Netgear orporated 05400024 Integrated ADSL Modem + Wireless Router with Voice User Manual DG834GV SM

Netgear Incorporated Integrated ADSL Modem + Wireless Router with Voice DG834GV SM

Usermanual

February 2006NETGEAR, Inc.4500 Great America Parkway Santa Clara, CA 95054 USASetup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with Voice
iiv1.0, February 2006© 2006 by NETGEAR, Inc. All rights reserved.TrademarksNETGEAR is a trademark of Netgear, Inc. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. Other brand and product names are registered trademarks or trademarks of their respective holders.Statement of ConditionsIn the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice.NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.
Regulatory Approvals FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communica-tions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Channel The Wireless Channel sets the radio frequency used for communication. •Access Points use a fixed Channel. You can select the Channel used. This allows you to choose a Channel which provides the least interference and best performance. In the USA and Canada, 11 channel are available. If using multiple Access Points, it is better if adjacent Access Points use different Channels to reduce interference. • In "Infrastructure" mode, Wireless Stations normally scan all Channels, looking for an Access Point. If more than one Access Point can be used, the one with the strongest signal is used. (This can only happen within an ESS.) • If using "Ad-hoc" mode (no Access Point), all Wireless stations should be set to use the same Channel. However, most Wireless stations will still scan all Channels to see if there is an existing "Ad-hoc" group they can join.Note:This equipment marketed in USA is restricted by firmware to only operate on 2.4G channel 1-11.
1v1.0, February 2006ContentsSetup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with VoiceChapter 1 Connecting the Router to the InternetWhat’s in the Box? ..........................................................................................................1-1The Router’s Front Panel .........................................................................................1-2The Router’s Rear Panel .........................................................................................1-3What You Need Before You Begin ..................................................................................1-4Internet Configuration Requirements .......................................................................1-4Two Setup Methods: 1) Smart Wizard Setup 2) Manual Setup ......................................1-4Smart Wizard Setup .......................................................................................................1-5Manual Setup .................................................................................................................1-6Understanding ADSL Microfilters .............................................................................1-6Computers Set to DHCP ..........................................................................................1-7Manually Setting Up Your ADSL Modem Wireless Router .............................................1-7How to Manually Set Up and Test Basic Wireless Connectivity ...................................1-13Implement Appropriate Wireless Security ....................................................................1-14Chapter 2 TroubleshootingBasic Functioning ...........................................................................................................2-1Power LED Not On ...................................................................................................2-2Test LED Never Turns On or Test LED Stays On .....................................................2-2LAN or ADSL Internet Port LEDs Not On .................................................................2-3Troubleshooting the Web Configuration Interface ..........................................................2-3Troubleshooting the ISP Connection ..............................................................................2-4ADSL link .................................................................................................................2-4Obtaining an Internet IP Address .............................................................................2-5Troubleshooting PPPoE or PPPoA ..........................................................................2-6
2v1.0, February 2006Troubleshooting Internet Browsing ..........................................................................2-7Troubleshooting a TCP/IP Network Using the Ping Utility ..............................................2-7Testing the LAN Path to Your Router .......................................................................2-7Testing the Path from Your Computer to a Remote Device .....................................2-8Restoring the Default Configuration and Password ........................................................2-9Using the Reset Button ............................................................................................2-9Appendix A Technical SpecificationsAppendix B Related Documents
Connecting the Router to the Internet 1-1v1.0, February 2006Chapter 1 Connecting the Router to the InternetThis chapter describes how to set up the router on your Local Area Network (LAN) and connect to the Internet. It describes how to set up your ADSL modem wireless router for Internet access and configure basic wireless connectivity.What’s in the Box?The product package should contain the following items:• ADSL Modem Wireless Router• AC power adapter (varies by region)• Category 5 (Cat 5) Ethernet cable• Telephone cable with RJ-11 connector• Microfilters (quantity and type vary by region)•Resource CD, including:— The Smart Wizard Installation Assistant— This manual• Warranty and Support Information cardsIf any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the carton, including the original packing materials, in case you need to return the product for repair.
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with Voice1-2 Connecting the Router to the Internetv1.0, February 2006The ADSL Modem Wireless Router’s Front PanelThe ADSL modem wireless router front panel shown below contains status LEDs. You can use the LEDs to verify various conditions. Table 1-1 describes each LED.Figure 1-1Table 1-1. LED Descriptions Label Activity Description1. PowerOn (Green)On (Red)OffPower is supplied to the router.Power-on Self-test failure or device malfunction.Power is not supplied to the router.2. TestOn (Amber)Blink (Amber)OffSystem is not ready or failed to start up.The system is initializing.The system is ready and running.3. ADSLOn (Green)Blink (Green)OffADSL is synchronized.DSL is attempting to synchronize.No link is detected on this port or modem is not powered on.4. InternetOn (Green)Flicker (Green)RedOffInternet port is connected, has an IP address, DSL is up, no traffic detected.Traffic is passing through the connected internet port in either direction.Device attempted to connect, but failed.Modem powered off or in bridged mode, or ADSL connection not present.12 345 6 7
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with VoiceConnecting the Router to the Internet 1-3v1.0, February 2006The ADSL Modem Wireless Router’s Rear PanelThe rear panel of the ADSL modem wireless router contains port connections.Viewed from left to right, the rear panel contains the following elements:1. RJ-11 ADSL port for connecting the router to a telephone wall jack via the ADSL port of a phone splitter2. RJ-11 PSTN port for connecting the router to the telephone wall jack via the phone port of a phone splitter5. WirelessOn (Green)Blink (Green)OffWireless port is linked.Data is being transmitted or received.No wireless link. 6. Phone1 Phone2On (Green)Fast blinkSlow blinkOffRegistered to SIP server.Talking.Off hook.Phone not ready.7. FXO/PSTN fallbackOn (Green)BlinkOffPSTN line detected.Talking.No PSTN line detected.Figure 1-2Table 1-1. LED Descriptions (continued)1234567
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with Voice1-4 Connecting the Router to the Internetv1.0, February 20063. Two phone ports for connecting to telephones4. Four Local Ethernet RJ-45 LAN ports for connecting the router to the local computers5. Factory Default Reset push button6. AC power adapter outlet7. Wireless antennaEach LAN port has two LEDs, one green and one amber. They indicate the port status as follows:• On (Green) LAN port is linked to a 100Mbps device• Blink (Green) Data is being transmitted or received at 100 Mbps• On (Amber) LAN port is linked to a 10Mbps device• Blink (Amber) Data is being transmitted or received at 10 Mbps• Off No link is detected on this port
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with VoiceConnecting the Router to the Internet 1-5v1.0, February 2006What You Need Before You BeginYou need to prepare the following before you can set up your router:• Active Internet service provided by an ADSL account.• The Internet Service Provider (ISP) configuration information for your ADSL account.• ASDL microfilters as explained below.• Your computers set to DHCP.Internet Configuration RequirementsDepending on how your ISP set up your Internet account, you need one or more of these configuration parameters to connect your router to the Internet: • Virtual Path Identifier (VPI)/Virtual Channel Indentifier (VCI) parameters• Multiplexing Method• Host and Domain Names• ISP Login Name and Password• ISP Domain Name Server (DNS) Addresses• Fixed or Static IP AddressYour ISP should have provided you with all the information needed to connect to the Internet. If you cannot locate this information, you can ask your ISP to provide it. Two Setup Methods: 1) Smart Wizard Setup 2) Manual SetupYou have two methods available for setting up your ADSL modem wireless router:•Smart Wizard Setup: Use the Smart Wizard on the CD to assist you with setting up your ADSL modem wireless router.— This option is the easiest. The Smart Wizard on the CD guides you through the setup process, automating many of the steps, and verifying that necessary conditions exist and that steps you perform have been successfully completed.— This option requires a PC running Microsoft Windows 98SE or higher.
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with Voice1-6 Connecting the Router to the Internetv1.0, February 2006•Manual Setup: Manually set up your ADSL modem wireless router.— This option is best if you are replacing an existing ADSL modem wireless router or are technically knowledgeable.— Use this option if you are using a computer that does not run Microsoft Windows.— The manual setup procedures are documented in this manual. Use the setup option that best suites you.Smart Wizard SetupThe Smart Wizard setup process should take about 20 minutes to complete.1. Locate the ADSL settings information your Internet service provider gave you.2. Insert the NETGEAR CD into a Windows PC.The CD will automatically start and detect the language you are using on your PC. 3. Accept the language option or change to a different language.4. Click Next to proceed.5. Click Setup to start the Smart Wizard installation assistant. Follow the instructions on the screen.Note: If the CD does not automatically start, browse the CD and double-click on Autorun.
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with VoiceConnecting the Router to the Internet 1-7v1.0, February 2006Manual SetupUse the topics and procedures below to manually set up your ADSL modem wireless router.Understanding ADSL MicrofiltersADSL technology uses the same wires as your telephone service. However, ADSL adds signals to the telephone lines which create noise in the telephone service. You must use ADSL microfilters to filter out these signals before they reach your telephone.ADSL Microfilter with Built-In SplitterUse the ADSL microfilter with built-in splitter to provide connectivity to the ADSL modem wireless router and telephone equipment connected to that router.ADSL MicrofilterEach device directly connected to the phone line, such as a fax machine, answering machine, or caller ID display will require an ADSL microfilter.Note: If you purchased the ADSL modem wireless router in a country where a microfilter is not included, you must acquire one.Figure 1-3Figure 1-4PhoneADSLLinePhone
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with Voice1-8 Connecting the Router to the Internetv1.0, February 2006Computers Set to DHCPFor the initial connection to your router, your computer has to be set to automatically get its TCP/IP configuration from the router via DHCP. This is usually the case. The NETGEAR Smart Wizard CD automatically takes care of this requirement. For manual setup, refer to the documentation that came with your computer.Manually Setting Up Your ADSL Modem Wireless RouterThere are four steps to setting up your ADSL modem wireless router:6. Connect the router to the ADSL line via the ADSL microfilter with built-in splitter.1. Install ADSL filters on other phone lines that use the same telephone number.2. Log in to the router.3. Connect to the Internet.Follow the steps below to connect your router to your network. Before you begin, locate the ADSL configuration information from your Internet Service Provider (ISP). 1. Connect the ADSL filter with built-in splitter, as follows:a. Connect the Line port of the ADSL filter/splitter to the telephone wall socket.b. Using telephone cable with RJ11 jacks, connect the ADSL port of the filter/splitter to the ADSL port on the left rear of the ADSL modem wireless routerNote: If you purchased the DG834GVSP in a country where an ADSL filter is not included, you must acquire one.
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with VoiceConnecting the Router to the Internet 1-9v1.0, February 2006c. Connect the Phone port of the filter/splitter to the green PSTN connector on the ADSL modem wireless router.:d. You need to install a separate ADSL filter (see Figure 1-4 on page 1-6) for every telephone connected to other wall sockets that use the same telephone number as your ADSL modem wireless router.Figure 1-5
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with Voice1-10 Connecting the Router to the Internetv1.0, February 2006e. If you have voice service or plan to order it, connect a telephone to Phone Port 1 on the ADSL modem wireless router.Figure 1-6Note: In the event of a power outage or loss of internet connectivity, the router will automatically connect to the standard phone port until VoIP service is restored. This feature is not available on Phone Port 2.Phone Port 1
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with VoiceConnecting the Router to the Internet 1-11v1.0, February 2006f. Connect the Ethernet cable from an ADSL modem wireless router LAN port to the Ethernet adapter in your computer.g. If you have more than one computer, repeat step f using a different LAN port on the ADSL modem wireless router.h. Connect the power adapter to the router and plug it in to a power outlet. i. Verify the following: The power light is lit after turning on the router. The test light comes on briefly, then goes off. The wireless light is lit after turning on the router.Figure 1-7Figure 1-8
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with Voice1-12 Connecting the Router to the Internetv1.0, February 2006 The ADSL internet light is green, indicating you are connected to the ADSL network.j. Now, turn on your computer. If software usually logs you in to your Internet connection, do not run that software. Cancel it if it starts automatically. Verify the following: The appropriate LAN port LEDs are lit for any connected computers.2. Log in to the ADSL modem wireless router as described below.a. Type http://192.168.0.1 in the address field of a browser such as Internet Explorer or Netscape® Navigator.This login window opens:Enter admin for the user name and password for the password, both in lower case letters. Note: Your computer needs to be configured for DHCP. For instructions on configuring for DHCP, please see the documentation that came with your computer or the online document, “Preparing a Computer for Network Access”.Figure 1-9Figure 1-10
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with VoiceConnecting the Router to the Internet 1-13v1.0, February 2006b. After logging in, you will see the menu below. 3. Connect to the Internet:You are now ready to configure your ADSL modem wireless router to connect to the Internet. There are two ways you can configure your ADSL modem wireless router to connect to the Internet:a. Let the ADSL modem wireless router Setup Wizard auto-detect the type of Internet connection you have and configure it. b. Manually choose which type of Internet connection you have and configure it. In either case, use to the configuration parameters your ISP provided to assure that the configuration settings for your Internet connection are correct.4. Test your Internet connection.From the bottom of the Setup menu, click Test. If the NETGEAR Web site does not appear within one minute, refer to Chapter 2, “Troubleshooting”.Your ADSL modem wireless router is now configured to provide Internet access for your network. Your ADSL modem wireless router automatically connects to the Internet when one of your computers requires access. It is not necessary to run a dialer or login application such as Dial-Up Networking or Enternet to connect, log in, or disconnect. These functions are performed automatically by the ADSL modem wireless router as needed.Figure 1-11
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with Voice1-14 Connecting the Router to the Internetv1.0, February 2006To access the Internet from any computer connected to your ADSL modem wireless router, launch a browser such as Microsoft Internet Explorer or Netscape Navigator. You should see the ADSL modem wireless router’s Internet LED blink, indicating communication to the ISP. The browser should begin to display a Web page.How to Manually Set Up and Test Basic Wireless ConnectivityFollow the instructions below to set up and test basic wireless connectivity. Once you have established basic wireless connectivity, you can enable security settings appropriate to your needs.1. Log in to the ADSL modem wireless router at its default LAN address of http://192.168.0.1 with its default user name of admin and default password of password, or using whatever LAN address and password you have set up.2. Click the Wireless Settings link in the main menu of the ADSL modem wireless router.Figure 1-12
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with VoiceConnecting the Router to the Internet 1-15v1.0, February 20063. Note that the default SSID is NETGEAR.4. Set the Region. Select the region in which the wireless interface will operate. 5. Click Apply to save your changes.6. Configure and test your computers for wireless connectivity:Program the wireless adapter of your computers to have the same wireless network name (SSID) as the ADSL modem wireless router. Check that they have a wireless link and are able to obtain an IP address by DHCP from the router.Implement Appropriate Wireless SecurityUnlike wired network data, your wireless data transmissions can extend beyond your walls and can be received by anyone with a compatible adapter. For this reason, use the security features of your wireless equipment. The ADSL modem wireless router provides highly effective security features which are covered in detail in the full reference manual that is available from a link on the CD as well as a link in the main menu of your router. Follow the instructions in the full manual and in the router help screens to deploy the security features appropriate to your needs.Note: The SSID of any wireless adapters must match the SSID you configure in the ADSL modem wireless router. If they do not match, you will not get a wireless connection.Note: If you are configuring the router from a wireless computer and you change the router’s SSID, channel, or security settings, you will lose your wireless connection when you click Apply. You must then change the wireless settings of your computer to match the router’s new settings.Warning: Indoors, computers can connect over 802.11g wireless networks at a maximum range of up to 300 feet. Such distances can allow for others outside of your immediate area to access your network.
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with Voice1-16 Connecting the Router to the Internetv1.0, February 2006
Troubleshooting 2-1v1.0, February 2006Chapter 2 TroubleshootingThis chapter gives information about troubleshooting your ADSL modem wireless router. After each problem description, instructions are provided to help you diagnose and solve the problem. For the common problems listed, go to the section indicated.• Is the router on?Go to “Basic Functioning” on page 2-1.• Have I connected the router correctly?Go to “Basic Functioning” on page 2-1.• I cannot access the router’s configuration with my browser.Go to “Troubleshooting the Web Configuration Interface” on page 2-3.• I have configured the router but I can’t access the Internet.Go to “Troubleshooting the ISP Connection” on page 2-4.• I cannot remember the router’s configuration password.Go to “Using the Reset Button” on page 2-9.• I want to clear the configuration and start over again.Go to “Restoring the Default Configuration and Password” on page 2-9.Basic FunctioningAfter you turn on power to the router, the following sequence of events should occur:1. When power is first applied, verify that the Power LED is on (see “The Router’s Front Panel” on page 1-2 for an illustration and explanation of the LEDs).2. Verify that the Test LED lights within a few seconds, indicating that the self-test procedure is running.3. After approximately 10 seconds, verify that:a. The Test LED is not lit.
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with Voice2-2 Troubleshootingv1.0, February 2006b. The LAN port LEDs are lit for any local ports that are connected.c. The ADSL Internet port LED is lit.If a port’s LED is lit, a link has been established to the connected device. If a LAN port is connected to a 100 Mbps device, verify that the port’s LED is green. If the port is 10 Mbps, the LED will be amber.If any of these conditions does not occur, refer to the appropriate following section.Power LED Not OnIf the Power and other LEDs are off when your router is turned on:• Make sure that the power cord is properly connected to your router and that the power supply adapter is properly connected to a functioning power outlet. • Check that you are using the power adapter supplied by NETGEAR for this product.If the error persists, you have a hardware problem and should contact technical support.Test LED Never Turns On or Test LED Stays OnWhen the router is turned on, the Test LED turns on for about 10 seconds and then turns off. If the Test LED does not turn on, or if it stays on, there is a fault within the router.If you experience problems with the Test LED:• Cycle the power to see if the router recovers and the LED blinks for the correct amount of time.If all LEDs including the Test LED are still on one minute after power up:• Cycle the power to see if the router recovers.• Clear the router’s configuration to factory defaults. This will set the router’s IP address to 192.168.0.1. This procedure is explained in “Using the Reset Button” on page 2-9.If the error persists, you might have a hardware problem and should contact technical support.
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with VoiceTroubleshooting 2-3v1.0, February 2006LAN or ADSL Internet Port LEDs Not OnIf either the LAN LEDs or ADSL Internet LED do not light when the Ethernet connection is made, check the following:• Make sure that the Ethernet cable connections are secure at the router and at the hub or workstation.• Make sure that power is turned on to the connected hub or workstation.• Be sure you are using the correct cable: when connecting the ADSL port, use the cable that was supplied with the ADSL modem wireless router.Troubleshooting the Web Configuration InterfaceIf you are unable to access the router’s Web Configuration interface from a computer on your local network, check the following:• If you are using an Ethernet-connected computer, check the Ethernet connection between the computer and the router as described in the previous section.• Make sure your computer’s IP address is on the same subnet as the router. If you are using the recommended addressing scheme, your computer’s address should be in the range of 192.168.0.2 to 192.168.0.254. Refer to “Preparing a Computer for Network Access” to find your computer’s IP address. Note: If your computer’s IP address is shown as 169.254.x.x: Recent versions of Windows and MacOS will generate and assign an IP address if the computer cannot reach a DHCP server. These auto-generated addresses are in the range of 169.254.x.x. If your IP address is in this range, check the connection from the computer to the router and reboot your computer.• If your router’s IP address was changed and you do not know the current IP address, clear the router’s configuration to factory defaults. This will set the router’s IP address to 192.168.0.1. This procedure is explained in “Using the Reset Button” on page 2-9.• Make sure your browser has Java, JavaScript, or ActiveX enabled. If you are using Internet Explorer, click Refresh to be sure the Java applet is loaded.• Try quitting the browser and launching it again.• Make sure you are using the correct login information. The factory default login name is admin and the password is password. Make sure that CAPS LOCK is off when entering this information.
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with Voice2-4 Troubleshootingv1.0, February 2006If the router does not save changes you have made in the Web Configuration Interface, check the following:• When entering configuration settings, be sure to click the Apply button before moving to another menu or tab, or your changes are lost. • Click the Refresh or Reload button in the Web browser. The changes may have occurred, but the Web browser may be caching the old configuration.Troubleshooting the ISP ConnectionIf your router is unable to access the Internet, you should check the ADSL connection, then the Internet TCP/IP connection. ADSL linkIf your router is unable to access the Internet, you should first determine whether you have an ADSL link with the service provider. The state of this connection is indicated with the Internet LED.ADSL Internet LED Green or Blinking GreenIf your ADSL Internet LED is green or blinking green, then you have a good ADSL connection. You can be confident that the service provider has connected your line correctly and that your wiring is correct.ADSL Internet LED Blinking YellowIf your ADSL Internet LED is blinking yellow, then your ADSL modem wireless router is attempting to make an ADSL connection with the service provider. The LED should turn green within several minutes. If the Internet LED does not turn green, disconnect all telephones on the line. If this solves the problem, reconnect the telephones one at a time, being careful to use a microfilter on each telephone. If the microfilters are connected correctly, you should be able to connect all your telephones.If disconnecting telephones does not result in a green ADSL Internet LED, there may be a problem with your wiring. If the telephone company has tested the ADSL signal at your Network Interface Device (NID), then you may have poor quality wiring in your house.
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with VoiceTroubleshooting 2-5v1.0, February 2006ADSL Internet LED OffIf the ADSL Internet LED is off, disconnect all telephones on the line. If this solves the problem, reconnect the telephones one at a time, being careful to use a microfilter on each telephone. If the microfilters are connected correctly, you should be able to connect all your telephones.If disconnecting telephones does not result in a green ADSL Internet LED the problem may be one of the following:• Check that the telephone company has made the connection to your line and tested it.• Verify that you are connected to the correct telephone line. If you have more than one phone line, be sure that you are connected to the line with the ADSL service. It may be necessary to use a swapper if you ADSL signal is on pins 1 and 4 of the RJ-11 jack. The ADSL Modem Wireless Router uses pins 2 and 3.Obtaining an Internet IP AddressIf your ADSL modem wireless router is unable to access the internet, and your Internet LED is green or blinking green, you should determine whether the ADSL modem wireless router is able to obtain a Internet IP address from the ISP. Unless you have been assigned a static IP address, your ADSL modem wireless router must request an IP address from the ISP. You can determine whether the request was successful using the browser interface.To check the Internet IP address from the browser interface: 1. Launch your browser and select an external site such as http://www.netgear.com.2. Access the Main Menu of the ADSL modem wireless router’s configuration at http://192.168.0.1. 3. Under the Maintenance heading check that an IP address is shown for the Internet Port. If 0.0.0.0 is shown, your ADSL modem wireless router has not obtained an IP address from your ISP.If your router is unable to obtain an IP address from the ISP, the problem may be one of the following:• Your ISP may require a Multiplexing Method or Virtual Path Identifier/Virtual Channel Identifier parameter.Verify with your ISP the Multiplexing Method and parameter value, and update the router’s ADSL Settings accordingly.
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with Voice2-6 Troubleshootingv1.0, February 2006• Your ISP may require a login program.Ask your ISP whether they require PPP over Ethernet (PPPoE) or PPP over ATM (PPPOA) login.• If you have selected a login program, you may have incorrectly set the Service Name, User Name and Password. See “Troubleshooting PPPoE or PPPoA”, below.• Your ISP may check for your computer's host name. Assign the computer Host Name of your ISP account to the ADSL modem wireless router in the browser-based Setup Wizard.• Your ISP only allows one Ethernet MAC address to connect to Internet, and may check for your computer’s MAC address. In this case:Inform your ISP that you have bought a new network device, and ask them to use the router’s MAC address.ORConfigure your router to spoof your computer’s MAC address. This can be done in the Basic Settings menu. Refer to the online help in the ADSL modem wireless router main menu.Troubleshooting PPPoE or PPPoAThe PPPoA or PPPoA connection can be debugged as follows:1. Access the Main Menu of the router at http://192.168.0.1.2. Under the Maintenance heading, select the Router Status link.3. Click the Connection Status button.4. If all of the steps indicate “OK” then your PPPoE or PPPoA connection is up and working.5. If any of the steps indicates “Failed”, you can attempt to reconnect by clicking “Connect”. The ADSL modem wireless router will continue to attempt to connect indefinitely.If you cannot connect after several minutes, you may be using an incorrect Service Name, User Name or Password. There also may be a provisioning problem with your ISP.Note: Unless you connect manually, the ADSL modem wireless router will not authenticate using PPPoE or PPPoA until data is transmitted to the network.
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with VoiceTroubleshooting 2-7v1.0, February 2006Troubleshooting Internet BrowsingIf your ADSL modem wireless router can obtain an IP address but your computer is unable to load any Web pages from the Internet:• Your computer may not recognize any DNS server addresses. A DNS server is a host on the Internet that translates Internet names (such as www addresses) to numeric IP addresses. Typically your ISP will provide the addresses of one or two DNS servers for your use. If you entered a DNS address during the ADSL modem wireless router’s configuration, reboot your computer and verify the DNS address as described in “Preparing a Computer for Network Access”. Alternatively, you can configure your computer manually with DNS addresses, as explained in your operating system documentation.• Your computer may not have the wireless ADSL modem router configured as its TCP/IP default gateway.If your computer obtains its information from the ADSL modem wireless router by DHCP, reboot the computer and verify the ADSL modem wireless router address as described in “Preparing a Computer for Network Access”.Troubleshooting a TCP/IP Network Using the Ping UtilityMost TCP/IP terminal devices and routers contain a ping utility that sends an echo request packet to the designated device. The device then responds with an echo reply. Troubleshooting a TCP/IP network is made very easy by using the ping utility in your computer.Testing the LAN Path to Your RouterYou can ping the router from your computer to verify that the LAN path to your router is set up correctly.To ping the router from a PC running Windows 95 or later:1. From the Windows toolbar, click the Start button and select Run.2. In the field provided, type Ping followed by the IP address of the router, as in this example:ping 192.168.0.13. Click OK.You should see a message like this one:
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with Voice2-8 Troubleshootingv1.0, February 2006Pinging <IP address> with 32 bytes of dataIf the path is working, you see this message:Reply from < IP address >: bytes=32 time=NN ms TTL=xxxIf the path is not working, you see this message:Request timed outIf the path is not functioning correctly, you could have one of the following problems:• Wrong physical connections— Make sure the LAN port LED is on. If the LED is off, follow the instructions in “LAN or ADSL Internet Port LEDs Not On” on page 2-3.— Check that the corresponding Link LEDs are on for your network interface card and for the hub ports (if any) that are connected to your workstation and router.• Wrong network configuration— Verify that the Ethernet card driver software and TCP/IP software are both installed and configured on your PC or workstation.— Verify that the IP address for your router and your workstation are correct and that the addresses are on the same subnet.Testing the Path from Your Computer to a Remote DeviceAfter verifying that the LAN path works correctly, test the path from your PC to a remote device. From the Windows run menu, type:PING -n 10 <IP address>where <IP address> is the IP address of a remote device such as your ISP’s DNS server.If the path is functioning correctly, replies as in the previous section are displayed. If you do not receive replies:— Check that your PC has the IP address of your router listed as the default gateway. If the IP configuration of your PC is assigned by DHCP, this information will not be visible in your PC’s Network Control Panel. Verify that the IP address of the router is listed as the TCP/IP default gateway as described in “Preparing a Computer for Network Access”.— Check to see that the network address of your PC (the portion of the IP address specified by the netmask) is different from the network address of the remote device.— If your ISP assigned a host name to your PC, enter that host name as the Account Name in the Basic Settings menu.
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with VoiceTroubleshooting 2-9v1.0, February 2006Restoring the Default Configuration and PasswordThis section explains how to restore the factory default configuration settings, changing the router’s administration password to password and the IP address to 192.168.0.1. You can erase the current configuration and restore factory defaults in two ways:• Use the Erase function of the Web Configuration Manager.• Use the Reset button on the rear panel of the router. Use this method for cases when the administration password or IP address is not known.Using the Reset ButtonTo restore the factory default configuration settings without knowing the administration password or IP address, you must use the Default Reset button on the rear panel of the router.1. Press and hold the Reset button until the Test LED turns on (about 10 seconds).2. Release the Default Reset button and wait for the router to reboot.
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with Voice2-10 Troubleshootingv1.0, February 2006
Technical Specifications A-1v1.0, February 2006Appendix ATechnical SpecificationsThis appendix provides technical specifications for the ADSL modem wireless router.Network Protocol and Standards CompatibilityData and Routing Protocols: TCP/IP, RIP-1, RIP-2, DHCP, PPPoE or PPPoA, RFC 1483 Bridged or Routed Ethernet, and RFC 1577 Classical IP over ATMPower AdapterNorth America: 120V, 60 Hz, inputUK, Australia: 240V, 50 Hz, inputEurope: 230V, 50 Hz, inputJapan: 100V, 50/60 Hz, inputAll regions (output): 12 V AC @ 1.0A output, 30W maximumPhysical Dimensions: 10" x 6.7" x 1.3" 255 mm x 169 mm x 34 mmWeight: 1.4 lbs. 0.62 kgEnvironmental Operating temperature: 0° to 40° C (32º to 104º F)Operating humidity: 90% maximum relative humidity, noncondensingElectromagnetic EmissionsMeets requirements of: FCC Part 15 Class B; VCCI Class B; EN 55 022 (CISPR 22), Class BInterface SpecificationsLAN: 10BASE-T or 100BASE-Tx, RJ-45WAN: ADSL, ADSL2+, Dual RJ-11, pins 2 and 3 T1.413, G.DMT, G.Lite ITU Annex A or B
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with VoiceA-2 Technical Specificationsv1.0, February 2006
Related Documents B-1v1.0, February 2006Appendix B Related DocumentsThis appendix provides links to reference documents you can use to gain a more complete understanding of the technologies used in your NETGEAR product.Document LinkInternet Networking and TCP/IP Addressing http://documentation.netgear.com/reference/enu/tcpip/index.htmWireless Communications http://documentation.netgear.com/reference/enu/wireless/index.htmPreparing a Computer for Network Access http://documentation.netgear.com/reference/enu/wsdhcp/index.htmVirtual Private Networking (VPN) http://documentation.netgear.com/reference/enu/vpn/index.htmGlossary http://documentation.netgear.com/reference/enu/glossary/index.htm
Setup Manual for the DG834GVSP Integrated ADSL Modem and Wireless Router with VoiceB-2 Related Documentsv1.0, February 2006

Navigation menu