Netgear orporated 07400077 Prosafe 802.11n DualBand Wireless Access Point User Manual WNDAP330 IG

Download:
Mirror Download [FCC.gov]
Document ID	953374
Application ID	9EbAPChifmLHzGpRDjznfw==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	15.08kB (188550 bits)
Date Submitted	2008-06-10 00:00:00
Date Available	2008-06-10 00:00:00
Creation Date	2008-02-12 16:20:32
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2008-05-27 19:14:51
Document Title	WNDAP330_IG.fm
Document Creator	PScript5.dll Version 5.2.2
Document Author:	bduvall

b.
)NSTALLATION 'UIDE
WNDAP330 ProSafe 802.11n Dual Band Wireless Access Point
Attach the three antennas to your
wireless access point. The
antennas are interchangeable and
can be attached in any
configuration.
Start Here
c.
Connect an Ethernet cable from
the WNDAP330 to the PC (point
A in the illustration).
Follow these instructions to set up your wireless access point. Before proceeding with the
WNDAP330 installation, familiarize yourself with the contents of the Resource CD.
Please refer to the Reference Manual on your Resource CD for instructions on advanced
configuration options.
d.
Securely insert the other end of the
cable into the WNDAP330
Ethernet port (point B in the
illustration).
Estimated Completion Time: 30 minutes.
e.
Tip: Before mounting the WNDAP330 in a high location, first set up and test the
WNDAP330 to verify wireless network connectivity.
First, Verify the Package Contents
Unpack the box and verify the contents:
•
WNDAP330 ProSafe 802.11n Dual Band Wireless Access Point
•
Straight through Category 5 Ethernet cable
•
Power adapter and cord (12V, 1.5A)
•
Three dual-band antennas: 2 dipole (long); 1 patch (square)
•
Installation Guide
•
Resource CD which includes a link to the Reference Manual
•
Warranty/Support Information Card
Then, Set Up the WNDAP330
b.
The WNDAP330 user interface will
display
Connect the power adapter to the
WNDAP330 and verify the
following:
•
Power. The power light should be lit. If the power light is not lit, check the
connections and check to see if the power outlet is controlled by a wall
switch that is turned off.
•
Test. The test light blinks when the WNDAP330 is first turned on.
•
LAN. The LAN light on the WNDAP330 should be lit (no light for a 10
Mbps connection, amber for a 100 Mbps connection, and green for a 1000
Mbps connection). If not, make sure the Ethernet cable is securely attached
at both ends.
•
Wireless. The 802.11ng WLAN light should be lit.
2. Configure LAN and Wireless Access
a.
From your PC, configure the WNDAP330 Ethernet port for LAN access.
Connect to the WNDAP330 by opening your browser and entering
http://192.168.0.235 in the address field.
a.
Prepare a PC with an Ethernet adapter. If this PC is already part of your network,
record its TCP/IP configuration settings. Configure the PC with a static IP
address of 192.168.0.210 and 255.255.255.0 as the subnet mask.
c.
Select Configuration > System >
Basic > General from the menu and
configure the Access Point Name and select the appropriate Country/Region of
operation from the pull-down menu.
d.
Select Configuration > IP > Basic from the menu and configure the IP settings
for your network.
e.
Select Configuration > Wireless > Basic > Wireless Settings from the menu and
configure the wireless interface for wireless access.
f.
Then, select Configuration > Security > Basic from the menu and and click Edit
to configure the level of data encryption security for your network.
See the online help or the Reference Manual for full instructions. (A link to the
online Reference Manual is on your Resource CD.)
3. Test Wireless Connectivity
Using a PC with a wireless adapter configured according to the wireless settings you
just set in the WNDAP330, establish a wireless connection to the WNDAP330.
Now that you have finished the setup steps, you are ready to deploy the WNDAP330
in your network. If needed, you can now reconfigure the PC you used in step 1 back
to its original TCP/IP settings.
Now, Deploy the WNDAP330
1.
Disconnect the WNDAP330 and position it where you will deploy it. The best
location is elevated, such as wall mounted or on the top of a cubicle, at the center of
your wireless coverage area, and within line of sight of all the mobile devices.
2.
Position the antenna. Vertical positioning provides best side-to-side coverage.
Horizontal positioning provides best top-to-bottom coverage.
3.
Connect an Ethernet cable from your WNDAP330 Access Point to a LAN port on
your router, switch, or hub.
4.
Connect the power adapter to the wireless access point and plug the power adapter in
to a power outlet. The PWR, LAN, and Wireless LAN lights should light up.
http://192.168.0.235
1. Connect the wireless access point to your computer.
When prompted, enter admin for the
user name and password for the
password, both in lower case letters.
A login window will display.
Tip: The WNDAP330 supports Power Over Ethernet (PoE). If you have a switch that
provides PoE, you will not need to use the power adapter to power the WNDAP330.
This can be especially convenient when the WNDAP330 is installed in a high
location far away from a power outlet.
The WLAN lights are not lit.
The wireless access point antennas are not working.
Note: If you cannot connect, see to Troubleshooting Tips in this guide or the Reference
Manual on the Resource CD.
If both Wireless LAN activity lights stay off, disconnect the adapter from its power
source and then plug it in again. (Only one WLAN LED will be on since the AP does
not support concurrent 2.4Ghz (b/g band) and 5Ghz (a band) activity.)
Technical Support
•
Log in to the wireless access point and verify that the radio is turned on.
Thank you for selecting NETGEAR products.
•
Make sure the antennas are tightly connected to the WNDAP330.
•
Contact NETGEAR if the Wireless LAN lights remain off.
After completing setup and configuration, locate the serial number on the bottom label of
the wireless access point and use it to register your product at
http://www.netgear.com/register.
I cannot configure the access point from a browser.
Check these items:
•
Troubleshooting Tips
Here are some tips for correcting simple problems you may have.
•
Make sure the power cord is connected to the wireless access point and plugged in to
a working power outlet or power strip.
•
Make sure you are using the correct NETGEAR power adapter supplied with your
wireless access point.
The Ethernet light is not lit.
The WNDAP330 is properly installed, LAN connections are OK, and it is powered
on. Check that the LAN port LED is green to verify that the Ethernet connection is
OK.
•
If you are using the NetBIOS name of the WNDAP330 to connect, ensure that your
PC and the WNDAP330 are on the same network segment or that there is a WINS
server on your network.
•
If your PC uses a Fixed (Static) IP address, ensure that it is using an IP Address in the
range of the WNDAP330. The WNDAP330 default IP Address is 192.168.0.235 and
the default Subnet Mask is 255.255.255.0. The WNDAP330 default setting is for a
static IP address. If the network where you are connecting it is using DHCP, configure
it accordingly. See the Reference Manual on the Resource CD for the ProSafe
Wireless Access Point for more details.
No lights are lit on the access point.
The wireless access point has no power.
There is a hardware connection problem.
I cannot access the Internet or the LAN with a wireless capable
computer.
•
There is a configuration problem. Check these items:
•
Make sure the cable connectors are securely plugged in to the wireless access point
and to the network device (hub, switch, or router).
Make sure the connected device is turned on. (if the Ethernet link is a 10 Mbps link,
then the Ethernet LED will be off, but the Link/Act LED will be blinking if traffic is
present.
•
You may not have restarted the computer with the wireless adapter to have TCP/IP
changes take effect. Restart the computer.
•
The computer with the wireless adapter may not have the correct TCP/IP settings to
communicate with the network. Restart the computer and check that TCP/IP is set up
properly for that network. The usual setting for Windows on the Network Properties
is set to “Obtain an IP address automatically.”
•
February 2008
For full instructions on changing the default values of the wireless access point, see
the Reference Manual on the Resource CD for the ProSafe Wireless Access Point.
•
Finally, Verify Wireless Connectivity
Using a computer with an 802.11a/g wireless adapter, verify connectivity by using a
browser such as Netscape® or Microsoft® Internet Explorer to connect to the Internet, or
check for file and printer access on your network.
•
The wireless access point’s default values may not work with your network. Check
the wireless access point default configuration against the configuration of other
devices in your network.
Registration on the web site or over the phone is required before you can use our
telephone support service. The phone numbers for worldwide regional customer support
centers are on the Warranty and Support Information card that came with your product.
Go to http://www.netgear.com/support for product updates and web support.
This symbol was placed in accordance with the European Union Directive 2002/96 on the Waste
Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the European
Union, this product should be treated and recycled in accordance with the laws of your jurisdiction
implementing the WEEE Directive.
© 2008 by NETGEAR, Inc. All rights reserved. NETGEAR and the NETGEAR logo are registered trademarks
of NETGEAR, Inc. in the United States and/or other countries. Other brand and product names are trademarks or
registered trademarks of their respective holders. Information is subject to change without notice.
FCC Statement
CANADA STATEMENT
Operation is subject to the following two conditions:
(1) this device may not cause interference and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device
To prevent radio interference to the licensed service, this device is intended to be operated
indoors and away from windows to provide maximum shielding.
Note:
This device has been designed to operate with an antenna having a maximum gain of 2 dBi.
Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The
require antenna impedance is 50 ohms.
To reduce potential radio interference to other users, the antenna type and its gain should be
so chosen that the EIRP is not more than required for successful communication.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 4
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:75af9b95-6a6f-43a7-825a-3f3f9b518cae
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Create Date                     : 2008:02:12 16:20:32-08:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2008:05:27 19:14:51+08:00
Metadata Date                   : 2008:05:27 19:14:51+08:00
Document ID                     : uuid:eaa35659-8e43-4584-b623-72fac3ec57fa
Instance ID                     : uuid:52266082-115e-48c3-b6a6-9b8f17decb29
Format                          : application/pdf
Title                           : WNDAP330_IG.fm
Creator                         : bduvall
Author                          : bduvall

EXIF Metadata provided by EXIF.tools