Netgear orporated 09200107 RangeMax Dual Band Wireless-N USB Adapter User Manual FullManual

Download:
Mirror Download [FCC.gov]
Document ID	1131425
Application ID	2gAFJGYt0l8L5v97Ty54xg==
Document Description	manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	173.57kB (2169651 bits)
Date Submitted	2009-06-30 00:00:00
Date Available	2009-06-30 00:00:00
Creation Date	2008-12-05 14:22:19
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2009-06-04 11:40:03
Document Title	FullManual.book
Document Creator	FrameMaker 8.0
Document Author:	bduvall

NETGEAR RangeMax
Dual Band Wireless-N
USB Adapter
WNDA3100v2 User
Manual
NETGEAR, Inc.
350 East Plumeria Drive.
San Jose, CA 95134 USA
202-10426-01 Beta
December 2008
© 2008 by NETGEAR, Inc. All rights reserved.
Technical Support
Please refer to the support information card that shipped with your product. By registering your product at
http://www.netgear.com/register, we can provide you with faster expert technical support and timely notices of product
and software upgrades.
NETGEAR, INC. Support Information
Phone: 1-888-NETGEAR, for US & Canada only. For other countries, see your Support information card.
E-mail: support@netgear.com
North American NETGEAR website: http://www.netgear.com
Trademarks
NETGEAR, the NETGEAR logo, ProSafe, and Auto Uplink are trademarks or registered trademarks of NETGEAR, Inc.
Microsoft, Windows, Windows NT and Vista are registered trademarks of Microsoft Corporation.Other brand and
product names are registered trademarks or trademarks of their respective holders.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to
make changes to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit
layout(s) described herein.
Maximum Wireless Signal Rate Derived from IEEE Standard 802.11 Specifications
Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic,
building materials and construction, and network overhead, lower actual data throughput rate.
Safety and Regulatory Notices
FCC Statement
The WNDA3100v2 has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15
of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment or devices
ii
v1.0, December 2008
•
Connect the equipment to an outlet other than the receiver’s
•
Consult a dealer or an experienced radio/TV technician for assistance
FCC Caution: Any change or modification to the product not expressly approved by Netgear could void the user’s
authority to operate the device.
FCC RF Radiation Exposure and SAR Statements
SAR Statement
The NETGEAR WNDA3100v2 has been tested for body-worn Specific Absorption Rate (SAR) compliance. The FCC
has established detailed SAR requirements and has established that these requirements have been met while installed in
host notebook computer.
Important Note
To comply with RF exposure limits, user must not simultaneously operate wireless products in adjacent USB-ports or cardbus slots.
RF Exposure Information
The radio module has been evaluated under FCC Bulletin OET 65C (01-01) and found to be compliant to the
requirements as set forth in CFR 47 Sections, 2.1093, and 15.247 (b) (4) addressing RF Exposure from radio frequency
devices. This model meets the applicable government requirements for exposure to radio frequency waves. The highest
SAR level measured for this device was 1.19 W/kg.
Canadian Department of Communications Industry Canada (IC) Notice
This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Cet appareil numérique de la classe B
est conforme à la norme NMB-003 et CNR-210 du Canada.
“To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from
windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to
licensing.”
“Pour empêcher que cet appareil cause du brouillage au service faisant l’objet d’une licence, il doit être utilisé à
l’intérieur et devrait être placé loin des fenêtres afin de fournir un écran de blindage maximal. Si le matériel (ou son
antenne d’émission) est installé à l’extérieur, il doit faire l’objet d’une licence.”
Europe - EU Declaration of Conformity
A printed copy of the EU Declaration of Conformity certificate for this product is provided in the WNDA3100v2
product package.
Èesky
[Czech]
NETGEAR, Inc. tímto prohlašuje, že tento NETGEAR RangeMax Dual Band Wireless-N
USB Adapter WNDA3100v2 je ve shodì se základními požadavky a dalšími pøíslušnými
ustanoveními smìrnice 1999/5/ES.
Dansk
[Danish]
Undertegnede NETGEAR, Inc. erklærer herved, at følgende udstyr NETGEAR
RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 overholder de væsentlige
krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch
[German]
Hiermit erklärt NETGEAR, Inc., dass sich das Gerät NETGEAR RangeMax Dual Band
Wireless-N USB Adapter WNDA3100v2 in Übereinstimmung mit den grundlegenden
Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG
befindet.
iii
v1.0, December 2008
Eesti
[Estonian]
Käesolevaga kinnitab NETGEAR, Inc. seadme NETGEAR RangeMax Dual Band
Wireless-N USB Adapter WNDA3100v2 vastavust direktiivi 1999/5/EÜ põhinõuetele ja
nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
English
Hereby, NETGEAR, Inc., declares that this NETGEAR RangeMax Dual Band Wireless-N
USB Adapter WNDA3100v2 is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
Español
[Spanish]
Por medio de la presente NETGEAR, Inc. declara que el NETGEAR RangeMax Dual
Band Wireless-N USB Adapter WNDA3100v2 cumple con los requisitos esenciales y
cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Ελληνική
[Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ NETGEAR, Inc. ΔΗΛΩΝΕΙ ΟΤΙ NETGEAR RangeMax Dual
Band Wireless-N USB Adapter WNDA3100v2 ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ
ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/
ΕΚ.
Français
[French]
Par la présente NETGEAR, Inc. déclare que l'appareil NETGEAR RangeMax Dual Band
Wireless-N USB Adapter WNDA3100v2 est conforme aux exigences essentielles et aux
autres dispositions pertinentes de la directive 1999/5/CE.
Italiano
[Italian]
Con la presente NETGEAR, Inc. dichiara che questo NETGEAR RangeMax Dual Band
Wireless-N USB Adapter WNDA3100v2 è conforme ai requisiti essenziali ed alle altre
disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski
[Latvian]
Ar šo NETGEAR, Inc. deklarç, ka NETGEAR RangeMax Dual Band Wireless-N USB
Adapter WNDA3100v2 atbilst Direktîvas 1999/5/EK bûtiskajâm prasîbâm un citiem ar to
saistîtajiem noteikumiem.
Lietuviø
[Lithuanian]
Šiuo NETGEAR, Inc. deklaruoja, kad šis NETGEAR RangeMax Dual Band Wireless-N
USB Adapter WNDA3100v2 atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos
nuostatas.
Nederlands
[Dutch]
Hierbij verklaart NETGEAR, Inc. dat het toestel NETGEAR RangeMax Dual Band
Wireless-N USB Adapter WNDA3100v2 in overeenstemming is met de essentiële eisen
en de andere relevante bepalingen van richtlijn 1999/5/EG.
Malti
[Maltese]
Hawnhekk, NETGEAR, Inc., jiddikjara li dan NETGEAR RangeMax Dual Band WirelessN USB Adapter WNDA3100v2 jikkonforma mal-tiijiet essenzjali u ma provvedimenti orajn
relevanti li hemm fid-Dirrettiva 1999/5/EC.
Magyar
[Hungarian]
Alulírott, NETGEAR, Inc. nyilatkozom, hogy a NETGEAR RangeMax Dual Band
Wireless-N USB Adapter WNDA3100v2 megfelel a vonatkozó alapvetõ
követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Polski [Polish] Niniejszym NETGEAR, Inc. oœwiadcza, ¿e NETGEAR RangeMax Dual Band WirelessN USB Adapter WNDA3100v2 jest zgodny z zasadniczymi wymogami oraz pozosta³ymi
stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português
[Portuguese]
NETGEAR, Inc. declara que este NETGEAR RangeMax Dual Band Wireless-N USB
Adapter WNDA3100v2 está conforme com os requisitos essenciais e outras disposições
da Directiva 1999/5/CE.
iv
v1.0, December 2008
Slovensko
[Slovenian]
NETGEAR, Inc. izjavlja, da je ta NETGEAR RangeMax Dual Band Wireless-N USB
Adapter WNDA3100v2 v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloèili
direktive 1999/5/ES.
Slovensky
[Slovak]
NETGEAR, Inc. týmto vyhlasuje, že NETGEAR RangeMax Dual Band Wireless-N USB
Adapter WNDA3100v2 spåòa základné požiadavky a všetky príslušné ustanovenia
Smernice 1999/5/ES.
Suomi
[Finnish]
NETGEAR, Inc. vakuuttaa täten että NETGEAR RangeMax Dual Band Wireless-N USB
Adapter WNDA3100v2 tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja
sitä koskevien direktiivin muiden ehtojen mukainen.
Svenska
[Swedish]
Härmed intygar NETGEAR, Inc. att denna [utrustningstyp] står I överensstämmelse med
de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv
1999/5/EG.
Product and Publication Details
Model Number:
WNDA3100v2
Publication Date:
December 2008
Product Family:
Wireless-N USB Adapter
Product Name:
NETGEAR RangeMax Dual Band Wireless-N USB Adapter
WNDA3100v2
Home or Business Product:
Home
Language:
English
Publication Part Number:
202-10426-01
Publication Version Number:
1.0
v1.0, December 2008
vi
v1.0, December 2008
Contents
About This Manual
Conventions, Formats, and Scope ................................................................................... ix
How to Use This Manual ................................................................................................... x
How to Print This Manual .................................................................................................. x
Revision History ................................................................................................................ xi
Chapter 1
Basic Setup
What You Need Before You Begin ..................................................................................... 1
Verify System Requirements ....................................................................................... 1
Observe Wireless Location and Range Guidelines ..................................................... 2
What Is in the Box ............................................................................................................. 3
Placing the USB Adapter Cradle ....................................................................................... 3
Installing the WNDA3100v2 ............................................................................................... 4
Installing the WNDA3100v2 Software ......................................................................... 5
Connecting the Wireless-N USB Adapter ................................................................... 6
Using the Smart Wizard to Set Up Your Wireless-N USB Adapter ............................. 7
Monitoring Your Wireless Connection Status ................................................................... 12
WNDA3100v2 Icon ................................................................................................... 13
Wireless Assistant Status Bar ................................................................................... 13
Wireless-N USB Adapter LED ................................................................................... 15
Upgrading the WNDA3100v2 Software ........................................................................... 15
Removing the WNDA3100v2 Software ........................................................................... 16
Chapter 2
Network Connections and Wireless Security
Disabling the Windows Zero Configuration Utility .............................................................. 1
Using the Wireless Assistant to Manage Your Wireless-N USB Adapter .......................... 2
Viewing Wireless Networks in Your Area .................................................................... 2
Joining a Network Manually ........................................................................................ 4
Using WPS to Connect to a Wireless Network ........................................................... 5
vii
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
Creating Wireless Profiles ......................................................................................... 13
Starting a Computer-to-Computer (Ad Hoc) Network Connection ............................ 17
About Wireless Security .................................................................................................. 18
Wireless Network Name (SSID) and Security Settings ............................................. 18
Setting Up WPA-PSK Security .................................................................................. 19
Setting Up WEP Encryption Security ........................................................................ 20
Other Wireless Assistant Functions ................................................................................. 22
Statistics Settings ...................................................................................................... 23
About Your Wireless Assistant .................................................................................. 24
Advanced Settings .................................................................................................... 25
Chapter 3
Wireless Network Performance
Optimizing Wireless Performance ..................................................................................... 1
Optimizing Your Network Bandwidth ................................................................................. 2
SOHO Networking Technologies ................................................................................. 3
Assessing Your Network Speed Requirements ........................................................... 4
Chapter 4
Troubleshooting
Troubleshooting Tips ......................................................................................................... 1
Ad Hoc Mode Is Not Working Correctly ............................................................................. 3
Windows XP Occasional Connection Problems ................................................................ 3
Appendix A
Technical Specifications and Factory Default Settings
Technical Specifications ..................................................................................................... 1
Factory Default Settings .................................................................................................... 2
Appendix B
Related Documents
viii
v1.0, December 2008
About This Manual
The NETGEAR® RangeMax™ Dual Wireless-N USB Adapter WNDA3100v2 User Manual
describes how to install, configure and troubleshoot the NETGEAR RangeMax Dual Band
Wireless-N USB Adapter WNDA3100v2. The information in this manual is intended for readers
with intermediate computer and Internet skills.
Conventions, Formats, and Scope
The conventions, formats, and scope of this manual are described in the following paragraphs:
•
•
Typographical Conventions. This manual uses the following typographical conventions:
Italic
Emphasis, books, CDs, file and server names, extensions
Bold
User input, IP addresses, GUI screen text
Fixed
Command prompt, CLI text, code
italic
URL links
Formats. This manual uses the following formats to highlight special messages:
Note: This format is used to highlight information of importance or special interest.
Tip: This format is used to highlight a procedure that will save time or resources.
Warning: Ignoring this type of note may result in a malfunction or damage to the
equipment.
ix
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
•
Scope. This manual is written for the RangeMax Dual Band Wireless-N USB Adapter
WNDA3100v2 according to these specifications:
Product Version
NETGEAR RangeMax Dual Band Wireless-N USB Adapter
WNDA3100v2
Manual Publication Date
December 2008
For more information about network, Internet, firewall, and VPN technologies, see the links to the
NETGEAR website in Appendix B, “Related Documents.
Note: Product updates are available on the NETGEAR, Inc. website at
http://www.netgear.com/support.
How to Use This Manual
The HTML version of this manual includes the following:
•
Buttons,
at a time
and
, for browsing forwards or backwards through the manual one page
•
button that displays the table of contents and an
button. Double-click on a
link in the table of contents or index to navigate directly to where the topic is described in the
manual.
•
model.
•
Links to PDF versions of the full manual and individual chapters.
button to access the full NETGEAR, Inc. online knowledge base for the product
How to Print This Manual
To print this manual, you can choose one of the following options, according to your needs.
•
Printing a page from HTML. Each page in the HTML version of the manual is dedicated to
a major topic. Select File > Print from the browser menu to print the page contents.
•
Printing from PDF. Your computer must have the free Adobe Acrobat reader installed in
order to view and print PDF files. The Acrobat reader is available on the Adobe Web site at
http://www.adobe.com.
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
–
–
Printing a PDF chapter. Use the PDF of This Chapter link at the top left of any page.
•
Click the PDF of This Chapter link at the top left corner of any page in the chapter
you want to print. The PDF version of the chapter you were viewing opens in a
browser window.
•
Click the print icon in the upper left of your browser window.
Printing a PDF version of the complete manual. Use the Complete PDF Manual link at
the top left corner of any page.
•
Click the Complete PDF Manual link at the top left corner of any page in the manual.
The PDF version of the complete manual opens in a browser window.
•
Click the print icon in the upper left of your browser window.
Tip: If your printer supports printing two pages on a single sheet of paper, you can
save paper and printer ink by selecting this feature.
Revision History
Part Number
Version
Date
Number
202-10329-01
1.0
December
2007
202-10426-01
1.0
December
2008
Description
Product update: WiFi Protected Setup (WPS) feature added.
xi
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
xii
v1.0, December 2008
Chapter 1
Basic Setup
This chapter describes how to install your RangeMax Dual Band Wireless-N USB Adapter
WNDA3100v2 and set up basic wireless connectivity on your wireless local area network
(WLAN). Advanced wireless network set up is covered in “Network Connections and Wireless
Security” in Chapter 2.
Note: Indoors, computers can easily connect to 802.11 wireless networks at distances of
several hundred feet. Because walls do not always block wireless signals, others
outside your immediate area could access your network. It is important to take
steps to secure your network from unauthorized access. The wireless USB adapter
provides highly effective security features, which are covered in “About Wireless
Security” on page 2-18. Use the security features appropriate to your needs.
What You Need Before You Begin
You need to verify that your computer meets the minimum system requirements and identify the
wireless network settings of the WLAN where you will connect before you can set up your
wireless USB adapter and connect.
Verify System Requirements
Before installing the NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2,
please make sure that these minimum requirements have been met:
•
You must have a PC with a Pentium 300 MHz or higher compatible processor with an
available USB 2.0 or 1.1 port.
Note: The maximum speed of a USB v2.0 port is 480 Mbps. If your computer has a
USB v1.1 port, the WNDA3100v2 is limited to that port’s maximum speed,
which is 14 Mbps.
•
•
A CD drive.
5 Mbytes of free hard disk space.
1-1
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
•
Vista, Windows XP Home, or Windows XP Professional. Some versions of Windows ask for
the original Windows operating system installation files to complete the installation of the
WNDA3100v2 driver software.
Note: Windows XP users must install SP2 or install the KB822603 hot fix (update),
which fixes the USB 2.0 host controller driver. Go to the following link to install
the hot fix:
http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=
733dd867-56a0-4956-b7fe-e85b688b7f86
Observe Wireless Location and Range Guidelines
For best performance, place the wireless USB adapter at least 4 feet (over 1 meter) away from the
wireless router or access point.
Computers can connect over wireless networks indoors at a range that varies significantly based on
the physical location of the computer with the wireless USB adapter. For best results, avoid
potential sources of interference, such as the following:
• Large metal surfaces
• Microwaves
• 2.4 GHz or 5 GHz cordless phones
Note: If there is 2.4 GHz interference at your location, such as from a cordless phone, you
can change the setting to 5 GHz for better wireless throughput. See “Advanced
Settings” on page 2-25.
In general, wireless devices can communicate through walls. However, if the walls are constructed
with concrete, or have metal, or metal mesh, the effective range decreases if such materials are
between the devices.
1-2
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
What Is in the Box
The product package should contain the following items:
• NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2
• USB cable and adapter cradle
• Installation Guide
• Resource CD, including:
– The Smart Wizard Installation Assistant
– This manual
– Installation Guide
• Warranty and Support information card
If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the
carton, including the original packing materials, in case you need to return the product for repair.
Placing the USB Adapter Cradle
You can attach the wireless USB adapter directly to a USB port on your computer, or use the USB
cable to extend the range and obtain better wireless reception.
To use the USB cable, plastic cradle, and loop-and-hook fastener for better USB adapter
placement on a computer monitor:
1. The wireless USB adapter comes with three black fasteners. Locate the one with a prickly
side, and attach it to the plastic cradle on the middle of the outside rear.
Figure 1-1
1-3
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
2. Insert the wireless USB adapter in the plastic cradle, and connect the USB cable.
Figure 1-2
1. Place one of the other pieces of loop-and-hook fastener on the side or back of your monitor
near the top for better reception. Then join the pieces of the fastener to attach the USB adapter
in the plastic cradle to the monitor.
Figure 1-3
Installing the WNDA3100v2
To complete this installation you must:
1. Install the WNDA3100v2 software.
2. When prompted, insert the wireless USB adapter and follow the Windows XP Found New
Hardware wizard prompts (unless using Vista).
3. Set up the wireless USB adapter to connect to your wireless network.
1-4
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
If this is a new wireless network installation, use the factory default settings to set up the network
and verify wireless connectivity. If this is an addition to an existing wireless network, you must
identify the wireless network and wireless security settings that are already defined.
Your RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 basic factory default
settings are:
•
Network Name Service Set Identification (SSID), Any (First available network)
Note: For the RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 to
communicate with a wireless access point or wireless adapter, all devices must
be set up to use the same wireless network name (SSID).
•
Network mode (Infrastructure or Ad-hoc), Infrastructure
•
Data security WEP, WPA2-PSK, or WPA-PSK encryption, Enabled
Installing the WNDA3100v2 Software
Note: Do not connect the wireless USB adapter until you are prompted to do so.
To install the software:
1. Insert the Resource CD. If the Welcome screen does not open, browse the files on the CD, and
double-click Autorun.exe.
2. Click Install the Software.The Software Update Check screen displays:
Figure 1-4
1-5
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
3. If you are connected to the Internet, click Check for Updates. If not, you can choose to install
from the CD.
4. Follow the on-screen instructions to install the NETGEAR WNDA3100v2 software.
•
For Windows XP, if a Windows logo testing message appears, click Continue Anyway.
•
If a message that Windows Vista cannot verify the publisher of this driver displays, click
Install this driver software anyway.
5. When the NETGEAR Smart Wizard Installation Complete screen displays, click Next.
Connecting the Wireless-N USB Adapter
After you have installed the NETGEAR Smart Wizard, the following screen displays:
Figure 1-5
To connect your wireless USB adapter:
1. Locate an available USB port on your computer.
Note: If you do not have a USB 2.0 port on your computer, the throughput of the
WNDA3100v2 will be limited to the 14 Mbps of the USB 1.1 standard.
2. Insert the wireless adapter in a USB port on your computer.
•
For best results, put the wireless adapter at least 4 feet (1 meter) from your router.
•
To use the USB cable, connect it to the wireless USB adapter and a USB port. See
“Placing the USB Adapter Cradle” on page 1-3.
1-6
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
3. For Windows Vista computers, the adapter and driver are automatically added. Click Next and
then go to the following section “Using the Smart Wizard to Set Up Your Wireless-N USB
Adapter” on page 1-7. For Windows XP computers, the Found New Hardware Wizard
displays.
4. Follow the on-screen instructions for the Found New Hardware Wizard.
5. When the NETGEAR Smart Wizard screen returns, click Next.
Using the Smart Wizard to Set Up Your Wireless-N USB Adapter
After you have connected the wireless USB adapter, the following screen displays:
Figure 1-6
Windows XP or Vista users can set up the wireless adapter either with the NETGEAR Smart
Wizard (recommended) or the Windows configuration utilities.
•
NETGEAR Smart Wizard. Reveals more information about each network and makes it
easier to troubleshoot network connection problems.
•
Windows configuration utilities. See the Windows documentation or the NETGEAR
application note at: http://documentation.netgear.com/reference/enu/winzerocfg/index.htm.
To set up your wireless USB adapter with the NETGEAR Smart Wizard:
1. Click Next to proceed. You are prompted to let the wizard help you connect to a network
(recommended).
1-7
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
Figure 1-7
2. Click Next to proceed. The next screen that displays depends on whether there is a wireless
router or access point at your location that supports Wi-Fi Protected Setup (WPS).
Connecting to a WPS-Enabled Network
WPS allows you to automatically connect to a WPS-enabled network without having to enter a
password.
To connect to a WPS-enabled network:
1. Enable WPS on your router. Go to your router or access point and either press the WPS button
on the device or open the router utility and follow the instructions for adding a WPS client.
You have about 2 minutes to initiate the connection on the wireless USB adapter.
1-8
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
2. Press the WPS button on your wireless USB adapter, or press the soft WPS button on the
Smart Wizard screen.
Press to connect to a
WPS-enabled network
Figure 1-8
WPS activity LEDs will blink on both the router and the wireless USB adapter. A progress bar
on the adapter WPS screen indicates progress.
3. After the router has transmitted its wireless settings, a screen displays showing your settings.
Review your settings and then click Finish to connect to your network. A profile of your
wireless settings will be saved with the same profile name as your network (SSID) name.
Figure 1-9
1-9
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
Connecting to a Non-WPS-Enabled Network
If no WPS-enabled network is enabled:
1. A screen similar to this appears showing the available wireless networks.
Hidden network
Figure 1-10
Note: Hidden networks do not broadcast the network name (SSID). These networks
are in the drop-down list, but the Network Name (SSID) field is blank.
2. Select a wireless network, then click Next to proceed. If you select a secured network, the
Smart Wizard will detect it and you will be prompted to enter your passphrase. Click Next to
proceed.
Figure 1-11
3. A screen displays asking you whether you want to save a “profile” of your settings. Select
Yes, enter a profile name such as “home” or “work”, and click Next to proceed.
1-10
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
Home
Figure 1-12
4. A screen displays your settings for review. Click Back to make any changes, or click Finish to
save your profile and connect to your network.
Home
My Network
Figure 1-13
1-11
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
5. The Wireless Assistant screen displays. You are now connected to your wireless network.
Click Close to exist the Wireless Assistant.
Home
My Network
WPA2-PSK
Figure 1-14
The WNDA3100v2 icon
appears in the system tray. You can click it to access the Wireless
Assistant if you want to make any changes or connect to a different wireless network. The wizard
initiates your wireless connection, which could take up to a minute.
The Status Bar at the bottom of the Settings tab of the Wireless Assistant displays important details
about your wireless connection. See “Wireless Assistant Status Bar” on page 1-13.”
Monitoring Your Wireless Connection Status
The WNDA3100v2 has indicators in three locations that show the status of your connection to a
wireless network and to the Internet:
•
WNDA3100v2 icon. After you install the WNDA3100v2 software, the
icon appears on
the desktop and in the right on the Windows task bar. It is color coded to show the status of the
connection.
•
Wireless Assistant status bar. Clicking on the system tray icon opens the Wireless Assistant.
The status bar at the bottom of the screen shows details about your wireless and Internet
connection. See “Wireless Assistant Status Bar” on page 1-13.
•
Adapter LED status lights. The LED on the wireless USB adapter shows the network
connection. Solid indicates a connection. The LED blinks when the wireless USB adapter is
looking for a network association and when it is sending or receiving data. See “Wireless-N
USB Adapter LED” on page 1-15.
1-12
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
Note: The maximum speed of a USB v2.0 port is 480 Mbps. If your computer has a USB
v1.1 port, the WNDA3100v2 is limited to that port’s maximum speed, which is
14 Mbps.
WNDA3100v2 Icon
The WNDA3100v2 icon is on the desktop and in the Windows system tray. The system tray is on
one end of the task bar in the Microsoft Windows desktop. The WNDA3100v2 icon will change
colors depending on the condition of the adapter. The following table describes the various
conditions indicated by the color of the icon
Color
Condition
Description
Red
The wireless USB adapter
has no connection to any
other wireless node.
The wireless USB adapter cannot link to any other wireless
node, or the link is lost. Check your configuration, or try
moving to a location where the wireless signal quality is better.
Yellow
The wireless USB adapter
The wireless link is weak. Move to a better location, such as
has a connection with another closer to the wireless access point. Also, look for possible
wireless node.
interference such as a 2.4 GHz cordless phone or large metal
surface.
Green
The wireless USB adapter
The wireless USB adapter has established good
has a connection with another communication with an access point, and the signal quality is
wireless node.
strong.
Wireless Assistant Status Bar
For more information, you can view the Wireless Assistant status bar. Click the
icon to open
the Wireless Assistant. The Wireless Assistant Settings tab displays. The status bar is located at the
bottom of the Settings tab.
Security
Channel
Throughput
Signal
strength
Wireless
network
Join a Network
Connection status
Figure 1-15
1-13
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
The following table describes how to interpret the Wireless Assistant status bar.
Understanding the Status Bar
Wireless network
Identifies which wireless network you have joined.
Security
• A closed lock indicates that security is enabled.
• An open lock indicates an open network without wireless security.
Channel
The wireless channel used by the network. If many wireless networks in your
area use the same channel, they can interfere with one another.
Throughput
• To optimize wireless throughput, connect to a network with a high-speed
router or access point and a high-speed Internet connection.See Chapter 3,
“Wireless Network Performance.
• If there is wireless interference in the 2.4 GHz range, such as from a cordless
phone, use the Advanced Settings to select 5GHz. See “Advanced Settings”
on page 2-25.
• If your computer has a USB v1.1 port, the wireless USB adapter is limited to
that port’s maximum speed, which is 14 Mbps.
Signal strength
More dots indicates a stronger signal. Usually, you experience higher throughput
when the signal is strongest.
Join a Network
Click Join a Network to open the Connection Wizard.
Connection
status
The status of your network connection.
• Connected to Internet. The wireless Internet connection is OK.
• Connected to Router. The wireless connection to the router is OK, but the
router is not connected to the Internet.
169.254.x.x or ___.___.___.___. The wireless connection to the router is OK,
but there is a problem with the router. See the online help or Chapter 4,
“Troubleshooting.
The connection status is useful in isolating a problem. For example, if you are connected to a
router, but not to the Internet, then check the router’s Internet connection.
If you right-click the system tray icon, you can disable the Internet notification feature by clearing
the check mark enabling notification, as shown in the following figure. If you do so, then only the
IP address is shown.
Figure 1-16
1-14
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
In Vista, there is one more option: Enable NETGEAR Smart Wizard.
Figure 1-17
If you clear the check mark for Enable NETGEAR Smart Wizard, the NETGEAR Smart Wizard is
disabled, and you must set up the wireless adapter with Vista auto-configuration.
Wireless-N USB Adapter LED
The LED on the wireless USB adapter indicates the condition of the wireless link as explained in
the following table.
Wireless-N USB Adapter
The LED color changes
depending on the type of
network connection. Amber
indicates 2.4 GHz, and blue
indicates 5 GHz.
LED
Meaning
Off
• The wireless USB adapter in not plugged in to the USB port.
• The wireless USB adapter is in power save mode (default
from power up or reset).
Slow
blinking
• Alternating amber and blue. The wireless USB adapter is
scanning for a network.
• Amber. The wireless USB adapter is connecting to a
network at 2.4 GHz.
• Blue. The wireless USB adapter is connecting to a network
at 5 GHz.
Blinking
The wireless USB adapter is connected to a wireless network,
and is sending or receiving data.
Solid
The wireless USB adapter is connected to a wireless network,
but it is not sending or receiving data.
Upgrading the WNDA3100v2 Software
Upgrades may be available at the NETGEAR website. To install an upgrade, follow these steps.
1. Write down the settings for any profiles that you want to save. They will not be retained.
2. Download the upgrade from the NETGEAR website Support page.
3. Remove the previous WNDA3100v2 software from your computer.
4. Remove the WNDA3100v2 adapter from your computer, and if prompted restart your
computer.
1-15
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
5. Run the installer that you downloaded (the file ends in .exe).
6. Follow the installer instructions, and if prompted, restart your computer.
Removing the WNDA3100v2 Software
You can remove the wireless adapter software in these ways:
•
Select the Windows Start menu > RangeMax Dual Band Wireless-N USB Adapter
WNDA3100v2 program group > uninstall option, and then follow the screen prompts.
•
Select Windows Start menu >Control Panel > Add or Remove Program, and then select the
RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 option, and follow the screen
prompts.
1-16
v1.0, December 2008
Chapter 2
Network Connections and Wireless Security
This chapter explains how to use your Wireless-N USB Adapter to connect to your wireless local
area network (WLAN) and how to set up wireless security for the Wireless-N USB Adapter so that
it matches the wireless security settings for your network.
If you chose the Windows XP or Windows Vista Zero Configuration utility during installation,
and now you want to use the Smart Wizard that is installed on your PC, you must disable the
Windows utility. If you are working with the Vista configuration utility, see the NETGEAR online
application note at: http://documentation.netgear.com/reference/enu/winzerocfg/index.htm
Disabling the Windows Zero Configuration Utility
To disable the Windows Zero Configuration utility:
1. Attach the wireless adapter to a USB port for your computer.
2. In Windows, select Start > Network Connections.
3. Select Wireless Network Connection, right-click, and then select Properties.
Figure 2-1
4. Click the Wireless Networks tab. Then clear the Use Windows to configure my wireless
settings check box.
2-1
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
Using the Wireless Assistant to Manage Your Wireless-N
USB Adapter
These instructions explain how to use the NETGEAR WNDA3100v2 Wireless Assistant to change
the wireless USB adapter wireless settings.
When you install the software from the Resource CD, the
icon appears in the Windows system
tray located on the Windows taskbar. You can click this icon in the system tray at any time to use
the Wireless Assistant. This software automatically restarts when you reboot your computer.
The Wireless Assistant provides a complete and easy-to-use set of tools to:
• View details about wireless networks in your area.
• Choose the network that you want to use.
• Configure wireless settings for your wireless USB adapter.
• Save your wireless network settings in profiles.
• Remove or reinstall the wireless adapter software.
The following sections explain how to use the Wireless Assistant.
Viewing Wireless Networks in Your Area
You can use the Networks tab to view all available wireless networks in your area. You can also
scan to search for wireless networks and refresh the tab.
To view information about wireless networks:
1. Use the
icon to open the Wireless Assistant.
2-2
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
2. Click the Networks tab to display the following screen:
You can click a column
heading to sort.
If many networks use
the same channel they
can interfere with each
other. (A) indicates a 5 GHz
network, and (G) indicates a
2.4 GHz network.
The status bar shows
your network connection
and Internet connection.
Figure 2-2
The screen shows the following information for each network scanned:
•
Network Name (SSID). The name assigned to a wireless network. This is the same as the
SSID or ESSID configuration parameter. Note that as a security measure, some wireless
access points do not broadcast their SSID. In such cases, the SSID field is blank even though
the rest of the information is still displayed.
•
Channel. The channel determines which operating frequency is used. In this column (A)
indicates a 5 GHz network, and (G) indicates a 2.4 GHz network.
•
N. The access point supports wireless N mode.
•
WPS. The access point supports WPS.
•
Security. Identifies whether the wireless network uses security settings such as
WPA2-PSK, WPA-PSK, or WEP.
•
Signal. Identifies the signal strength of the communications.
•
MAC Address. Identifies the hardware address (MAC address) of the wireless device
broadcasting this information.
•
Mode. Identifies the type of wireless network — Access Point (Infrastructure) or Computerto-Computer (Ad Hoc)
The buttons located at the bottom of the Networks tab are:
• Help. Display online help.
•
Join a Network. View networks and join a network. See “Joining a Network Manually” on
page 2-4.
2-3
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
•
•
•
Connect. Connect to the network that you selected.
Scan. Check for wireless networks. Clicking Scan refreshes the screen.
Close. Close the window of the Wizard.
Joining a Network Manually
During the WNDA3100v2 software installation, the Wireless Assistant lists the available
networks. After installation you can use the Join a Network button on the Network tab at any time
to view the available networks and select the one that you want to use.
Note: Make sure that you know the wireless security settings for the network that you
want to use. For example, if a network uses WEP, you must know the WEP key in
order to connect to it. If you use secure networks frequently, set up profiles for each
network with the wireless network and security settings.
Depending on whether or not a wireless access point or router in the network supports Wi-Fi
Protected Setup (WPS), the Smart Wizard presents different screens.
To join a network:
1. Use the
icon to open the Wireless Assistant. On the status bar, click Join a Network. This
starts the Smart Wizard.
2. If the Smart Wizard detects an access point or router with WPS, it displays the WPS screen.
To connect manually (not using WPS), select No, and click Next.
3. Select a network from the drop-down list. If you select a hidden network, then you must enter
the SSID. Click Next.
Figure 2-3
2-4
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
4. Follow the steps of the wizard to specify the wireless security if used, and to create a profile.
5. Review your settings, and click Finish.
6. You can use the status bar to verify your network connection. For more information, see
“Wireless Assistant Status Bar” on page 1-13. Click Close to exit the Wireless Assistant.
Using WPS to Connect to a Wireless Network
If an access point or router in the wireless network that you are trying to connect to supports WPS,
you can use WPS to set up the wireless settings of your wireless USB adapter and connect securely
to the access point or router.
Note: The NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2
only supports WPS on Windows 2000, XP, XP x64 and Vista (32/64 bits).
An access point or router that supports WPS has a WPS symbol. Some NETGEAR products
include NETGEAR’s Push 'N' Connect feature. This feature is based on the Wi-Fi Protected Setup
(WPS) standard (for more information, see http://www.wi-fi.org). WPS automatically configures
the network name (SSID) and wireless security for the access point or router and the wireless USB
adapter. Note that WPS is not a new security feature—it makes existing security features easier to
configure.
To connect the wireless USB adapter to an access point or router that supports WPS, do one of the
following:
•
Connect during initial installation. See “Using the Smart Wizard to Set Up Your Wireless-N
USB Adapter” on page 1-7.
•
Open the Wireless Utility on your wireless router or access point and follow the instructions
for “Adding a wireless client.” Then, either
–
Push the WPS button on your wireless USB adapter, or
–
Use the
icon to open the Wireless Assistant. On the status bar, click Join a Network.
This starts the Smart Wizard.
There are two methods to connect using WPS:
•
Push Button Configuration (PBC). Press either a hard or soft button on your wireless access
point or router. Then, within 2 minutes, press the gray WPS button on your WNDA3100v2
wireless USB adapter—or click the on-screen WPS button in the adapter software.
2-5
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
•
PIN entry. Enter the router or access point security PIN, or use the WNDA3100v2 Smart
Wizard to generate a Personal Identification number (PIN) for the adapter that you can
associate with the access point or router.
Using the WPS Push Button to Connect to a Wireless Access Point or Router
To join a network using the WPS push button:
1. On the access point or router that you have selected, you must first depress the WPS button or
dome on the device. If the device doesn’t have a hard WPS button, open its Smart Wizard or
configuration utility and follow the instructions for adding a WPS client.
Note: Once you have initiated WPS from your router or access point, you have
approximately 2 minutes to initiate a WPS connection from your wireless USB
adapter. So, don’t depress the router/access point WPS button until you are
ready to activate the adapter WPS button.
2. Use the
icon in your system tray to open the adapter’s Wireless Assistant. On the status
bar, click Join a Network. This starts the Smart Wizard.
Figure 2-4
2-6
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
3. If the Smart Wizard detects an access point or router that is WPS-capable, it displays the WPS
screen. Select Yes, and click Next.
Figure 2-5
4. If your router or access point has a WPS push-button, select the Yes radio box and click Next.
Figure 2-6
5. Now, press the WPS button on your router or access point. Then, press the WPS push-button
on your wireless USB adapter on press the on-screen WPS button. The on-screen WPS button
will blink while the wireless settings are being transmitted from your router or access point to
your wireless USB adapter.
2-7
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
Figure 2-7
6. A snapshot of your wireless settings will display. A profile of your settings is created and
saved under the name of your wireless network (SSID) name. Click Finish to complete your
connection.
Figure 2-8
7. The Wireless Assistant displays showing the status of your connection and your signal
strength. Click Close to exist the Wireless Assistant.
2-8
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
Figure 2-9
You can use the Status Bar to verify your network connection. For more information, see
“Wireless Assistant Status Bar” on page 1-13.
8. Close the Smart Wizard or configuration utility on your access point or router.
Using a PIN to Connect to a Wireless Access Point or Router
If your router or access point does not have either a hard of soft push button, you can
•
Enter the PIN of the router or access point into the wireless USB adapter, or
•
The wireless USB adapter can automatically generate a PIN which you can then enter into
the wireless configuration utility of your router or wireless access point.
To use a PIN to connect to your wireless network:
1. Select the icon
from your system tray to open the Wireless Assistant. On the status bar,
click Join a Network.
2-9
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
Figure 2-10
2. If the Smart Wizard detects an access point or router that is WPS-capable, it displays the WPS
screen. Select Yes, and click Next.
Figure 2-11
2-10
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
3. If your router does not have a WPS push-button, select No, and click Next.
Figure 2-12
4. You can use the security PIN method to connect to the router or access point by either:
•
Entering the security PIN number of your router or access point in the Enter the AP’s
PIN field and clicking Next. The WPS process of discovering the router and transmitting
the router’s settings to the adapter will begin.
Figure 2-13
2-11
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
•
Or by checking the Generating a random Security PIN.... radio box and clicking Next,
The wireless USB adapter will generate a security PIN. Make note of the PIN. Then, enter
the security PIN, when instructed, into the configuration utility of the router or access
point.
Figure 2-14
5. After the wireless settings have been transmitted from the router or access point to the wireless
USB adapter, a snapshot of your wireless settings will display. A profile of these settings will
be created and given the same name (SSID) as your wireless network name. Click Finish to
connect to your network.
Figure 2-15
6. The Wireless Assistant displays showing the status of your connection and your signal
strength. Click Close to exist the Wireless Assistant.
2-12
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
Figure 2-16
You can use the Status Bar to verify your network connection. For more information, see
“Wireless Assistant Status Bar” on page 1-13.
Creating Wireless Profiles
The WNDA3100v2 Wireless Assistant uses profiles to store all the settings for a particular
wireless network. There are two special profile names: Default and Profile.
•
Default. The profile named Default automatically scans for any available network. You
cannot change this profile name.
•
Profile. If you do not enter a name in the Profile Name field, the name Profile is used to save
your settings. If you do this more than once, you are asked if you want to replace the previous
settings stored in Profile.
You can store multiple profiles and recall the one that matches the network you want to join.
If you use your computer to connect to different wireless networks, you can create a profile for
each wireless network. You can then easily load the profile that has all the settings that you need to
join the network you are using at the time.
There are two types of wireless network profiles that you can set up:
•
Access Point (Infrastructure). Connect to an access point or router with the 802.11
infrastructure mode.
•
Computer-to-Computer (Ad Hoc). Connect directly to another computer with the 802.11
Ad Hoc mode.
For more information about wireless network modes, see the wireless reference document at:
http://documentation.netgear.com/reference/enu/wireless/index.htm.
2-13
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
Setting Up a Profile to Connect to an Access Point or Router
Follow these instructions to set up the RangeMax Dual Band Wireless-N USB Adapter
WNDA3100v2 to connect to a wireless access point or router.
1. Use the
icon to open the Wireless Assistant. The Settings tab displays:
Figure 2-17
2. Enter the network settings.
a. In the Network Type section, make sure that Access Point (Infrastructure) is selected.
b. In the Profile field, type the name of the profile.
c. In the Network Name (SSID) field, select a network or enter the SSID.
Note: You will not get a wireless network connection unless the network SSID
matches exactly the SSID used by the access point.
3. Save your settings in a Profile.
a. Click Save Profile.
All the configuration settings are saved in this profile.
b. Click Apply, then click Close to exit, or click Cancel to return to the previous settings.
4. Verify wireless connectivity to your network.
2-14
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
Use a browser to connect to the Internet, or check for file and printer access on your network.
You can check the status bar in the Wireless Assistant for the current connection status.
Note: If you cannot connect, see Chapter 4, “Troubleshooting”. For problems with
accessing network resources, the Windows client and file and print sharing
software might not be installed and configured correctly on your computers.See the
link to “Internet Networking and TCP/IP Addressing:” in Appendix B.
Setting up a Computer-to-Computer (Ad Hoc) Profile
The Computer-to-Computer setting uses Ad Hoc mode. Ad Hoc mode is an 802.11 networking
framework in which devices or computers communicate directly with each other, without the use
of an access point. For example, this mode is used when two Windows computers are configured
with file and print sharing enabled and you want to exchange files directly between them.
Note: Ad Hoc mode does not work using DHCP settings. Ad Hoc mode requires either
static IP addresses (such as 192.168.0.1) or the IPX protocol. For help setting up
static IP addresses, see the PC Networking Tutorial on the Resource CD.
To create an Ad Hoc mode profile:
1. Use the
icon to open the Wireless Assistant. The Settings tab displays:
Figure 2-18
2. Enter the network settings.
a. Select Computer-to-Computer (Ad Hoc) for the network type.
b. Select or enter the network name (SSID) for the Ad Hoc network.
2-15
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
c. In the Profile field, type the name of the profile.
d. Click Apply.
3. Save your settings in a profile.
a. Click Save Profile, and all the configuration settings are saved in this profile.
b. Click Apply, then click Close to exit the Smart Wizard, or click Cancel to return to the
previous settings.
4. Configure the computer network settings.
a. Configure each computer with either a static IP address or with the IPX protocol.
b. Restart the computers.
5. Verify wireless connectivity between your peer devices with the ping program:
a. On the Windows taskbar, select Start > Run.
Figure 2-19
b. Assuming the target PC is configured with 192.168.0.1 as its IP address, type:
ping -t 192.168.0.1
and then click OK.
c. A continuous ping will be sent to the device with the 192.168.0.1 static IP address. The
ping response will change to Reply.
Figure 2-20
2-16
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
At this point the connection is established.
Note: If you cannot connect, see “Removing the WNDA3100v2 Software” in Chapter 1.
For problems accessing network resources, the Windows client and rile and print
sharing software might not be installed or configured correctly on your computers.
See the link to “Internet Networking and TCP/IP Addressing:” in Appendix B.
Starting a Computer-to-Computer (Ad Hoc) Network Connection
1. On the Settings tab of the Smart Wizard, select or type the network name (SSID).
2. Select the Computer-to-Computer (Ad Hoc) network type.
Note: for Windows Vista computers, you must have administrator rights. Otherwise,
this option is not available for selection.
3. Click Initiate Ad Hoc. The Ad Hoc Setting screen displays:
Figure 2-21
4. In the Start Ad Hoc drop-down list, select the wireless standard (802.11a, 802.11b, or
802.11g) for your Ad Hoc computer-to-computer network.
5. In the Channel drop-down list, select Automatic unless you notice interference problems. If
you experience interference with another nearby wireless device, select a channel that is not
being used by any other wireless networks near your wireless adapter. Use the Networks tab to
view the channels in use in your area.
6. Click OK.
Note: The channel number differs depending on the country. The connection speed
automatically defaults to the highest speed.
2-17
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
About Wireless Security
Many networks use wireless security to encrypt wireless data communications. If you try to
connect to a network with wireless security, the Smart Wizard detects it. Before you can use that
network, you must set up the WNDA3100v2 with exactly the same kind of wireless security
settings. If you use the Smart Wizard to set up security, you can take advantage of Push 'N'
Connect (WPS) to set up WPS2/WPA security (see “Using WPS to Connect to a Wireless
Network” on page 2-5). Otherwise, you can select from the following main types of wireless
security used for home networks:
• Wi-Fi Protected Access 2 Pre-Shared Key (WPA2-PSK)
• Wi-Fi Protected Access Pre-Shared Key (WPA-PSK)
• Wired Equivalent Privacy (WEP)
For more information about wireless security, see the wireless reference document at
http://documentation.netgear.com/reference/enu/wireless/index.htm.
You can strengthen the security of your wireless connection by enabling Wired Equivalent Privacy
(WEP) encryption of the wireless data communications, or you can use WPA-PSK (Wi-Fi
Protected Access Pre-Shared Key) encryption. For more information about wireless security, see
the link to “Wireless Communications:” in Appendix B.
In addition to the WNDA3100v2 wireless security features, NETGEAR recommends that you also
configure appropriate LAN network security features such as requiring a user name and password
to access the shared resources in your network.
Wireless Network Name (SSID) and Security Settings
Print this form, fill in the configuration parameters, and put it in a safe place for possible future
reference. For an existing wireless network, the person who set up the network can provide this
information.
•
Network Name (SSID). The service set Identification (SSID) identifies the wireless local area
network. Any (First available network) is the default WNDA3100v2 wireless network name
(SSID). You may customize it using up to 32 alphanumeric characters. Write your customized
wireless network name (SSID) on the line below.
Note: The SSID in the wireless access point is the SSID you configure in the wireless
USB adapter. For the access point and wireless nodes to communicate with
each other, all must be configured with the same SSID.
2-18
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
Wireless network name (SSID): ______________________________
•
If WPA2-PSK or WPA-PSK authentication is used:
–
•
Passphrase: ______________________________ These characters are case-sensitive.
Enter a word or group of printable characters. When you use WPA-PSK, the other devices
in the network cannot connect unless they are set to WPA-PSK as well, and are configured
with the correct passphrase.
If WEP authentication is used:
–
WEP encryption key size. Identify one: 64-bit or 128-bit. The encryption key size must
match the wireless network settings.
–
Data encryption (WEP) keys. There are two methods for creating WEP data encryption
keys. Whichever method you use, record the key values in the spaces below.
• Passphrase method: ______________________________ These characters are
case-sensitive. Enter a word or group of printable characters and click the Generate
Keys button. Not all wireless devices support the passphrase method.
• Manual method. These values are not case sensitive. For 64-bit WEP, enter 10 hex
digits (any combination of 0–9 or a–f). For 128-bit WEP, enter 26 hex digits.
Key 1: _____________________________ Key 2: _____________________________
Key 3: _____________________________ Key 4: _____________________________
Setting Up WPA-PSK Security
To configure WPA-PSK security:
1. Run the WNDA3100v2 Wireless Assistant.
a. Make sure that the WNDA3100v2 software is installed and the wireless USB adapter is
fully inserted in a USB port in your computer.
2-19
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
b. Use the
icon to open the Wireless Assistant. The Settings tab displays:
Figure 2-22
2. Configure the Security settings.
a. In the Profile field, select the profile, or type in a profile name.
b. In the Network Name (SSID) field, and then select the network, or enter the SSID.
Note: You will not get a wireless network connection unless the network SSID
matches exactly what is configured in the access point.
c. In the Security section, select WPA2-PSK [AES], and enter the passphrase.
For more about WPA2-PSK, see the link to “Wireless Communications:” in Appendix B.
3. Save your settings in a profile.
a. Click the Save Profile button. All the configuration settings are saved in this profile.
b. Click Apply, and then click Close to exit the Wireless Assistant.
Setting Up WEP Encryption Security
Follow the steps below to configure WEP encryption security:
1. Run the WNDA3100v2 Wireless Assistant.
a. Make sure that the WNDA3100v2 software is installed and the wireless USB adapter is
connected to the USB port in your computer.
2-20
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
b. Use the
icon to open the Wireless Assistant. The Settings tab displays:
Figure 2-23
2. Configure the Security settings.
a. In the Profile field, select the profile or type in a profile name.
b. In the Network Name (SSID) field, select the network, or enter the SSID.
Note: You will not get a wireless network connection unless the network SSID
matches exactly what is configured in the access point.
c. In the Security section, select WEP.
3. Select the WEP encryption strength you will use.
• 64-bit WEP data encryption
• 128-bit WEP data encryption
Note: Larger encryption keys require more processing and may slow the
communications response times.
2-21
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
4. Select Create with Passphrase, and enter the passphrase. The Wireless Assistant
automatically generates the WEP keys.
Note: The characters are case-sensitive. Be sure to use the same passphrase for all the
wireless devices in the network.
If the passphrase method is not available in the other devices, you must manually enter the
keys to match exactly what is in the access point and other 802.11b wireless devices.
5. Save your settings in a profile.
a. Click the Save Profile button. All the configuration settings are saved in this profile.
b. Click Apply.
c. Click Close to exit the Wireless Assistant.
Other Wireless Assistant Functions
The Wireless Assistant provides the ability to track transmit and send use statistics to monitor
trend data through your router. It also provides some advanced settings capabilities, which
NETGEAR recommends you use with caution.
2-22
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
Statistics Settings
The Statistics tab provides real time and historical trend information about the data traffic and
performance of your wireless adapter.
Figure 2-24
•
•
•
•
Transmit/Receive Performance (%). A real-time graph identifies the total, receive, and
transmit utilization as a percentage the total possible.
Transmit, Receive, and Total (TxRx). Radio buttons let you select whether to display the
transmit performance, the receive performance, or both in the same graph.
Transmit Statistics. Identifies transmit megabits per second (Mbps), transmit packets per
second (Tx Packets/s), total transmitted packets, and transmit errors.
Receive Statistics. Identifies receive megabits per second (Mbps), receive packets per second
(Rx Packets/s), total received packets, and reception errors.
2-23
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
About Your Wireless Assistant
The About tab displays the current version information.
Figure 2-25
The following information is displayed in the About tab:
•
Regional Domain. This is the region setting for the wireless adapter. The approved channels
for the region are automatically scanned. Governments regulate the channels used for wireless
transmission. Operating the wireless adapter in a different region might violate local laws.
•
Driver Version. The wireless adapter driver version.
•
Driver Date. The wireless adapter driver release date.
•
MAC Address. The MAC address of the adapter. The Media Access Control address is a
unique 48-bit hardware address assigned to every network interface card. Some wireless
networks restrict access based on a list of known MAC addresses. If you are communicating
with such a network, you must provide the address shown here to the network administrator
before you are allowed to connect. Restricting access by MAC address adds an obstacle
against unwanted access to your network. However, unless you use data encryption security,
the data broadcast over the wireless link is fully exposed.
•
IP Address. The IP address assigned to this adapter.
•
Smart Wireless Utility. The version and release date of the Wireless Assistant.
2-24
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
Advanced Settings
You can use the Advanced Settings screen to configure the preamble (GHz) that the adapter uses.
The available settings are Auto, 2.4 GHz, and 5 GHz. You can use the 5GHz range to avoid
interference in the 2.4GHz range. The 2.4GHz range is commonly used by cordless telephones.
Note: The default settings for the Fragmentation Threshold field and RTS/CTS
Threshold field usually work fine. Do not change them unless you have a specific
reason to do so.
By changing the preamble setting, you have the option to connect to the following types of
wireless networks.
• 2.4 GHz + 5GHz. Connect to both 2.4GHz and 5GHz access points, up to 300 Mbps.
• 2.4 GHz only. Connect only to 2.4GHz access points, up to 300 Mbps.
• 5 GHz only. Connect only to 5 GHz access points, up to 300 Mbps.
• 2.4 GHz. Connect to 802.11b/g access points, up to 54 Mbps.
• 5 GHz. Connect to 802.11a access points, up to 54 Mbps.
To change the preamble (GHz) setting:
1. On the Settings tab, click the Advanced Settings button to display the following screen.:
Figure 2-26
Note: for Windows Vista computers, you must have administrator rights. Otherwise,
this option is not available for selection.
2. In the Advanced section of the screen, select the setting that you want from the drop-down list.
2-25
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
Changing the setting in the Preamble field affects which options are available in the Wireless
Mode section of this screen. You can change the preamble for better throughput if you
experience interference, such as from a cordless telephone. Many cordless phones use 2.4
GHz, but some use 5 GHz or 6 GHz.
•
Auto. Up to 300 Mbps (2.4 GHz and 5 GHz).
•
Short. Use a 2.4 GHz preamble.
•
Long. Use a long preamble for 5 GHz networks.
3. Click OK.
2-26
v1.0, December 2008
Chapter 3
Wireless Network Performance
This chapter explains how to use your RangeMax Dual Band Wireless-N USB Adapter
WNDA3100v2 to connect to your wireless local area network (WLAN) and how to maximize the
performance of your WNDA3100v2 within your network. Included are scenarios for setting up
your network in a mixed use environment and the trade-off of using different types of
technology—wireless, wired, Powerline, etc.
Optimizing Wireless Performance
The speed and operating distance or range of your wireless connection can vary significantly based
on the location of the wireless router. Choose a location for your router that will maximize the
network speed.
The following list describes how to optimize wireless router performance.
•
Identify critical wireless links.
If your network has several wireless devices, decide which wireless devices need the highest
data rate, and locate the router near them. Many wireless products have automatic data-rate
fallback, which allows increased distances without losing connectivity. This also means that
devices that are farther away mighty be slower. Therefore, the most critical links in your
network are those where the traffic is high and the distances are great. Optimize those first.
•
•
Choose placement carefully. For best results, place your router:
–
Near the center of the area in which your computers will operate.
–
In an elevated location such as a high shelf where the wirelessly connected computers
have line-of-sight access (even if through walls).
Avoid obstacles to wireless signals.
–
Keep wireless devices at least two feet from large metal fixtures such as file cabinets,
refrigerators, pipes, metal ceilings, reinforced concrete, and metal partitions.
–
Keep the devices away from large amounts of water such as fish tanks and water coolers.
3-1
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
•
Reduce interference.
Avoid windows unless communicating between buildings. Place wireless devices away from
various electromagnetic noise sources, especially those in the 2400–2500 MHz frequency
band. Common noise-creating sources are:
•
–
Computers and fax machines (no closer than 1 foot)
–
Copying machines, elevators, and cell phones (no closer than 6 feet)
–
Microwave ovens (no closer than 10 feet)
Choose your settings.
– Use a scanning utility to determine what other wireless networks are operating nearby, and
choose an unused channel.
– Turn off SSID Broadcast, and change the default SSID. Other nearby devices might
automatically try to connect to your network several times a second, which can cause
significant performance reduction.
Optimizing Your Network Bandwidth
The speed of network connections depends on the type of equipment that you use. Try to use highspeed technologies for network connections with the heaviest traffic to avoid lower-speed
bottlenecks in the path. Figure 3-1 on page 3-3 shows a home network that includes many different
connection speeds.
In this network, the two PCs with gigabit (1000 Mbps) Ethernet adapters have a gigabit connection
through the router to the storage server. With a high-speed router this connection allows for
extremely fast backups or quick access to large files on the server. The PC connected through a
pair of Powerline HD adapters is limited to the 200 Mbps speed of the Powerline HD connection.
Although any of the links in this example would be sufficient for high-traffic applications such as
streaming HD video, the use of older devices such as 10 Mbps Ethernet or 802.11b wireless would
create a significant bottleneck.
3-2
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
Figure 3-1
In planning your network, think about which tasks will have the heaviest traffic flow between
them. Examples are:
• A media center in one room streaming high-definition video from a server in another room
• A storage device that is used for backing up your computers
SOHO Networking Technologies
Common connection types and their speed and security considerations are:
•
Broadband Internet
Your Internet connection speed is determined by your modem type, such as ADSL or cable
modem, as well as the connection speed of the sites to which you connect, and general Internet
traffic. ADSL and cable modem connections are asymmetrical, meaning they have a lower
data rate to the Internet (upstream) than from the Internet (downstream). Keep in mind that
when you connect to someone else who also has an asymmetrical connection, the data rate
between your sites is limited by each side’s upstream data rate. A typical residential ADSL or
cable modem connection provides a downstream throughput of about 1 to 3 megabits per
second (Mbps). Newer technologies such as ADSL2+ and Fiber to the Home (FTTH) l
increase the connection speed to tens of Mbps.
3-3
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
•
Wireless
A high-speed wireless router can provide a wireless data throughput of up to 300 Mbps using
technology called multiple-input multiple-output (MIMO), in which multiple antennas
transmit multiple streams of data. The use of multiple antennas also provides excellent range
and coverage. With the introduction of the newer WPA and WPA2 encryption and
authentication protocols, wireless security is extremely strong.
To get the best performance, use newer adapters such as RangeMax adapters for your
computers. A high-speed router might be compatible with older 802.11b and 802.11g adapters,
but the use of these older wireless technologies in your network can result in lower throughput
overall (typically less than 10 Mbps for 802.11b and less than 40 Mbps for 802.11g). In
addition, many older wireless products do not support the latest security protocols, WPA and
WPA2.
•
Powerline
For connecting rooms or floors that are blocked by obstructions or are distant vertically,
consider networking over your building’s AC wiring. NETGEAR’s Powerline HD family of
products delivers up to 200 Mbps to any outlet, while the older-generation XE family of
products delivers 14 Mbps or 85 Mbps. Data transmissions are encrypted for security, and you
can configure an individual network password to prevent neighbors from connecting.
The Powerline HD family of products can coexist on the same network with older-generation
XE family products or HomePlug 1.0 products, but they are not interoperable with these
older products.
•
Wired Ethernet
As Gigabit Ethernet ports become common on newer computers, wired Ethernet remains a
good choice for speed, economy, and security. Gigabit Ethernet can extend up to 100 meters
with twisted-pair wiring of CAT-5e or better. A wired connection is not susceptible to
interference, and eavesdropping would require a physical connection to your network.
Note: Actual data throughput will vary. Network conditions and environmental factors,
including volume of network traffic, building materials and construction, and
network overhead, can lower actual data throughput rate.
Assessing Your Network Speed Requirements
Because your Internet connection is likely to operate at a much lower speed than your local
network, faster local networking technologies might not improve your Internet experience.
However, many emerging home applications require high data rates. For example:
3-4
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
•
Streaming HD video requires 10 to 30 Mbps per stream. Because latency and packet loss can
disrupt your video, plan to provide at least twice the capacity you need.
•
Streaming MP3 audio requires less than 1 Mbps per stream and does not strain most modern
networks. Like video, however, streaming audio is also sensitive to latency and packet loss, so
a congested network or a noisy link can cause problems.
•
Backing up computers over the network has become popular due to the availability of
inexpensive mass storage. Table 3-1 shows the time to transfer 1 gigabyte (1 GB) of data using
various networking technologies.
Table 3-1. Theoretical Transfer Time for 1 Gigabyte
Network Connection
Theoretical Raw Transfer Time
Gigabit Wired Ethernet
8 seconds
RangeMax Dual Band Wireless-N
26 seconds
Powerline HD
40 seconds
100 Mbps Wired Ethernet
80 seconds
802.11g wireless
150 seconds
802.11b wireless
700 seconds
10 Mbps Wired Ethernet
800 seconds
Cable Modem (3 Mbps)
2700 seconds
Analog Modem (56 kbps)
144,000 seconds (40 hours)
3-5
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
3-6
v1.0, December 2008
Chapter 4
Troubleshooting
This chapter provides information about troubleshooting your RangeMax Dual Band Wireless-N
USB Adapter WNDA3100v2. For information about connecting to wireless networks and the
Internet, see “Basic Setup” in Chapter 1.
Troubleshooting Tips
Use the following information to solve common problems you may encounter. Also, refer to the
knowledge base on the NETGEAR website at http://www.netgear.com/support/main.asp.
Table 4-1. Troubleshooting Tips
Problem
Action
The LED is not lit.
The WNDA3100v2 is not connected to the USB port correctly
or the WNDA3100v2 software is not loaded.
• Remove and reinsert the WNDA3100v2.
• Check the Windows device manager to see if the
WNDA3100v2 is recognized and enabled. Reload the
WNDA3100v2 software, if necessary.
• Try to install the WNDA3100v2 in a different USB slot on
your system if one is available.
The LED blinks, but the WNDA3100v2 is
not connected to an access point.
The WNDA3100v2 is trying to connect to an access point, but
cannot connect.
• The access point might not be powered on.
• The access point and the WNDA3100v2 are not configured
with the same wireless parameters. Check the SSID and
wireless security settings.
I cannot connect to an access point.
The access point is available, and there is
good signal strength.
• If the access point is WPA-PSK protected, you need the
correct WPA-PSK passphrase. Otherwise, the
WNDA3100v2 is still connected to the previous access
point, and you cannot change to the WPA-PSK access
point.
• If the access point is WEP protected (either 64- or 128- bit
encryption), you are prompted to enter the WEP encryption
security information.
4-1
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
Table 4-1. Troubleshooting Tips (continued)
Problem
Action
Throughput is only 54 Mbps or only 14
Mbps.
The RangeMax Dual Band Wireless-N USB Adapter
WNDA3100v2 can operate at faster speeds.
• At 54 Mbps you are probably connecting to a standard
802.11g network. See Chapter 3, “Wireless Network
Performance”.
• If you do not have a USB 2.0 port on your PC, the
throughput is limited to the 14 Mbps of the USB 1.1
standard.
The Smart Wizard keeps asking me to save If you change the settings, the Smart Wizard offers you the
settings.
chance to save the changes. To avoid this prompt, simply
click Apply before you close the Smart Wizard.
Two WNDA3100v2 icons are in the system
tray.
You have an older software version installed on your system
and it needs to be removed. See “Removing the
WNDA3100v2 Software” in Chapter 1 or “Upgrading the
WNDA3100v2 Software” in Chapter 1.
I can connect to the access point, but not to This could be a physical layer problem or a network
the other computers on the network or to
configuration problem.
1. Check to make sure that the access point is physically
the Internet.
connected to the Ethernet network.
2. Make sure that the IP addresses and the Windows
networking parameters are all configured correctly. See
the link to “Internet Networking and TCP/IP Addressing:” in
Chapter B.
3. Restart the cable or DSL modem, router, access point, and
computer.
How can I view the IP address for the
wireless USB adapter?
To view the RangeMax Dual Band Wireless-N USB Adapter
WNDA3100v2 IP address, click the WNDA3100v2 icon to
open the Wireless Assistant. Then check the IP address in the
About page.
No IP address is assigned to the RangeMax This can occur if you upgraded your RangeMax Dual Band
Dual Band Wireless-N USB Adapter
Wireless-N USB Adapter WNDA3100v2 software and did not
WNDA3100v2.
reboot your system.
• Either restart your computer, or connect to a different access
point.
• It does not usually help to shut down the Wireless Assistant
or disable or enable the wireless USB adapter.
4-2
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
Ad Hoc Mode Is Not Working Correctly
You must click the Initiate Ad Hoc button before you click Apply. Here is how you start an Ad
Hoc network:
1. Fill in the Network Name (SSID) field.
2. Select the Computer-to-Computer (Ad Hoc) network type.
3. Click Initiate Ad Hoc.
4. Accept the default settings, or make your changes and click OK.
5. Click Apply.
Note: Be sure that all computers in your Ad Hoc network are configured with static IP
addresses in the same subnet.
Windows XP Occasional Connection Problems
Windows XP users who apply Windows XP Hotfix (SP2) Q815485 from the Windows XP Update
Service might not be able to connect to the Internet, might have dropped wireless connections, or
both when using the RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2. You can
delete this Hotfix from the Add or Remove Programs utility in the Control Panel.
To delete Windows XP Hotfix (SP2) Q815485:
1. Select Start > Control Panel > Add/Remove Programs.
2. Select Windows XP Hotfix (SP2) Q815485, and then click Remove.
•
You might receive an error message that states that some program on the computer may
not work correctly if the update is removed.
•
You can ignore this error message, and then click Yes to remove the update.
3. Restart your computer, and rerun the Smart Display Setup Wizard.
This will solve your connection issue. You can restore this hotfix by following this link:
http://microsoft.com/downloads/details.aspx?FamilyId=009D8425-CE2B-47A4-ABEC274845DC9E91&displaylang=en
4-3
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
4-4
v1.0, December 2008
Appendix A
Technical Specifications and Factory Default
Settings
Technical Specifications
The following table provides technical specifications for the wireless USB adapter.
Antenna
2 integrated internal wireless antennas
Standards
802.11a, 802.11n draft 2.0, 802.11g, or 802.11b
Radio Data Rate
1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54, 08, 140, 246, and 300 Mbps
(Auto Rate Sensing)
Frequency
2.4 GHz to 2.5 GHz CCK and OFDM Modulation); 5 GHz
Power
5V Bus powered
Emissions
FCC, CE
Bus interface
USB 2.0
Provided drivers
Microsoft Vista, Windows XP
Operating Environment
Operating temperature: 0 to 40 C
Encryption
40-bit (also called 64-bit) and 128-bit WEP data encryption, and WPA-PSK
Warranty
Limited 1-year warranty
A-1
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
Factory Default Settings
The following table lists the default settings of your wireless USB adapter.
Feature
Description
Smart Wizard
Enabled
Wireless
Wireless Communication
Enabled
Wireless Network Name (SSID)
Any (will connect to first wireless network that responds)
Security
Disabled
Network Type
Infrastructure
Transmission Speed
Autoa
Country/Region
United States (varies by region)
Operating Mode
802.11a, 802.11n, 802.11g, 802.11b
Data Rate
Up to 300 Mbps
a. Maximum wireless signal rate (IEEE Standard 802.11). Actual throughput will vary. Network conditions
and environmental factors, including volume of network traffic, building materials and construction, and
network overhead, lower actual data throughput rate.
A-2
v1.0, December 2008
Appendix B
Related Documents
This appendix provides links to reference documents you can use to gain a more complete
understanding of the technologies used in your NETGEAR product.
Document
Link
Windows XP and Vista
Wireless Configuration
Utilities Application Note
http://documentation.netgear.com/reference/enu/winzerocfg/
index.htm
Internet Networking and
TCP/IP Addressing:
http://documentation.netgear.com/reference/enu/tcpip/index.htm
Wireless Communications:
http://documentation.netgear.com/reference/enu/wireless/index.htm
Preparing a Computer for
Network Access:
http://documentation.netgear.com/reference/enu/wsdhcp/index.htm
Virtual Private Networking
(VPN):
http://documentation.netgear.com/reference/enu/vpn/index.htm
Glossary:
http://documentation.netgear.com/reference/enu/glossary/index.htm
B-1
v1.0, December 2008
NETGEAR RangeMax Dual Band Wireless-N USB Adapter WNDA3100v2 User Manual
B-2
v1.0, December 2008

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Page Mode                       : UseOutlines
XMP Toolkit                     : 3.1-701
Create Date                     : 2008:12:05 14:22:19Z
Creator Tool                    : FrameMaker 8.0
Modify Date                     : 2009:06:04 11:40:03+08:00
Metadata Date                   : 2009:06:04 11:40:03+08:00
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Format                          : application/pdf
Title                           : FullManual.book
Creator                         : bduvall
Document ID                     : uuid:0da7692f-51f7-4953-8660-25f5f4361603
Instance ID                     : uuid:2eb46376-d02e-4570-b706-e87bdf80f1db
Page Count                      : 68
Author                          : bduvall

EXIF Metadata provided by EXIF.tools