Netgear orporated 10400152 G54/N150 Wireless USB Micro Adaptor User Manual N150 Wireless Micro USB Adapter WNA1000M

Netgear Incorporated G54/N150 Wireless USB Micro Adaptor N150 Wireless Micro USB Adapter WNA1000M

User manual

Download: Netgear orporated 10400152 G54/N150 Wireless USB Micro Adaptor User Manual N150 Wireless Micro USB Adapter WNA1000M
Mirror Download [FCC.gov]Netgear orporated 10400152 G54/N150 Wireless USB Micro Adaptor User Manual N150 Wireless Micro USB Adapter WNA1000M
Document ID1428214
Application IDGeM0BPEeOSRRbiTo/FLAyg==
Document DescriptionUser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize114.57kB (1432170 bits)
Date Submitted2011-03-08 00:00:00
Date Available2011-03-08 00:00:00
Creation Date2011-01-27 12:27:02
Producing SoftwareAcrobat Distiller 9.2.0 (Windows)
Document Lastmod2011-03-03 16:40:36
Document TitleN150 Wireless Micro USB Adapter WNA1000M
Document CreatorFrameMaker 9.0
Document Author: NETGEAR, Inc.

N150 Wireless Micro USB
Adapter WNA1000M
User Manual
350 East Plumeria Drive
San Jose, CA 95134
USA
January 2011
202-10791-01
v1.0
N150 Wireless Micro USB Adapter WNA1000M
2 |
N150 Wireless Micro USB Adapter WNA1000M
© 2011 NETGEAR, Inc. All rights reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated
into any language in any form or by any means without the written permission of NETGEAR, Inc.
Technical Support
Thank you for choosing NETGEAR. To register your product, get the latest product updates, or get support
online, visit us at http://support.netgear.com.
Phone (US & Canada only): 1-888-NETGEAR
Phone (Other Countries): See Support information card.
Trademarks
NETGEAR, the NETGEAR logo, ReadyNAS, NeoTV, ProSafe, Smart Wizard, and Auto Uplink are trademarks or
registered trademarks of NETGEAR, Inc. Microsoft, Windows, Windows NT, and Vista are registered trademarks
of Microsoft Corporation. Other brand and product names are registered trademarks or trademarks of their
respective holders.
Statement of Conditions
To improve internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes
to the products described in this document without notice. NETGEAR does not assume any liability that may
occur due to the use, or application of, the product(s) or circuit layout(s) described herein.
Revision History
Publication Part Number
Version
Publish Date
Description
202-10791-01
v1.0
January 2011
Preliminary publication.
Table of Contents
Chapter 1 Getting Started
What You Need Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation with Custom Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
First, Install the WNA1000M Software. . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Then, Install Your Wireless-N USB Adapter . . . . . . . . . . . . . . . . . . . . . . 9
Using the Smart Wizard to Connect to a Wireless Network . . . . . . . . . 10
Wireless Network and Internet Connections . . . . . . . . . . . . . . . . . . . . . . . 11
WNA1000M Icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Smart Wizard Status Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Wireless-N USB Adapter LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Upgrading the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Removing the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Chapter 2 Network Connections and Wireless Security
Using the Smart Wizard After Installation . . . . . . . . . . . . . . . . . . . . . . . . .
Disabling the Windows Zero Configuration Utility . . . . . . . . . . . . . . . . .
Viewing Wireless Networks in Your Area . . . . . . . . . . . . . . . . . . . . . . . . .
Joining a Network without WPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using Push 'N' Connect to Join a Network . . . . . . . . . . . . . . . . . . . . . . . .
Creating Profiles to Connect to Networks . . . . . . . . . . . . . . . . . . . . . . . . .
Wireless Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting Up WPA2-PSK or WPA-PSK Wireless Security . . . . . . . . . . . .
Setting Up WEP Encryption Security. . . . . . . . . . . . . . . . . . . . . . . . . . .
Viewing Statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Viewing the About Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Advanced Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Working with Ad Hoc Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Creating an Ad Hoc Mode Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting a Computer-to-Computer (Ad Hoc) Network Connection. . . . .
16
16
17
18
19
20
21
21
22
23
23
24
25
25
27
Chapter 3 Wireless Network Performance
Optimizing Wireless Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optimizing Your Network Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Networking Technology and Connection Speed . . . . . . . . . . . . . . . . . .
Assessing Your Network Speed Requirements. . . . . . . . . . . . . . . . . . .
28
29
30
30
Chapter 4 Troubleshooting
Table of Contents | 4
N150 Wireless Micro USB Adapter WNA1000M
Frequently Asked Questions (FAQs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Ad Hoc Mode Is Not Working Correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Windows XP Occasional Connection Problems . . . . . . . . . . . . . . . . . . . . . 34
Appendix A
Technical Specifications and Factory Default Settings
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Appendix B
Related Documents
Appendix C
Notification of Compliance
Table of Contents | 5
N150 Wireless Micro USB Adapter WNA1000M
6 | Table of Contents
1.
Getting Started
This chapter describes how to install your wireless-N USB adapter with custom setup and how to
connect to a wireless network. For help with express installation, see the N150 Wireless Micro
USB Adapter WNA1000M Installation Guide.
What You Need Before You Begin
Make sure your computer meets the system requirements. You should also know the name of
the wireless network you want to join and its wireless security settings (if used).
•
PC with a Pentium 300 MHz or higher compatible processor with a USB 2.0 or 1.1 port.
The maximum speed of a USB v2.0 port is 480 Mbps. If your computer has a USB v1.1
port, the wireless-N USB adapter is limited to the port’s maximum speed of 14 Mbps.
•
A CD drive.
•
5 Mbytes of free hard disk space.
•
Vista, Windows XP Home, or Windows XP Professional. Some versions of Windows ask
for the original Windows operating system installation files to complete the installation of
the WNA1000M software.
Note: Windows XP users must install SP2 or install the KB822603 hot fix
(update), which fixes the USB 2.0 host controller driver. Go to the
following link to install the hot fix:
http://www.microsoft.com/downloads/details.aspx?displaylang=
en&FamilyID=733dd867-56a0-4956-b7fe-e85b688b7f86
Chapter 1: Getting Started
N150 Wireless Micro USB Adapter WNA1000M
Installation with Custom Setup
Note: For help with Express installation, see the N150 Wireless Micro USB
Adapter WNA1000M Installation Guide.
First, Install the WNA1000M Software
1. Insert the Resource CD in your computer’s CD drive. If the CD main screen does not
display, browse the files on the CD and double-click Autorun.exe.
2. Click Setup. The Software Update Check screen displays.
3. If you are connected to the Internet, click Check for Updates. If not, click Install from CD.
4. Accept the license agreement. Then select Custom and click Next on the Setup Type
screen.
8 | Chapter 1: Getting Started
N150 Wireless Micro USB Adapter WNA1000M
5. When prompted, browse to select the destination folder for your wireless adapter software,
and click Next.
6. Select one of the following methods to configure and manage your wireless network:
• Smart Wizard. Manage your wireless networks with the NETGEAR Smart Wizard.
•
Automatically. Let the Smart Wizard configure the settings for your wireless-N
USB adapter.
Manual. Specify the settings for your wireless-N USB adapter in the Settings
screen.
Windows Utility. Connect to and manage your wireless networks using only the
Windows configuration utility.
Then, Install Your Wireless-N USB Adapter
You are prompted to insert your adapter:
1. Insert the adapter into a USB port on your computer.
Note: For best results, put the wireless adapter at least 4 feet (1 meter)
away from your router.
Chapter 1: Getting Started
N150 Wireless Micro USB Adapter WNA1000M
2. Click Next. The Smart Wizard software detects the adapter.
3. Follow the onscreen prompts to install the driver and complete the installation.
How you connect to a network depends on what you selected during custom installation.
•
If you installed the Smart Wizard with automatic configuration, see the following
section, Using the Smart Wizard to Connect to a Wireless Network.”
•
If you installed the Smart Wizard with manual configuration, the Settings tab displays.
See Viewing Wireless Networks in Your Area on page 17.
•
To use a Windows utility, see your Windows documentation or the NETGEAR
application note at
http://documentation.netgear.com/reference/enu/winzerocfg/index.htm.
Using the Smart Wizard to Connect to a Wireless Network
After the software is installed, you are prompted to connect to a wireless network.
1. One of the following screens displays:
WPS network
No WPS networks
•
WPS network: A network in your area supports Push 'N' Connect (also called WPS).
Click Next, and follow the prompts to push the WPS button on your adapter and
connect without entering a password.
•
No WPS networks: Select a wireless network from the list and click Next. To connect
to a secure network, you must enter its passphrase or network key.
10 | Chapter 1: Getting Started
N150 Wireless Micro USB Adapter WNA1000M
2. The adapter connects to the network, which can take a minute or two. Your settings are
saved in a profile, which you can name:
3. Click Finish, and the Smart Wizard Settings screen displays.
The
icon appears in the system tray and on the desktop so you can open the Smart
Wizard to make changes or connect to a different wireless network.
Wireless Network and Internet Connections
The Smart Wizard and wireless-N USB adapter provide several ways to check the status of
your connection to a wireless network and to the Internet:
•
WNA1000M icon. After you install the WNA1000M software, the
icon appears on the
desktop and in the right on the Windows task bar. It is color coded to show the status of
the connection.
•
Smart Wizard status bar. Clicking on the system tray icon opens the Smart Wizard. The
status bar at the bottom of the screen shows details about your wireless and Internet
connection. See Smart Wizard Status Bar.
•
Adapter LED status lights. The LED on the wireless-N USB adapter shows the network
connection. Solid indicates a connection. The LED blinks when the wireless-N USB
adapter is looking for a network association and when it is sending or receiving data. See
Wireless-N USB Adapter LED on page 14.
Chapter 1: Getting Started
11
N150 Wireless Micro USB Adapter WNA1000M
WNA1000M Icon
This icon is on the desktop and in the Windows system tray. The system tray is on one end of
the task bar in the Microsoft Windows desktop. The icon color shows the wireless connection.
Color
Meaning
Recommended Action
Red
The wireless-N USB adapter is not Check your configuration, or try moving to a location
connected to a wireless network. where the wireless signal quality is better.
Yellow
The wireless-N USB adapter has a Move to a better location, such as closer to the wireless
weak wireless connection.
access point. Also, look for interference such as from a
2.4 GHz cordless phone or large metal surface.
Green
The wireless connection is good.
No action is required
Smart Wizard Status Bar
For more information, you can view the Smart Wizard status bar. Click the
icon to open
the Smart Wizard status bar. The Smart Wizard Settings tab displays. The status bar is
located at the bottom of the Settings tab.
Security
Channel
Throughput
Wireless
network
Signal
strength
Join a Network
Connection status
The following table describes how to interpret the Smart Wizard status bar.
Understanding the Status Bar
Wireless network
Identifies which wireless network you have joined.
Security
• A closed lock indicates that security is enabled.
• An open lock indicates an open network without wireless security.
Channel
The wireless channel used by the network. If many wireless networks in
your area use the same channel, they can interfere with one another.
Throughput
• To optimize wireless throughput, connect to a network with a
•
high-speed router or access point and a high-speed Internet
connection.See Chapter 3.
If your computer has a USB v1.1 port, the wireless-N USB adapter is
limited to that port’s maximum speed, which is 14 Mbps.
12 | Chapter 1: Getting Started
N150 Wireless Micro USB Adapter WNA1000M
Understanding the Status Bar (Continued)
Signal strength
More dots indicates a stronger signal. Usually, you experience higher
throughput when the signal is strongest.
Join a Network
Click Join a Network to open the Connection Wizard.
Connection
status
The status of your network connection.
• Connected to Internet. The wireless Internet connection is OK.
• Connected to Router. The wireless connection to the router is OK, but
the router is not connected to the Internet.
169.254.x.x or ___.___.___.___. The wireless connection to the router is
OK, but there is a problem with the router. See the online help or
Chapter 4.
The connection status is useful in isolating a problem. For example, if you are connected to a
router, but not to the Internet, check the router’s Internet connection.
Internet Connection and Smart Wizard Configuration
You can turn off the Internet notification feature on the Status bar. Right-click the system tray
icon to view the Enable Internet Connected Notification check mark. If you clear the
checkmark, only the IP address is shown.
Windows XP
Windows 7 and Vista
In Microsoft Windows 7 and Vista, there is one more option. If you clear the Enable
NETGEAR Smart Wizard check mark, the NETGEAR Smart Wizard is disabled, and you
must set up the wireless adapter with auto-configuration.
Chapter 1: Getting Started
13
N150 Wireless Micro USB Adapter WNA1000M
Wireless-N USB Adapter LED
The LED shows the status of the wireless link as explained in the following table.
Wireless-N USB Adapter
LED
Meaning
Off
• The wireless-N USB adapter in not plugged in to the USB port.
• The wireless-N USB adapter is in power save mode (default from
power up or reset).
Slow
blinking
• Alternating amber and blue. The wireless-N USB adapter is
•
scanning for a network.
Blue. The wireless-N USB adapter is connecting to a network at
2.4 GHz.
Blinking
The wireless-N USB adapter is connected to a wireless network, and
is sending or receiving data.
Solid
The wireless-N USB adapter is connected to a wireless network, but
it is not sending or receiving data.
Upgrading the Software
Upgrades might be available at the NETGEAR website.
To check for an update and install it:
1. Open the Smart Wizard and click the About tab:
2. Click the Software Update Check button.
14 | Chapter 1: Getting Started
N150 Wireless Micro USB Adapter WNA1000M
The Smart Wizard goes to the NETGEAR website and checks for newer software. If there
is a newer version of firmware, this screen displays:
3. Click OK. When the file has been downloaded, a message like the following displays:
4. Click Yes. Follow the installer instructions, and if prompted, restart your computer.
Removing the Software
You can remove the wireless adapter software through the Windows Program List or the
Windows Control Panel.
•
Windows Program List: Select Windows Start > Micro USB Adapter program group.
Click Uninstall and follow the screen prompts.
•
Control Panel: How you do this depends on your Windows operating system:
Windows 7: Select Windows Start >Control Panel > Programs and Features >
Micro USB Adapter. Click Uninstall and follow the screen prompts.
Windows Vista: Select Windows Start >Control Panel > Programs and Features >
Micro USB Adapter. Click Uninstall/Change from the top menu and follow the
screen prompts.
Windows XP: Select Windows Start > Control Panel > Add or Remove Program,
and then select Micro USB Adapter.
Chapter 1: Getting Started
15
2.
Network Connections and Wireless
Security
This chapter explains how to use your wireless-N USB adapter to connect to wireless networks
and how to set up wireless security for the wireless-N USB adapter so that it matches the
wireless security settings for your network.
Using the Smart Wizard After Installation
When you installed the software from the Resource CD, the
icon appeared on your
desktop and in the Windows system tray. The Windows system tray is located on the
Windows taskbar. You can either double-click this icon on the desktop or click it in the system
tray at any time, to use the Smart Wizard. This software automatically restarts when you
reboot your computer.
The Smart Wizard provides a complete and easy-to-use set of tools to:
•
View details about wireless networks in your area.
•
Choose the network that you want to use.
•
Configure wireless settings for your wireless-N USB adapter.
•
Save your wireless network settings in profiles.
•
Remove or reinstall the wireless adapter software.
Disabling the Windows Zero Configuration Utility
If you chose the Windows XP or Windows Vista Zero Configuration utility during installation,
and now you want to use the Smart Wizard that is installed on your PC, you must disable the
Windows utility. If you are working with the Vista configuration utility, see the NETGEAR
online application note at:
http://documentation.netgear.com/reference/enu/winzerocfg/index.htm
To disable the Windows Zero Configuration utility:
1. Attach the wireless adapter to a USB port for your computer.
2. In Windows, select Start > Network Connections.
Chapter 2: Network Connections and Wireless Security
16
N150 Wireless Micro USB Adapter WNA1000M
3. Select Wireless Network Connection, right-click, and then select Properties.
4. Click the Wireless Networks tab. Then clear the Use Windows to configure my wireless
settings check box.
Viewing Wireless Networks in Your Area
You can use the Networks tab to view all available wireless networks in your area. You can
also scan to search for wireless networks and refresh the tab.
To view wireless networks:
1. Use the
icon to open the Smart Wizard.
2. Click the Networks tab to display the following screen:
You can click a column
heading to sort.
If many networks use
the same channel they
can interfere with each
other. (G) indicates a
2.4 GHz network.
The status bar shows
your network connection
and Internet connection.
The screen shows the following information for each network scanned:
•
Network Name (SSID). The name of the wireless network. As a security measure, some
wireless access points do not broadcast the network name. In such cases, the Network
Name (SSID) field is blank even though the rest of the information is displayed.
Chapter 2: Network Connections and Wireless Security
17
N150 Wireless Micro USB Adapter WNA1000M
•
Channel. The channel determines which operating frequency is used. In this column
(G) indicates a 2.4 GHz network.
•
N. The access point supports wireless N mode.
•
WPS. The access point supports WPS.
•
Security. Identifies whether the wireless network uses security settings such as
WPA2-PSK, WPA-PSK, or WEP.
•
Signal. Identifies the signal strength of the communications.
•
MAC Address. Identifies the hardware address (MAC address) of the wireless device
broadcasting this information.
•
Mode. Identifies the type of wireless network — Access Point (Infrastructure) or
Computer-to-Computer (Ad Hoc)
The buttons located at the bottom of the Networks tab are:
•
Help. Display online help.
•
Join a Network. View networks and join a network. See Joining a Network without WPS
on page 18.
•
Connect. Connect to the network that you selected.
•
Scan. Check for wireless networks. Clicking Scan refreshes the screen.
•
Close. Close the window of the Wizard.
Joining a Network without WPS
1. Use the
icon to open the Smart Wizard. On the status bar at the bottom of the
screen, click Join a Network.
If there is a WPS network in your area, the Smart Wizard displays the WPS screen. To
bypass WPS, select No to avoid connecting, and then click Next.
2. Select a network from the drop-down list. If
you select a hidden network, you must enter
the SSID. Click Next.
3. Follow the wizard steps to specify the
wireless security if used, and to create a
profile.
4. Review you settings, and click Finish.
The status bar shows the status of your
wireless connection.
18 | Chapter 2: Network Connections and Wireless Security
hidden network
N150 Wireless Micro USB Adapter WNA1000M
Using Push 'N' Connect to Join a Network
Push 'N' Connect (also called WPS) lets you join a secure wireless network by pushing a
button instead of entering a passphrase or network key. Your wireless-N USB adapter works
with WPS, but only if the wireless network you want to join also supports WPS. An access
point or router that supports WPS has a WPS symbol
on it.
To join a network using WPS:
icon to open the Smart Wizard. On the status bar at the bottom of the
1. Use the
screen, click Join a Network.
The Smart Wizard detects a WPS
network.
2. Select the Yes, I will connect using Push
'N' Connect radio button, and then click
Next.
3. Either push the WPS button on the
wireless-N USB adapter or click the
onscreen WPS button. Click Next.
4. On the access point or router for the
network you want to join, use its Smart
Wizard or WPS configuration utility, and
push its WPS button as directed.
• The access point or router adds the
wireless-N USB adapter to the
network.
•
The wireless-N USB adapter Smart
Wizard status bar shows the status of
your wireless connection.
5. Click Close to exit the Smart Wizard.
6. Close the Smart Wizard or configuration utility for the access point or router.
Chapter 2: Network Connections and Wireless Security
19
N150 Wireless Micro USB Adapter WNA1000M
Creating Profiles to Connect to Networks
The Smart Wizard can create a profile for each wireless network that you join when using
your wireless-N USB adapter. If you connect to different networks, name the profiles and
save them to easily connect the next time you join the same network. Advanced users can
also set up profiles for Ad Hoc mode connections for peer-to-peer networking. See Working
with Ad Hoc Mode on page 25.
There are two special profile names: Default and Profile.
•
Default. This profile scans for any available network. You cannot change this profile
name.
•
Profile. If you do not enter a name in the Profile Name field when you connect to a
network, the name Profile is used to save your settings. If you do this more than once,
you are asked if you want to replace the previous settings stored in Profile.
To set up a profile to connect to a network:
1. Use the
icon to open the Smart Wizard. The Settings tab displays:
2. In the Profiles field, type the name of the profile.
3. In the Network Name (SSID) field, select a network or enter the SSID.
Note: You cannot connect wirelessly unless the network SSID matches
exactly the SSID used by the wireless network.
4. Make sure that the Access Point (Infrastructure) radio button is selected. This setting
allows you to connect to a wireless router or access point.
5. Click Save Profile.
6. Click Apply, then click Close to exit, or click Cancel to return to the previous settings.
7. To make sure your network connection is working, use a browser to connect to the Internet.
The status bar in the Smart Wizard shows the current connection status.
20 | Chapter 2: Network Connections and Wireless Security
N150 Wireless Micro USB Adapter WNA1000M
Wireless Security
Many networks use wireless security. The first time you join a network that uses wireless
security, you must either know its security settings, or use Push 'N' Connect (WPS) for a
WPS-compatible wireless network. The main types of wireless security are:
•
Wi-Fi Protected Access 2 Pre-Shared Key (WPA2-PSK)
•
Wi-Fi Protected Access Pre-Shared Key (WPA-PSK)
•
Wired Equivalent Privacy (WEP)
For more information about wireless security, see the wireless reference document at
http://documentation.netgear.com/reference/enu/wireless/index.htm.
Setting Up WPA2-PSK or WPA-PSK Wireless Security
1. Use the
icon to open the Smart Wizard. The Settings tab displays:
2. In the Profile field, select the profile, or type in a profile name.
3. In the Network Name (SSID) field select the network, or enter the SSID.
4. In the Security section, select the WPA2 or WPA setting for the wireless network that you
want to join and enter the passphrase.
5. Click the Save Profile button. All the configuration settings are saved in this profile.
6. Click Apply, and then click Close to exit the Smart Wizard.
Chapter 2: Network Connections and Wireless Security
21
N150 Wireless Micro USB Adapter WNA1000M
Setting Up WEP Encryption Security
1. Use the
icon to open the Smart Wizard. The Settings tab displays:
2. In the Profile field, select the profile or type in a profile name.
3. In the Network Name (SSID) field, select the network, or enter the SSID.
4. In the Security section, select WEP and then select the WEP encryption strength:
• 64-bit WEP data encryption
•
128-bit WEP data encryption
5. Select Create with Passphrase, and enter the passphrase so that the Smart Wizard will
generate the WEP keys. The characters are case-sensitive. Be sure to use the same
passphrase for all the wireless devices in the network.
If the wireless network that you want to join does not support the passphrase method, you
must enter the keys so that they match the wireless network exactly.
6. Click the Save Profile button.
7. Click Apply and then click Close to exit the configuration utility.
22 | Chapter 2: Network Connections and Wireless Security
N150 Wireless Micro USB Adapter WNA1000M
Viewing Statistics
The Statistics tab provides real time
and historical trend information about
the data traffic and performance of
your wireless adapter.
•
Transmit/Receive Performance
(%). A real-time graph identifies
the total, receive, and transmit
utilization as a percentage the
total possible.
•
Transmit, Receive, and Total
(TxRx). Radio buttons let you
select whether to display the
transmit performance, the receive
performance, or both in the same graph.
•
Transmit Statistics. Identifies transmit megabits per second (Mbps), transmit packets
per second (Tx Packets/s), total transmitted packets, and transmit errors.
•
Receive Statistics. Identifies receive megabits per second (Mbps), receive packets per
second (Rx Packets/s), total received packets, and reception errors.
Viewing the About Tab
The About tab displays the current version information and allows you to check for software
updates (See Upgrading the Software on page 14).
The following information is displayed in the About tab:
•
Region. This is the region setting for the wireless adapter. The approved channels for the
region are automatically scanned. Governments regulate the channels used for wireless
transmission. Operating the wireless adapter in a different region might violate local laws.
Chapter 2: Network Connections and Wireless Security
23
N150 Wireless Micro USB Adapter WNA1000M
•
Driver Version and Driver Date: The wireless adapter driver version and release date.
•
MAC Address. The Media Access Control (MAC) address of the adapter. This is a
unique 48-bit hardware address. Some wireless networks restrict access based on a list
of known MAC addresses. To connect to such a network, you must first provide the MAC
address shown here to the network administrator.
•
IP Address. The IP address assigned to this adapter.
•
Smart Wireless Utility. The version and release date of the Smart Wizard.
Note: The Get Info button displays technical messages that can be used
for troubleshooting.
Advanced Settings
You can use the Advanced Settings screen to configure the preamble (GHz) that the adapter
uses. The available settings are Auto and 2.4 GHz. The 2.4GHz range is commonly used by
cordless telephones.
Note: The default settings for the Fragmentation Threshold field and
RTS/CTS Threshold field usually work fine. Do not change them
unless you have a specific reason to do so.
By changing the preamble setting, you have the option to connect to the following types of
wireless networks.
•
2.4 GHz only. Connect only to 2.4GHz access points, up to 150 Mbps.
•
2.4 GHz. Connect to 802.11b/g access points, up to 54 Mbps.
To change the preamble (GHz) setting:
1. On the Settings tab, click the Advanced
Settings button.
Note: For Windows Vista computers, you
must have administrator rights. Otherwise,
this option is not available for selection.
2. In the Advanced section of the screen, adjust
the settings as needed.
Changing the setting in the Preamble field
affects which options are available in the
Wireless Mode section of this screen. You
24 | Chapter 2: Network Connections and Wireless Security
N150 Wireless Micro USB Adapter WNA1000M
can change the preamble for better throughput if you experience interference, such as
from a cordless telephone. Many cordless phones use 2.4 GHz.
•
Auto. Up to 150 Mbps.
•
2.4 GHz. Use a 2.4 GHz preamble.
•
Long.
3. Click OK.
Working with Ad Hoc Mode
Ad Hoc Mode is an advanced feature that allows you to create a wireless network between
two computers without using a router or access point. For example, this mode is used when
two Windows computers are configured with file and print sharing enabled and you want to
exchange files directly between them.
Note: Ad Hoc mode does not work using DHCP settings. Ad Hoc mode
requires either static IP addresses (such as 192.168.0.1) or the IPX
protocol. For help setting up static IP addresses, see the PC
Networking Tutorial on the Resource CD.
For more information about wireless network modes, see the wireless reference document
at: http://documentation.netgear.com/reference/enu/wireless/index.htm.
Creating an Ad Hoc Mode Profile
1. Use the
icon to open the Smart Wizard. The Settings tab displays:
2. Enter the network settings.
a. Select Computer-to-Computer (Ad Hoc) for the network type.
b. Select or enter the network name (SSID) for the Ad Hoc network.
Chapter 2: Network Connections and Wireless Security
25
N150 Wireless Micro USB Adapter WNA1000M
c. In the Profile field, type the name of the profile.
d. Click Apply.
3. Save your settings in a profile.
a. Click Save Profile, and all the configuration settings are saved in this profile.
b. Click Apply, then click Close to exit the Smart Wizard, or click Cancel to return to
the previous settings.
4. Configure the computer network settings.
a. Configure each computer with either a static IP address or with the IPX protocol.
b. Restart the computers.
5. Verify wireless connectivity between your peer devices with the ping program:
a. On the Windows taskbar, select Start > Run.
b. Assuming the target PC is configured with 192.168.0.1 as its IP address, type:
ping -t 192.168.0.1
and then click OK.
c. A continuous ping will be sent to the device with the 192.168.0.1 static IP address.
The ping response should change to Reply.
At this point the connection is established.
Note: If you cannot connect, see Removing the Software on page 15. For
problems accessing network resources, the Windows client and rile
and print sharing software might not be installed or configured
correctly on your computers. See the link to Internet Networking and
TCP/IP Addressing: in Appendix B.
26 | Chapter 2: Network Connections and Wireless Security
N150 Wireless Micro USB Adapter WNA1000M
Starting a Computer-to-Computer (Ad Hoc) Network
Connection
1. On the Settings tab of the Smart Wizard, select or type the network name (SSID).
2. Select the Computer-to-Computer (Ad Hoc) network type.
Note: For Windows Vista computers, you must have administrator rights.
Otherwise, this option is not available for selection.
3. Click Initiate Ad Hoc. The Ad Hoc Setting screen displays:
4. In the Start Ad Hoc drop-down list, select the wireless standard (802.11a, 802.11b, or
802.11g) for your Ad Hoc computer-to-computer network.
5. In the Channel field, Automatic should work. If there is interference from a nearby wireless
device, select a different channel. You can use the Networks tab to view channels in use in
your area. The channel number differs depending on the country. The connection speed
automatically defaults to the highest speed.
6. Click OK.
Chapter 2: Network Connections and Wireless Security
27
3.
Wireless Network Performance
This chapter explains how to maximize the performance of your wireless-N USB adapter within
your network.
Optimizing Wireless Performance
The position of your wireless-N USB adapter and the local environment can affect its wireless
performance.
•
Use the plastic cradle that came in the package with your adapter. This lets you place the
adapter in a better position for wireless communication.
•
Make sure you do not have interference from other wireless equipment, especially those
in the 2400–2500 MHz frequency band. Common sources of interference are:
Other computers and fax machines (no closer than 1 foot)
Copying machines, elevators, and cell phones (no closer than 6 feet)
Microwave ovens (no closer than 10 feet)
How the wireless router or access point is set up also affects wireless communication. For
best performance, try the following:
•
For better throughput and a higher link rate, set your router or access point wireless mode
to Up to 150 Mbps, or HT 20/40 Mbps.
•
For a faster connection, set the security for the router as WPA2 or WPA + WPA2 mixed
wireless security instead of WPA (TKIP). Wi-Fi regulations allow only the adapter to
connect at up to 54 Mbps when WPA (TKIP) security mode is set on the router.
•
Avoid using the same wireless channel as your neighbor. To find out which channels are
in use in your area, select the Smart Wizard Networks tab. It lists wireless networks in
your area including the channel used by each.
Chapter 3: Wireless Network Performance
28
N150 Wireless Micro USB Adapter WNA1000M
Optimizing Your Network Bandwidth
The speed of network connections depends on the type of equipment that you use. Try to
use high-speed technologies for network connections with the heaviest traffic to avoid
lower-speed bottlenecks. The following illustration shows a home network that includes many
different connection speeds.
Figure 1. Home Network
In this network, the two PCs with gigabit (1000 Mbps) Ethernet adapters have a gigabit
connection through the router to the storage server. With a high-speed router this connection
allows for extremely fast backups or quick access to large files on the server. The PC
connected through a pair of Powerline HD adapters is limited to the 200 Mbps speed of the
Powerline HD connection. Although any of the links in this example would work for high-traffic
applications such as streaming HD video, the use of older devices such as 10 Mbps Ethernet
or 802.11b wireless would create a bottleneck.
In planning your network, think about which tasks will have the heaviest traffic flow between
them. Examples are:
•
A media center in one room streaming high-definition video from a server in another room
•
A storage device that is used for backing up your computers
Chapter 3: Wireless Network Performance
29
N150 Wireless Micro USB Adapter WNA1000M
Networking Technology and Connection Speed
Common connection types and their speed and security considerations are:
•
Broadband Internet
Your Internet connection speed depends on your modem type, such as ADSL or cable
modem, as well as the speed of the sites to which you connect, and general Internet
traffic. ADSL and cable modem connections have a lower data rate to the Internet
(upstream) than from the Internet (downstream). Keep in mind that when you connect to
someone else who also has an ADSL or cable modem connection, the data rate between
your sites is limited by each side’s upstream data rate. A typical residential ADSL or cable
modem connection provides a downstream throughput of about 1 to 3 megabits per
second (Mbps). Newer technologies such as ADSL2+ and Fiber to the Home (FTTH) l
increase the connection speed to tens of Mbps.
•
Wireless
A high-speed wireless router can provide a wireless data throughput of up to 150 Mbps
with excellent range and coverage. WPA and WPA2 wireless security are extremely
strong.
To get the best performance, connect to networks that use newer routers. Your
wireless-N USB adapter will work with older 802.11b and 802.11g routers, but the use of
these older wireless technologies in your network can result in lower throughput overall.
In addition, many older wireless products do not support the latest security protocols,
WPA and WPA2.
•
Powerline
You can use Powerline connections for rooms that are upstairs or too far from your router
for a good wireless connection. NETGEAR’s Powerline HD products deliver up to 200
Mbps to any outlet. Data transmissions are encrypted for security, and you can set up a
network password to prevent neighbors from connecting.
•
Wired Ethernet
Wired Ethernet remains a good choice for speed, economy, and security. Gigabit Ethernet
can extend up to 100 meters.
Note: Actual data throughput will vary. Network conditions and
environmental factors, including volume of network traffic, building
materials and construction, and network overhead, can lower actual
data throughput rate.
Assessing Your Network Speed Requirements
Because your Internet connection is likely to operate at a much lower speed than your local
network, faster local networking technologies might not improve your Internet experience.
However, many emerging home applications require high data rates. For example:
30 | Chapter 3: Wireless Network Performance
N150 Wireless Micro USB Adapter WNA1000M
•
Streaming HD video requires 10 to 30 Mbps per stream. Because latency and packet loss
can disrupt your video, plan to provide at least twice the capacity you need.
•
Streaming MP3 audio requires less than 1 Mbps per stream and does not strain most
modern networks. Like video, however, streaming audio is also sensitive to latency and
packet loss, so a congested network or a noisy link can cause problems.
•
Backing up computers over the network has become popular due to the availability of
inexpensive mass storage. The following table shows the time to transfer 1 gigabyte (1
GB) of data using various networking technologies.
Table 1. Theoretical Transfer Time for 1 Gigabyte
Network Connection
Theoretical Raw Transfer Time
Gigabit Wired Ethernet
8 seconds
RangeMax Dual Band Wireless-N
26 seconds
Powerline HD
40 seconds
100 Mbps Wired Ethernet
80 seconds
802.11g wireless
150 seconds
802.11b wireless
700 seconds
10 Mbps Wired Ethernet
800 seconds
Cable Modem (3 Mbps)
2700 seconds
Analog Modem (56 kbps)
144,000 seconds (40 hours)
Chapter 3: Wireless Network Performance
31
4.
Troubleshooting
This chapter provides information about troubleshooting your wireless-N USB adapter. You can
also refer to the Knowledge Base on the NETGEAR website at http://support.netgear.com.
Frequently Asked Questions (FAQs)
The wireless-N USB adapter LED is not lit.
The wireless-N USB adapter is not inserted securely in the USB port (or USB cable if used)
or the WNA1000M software is not installed.
•
Remove and reinsert the wireless-N USB adapter.
•
Check the Windows device manager to see if the wireless-N USB adapter is recognized
and enabled. Re-install the WNA1000M software, if necessary.
•
Insert the wireless-N USB adapter in a different USB port on your computer if one is
available.
I cannot connect to a wireless network.
•
Make sure that your wireless-N USB adapter is inserted securely into the USB port on
your computer or the USB cable if you are using it. The wireless-N USB adapter LED
should light up or blink (see Wireless-N USB Adapter LED on page 14 for details).
•
Click the
icon to open the Smart Wizard and then click the Networks tab to view the
networks in your area. Make sure the signal strength is strong and that you have selected
the correct wireless network.
•
If the network uses wireless security, you need to either know the wireless security
settings or use Push 'N' Connect if the network supports WPS. Some networks also
restrict use to only computers or wireless devices with known MAC addresses. If that is
the case, use the Smart Wizard About tab to find the MAC address for your wireless-N
USB adapter and provide it to the network administrator.
Chapter 4: Troubleshooting
32
N150 Wireless Micro USB Adapter WNA1000M
When I connect to the network I cannot access the Internet.
Click
to open the Smart Wizard, and then check the connection status in the status bar at
the bottom of the screen.
Connection status
Here is a list of connection statuses and their meanings:
•
Connected to Internet: The wireless Internet connection is OK.
•
Connected to Router: The wireless connection to the router is OK, but the router is not
connected to the Internet.
•
169.254.x.x or ___.___.___.___: The wireless connection to the router is OK, but there is
a problem with the router.
If the router’s Internet connection is not working, restart the modem, router, and computer.
When I connect to the network I cannot access shared resources such as printers.
•
Check to make sure the router or access point is physically connected to the Ethernet
network.
•
Make sure that the IP addresses and the Windows networking settings are configured
correctly. See the link to Internet Networking and TCP/IP Addressing: in Appendix B.
How can I improve the speed of my wireless connection?
You can use the USB cable and adapter that came in the package to position the wireless-N
USB adapter for better wireless communication.
The connection speed can vary depending on the type of USB port on your computer, the
capacity of the router or access point for the wireless network, and the type of Internet
connection. You can view the throughput in the status bar at the bottom of the Smart Wizard
screen.
•
If the throughput is 54 Mbps you could be connected to an 802.11g network, or the
wireless-N network could be set with WPA (TKIP) security.
Wi-Fi regulations allow the wireless-N USB adapter to connect only at up to 54 Mbps
when WPA (TKIP) security mode is set on the router. For a faster connection, set the
security for the router as WPA2 or WPA + WPA2 mixed wireless security. Then the
wireless adapter can connect in 802.11n mode.
•
If you do not have a USB 2.0 port on your computer, the throughput is limited to the 14
Mbps of the older USB 1.1 standard.
•
For more information about connection speeds, see Optimizing Wireless Performance on
page 28.
Chapter 4: Troubleshooting
33
N150 Wireless Micro USB Adapter WNA1000M
The Smart Wizard keeps asking me to save settings.
If you change the settings, the Smart Wizard offers you the chance to save the changes. To
avoid this prompt, click Apply before you close the Smart Wizard.
Two WNA1000M icons are in the Windows system tray.
You have an older software version installed on your system and it needs to be removed.
See Removing the Software on page 15.
How can I view the IP address for the wireless-N USB adapter?
Click the
icon to open the Smart Wizard. Then click the About tab to view the IP address.
No IP address is assigned to the wireless-N USB adapter.
This can occur if you upgraded your wireless-N USB adapter software and did not reboot
your computer.
•
Either restart your computer, or connect to a different access point.
•
It does not usually help to shut down the Smart Wizard or disable or enable the
wireless-N USB adapter.
Ad Hoc Mode Is Not Working Correctly
You must click the Initiate Ad Hoc button before you click Apply.
Note: Be sure that all computers in your Ad Hoc network are configured
with static IP addresses in the same subnet.
To start an Ad Hoc network:
1. Fill in the Network Name (SSID) field.
2. Select the Computer-to-Computer (Ad Hoc) network type.
3. Click Initiate Ad Hoc.
4. Accept the default settings, or make your changes and click OK.
Click Apply.
Windows XP Occasional Connection Problems
Windows XP users who apply Windows XP Hotfix (SP2) Q815485 from the Windows XP
Update Service might not be able to connect to the Internet, might have dropped wireless
34 | Chapter 4: Troubleshooting
N150 Wireless Micro USB Adapter WNA1000M
connections, or both when using the Micro USB Adapter. You can delete this Hotfix from the
Add or Remove Programs utility in the Control Panel.
To delete Windows XP Hotfix (SP2) Q815485:
1. Select Start > Control Panel > Add/Remove Programs.
2. Select Windows XP Hotfix (SP2) Q815485, and then click Remove.
• You might receive an error message that states that some program on the computer
might not work correctly if the update is removed.
•
You can ignore this error message, and then click Yes to remove the update.
3. Restart your computer, and rerun the Smart Display Setup Wizard.
This should solve your connection issue. You can restore this hotfix by following this link:
http://microsoft.com/downloads/details.aspx?FamilyId=
009D8425-CE2B-47A4-ABEC-274845DC9E91&displaylang=en
Chapter 4: Troubleshooting
35
A.
Technical Specifications and Factory
Default Settings
Technical Specifications
The following table provides technical specifications for the wireless-N USB adapter.
Feature
Description
Antenna
2 integrated internal wireless antennas
Standards
802.11n, 802.11g, or 802.11b
Radio Data Rate
1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54, 72, and 150 Mbps
(Auto Rate Sensing)
Frequency
2.4 GHz to 2.5 GHz CCK and OFDM Modulation);
Power
5V Bus powered
Emissions
FCC, CE
Bus interface
USB 2.0
Provided drivers
Microsoft Windows 7, Vista, Windows XP
Operating Environment
Operating temperature: 0 to 40 C
Encryption
40-bit (also called 64-bit) and 128-bit WEP data encryption, and
WPA-PSK
Warranty
Limited 1-year warranty
Appendix A: Technical Specifications and Factory Default Settings
36
N150 Wireless Micro USB Adapter WNA1000M
Factory Default Settings
The following table lists the default settings of your wireless-N USB adapter.
Default Settings
Smart Wizard
Enabled
Wireless
Wireless communication
Enabled
Wireless Network Name (SSID)
Any (will connect to the first wireless network that responds.
Security
Disabled
Network type
Infrastructure
Transmission speed
Auto1
Country/Region
United States (varies by region)
Operating mode
802.11n, 802.11g, 802.11b
Data rate
Up to 150 Mbps
1 Maximum wireless signal rate (IEEE Standard 802.11). Actual throughput will vary. Network conditions and
environmental factors, including volume of network traffic, building materials and construction, and network overhead,
lower actual data throughput rate
Appendix A: Technical Specifications and Factory Default Settings
37
B.
Related Documents
This appendix provides links to reference documents you can use to gain a more complete
understanding of the technologies used in your NETGEAR product.
Document
Link
Windows XP and Vista
Wireless Configuration
Utilities Application Note
http://documentation.netgear.com/reference/enu/winzerocfg/index.htm
Internet Networking and
TCP/IP Addressing:
http://documentation.netgear.com/reference/enu/tcpip/index.htm
Wireless Communications:
http://documentation.netgear.com/reference/enu/wireless/index.htm
Preparing a Computer for
Network Access:
http://documentation.netgear.com/reference/enu/wsdhcp/index.htm
Virtual Private Networking
(VPN):
http://documentation.netgear.com/reference/enu/vpn/index.htm
Glossary:
http://documentation.netgear.com/reference/enu/glossary/index.htm
Appendix B: Related Documents
38
N150 Wireless Micro USB Adapter WNA1000M
Appendix B: Related Documents
39
C.
Notification of Compliance
Regulatory Compliance Information
This section includes user requirements for operating this product in accordance with National laws for usage of radio
spectrum and operation of radio devices. Failure of the end-user to comply with the applicable requirements may
result in unlawful operation and adverse action against the end-user by the applicable National regulatory authority.
Note: This product’s firmware limits operation to only the channels allowed in a particular Region or Country.
Therefore, all options described in this user's guide may not be available in your version of the product.
FCC Requirements for Operation in the United States
FCC Information to User
This product does not contain any user serviceable components and is to be used with approved antennas only.
Any product changes or modifications will invalidate all applicable regulatory certifications and approvals
FCC Declaration of Conformity
We, NETGEAR, Inc., 350 East Plumeria Drive, San Jose, CA 95134, declare under our sole responsibility that the
N150 Wireless Micro USB Adapter WNA1000M complies with Part 15 Subpart B of FCC CFR47 Rules. Operation
is subject to the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received, including interference that may cause undesired operation.
FCC Radio Frequency Interference Warnings & Instructions
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following methods:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an electrical outlet on a circuit different from that which the radio receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
• Any changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate this equipment.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Appendix C. Notification of Compliance
40
New Template User Manual
FCC Radiation Exposure Statement:
This equipment complies with the US/Canada portable RF exposure limits set forth for an uncontrolled environment
and are safe for the intended operation as described in this manual. Further RF exposure reduction can be
achieved if the product is kept as far as possible from your body, and the device can be set to lower output power, if
such function is available.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
SAR compliance has been established in typical laptop computer(s) with a USB port. Other applications, like
handheld PCs or similar devices, have not been verified and may not comply with related RF exposure rules; such
use shall be prohibited.
The USB dongle transmitter is approved for use in typical laptop computers. To comply with FCC RF exposure
requirements, a USB dongle transmitter should not be used certain laptop and tablet computer configurations where
the USB connectors on the host computer are unable to provide or ensure the necessary operating configurations
intended for the device and its users or bystanders to satisfy RF exposure compliance requirements.
The availability of some specific channels and/or operational frequency bands are country dependent and are
firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the
end user.
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Radiation Exposure Statement:
This product complies with the US/Canada portable RF exposure limits set forth for an uncontrolled environment
and are safe for intended operation as described in this manual. Further RF exposure reduction can be achieved if
the product is kept as far as possible from your body, or you can set the device to a lower power output setting, if
such function is available.
Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de
licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de
brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de
provoquer un fonctionnement indésirable.
NOTE IMPORTANTE:
Déclaration d’exposition aux radiations:
Le produit est conforme aux limites d’exposition pour les appareils portables RF pour les Etats-Unis et le Canada
établies pour un environnement non contrûlé.
Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction aux expositions RF peut être
augmentée si l’appareil peut être conservé aussi loin que possible du corps de l’utilisateur ou que le dispositif est
réglé sur la puissance de sortie la plus faible si une telle fonction est disponible.
Europe – EU Declaration of Conformity
Marking with the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the
European Union (1999/5/EC).
This equipment meets the following conformance standards:
• EN300 328 (2.4Ghz), EN301 489-17, EN60950-1
• This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and
EFTA countries, except in France and Italy where restrictive use applies.
Appendix C. Notification of Compliance
41
New Template User Manual
• In Italy, the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to
use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or
network services.
• This device may not be used for setting up outdoor radio links in France, and in some areas the RF output power
may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information contact the
national spectrum authority in France.
For complete DoC, visit the NETGEAR EU Declarations of Conformity website at:
http://kb.netgear.com/app/answers/detail/a_id/11621
Table 2. EDOC in Languages of the European Community
Language
Statement
Cesky [Czech]
NETGEAR Inc. tímto prohlašuje, že tento Radiolan je ve shode se základními
požadavky a dalšími príslušnými ustanoveními smernice 1999/5/ES.
Dansk [Danish]
Undertegnede NETGEAR Inc. erklærer herved, at følgende udstyr Radiolan
overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch [German]
Hiermit erklärt NETGEAR Inc., dass sich das Gerät Radiolan in Übereinstimmung mit
den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen
der Richtlinie 1999/5/EG befindet.
Eesti [Estonian]
Käesolevaga kinnitab NETGEAR Inc. seadme Radiolan vastavust direktiivi 1999/5/EÜ
põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
English
Hereby, NETGEAR Inc., declares that this Radiolan is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
Español [Spanish]
Por medio de la presente NETGEAR Inc. declara que el Radiolan cumple con los
requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la
Directiva 1999/5/CE.
Ελληνική [Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ NETGEAR Inc. ΔΗΛΩΝΕΙ ΟΤΙ Radiolan ΣΥΜΜΟΡΦΩΝΕΤΑΙ
ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ
ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Français [French]
Par la présente NETGEAR Inc. déclare que l'appareil Radiolan est conforme aux
exigences essentielles et aux autres dispositions pertinentes de la directive
1999/5/CE.
Italiano [Italian]
Con la presente NETGEAR Inc. dichiara che questo Radiolan è conforme ai requisiti
essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski [Latvian]
Ar šo NETGEAR Inc. deklarē, ka Radiolan atbilst Direktīvas 1999/5/EK būtiskajām
prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių [Lithuanian]
Šiuo NETGEAR Inc. deklaruoja, kad šis Radiolan atitinka esminius reikalavimus ir
kitas 1999/5/EB Direktyvos nuostatas.
Nederlands [Dutch]
Hierbij verklaart NETGEAR Inc. dat het toestel Radiolan in overeenstemming is met
de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Malti [Maltese]
Hawnhekk, NETGEAR Inc., jiddikjara li dan Radiolan jikkonforma mal-htigijiet
essenzjali u ma provvedimenti ohrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Magyar [Hungarian
Alulírott, NETGEAR Inc. nyilatkozom, hogy a Radiolan megfelel a vonatkozó alapvetõ
követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
42 | Appendix C. Notification of Compliance
New Template User Manual
Table 2. EDOC in Languages of the European Community
Language
Statement
Polski [Polish]
Niniejszym NETGEAR Inc. oświadcza, że Radiolan jest zgodny z zasadniczymi
wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português [Portuguese] NETGEAR Inc. declara que este Radiolan está conforme com os requisitos
essenciais e outras disposições da Directiva 1999/5/CE.
Slovensko [Slovenian]
NETGEAR Inc. izjavlja, da je ta Radiolan v skladu z bistvenimi zahtevami in ostalimi
relevantnimi določili direktive 1999/5/ES.
Slovensky [Slovak]
NETGEAR Inc. týmto vyhlasuje, že Radiolan spĺňa základné požiadavky a všetky
príslušné ustanovenia Smernice 1999/5/ES.
Suomi [Finnish]
NETGEAR Inc. vakuuttaa täten että Radiolan tyyppinen laite on direktiivin 1999/5/EY
oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Svenska [Swedish]
Härmed intygar NETGEAR Inc. att denna Radiolan står I överensstämmelse med de
väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv
1999/5/EG.
Íslenska [Icelandic]
Hér með lýsir NETGEAR Inc. yfir því að Radiolan er í samræmi við grunnkröfur og
aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.
Norsk [Norwegian]
NETGEAR Inc. erklærer herved at utstyret Radiolan er i samsvar med de
grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.
GPL License Agreement
GPL may be included in this product; to view the GPL license agreement go to
ftp://downloads.netgear.com/files/GPLnotice.pdf.
For GNU General Public License (GPL) related information, please visit
http://kbserver.netgear.com/kb_web_files/open_src.asp .
Interference Reduction Table
The table below shows the Recommended Minimum Distance between NETGEAR equipment and household
appliances to reduce interference (in feet and meters).
Household Appliance
Recommended Minimum Distance
(in feet and meters)
Microwave ovens
30 feet / 9 meters
Baby Monitor - Analog
20 feet / 6 meters
Baby Monitor - Digital
40 feet / 12 meters
Cordless phone - Analog
20 feet / 6 meters
Cordless phone - Digital
30 feet / 9 meters
Bluetooth devices
20 feet / 6 meters
ZigBee
20 feet / 6 meters
Appendix C. Notification of Compliance
43

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
Tagged PDF                      : Yes
Page Mode                       : UseOutlines
XMP Toolkit                     : 3.1-701
Copyright                       : ? 2011
Producer                        : Acrobat Distiller 9.2.0 (Windows)
Keywords                        : 
Format                          : application/pdf
Title                           : N150 Wireless Micro USB Adapter WNA1000M
Creator                         : NETGEAR, Inc.
Description                     : NETGEAR N150 Wireless Micro USB Adapter WNA1000M
Create Date                     : 2011:01:27 12:27:02Z
Creator Tool                    : FrameMaker 9.0
Modify Date                     : 2011:03:03 16:40:36+08:00
Metadata Date                   : 2011:03:03 16:40:36+08:00
Document ID                     : uuid:09ebfbe0-9b9a-4f2b-9427-c3f58bf5efd3
Instance ID                     : uuid:37571286-5e21-4c0b-9149-9585eb6a62d5
Page Count                      : 43
Subject                         : NETGEAR N150 Wireless Micro USB Adapter WNA1000M
Author                          : NETGEAR, Inc.
EXIF Metadata provided by EXIF.tools
FCC ID Filing: PY310400152

Navigation menu