for a found meter.
Pi
lo
tR
Allows you to view the Properties information for the
handheld:
•
•
•
•
•
Read direction
Route dir
Battery key clicks
Date
Time
Allows you to skip the reading for this account.
Allows you to tag the account so that you can come
back to it later.
Allows you to log out of N_SIGHT R900 after
completing the required information.
Allows you to search for the accounts already
tagged.
Allows you to perform an RF test.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
4-17
Using the Nomad Handheld
You can use these keys when a reading-entry screen is displayed. For
example, if the you need to find more information about this meter, do
the following:
or DOWN
Press UP
keys while reading the account.
This takes you to additional information. Once you display the
information you need, pressing these keys again returns you to meter’s
reading-entry screen.
Direction Keys
el
ea
se
The direction keys on the handheld are used to move up or down
through a list of items displayed in a menu screen and to move forward
or backward within a data-entry space or through the meters of a route.
Pressing the direction key up or down displays additional screens for the
account, such as an account-specific hazard.
The type of task that you can perform using a number key depends upon
the type of screen displayed.
Menu Screen—highlights a numbered item in the list of items
or DOWN
keys to move
displayed by pressing the UP
or
through the list of items. You can also use the BACKWARD
FORWARD
keys to jump to the first or last item in the menu. As
you reach an item, it becomes highlighted.
lo
tR
•
Pi
•
4-18
Data-Entry Screen—moves forward or backward within a dataor BACKWARD
entry space by pressing the FORWARD
keys to move forward or backward within the space.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the Nomad Handheld
Combination Keys
By pressing specific keys at once, or in a particular order, you can
execute a task quickly. Certain quick key tasks can be performed no
matter what type of screen is shown. The following table summarizes
tasks that you can perform using quick keys.
Press
once.
To turn off the Nomad.
To enter a reading or select an item
from a menu screen.
tR
Press
lo
Press
Press
To enter a decimal point. (This is
typically required only by “floating
point” meters.)
To return to the preceding screen.
Pi
To enter a space when entering a
special message or other data.
Press
To erase a letter, number, or
character that you have entered.
As you backspace over each letter,
number, or character, each is
erased.
Press
Press
To turn on the Nomad.
el
ea
Press and hold
for five
seconds, then release. Choose
Shut Down.
se
Use the color coding to remember which keys to use with quick keys that have
two functions: to activate the function printed in yellow, press the YELLOW
function button first and then press the key with a function printed in
yellow.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
To show meter information on the
screen.
4-19
Using the Nomad Handheld
Press
To minimize the amount of time the
backlight stays on and dim it to only
as bright as required to view the
display.
, PROGRAMS,
SYSTEM TAB,
Press
To perform a soft reboot of the
Nomad handheld.
then
se
Backlighting can drain the battery rapidly. To conserve the battery, use this
feature only in low light.
el
ea
If you do not press a key within 45 seconds of activating this feature, the
Nomad automatically deactivates the backlight to conserve battery power.
tR
Table 4.1 Nomad Functionality
Function
lo
Power ON
Pi
Power OFF
Turn backlight
ON/OFF
4-20
Press
once.
Press and hold
for five seconds, then
release. Choose Shut down.
Turn screen OFF
Reboot
Explanation
Press
once.
Press and hold
Hold down
Choose Reset.
for two seconds
for five seconds, then release.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the Nomad Handheld
Function
Explanation
Today
Press
to escape from any screen.
Tab
Press
screen.
to advance to the next field on the
Next and previous
account
Press
or
+ FORWARD
Next unread
tR
Resequence
lo
Reset order/
delete read
Previous menu/
back
Pi
el
ea
Previous unread
Press
se
BACKWARD
Field Programmer
Press
Press
Press
Press
, then
, then
Do one of the following:
•
Logged into route:
•
Tap
Not logged in route:
Tap
N_SIGHT R900 User’s Manual for the Neptune Handheld System
, then
, then
4-21
Using the Nomad Handheld
Function
Explanation
Data Logger
Do one of the following:
•
Logged into route:
•
Tap
Not logged in route:
Tap
Power on the R900 BCR by pressing
for two seconds on the R900 Belt Clip
Receiver.
el
ea
tR
, then
Do the following:
on the
Tap
Nomad.
Click
Select the Belt Clip in the drop-down selection list.
Click
Pi
lo
se
Bluetooth Pairing
(with the R900 Belt
Clip Receiver)
, then
Adjusting System Settings
System settings affect how the handheld displays and accesses data.
Although these settings are factory-set to meet the needs of most meter
reading processes, you can change some of the settings so that they
better suit your needs. These settings are typically set once and never
changed; however, you can adjust these settings any time.
4-22
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the Nomad Handheld
Calibrating the Stylus
The Nomad handheld has a touchscreen display that uses a stylus for
ease-of-use. Because each person’s touch differs, it is important to
calibrate the stylus to the touchscreen for the user’s own personal touch.
All functions are available without the stylus by using keyboard.
se
To calibrate the stylus, complete the following procedure.
On the N_SIGHT R900 Login screen, tap M or touch
Pi
lo
tR
el
ea
The N_SIGHT R900 Main Menu screen appears.
Figure 4.13 N_SIGHT R900 Main Menu
Press 6 or touch item
Press 9 or touch
Handheld.
Stylus.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
4-23
Using the Nomad Handheld
el
ea
se
The Stylus Calibration screen appears like Figure 4.14.
Figure 4.14 N_SIGHT R900 Stylus Calibration Screen
tR
Calibration is simply done by touching the center of the target with
the stylus for a couple of seconds and releasing. When the target
moves to another place, repeat the operation.
Press the stylus on the center of the target until it moves, and then
release.
lo
Pi
Once released the target moves to the next corner of the screen.
Remember just to touch the screen; there is no need to press hard or to
punch it.
4-24
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the Nomad Handheld
el
ea
se
The target moves to another location on the screen similar to that
illustrated in Figure 4.15.
Figure 4.15 Stylus at Another Location on Screen
When finished, press
lo
Repeat pressing the stylus on the center of the target until it moves,
and then release.
tR
Pi
The handheld returns to N_SIGHT R900 Main Login screen.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
4-25
Using the Nomad Handheld
Changing the Handheld Properties
The section allows you to adjust or change the following properties for
the handheld:
•
Key clicks
•
Reading entry direction
•
Route direction
Working with the Properties Screen
On any reading
entry screen, press
el
ea
se
To access the Properties screen, complete these steps:
on the
expandable keypad.
Pi
lo
tR
The Properties
screen appear as
illustrated in
Figure 4.16.
4-26
Figure 4.16 Handheld Properties Screen
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the Nomad Handheld
Changing the Reading Entry Direction
As you enter a reading in the handheld, each number can be displayed
from right to left or from left to right.
In the Read Dir field, touch the down arrow and do one of the
following:
•
Select LEFT TO RIGHT if you want the number to begin
from the left.
•
Select RIGHT TO LEFT if you want the number to begin
from the right.
se
These setting toggle between Left to Right or Right to Left
according to the current setting.
el
ea
This procedure affects only accounts whose directions have not been set by
the host computer. If the reading-entry direction of an account has been set
by the host computer, the host setting replaces your setting.
Changing the Route Read Direction
In the Route Dir field, touch the down arrow and do one of the following:
lo
tR
The handheld typically displays meters of a route from the first meter to
the last meter. However, you can change the order that meters are
displayed so that they are shown from the last meter to the first meter.
Pi
•
•
Select FORWARD if you want the readings to advance to the
next unread account in the route.
Select BACKWARD if you want to change the directions of
the readings to go backward to the previous unread account in
the route.
These settings toggles between Forward or Backward according to
the current setting.
Turning Key Clicks On and Off
The Key Clicks feature allows you to control how the handheld
responds when you press a key. When this feature is ON, the handheld
beeps whenever you press a key. Turning the Key Clicks feature on can
N_SIGHT R900 User’s Manual for the Neptune Handheld System
4-27
Using the Nomad Handheld
help you reduce errors by making sure that you press each key fully. If
you do not press a key fully, the handheld does not acknowledge your
entry. You can turn the Key Clicks feature on or off at any time.
Do one of the following:
•
Select the check box to enable Key Clicks.
•
Leave the check box empty to disable the Key Clicks.
These settings toggle between on (checked) or off (unchecked)
according to the current setting.
Touch OK to save your settings.
se
You return to the reading-entry screen or your previous screen.
el
ea
Configuring RF/Serial Properties
tR
Depending on the type of accounts on your route, you may have to
configure the RF antenna, the type of probe, or serial properties you are
using. Follow this procedure to configure or change the RF antenna, the
type of probe, or serial properties.
Press
Pi
lo
The System
Menu appears as
illustrated in
Figure 4.17.
Figure 4.17 N_SIGHT R900 F1 Menu
4-28
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the Nomad Handheld
Touch
el
ea
se
The System Menu
appears as illustrated
in Figure 4.18.
Figure 4.18 N_SIGHT R900 System Menu
Touch
tR
Pi
lo
The RF/Serial
Properties screen
appears as illustrated
in Figure 4.19.
Figure 4.19 RF/Serial Properties Screen
N_SIGHT R900 User’s Manual for the Neptune Handheld System
4-29
Using the Nomad Handheld
Turning On and Off the Nomad
This section explains how to turn the handheld on and off, and then how
to sign on to access the screens needed to complete meter reading tasks.
Whenever the handheld is in a communication cradle, it is on. This is
because, when connected properly, the cradle supplies power. However,
once the handheld is taken out of the cradle, the unit runs on its battery.
When powered by the battery, you can manually turn on the handheld
and you can turn it off automatically or manually.
el
ea
Turning the Nomad On
se
Use the following procedures to turn the handheld on or to turn it off
manually.
Turn on the Nomad Handheld by pressing and releasing the
button. The Nomad shows a menu, data-entry, or message screen
depending upon the last activity performed with the unit.
tR
One of the most convenient features is suspend/resume. There is no
waiting for the unit to boot up every time it is turned on. (This does not
occur the first time the unit is powered ON.)
Pi
lo
A message indicating low battery can appear on the battery LED located on
right side of the unit. For a new Nomad, be sure to connect the plug to the
power cord and attach to the power supply. The unit will be charged in about
4.5 hours. Neptune recommends that you fully charge the unit prior to your
first use.
Turning the Nomad Off
Manually turn off the handheld by pressing and holding down the
button for five seconds, then release. Choose Shut Down. The
display goes blank indicating that the handheld is off.
4-30
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the Nomad Handheld
If you allow the handheld to remain inactive for the factory-set delay of
45 seconds or for the delay time specified by the host computer, it turns
off automatically. After this period of inactivity, the screen of the
handheld goes blank and the unit turns off to conserve the battery. Just
tap the screen to use the Nomad again.
Logging In and Out of the N_SIGHT R900
This section explains how to log into N_SIGHT R900 on the handheld
to access the screens needed to complete meter reading tasks.
se
Logging Into N_SIGHT R900 on the Nomad
el
ea
After you have loaded a route, or after you have exchanged meter
readings and route data with the host computer, you need to log into
N_SIGHT R900 on the handheld. Signing on gives you access to the
screens you need to collect and exchange route and meter data.
Complete the following steps to log into N_SIGHT R900 on the
Nomad.
If you have not already done so, press
to turn on the Nomad.
tR
lo
If you see the message Not Uploaded, this means the handheld has
been loaded but has not yet been uploaded. This is normal if a new route was
just loaded to the handheld.
Pi
Touch
or Synchronize to start Communications. For more information,
refer to “Communicating with the Host Computer,” on page 7-1.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
4-31
Using the Nomad Handheld
You can see a message
like the one illustrated in
Figure 4.20.
Message area
el
ea
se
Version number
Figure 4.20 N_SIGHT R900 Message Area
Click
tR
Pi
lo
There may be times that the Clock Error screen appears when you are
attempting to log in. When this screen appears, continue with the following
steps.
4-32
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the Nomad Handheld
el
ea
se
A Clock Error screen
appears, prompting you to
log on and manually set
the clock, as illustrated in
Figure 4.21.
Figure 4.21 N_SIGHT R900 Clock Error Screen
Click Yes.
lo
tR
If you answer NO to the
clock error message, the
Login screen appears again.
Pi
After you click Yes, the
Set Date/Time screen
appears as illustrated in
Figure 4.22.
Figure 4.22 N_SIGHT R900 Set Date / Time Screen
N_SIGHT R900 User’s Manual for the Neptune Handheld System
4-33
Using the Nomad Handheld
If applicable, make any
changes to the date and
time.
The correct date and time
to use is the date and time
that the handheld last
synchronized.
When the date and time
are accurate, click OK.
el
ea
se
The Handheld Login
screen appears as
illustrated in Figure 4.24.
Figure 4.23 N_SIGHT R900 Handheld Login Screen
tR
The Reader ID field displays the information contained in the
N_SIGHT R900 system.
Complete the following information as applicable:
Pi
lo
•
4-34
Password (Determined by N_SIGHT R900 setup)
•
Vehicle # (Optional)
•
Mileage (Optional)
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Using the Nomad Handheld
Click
el
ea
se
The Select Route screen
appears as illustrated in
Figure 4.24.
Figure 4.24 N_SIGHT R900 Select Route Screen
Highlight the route you
want, and click OK.
tR
Pi
lo
A message appears
similar to the one
illustrated in Figure 4.25.
Figure 4.25 N_SIGHT R900 Initializing Message
N_SIGHT R900 User’s Manual for the Neptune Handheld System
4-35
Using the Nomad Handheld
When the software has finished initializing a Reading Entry screen
indicating that the sign on process is complete and that the unit is
ready for use in collecting readings. See Figure 4.26.
el
ea
se
For assistance in using
the Nomad to collect
meter readings, refer to
Figure 6 on Page 6-1.
tR
Figure 4.26 N_SIGHT R900 Reading Entry Screen
Logging Out of N_SIGHT R900
Pi
lo
The only time that you need to log out of N_SIGHT R900 on the
handheld is just before you begin exchanging information with the host
computer. Logging out gives you access to the communication features
of the handheld. Because logging out of N_SIGHT R900, instructions
for logging out on the handheld are included in the procedures that
describe how to exchange information with the host computer. For more
information, see “Exiting the Software,” on page 7-1.
If you allow the handheld to remain inactive for the factory-set delay of
45 seconds or for the delay time specified by the host computer, it turns
off automatically. After this period of inactivity, the screen of the
handheld goes blank and the unit turns off to conserve the battery.
4-36
N_SIGHT R900 User’s Manual for the Neptune Handheld System
5 Setting Up the R900 Belt Clip Receiver
R900 Belt Clip Receiver
el
ea
se
This section introduces you to the R900® Belt Clip Receiver
(R900 BCR). It will explain how the R900 BCR is incorporated into the
N_SIGHT R900 host software, and how it will be used by both meter
readers and operators. It will also help you become familiar with the
basic features and functions the handheld computer offers.
tR
This chapter provides basic instructions for unpacking and inspecting
the R900 BCR. It also gives instructions for setting up the R900 BCR,
becoming familiar with the display, pairing it with the handheld, and
usage.
R900 Belt Clip Receiver Overview
Pi
lo
The R900 BCR is a software-defined receiver capable of simultaneously
receiving R900, Advantage, and Pocket Pro Reader RF transmissions.
The R900 BCR collects readings and then transfers these readings to the
handheld through the Bluetooth connection. The R900 BCR also has the
capability to receive and store R900 readings that can be imported into
the billing system without the use of a handheld. Because the
R900 BCR is software-defined, you can apply firmware updates in
order to keep your R900 BCR current with new products introduced to
the market.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
5-1
Setting Up the R900 Belt Clip Receiver
Nomad Handheld and R900 Belt Clip Receiver
CIS/billing
software
el
ea
se
The Trimble® Nomad® (Nomad) handheld utilizes Bluetooth
connectivity to Neptune’s R900 BCR to receive the meter readings.
Field
data collection
hardware
Host
management
software
RF AMR
endpoint
tR
Figure 5.1 Meter Reading Cycle
Unpacking and Inspecting Equipment
lo
Besides using normal care, you need no special instructions to unpack
the handheld or the equipment that you purchased with it.
Pi
Check that you have received all the items you need for the type of
system configuration that you are using and inspect the items for
shipping damage. If you detect any damage, return the damaged
equipment to Neptune. Instructions for shipping the handheld to
Neptune are given in “Returning your R900 Belt Clip Receiver,” on
page 2-7 of this manual.
Save the packing box that was used to ship the handheld. Should you ever
need to ship the handheld, you need to repack the unit in its original shipping
box. The handling involved in land and air transport often subjects the
handheld to impact beyond that which occurs during normal use. The packing
box is designed to absorb shocks and protect the handheld device during
shipping.
5-2
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Setting Up the R900 Belt Clip Receiver
R900 Belt Clip Receiver Components
Figure 5.2 shows the basic components of the R900 BCR.
LEDs
Pi
lo
Power buttons
SD/USB
tR
Front view
el
ea
se
Battery door
Side view
SD card/battery door
Top view
Side view
Figure 5.2 R900 Belt Clip Receiver Components
N_SIGHT R900 User’s Manual for the Neptune Handheld System
5-3
Setting Up the R900 Belt Clip Receiver
Using the R900 Belt Clip Receiver
The following section explains how to use the R900 BCR.
Understanding the R900 Belt Clip Receiver Modes
el
ea
se
The following tables describe the R900 BCR modes of operation. You
change modes on the R900 BCR with a combination of the Mode and
Enter buttons. To cycle through available modes, you press the Mode
button. The Mode indicator will flash with the color for the mode to
enter. To enter the Mode, you press the Enter button within two seconds
of pressing the Mode button. If entered, the Mode indicator displays the
newly-entered mode. If you do not press Enter within two seconds, the
R900 BCR stays in the previous mode. This combination of Mode and
the Enter button is done to prevent accidental mode changes during
operation.
Table 5.1 R900 Belt Clip Receiver Power
Function
Pi
lo
tR
Power ON
Explanation
Press
for two seconds. The backlight turns
orange when the power is applied.
The unit takes approximately one minute to fully
boot. The Mode and RF lights are white during
most of boot-up. The unit is fully booted when the
Mode and Enter light turn off and the Mode LED
displays the previous mode of operation
Power OFF
Press
for two seconds.The mode and RF
lights blink until off.
Setting Date/Time
5-4
The R900 BCR synchronizes the time with the
Nomad when the two are paired. The time on the
R900 BCR defaults to the time from the last
Nomad synchronization.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Setting Up the R900 Belt Clip Receiver
Table 5.2 R900 Belt Clip Receiver Modes
Function
LED Color
Explanation
Reading Modes
Normal
(Green)
Normal Mode is used to connect through Bluetooth to
a host device. Selection between Route (filtered) and
RF Test (unfiltered) is made in the host device
software.
se
To enter this mode from other modes.
MODE
Press
until the Mode LED flashes green.
el
ea
ENT
(Yellow)
, and the Mode LED turns green.
Unfiltered Operations Mode can operate using the
battery or when connected to vehicle power.
tR
Unattended
Press
Pi
lo
To enter this mode with battery power:
MODE
Press
until Mode LED is yellow.
ENT
Press
continued on next page
N_SIGHT R900 User’s Manual for the Neptune Handheld System
5-5
Setting Up the R900 Belt Clip Receiver
Table 5.2 R900 Belt Clip Receiver Modes
Function
LED Color
Explanation
To enter from when connected to vehicle power:
MODE
Press
until the Mode LED is yellow.
ENT
Press
and release.
se
ENT
Press
release.
again and hold for five seconds, then
el
ea
The Mode LED is Magenta.
Connect the USB.
(White)
Pi
lo
USB mass
storage
tR
The USB charger must be capable of suppling 1A of
current.
The SD card appears as an external drive to the PC.
To enter this mode:
1 Connect the USB to the R900 BCR and to the PC.
The USB must be connected before the unit can enter
the USB mass storage mode.
MODE
2 Press
until Mode LED flashes white.
ENT
3 Press
The SD Card now shows as an external drive
attached to the PC.
5-6
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Setting Up the R900 Belt Clip Receiver
Accessing the R900 Belt Clip Receiver Status Screen
The R900 BCR must first be set to Normal Mode to access the
R900 BCR Status screen. The following tables explains how to access
the status screen on the handheld.
Table 5.3 R900 Belt Clip Receiver Software Functions
Accessing R900 Belt Clip Receiver Status Screen
While in route
Neptune Key, System, UTILS, AMR Status =
Select Advanced Options.
Select the check box.
Select Belt Clip Status.
el
ea
TAB twice, UTILS, Belt Clip Status =
Select
Select 5 Utils.
Select
Belt Clip Status.
Pi
lo
, 5 ,
Click
tR
From the
Synchronize
screen
se
, 8 , 2 ,
N_SIGHT R900 User’s Manual for the Neptune Handheld System
5-7
Setting Up the R900 Belt Clip Receiver
Understanding the R900 Belt Clip Receiver LED Operating Modes
To help you better interpret the different colors for the flashing Mode
LED, refer to the following table.
Table 5.4 R900 Belt Clip Receiver LED Operating Modes
State
LED Colors
Unit powered OFF
No color; LEDs off.
se
Power
Green
On-Battery 30% – 16%
Yellow
On-Battery 15% – 6%
On-Battery 5% – Critical
lo
Mode
Red
Flashes red
tR
Battery – Charging
el
ea
On-Battery 100% – 31%
Flashes yellow
Green
Unattended mode
Yellow
Installed mode
Magenta
Mass storage mode
White
Pi
Normal mode
continued on next page
5-8
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Setting Up the R900 Belt Clip Receiver
Table 5.4 R900 Belt Clip Receiver LED Operating Modes
State
LED Colors
RF Mode
Off
Receive R900/ERT packet
Flashes green when receiving
Receive Advantage packet
Flashes cyan when receiving
No reading received in two + minutes
Solid red
el
ea
Bluetooth
Off
tR
Not Connected
Pairing
Flashes blue
Blue
Pi
lo
Connected
se
No reading being received
Error Codes
Temperature error
Bluetooth and Power LED flash red five times
Hardware error
Bluetooth and Power LED are solid red
Battery error
Power LED flashes red and yellow
Cannot power on - battery too low
Power LED flashes red three times
SD card error
Mode LED is solid red
N_SIGHT R900 User’s Manual for the Neptune Handheld System
5-9
Setting Up the R900 Belt Clip Receiver
Understanding the External Battery Charger Status
Refer to the following table for a description of the external battery
LED.
Table 5.5 External Battery Charger LED
LED
Indicates
Startup initialization when applying power
OFF
No battery inserted
Yellow
Battery charging
se
Red, yellow, green or
OFF
Solid green
Error condition
el
ea
Red
Battery charged successfully
Pairing the Trimble Nomad to the R900 Belt Clip Receiver through the Bluetooth
tR
Complete these steps only if you are pairing the Nomad to the
R900 BCR for the first time.
Pairing the Trimble Nomad
To pair the Nomad to the R900 BCR, complete the following steps.
Power ON the R900 BCR and set to Normal Node, if not already
set. See “Understanding the R900 Belt Clip Receiver LED Operating Modes,” on page 5-8.
Pi
lo
On the Nomad, click
Click
Click
– UTILS.
– Belt Clip Status.
The AMR Connection screen appears. The R900 BCR is visible in
the Broadcasting Device drop-down selection list.
5-10
Choose the device from the drop-down selection list and click
Bluetooth.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Setting Up the R900 Belt Clip Receiver
The R900 Belt Clip Receiver Status screen now displays the device
details.
•
If you have previously paired a device, go to the R900 BCR
Status screen and not the AMR Connection screen.
•
If you want to Change Devices, you can click this option on
the bottom of the R900 BCR Status screen.
You then see the AMR Connection screen and can choose the
device from the drop-down selection list.
Using the R900 Belt Clip Receiver to Read a Route
el
ea
se
To begin reading a route using the R900 BCR, you first need to load a
route to the Nomad. See “Loading and Unloading Data for Handhelds”
in the N_SIGHT™ R900® Online Help.
Click
to load a route when you are working in the N_SIGHT
R900 host software.Press F1 to see the instructions for loading a route to a handheld.
tR
Once the route is loaded and the pairing is complete, you can log in and
the unit can receive readings from the R900 BCR.
R900 Belt Clip Receiver Status Screen in N_SIGHT R900
Pi
lo
While the Nomad and the
R900 BCR are paired, you
can access a screen showing
the status of the R900 BCR.
You can see a message like
the one illustrated in Figure
5.3.
Figure 5.3 R900 Belt Clip Receiver Status Screen
N_SIGHT R900 User’s Manual for the Neptune Handheld System
5-11
Setting Up the R900 Belt Clip Receiver
The following information appears on this screen.
Connection
Displays the type of connection used to pair
the R900 BCR, such as Bluetooth
Device
Displays the name of the R900 BCR
Temperature
Displays the temperature of the R900 BCR,
such as normal.
SD MEM Free
Displays the amount of available memory
for the SD card.
Date
Displays the date and time as follows:
Displays the version of the firmware on the
R900 BCR
el
ea
Firmware
Battery
Date: MM/DD/YYYY
Time: HH:MM
se
•
•
Displays the available battery percentages
Allows you to change the reading mode for
the R900 BCR by clicking the drop-down
selection list.
•
•
•
Efficiency –reduced RF performance
and best battery life
Moderate – default RF performance
Performance – best RF performance
and decreased battery life
lo
tR
RF Mode
Pi
RF Performance Modes
This Mode can be changed from the R900 BCR Status screen. The unit
has three options for the RF performance during a reading:
Efficiency
Reduces RF performance* and best battery
life
Moderate
Default RF performance*
Performance
Best RF performance* and decreased
battery life
*RF performance refers specifically to the throughput of the receiver
which can impact the speed with which readings are processed in
high density areas. Range is not impacted by these modes.
5-12
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Setting Up the R900 Belt Clip Receiver
Selecting the R900 Belt Clip Receiver Reading Mode
To choose the reading mode, complete the following steps.
On the Nomad, click
Click 5
Click
– Utilities.
– R900 Belt Clip Receiver Status.
The R900 Belt Clip Receiver Status screen appears.
Tap the drop-down selection list for RF Mode and you can choose
the reading mode. See the modes listed above.
se
el
ea
Using the R900 Belt Clip Receiver RF Test Mode
RF Test Mode allows the R900 BCR to go into a continuous receive
mode and listens for any and all R900 transmissions.
tR
From the Login Screen
To access RF Test Mode from the
Login screen, complete the
following steps.
On the Nomad, click
lo
Pi
Click 5
– Utilities.
Click
– RF Test.
The RF Test Mode screen
appears as illustrated in Figure
5.4.
Figure 5.4 R900 Belt Clip Receiver RF Mode Screen
N_SIGHT R900 User’s Manual for the Neptune Handheld System
5-13
Setting Up the R900 Belt Clip Receiver
From the Route Screen
To access RF Test Mode from
the Route screen, complete the
following steps.
In the route, click
Click 8
– System.
Click 2
– Utilities.
Click
– RF Test.
se
el
ea
The RF Test Mode screen
appears as illustrated in Figure
5.4.
Figure 5.5 R900 BCR RF Mode Screen from Route
R900 Belt Clip Receiver SD Card Functionality
tR
Any data that is read by the R900 BCR and sent to the handheld is
stored on its internal SD card.
Pi
lo
The SD card also handles the firmware updates explained in “Using the
R900 Belt Clip Receiver,” on page 5-4.
5-14
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Setting Up the R900 Belt Clip Receiver
Updating R900 Belt Clip Receiver Firmware
You cannot update multiple R900 BCRs at once; they must be updated individually.
se
When there is an update to the R900 BCR firmware, it is available from
Neptune through the web updates in the N_SIGHT R900 software, or it
can be obtained from Neptune Customer Support through email or direct
upload to an FTP site.
el
ea
With either choice for receiving the firmware update; the firmware is
updated in the N_SIGHT R900 database and then sent to the R900 BCR
through the USB transfer cable or saved to the SD card and installed on
the R900 BCR.
tR
To update the R900 BCR firmware update with the USB cable, the R900 BCR must
first be connected to the PC and be in Mass Storage Mode. To update through the SD
Card, the Firmware Update File can be transferred to the SD card by using an SD Card
Reader
To update the R900 BCR firmware, complete the following steps.
Connect the R900 BCR to the PC and place in Mass Storage Mode.
lo
In the N_SIGHT R900 host software, select Utilities.
Pi
Select the Beltclip Firmware tab.
Figure 5.6 Tab within N_SIGHT R900 Utilities
N_SIGHT R900 User’s Manual for the Neptune Handheld System
5-15
tR
el
ea
se
Setting Up the R900 Belt Clip Receiver
Figure 5.7 R900 Belt Clip Receiver Firmware Tab with Update Options
Pi
lo
The Web Update and Local File buttons perform the same task of updating the
database with the updated firmware version depending on where the updated
firmware file is located.
How the Firmware Update Works
The following explains how the firmware update works.
Web Update—looks to the Neptune servers for an updated version of
R900 BCR firmware and downloads it to the database
Local File—allows you to import updated firmware from a thumb
drive, network drive, or FTP site into the database
Belt Clip Update—locates the updated firmware file after the updated
firmware has been downloaded and sends it to the R900 BCR through
the USB transfer cable
5-16
N_SIGHT R900 User’s Manual for the Neptune Handheld System
6 Gathering Route Data
se
This chapter provides instructions for using the handheld to collect
meter readings and route data. The procedures in this chapter assume
that route assignments have already been loaded onto the handheld.
Pi
lo
tR
el
ea
When using this chapter, keep in mind that a sample reading-entry
screen is shown throughout the manual. The reading-entry screen of
your handheld may not resemble the one shown here. This
inconsistency is caused when the N_SIGHT R900 operator customizes
the screen so that it better suits the needs of your company.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
6-1
Gathering Route Data
The Reading Entry Screen
The following illustration shows the N_SIGHT R900 Reading Entry
screen.
Icon bar
Meter number
Account number
el
ea
Location in route
se
Read entry
Figure 6.1 N_SIGHT R900 Reading Entry Screen
Pi
lo
tR
Status of account
(UR = unread)
6-2
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Gathering Route Data
Manually Collecting Meter Readings
When using the CE5320 to collect meter readings, typically you need to
enter only the reading for each meter. However, sometimes you may
need to also enter a trouble code or comment concerning conditions at
the account. Additionally, you may “skip” an account by inserting a
“skip code” and indicating why you skipped the account. The
procedures in this topic give you the information you need to manually
collect or skip readings:
“Entering a Reading,” which follows
•
"Entering a Skip Code" on page 5
•
"Entering Comment Codes" on page 7
•
"Adding Free-Form Notes" on page 9
el
ea
se
•
Entering a Reading
tR
Follow this procedure to enter a meter reading in the handheld.
Pi
lo
If this is the first time that you have accessed a route, the reading-entry
screen of the first meter in the route appears in the display. If the read
, “Left to Right,” then after the reading for the first
direction is set for
meter is taken the screen advances to the second meter in the route. By
clicking this icon, you can change the read direction to
, “Right to Left.”
The read direction toggles between these two read directions.
If you have not already done so, first log into N_SIGHT R900 on
the handheld, so that a reading-entry screen is appears in the display. See Figure 6.1 on Page 6-2.
For help with this task, refer to “Logging Into N_SIGHT R900 on
the CE5320,” on page 3-26 or “Logging Into N_SIGHT R900 on
the Nomad,” on page 4-31.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
6-3
Gathering Route Data
Using the number keys, enter the reading in the space provided.
el
ea
se
Reading entry field
tR
Figure 6.2 N_SIGHT R900 Reading Entry Field
lo
The number of hyphens in the reading entry field indicate the number of
reading digits required.
Pi
Touch
or press
The N_SIGHT R900 software displays the next meter in the route,
according to the route direction
or
. Touching this icon and
temporarily change the direction for the route. However, to change
it for future uses, refer to the procedure for “Changing the Route
Direction, Forward or Reverse,” on page 6-14.
Continue entering readings for each meter until you have completed all routes assigned to you.
As you complete each route, a message appears in the display to let
you know that you have completed the route and are moving to a
new one. Follow the instructions shown in the display to access the
reading-entry screen of the next route.
6-4
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Gathering Route Data
Entering a Skip Code
In some cases, you may be unable to collect a reading. If you are unable
to collect a reading, you can enter a skip code, giving the reason that the
reading could not be obtained.
Follow this procedure to enter
a skip code instead of a
reading.
From the reading-entry
screen of the meter for
which you want to enter a
el
ea
se
In the V4 file format, screens can appear differently depending on the file format you
are using. For example, you could have either Coded Notes or Comment Codes.
tR
skip code, press
on
the CE5320 keypad or the
Nomad screen keypad.
Pi
lo
A screen appears
prompting you to enter a
skip code in place of the
reading. See Figure 6.3.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Figure 6.3 N_SIGHT R900 Skip Order Screen
6-5
Gathering Route Data
Click the drop-down selection list as illustrated in
Figure 6.4 to choose the
appropriate reason code.
el
ea
se
Figure 6.4 N_SIGHT R900 Skip Order Reason Codes
The actual codes that are available to you are determined by the
host operator.
In Comment, type
any notes for this
account.
Click Skip.
Pi
lo
tR
The account is
marked as
skipped, as
illustrated in
Figure 6.5. The
N_SIGHT R900
software displays
the next meter in
the route.
Skipped
read
Figure 6.5 N_SIGHT R900 Skipped Read
6-6
Continue entering readings within this route.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Gathering Route Data
Entering Comment Codes
In the V4 file format, screens can appear differently depending on the file format you
are using. For example, you could have either Coded Notes or Comment Codes.
From the reading-entry
screen of the meter for
which you want to enter a
el
ea
se
In some cases, you may need to enter a comment code (a coded note) for
trouble or another reason for a meter. For example, if the glass is broken
or the seal is broken, the meter is leaking or frozen, or has a bad dial. If
you notice trouble while collecting a reading, you can enter a trouble
code. Follow this procedure to enter a trouble code.
trouble code, touch
Pi
lo
tR
A Coded Notes screen
appears prompting you to
enter coded notes. See
Figure 6.6.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Figure 6.6 N_SIGHT R900 Coded Notes Screen
6-7
Gathering Route Data
Touch the DOWN
arrow to view the list of
codes, as illustrated in Figure 6.7.
Select the appropriate
code for the trouble found.
Select one or two additional codes, if applicable.
el
ea
se
Figure 6.7 Drop-down Selection List of
Coded Notes
Touch
to save the
trouble codes associated
with the meter.
Marked Comment Code
tR
1.
Pi
lo
The icon changes to
, as illustrated in
Figure 6.8 to show that
there is a comment code
attached to this account.
This works as a toggle.
Figure 6.8 N_SIGHT R900 Comment Code
6-8
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Gathering Route Data
To view the trouble codes
entered for this account,
click the red icon.
Click
Route.
Continue entering readings within this route.
el
ea
se
to return to the
Figure 6.9 Viewing Comment Codes
tR
Adding Free-Form Notes
Pi
lo
Note to Pat! After you load the V2 format, this changes to Customer Notes and the
appearance also change.
In some cases, you might want to add some free-form notes to inform
your office about a change to an account. When the N_SIGHT R900
operator uploads data from your handheld, your message is sent to the
N_SIGHT R900 host software and may also be sent to your company’s
billing computer. You can also use this feature to create reminders for
yourself. For example, you might use this feature to specify the exact
location of a meter. Follow this procedure to enter a special message.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
6-9
Gathering Route Data
From the reading entry
screen of the meter for
which you want to enter
free-form notes, press
Touch
el
ea
se
A screen appears
prompting you to enter a
free-form notes. See
Figure 6.10.
Figure 6.10 N_SIGHT R900 Free Form Notes Screen
Begin typing your note in the first blank line.
At the end of the line, tab to the second line to continue.
tR
When you’ve completed your notes, touch
Pi
lo
6-10
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Gathering Route Data
Leaving a Reading Blank
In some cases, you need to leave a reading blank. For example, if a
meter’s reading is to be estimated by your company’s billing computer.
Follow this procedure to skip over a meter without entering a reading or
a skip code.
Access the reading entry screen of
the meter you
want to skip.
Figure 6.11 Leaving a Meter Reading Blank
Using the direction keys, press the FORWARD
lo
tR
el
ea
se
Blank
read
or BACKWARD
Pi
key to display the next meter in the route without entering a
reading.
Your ability to use this feature can be restricted by your company. In such
cases, the handheld will inform you that you must enter either a reading or a
skip code.
The next meter in the route appears in the display.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
6-11
Gathering Route Data
Collecting RR Readings
When you receive your Neptune handheld, it is factory-set to collect
readings manually using the keyboard. When you begin readings
manually, the handheld screen appears similar to the one illustrated in
Figure 6.12.
el
ea
Figure 6.12 N_SIGHT R900 Manual Reading Screen
Pi
lo
tR
Manual
entry
se
Manual keyed read
While on a keyed account or an R900 account the handheld reads R900s
within range, holds these reads in a buffer, and distributes them to the correct
accounts in the route once an R900 account appears on the display.
6-12
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Gathering Route Data
Collecting an RF Reading
When you approach an RF account while collecting meter readings on a
route, the screen similar to the one illustrated in Figure 6.13 appears.
RF read; If current account is
R300, R3 displays.
357 FOREST COURT
tR
el
ea
se
RF entry
lo
Figure 6.13 N_SIGHT R900 RF Reading Screen
Pi
While on a Keyed account or an R900 account, the handheld collects R900
meter readings in the background.
If the account you are reading is an R900 account, the reading icon
at the top right of the screen displays as R9. If the account is an R300
account, the reading icon displays as R3. See Figure 6.13.
At an RF account, the unit is ready to receive a reading transmitted from
an RF transmitter, like an R900. If the account is set up properly and the
RF transmitter is transmitting properly, you should receive a reading for
the account once you are in range of the transmitter.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
6-13
Gathering Route Data
Working with Accounts
While you are reading meters and when you are working with accounts,
there are certain tasks that you need to perform to help you with your
data collection.
Changing the Route Direction, Forward or Reverse
Right route direction icon
Pi
lo
tR
el
ea
On the Reading
Entry screen, click
se
This icon is used for changing the Route Direction from a Forward
direction (advancing from account 1 to account 2) to reverse direction
(advancing from account 2 to account 1) as readings are being recording
in the handheld.
Figure 6.14 Left to Right Route Direction Icon
6-14
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Gathering Route Data
The icon changes to
as illustrated in Figure
6.15. This works as a
toggle between the two
read directions, forward
and reverse.
el
ea
se
Left route direction icon
Figure 6.15 Right to Left Route Direction Icon
tR
Tagging an Account
Pi
lo
While you are reading meters, there may be a need to tag an account and
come back to it later. Follow this procedure to tag or untag accounts
within the route for which you want to complete the readings later on.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
6-15
Gathering Route Data
On the Reading
Entry screen, do
one of the following:
•
Click
Tag account icon
or
Press
tR
el
ea
se
•
Figure 6.16 Tag Account Icon
Tag icon
Pi
lo
The icon changes to
as illustrated in Figure
6.17. This works as a
toggle between tagged
and untagged accounts.
Figure 6.17 Tagged Account
6-16
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Gathering Route Data
Continue entering readings within this route.
To search the tagged accounts so that you can complete the readings
for them, press
Finding Information
el
ea
se
When you are reading meters and need to find an account, an address, a
meter number, or some other information, you can easily do so by using
the N_SIGHT R900 Find function. If you already know specific
information about a meter, such as its meter number, you can quickly
display that meter by using the search function. When you use the
search feature, the handheld searches for the specific information that
you enter. When the software finds a meter whose data matches the
information you entered, that meter appears in the display. Follow this
procedure to find the information you need.
On the Reading Entry screen, press
Pi
lo
tR
The Find Order
screen appears as
illustrated in Figure
6.18.
Figure 6.18 N_SIGHT R900 Find Order Screen
N_SIGHT R900 User’s Manual for the Neptune Handheld System
6-17
Gathering Route Data
Touch
el
ea
se
The list of fields
displays for you to
select the type of
information you
want to find. See
Figure 6.19.
Figure 6.19 Search Display Fields
Select Multiple to
enter more than one
value for the search.
See Figure 6.20.
Pi
lo
tR
Figure 6.20 Search Screen Enter Multiple Values
6-18
N_SIGHT R900 User’s Manual for the Neptune Handheld System
el
ea
se
Gathering Route Data
Figure 6.21 Search Screen Multiple Values to Match
Touch the field for the information you want to find.
Your selection appears in the field.
Type a value for the information you want to find in the Value field,
if applicable.
tR
Pi
lo
You can find information within only the current route, or within any of the
routes you selected when you logged into N_SIGHT R900. The field named
Display Fields are typically where your address information is located. Use
Display Fields as your address search field.
If you selected more than one route when you logged into
N_SIGHT R900, do one of the following:
•
Touch Only Current Route if you only want to search within
the current route to find the information.
•
Leave the Only Current Route checkbox empty if you want
to search within all the routes you selected when you logged
into N_SIGHT R900.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
6-19
Gathering Route Data
Touch one of the following to begin your search.
•
Search> if you want to search forward in the route
•
” that appears on a display, indicating that the computer is waiting for the operator to enter information. Once the computer has
displayed a prompt, it waits for you to enter some information. Generally, it will
wait forever, but some programs have built-in time-outs that cause the program to continue after it has waited a specified amount of time.
tR
el
ea
se
operating system
Keys that allow you to execute a task quickly by pressing specific keys at once
or in a particular order.
A specific type of DATA-ENTRY SCREEN used by the handheld. The readingentry screen is used to enter readings.
Pi
reading-entry screen
lo
quick keys
read-type code
An arrangement of up to four numbers, letters, or both numbers and letters
that explain how the reading is obtained. For example, a code of “r0” might be
used to indicate that the reading is entered manually. See also code tables.
region code
In the N_SIGHT R900 APPLICATION PROGRAM, region codes are used to indicate the regional headquarters for a field office or to indicate the employees of
a regional headquarters. Region codes can be two digits, two letters, or a digit
and a letter.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
G-5
Glossary
A free-form statement sent from N_SIGHT R900 operators to the handheld
computers of meter readers assigned to a specific route. A route message can
contain as many as 80 characters. Compare with broadcast message and
survey message.
router
One of the most commonly used devices to connect several handheld at a
time. The router device allows you to connect as many communication cradles
to the HOST COMPUTER. Because the router provides communication connections for the cradles, whenever a handheld is placed in a communication cradle, it is ready to exchange data with the HOST COMPUTER.
screens
The graphic portion of a display. N_SIGHT R900 uses three different types of
screens to present the information shown in the display: a MENU SCREEN, a
DATA-ENTRY SCREEN, and a MESSAGE SCREEN.
select
To choose an item by using the arrow keys or by using a HOTKEY. N_SIGHT
R900 indicates that an item is selected by highlighting the item. See also
highlighted.
sequence number
A number assigned to each meter indicating the location of the meter in relation to other meters in the route. For example, a sequence number of 000003
indicates that the meter is the third meter of a route. The meter reader may
change the sequence number on the handheld computer, indicating a preferred placement of that meter within the route.
tR
Pi
sign on
lo
sign off
el
ea
se
route message
G-6
The act of exiting the meter reading portion of the handheld APPLICATION PROGRAM. By exiting the meter reading portion, you can access the communication function and send information to or receive information from the HOST
COMPUTER.
The act of accessing the meter reading portion of the handheld so that you
can obtain route assignments or collect readings.
skip code
An arrangement of up to four numbers, letters, or both numbers and letters
that explain why a reading was skipped. For example, a code of “s1” might be
used to indicate that a reading was skipped because the glass of the meter
was fogged and the meter reader could not see the usage display. See also
code tables
skip route
A route made up entirely of meters for which readings were attempted but
could not be obtained. For example, the glass on the meter may have been
fogged and the meter reader could not see the usage display. Compare with
blank route.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Glossary
survey message
A free-form question sent along with assigned routes to the handheld of a specific CYCLE. A survey message can contain up to 40 characters. Compare with
broadcast message and route message.
synchronize
The process of communications to send readings and route data to and from
the handheld and the HOST COMPUTER.
tag
A handheld feature that allows you to tag one or more meters in a route and
then have the handheld display only the tagged meters.
tag indicator
An icon
that appears in the display of the handheld to indicate that the
is hidden.
se
meter is tagged. When this symbol appears, the
An arrangement of up to four numbers, letters, or both numbers and letters
that explain why there is trouble with a meter. For example, a code of “t10”
might be used to indicate that the battery of a meter is low. See also code
tables.
upload
The process of sending readings and route data from the handheld to the
HOST COMPUTER.
user ID
An identifier that is assigned to each user of the handheld. Entering a user ID
number when you LOG IN ensures that only someone with a user ID can use
the handheld. A user ID can contain up to ten digits, ten characters, or a combination of ten digits and characters There can be no spaces in a user ID.
tR
lo
workstation
Microsoft Windows OPERATING SYSTEM. Windows supports 32-BIT and 64-BIT
applications, which means that application programs written specifically for
these operating systems run much faster.
A type of computer used for engineering applications, desktop publishing, software development, and other types of applications that require a moderate
amount of computing power and relatively high quality graphics capabilities.
Like personal computers, most workstations are single-user computers. However, workstations are typically linked together to form a LOCAL-AREA NETWORK,
although they can also be used as stand-alone systems.
Pi
Windows
el
ea
trouble code
In networking, workstation refers to any computer connected to a local-area
network. It could be a workstation or a PERSONAL COMPUTER.
N_SIGHT R900 User’s Manual for the Neptune Handheld System
G-7
Glossary
Pi
lo
tR
el
ea
se
Notes:
G-8
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Index
battery
charger 9-4
for CE5320 charger 3-6
Nomad cable 4-6
battery error 5-9
battery recharge contacts 2-6, 2-11
battery status indicators
color of 9-3
described 2-5, 2-10
illustrated 9-3
location (illus.) 2-5, 2-10
using 9-3, 9-15
beepers, described 2-7, 2-12
bits, defined G-1
BKSP key 3-19, 4-19
blank readings, entering 6-11
blank routes
See also skip routes
defined G-1
blue keys
function 3-19, 3-20, 4-19 to 4-20
using 3-13
bluetooth, LED 5-9
bookmarks, problems with 10-5
broadcast messages 3-27, 4-32, 5-11
See also route messages, survey messages
defined G-1
browse key 3-17, 4-17
button, mouse 8-20
Pi
lo
tR
B key 3-16, 4-16
backward keys
illustrated 3-15, 4-12, 4-18
base pressure A-1
batteries
calibrating 9-5, 9-8
charging 9-3
checking status of 9-3, 9-15
compartment (illus.) 9-9, 9-10
conserving 3-20, 4-20
described 2-6, 2-11
life of 9-5
low charge warning 4-30
ordering replacement 9-18, 9-21, 9-25 to 9-27
recharging 9-5
replacing 9-9 to 9-10
status indicator (illus.) 9-3, 9-15
using 4-30
el
ea
se
A key 3-16, 4-16
access
reading mode 5-13
RF test mode 5-13
access Codes menu 3-16, 4-16
actual gear ratio A-1
add, gas format 8-44, 8-47
adding
meters to routes 6-29
adding meters to routes 6-28 to 6-29
alphanumerics
defined G-1
AMR mode key 3-16, 4-16
application programs
defined G-1
atmospheric pressure A-1
audit failed error message 6-21
auto increment 8-31
automatic off
described 2-7, 2-12
automatic return
described 2-7, 2-12
C key 3-16, 4-16
cable 4-6
charger 4-4
for Bulverde charger 3-4
cable, USB transfer 5-17
calibrating, battery 9-5, 9-8
CE5320
features 2-4, 2-8, 2-13
illustrated 2-4
keyboard 2-4
CE5320, charger 3-3, 3-4, 3-6
central processing units, defined G-1
change modes, R900 BCR 5-4
N_SIGHT R900 User’s Manual for the Neptune Handheld System
I-1
Index
6-39, 6-41
Pi
lo
tR
code tables, defined G-1
codes, see specific code
Codes key 3-16, 4-16
Codes menu, key 3-16, 4-16
collecting meter readings 6-3
color-coding, on keyboard 3-15, 3-19, 4-19
colors, of battery status indicator 9-3
command gas 8-24
communication cradles
as part of system 3-2
defined G-2
with cradle-charging kit 3-3, 4-3
communication methods 7-1, 8-29, 8-40
company codes, defined G-2
components, R900 BCR 5-3
confirmation, off/Level1 8-31
connect to receptacle 8-29
connect, wiring 8-29
connecting
communication cable (illus.) 3-7
multiple devices 3-8
power cable to device (illus.) 3-6, 4-6
power supply 3-5, 4-4
router 3-5, 3-8, 4-5
I-2
constants, defined G-2
conventions, used in the manual 1-1 to 1-2
correcting
See also changing
meter information 6-30, 6-32
CPUs, see central processing units G-1
cradle and charging kits
illustrated 3-3 to 3-4, 4-3 to 4-4, 9-15
with communication cradle (illus.) 3-4, 4-4
create format 8-36
custom formats 8-29
customer support 1-5
cycles, defined G-2
se
damage
inspecting for 3-2, 4-1
repairing instructions 9-4
damage, inspecting for 5-2
data-entry screens
defined G-2
described 2-14, 2-16
example (illus.) 2-14
decimal
entering points 3-19, 4-19
using key 3-19, 4-19
default settings, defined G-2
delete
gas format 8-50
ProRead format 8-35
description of
automatic off 2-7, 2-12
automatic return 2-7, 2-12
batteries 2-6, 2-11
battery status indicators 2-5, 2-10
character keys 3-15
communication ports 2-5, 2-10
data-entry screens 2-14, 2-16
direction keys 3-15, 4-12, 4-18
displays 2-14
function keys 3-13
handstraps 2-6
hot keys 3-14, 4-13
information keys 3-16 to 3-18, 4-16 to 4-18
keyboard backlights 2-4, 2-10
el
ea
changing
keyboard click setting 3-24, 4-27
keyin direction 6-14
meter information 6-30 to 6-32
route direction 3-24, 4-27
character keys
defined G-3
described 3-15
characters, entering 3-13, 3-15 to 3-16
charger
battery 9-4
cable 4-4
CE5320 3-3, 3-4, 3-6
CE5320 cable 3-4
Nomad 4-3
Nomad battery 4-5, 4-6
Nomad illus. 4-3
Nomad 4-4, 4-5, 4-6
charger, CE5320 battery 3-6
checklist 8-27
clearing readings and skip codes 6-22, 6-24, 6-26,
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Index
se
electromagnetic resistance 2-7, 2-13
e-mail, customer support 1-6
ENTER key 3-19, 4-19
entering
blank readings 6-11
characters 3-15 to 3-16
decimals 3-19, 4-19
letters 3-15 to 3-16
skip codes 6-5 to 6-6
entry key 3-17, 4-17
error codes, LEDs 5-9
error messages, see also troubleshooting
ethernet ports, described 2-5, 2-10
exchanging information
methods of 8-40
exchanging information, see also sending and
receiving information
exchanging information, methods of 7-1, 8-29, 8-40
export, defined G-2
exposure, to temperatures 2-7
Pi
lo
tR
el
ea
description of (continued)
keyboards 2-4, 2-9
letter keys 3-15
main screens 2-14 to 2-15
menu screens 2-14, 2-15
message screens 2-17
meter reader tasks 2-3
meter readers 1-7
number keys 3-14, 4-12
operator tasks 2-3
operators 1-7
quick keys 3-19, 4-19
devices
connecting 3-5, 4-5
defined G-6
direction keys
defined G-2
described 3-15, 4-12, 4-18
displaying
bookmarked meters 3-19, 4-19
meter information 2-18, 3-19, 4-19
meters 3-15, 4-12, 4-18
meters of a route 2-18, 3-15, 4-12
reading-entry screens 2-17, 2-19, 3-15, 4-12, 6-33
route information 2-18
screens 2-17 to 2-21
displays
defined G-2
described 2-14
problems with 10-2, 10-3 to 10-4, 10-5
down keys, illustrated 2-15, 3-15, 4-18
downloading
defined G-2
problems with 10-6
downloading information
See sending and receiving information
drive A-1
edit
gas format 8-44
ProRead format 8-32
Edit key 3-16, 4-16
efficiency 5-14
efficiency, performance 5-12
F key 3-17, 4-16
F1 key 3-13
F2 key 3-13
F3 key 3-13
F4 key 3-13
F5 key 3-13
fax, customer support 1-6
features
automatic off 2-7, 2-12
automatic return 2-7, 2-12
battery 2-6
battery recharge contacts 2-6
battery status indicator 2-5, 2-10
beeper 2-7, 2-12
CE5320B 2-4, 2-8, 2-13
display 2-4, 2-9
handstrap 2-6
keyboard 3-11, 4-9
keyboard backlight 2-4, 2-9
LEMO communication port 2-5, 2-10
manual off 2-7, 2-12
optical-infrared port 2-6, 2-11
Find key 3-17, 4-16
N_SIGHT R900 User’s Manual for the Neptune Handheld System
I-3
Index
lo
Pi
G key 3-17, 4-16
Gas
preferences 8-41
gas
command 8-24
preferences 8-40
program 8-18
program register 8-40
readings 8-26
gauge pressure A-1
GBs, defined G-3
gear ratio, actual A-1
GoTo key 3-17, 4-16
I-4
el
ea
se
handhelds
dropping 2-8, 2-13
durability 2-7, 2-12
illustrated 2-4, 2-9, 4-10
inspecting 3-2, 4-1, 5-2
shipping to Neptune 3-2, 5-2, 9-28
use with RouteMAPS 2-1
using 2-1
handstraps
described 2-6
on handheld (illus.) 9-11 to 9-13
replacing 9-11 to 9-14
highlighting
See also selecting
defined G-3
host computers
connecting equipment to 3-5, 4-4
defined G-3
exchanging information with 7-1
host computers, exchanging information with 8-29,
8-40
tR
firmware
update 5-17
web update 5-16
firmware updates, R900 BCE 5-1
firmware, update 5-15
format
add gas 8-44, 8-47
create 8-36
custom 8-29
delete gas 8-50
delete ProRead 8-35
edit gas 8-44
edit ProRead 8-32
gas 8-46
manage 8-29
name 8-37
save ProRead 8-40
select gas 8-42
select ProRead 8-35
standard 8-34
forward keys
illustrated 3-15, 4-12, 4-18
found meters
found meters, see also adding meters to routes
function keys
defined G-2
described 3-13
hot keys
defined G-3
described 3-14, 4-13
I/O key 3-19, 4-19
index part number A-1
information exchange 7-1
information key 3-17, 4-17
information keys
defined G-3
described 3-16, 3-18, 4-16, 4-18
INS/ESC key 3-19, 4-19
inspecting, equipment 3-2, 4-1, 5-2
installing
battery 9-10
battery, CE5320B 9-10
handstrap 9-11, 9-14
LEMO cable 3-8
power supply 3-5, 4-4
router 3-5, 4-5
interconnect wires, networking 8-29
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Index
Pi
lo
L key 3-18, 4-17
LANs, see local area networks
LED operating modes 5-8
LEDs
bluetooth 5-9
error codes 5-9
explained 5-8
mode 5-8
power 5-8
RF mode 5-9
LEMO connectors, as part of system 3-2
letter keys
defined G-3
described 3-15
illustrated 3-12, 4-11
letter, entering 3-15
list key 3-17, 4-17
local area networks, defined G-3
location codes, defined G-3
login screen 8-30, 8-41
Logout key 3-18, 4-17
long-term storage, preparing the unit for 9-2
low-power state 2-7, 2-12
el
ea
tR
key
browse 3-17, 4-17
edit 3-16, 4-16
entry, manual 3-17, 4-17
for screen information 3-17, 4-17
for Search 3-17, 4-16
GoTo 3-17, 4-16
information 3-17, 4-17
list 3-17, 4-17
Logout 3-18, 4-17
manual entry 3-17, 4-17
Meter 3-18, 4-17
Properties 3-18, 4-17
RF test 3-18, 4-17
Skip 3-18, 4-17
Tag 3-18, 4-17
Tag search 3-18, 4-17
to exit 3-18, 4-17
W, to logout 3-18, 4-17
key AMR mode 3-16, 4-16
key, Find 3-17, 4-16
keyboard backlights, described 2-10
keyboard click, selecting 3-24, 4-28
keyboards
backlight 2-4, 2-10
backlights described 2-4
CE5320B (illus) 2-4
character keys 3-15 to 3-16
character keys (illus.) 3-12, 4-10
color coding 3-13, 3-15, 4-11
described 2-4, 2-9
direction keys 3-14 to 3-15, 4-12, 4-18\
direction keys (illus.) 3-12, 4-10
enabling Keyboard Click 3-24, 4-27
function keys 3-13
function keys (illus.) 3-12, 4-10
illustrated 3-12, 4-11
information keys 3-16 to 3-18, 4-15, 4-18
information keys (illus.) 3-12
letter keys 3-15 to 3-16
letter keys (illus.) 3-12, 4-11
number keys 3-14, 4-12
number keys (illus.) 3-12
quick keys 3-19, 4-19
quick keys (illus.) 3-12, 4-10, 4-11
selecting Keyboard Click 3-24, 4-27 to 4-28
Trimble Nomad (illus) 2-9
keyin direction, selecting 3-23, 4-27
keys, color-coding 3-15, 3-19, 4-19
se
J key 3-17, 4-17
M key 3-18, 4-17
Main Menu screen, illustrated 6-8, 6-16, 6-26, 6-37
main screens
described 2-14 to 2-15
illustrated 2-14 to 2-15
maintenance
frequency of 9-1
proper storage 9-2 to 9-3
recommended 9-1
manage formats 8-29
N_SIGHT R900 User’s Manual for the Neptune Handheld System
I-5
Index
se
access RF test mode 5-13
bluetooth 5-9
error codes LEDs 5-9
LED 5-8
LED operating 5-8
normal filtered reading 5-5
RF 5-9
RF performance 5-11
RF test 5-13
SD card error, LED 5-9
unattended 5-5
unfiltered reading 5-5
mouse, button 8-20
moving
in a data-entry space 3-15, 4-12, 4-18
through screens 2-17
within a route 6-33, 6-35
MS-DOS
See also Windows 95, Windows NT, operating
systems
defined G-4
MTR INFO key 3-18, 4-17
multiple-route assignments, defined G-4
multiplier, gas 8-45
multitasking, defined G-4
Pi
lo
tR
el
ea
manual entry key 3-17, 4-17
manual OFF, described 2-7, 2-12
menu screens 2-15
defined G-3
described 2-14, 2-15
example (illus.) 2-14
example of (illus.) 2-14
menus
Main 6-37
Utility 3-25, 4-28
message screens
defined G-3
described 2-17
example (illus.) 2-15
messages
e-mail 1-6
See route messages, survey messages, error
messages, broadcast messages
Meter 2-1
meter information, displaying screens with 2-18
Meter key 3-18, 4-17
meter numbers, defined G-4
meter reader tasks
defined 1-7
described 2-3
meter readers
described 1-7
responsibilities 1-8
meter reading cycle, illustrated 5-2
meter readings
See also readings
collecting manually 6-3
meters
changing information about 2-21, 6-30 to 6-32
displaying information 3-19, 4-19
MHz, defined G-4
microprocessors
See also central processing units
defined G-4
MIU IDs, defined G-4
mode LED 5-8
mode, suspend 2-7, 2-12
modems, defined G-4
moderate performance 5-12, 5-14
modes
I-6
N_SIGHT R900 database server, defined G-4
N_SIGHT R900 status screen 5-7, 5-11
navigating screens 2-17
Neptune key, illustrated 5-7
networking 8-28
new meters
adding 6-28 to 6-29
NEW MTR key 3-18, 4-17
Nomad
charger 4-3, 4-4, 4-5, 4-6
charger illus. 4-3
display 2-9
Nomad, basic features 2-9, 2-12
normal filtered reading mode 5-5
number keys
defined G-4
described 3-14, 4-12
illustrated 3-12, 4-10
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Index
Pi
lo
se
pressure compensation factors, table of A-1
Pressure Configuration Factor 8-45
problems
See also troubleshooting
solving 10-1 to 10-6
program
gas 8-18
gas register 8-40
network secondary register 8-28
R900G 8-18
program result, gas 8-20
prompts
defined G-5
Properties key 3-18, 4-17
ProRead
preferences 8-30
query 8-14
read 8-15
select format 8-32
el
ea
P key 3-18, 4-17
packing the handheld 9-28
pair, R900 BCE 5-10
parts
list of replaceable 9-26
ordering 9-26
recommended spare 9-26
password
Gas login (Field Programmer) 8-41
ProRead login 8-30, 8-41
PCF 8-45
PCs
See also personal computers
defined G-5
performance RF 5-14
performance, best 5-12, 5-14
pop-ups, defined G-5
power supply, connecting 3-5, 4-4
preferences
Gas 8-41
preferences, ProRead 8-30
pressure
atmospheric A-1
base A-1
gauge A-1
tR
office codes, defined G-4
operating mode, LED 5-8
operating systems
See also Windows 95, Windows NT, MS-DOS
defined G-5
operating temperatures 2-7, 2-12
operator tasks
defined 1-7
described 2-3
operators
described 1-7
responsibilities 1-9
options, Customer Support 1-6
order
defined G-5
ordering parts 9-26
overview, R900 BCR 5-1
Q key 3-18, 4-17
query ProRead 8-14
query, results 8-15
quick keys
defined G-5
described 3-19, 4-19
illustrated 3-12, 4-11
R key 3-18, 4-17
R900 BCR
change modes 5-4
components 5-3
firmware updates 5-1
overview 5-1
pair bluetooth 5-10
read route 5-11
SD card 5-14
status screen 5-11
update firmware 5-15
USB transfer cable 5-17
R900 BCR firmware 5-15
R900 BCR modes
explanation 5-5
N_SIGHT R900 User’s Manual for the Neptune Handheld System
I-7
Index
el
ea
se
replacing
battery 9-9\ to 9-10
handstrap 9-11, 9-13 to 9-14
reset handheld 10-7, 10-9
resistance
electromagnetic 2-7, 2-13
shock 2-8, 2-13
water 2-7, 2-12
returning CE5320B 9-28
RF mode 5-9
RF performance 5-14
RF test
mode 5-13
RF Test key 3-18, 4-17
RF test mode
access 5-13
rotation, clockwise or counter-clockwise 8-46
route directions, changing 3-24, 4-27
route information, displaying screens with 2-18
route messages
See also broadcast messages, survey messages
defined G-6
router, connecting 3-5, 3-8, 4-5
routes, problems with downloading 10-6
Pi
lo
tR
LED operating 5-8
operation 5-4, 5-7
summary 5-4, 5-7
R900 Belt Clip Receiver
overview 5-1
USB transfer cable 5-17
R900G, program 8-18
ratio A-1
read
gas 8-26
ProRead 8-15
reading a route 5-11
reading mode
access 5-13
reading-entry screens
defined G-5
displaying 2-17, 2-19
example (illus.) 2-18
sample used in manual 6-1
readings
bypassing 6-3
clearing 6-22, 6-24, 6-26, 6-39, 6-41
collecting 6-3
entering into the handheld 6-3 to 6-4
entering skip code 6-5
leaving blank 6-11
problems with uploading 10-6
validating 6-20
readings, store 5-1
readings, validate 6-20
read-type codes, defined G-5
reboot
handheld 10-9
logged off 10-11
logged on 10-9
receiving information from host 7-4 to 7-5
recharging the battery 9-5
refresh, R900G 8-24
region codes, defined G-5
register, program secondary 8-28
registers, network 8-28
removing
battery 9-9 to 9-10
handstrap 9-11 to 9-12
I-8
save
gas format 8-46
ProRead format 8-40
screens
Beeper Menu (illus.) A-2
data-entry 2-16
data-entry example (illus.) 2-14
defined G-6
entering information in 2-17
GoTo 6-37
Main Menu (illus.) 6-37
menu 2-15
menu example (illus.) 2-14
message 2-17
message example (illus.) 2-15
navigating through 2-17
overview 2-14, 2-17
reading-entry example 2-18
types 2-14, 2-17
N_SIGHT R900 User’s Manual for the Neptune Handheld System
Index
4-18
Pi
lo
tR
el
ea
Keyboard Click 3-24, 4-27 to 4-28
keyin direction 3-23, 4-27, 6-14
menu items 3-14, 4-12
search feature 6-17
selection list
gas 8-19
gas formats 8-44
ProRead 8-10
tokens 8-39
sending and receiving information
described 7-1
with device 7-4
sequence numbers, defined G-6
setting up, hardware for communication 3-5, 3-8, 4-4
shipping
damage 3-2, 4-1, 5-2
instructions for 9-28
packing required for 9-28
packing requirements 3-2, 5-2
to Neptune 9-28
shock resistance 2-8, 2-13
short-term storage
preparing for 9-2
signing off
defined G-6
how to 3-30, 4-36
signing on 3-26, 4-31
defined G-6
skip code 6-24
skip codes
clearing 6-22, 6-24, 6-26, 6-39, 6-41
defined G-6
entering 6-5
Skip key 3-18, 4-17
skip routes
See also blank routes
defined G-6
sleep mode, gas 8-24
software
finding version number 1-3
resetting 10-7, 10-9
starting from MS-DOS 10-6
SP key 3-19, 4-19
standard format 8-34
status screen, N_SIGHT R900 5-7, 5-11
store R900 readings 5-1
storing
long-term 9-2
short-term 9-2
support, customer 1-5
survey messages
See also broadcast messages, route messages
defined G-7
suspend mode 2-7, 2-12
symbols, used in manual 1-1
synchronize screen 5-7
synchronize, defined G-7
system configuration
communication cradle 3-2
determining 3-1
equipment needed 3-3, 4-3
LEMO connector 3-2
system settings
adjustment options 3-20, 4-22
overview 3-20, 4-22
se
screens (continued)
Utility Menu (illus.) 3-25, 4-28
with meter or route information 2-18
SD card 5-6, 5-14
SD card error 5-9
search, Y key for Tag search 3-18, 4-17
select format
gas 8-42
ProRead 8-32, 8-35
select preferences
gas 8-40, 8-41
ProRead 8-30
selecting
See also highlighting
defined G-6
items from menu screens 3-14, 3-15, 3-16, 4-13,
tag
defined G-7
indicators, defined G-7
Tag key 3-18, 4-17
Tag search key 3-18, 4-17
temperatures, operating 2-7, 2-12
test hand, gas 8-45
N_SIGHT R900 User’s Manual for the Neptune Handheld System
I-9
Index
up key, illustrated 3-15, 4-18
uploading
defined G-7
overview 2-1
problems with 10-6
USB mass storage 5-6
USB transfer cable 5-17
user IDs, defined G-7
Utility Menu screen, illustrated 3-25, 4-28
el
ea
se
validate readings 6-20
validating readings 6-20
version number 3-17, 4-17
volume control
CE5320 A-1
Nomad A-5
tR
tokens, custom format 8-39
TOTAL key 3-17, 4-16
transporting the PC9800 9-4
Trimble Nomad
keyboard 2-9
trouble codes, defined G-7
troubleshooting
Audit Failed error message 6-20
bookmark feature 10-5
display 10-2, 10-3, 10-4, 10-5
non-responsive unit 10-2, 10-4
unit won't turn off 10-3, 10-5
upload/download unsuccessful 10-6
turning off
automatic return 2-7, 2-12
automatically 3-30, 4-31, 4-36
handheld 4-31
keyboard backlight 3-20, 4-20
manually 3-19, 4-19
problems with 10-3, 10-5
turning on
automatic return 2-7, 2-12
handheld 3-19, 4-19, 4-30
keyboard backlight 3-20, 4-20
yellow keys, using 4-11
Pi
lo
unattended mode 5-5
unfiltered reading mode 5-5
unloading information, see sending and receiving
information
unpacking, equipment 3-2, 4-1, 5-2
W key, to exit 3-18, 4-17
wake up, gas 8-24
warranty, voiding 2-5, 2-10
water resistance 2-7, 2-12
Windows
CE.Net screen, illustrated A-2
Windows, defined G-7
workstations, defined G-7
I-10
N_SIGHT R900 User’s Manual for the Neptune Handheld System
se
el
ea
tR
lo
Pi
se
el
ea
tR
lo
Pi
Neptune Technology Group Inc.
1600 Alabama Highway 229
Tallassee, AL 36078
USA
Tel: (800) 633-8754
Fax: (334) 283-7293
UM Handheld System 11.13
Neptune Technology Group (Canada) Ltd.
7275 West Credit Avenue
Mississauga, Ontario
L5N 5M9
Canada
Tel: (905) 858-4211
Fax: (905) 858-0428
Neptune Technology Group Inc.
Ejército Nacional No. 418
Piso 12, Desp. 1201-1202
Col. Chapultepec Morales
Delegación Miguel Hidalgo
11570 México, Distrito Federal
Tel: (525) 55203 5294 / (525) 55203 5708TAKE CONTROL
Fax: (525) 55203 6503
neptunetg.com
Part No. 11769-016 © Copyright 2005-2013, Neptune Technology Group Inc. Neptune is a registered trademark of Neptune Technology Group Inc

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Author                          : courtney.mcgann
Create Date                     : 2013:12:02 10:00:31-05:00
Modify Date                     : 2013:12:02 10:21:31-05:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Producer                        : ScanSoft PDF Create! 7
Creator Tool                    : Microsoft Word - 13-0249- Exhibit Cover.doc
Metadata Date                   : 2013:12:02 10:21:31-05:00
Format                          : application/pdf
Title                           : Microsoft Word - 13-0249- Exhibit Cover.doc
Creator                         : courtney.mcgann
Document ID                     : uuid:b432e0e1-f966-4a79-a1e3-58ec5b52de10
Instance ID                     : uuid:71829dfd-5032-4c3e-8194-ff6e55eb0d3a
Page Count                      : 311

EXIF Metadata provided by EXIF.tools