Netgear orporated 12400218 R6200 Smart Wifi Router User Manual R6300v2 Smart WiFi Router

Download:
Mirror Download [FCC.gov]
Document ID	1983337
Application ID	7wC2AmQy1C1SxUlVp9wpEw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	329.58kB (4119756 bits)
Date Submitted	2013-06-05 00:00:00
Date Available	2013-12-03 00:00:00
Creation Date	2017-10-27 04:42:34
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-27 04:42:34
Document Title	R6300v2 Smart WiFi Router User Manual
Document Creator	FrameMaker 10.0.2
Document Author:	NETGEAR, Inc.

R6200v2 Smart WiFi Router
Installation Guide
NOTE: This document is for certification
purposes. Images are for position only and may
differ from the actual product.
May 2013
202-11202-01
350 East Plumeria Drive
San Jose, CA 95134
USA
R6200v2 Smart WiFi Router
Support
Thank you for selecting NETGEAR products.
After installing your device, locate the serial number on the label of your product and use it to register your product
at https://my.netgear.com. You must register your product before you can use NETGEAR telephone support.
NETGEAR recommends registering your product through the NETGEAR website. For product updates and web
support, visit http://support.netgear.com.
Phone (US & Canada only): 1-888-NETGEAR.
Phone (Other Countries): Check the list of phone numbers at
http://support.netgear.com/general/contact/default.aspx.
Trademarks
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of
NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change
without notice. © NETGEAR, Inc. All rights reserved.
Contents
Chapter 1
Hardware Setup
Unpack Your Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Hardware Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Front and Side Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Label. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Position Your Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Chapter 2
Getting Started
Router Setup Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Use Standard TCP/IP Properties for DHCP . . . . . . . . . . . . . . . . . . . . . . 13
Gather ISP Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Wireless Devices and Security Settings . . . . . . . . . . . . . . . . . . . . . . . . . 13
Types of Logins and Access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
NETGEAR genie Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Use NETGEAR genie After Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Upgrade the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Dashboard (Basic Home Screen). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Join Your Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Manual Method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Wi-Fi Protected Setup (WPS) Method . . . . . . . . . . . . . . . . . . . . . . . . . . 17
NETGEAR genie App and Mobile genie App . . . . . . . . . . . . . . . . . . . . . . . 18
Chapter 3
NETGEAR genie Basic Settings
Internet Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Internet Setup Screen Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Parental Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Basic Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Wireless Settings Screen Fields. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Change the Wireless Security Option. . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Set Up a Guest Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
View Attached Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Chapter 4
NETGEAR genie Advanced Home
NETGEAR genie Advanced Home Screen . . . . . . . . . . . . . . . . . . . . . . . . 31
Internet Connection Setup Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
WAN Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Default DMZ Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
R6200v2 Smart WiFi Router
Change the MTU Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
LAN Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
LAN Setup Screen Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Role of the Router as a DHCP Server . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Set Up Address Reservation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
WPS Wizard for WiFi Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Quality of Service (QoS) Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
WMM QoS for Wireless Multimedia Applications . . . . . . . . . . . . . . . . . . 39
Set Up Bandwidth Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Set Up QoS for Internet Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Chapter 5 USB Storage
Connect a USB Storage Device to the Router . . . . . . . . . . . . . . . . . . . . . . 46
Safely Remove a USB Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Access the USB Storage Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Sharing Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Share Photos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Store Files in a Central Location for Printing . . . . . . . . . . . . . . . . . . . . . 49
Share Large Files over the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
View a USB Device Attached to the Router . . . . . . . . . . . . . . . . . . . . . . . . 50
USB Storage Device Network and Access Settings. . . . . . . . . . . . . . . . . . 51
Available Network Folders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Specify Approved USB Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Media Server Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
TiVo Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Use ReadyDLNA to Play Media from Your Network on TiVo . . . . . . . . . 56
Chapter 6 ReadySHARE Printer
ReadySHARE Printer Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Set Up the ReadySHARE Printer Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Install the NETGEAR USB Control Center. . . . . . . . . . . . . . . . . . . . . . . . . 60
Set Up the NETGEAR USB Control Center . . . . . . . . . . . . . . . . . . . . . . . . 61
Configure the NETGEAR USB Control Center. . . . . . . . . . . . . . . . . . . . . . 63
Manage USB Print and Scan Jobs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Launch the NETGEAR USB Control Center. . . . . . . . . . . . . . . . . . . . . . 65
Use the Scan Feature of a Multifunction USB Printer . . . . . . . . . . . . . . 66
Chapter 7 Security
Keyword Blocking of HTTP Traffic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Block Services (Port Filtering) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Port Triggering to Open Incoming Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Port Forwarding to Permit External Host Communications . . . . . . . . . . . . 71
How Port Forwarding Differs from Port Triggering . . . . . . . . . . . . . . . . . . . 72
Set Up Port Forwarding to Local Servers. . . . . . . . . . . . . . . . . . . . . . . . . . 73
Add a Custom Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Edit or Delete a Port Forwarding Entry. . . . . . . . . . . . . . . . . . . . . . . . . . 75
R6200v2 Smart WiFi Router
Set Up Port Triggering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Schedule Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Set up Security Event Email Notifications . . . . . . . . . . . . . . . . . . . . . . . . .78
Chapter 8
Administration
Upgrade the Router Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
View Router Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Router Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Internet Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Wireless Settings (2.4 GHz and 5 GHz) . . . . . . . . . . . . . . . . . . . . . . . . .85
View Logs of Web Access or Attempted Web Access . . . . . . . . . . . . . . . .86
Manage the Configuration File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Back Up Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Restore Configuration Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Erase the Current Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . .88
Change the Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Password Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Chapter 9
Advanced Settings
Advanced Wireless Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Control the Wireless Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Set Up a Wireless Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
View or Change WPS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
Set Up a Wireless Access List by MAC Address . . . . . . . . . . . . . . . . . .93
Wireless Access Point (AP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
Set Up the Router in Bridge Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
Wireless Distribution System (WDS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
Set Up the Base Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Set Up a Repeater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Dynamic DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Static Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Remote Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
Universal Plug and Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
IPv6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Requirements for Entering IPv6 Addresses . . . . . . . . . . . . . . . . . . . . .107
Auto Detect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
IPv6 Auto Config. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108
IPv6 6to4 Tunnel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109
IPv6 Pass Through . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
IPv6 Fixed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
IPv6 DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
IPv6 PPPoE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Traffic Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Chapter 10
Troubleshooting
Quick Tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
R6200v2 Smart WiFi Router
Sequence to Restart Your Network . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Check Ethernet Cable Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Troubleshoot with the LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Power/Test LED Is Off or Blinking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Power/Test LED Stays Amber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
LEDs Never Turn Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Internet or Ethernet Port LEDs Are Off. . . . . . . . . . . . . . . . . . . . . . . . . 120
Wireless LEDs Are Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
The Push 'N' Connect (WPS) Button Blinks Amber . . . . . . . . . . . . . . . 120
Cannot Log In to the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Cannot Access the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Troubleshoot PPPoE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Troubleshoot Internet Browsing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Changes Not Saved . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Wireless Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Wireless Signal Strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Troubleshoot Your Network Using the Ping Utility . . . . . . . . . . . . . . . . . . 125
Test the LAN Path to Your Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Test the Path from Your Computer to a Remote Device . . . . . . . . . . . 126
Appendix A Supplemental Information
Factory Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Appendix B Notification of Compliance
1.
Hardware Setup
Get t ing to kno w yo ur r out er
The R6200v2 Smart WiFi Router with AC dual band delivers 300 TO 867 WiFi and Gigabit
Ethernet speeds. It offers the best wireless coverage for large homes and is ideal for homes with
ten or more wireless devices.
Compatible with next generation WiFi devices and backward compatible with 802.11 a/b/g/n
devices, it enables HD streaming throughout your home. With up to 3001 to 8672 Mbps speed
and simultaneous dual-band WiFi technology, the R6200v2 avoids wireless interference,
ensuring top WiFi speeds and reliable connections.
If you already set up your router, you can skip this chapter. If you have not done that yet, this
chapter covers the hardware setup. Chapter 2, Getting Started, explains how to access your
router to view or change its settings.
This chapter contains the following sections:
•
Unpack Your Router
•
Hardware Features
•
Position Your Router
For more information about the topics covered in this manual, visit the support website at
http://support.netgear.com.
1. Maximum wireless signal rate derived from IEEE standard 802.11 specifications. Actual data throughput and wireless coverage will vary. Network
conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual
data throughput rate and wireless coverage. NETGEAR makes no express or implied representations or warranties about this product’s compatibility
with any future standards.
2. Up to 867Mbps wireless speeds achieved when connecting to other 802.11ac 867 Mbps devices.
R6200v2 Smart WiFi Router
Unpack Your Router
Open the box and remove the router, cables, and installation guide.
Ethernet cable with internal shielding
Smart WiFi Router
Power adapter
Figure 1. Check the package contents
Your box contains the following items:
•
R6200v2 Smart WiFi Router
•
AC power adapter (plug varies by region)
•
Category 5 (Cat 5) Ethernet cable1
•
Installation guide with cabling and router setup instructions
If any parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the
carton and original packing materials, in case you return the product for repair.
Hardware Features
Before you cable your router, take a moment to become familiar with the front, side, and back
panels and the label. Pay particular attention to the LEDs on the front panel.
1. All cables used to connect peripherals must be shielded and grounded. Operation with cables connected to peripherals that are not sheilded and
grounded may result interference to radio and television reception.
Hardware Setup
R6200v2 Smart WiFi Router
Front and Side Panels
The router front panel has the status LEDs and icons shown in the following figure.
WiFi On/Off button
WPS button
LEDs
Figure 2. Router front and side view
Table 1. Front panel LED descriptions
LED
Description
Power
•
•
•
•
•
Solid amber. The router is starting up.
Blinking amber. The firmware is upgrading, or the Reset button was pressed.
Solid green. The router is ready.
Blinking green. The firmware is corrupted. Visit www.netgear.com/support.
Off. Power is not supplied to the router.
Internet
•
•
•
Solid green. The Internet connection is ready.
Solid amber. The Ethernet cable connection to the modem has been detected.
Off. No Ethernet cable is connected to the modem.
Wireless
•
•
•
Solid blue. The wireless radio is operating in either 2.4 GHz or 5 GHz mode.
Blinking. The router is in WPS mode.
Off. The wireless radios are off for both 2.4 GHz and 5 GHz.
USB
•
•
•
Solid blue. The router has accepted the USB device. The USB device is ready to be used.
Blinking blue. A USB device is plugged in and is trying to connect.
Off. No USB device is connected; someone clicked the Safely Remove Hardware button, and
it is now safe to remove the attached USB device.
Hardware Setup
R6200v2 Smart WiFi Router
The WiFi and WPS buttons toggle the WiFi and WPS functions on and off.
•
WiFi On/Off button. Pressing and holding this button for 2 seconds turns on and off the
2.4 GHz and 5 GHz wireless radios. If the Wireless LED is lit, the wireless radios are on.
If this LED is off, the wireless radios are turned off and you cannot connect wirelessly to
the router.
•
WPS button. You can use this button to use WPS to add a wireless device or computer
to your wireless network. The Wireless LED blinks blue when the router is trying to add
the wireless device or computer. The LED stays solid blue when wireless security is
enabled in the router.
Rear Panel
The rear panel has the connections and buttons shown in the following figure.
Power connector
Power On/Off
USB 3.0
port
Ethernet
LAN ports 1–4
Internet
port
Reset
button
Figure 3. Router rear panel
The Reset button restores the factory settings. See Factory Settings on page 128.
Hardware Setup
10
R6200v2 Smart WiFi Router
Label
The label on the bottom of the router shows the WPS PIN, login information, MAC address,
and serial number.
Default access information
Preset WiFi
password
Serial number and
MAC address
Figure 4. The label shows unique information about your router
Position Your Router
The router lets you access your network from anywhere within the operating range of your
wireless network. However, the operating distance or range of your wireless connection can
vary significantly depending on the physical placement of your router. For example, the
thickness and number of walls the wireless signal passes through can limit the range. For
best results, place your router:
•
Near the center of the area where your computers and other devices operate, and
preferably within line of sight to your wireless devices.
•
So it is accessible to an AC power outlet and near Ethernet cables for wired computers.
•
In an elevated location such as a high shelf, keeping the number of walls and ceilings
between the router and your other devices to a minimum.
•
Away from electrical devices that are potential sources of interference. Equipment that
might cause interference includes ceiling fans, home security systems, microwaves,
computers, the base of a cordless phone, or a 2.4 GHz cordless phone.
•
Away from any large metal surfaces, such as a solid metal door or aluminum studs. Large
expanses of other materials such as glass, insulated walls, fish tanks, mirrors, brick, and
concrete can also affect your wireless signal.
Hardware Setup
11
2.
Getting Started
C onnec ting to th e ro ut er
This chapter explains how to use NETGEAR genie to set up your router after you complete
cabling as described in the installation guide.
This chapter contains the following sections:
•
Router Setup Preparation
•
Types of Logins and Access
•
NETGEAR genie Setup
•
Use NETGEAR genie After Installation
•
Upgrade the Firmware
•
Dashboard (Basic Home Screen)
•
Join Your Wireless Network
•
NETGEAR genie App and Mobile genie App
12
R6200v2 Smart WiFi Router
Router Setup Preparation
You can set up your router with the NETGEAR genie automatically, or you can use the genie
menus and screens to set up your router manually. Before you start the setup process, get
your ISP information and make sure the computers and devices in the network have the
settings described here.
Use Standard TCP/IP Properties for DHCP
If you set up your computer to use a static IP address, change the settings so that it uses
Dynamic Host Configuration Protocol (DHCP).
Gather ISP Information
If you have DSL broadband service, you might need the following information to set up your
router and to check that your Internet configuration is correct. When your Internet service
starts, your Internet service provider (ISP) typically gives you all the information needed to
connect to the Internet. If you cannot locate this information, ask your ISP to provide it. When
your Internet connection is working, you no longer need to launch the ISP login program on
your computer to access the Internet. When you start an Internet application, your router
automatically logs you in.
•
The ISP configuration information for your DSL account
•
ISP login name and password
•
Fixed or static IP address settings (special deployment by ISP; this setting is rare)
Wireless Devices and Security Settings
Make sure that the wireless device or computer that you are using supports WPA or WPA2
wireless security, which is the wireless security that the router uses.
Types of Logins and Access
Separate types of logins have different purposes. It is important that you understand the
difference so that you know which login to use when.
•
Router login logs you in to the router interface from NETGEAR genie. For details about
this login, see Use NETGEAR genie After Installation on page 15.
•
ISP login logs you in to your Internet service. Your service provider has provided you with
this login information in a letter or some other way. If you cannot find this login
information, contact your service provider.
•
Wireless network key or password. Your router is preset with a unique wireless
network name (SSID) and password for wireless access. This information is on the label
on the bottom of your router.
Getting Started
13
R6200v2 Smart WiFi Router
NETGEAR genie Setup
NETGEAR genie runs on any device with a web browser. Installation and basic setup takes
about 15 minutes to complete.

To use NETGEAR genie to set up your router:
1. Turn the router on by pressing the On/Off button.
2. Make sure that your computer or wireless device is connected to the router with an Ethernet
cable (wired) or wirelessly with the preset security settings listed on the bottom label.
3. Launch your Internet browser.
• The first time you set up the Internet connection for your router, the browser goes to
http://www.routerlogin.net, and the NETGEAR genie screen displays.
•
If you already used the NETGEAR genie, type http://www.routerlogin.net in the
address field for your browser to display the NETGEAR genie screen. See Use
NETGEAR genie After Installation on page 15.
4. Follow the onscreen instructions.
NETGEAR genie guides you through connecting the router to the Internet.
If the browser cannot display the web page:
•
Make sure that the computer is connected to one of the four LAN Ethernet ports or
wirelessly to the router.
•
Make sure that the router has full power, and that its WiFi LED is lit.
•
Close and reopen the browser or clear the browser cache.
•
Browse to http://www.routerlogin.net.
•
If the computer is set to a static or fixed IP address (this setting is uncommon), change it
to obtain an IP address automatically from the router.
Getting Started
14
R6200v2 Smart WiFi Router
If the router does not connect to the Internet:
1. Review your settings. Make sure that you have selected the correct options and typed
everything correctly.
2. Contact your ISP to verify that you have the correct configuration information.
3. Read Chapter 10, Troubleshooting. If problems persist, register your NETGEAR product and
contact NETGEAR technical support.
Use NETGEAR genie After Installation
When you first set up your router, NETGEAR genie automatically starts when you launch an
Internet browser on a computer that is connected to the router. If you want to view or change
settings for the router, you can use genie again.
1. Launch your browser from a computer or wireless device that is connected to the router.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login window displays.
3. Enter admin for the router user name and password for the router password, both in
lowercase letters.
Note: The router user name and password are different from the user name
and password for logging in to your Internet connection. For more information,
see Types of Logins and Access on page 13.
Upgrade the Firmware
When you set up your router and connect to the Internet, the router automatically checks to
see if newer firmware is available. If it is, a message is displayed on the top of the screen.

To upgrade the firmware:
1. Click the message that tells you new firmware is available.
During the firmware upgrade, you cannot access the Internet.
2. Click Yes to upgrade the router with the latest firmware.
WARNING:
To avoid the risk of corrupting the firmware, do not interrupt the
upgrade. For example, do not close the browser, click a link, or
load a new page. Do not turn off the router.
After the upgrade, the router restarts.
For more information, see Upgrade the Router Firmware on page 81
Getting Started
15
R6200v2 Smart WiFi Router
Dashboard (Basic Home Screen)
The router Basic Home screen has a dashboard that lets you see the status of your Internet
connection and network at a glance. You can click any of the six sections of the dashboard to
view and change the settings. The left column has menus. You can use the ADVANCED tab
to access more menus and screens.
Language
Dashboard
(Click to
view details)
Menus
(Click the
Advanced
tab to view
more)
FOR POSITION ONLY
Help
Figure 5. Basic Home screen with dashboard, language, and online help
•
Home. This dashboard screen displays when you log in to the router.
•
Internet. Set, update, and check the ISP settings of your router.
•
Wireless. View or change the wireless settings for your router.
•
Attached Devices. View the devices connected to your network.
•
Parental Controls. Download and set up parental controls to prevent objectionable
content from reaching your computers.
•
ReadySHARE. If you connected a USB storage device to the router, then it is displayed
here.
•
Guest Network. Set up a guest network to allow visitors to use your router’s Internet
connection.
•
Advanced tab. Set the router up for unique situations such as when remote access by IP
or by domain name from the Internet is needed. See Chapter 9, Advanced Settings. You
need a solid understanding of networking to use this tab.
•
Help & Support. Visit the NETGEAR support site for information, help, and product
documentation. These links work once you have an Internet connection.
Getting Started
16
R6200v2 Smart WiFi Router
Join Your Wireless Network
You can use the manual or the WPS method to join your wireless network. For instructions
about how to set up a guest network, see Set Up a Guest Network on page 28.
Manual Method
With the manual method, choose the network that you want and type its password to
connect.

To connect manually:
1. On your computer or wireless device, open the software that manages your wireless
connections.
This software scans for all wireless networks in your area.
2. Look for your network and select it.
The unique WiFi network name (SSID) and password are on the router label. If you
changed these settings, look for the network name that you used.
3. Enter the router password and click Connect.
Wi-Fi Protected Setup (WPS) Method
Wi-Fi Protected Setup (WPS) lets you connect to a secure WiFi network without typing its
password. Instead, press a button or enter a PIN. NETGEAR calls WPS Push 'N' Connect.
Some older WiFi equipment is not compatible with WPS. WPS works only with WPA2 or WPA
wireless security.

To use WPS to join the wireless network:
1. Press the WPS button on the side of the router.
2. Within 2 minutes, press the WPS button on your wireless device, or follow the WPS
instructions that came with the device.
The WPS process automatically sets up your wireless computer with the network
password and connects you to the wireless network.
Getting Started
17
R6200v2 Smart WiFi Router
NETGEAR genie App and Mobile genie App
The genie app is the easy dashboard for managing, monitoring, and repairing your home
network. See the NETGEAR genie App User Manual for details about the genie apps.
Retrieve wireless password
About genie
Language
Menu
Dashboard
(Click to
view
details)
Support
Figure 6. genie app dashboard
The genie app can help you with the following:
•
Automatically repair common wireless network problems.
•
Have easy access to router features like Live Parental Controls, guest access, Internet
traffic meter, speed test, and more.
The genie mobile app works on your iPhone, iPad, or Android phone:
Phone status
Information about
genie mobile app
and the connected
router
Log in to the router
Search NETGEAR
support
Figure 7. genie mobile app home screen
Getting Started
18
3.
NETGEAR genie Basic Settings
Your Inte rne t co nn ection and W iFi net wor k
This chapter contains the following sections:
•
Internet Setup
•
Parental Controls
•
Basic Wireless Settings
•
Set Up a Guest Network
•
View Attached Devices
For information about the ReadySHARE feature on the BASIC Home tab, see Chapter 5, USB
Storage and Chapter 6, ReadySHARE Printer.
19
R6200v2 Smart WiFi Router
Internet Setup
The Internet Setup screen is where you view or change basic ISP information.
Note: You can use the Setup Wizard to detect the Internet connection and
automatically set up the router. See Internet Connection Setup
Wizard on page 31.

To view or change the basic Internet setup:
1. From the Home screen, select Internet.
Scroll to
view more
settings
The fields that display in the Internet Setup screen depend on whether your Internet
connection requires a login.
2. Select the Yes or No radio button.
• Yes. Select the encapsulation method and enter the login name. If you want to
change the login time-out, enter a new value in minutes.
•
No. Enter the account and domain names, only if needed.
3. Enter the settings for the IP address and DNS server.
The default settings usually work fine. If you have problems with your connection, check
the ISP settings.
4. Click Apply.
Your settings are saved.
5. Click Test to test your Internet connection.
NETGEAR genie Basic Settings
20
R6200v2 Smart WiFi Router
If the NETGEAR website does not display within 1 minute, see Chapter 10,
Troubleshooting.
Internet Setup Screen Fields
The following descriptions explain all of the possible fields in the Internet Setup screen. The
fields that display in this screen depend on whether tan ISP login is required.
Does Your Internet connection require a login? Answer either yes or no.
These fields display when no login is required:
•
Account Name (If required). Enter the account name provided by your ISP. This might
also be called the host name.
•
Domain Name (If required). Enter the domain name provided by your ISP.
These fields display when your ISP requires a login:
•
Internet Service Provider. PPPoE or PPPoA.
•
Login. The login name provided by your ISP. This login name is often an email address.
•
Password. The password that you use to log in to your ISP.
•
Service Name (if Required). If your ISP provided a service name, enter it here.
•
Connection Mode. Always On, Dial on Demand, or Manually Connect.
•
Idle Timeout (In minutes). If you want to change the login time-out, enter a new value in
minutes. This setting determines how long the router keeps the Internet connection active
when there is no Internet activity from the LAN. A value of 0 (zero) means never log out.
Internet IP Address.
•
Get Dynamically from ISP. Your ISP uses DHCP to assign your IP address. Your ISP
automatically assigns these addresses.
•
Use Static IP Address. Enter the IP address, IP subnet mask, and the gateway IP
address that your ISP assigned. The gateway is the ISP router to which your router
connects.
Domain Name Server (DNS) Address. The DNS server is used to look up site addresses
based on their names.
•
Get Automatically from ISP. Your ISP uses DHCP to assign your DNS servers. Your ISP
automatically assigns this address.
•
Use These DNS Servers. If you know that your ISP requires specific servers, select this
option. Enter the IP address of your ISP’s primary DNS server. If a secondary DNS server
address is available, enter it also.
NAT (Network Address Translation). NAT allows computers on your home network to
share the router Internet connection. NAT is enabled by default because it is needed in most
situations. The following settings are available:
•
Enable
•
Disable
NETGEAR genie Basic Settings
21
R6200v2 Smart WiFi Router
•
Disable Port Scan and DoS Protection
Router MAC Address. The Ethernet MAC address that the router uses on the Internet port.
Some ISPs register the MAC address of the network interface card in your computer when
your account is first opened. They accept traffic only from the MAC address of that computer.
This feature allows your router to use your computer’s MAC address (also called cloning).
•
Use Default Address. Use the default MAC address.
•
Use Computer MAC Address. The router captures and uses the MAC address of the
computer that you are now using. You have to use the one computer that the ISP allows.
•
Use This MAC Address. Enter the MAC address that you want to use.
Parental Controls
The first time you select Parental Controls from the Basic Home screen, your browser goes to
the Live Parental Controls website. You can learn more about Live Parental Controls or
download the application.

To set up Live Parental Controls:
1. Select Parental Controls on the dashboard screen.
2. Click either the Windows Users or Mac Users button.
3. Follow the onscreen instructions to download and install the NETGEAR Live Parental
Controls Management utility.
NETGEAR genie Basic Settings
22
R6200v2 Smart WiFi Router
After installation, Live Parental Controls automatically starts.
4. Click Next, read the note, and click Next again to proceed.
Because Live Parental Controls uses free OpenDNS accounts, you are prompted to log
in or create a free account.
5. Select the radio button that applies to you and click Next.
• If you already have an OpenDNS account, leave the Yes radio button selected.
•
If you do not have an OpenDNS account, select the No radio button.
If you are creating an account, the following screen displays:
•
Fill in the fields and click Next.
NETGEAR genie Basic Settings
23
R6200v2 Smart WiFi Router
After you log on or create your account, the filtering level screen displays:
6. Select the radio button for the filtering level that you want and click Next.
7. Click the Take me to the status screen button.
Parental controls are now set up for the router. The dashboard shows Parental Controls as
Enabled.
Basic Wireless Settings
The Wireless Settings screen lets you view or configure the wireless network setup.
The router comes with preset security. This means that the Wi-Fi network name (SSID),
network key (password), and security option (encryption protocol) are preset in the factory.
You can find the preset SSID and password on the bottom of the unit.
Note: The preset SSID and password are uniquely generated for every
device to protect and maximize your wireless security.
NETGEAR genie Basic Settings
24
R6200v2 Smart WiFi Router
NETGEAR recommends that you do not change your preset security settings. If you change
your preset security settings, make a note of the new settings and store it in a safe place
where you can easily find it.
If you use a wireless computer to change the wireless network name (SSID) or other wireless
security settings, you are disconnected when you click Apply. To avoid this problem, use a
computer with a wired connection to access the router.

To view or change basic wireless settings:
1. Select Basic > Wireless.
The screen sections, settings, and procedures are explained in the following sections.
2. Make any changes that are needed.
3. Click Apply.
Your settings are saved.
If you were connected wirelessly to the router and you changed the SSID or wireless
security, you are disconnected from the network.
4. If you changed the settings, make sure that you can connect wirelessly to the network with
its new settings.
If you cannot connect wirelessly, check the following:
•
Is your computer or wireless device connected to another wireless network in your
area? Some wireless devices automatically connect to the first open network (without
wireless security) that they discover.
•
Is your computer or wireless device trying to connect to your network with its old
settings (before you made changes)? If so, update the wireless network selection in
your computer or wireless device to match the current settings for your network.
NETGEAR genie Basic Settings
25
R6200v2 Smart WiFi Router
Wireless Settings Screen Fields
You can use this screen to view or change the wireless network settings and the security
option.
Enable SSID Broadcast. This feature allows the router to broadcast its SSID so wireless
stations can see this wireless name (SSID) in their scanned network lists. This check box is
selected by default. To turn off the SSID broadcast, clear this check box, and click Apply.
Enable Wireless Isolation. If this check box is selected, computers or wireless devices that
join the network can use the Internet, but cannot access each other or access Ethernet
devices on the network.
Name (SSID). The SSID is also known as the wireless network name. Enter a 32-character
(maximum) name in this field. This field is case-sensitive. The default SSID is randomly
generated, and NETGEAR strongly recommends that you do not change this setting.
Region. The location where the router is used. Select from the countries in the list. In the
United States, the region is fixed to United States and is not changeable.
Channel. The wireless channel the router uses. For 2.4 GHz, select a value from 1 through
13. (For products in the North America market, only Channels 1 through 11 can be operated.)
Do not change the channel unless you experience interference (shown by lost connections or
slow data transfers). If this happens, experiment with different channels to see which is the
best.
When you use multiple access points, it is better if adjacent access points use different radio
frequency channels to reduce interference. The recommended channel spacing between
adjacent access points is four channels (for example, use Channels 1 and 5, or 6 and 10).
Mode. For 2.4 GHz, Up to 145 Mbps is the default setting, which allows 802.11n and 802.11g
wireless devices to join the network. The other settings are Up to 54 Mbps, and Up to 300
Mbps.
At 5GHz, Up to 867 Mbps is the default setting, which allows 802.11ac and 802.11a wireless
devices to join the network. The other settings are Up to 173 Mbps and 400 Mbps.
Security Options. The router comes with unique preset wireless security. These settings are
on the product label. NETGEAR recommends that you use preset security so that you can
refer to the label if you forget the WiFi password. However, you can change the security
option and passphrase.
Wireless Security Options
A security option is the type of security protocol applied to your wireless network. The
security protocol in force encrypts data transmissions and ensures that only trusted devices
receive authorization to connect to your network. Wi-Fi Protected Access (WPA) has several
options including pre-shared key (PSK) encryption.
WPA encryption is built into all hardware that has the Wi-Fi-certified seal. This seal means
that the product is authorized by the Wi-Fi Alliance (http://www.wi-fi.org/) because it complies
with the worldwide single standard for high-speed wireless local area networking.
NETGEAR genie Basic Settings
26
R6200v2 Smart WiFi Router
WPA uses a passphrase for authentication and to generate the initial data encryption keys.
Then it dynamically varies the encryption key. WPA-PSK uses Temporal Key Integrity
Protocol (TKIP) data encryption, implements most of the IEEE 802.11i standard, and works
with all wireless network interface cards, but not all wireless access points.
WPA2-PSK is stronger than WPA-PSK. It is advertised to be theoretically indecipherable due
to the greater degree of randomness in encryption keys that it generates. WPA2-PSK gets
higher speed because it is implemented through hardware, while WPA-PSK is usually
implemented through software. WPA2-PSK uses a passphrase to authenticate and generate
the initial data encryption keys. Then it dynamically varies the encryption key.
WPS-PSK + WPA2-PSK Mixed Mode can provide broader support for all wireless clients.
WPA2-PSK clients get higher speed and security, and WPA-PSK clients get decent speed
and security. For help with WPA settings on your wireless computer or device, see the
instructions that came with your product.
Change the Wireless Security Option
NETGEAR recommends that you do not disable security.

To change the WPA settings:
1. Select Basic > Wireless Settings.
2. Under Security Options, select the WPA option you want.
3. In the Passphrase field that displays when you select a WPA security option, enter the
network key (password) that you want to use. It is a text string from 8 to 63 characters.
4. Write down the new password and keep it in a secure place for future reference.
5. Click Apply.
Your changes are saved.
NETGEAR genie Basic Settings
27
R6200v2 Smart WiFi Router
Set Up a Guest Network
A guest network allows visitors at your home to use the Internet without using your wireless
security key. You can add a guest network to each wireless network: 2.4 GHz b/g/n and 5.0
GHz a/n.

To set up a guest network:
1. Select Basic > Guest Network.
2. Select any of the following wireless settings:
Enable Guest Network. When this check box is selected, the guest network is enabled,
and guests can connect to your network using the SSID of this profile.
Enable SSID Broadcast. If this check box is selected, the wireless access point
broadcasts its name (SSID) to all wireless stations. Stations with no SSID can adopt the
correct SSID for connections to this access point.
Allow guest to access My Local Network. If this check box is selected, anyone who
connects to this SSID has access to your local network, not just Internet access.
3. Give the guest network a name.
The guest network name is case-sensitive and can be up to 32 characters. You then
manually configure the wireless devices in your network to use the guest network name in
addition to the main SSID.
4. Select a security option from the list.
The security options are described in Wireless Security Options on page 26.
5. Click Apply.
Your settings are saved.
NETGEAR genie Basic Settings
28
R6200v2 Smart WiFi Router
View Attached Devices
You can view all computers or devices that are currently connected to your network.

To go to the Attached Devices screen:
1. From the Basic Home screen, select Attached Devices.
Wired devices are connected to the router with Ethernet cables. Wireless devices have
joined the wireless network. The following information is displayed:
•
# (number). The order in which the device joined the network.
•
IP Address. The IP address that the router assigned to this device when it joined the
network. This number can change if a device is disconnected and rejoins the network.
•
MAC Address. The unique MAC address for each device does not change. The MAC
address is typically shown on the product label.
•
Device Name. If the device name is known, it is shown here.
2. Click Refresh to update this screen.
NETGEAR genie Basic Settings
29
4.
NETGEAR genie Advanced Home
S pecifying cu sto m se t t ings
This chapter contains the following sections:
•
NETGEAR genie Advanced Home Screen
•
Internet Connection Setup Wizard
•
WAN Setup
•
LAN Setup
•
WPS Wizard for WiFi Connections
•
Quality of Service (QoS) Setup
Some selections on the Advanced Home screen are described in separate chapters:
•
USB Storage. See Chapter 5, USB Storage.
•
Security. See Chapter 7, Security.
•
Administration. See Chapter 8, Administration.
•
Advanced Setup. See Chapter 9, Advanced Settings.
30
R6200v2 Smart WiFi Router
NETGEAR genie Advanced Home Screen
The genie Advanced Home dashboard presents status information. The content is the same
as what is on the Router Status screen available from the Administration menu. See View
Router Status on page 82.
FOR POSITION ONLY
Internet Connection Setup Wizard
You can use the Setup Wizard to detect your Internet settings and automatically set up your
router. The Setup Wizard is not the same as the genie screens that display the first time you
connect to your router to set it up.

To use the Setup Wizard:
1. Select Advanced > Setup Wizard.
2. Select Yes.
If you select No, you are taken to the Internet Setup screen (see Internet Setup on
page 20).
3. Select your location.
4. Click Next.
NETGEAR genie Advanced Home
31
R6200v2 Smart WiFi Router
The Setup Wizard searches your Internet connection for servers and protocols to
determine your ISP configuration.
WAN Setup
The WAN Setup screen lets you configure a DMZ (demilitarized zone) server, change the
maximum transmit unit (MTU) size, and enable the router to respond to a ping on the WAN
(Internet) port.

To view or change the WAN settings:
1. Select Advanced > Setup > WAN Setup.
2. Specify the following settings:
• Disable Port Scan and DoS Protection. DoS protection protects your LAN against
denial of service attacks such as Syn flood, Smurf Attack, Ping of Death, Teardrop
Attack, UDP Flood, ARP Attack, Spoofing ICMP, Null Scan, and many others. This
setting should be disabled only in special circumstances.
•
Default DMZ Server. This feature is sometimes helpful when you are playing online
games or videoconferencing. Be careful when using this feature because it makes the
firewall security less effective. See the following section, Default DMZ Server.
•
Respond to Ping on Internet Port. If you want the router to respond to a ping from
the Internet, select this check box. Use this setting only as a diagnostic tool because it
NETGEAR genie Advanced Home
32
R6200v2 Smart WiFi Router
allows your router to be discovered. Do not select this check box unless you have a
specific reason.
•
Disable IGMP Proxying. IGMP proxying allows a computer on the local area network
(LAN) to receive the multicast traffic it is interested in from the Internet. If you do not
need this feature, you can select this check box to disable it.
•
MTU Size (in bytes). The normal MTU (maximum transmit unit) value for most
Ethernet networks is 1500 bytes, or 1492 bytes for PPPoE connections. For some
ISPs, you might need to reduce the MTU. Reduce the MTU only if you are sure that it
is necessary for your ISP connection. See Change the MTU Size on page 34.
•
NAT Filtering. Network Address Translation (NAT) determines how the router
processes inbound traffic. Secured NAT provides a secured firewall to protect the
computers on the LAN from attacks from the Internet, but might prevent some Internet
games, point-to-point applications, or multimedia applications from functioning. Open
NAT provides a much less secured firewall, but allows almost all Internet applications
to function.
3. Click Apply.
Your changes are saved.
Default DMZ Server
The default DMZ server feature is helpful when you are using some online games and
videoconferencing applications that are incompatible with Network Address Translation
(NAT). The router is programmed to recognize some of these applications and to work
correctly with them, but other applications might not function well. In some cases, one local
computer can run the application correctly if the IP address for that computer is entered as
the default DMZ server.
WARNING:
DMZ servers pose a security risk. A computer designated as the
default DMZ server loses much of the protection of the firewall
and is exposed to exploits from the Internet. If compromised, the
DMZ server computer can be used to attack other computers on
your network.
The router usually detects and discards incoming traffic from the Internet that is not a
response to one of your local computers or a service that you have configured in the Port
Forwarding/Port Triggering screen. Instead of discarding this traffic, you can have the router
forward the traffic to one computer on your network. This computer is called the default DMZ
server.

To set up a default DMZ server:
1. Select Advanced > Setup > WAN Setup.
2. Select the Default DMZ Server check box.
NETGEAR genie Advanced Home
33
R6200v2 Smart WiFi Router
3. Type the IP address.
4. Click Apply.
Your change takes effect.
Change the MTU Size
The maximum transmission unit (MTU) is the largest data packet a network device transmits.
When one network device communicates across the Internet with another, the data packets
travel through many devices along the way. If a device in the data path has a lower MTU
setting than the other devices, the data packets have to be split or “fragmented” to
accommodate the device with the smallest MTU.
The best MTU setting for NETGEAR equipment is often just the default value. In some
situations, changing the value fixes one problem but causes another. Leave the MTU
unchanged unless one of these situations occurs:
•
You have problems connecting to your ISP or other Internet service, and the technical
support of either the ISP or NETGEAR recommends changing the MTU setting. These
web-based applications might require an MTU change:
A secure website that does not open, or displays only part of a web page
Yahoo email
MSN portal
America Online’s DSL service
•
You use VPN and have severe performance problems.
•
You used a program to optimize MTU for performance reasons, and now you have
connectivity or performance problems.
Note: An incorrect MTU setting can cause Internet communication
problems. For example, you might not be able to access certain
websites, frames within websites, secure login pages, or FTP or
POP servers.
If you suspect an MTU problem, a common solution is to change the MTU to 1400. If you are
willing to experiment, you can gradually reduce the MTU from the maximum value of 1500
until the problem goes away. The following table describes common MTU sizes and
applications.
Table 2. Common MTU sizes
MTU
Application
1500
The largest Ethernet packet size. This setting is typical for connections that do not use
PPPoE or VPN, and is the default value for NETGEAR routers, adapters, and switches.
1492
Used in PPPoE environments.
NETGEAR genie Advanced Home
34
R6200v2 Smart WiFi Router
Table 2. Common MTU sizes (continued)

MTU
Application
1472
Maximum size to use for pinging. (Larger packets are fragmented.)
1468
Used in some DHCP environments.
1460
Usable by AOL if you do not have large email attachments, for example.
1436
Used in PPTP environments or with VPN.
1400
Maximum size for AOL DSL.
576
Typical value to connect to dial-up ISPs.
To change the MTU size:
1. Select Advanced > Setup > WAN Setup.
2. In the MTU Size field, enter a value from 64 to 1500.
3. Click Apply.
Your change is saved.
LAN Setup
The LAN Setup screen allows configuration of LAN IP services such as Dynamic Host
Configuration Protocol (DHCP) and Routing Information Protocol (RIP).
The router is shipped preconfigured to use private IP addresses on the LAN side and to act
as a DHCP server. The router’s default LAN IP configuration is:
•
LAN IP address. 192.168.1.1
•
Subnet mask. 255.255.255.0
These addresses are part of the designated private address range for use in private networks
and are suitable for most applications. If your network requires a different IP addressing
scheme, you can change these settings in the LAN Setup screen.
Note: If you change the LAN IP address of the router while connected
through the browser, you are disconnected. If you want to continue
to use the router menus, open a new connection to the new IP
address and log in again.
NETGEAR genie Advanced Home
35
R6200v2 Smart WiFi Router

To change the LAN settings:
1. Select Advanced > Setup > LAN Setup.
2. Enter the settings that you want to customize.
These settings are described in the following section, LAN Setup Screen Settings.
3. Click Apply.
Your changes are saved.
LAN Setup Screen Settings
LAN TCP/IP Setup
•
IP Address. The LAN IP address of the router.
•
IP Subnet Mask. The LAN subnet mask of the router. Combined with the IP address, the
IP subnet mask allows a device to know which other addresses are local to it, and which
have to be reached through a gateway or router.
•
RIP Direction. Router Information Protocol (RIP) allows a router to exchange routing
information with other routers. This setting controls how the router sends and receives
RIP packets. Both is the default setting. With the Both or Out Only setting, the router
broadcasts its routing table periodically. With the Both or In Only setting, the router
incorporates the RIP information that it receives.
•
RIP Version. This setting controls the format and the broadcasting method of the RIP
packets that the router sends. It recognizes both formats when receiving. By default, the
RIP function is disabled.
RIP-1 is universally supported. It is adequate for most networks, unless you have an
unusual network setup.
NETGEAR genie Advanced Home
36
R6200v2 Smart WiFi Router
RIP-2 carries more information. Both RIP-2B and RIP-2M send the routing data in
RIP-2 format. RIP-2B uses subnet broadcasting. RIP-2M uses multicasting.
Use Router as DHCP Server
For most home networks, this check box is selected so that the router acts as a Dynamic
Host Configuration Protocol (DHCP) server.
•
Starting IP Address. Specify the start of the range for the pool of IP addresses in the
same subnet as the router.
•
Ending IP Address. Specify the end of the range for the pool of IP addresses in the
same subnet as the router.
Address Reservation
When you specify a reserved IP address for a computer on the LAN, that computer receives
the same IP address each time it accesses the router’s DHCP server. Assign reserved IP
addresses to servers that require permanent IP settings. See Set Up Address Reservation on
page 38.
Role of the Router as a DHCP Server
By default, the router acts as a DHCP server. The router assigns IP, DNS server, and default
gateway addresses to all computers connected to the LAN. The assigned default gateway
address is the LAN address of the router. The router assigns IP addresses to the attached
computers from a pool of addresses specified in the LAN Setup screen. Each pool address is
tested before it is assigned to avoid duplicate addresses on the LAN. For most applications,
the default DHCP and TCP/IP settings of the router are satisfactory.
You can specify the pool of IP addresses that the router assigns by setting the starting IP
address and ending IP address. These addresses should be part of the same IP address
subnet as the router’s LAN IP address. Using the default addressing scheme, define a range
between 192.168.1.2 and 192.168.1.254, although you might want to save part of the range
for devices with fixed addresses.
The router delivers the following parameters to any LAN device that requests DHCP:
•
An IP address from the range you have defined
•
Subnet mask
•
Gateway IP address (the router’s LAN IP address)
•
Primary DNS server (if you entered a primary DNS address in the Internet Setup screen;
otherwise, the router’s LAN IP address)
•
Secondary DNS server (if you entered a secondary DNS address in the Internet Setup
screen)
You can use another device on your network as the DHCP server, or specify the network
settings of all of your computers.
NETGEAR genie Advanced Home
37
R6200v2 Smart WiFi Router

To disable the DHCP server feature in the router:
1. Select Advanced > Setup > LAN Setup.
2. Clear the Use Router as DHCP Server check box.
3. Click Apply.
4. (Optional) If this service is disabled and no other DHCP server is on your network, set your
computer IP addresses manually so that they can access the router.
Set Up Address Reservation
When you specify a reserved IP address for a computer on the LAN, that computer always
receives the same IP address each time it accesses the router’s DHCP server. Assign
reserved IP addresses to computers or servers that require permanent IP settings.

To reserve an IP address:
1. Select Advanced > Setup > LAN Setup.
2. In the Address Reservation section of the screen, click the Add button.
3. In the IP Address field, type the IP address to assign to the computer or server.
Choose an IP address from the router’s LAN subnet, such as 192.168.1.x.
4. Type the MAC address of the computer or server.
Tip: If the computer is already on your network, you can copy its MAC
address from the Attached Devices screen and paste it here.
5. Click Apply.
The reserved address is entered into the table.
The reserved address is not assigned until the next time the computer contacts the router’s
DHCP server. Reboot the computer, or access its IP configuration and force a DHCP release
and renew.

To edit or delete a reserved address entry:
1. Select the radio button next to the reserved address you want to edit or delete.
2. Click Edit or Delete.
WPS Wizard for WiFi Connections
The WPS Wizard helps you add a wireless computer or device to your WiFi network without
typing the WiFi password.

To use the WPS Wizard:
1. Select Advanced > WPS Wizard.
NETGEAR genie Advanced Home
38
R6200v2 Smart WiFi Router
2. Click Next.
3. Select the radio button for the setup method that you want to use.
• Push button. Either click the WPS button on this screen, or press the WPS button on
the side of the router. Within 2 minutes, go to the wireless client and press its WPS
button to join the network without entering a password.
•
PIN Number. The screen adjusts.
Enter the client security PIN, and click Next
4. Within 2 minutes, go to the client device and use its WPS software to join the network
without entering a password.
The WPS process automatically sets up your wireless computer with the network
password and connects it to the wireless network. The router WPS screen displays a
confirmation message.
Quality of Service (QoS) Setup
QoS is an advanced feature that can be used to prioritize some types of traffic ahead of
others. The router can provide QoS prioritization over the wireless link and on the Internet
connection.
WMM QoS for Wireless Multimedia Applications
The router supports Wi-Fi Multimedia Quality of Service (WMM QoS) to prioritize wireless
voice and video traffic over the wireless link. WMM QoS provides prioritization of wireless
data packets from different applications based on four access categories: voice, video, best
effort, and background. For an application to receive the benefits of WMM QoS, both it and
the client running that application have to have WMM enabled. Legacy applications that do
not support WMM and applications that do not require QoS, are assigned to the best effort
NETGEAR genie Advanced Home
39
R6200v2 Smart WiFi Router
category, which receives a lower priority than voice and video. WMM QoS is enabled by
default.

To disable WMM QoS:
1. Select Advanced > Setup > QoS Setup.
2. Clear the Enable WMM check box for the band (2.4 GHz or 5 GHz).
3. Click Apply.
Set Up Bandwidth Control

To set up the maximum uplink bandwidth:
1. Select Advanced > Setup > QoS Setup.
2. Leave the Enable WMM check boxes selected.
3. (Optional) To prioritize Internet traffic, select the Turn Internet Access QoS On check box.
4. (Optional) To detect the current uplink bandwicth, click the Check button.
This helps you to determinate the maximum bandwidth setting
5. Select the Turn Bandwidth Control On check box.
6. Use one of these methods to specify the maximum bandwidth:
• To use the current uplink bandwidth, select the Uplink bandwidth radio button.
•
Select the Automatically check Internet uplink bandwidth radio button.
7. Click Apply.
NETGEAR genie Advanced Home
40
R6200v2 Smart WiFi Router
Set Up QoS for Internet Access
You can give prioritized Internet access to the following types of traffic:
•
Specific applications
•
Specific online games
•
Individual Ethernet LAN ports of the router
•
A specific device by MAC address
To specify prioritization of traffic, create a policy for the type of traffic and add the policy to the
QoS Policy table in the QoS Setup screen. For convenience, the QoS Policy table lists many
common applications and online games that can benefit from QoS handling.
QoS for Applications and Online Gaming

To create a QoS policy for applications and online games:
1. Select Advanced > Setup > QoS Setup.
2. Select the Turn Internet Access QoS On check box.
3. Click the Setup QoS rule button.
The QoS Priority Rule list displays.
NETGEAR genie Advanced Home
41
R6200v2 Smart WiFi Router
4. To add a priority rule, scroll down to the bottom of the QoS Setup screen and click Add
Priority Rule.
5. In the QoS Policy for field, type the name of the application or game.
6. In the Priority Category list, select either Applications or Online Gaming.
A list of applications or games displays.
7. Scroll and select Add a New Application, or Add a New Game, as applicable.
8. If prompted, in the Connection Type list, select either TCP, UDP, or both (TCP/UDP). Specify
the port number or range of port numbers that the application or game uses.
9. From the Priority list, select the priority for Internet access for this traffic relative to other
applications and traffic. The options are Low, Normal, High, and Highest.
10. Click Apply.
The rule is saved in the QoS Policy list.
The QoS Setup screen displays.
QoS for a Router LAN Port

To create a QoS policy for a device connected to one of the router’s LAN ports:
1. Select Advanced > Setup > QoS Setup.
2. Select the Turn Internet Access QoS On check box.
3. Click the Setup QoS Rule button.
4. Click the Add Priority Rule button.
5. From the Priority Category list, select Ethernet LAN Port.
6. From the QoS Policy for list, select the LAN port.
NETGEAR genie Advanced Home
42
R6200v2 Smart WiFi Router
7. From the Priority list, select the priority for Internet access for this port’s traffic relative to
other applications. The options are Low, Normal, High, and Highest.
8. Click Apply.
The rule is saved in the QoS Policy list.
The QoS Setup screen displays.
9. Click Apply.
QoS for a MAC Address

To create a QoS policy for traffic from a specific MAC address:
1. Select Advanced > Setup > QoS Setup, and click the Setup QoS Rule button.
The QoS Setup screen displays.
2. Click Add Priority Rule.
3. From the Priority Category list, select MAC Address.
4. If the device to be prioritized appears in the MAC Device List, select its radio button.
The information from the MAC Device List populates the policy name, MAC Address, and
Device Name fields. If the device does not appear in the MAC Device List, click Refresh.
If it still does not appear, fill in these fields manually.
5. From the Priority list, select the priority for Internet access for this device’s traffic relative to
other applications and traffic. The options are Low, Normal, High, and Highest.
6. Click Apply.
This rule is saved in the QoS Policy list.
The QoS Setup screen displays.
7. Select the Turn Internet Access QoS On check box.
8. Click Apply.
NETGEAR genie Advanced Home
43
R6200v2 Smart WiFi Router
Edit or Delete an Existing QoS Policy

To edit or delete a QoS policy:
1. Select Advanced > QoS Setup.
2. Select the radio button next to the QoS policy that you want to edit or delete, and do one of
the following:
• Click Delete to remove the QoS policy.
•
Click Edit to edit the QoS policy and change the policy settings.
3. Click Apply.
Your changes are saved in the QoS Setup screen.
NETGEAR genie Advanced Home
44
5.
USB Storage
A ccessing an d Co nfig ur ing a USB St or age
Device
This chapter describes how to access and configure a USB storage drive attached to your router.
The USB port on the router can be used only to connect USB storage devices like flash drives or
hard drives, or a printer. Do not connect computers, USB modems, CD drives, or DVD drives to
the router USB port.
This chapter contains the following sections:
•
Connect a USB Storage Device to the Router
•
Safely Remove a USB Drive
•
Access the USB Storage Device
•
Sharing Files
•
View a USB Device Attached to the Router
•
USB Storage Device Network and Access Settings
•
Available Network Folders
•
Specify Approved USB Devices
•
Media Server Settings
•
TiVo Support
For information about using the ReadySHARE Printer feature, see Chapter 6, ReadySHARE
Printer.
For more about ReadySHARE features, visit www.netgear.com/readyshare.
45
R6200v2 Smart WiFi Router
Connect a USB Storage Device to the Router
ReadySHARE lets you access and share or a USB drive connected the router USB port. If
your USB device has special drivers, it is not compatible.

To connect a USB storage device:
1. Insert your USB storage device into the USB port on the rear panel of the router.
2. If your USB device has a power supply, you must use it when you connect the USB device
to the router.
It might take up to 2 minutes before the USB device is ready for sharing.
Safely Remove a USB Drive
If you want to physically disconnect a USB drive from the router USB port, first, log in to the
router, and then safely remove it.

To remove a USB disk drive safely:
1. Select USB Storage > Basic Settings.
2. Click the Safely Remove USB Device button.
This takes the drive offline.
3. Physically disconnect the USB drive.
Access the USB Storage Device
When you connect the USB device to the router USB port, it might take up to 2 minutes
before it is ready for sharing. By default, the USB storage device is available to all computers
on your local area network (LAN).

To access the USB device from a Mac:
1. Select Go > Connect to Server.
2. Enter smb://readyshare as the server address.
3. Click Connect.
USB Storage
46
R6200v2 Smart WiFi Router

To access the USB device from a Windows computer:
Use any of these methods to access the USB device:

•
Select Start > Run. Enter \\readyshare in the dialog box and click OK.
•
Open a browser and enter \\readyshare in the address bar.
•
Open My Network Places and enter \\readyshare in the address bar.
To map the USB device to a Windows network drive:
1. Visit www.netgear.com/readyshare.
2. In the ReadySHARE USB Storage Access pane, click PC Utility.
The readyshareconnect.exe file is downloaded to your computer.
3. Launch readyshareconnect.exe.
4. Select the drive letter to map to the network folder.
5. (Optional) If you want to connect to the USB drive as a different user, select the Connect
using different credentials check box.
a. Type the user name and password that you want to use.
b. Click OK.
6. Click Finish.
The USB drive is mapped to the drive letter that you specified.

To access the USB drive from a remote computer:
1. Launch a web browser.
2. Connect using the router’s Internet port IP address.
If you are using Dynamic DNS, you can type the DNS name, rather than the IP address.
You can view the router’s Internet IP address on the Basic Home screen (see Dashboard
(Basic Home Screen) on page 16).
USB Storage
47
R6200v2 Smart WiFi Router

To access the USB drive with FTP from a remote computer:
1. Make sure that the FTP check box is selected in the Access Method section of the USB
Storage (Advanced Settings) screen (see USB Storage Device Network and Access
Settings on page 51).
2. Launch a web browser.
3. Type ftp:// and the Internet port IP address in the address field of the browser.
For example, type ftp://10.1.65.4.
If you are using Dynamic DNS, you can type the DNS name rather than the IP address.
4. Type the account name and password for the account that has access rights to the USB
drive.
The user name (account name) for All – no password is guest.
The directories of the USB drive that your account has access to display. For example,
you could see: share/partition1/directory1. You can now read and copy files from the USB
directory.
Sharing Files
You can share files on the USB drive for a wide variety of business and recreational
purposes. The files can be any Windows, Mac, or Linux file type including text, Word,
PowerPoint, Excel, MP3, pictures, and multimedia files. USB drive applications include:
•
Sharing multimedia with friends and family such as MP3 files, pictures, and other
multimedia with local and remote users.
•
Sharing resources on your network. You can store files in a central location so that you do
not have to power up a computer to perform local sharing. In addition, you can share files
between Macintosh, Linux, and Windows computers by using the USB drive as a
go-between across the systems.
•
Sharing files such as Word documents, PowerPoint presentations, and text files with
remote users.
A few common uses are described in the following sections.
Share Photos
You can create your own central storage location for photos and multimedia. This method
eliminates the need to log in to (and pay for) an external photo-sharing site.

To share files with your friends and family:
1. Insert your USB drive into the USB port on the router either directly or with a USB cable.
Computers on your local area network (LAN) can automatically access this USB drive
using a web browser or Microsoft Networking.
USB Storage
48
R6200v2 Smart WiFi Router
2. If you want to specify read-only access or to allow access from the Internet, see USB
Storage Device Network and Access Settings on page 51.
Store Files in a Central Location for Printing
This scenario is for a family that has one high-quality color printer directly attached to a
computer, but not shared on the local area network (LAN). This family does not have a print
server.

•
One family member has photos on a Macintosh computer that she wants to print.
•
The photo-capable color printer is directly attached to a Windows PC, but not shared on
the network.
•
The Mac and the Windows PC are not visible to each other on the network.
To print photos from a Mac on the printer attached to a Windows PC:
•
On a Mac, access the USB drive by typing \\readyshare in the address field of a web
browser. Then copy the photos to the USB drive.
•
On a Window computer, use a web browser or Microsoft Networking to copy the files from
the USB drive to the computer. Then print the files.
Share Large Files over the Internet
Sending files that are larger than 5 MB can pose a problem for many email systems. The
router allows you to share large files such as PowerPoint presentations or .zip files over the
Internet. FTP can be used to download shared files from the router.
Sharing files with a remote colleague involves the following considerations:
•
There are two user accounts: admin and guest. The password for admin is the same one
that you use to access the router. By default, it is password. The guest user account has
no password.
•
On the FTP site, the person receiving the files uses the guest user account and enters
the password. (FTP requires that you type something in the password field.)
•
Be sure to select the FTP (via Internet) check box in the USB Storage (Advanced
Settings) screen. This option supports both downloading and uploading of files.
Note: You can enable the HTTP (via Internet) option on the USB Storage
(Advanced Settings) screen to share large files. This option supports
downloading files only.
USB Storage
49
R6200v2 Smart WiFi Router
View a USB Device Attached to the Router

To view basic information about the USB storage device:
1. Select Basic > ReadySHARE.
By default, the Basic radio button is selected, and the screen displays a USB storage
device if it is attached to the router USB port.
If you logged in to the router before you connected your USB device, you might not see
your USB device in this screen. If this happens, log out and then log back in.
2. (Optional) To view the files and folders on the USB device, click the network device name or
the share name.
3. (Optional) To view more detail or to change the USB device settings, click Edit.
The USB Storage (Advanced Settings) screen displays. See USB Storage Device
Network and Access Settings on page 51.
USB Storage
50
R6200v2 Smart WiFi Router
USB Storage Device Network and Access Settings
You can set up the device name, workgroups, and network folders for your USB device.

To view or change the USB storage advanced settings:
1. Select Advanced > USB Storage > Advanced Settings.
2. Specify access to the USB storage device.
• Network Device Name. The default is readyshare. This is the name used to access
the USB device connected to the router.
•
Workgroup. If you are using a Windows workgroup rather than a domain, the
workgroup name is displayed here. The name works only in an operating system that
supports NetBIOS, such as Microsoft Windows.
•
Access Method. Select the check boxes for the access methods that you want.
Network Neighborhood/MacShare. Enabled by default.
HTTP. Enabled by default. You can type
http://readyshare.routerlogin.net/shares to access the USB drive.
HTTP (via Internet). Disabled by default. If you enable this feature, remote users
can type http:// (for example,
http://1.1.10.102/shares) or a URL domain name to access the USB drive over the
Internet. This feature supports file uploading only.
FTP. Disabled by default.
FTP (via Internet). Disabled by default. If you select this feature, remote users
can access the USB drive through FTP over the Internet. This feature supports
both downloading and uploading of files.
3. If you changed the settings, click Apply.
Your changes are saved.
USB Storage
51
R6200v2 Smart WiFi Router
Available Network Folders
You can view or change the network folders on the USB storage device.

To view network folders:
1. Select Advanced > USB Storage > Advanced Settings.
2. Scroll down to the Available Networks Folder section of the screen.
• Share Name. If only one device is connected, the default share name is
USB_Storage. (Some router models have more than one USB port.)
You can click the name, or you can type it in the address field of your web browser. If
Not Shared is shown, the default share has been deleted, and no other share for the
root folder exists. Click the link to change this setting.

•
Read Access and Write Access. Show the permissions and access controls on the
network folder: All–no password (the default) allows all users to access the network
folder. The password for admin is the same one that you use to log in to the router.
•
Folder Name. Full path of the network folder.
•
Volume Name. Volume name from the storage device (either USB drive or HDD).
•
Total Space and Free Space. Show the current utilization of the storage device.
To add a network folder:
1. Select Advanced > ReadySHARE.
2. Click Edit.
USB Storage
52
R6200v2 Smart WiFi Router
3. Click Create Network Folder.
If the Add a Network Folder screen does not display, your web browser might be blocking
pop-ups. If it is, change the browser settings to allow pop-ups.
4. In the Folder field, browse and select the folder.
5. Fill in the Share Name field.
6. In the Read Access list and the Write Access list, select the setting that you want.
The user name (account name) for All – no password is guest. The password for admin is
the same one that is used to log in to the router. By default, it is password.
7. Click Apply.
The folder is added on the USB device.

To edit a network folder:
1. Select Advanced > ReadySHARE.
2. Click the Edit button.
The Edit Network Folder screen displays the same settings shown in the Add a Network
Folder screen.
3. Change the settings in the fields as needed.
4. Click Apply.
Your changes are saved.
USB Storage
53
R6200v2 Smart WiFi Router
Specify Approved USB Devices
For more security, you can set up the router to share only approved USB devices.

To set up approved USB devices:
1. Select Advanced > Advanced Setup > USB Settings.
2. Click the Approved Devices button.
This screen shows the approved USB devices and the available USB devices. You can
remove or add approved USB devices.
3. In the Available USB Devices list, select the drive that you want to approve.
4. Click Add.
5. Select the Allow only approved devices check box.
6. Click Apply.
Your change takes effect.
If you want to work with another USB device, first click the Safely Remove USB Device
button for the currently connected USB device. Connect the other USB device, and repeat
this process.
USB Storage
54
R6200v2 Smart WiFi Router
Media Server Settings
By default, the router acts as a ReadyDLNA media server, which lets you view movies and
photos on DLNA/UPnP AV-compliant media players, such as Xbox360, Playstation, and
NETGEAR media players.
ReadyDLNA implies this device serves media in DLNA compatible form to DLNA/UPnP
AV-compliant media players.

To view these settings:
Select Advanced > USB Storage > Media Server.
By default, the Enable Media Server check box and the Automatic (when new files are
added) radio button are selected. When these options are selected, the router scans for
media files whenever new files are added to the ReadySHARE USB hard drive.
Enable Media Server. Select this check box to enable this device to act as a media server.
Enable TiVo support. Select this check box if you want to play ReadyNAS media on your
TiVo device. See the following section.
Media Server Name. Specify the name of the media server.
Automatic (when new files added). Automatically scans for media files whenever new files
are added to the ReadySHARE USB storage. Only shared folders with “All – no password” in
read access can be scanned for media files.
TiVo Support
You can set up your TiVo to access media files stored on a USB device that is connected to
your router. The TiVo must be on the same network as the router. This feature supports the
following file formats:
•
Video. See and play mpeg1, and mpeg2 files.
•
Music. See and play MP3 files.
•
Pictures. View images in jpg format.
USB Storage
55
R6200v2 Smart WiFi Router
Use ReadyDLNA to Play Media from Your Network on TiVo
You can use the TiVo (Series 2 and up) Home Media Option to play photos and music on your
PC or Mac right in your TiVo user interface.

To set up the router to work with TiVo:
1. Select Advanced > USB Storage > Media Server.
2. Make sure that the Enable TiVo support check box is selected.

To play videos:
1. On the TiVo, select TiVo Central > My Shows.
2. Go to the bottom of the list to find and select the R6200v2.
FOR POSITION ONLY
USB Storage
56
R6200v2 Smart WiFi Router

To play music or view photos:
1. On the TiVo, select TiVo Central > Music, Photos, & Showcases.
2. Select what you want to play or watch.
FOR POSITION ONLY

To copy TiVo Files onto a computer:
Use the TiVo Desktop accessory available at
https://www3.tivo.com/store/accessories-software.do.
USB Storage
57
6.
ReadySHARE Printer
S etting up a nd ma na ging a s har ed USB pr int er
ReadySHARE Printer is compatible with Macs and Windows computers. It lets you connect a
USB printer to the router USB port, and access it wirelessly.
This chapter contains the following sections:
•
ReadySHARE Printer Utility
•
Set Up the ReadySHARE Printer Utility
•
Install the NETGEAR USB Control Center
•
Manage USB Print and Scan Jobs
Note: The USB port on the router can connect only to USB devices like
flash drives, hard drives, and printers. Do not connect computers,
USB modems, CD drives, or DVD drives to the router USB port.
58
R6200v2 Smart WiFi Router
ReadySHARE Printer Utility
The ReadySHARE Printer utility allows you to control from your computer a shared USB
printer that is connected to the USB port on your router. You can share this USB printer
among the Windows and Mac computers on your network.
You have to install this utility before you can use the ReadySHARE Printer feature.
•
For this feature to work, this utility has to be installed and running in the background on
each computer from which you want to control this USB printer.
•
The driver software for the USB printer has to be installed on each computer from which
you want to control this USB printer.
•
The ReadySHARE Printer utility has both a Mac version and a Windows version.
•
The ReadySHARE Printer utility setup file and instructions are available through this
URL: www.netgear.com/readyshare
Once installed, the ReadySHARE Printer utility displays on your computer as the NETGEAR
USB Control Center.
Set Up the ReadySHARE Printer Utility
You have to connect the USB Printer to your router and install the utility on each computer in
your network from which you want to control the USB printer.

To set up ReadySHARE Printer:
1. Connect the USB printer to the router USB port with a USB printer cable.
Note: Some USB printers (for example, HP and Lexmark printers) request that
you do not connect the USB cable until the installation software prompts you.
2. On each computer on your network that shares the USB printer, install the driver software
for the USB printer.
If you do not have the printer driver, contact the printer manufacturer to find and download
the most recent printer driver software.
ReadySHARE Printer
59
R6200v2 Smart WiFi Router
3. Download the ReadySHARE Printer utility setup file and instructions from
www.netgear.com/readyshare
4. On each computer on your network that shares the USB printer, install the ReadySHARE
Printer utility.
Once installed, the ReadySHARE Printer utility displays on your computer as the
NETGEAR USB Control Center.
Install the NETGEAR USB Control Center
For the ReadySHARE Print feature to work, this utility has to be installed and running in the
background on each computer in the network from which you want to control this USB printer.
Once installed, the ReadySHARE Printer utility displays on your computers as the NETGEAR
USB Control Center.

To install the NETGEAR USB Control Center:
1. On each computer on your network that shares the USB printer, double-click the
ReadySHARE Printer utility setup file that you downloaded.
The ReadySHARE Printer utility setup file and instructions can be downloaded through
this URL: www.netgear.com/readyshare
2. Follow the instructions to install the NETGEAR USB Control Center utility.
ReadySHARE Printer
60
R6200v2 Smart WiFi Router
3. Select the language and click OK.
The setup file installs the utility.
4. On each computer on your network that shares the USB printer, perform the initial setup of
the NETGEAR USB Control Center.
The first time you use the USB printer that is connected to your router, you are asked to
select the USB printer. For more information, see Initial Setup of the NETGEAR USB
Control Center on page 75.
5. (Optional) Change the default settings.
For more information, see Configure the NETGEAR USB Control Center on page 77.
Set Up the NETGEAR USB Control Center
The first time you access the utility, you are asked to select the printer.

•
When a USB printer is detected and connected automatically during the initial setup, you
have to disconnect the printer and wait for the prompt asking you to click Connect.
•
You might be asked to install the driver for this printer. After the driver is installed, the
printer status changes to Available.
To set up the NETGEAR USB Control Center:
1. On each computer on your network that shares the USB printer, launch the NETGEAR
USB Control Center the same way you launch any application program on your
Windows or MAC computer.
ReadySHARE Printer
61
R6200v2 Smart WiFi Router
2. Select the printer and click the Connect button.
Once the connection is established, the status changes to Manually connected by xxx.
3. Click the Disconnect button.
The status changes to Available.
For each computer, after you click the Connect and Disconnect buttons once, the utility
automatically handles the printing queue and handling. The status of the printer appears
as Available on all the computers.
The utility does not always need to hold the connection of a USB printer. After a print job
is created for some USB printers, the NETGEAR USB Control Center connects to this
USB printer automatically and prints. After the print job is done, the printer status might
return to a Paused state.
ReadySHARE Printer
62
R6200v2 Smart WiFi Router
For example, the USB printer displayed in the Windows Printers and Faxes window is
ready for print jobs.
Configure the NETGEAR USB Control Center
You can set the time-out and specify other settings from the Configuration screen.

To configure the NETGEAR USB Control Center:
1. Launch the NETGEAR USB Control Center the same way you launch any application
program on your Windows or MAC computer.
2. Select Tools > Configuration.
3. Specify the following settings:
• Automatically execute when logging on Windows. Enable this utility to start
automatically when you are logged in to Windows.
ReadySHARE Printer
63
R6200v2 Smart WiFi Router
•
Timeout. Specify the time-out value for holding the USB resource when it is not in
use.
•
Language. Select the display language for this utility.
4. Click OK.
Your changes are saved.
Manage USB Print and Scan Jobs
The NETGEAR USB Control Center utility runs in the background on each computer in your
network. This utility manages the printing queue and handling for the USB printer connected
to your router.
After you activate the utility on each computer in the network, the status of the USB printer is
Available on all of the computers.
•
When the status is Available, you can use the USB printer from any computer in the
network. The utility on each computer automatically manages the printing queue and
handling. The status of the USB printer appears as Available on all of the computers
when no print jobs are in process.
•
When the status is Manually connected by xxx, only the xxx computer can use the printer.
Other network devices must wait until the xxx computer has released the connection, or
until the connection times out (the default time-out value is 30 seconds).
You can click the Disconnect button at any time to release the connection.
You can set the value for the default time-out time from the Configuration screen. For more
information, see Configure the NETGEAR USB Control Center.
Some firewall software, such as Comodo, blocks the NETGEAR USB Control Center utility
from accessing the USB printer. If you do not see the USB printer in the utility, you can
disable the firewall temporarily to allow the utility to work.
If your USB printer supports scanning, you can also use the USB printer for scanning. For
more information, see Use the Scan Feature of a Multifunction USB Printer on page 660.
ReadySHARE Printer
64
R6200v2 Smart WiFi Router
Launch the NETGEAR USB Control Center
The NETGEAR USB Control Center shows the availability status of the USB devices. The
NETGEAR USB Control Center utility must be running for the computer to be able to print to
the USB printer attached to the router. If you exit the utility, printing does not work.

To launch the NETGEAR USB Control Center:
Launch the NETEAR USB Control Center the same way you launch any application
program on your Windows or MAC computer.
The main screen shows a device icon, the description for this USB device, and its status.
•
Available. The device is available from the computer that you are using.
•
Waiting to Connect. You need to connect to this device from the computer that you are
using. The first time you connect, you might be prompted to install the device driver.
The following menu selections display:
•
System. Exit the utility.
•
Tools. Access the Control Center - Configuration screen to set up your shared USB
device. For more information, see Configure the NETGEAR USB Control Center on
page 63.
•
About. View details about the USB Control Center software.
The following control buttons are available:
•
Connect. The first time you access the utility, you are asked to select the printer and click
the Connect button.
•
Disconnect. Click the Disconnect button at any time to release the connection.
•
Network Scanner. This button activates the Scanner window so that you can use the
printer for scanning. Your printer must support scanning and be in the Available state.
ReadySHARE Printer
65
R6200v2 Smart WiFi Router
Use the Scan Feature of a Multifunction USB Printer
If your USB printer supports scanning, you can also use the USB printer for scanning
To use the scan feature of a multifunction USB printer:
1. Launch the NETGEAR USB Control Center the same way you launch any application
program on your Windows or MAC computer.
2. Make sure that the printer status shows as Available
3. Click the Network Scanner button.
The scanner window opens so that you can use the USB printer for scanning.
ReadySHARE Printer
66
7.
Security
C ustom izing the firew all s et t ings
This chapter explains how to use the basic firewall features of the router to prevent objectionable
content from reaching the computers and devices on your network.
This chapter includes the following sections:
•
Keyword Blocking of HTTP Traffic
•
Block Services (Port Filtering)
•
Port Triggering to Open Incoming Ports
•
Port Forwarding to Permit External Host Communications
•
How Port Forwarding Differs from Port Triggering
•
Set Up Port Forwarding to Local Servers
•
Set Up Port Triggering
•
Schedule Blocking
•
Set up Security Event Email Notifications
For information about Live Parental Controls, see Parental Controls on page 22.
67
R6200v2 Smart WiFi Router
Keyword Blocking of HTTP Traffic
Use keyword blocking to prevent certain types of HTTP traffic from accessing your network.
The blocking can be always or according to a schedule.

To set up keyword blocking:
1. Select Advanced > Security > Block Sites.
2. Select one of the keyword blocking options:
• Per Schedule. Turn on keyword blocking according to the Schedule screen settings.
(See Schedule Blocking on page 77.)
•
Always. Turn on keyword blocking all the time, independent of the Schedule screen.
3. In the Keyword field, enter a keyword or domain, click Add Keyword, and click Apply.
The Keyword list supports up to 32 entries. Here are some sample entries:

•
Specify XXX to block http://www.badstuff.com/xxx.html.
•
Specify .com if you want to allow only sites with domain suffixes such as .edu or .gov.
•
Enter a period (.) to block all Internet browsing access.
To delete a keyword or domain:
1. Select the keyword you want to delete from the list.
2. Click Delete Keyword.
3. Click Apply.
Your changes are saved.

To specify a trusted computer:
You can exempt one trusted computer from blocking and logging. The computer you exempt
has to have a fixed IP address.
1. In the Trusted IP Address field, enter the IP address.
2. Click Apply.
Security
68
R6200v2 Smart WiFi Router
Your changes are saved.
Block Services (Port Filtering)
Services are functions that server computers perform at the request of client computers. For
example, web servers serve web pages, time servers serve time and date information, and
game hosts serve data about other players’ moves. When a computer on the Internet sends
a request for service to a server computer, the requested service is identified by a service or
port number. This number appears as the destination port number in the transmitted IP
packets. For example, a packet that is sent with the destination port number 80 is an HTTP
(web server) request.
The service numbers for many common protocols are defined by the Internet Engineering
Task Force (IETF at http://www.ietf.org/) and published in RFC1700, “Assigned Numbers.”
Service numbers for other applications are typically chosen from the range 1024 - 65535 by
the authors of the application. Although the router already holds a list of many service port
numbers, you are not limited to these choices. You can often determine port number
information by contacting the publisher of the application, by asking user groups or
newsgroups, or by searching.
The Block Services screen lets you add and block specific Internet services by computers on
your network. This is called service blocking or port filtering. To add a service for blocking,
first determine which port number or range of numbers the application uses.

To block services:
1. Select Advanced > Security > Block Services.
2. Select either Per Schedule or Always.
3. If you selected Per Schedule, specify a time period in the Schedule screen.
4. Click Add to add a service.
Security
69
R6200v2 Smart WiFi Router
The Block Services Setup screen displays:
5. From the Service Type list, select the application or service to allow or block.
The list displays several common services, but you are not limited to these choices. To
add any additional services or applications that do not already appear, select User
Defined.
6. If you know that the application uses either TCP or UDP, select the appropriate protocol. If
you are not sure, select Both.
7. Enter the starting and ending port numbers.
If the application uses a single port number, enter that number in both fields.
8. Select the radio button for the IP address configuration you want to block, and enter the IP
addresses.
You can block the specified service for a single computer, a range of computers with
consecutive IP addresses, or all computers on your network.
9. Click Add.
Your changes are saved.
Port Triggering to Open Incoming Ports
Some application servers (such as FTP and IRC servers) send replies to multiple port
numbers. Using the port triggering function of your router, you can tell the router to open
more incoming ports when a particular outgoing port originates a session.
An example is Internet Relay Chat (IRC). Your computer connects to an IRC server at
destination port 6667. The IRC server not only responds to your originating source port, but
also sends an “identify” message to your computer on port 113. Using port triggering, you can
tell the router, “When you initiate a session with destination port 6667, you have to also allow
incoming traffic on port 113 to reach the originating computer.” Using steps similar to the
Security
70
R6200v2 Smart WiFi Router
preceding example, the following sequence shows the effects of the port triggering rule you
have defined:
1. You open an IRC client program to start a chat session on your computer.
2. Your IRC client composes a request message to an IRC server using a destination port
number of 6667, the standard port number for an IRC server process. Your computer then
sends this request message to your router.
3. Your router creates an entry in its internal session table describing this communication
session between your computer and the IRC server. Your router stores the original
information, performs Network Address Translation (NAT) on the source address and port,
and sends this request message through the Internet to the IRC server.
4. Noting your port triggering rule and having observed the destination port number of 6667,
your router creates an additional session entry to send any incoming port 113 traffic to your
computer.
5. The IRC server sends a return message to your router using the NAT-assigned source port
(for example, port 33333) as the destination port. The IRC server also sends an “identify”
message to your router with destination port 113.
6. Upon receiving the incoming message to destination port 33333, your router checks its
session table to determine whether there is an active session for port number 33333.
Finding an active session, the router restores the original address information replaced by
NAT and sends this reply message to your computer.
7. Upon receiving the incoming message to destination port 113 your router checks its session
table and learns that there is an active session for port 113, associated with your computer.
The router replaces the message’s destination IP address with your computer’s IP address
and forwards the message to your computer.
8. When you finish your chat session, your router eventually senses a period of inactivity in the
communications. The router then removes the session information from its session table,
and incoming traffic is no longer accepted on port numbers 33333 or 113.
To configure port triggering, you need to know which inbound ports the application needs.
Also, you need to know the number of the outbound port that will trigger the opening of the
inbound ports. You can usually determine this information by contacting the publisher of the
application or the relevant user groups or news groups.
Only one computer at a time can use the triggered application.
Port Forwarding to Permit External Host
Communications
In both of the preceding examples, your computer initiates an application session with a
server computer on the Internet. However, you might need to allow a client computer on the
Internet to initiate a connection to a server computer on your network. Normally, your router
ignores any inbound traffic that is not a response to your own outbound traffic. You can
configure exceptions to this default rule by using the port forwarding feature.
A typical application of port forwarding can be shown by reversing the client-server
relationship from the previous web server example. In this case, a remote computer’s
Security
71
R6200v2 Smart WiFi Router
browser needs to access a web server running on a computer in your local network. Using
port forwarding, you can tell the router, “When you receive incoming traffic on port 80 (the
standard port number for a web server process), forward it to the local computer at
192.168.1.123.” The following sequence shows the effects of the port forwarding rule you
have defined:
1. The user of a remote computer opens a browser and requests a web page from
www.example.com, which resolves to the public IP address of your router. The remote
computer composes a web page request message with the following destination
information:
Destination address. The IP address of www.example.com, which is the address of your
router.
Destination port number. 80, which is the standard port number for a web server
process.
The remote computer then sends this request message through the Internet to your
router.
2. Your router receives the request message and looks in its rules table for any rules covering
the disposition of incoming port 80 traffic. Your port forwarding rule specifies that incoming
port 80 traffic should be forwarded to local IP address 192.168.1.123. Therefore, your router
modifies the destination information in the request message:
The destination address is replaced with 192.168.1.123.
Your router then sends this request message to your local network.
3. Your web server at 192.168.1.123 receives the request and composes a return message
with the requested web page data. Your web server then sends this reply message to your
router.
4. Your router performs Network Address Translation (NAT) on the source IP address, and
sends this request message through the Internet to the remote computer, which displays the
web page from www.example.com.
To configure port forwarding, you need to know which inbound ports the application needs.
You usually can determine this information by contacting the publisher of the application or
the relevant user groups or news groups.
How Port Forwarding Differs from Port Triggering
The following points summarize the differences between port forwarding and port triggering:
•
Any computer on your network can use port triggering, although only one computer can
use it at a time.
•
Port forwarding is configured for a single computer on your network.
•
With port triggering, the router does not need to know the computer’s IP address in
advance. The IP address is captured automatically.
•
Port forwarding requires that you specify the computer’s IP address during configuration,
and the IP address can never change.
Security
72
R6200v2 Smart WiFi Router
•
Port triggering requires specific outbound traffic to open the inbound ports, and the
triggered ports are closed after a period of no activity.
•
Port forwarding is always active and does not need to be triggered.
Set Up Port Forwarding to Local Servers
The port forwarding feature lets you allow certain types of incoming traffic to reach servers on
your local network. For example, you might want to make a local web server, FTP server, or
game server visible and available to the Internet.
Use the Port Forwarding/Port Triggering screen to configure the router to forward specific
incoming protocols to computers on your local network. In addition to servers for specific
applications, you can also specify a default DMZ server to which all other incoming protocols
are forwarded.
Before you start, determine which type of service, application, or game you want to provide,
and the local IP address of the computer that will provide the service. The server computer
has to always have the same IP address.
To ensure that your server computer always has the same IP address, use the reserved IP
address feature of your product. See Set Up Address Reservation on page 38.

To forward specific incoming protocols:
1. Select Advanced > Advanced Setup > Port Forwarding/Port Triggering.
2. Leave the Port Forwarding radio button selected as the service type.
3. In the Service Name list, select the service name.
4. Click the Add button.
A list of services display. If the service that you want to add is not in the list, see Add a
Custom Service on page 74.
5. Fill in the Server IP Address field
6. Click Add.
The service appears in the list on the Port Forwarding screen.
Security
73
R6200v2 Smart WiFi Router
Add a Custom Service
To define a service, game, or application that does not appear in the Service Name list, first
determine which port number or range of numbers the application uses. You can usually
determine this information by contacting the publisher of the application or user groups or
news groups. When you have the port number information, follow these steps.

To add a custom service:
1. Select Advanced > Advanced Setup > Port Forwarding/Port Triggering.
2. Select the Port Forwarding radio button as the service type.
3. Click the Add Custom Service button.
4. In the Service Name field, enter a descriptive name.
5. In the Service Type field, select the protocol. If you are unsure, select TCP/UDP.
6. In the External Starting Port field, enter the beginning port number.
• If the application uses a single port, enter the same port number in the Ending Port
field.
•
If the application uses a range of ports, enter the ending port number of the range in
the External Ending Port field.
7. Specify the internal ports by one of these methods:
• Leave the Use the same port range for Internal port check box selected.
•
Fill in the Internal Starting Port and Internal Ending Port fields.
8. Fill in the Internal IP address field, or select the radio button for an attached device listed in
the table.
9. Click Apply.
The service appears in the list in the Port Forwarding/Port Triggering screen.
Security
74
R6200v2 Smart WiFi Router
Edit or Delete a Port Forwarding Entry

To edit or delete a port forwarding entry:
1. Select Advanced > Advanced Setup > Port Forwarding/Port Triggering.
2. Select the Port Forwarding radio button as the service type
3. In the table, select the radio button next to the service name.
4. Click Edit Service or Delete Service.
Application Example: Make a Local Web Server Public
If you host a web server on your local network, you can use port forwarding to allow web
requests from anyone on the Internet to reach your web server.

To make a local web server public:
1. Assign your web server either a fixed IP address or a dynamic IP address using DHCP
address reservation.
In this example, your router always gives your web server an IP address of 192.168.1.33.
2. In the Port Forwarding/Port Triggering screen, configure the router to forward the HTTP
service to the local address of your web server at 192.168.1.33.
HTTP (port 80) is the standard protocol for web servers.
3. (Optional) Register a host name with a Dynamic DNS service, and configure your router to
use the name.
To access your web server from the Internet, a remote user has to know the IP address
that your ISP assigned. However, if you use a Dynamic DNS service, the remote user can
reach your server by a user-friendly Internet name, such as mynetgear.dyndns.org.
Set Up Port Triggering
Port triggering is a dynamic extension of port forwarding that is useful in these cases:
•
More than one local computer needs port forwarding for the same application (but not
simultaneously).
•
An application needs to open incoming ports that are different from the outgoing port.
When port triggering is enabled, the router monitors outbound traffic looking for a specified
outbound “trigger” port. When the router detects outbound traffic on that port, it remembers
the IP address of the local computer that sent the data. The router then temporarily opens the
specified incoming port or ports and forwards incoming traffic on the triggered ports to the
triggering computer.
Port forwarding creates a static mapping of a port number or range to a single local computer.
Port triggering can dynamically open ports to any computer that needs them and can close
the ports when they are no longer needed.
Security
75
R6200v2 Smart WiFi Router
Note: If you use applications such as multiplayer gaming, peer-to-peer
connections, real-time communications such as instant messaging,
or remote assistance (a feature in Windows XP), you should also
enable Universal Plug and Play (UPnP). See Universal Plug and
Play on page 105.
To configure port triggering, you need to know which inbound ports the application needs,
and the number of the outbound port that will trigger the opening of the inbound ports. You
can usually determine this information by contacting the publisher of the application or user
groups or news groups.

To enable port triggering:
1. Select Advanced > Advanced Setup > Port Forwarding/Port Triggering.
2. Select the Port Triggering radio button.
3. Clear the Disable Port Triggering check box.
Note: If the Disable Port Triggering check box is selected after you
configure port triggering, port triggering is disabled. However, any
port triggering configuration information you added to the router is
retained even though it is not used.
4. In the Port Triggering Timeout field, enter a value up to 9999 minutes.
This value controls the inactivity timer for the designated inbound ports. The inbound
ports close when the inactivity time expires. This is required because the router cannot be
sure when the application has terminated.
Security
76
R6200v2 Smart WiFi Router

To add a port triggering service:
1. On the Port Triggering screen, click Add Service.
2. In the Service Name field, type a descriptive service name.
3. In the Service User list, select Any, or select Single address and enter the IP address of
one computer.
• Any (the default), allows any computer on the Internet to use this service.
•
Single address restricts the service to a particular computer.
4. Select the service type, either TCP or UDP or both (TCP/UDP). If you are not sure, select
TCP/UDP.
5. In the Triggering Port field, enter the number of the outbound traffic port that will cause the
inbound ports to be opened.
6. Enter the inbound connection port information in the Connection Type, Starting Port, and
Ending Port fields.
7. Click Apply.
The service appears in the Port Triggering Portmap table.
8. Make sure that you enable port triggering so that the service that you added will be used.
Schedule Blocking
You can specify the days and time that you want to block Internet access.
Security
77
R6200v2 Smart WiFi Router

To schedule blocking:
1. Select Advanced > Security > Schedule.
2. Set up the schedule for blocking keywords and services.
• Days to Block. Select days on which you want to apply blocking by selecting the
appropriate check boxes, or select Every Day to select the check boxes for all days.
•
Time of Day to Block. Select a start and end time in 24-hour format, or select All
Day for 24-hour blocking.
3. Select your time zone from the list. If you use daylight savings time, select the
Automatically adjust for daylight savings time check box.
4. Click Apply.
Your settings are saved.
Set up Security Event Email Notifications
To receive logs and alerts by email, provide your email information in the E-mail screen, and
specify which alerts you want to receive and how often.
Security
78
R6200v2 Smart WiFi Router

To set up email notifications:
1. Select Advanced > Security > E-mail.
2. Select the Turn Email Notification On check box.
3. In the Your Outgoing Mail Server field, enter the name of your ISP’s outgoing (SMTP) mail
server (such as mail.myISP.com).
You might be able to find this information in the configuration screen of your email
program. If you leave this field blank, log and alert messages are not sent.
4. Enter the email address to which logs and alerts are sent in the Send to This Email Address
field.
This email address is also used for the From address. If you leave this field blank, log and
alert messages are not sent.
5. If your outgoing email server requires authentication, select the My Mail Server requires
authentication check box. Fill in the User Name and Password fields for the outgoing email
server.
6. (Optional) Select the Send Alerts Immediately check box.
Email alerts are sent immediately when someone attempts to visit a blocked site.
7. (Optional) Fill in the fields in the Send logs according to this schedule section of the screen.
Logs are sent automatically. If the log fills up before the specified time, the log is emailed.
After the log is sent, the log is cleared from the router memory. If the router cannot email
the log file, the log buffer might fill up. In this case, the router overwrites the log and
discards its contents.
8. Click Apply.
Your settings are saved.
Security
79
8.
Administration
Managing yo ur n etwo r k
This chapter describes the router settings for administering and maintaining your router and
home network.
This chapter includes the following sections:
•
Upgrade the Router Firmware
•
View Router Status
•
View Logs of Web Access or Attempted Web Access
•
Manage the Configuration File
•
Change the Password
•
Password Recovery
For information about upgrading or checking the status of your router over the Internet, see
Remote Management on page 104. For information about monitoring Internet traffic, see Traffic
Meter on page 115.
80
R6200v2 Smart WiFi Router
Upgrade the Router Firmware
The router firmware (routing software) is stored in flash memory. You can update the
firmware from the Administration menu on the Advanced tab. You might see a message at
the top of the genie screens when new firmware is available for your product.
You can use the Check button on the Router Update screen to check if new firmware is
available, and to update your product.

To check for new firmware and update your router:
1. Select Advanced > Administration > Router Update.
Click
Check
2. Click Check.
The router finds new firmware information if any is available.
3. Click Yes.
The router locates an downloads the firmware and begins the update.
WARNING:
To avoid the risk of corrupting the firmware, do not interrupt the
upgrade. For example, do not close the browser, click a link, or
load a new page. Do not turn off the router..
When the upload is complete, your router restarts. The upgrade process typically takes
about 1 minute. Read the new firmware release notes to find out if you need to
reconfigure the router after upgrading.
Administration
81
R6200v2 Smart WiFi Router
View Router Status

To view router status and usage information:
Select Advanced Home or select Administration > Router Status.
FOR POSITION ONLY
Router Information
Hardware Version. The router model.
Firmware Version. The version of the router firmware. It changes if you upgrade the router
firmware.
GUI Language Version. The localized language of the user interface.
LAN Port.
•
MAC Address. The Media Access Control address. This is the unique physical address
used by the Ethernet (LAN) port of the router.
•
IP Address. The IP address used by the Ethernet (LAN) port of the router. The default is
192.168.1.1.
•
DHCP. Identifies whether the router’s built-in DHCP server is active for devices on the
LAN.
Internet Port
MAC Address. The Media Access Control address, which is the unique physical address
used by the Internet (WAN) port of the router.
IP Address. The IP address used by the Internet (WAN) port of the router. If no address is
shown or the address is 0.0.0, the router cannot connect to the Internet.
Administration
82
R6200v2 Smart WiFi Router
Connection. This shows if the router is using a fixed IP address on the WAN. If the value is
DHCP Client, the router obtains an IP address dynamically from the ISP.
IP Subnet Mask. The IP subnet mask used by the Internet (WAN) port of the router.
Domain Name Server. The Domain Name Server addresses used by the router. A Domain
Name Server translates human-language URLs such as www.netgear.com into IP
addresses.
Show Statistics Button

To view statistics:
1. Select Advanced Home or select Administration > Router Status.
2. In the Internet Port pane, click the Show Statistics button.
FOR POSITION ONLY
The following information is displayed:
System Up Time. The time elapsed since the router was last restarted.
Port. The statistics for the WAN (Internet) and LAN (Ethernet) ports. For each port, the
screen displays:
•
Status. The link status of the port.
•
TxPkts. The number of packets transmitted on this port since reset or manual clear.
•
RxPkts. The number of packets received on this port since reset or manual clear.
•
Collisions. The number of collisions on this port since reset or manual clear.
•
Tx B/s. The current transmission (outbound) bandwidth used on the WAN and LAN
ports.
•
Rx B/s. The current reception (inbound) bandwidth used on the WAN and LAN ports.
•
Up Time. The time elapsed since this port acquired the link.
•
Poll Interval. The interval at which the statistics are updated in this screen.
To change the polling frequency, enter a time in seconds in the Poll Interval field and click
Set Interval.
To stop the polling entirely, click Stop.
Administration
83
R6200v2 Smart WiFi Router
Connection Status Button

To view the Internet connection status:
1. Select Advanced Home or select Administration > Router Status.
2. In the Internet Port pane, click the Connection Status button.
FOR POSITION ONLY
The following information displays:
•
IP Address. The IP address that is assigned to the router.
•
Subnet Mask. The subnet mask that is assigned to the router.
•
Default Gateway. The IP address for the default gateway that the router
communicates with.
•
DHCP Server. The IP address for the Dynamic Host Configuration Protocol server
that provides the TCP/IP configuration for all the computers that are connected to the
router.
•
DNS Server. The IP address of the Domain Name Service server that provides
translation of network names to IP addresses.
•
Lease Obtained. The date and time when the lease was obtained.
•
Lease Expires. The date and time that the lease expires.
Click the Release button to return the status of all items to 0.
Click the Renew button to refreshes the items.
Click the Close Window button to close the Connection Status screen.
Administration
84
R6200v2 Smart WiFi Router
Wireless Settings (2.4 GHz and 5 GHz)
The following settings are displayed:
FOR POSITION ONLY
Name (SSID). The wireless network name (SSID) that the router uses.
Region. The geographic region where the router is being used. It might be illegal to use the
wireless features of the router in some parts of the world.
Channel. The operating channel of the wireless port being used. The default channel is Auto.
When Auto is selected, the router finds the best operating channel available. Channels 1, 6,
and 11 do not interfere with each other.
Mode. The wireless communication mode. At 2.4 GHz, 300 Mbps, 145 Mbps, or Up to 54
Mbps. At 5GHz 867 Mbps, 400 Mbps, or Up to 173 Mbps.
Wireless AP. Indicates whether the radio feature of the router is enabled. If this feature is not
enabled, the WiFi LED on the front panel is off.
Broadcast Name. Indicates whether the router is broadcasting its SSID.
Wireless Isolation. Wireless isolation prevents wireless clients from communicating with
each other when they join the wireless network.
Wi-Fi Protected Setup. Indicates whether WPS is configured for this network.
Administration
85
R6200v2 Smart WiFi Router
View Logs of Web Access or Attempted Web Access
The log is a detailed record of the websites you have accessed or attempted to access. Up to
256 entries are stored in the log. Log entries appear only when keyword blocking is enabled
and no log entries are made for the trusted user.

To view logs:
Select Advanced > Administration > Logs.
FOR POSITION ONLY
The log screen shows the following information:
•
Date and time. The date and time the log entry was recorded.
•
Source IP. The IP address of the initiating device for this log entry.
•
Target address. The name or IP address of the website or news group visited or to which
access was attempted.
•
Action. Whether the access was blocked or allowed.
To refresh the log screen, click the Refresh button.
To clear the log entries, click the Clear Log button.
To email the log immediately, click the Send Log button.
Administration
86
R6200v2 Smart WiFi Router
Manage the Configuration File
The configuration settings of the router are stored within the router in a configuration file. You
can back up (save) this file to your computer, restore it, or reset it to the factory default
settings.
Back Up Settings

To back up the router’s configuration settings:
1. Select Advanced > Administration > Backup Settings.
2. Click Backup Settings.
3. Specify a location to store the .cfg file that is on a computer on your network.
A copy of the current settings is saved.
Restore Configuration Settings

To restore configuration settings that you backed up:
1. Select Advanced > Administration > Backup Settings.
2. Click the Browse button to find the cfg file.
3. Click the Restore button.
The files is uploaded to the router and the router reboots.
WARNING:
Do not interrupt the reboot process.
Administration
87
R6200v2 Smart WiFi Router
Erase the Current Configuration Settings
You can use the Erase button to erase the configuration and restore the factory default
settings. You might want to do this if you move the router to a different network or if you
changed the password and have forgotten what it is. (The default password is on the product
label.)
You can also use the Reset button on the back of the router to erase the configuration and
restore the factory settings. (See Factory Settings on page 128),.

To erase the configuration settings:
1. Select Advanced > Administration > Backup Settings.
2. Click the Erase button.
The factory default settings are restored. The user name is admin, the password to
password, and the LAN IP address is 192.168.1.1. DHCP is enabled.
Change the Password
This feature let you change the default password that is used to log in to the router with the
user name admin.
This is not the same as changing the password for wireless access. The label on the bottom
of your router shows your unique wireless network name (SSID) and password for wireless
access (see Label on page 11).

To set the password for the user name admin:
1. Select Advanced > Administration > Set Password.
2. On the Set Password screen, type the old password, and type the new password twice.
3. If you want to be able to recover the password, select the Enable Password Recovery
check box.
4. Click Apply.
Your changes take effect.
Administration
88
R6200v2 Smart WiFi Router
Password Recovery
NETGEAR recommends that you enable password recovery if you change the password for
the router user name admin. Then you can recover the password if it is forgotten. This
recovery process is supported in Internet Explorer, Firefox, and Chrome browsers, but not in
the Safari browser.

To set up password recovery:
1. Select Advanced > Administration > Set Password.
2. Select the Enable Password Recovery check box.
3. Select two security questions, and provide answers to them.
4. Click Apply.
Your changes are saved.

To recover your password:
1. In the address field of your browser, type www.routerlogin.net.
A login window displays.
2. Click Cancel.
If password recovery is enabled, you are prompted to answer two security questions.
3. Enter the saved answers to the security questions.
Administration
89
9.
Advanced Settings
S etting u p u niq ue situ at ions
This chapter describes the advanced features of your router. Networking knowledge is needed
to implement some of these features.
This chapter includes the following sections:
•
Advanced Wireless Settings
•
Wireless Access Point (AP)
•
Wireless Distribution System (WDS)
•
Dynamic DNS
•
Static Routes
•
Remote Management
•
Universal Plug and Play
•
IPv6
•
Traffic Meter
For information about approving a USB device, see Specify Approved USB Devices on page 54.
90
R6200v2 Smart WiFi Router
Advanced Wireless Settings
You can use this screen to turn the wireless radio on and off, to specify WPS settings, to use
AP mode, and to set up a wireless access list.
The Fragmentation Length, CTS/RTS Threshold, and Preamble Mode options in this screen
are reserved for wireless testing and advanced configuration only. Do not change these
settings unless you have a specific reason to do so.
Control the Wireless Radio
By default, the wireless radio is enabled so that you can connect wirelessly to the router. You
can turn the wireless radio on or off in the Advanced Wireless Settings screen or by using the
WiFi On/Off button on the router side panel. When the wireless radio is off, you can still use
an Ethernet cable for a LAN connection to the router.

To turn the wireless radio on or off:
1. Select Advanced > Advanced Setup > Wireless Settings.
By default, the Enable Wireless Router Radio check box is selected.
2. Select or clear the Enable Wireless Router Radio check box.
If you clear this check box, this turns off the WiFi feature of the wireless router.
3. (Optional) Select the Turn off wireless signal by schedule check box and fill in the fields
to specify the times when you do not need a wireless connection.
For example, you could turn off the wireless signal for the weekend if you leave town.
4. Click Apply.
Your changes take effect.
Advanced Settings
91
R6200v2 Smart WiFi Router
Set Up a Wireless Schedule
You can use this feature to turn off the wireless signal from your router at times when you do
not need a wireless connection. For example, you could turn it off for the weekend if you
leave town.

To configure and enable the wireless schedule:
1. Select Advanced > Advanced Setup > Wireless Settings.
The Advanced Wireless Settings screen displays.
2. Click the Add a new period button.
3. Use the menus, radio buttons, and check boxes to set up a period during which you want to
turn off the wireless signal.
4. Click the Apply button.
The Advanced Wireless Settings screen displays.
5. Select the Turn off wireless signal by schedule check box to activate the schedule.
6. Click the Apply button.
View or Change WPS Settings

To specify WPS Settings:
1. Select Advanced > Advanced Setup > Wireless Settings.
The Router’s PIN field displays the PIN that you use on a registrar (for example, from the
Network Explorer on a Vista Windows computer) to configure the router’s wireless
settings through WPS.
2. (Optional) Select or clear the Disable Router’s PIN check box.
The PIN function might temporarily be disabled when the router detects suspicious
attempts to break into the router’s wireless settings by using the router’s PIN through
WPS. You can manually enable the PIN function by clearing the Disable Router’s PIN
check box.
Advanced Settings
92
R6200v2 Smart WiFi Router
3. (Optional) Select or clear the Keep Existing Wireless Settings check box.
By default, the Keep Existing Wireless Settings check box is selected. NETGEAR
recommends that you leave this check box selected.
If you clear this check box, the next time a new wireless client uses WPS to connect to
the router, the router wireless settings change to an automatically generated random
SSID and security key.
4. Click Apply.
Your changes are saved.
Set Up a Wireless Access List by MAC Address
You can set up a list of computers and wireless devices that are allowed to join the wireless
network. This list is based on the unique MAC address of each computer and device.
Each network device has a MAC address, which is a unique 12-character physical address,
containing the hexadecimal characters 0–9, a–f, or A–F only, and separated by colons (for
example, 00:09:AB:CD:EF:01). Typically, the MAC address is on the label of the wireless
card or network interface device. If you do not have access to the label, you can display the
MAC address using the network configuration utilities of the computer. You might also find
the MAC addresses in the Attached Devices screen.

To restrict access based on MAC addresses:
1. Select Advanced > Advanced Setup > Wireless Settings.
2. Click the Setup Access List button.
3. Click Add.
The Wireless Card Access Setup screen opens and displays a list of currently active
wireless cards and their Ethernet MAC addresses.
4. If the computer or device you want is in the Available Wireless Cards list, select that radio
button; otherwise, type a name and the MAC address.
You can usually find the MAC address on the bottom of the wireless device.
Tip: You can copy and paste the MAC addresses from the Attached Devices
screen into the MAC Address field of this screen. To do this, use each
wireless computer to join the wireless network. The computer should be
listed in the Attached Devices screen.
Advanced Settings
93
R6200v2 Smart WiFi Router
5. Click Add.
The screen changes back to the list screen.
6. Add each computer or device you want to allow to connect wirelessly.
7. Select the Turn Access Control On check box.
8. Click Apply.

To edit a wireless device or delete it from the access list:
1. Select Advanced > Advanced Setup > Wireless Settings.
The Advanced Wireless Settings screen displays.
2. In the table, select the radio button next to the wireless device that you want to edit or delete.
3. Do one of the following:
• Click the Edit button.
The Edit Wireless Card screen displays.
a. Edit the address information.
•
b. Click the Accept button.
Click the Delete button.
The address is removed from the table.
Wireless Access Point (AP)
You can set up the router to run as an access point (AP) on the same local network as
another router.

To set up the router as an AP:
1. Use an Ethernet cable to connect the Internet port of this router to a LAN port in the
other router.
Cable this port to a LAN port
on the other router
2. Select Advanced > Advanced Setup > Wireless Settings.
3. Select the Enable Access Point Mode check box.
Advanced Settings
94
R6200v2 Smart WiFi Router
The AP Mode section of the screen expands.
4. Select the check box for the IP address setting that you want to use:
• Get an IP address dynamically from the other router. The other router on the
network assigns an IP address to this router while this router is in AP mode.
•
Fixed IP address (not recommended). Use this setting if you want to manually
assign a specific IP address to this router while it is in AP mode. Using this option
effectively requires advanced network experience.
Note: To avoid interference with other routers or gateways in your network,
NETGEAR recommends that you use different wireless settings on the router
in access point mode.You could also turn off the wireless radio on the other
router or gateway and use your router only for wireless client access.
5. Click the Apply button.
The IP address of the router changes, and you are disconnected. To reconnect, close and
restart your web browser, and type http://www.routerlogin.net.
Advanced Settings
95
R6200v2 Smart WiFi Router
Set Up the Router in Bridge Mode
You can use your R6200v2 Smart WiFi Router in Bridge mode to connect multiple devices
wirelessly at the faster 802.11ac speed. To do this, you need two WiFi Routers: one set up as
a router and the other set up as a bridge.
R6200v2 Smart WiFi Router
R6200v2 Smart WiFi Router in Bridge mode
FOR POSITION ONLY
Figure 8. Router in Bridge mode with an 802.11ac WiFi connection
Installing your R6200v2 Smart WiFi Router as a bridge offers the following benefits:
•
You can take advantage of gigabit WiFi speeds on current devices.
•
Use Gigabit WiFi for applications like video and gaming.
•
Connect multiple devices like NAS, Smart TV, NeoTV, Blu-ray Player, and game consoles
at gigabit WiFi speeds using a WiFi link.
•
Avoid the need for separate WiFi adapters for each device.
For example, you could install the first router in a room like a home office that has your
Internet connection. Then set up the second router in Bridge mode. Then place the router in
Bridge mode in a different room that has your home entertainment center. Cable the router in
Bridge mode to your Smart TV, DVR, game console or Blu-ray player, and use its 802.11ac
WiFi connection to the first router.

To set up Bridge mode:
1. Make a note of the WiFi settings of the other router to which this router will connect:
You need to know the SSID, WiFi security mode, wireless password, and operating
frequency (either 2.4 GHz or 5 GHz).
2. On the R6200v2 Smart WiFi Router that will run in Bridge mode, select Advanced >
Advanced Setup > Wireless Settings.
Advanced Settings
96
R6200v2 Smart WiFi Router
3. Scroll down and select the Use other operation mode check box and the Enable Bridge
mode radio button.
The screen adjusts.
4. Click the setup bridge mode wireless settings button.
5. Specify the settings of the other router to which this router will connect.
a. Select the wireless network frequency (2.4 GHz or 5 GHz).
For 802.11ac mode, select 5 GHz.
b. In the Name (SSID) field, enter the wireless network name (SSID).
c. In the Security Option section, select a radio button.
d. If prompted, type the passphrase (the WiFi password that you use to connect
wirelessly to the other router).
6. Click Apply.
The settings for the other router are saved and the Advanced Wireless Settings screen
displays.
7. Click Apply on the Advanced Wireless Settings screen.
Your changes take effect.
Advanced Settings
97
R6200v2 Smart WiFi Router
Wireless Distribution System (WDS)
You can set the router up to be used as a wireless base station or a wireless repeater in a
wireless distribution system (WDS). A WDS lets you expand a wireless network through
multiple access points. A wireless base station connects to the Internet, can have wired and
wireless clients, and sends its wireless signal to an access point that functions as a wireless
repeater. A wireless repeater can also have wired and wireless clients, but connects to the
Internet through the wireless base station. The following figure shows a wireless repeating
scenario.
FOR POSITION ONLY
Repeater
access point
Base station
access point
Figure 9. Wireless repeating scenario
Note: To use the wireless repeating function, you need to select None as
the security option in the Wireless Settings screen, and you cannot
select Auto Channel.
Wireless base station. The router acts as the parent access point that bridges traffic to and
from the child repeater access point. The base station also handles wireless and wired local
computers. To configure this mode, you have to know the MAC addresses of the child
repeater access point. Often, the MAC address is on the product label.
Wireless repeater. The router sends all traffic from its local wireless or wired computers to a
remote access point. To configure this mode, you have to know the MAC address of the
remote parent access point.
The router is always in dual-band concurrent mode, unless you turn off one radio. If you
enable the wireless repeater in either radio band, the wireless base station or wireless
repeater cannot be enabled in the other radio band. However, if you enable the wireless base
Advanced Settings
98
R6200v2 Smart WiFi Router
station in either radio band and use the other radio band as a wireless router or wireless base
station, dual-band concurrent mode is not affected.
For you to set up a wireless network with WDS, both access points have to meet the
following conditions:
•
Both access points have to use the same SSID, wireless channel, and encryption mode.
•
Both access points have to be on the same LAN IP subnet. That is, all of the access point
LAN IP addresses are in the same network.
•
All LAN devices (wired and wireless computers) are configured to operate in the same
LAN network address range as the access points.
Set Up the Base Station
The wireless repeating function works only in hub and spoke mode. The units cannot be
daisy-chained. You have to know the wireless settings for both units. You have to know the
MAC address of the remote unit. First, set up the base statiomn. Then set up the repeater.

To set up the base station:
1. Set up both units with the same wireless settings.
The SSID and mode need to be the same and the wireless security option has to be set
to None. (See Basic Wireless Settings on page 24.)
2. Select Advanced > Advanced Setup > Wireless Repeating Function.
3. Select the Enable Wireless Repeating Function check box.
4. Select the Wireless Base Station radio button.
5. (Optional) Select the Disable Wireless Client Association check box to prevent wireless
clients from associating with the base station and allow LAN client associations only.
You can leave the check box cleared if you prefer wireless clients to be able to associate
with the base stations.
Advanced Settings
99
R6200v2 Smart WiFi Router
6. In the Repeater MAC Address 1 through 4 fields, enter the MAC addresses for the access
points that should function as repeaters.
If your router is the base station, it can function as the “parent” for up to four other access
points.
7. Click the Apply button.
Your changes are saved.
Set Up a Repeater
Use a wired Ethernet connection to set up the repeater unit to avoid conflicts with the wireless
connection to the base station.
Note: If you are using the router as the base station with a non-NETGEAR
router as the repeater, you might need to change more configuration
settings. In particular, you should disable the DHCP server function
on the access point that is the repeater.

To configure the router as a repeater:
1. Log in to the router that will be the repeater.
2. Select Basic > Wireless Settings and verify that the wireless settings match the base unit
exactly.
The wireless security option has to be set to WEP or None.
3. Select Advanced > Wireless Repeating Function.
4. Select the Enable Wireless Repeating Function check box.
5. Select the Wireless Repeater radio button.
6. Fill in the Repeater IP Address field.
Advanced Settings
100
R6200v2 Smart WiFi Router
This IP address has to be in the same subnet as the base station, but different from the
LAN IP address of the base station.
7. (Optional) Select the Disable Wireless Client Association check box to prevent wireless
clients from associating with the repeater and allowing LAN client associations only.
You can leave the check box cleared if you prefer wireless clients to be able to associate
with the repeater.
8. In the Base Station MAC Address field, enter the MAC addresses for the access point that
should function as the base station.
9. Click Apply.
Your changes are saved.
10. Verify connectivity across the LANs.
A computer on any wireless or wired LAN segment of the router can connect to the
Internet or share files and printers with any other computer or server connected to the
other access point.
Dynamic DNS
If your Internet service provider (ISP) gave you a permanently assigned IP address, you can
register a domain name and have that name linked with your IP address by public Domain
Name Servers (DNS). However, if your Internet account uses a dynamically assigned IP
address, you do not know in advance what your IP address will be, and the address can
change frequently. In this case, you can use a commercial Dynamic DNS service. This type
of service lets you register your domain to their IP address and forwards traffic directed at
your domain to your frequently changing IP address.
If your ISP assigns a private WAN IP address (such as 192.168.x.x or 10.x.x.x), the Dynamic
DNS service does not work because private addresses are not routed on the Internet.
Your router contains a client that can connect to the Dynamic DNS service provided by
DynDNS.org. First visit their website at http://www.dyndns.org and obtain an account and
host name that you configure in the router. Then, whenever your ISP-assigned IP address
changes, your router automatically contacts the Dynamic DNS service provider, logs in to
your account, and registers your new IP address. If your host name is hostname, for
example, you can reach your router at http://hostname.dyndns.org.
Advanced Settings
101
R6200v2 Smart WiFi Router

To set up Dynamic DNS:
1. Select Advanced > Advanced Setup > Dynamic DNS.
2. Register for an account with one of the Dynamic DNS service providers whose URLs are in
the Service Provider list.
3. Select the Use a Dynamic DNS Service check box.
4. Select the URL of your Dynamic DNS service provider.
For example, for DynDNS.org, select www.dyndns.org.
5. Type the host name (or domain name) that your Dynamic DNS service provider gave you.
6. Type the user name for your Dynamic DNS account.
This user name is the name that you use to log in to your account, not your host name.
7. Type the password (or key) for your Dynamic DNS account.
8. Click Apply.
Your changes are saved.
Static Routes
Static routes provide more routing information to your router. Typically, you do not need to
add static routes. You have to configure static routes only for unusual cases such as multiple
routers or multiple IP subnets on your network.
As an example of when a static route is needed, consider the following case:
•
Your primary Internet access is through a cable modem to an ISP.
•
You have an ISDN router on your home network for connecting to the company where
you are employed. This router’s address on your LAN is 192.168.1.100.
•
Your company’s network address is 134.177.0.0.
When you first configured your router, two implicit static routes were created. A default route
was created with your ISP as the gateway, and a second static route was created to your
local network for all 192.168.1.x addresses. With this configuration, if you attempt to access a
device on the 134.177.0.0 network, your router forwards your request to the ISP. The ISP
forwards your request to the company where you are employed, and the request is likely to
be denied by the company’s firewall.
Advanced Settings
102
R6200v2 Smart WiFi Router
In this case you have to define a static route, telling your router that 134.177.0.0 should be
accessed through the ISDN router at 192.168.1.100. In this example:

•
The Destination IP Address and IP Subnet Mask fields specify that this static route
applies to all 134.177.x.x addresses.
•
The Gateway IP Address field specifies that all traffic for these addresses should be
forwarded to the ISDN router at 192.168.1.100.
•
A metric value of 1 works because the ISDN router is on the LAN.
•
Private is selected only as a precautionary security measure in case RIP is activated.
To set up a static route:
1. Select Advanced > Advanced Setup > Static Routes.
2. Click Add.
3. In the Route Name field, type a name for this static route (for identification purposes only.)
4. Select the Private check box if you want to limit access to the LAN only.
If Private is selected, the static route is not reported in RIP.
5. Select the Active check box to make this route effective.
6. Type the IP address of the final destination.
7. Type the IP subnet mask for this destination. If the destination is a single host, type
255.255.255.255.
8. Type the gateway IP address, which has to be on the same LAN segment as the router.
9. Type a number from 1 through 15 as the metric value.
This value represents the number of routers between your network and the destination.
Usually, a setting of 2 or 3 works, but if this is a direct connection, set it to 1.
10. Click the Apply button.
The static route is added.

To edit or delete a static route:
1. Select Advanced > Advanced Setup > Static Routes.
The Static Routes screen displays.
2. In the table, select the radio button next to the route that you want to edit or delete.
3. Do one of the following:
Advanced Settings
103
R6200v2 Smart WiFi Router
•
Click the Edit button.
The Static Routes screen adjusts.
a. Edit the route information.
•
b. Click the Apply button.
Click the Delete button.
The route is removed from the table.
Remote Management
The remote management feature lets you access your router over the Internet to view or
change its settings.
Note: Be sure to change the router default login password to a secure
password. The ideal password contains no dictionary words from
any language and contains uppercase and lowercase letters,
numbers, and symbols. It can be up to 30 characters. See Change
the Password on page 88.

To set up remote management:
1. Select Advanced > Advanced Setup > Remote Management.
2. Select the Turn Remote Management On check box.
3. Under Allow Remote Access By, specify the external IP addresses to be allowed to access
the router’s remote management.
Note: For enhanced security, restrict access to as few external IP addresses
as practical.
Advanced Settings
104
R6200v2 Smart WiFi Router
•
To allow access from a single IP address on the Internet, select Only This Computer.
Enter the IP address that will be allowed access.
•
To allow access from a range of IP addresses on the Internet, select IP Address
Range. Enter a beginning and ending IP address to define the allowed range.
•
To specify IP addresses, select IP Address List and type in the allowed IP
addresses.
•
To allow access from any IP address on the Internet, select Everyone.
4. Specify the port number for accessing the web management interface.
Normal web browser access uses the standard HTTP service port 80. For greater
security, enter a custom port number for the remote web management interface. Choose
a number from 1024 to 65535, but do not use the number of any common service port.
The default is 8080, which is a common alternate for HTTP.
5. Click the Apply button.
Your changes take effect.
6. When you access your router from the Internet, type your router’s WAN IP address into your
browser’s address or location field followed by a colon (:) and the custom port number.
For example, if your external address is 134.177.0.123 and you use port number 8080,
enter http://134.177.0.123:8080 in your browser.
Universal Plug and Play
Universal Plug and Play (UPnP) helps devices, such as Internet appliances and computers,
access the network and connect to other devices as needed. UPnP devices can
automatically discover the services from other registered UPnP devices on the network.
If you use applications such as multiplayer gaming, peer-to-peer connections, or real-time
communications such as instant messaging or remote assistance (a feature in Windows XP),
you should enable UPnP.

To turn on Universal Plug and Play:
1. Select Advanced > Advanced Setup > UPnP.
The UPnP screen displays.
2. Select the Turn UPnP On check box.
Advanced Settings
105
R6200v2 Smart WiFi Router
By default, this check box is selected. UPnP for automatic device configuration can be
enabled or disabled. If the Turn UPnP On check box is cleared, the router does not allow
any device to automatically control the resources, such as port forwarding (mapping), of
the router.
3. Type the advertisement period in minutes.
The advertisement period specifies how often the router broadcasts its UPnP information.
This value can range from 1 to 1440 minutes. The default period is 30 minutes. Shorter
durations ensure that control points have current device status at the expense of
additional network traffic. Longer durations can compromise the freshness of the device
status, but can significantly reduce network traffic.
4. Type the advertisement time to live in hops.
The time to live for the advertisement is measured in hops (steps) for each UPnP packet
sent. Hops are the steps a packet takes between routers. The number of hops can range
from 1 to 255. The default value for the advertisement time to live is 4 hops, which should
be fine for most home networks. If you notice that some devices are not being updated or
reached correctly, it might be necessary to increase this value.
5. Click the Apply button.
The UPnP Portmap table displays the IP address of each UPnP device that is accessing
the router and which ports (internal and external) that device has opened. The UPnP
Portmap table also displays what type of port is open and whether that port is still active
for each IP address.
6. (Optional) To refresh the information in the UPnP Portmap table, click the Refresh button.
IPv6
You can use this feature to set up an IPv6 Internet connection type if genie does not detect it
automatically.

To set up an IPv6 Internet connection type:
1. Select Advanced > Advanced Setup > IPv6.
2. In the Internet Connection Type list, select the IPv6 connection type.
Your Internet service provider (ISP) can provide this information.
•
If your ISP did not provide details, you can select IPv6 Tunnel.
Advanced Settings
106
R6200v2 Smart WiFi Router
•
If you are not sure, select Auto Detect so that the router detects the IPv6 type that is
in use.
•
If your Internet connection does not use PPPoE, DHCP, or fixed, but is IPv6, select
Auto Config.
For more information about Internet connection types, see the following sections.
3. Click the Apply button.
Your changes take effect.
Requirements for Entering IPv6 Addresses
IPv6 addresses are denoted by eight groups of hexadecimal quartets that are separated by
colons. Any four-digit group of zeroes within an IPv6 address can be reduced to a single zero
or altogether omitted.
The following errors invalidate an IPv6 address:
•
More than eight groups of hexadecimal quartets
•
More than four hexadecimal characters in a quartet
•
More than two colons in a row
Auto Detect

To set up an IPv6 Internet connection through auto detection:
1. Select Advanced > Advanced Setup > IPv6.
The IPv6 screen displays.
2. In the Internet Connection Type list, select Auto Detect.
The screen adjusts:
The router automatically detects the information in the following fields:
•
Connection Type. This field indicates the connection type that is detected.
Advanced Settings
107
R6200v2 Smart WiFi Router
•
Router’s IPv6 Address on WAN. This field shows the IPv6 address that is acquired
for the router’s WAN (or Internet) interface. The number after the slash (/) is the length
of the prefix, which is also indicated by the underline (_) under the IPv6 address. If no
address is acquired, the field displays Not Available.
•
Router’s IPv6 Address on LAN. This field shows the IPv6 address that is acquired
for the router’s LAN interface. The number after the slash (/) is the length of the prefix,
which is also indicated by the underline (_) under the IPv6 address. If no address is
acquired, the field displays Not Available.
3. Specify how the router assigns IPv6 addresses to the devices on your home network (the
LAN) by selecting one of the following radio buttons:
• Use DHCP Server. This method passes more information to LAN devices, but some
IPv6 systems might not support the DHCv6 client function.
•
Auto Config. This is the default setting.
4. (Optional) Select the Use This Interface ID check box, and specify the interface ID that you
want to be used for the IPv6 address of the router’s LAN interface.
If you do not specify an ID here, the router generates one automatically from its MAC
address.
5. Click the Apply button.
IPv6 Auto Config

To set up an IPv6 Internet connection through auto configuration:
1. Select Advanced > Advanced Setup > IPv6.
The IPv6 screen displays.
2. In the Internet Connection Type list, select Auto Config.
The screen adjusts:
The router automatically detects the information in the following fields:
Advanced Settings
108
R6200v2 Smart WiFi Router
•
Router’s IPv6 Address on WAN. This field shows the IPv6 address that is acquired
for the router’s WAN (or Internet) interface. The number after the slash (/) is the length
of the prefix, which is also indicated by the underline (_) under the IPv6 address. If no
address is acquired, the field displays Not Available.
•
Router’s IPv6 Address on LAN. This field shows the IPv6 address that is acquired
for the router’s LAN interface. The number after the slash (/) is the length of the prefix,
which is also indicated by the underline (_) under the IPv6 address. If no address is
acquired, the field displays Not Available.
3. (Optional) In the DHCP User Class (If Required) field, enter a host name.
Most people do not need to fill in this field, but if your ISP has given you a specific host
name, enter it here.
4. (Optional) In the Domain Name (If Required) field, enter a domain name.
You can type the domain name of your IPv6 ISP. (Do not enter the domain name for the
IPv4 ISP here.) For example, if your ISP’s mail server is mail.xxx.yyy.zzz, you would type
xxx.yyy.zzz as the domain name. If your ISP provided a domain name, type it in this field.
(For example, Earthlink Cable might require a host name of home, and Comcast
sometimes supplies a domain name.)
5. Specify how the router assigns IPv6 addresses to the devices on your home network (the
LAN) by selecting one of the following radio buttons:
• Use DHCP Server. This method passes more information to LAN devices, but some
IPv6 systems might not support the DHCv6 client function.
•
Auto Config. This is the default setting.
6. (Optional) Select the Use This Interface ID check box, and specify the interface ID that you
want to be used for the IPv6 address of the router’s LAN interface.
If you do not specify an ID here, the router generates one automatically from its MAC
address.
7. Click the Apply button.
IPv6 6to4 Tunnel
The remote relay router is the router to which your router creates the 6to4 tunnel. Make sure
that the IPv4 Internet connection is working before you apply the 6to4 tunnel settings for the
IPv6 connection.

To set up an IPv6 Internet connection by using a 6to4 tunnel:
1. Select Advanced > Advanced Setup > IPv6.
The IPv6 screen displays.
2. In the Internet Connection Type list, select 6to4 Tunnel.
Advanced Settings
109
R6200v2 Smart WiFi Router
The screen adjusts:
The router automatically detects the information in the following fields:
•
Router’s IPv6 Address on WAN. This field shows the IPv6 address that is acquired
for the router’s WAN (or Internet) interface. The number after the slash (/) is the length
of the prefix, which is also indicated by the underline (_) under the IPv6 address. If no
address is acquired, the field displays Not Available.
•
Router’s IPv6 Address on LAN. This field shows the IPv6 address that is acquired
for the router’s LAN interface. The number after the slash (/) is the length of the prefix,
which is also indicated by the underline (_) under the IPv6 address. If no address is
acquired, the field displays Not Available.
3. Configure the remote 6to4 relay router settings by selecting one of the following buttons:
• Auto. Your router uses any remote relay router that is available on the Internet. This is
the default setting.
•
Static IP Address. Enter the static IPv4 address of the remote relay router. This
address is usually provided by your IPv6 ISP.
4. Specify how the router assigns IPv6 addresses to the devices on your home network (the
LAN) by selecting one of the following radio buttons:
• Use DHCP Server. This method passes more information to LAN devices, but some
IPv6 systems might not support the DHCv6 client function.
•
Auto Config. This is the default setting.
5. (Optional) Select the Use This Interface ID check box, and specify the interface ID that you
want to be used for the IPv6 address of the router’s LAN interface.
If you do not specify an ID here, the router generates one automatically from its MAC
address.
6. Click the Apply button.
Advanced Settings
110
R6200v2 Smart WiFi Router
IPv6 Pass Through
In pass-through mode, the router works as a Layer 2 Ethernet switch with two ports (LAN and
WAN Ethernet ports) for IPv6 packets. The router does not process any IPv6 header packets.

To set up a pass-through IPv6 Internet connection:
1. Select Advanced > Advanced Setup > IPv6.
The IPv6 screen displays.
2. In the Internet Connection Type list, select Pass Through.
The screen adjusts, but no additional fields display.
3. Click the Apply button.
IPv6 Fixed

To set up a pass-through IPv6 Internet connection:
1. Select Advanced > Advanced Setup > IPv6.
The IPv6 screen displays.
2. Select Fixed from the menu.
The screen adjusts:
3. Configure the fixed IPv6 addresses for the WAN connection:
• IPv6 Address/Prefix Length. The IPv6 address and prefix length of the router WAN
interface.
•
Default IPv6 Gateway. The IPv6 address of the default IPv6 gateway for the router’s
WAN interface.
•
Primary DNS Server. The primary DNS server that resolves IPv6 domain name
records for the router.
Advanced Settings
111
R6200v2 Smart WiFi Router
•
Secondary DNS Server. The secondary DNS server that resolves IPv6 domain
name records for the router.
Note: If you do not specify the DNS servers, the router uses the DNS servers
that are configured for the IPv4 Internet connection on the Internet Setup
screen. (See Internet Setup on page 20.)
4. Specify how the router assigns IPv6 addresses to the devices on your home network (the
LAN) by selecting one of the following radio buttons:
• Use DHCP Server. This method passes more information to LAN devices, but some
IPv6 systems might not support the DHCv6 client function.
•
Auto Config. This is the default setting.
5. In the IPv6 Address/Prefix Length fields, specify the static IPv6 address and prefix length of
the router’s LAN interface.
If you do not specify an ID here, the router generates one automatically from its MAC
address.
6. Click the Apply button.
IPv6 DHCP

To set up an IPv6 Internet connection with a DHCP server:
1. Select Advanced > Advanced Setup > IPv6.
The IPv6 screen displays.
2. In the Internet Connection Type list, select DHCP.
The screen adjusts:
The router automatically detects the information in the following fields:
•
Router’s IPv6 Address on WAN. This field shows the IPv6 address that is acquired
for the router’s WAN (or Internet) interface. The number after the slash (/) is the length
Advanced Settings
112
R6200v2 Smart WiFi Router
of the prefix, which is also indicated by the underline (_) under the IPv6 address. If no
address is acquired, the field displays Not Available.
•
Router’s IPv6 Address on LAN. This field shows the IPv6 address that is acquired
for the router’s LAN interface. The number after the slash (/) is the length of the prefix,
which is also indicated by the underline (_) under the IPv6 address. If no address is
acquired, the field displays Not Available.
3. (Optional) In the DHCP User Class (If Required) field, enter a host name.
Most people do not need to fill in this field, but if your ISP has given you a specific host
name, enter it here.
4. (Optional) In the Domain Name (If Required) field, enter a domain name.
You can type the domain name of your IPv6 ISP. (Do not enter the domain name for the
IPv4 ISP here.) For example, if your ISP’s mail server is mail.xxx.yyy.zzz, you would type
xxx.yyy.zzz as the domain name. If your ISP provided a domain name, type it in this field.
(For example, Earthlink Cable might require a host name of home, and Comcast
sometimes supplies a domain name.)
5. Specify how the router assigns IPv6 addresses to the devices on your home network (the
LAN) by selecting one of the following radio buttons:
• Use DHCP Server. This method passes more information to LAN devices, but some
IPv6 systems might not support the DHCv6 client function.
•
Auto Config. This is the default setting.
6. (Optional) Select the Use This Interface ID check box, and specify the interface ID that you
want to be used for the IPv6 address of the router’s LAN interface.
If you do not specify an ID here, the router generates one automatically from its MAC
address.
7. Click the Apply button.
IPv6 PPPoE

To set up a PPPoE IPv6 Internet connection:
1. Select Advanced > Advanced Setup > IPv6.
The IPv6 screen displays.
2. In the Internet Connection Type list, select PPPoE.
Advanced Settings
113
R6200v2 Smart WiFi Router
The screen adjusts:
The router automatically detects the information in the following fields:
•
Router’s IPv6 Address on WAN. This field shows the IPv6 address that is acquired
for the router’s WAN (or Internet) interface. The number after the slash (/) is the length
of the prefix, which is also indicated by the underline (_) under the IPv6 address. If no
address is acquired, the field displays Not Available.
•
Router’s IPv6 Address on LAN. This field shows the IPv6 address that is acquired
for the router’s LAN interface. The number after the slash (/) is the length of the prefix,
which is also indicated by the underline (_) under the IPv6 address. If no address is
acquired, the field displays Not Available.
3. In the Login field, enter the login information for the ISP connection.
This is usually the name that you use in your email address. For example, if your main
mail account is JerAB@ISP.com, then you would type JerAB in this field. Some ISPs (like
Mindspring, Earthlink, and T-DSL) require that you use your full email address when you
log in. If your ISP requires your full email address, type it in this field.
4. In the Password field, enter the password for the ISP connection.
5. In the Service Name name field, enter a service name.
If your ISP did not provide a service name, leave this field blank.
Note: The default setting of the Connection Mode field is Always on to provide
a steady IPv6 connection. The router never terminates the connection. If the
connection is terminated, for example, when the modem is turned off, the router
attempts to reestablish the connection immediately after the PPPoE connection
becomes available again.
6. Specify how the router assigns IPv6 addresses to the devices on your home network (the
LAN) by selecting one of the following radio buttons:
Advanced Settings
114
R6200v2 Smart WiFi Router
•
Use DHCP Server. This method passes more information to LAN devices, but some
IPv6 systems might not support the DHCv6 client function.
•
Auto Config. This is the default setting.
7. (Optional) Select the Use This Interface ID check box, and specify the interface ID that you
want to be used for the IPv6 address of the router’s LAN interface.
If you do not specify an ID here, the router generates one automatically from its MAC
address.
8. Click the Apply button.
Traffic Meter
Traffic metering allows you to monitor the volume of Internet traffic that passes through the
router Internet port. You can set limits for traffic volume.

To monitor Internet traffic:
1. Click Advanced > Advanced Setup > Traffic Meter.
Scroll to view
more settings
2. Select the Enable Traffic Meter check box.
3. (Optional) Control the volume of Internet traffic.
You can use either the traffic volume control feature or the connection time control
feature.
•
•
Select the Traffic volume control by radio button and then select one of the
following options:
No Limit. No restriction is applied when the traffic limit is reached.
Download only. The restriction is applied to incoming traffic only.
Both Directions. The restriction is applied to both incoming and outgoing traffic.
Select the Connection time control radio button and enter the allowed hours in the
Monthly limit field.
Advanced Settings
115
R6200v2 Smart WiFi Router
4. (Optional) If your ISP charges for extra data volume when you make a new connection,
enter the extra data volume in MB in the Round up data volume for each connection by field.
5. In the Traffic Counter section, set the traffic counter to begin at a specific time and date.
If you want the traffic counter to start immediately, click the Restart Counter Now button.
6. In the Traffic Control section, specify whether the router should issue a warning message
before the monthly limit of Mbytes or hours is reached.
By default, the value is 0 and no warning message is issued. You can select one of the
following to occur when the limit is attained:
•
The Internet LED flashes green or amber.
•
The Internet connection is disconnected and disabled.
7. Click the Apply button.
The Internet Traffic Statistics section helps you to monitor the data traffic.
Click the Refresh button to update the Traffic Statistics section.
Click the Traffic Status button to display more information about the data traffic on your
router and to change the poll interval.
Advanced Settings
116
10.
10
Troubleshooting
This chapter provides information to help you diagnose and solve problems you might have with
your router. If you do not find the solution here, check the NETGEAR support site at
http://support.netgear.com for product and contact information.
This chapter contains the following sections:
•
Quick Tips
•
Troubleshoot with the LEDs
•
Cannot Log In to the Router
•
Cannot Access the Internet
•
Changes Not Saved
•
Wireless Connectivity
•
Troubleshoot Your Network Using the Ping Utility
117
R6200v2 Smart WiFi Router
Quick Tips
This section describes tips for troubleshooting some common problems.
Sequence to Restart Your Network
When you need to restart your network, follow this sequence:
1. Turn off and unplug the modem.
2. Turn off the router.
3. Plug in the modem and turn it on. Wait 2 minutes.
4. Turn on the router and wait 2 minutes.
Check Ethernet Cable Connections
If your device does not power on, make sure that the Ethernet cables are securely plugged
in.
•
The Internet LED on the router is on if the Ethernet cable connecting the router and the
modem is plugged in securely and the modem and router are turned on.
•
For each powered-on computer connected to the router by an Ethernet cable, the
corresponding numbered router LAN port LED is on.
Wireless Settings
Make sure that the wireless settings in the computer and router match exactly.
•
For a wirelessly connected computer, the wireless network name (SSID) and wireless
security settings of the router and wireless computer need to match exactly.
•
If you set up an access list in the Advanced Wireless Settings screen, you have to add
each wireless computer’s MAC address to the router’s access list.
Network Settings
Make sure that the network settings of the computer are correct.
•
Wired and wirelessly connected computers need to have network (IP) addresses on the
same network as the router. The simplest way to do this is to configure each computer to
obtain an IP address automatically using DHCP.
•
Some cable modem service providers require you to use the MAC address of the
computer initially registered on the account. You can view the MAC address in the
Attached Devices screen.
Troubleshooting
118
R6200v2 Smart WiFi Router
Troubleshoot with the LEDs
After you turn on power to the router, the following sequence of events should occur:
1. When power is first applied, verify that the Power/Test LED
is lit.
2. Verify that the Power/Test LED turns amber within a few seconds, indicating that the self-test
is running.
3. After approximately 30 seconds, verify the following:
• The Power/Test LED is solid green.
•
The Internet LED is lit.
•
The Wireless LED is lit unless you turned off the wireless radio.
The LEDs on the front panel of the router can be used for troubleshooting.
Power/Test LED Is Off or Blinking
•
Make sure that the power cord is securely connected to your router and that the power
adapter is securely connected to a functioning power outlet.
•
Check that you are using the 12V DC, 2.5A power adapter that NETGEAR supplied for
this product.
•
If the Power/Test LED blinks slowly and continuously, the router firmware is corrupted.
This can happen if a firmware upgrade is interrupted, or if the router detects a problem
with the firmware. If the error persists, you have a hardware problem. For recovery
instructions, or help with a hardware problem, contact technical support at
www.netgear.com/support.
Power/Test LED Stays Amber
When the router is turned on, the Power/Test LED turns amber for about 20 seconds and
then turns green. If the LED does not turn green, the router has a problem.
If the Power/Test LED is still amber 1 minute after you turn on power to the router:
1. Turn off the power and then turn it back on to see if the router recovers.
2. Press and hold the Reset button to return the router to its factory settings.
See Troubleshoot Your Network Using the Ping Utility on page 125.
If the error persists, you might have a hardware problem. Contact technical support at
www.netgear.com/support.
Troubleshooting
119
R6200v2 Smart WiFi Router
LEDs Never Turn Off
When the router is turned on, the LEDs turn on for about 10 seconds and then turn off. If all
the LEDs stay on, this indicates a fault within the router.
If all LEDs are still on 1 minute after power-up:
•
Cycle the power to see if the router recovers.
•
Press and hold the Reset button to return the router to its factory settings. For more
information, see Troubleshoot Your Network Using the Ping Utility on page 125.
If the error persists, you might have a hardware problem. Contact technical support at
www.netgear.com/support.
Internet or Ethernet Port LEDs Are Off
If either the Ethernet port LEDs or the Internet LED does not light when the Ethernet
connection is made, check the following:
•
Make sure that the Ethernet cable connections are secure at the router and at the modem
or computer.
•
Make sure that power is turned on to the connected modem or computer.
•
Be sure that you are using the correct cable.
When connecting the router’s Internet port to a cable or DSL modem, use the cable that
was supplied with the cable or DSL modem. This cable could be a standard
straight-through Ethernet cable or an Ethernet crossover cable.
Wireless LEDs Are Off
If the Wireless LEDs stay off, check to see if the WiFi On/Off button on the router has been
pressed. This button turns the wireless radios in the router on and off. The Wireless LEDs are
lit when the wireless radio is turned on.
The Push 'N' Connect (WPS) Button Blinks Amber
If you use the WPS function, and the WPS LED blinks amber, check the following:
•
Make sure that you are using the button and not the router’s built-in registrar.
•
Check that PIN verification has succeeded for the wireless device you are adding to the
wireless network.
•
Make sure that you have not pressed the WPS button on the side of the router after
disabling the WPS feature (you logged in to the router and disabled this previously).
•
Check that the router is not in the temporary AP setup locked state (if you are using the
wireless repeater function).
Troubleshooting
120
R6200v2 Smart WiFi Router
Cannot Log In to the Router
If you are unable to log in to the router from a computer on your local network, check the
following:
•
If you are using an Ethernet-connected computer, check the Ethernet connection
between the computer and the router.
•
Make sure that the IP address of your computer is on the same subnet as the router. If
you are using the recommended addressing scheme, your computer’s address should be
in the range of 192.168.1.2 to 192.168.1.254.
•
If your computer’s IP address is shown as 169.254.x.x, recent versions of Windows and
Mac OS generate and assign an IP address if the computer cannot reach a DHCP server.
These autogenerated addresses are in the range of 169.254.x.x. If your IP address is in
this range, check the connection from the computer to the router, and reboot your
computer.
•
If your router’s IP address was changed and you do not know the current IP address,
clear the router’s configuration to factory defaults. This sets the router’s IP address to
192.168.1.1. For more information, see Factory Settings on page 128.
•
Make sure that your browser has Java, JavaScript, or ActiveX enabled. If you are using
Internet Explorer, click Refresh to be sure that the Java applet is loaded.
•
Try quitting the browser and launching it again.
•
Make sure that you are using the correct login information. The factory default login name
is admin, and the password is password. Make sure that Caps Lock is off when you
enter this information.
•
If you are attempting to set up your NETGEAR router as an additional router behind an
existing router in your network, consider replacing the existing router. NETGEAR does
not support such a configuration.
•
If you are attempting to set up your NETGEAR router as a replacement for an ADSL
gateway in your network, the router cannot perform many gateway services. For
example, the router cannot convert ADSL or cable data into Ethernet networking
information. NETGEAR does not support such a configuration.
Cannot Access the Internet
If you can access your router but not the Internet, check to see if the router can obtain an IP
address from your Internet service provider (ISP). Unless your ISP provides a fixed IP
address, your router requests an IP address from the ISP. You can determine whether the
request was successful using the Router Status screen.

To check the WAN IP address:
1. Start your browser, and select an external site such as www.netgear.com.
2. Access the router interface at www.routerlogin.net.
3. Select Administration > Router Status.
Troubleshooting
121
R6200v2 Smart WiFi Router
4. Check that an IP address is shown for the Internet port. If 0.0.0.0 is shown, your router has
not obtained an IP address from your ISP.
If your router cannot obtain an IP address from the ISP, you might need to force your cable or
DSL modem to recognize your new router by restarting your network. For more information,
see Sequence to Restart Your Network on page 118.
If your router is still unable to obtain an IP address from the ISP, the problem might be one of
the following:
•
Your Internet service provider (ISP) might require a login program.
Ask your ISP whether they require PPP over Ethernet (PPPoE) or some other type of
login.
•
If your ISP requires a login, the login name and password might be set incorrectly.
•
Your ISP might check for your computer’s host name.
Assign the computer host name of your ISP account as the account name in the Internet
Setup screen.
•
Your ISP allows only one Ethernet MAC address to connect to Internet and might check
for your computer’s MAC address. In this case, do one of the following:
Inform your ISP that you have bought a new network device, and ask them to use the
router’s MAC address.
Configure your router to clone your computer’s MAC address.
If your router can obtain an IP address, but your computer is unable to load any web pages
from the Internet:
•
Your computer might not recognize any DNS server addresses.
A DNS server is a host on the Internet that translates Internet names (such as www
addresses) to numeric IP addresses. Typically, your ISP provides the addresses of one or
two DNS servers for your use. If you entered a DNS address during the router’s
configuration, reboot your computer, and verify the DNS address. You can configure your
computer manually with DNS addresses, as explained in your operating system
documentation.
•
Your computer might not have the router configured as its TCP/IP gateway.
If your computer obtains its information from the router by DHCP, reboot the computer,
and verify the gateway address.
•
You might be running login software that is no longer needed.
If your ISP provided a program to log you in to the Internet (such as WinPoET), you no
longer need to run that software after installing your router. You might need to go to
Internet Explorer and select Tools > Internet Options, click the Connections tab, and
select Never dial a connection.
Troubleshooting
122
R6200v2 Smart WiFi Router
Troubleshoot PPPoE
If you are using PPPoE, try troubleshooting your Internet connection.

To troubleshoot a PPPoE connection:
1. Select Administration > Router Status.
2. Click Connection Status.
3. Check the Connection Status display to see if your PPPoE connection is up and working.
4. If any of the field s on the Connection Status screen indicate Failed, you can attempt to
reconnect by clicking Connect. The router continues to attempt to connect indefinitely.
5. If you cannot connect after several minutes, you might be using an incorrect service name,
user name, or password. There might also be a provisioning problem with your ISP.
Note: Unless you connect manually, the router does not authenticate using
PPPoE until data is transmitted to the network.
Troubleshoot Internet Browsing
If your router can obtain an IP address but your computer is unable to load any web pages
from the Internet, check the following:
•
Your computer might not recognize any DNS server addresses. A DNS server is a host
on the Internet that translates Internet names (such as www addresses) to numeric IP
addresses.
Typically, your ISP provides the addresses of one or two DNS servers for your use. If you
entered a DNS address during the router’s configuration, restart your computer.
Alternatively, you can configure your computer manually with a DNS address, as
explained in the documentation for your computer.
•
Your computer might not have the router configured as its default gateway.
Reboot the computer and verify that the router address (www.routerlogin.net) is listed by
your computer as the default gateway address.
•
You might be running login software that is no longer needed. If your ISP provided a
program to log you in to the Internet (such as WinPoET), you no longer need to run that
software after installing your router. You might need to go to Internet Explorer and select
Tools > Internet Options, click the Connections tab, and select Never dial a
connection.
Troubleshooting
123
R6200v2 Smart WiFi Router
Changes Not Saved
If the router does not save the changes you make in the router interface, check the following:
•
When entering configuration settings, always click the Apply button before moving to
another screen or tab, or your changes are lost.
•
Click the Refresh or Reload button in the web browser. The changes might have
occurred, but the old settings might be in the web browser’s cache.
Wireless Connectivity
If you are having trouble connecting wirelessly to the router, try to isolate the problem.
•
Does the wireless device or computer that you are using find your wireless network?
If not, check the WiFi LED on the front of the router. If it is off, you can press the WiFi
On/Off button on the side of the router to turn the router wireless radios back on.
If you disabled the router’s SSID broadcast, then your wireless network is hidden and
does not show up in your wireless client’s scanning list. (By default, SSID broadcast is
enabled.)
•
Does your wireless device support the security that you are using for your wireless
network (WPA or WPA2)?
•
If you want to view the wireless settings for the router, use an Ethernet cable to connect a
computer to a LAN port on the router. Then log in to the router, and select Wireless see
(Basic Wireless Settings on page 24).
Note: Be sure to click Apply if you change settings.
Wireless Signal Strength
If your wireless device finds your network, but the signal strength is weak, check these
conditions:
•
Is your router too far from your computer, or too close? Place your computer near the
router, but at least 6 feet (1.8 meters) away, and see whether the signal strength
improves.
•
Are objects between the router and your computer blocking the wireless signal?
Troubleshooting
124
R6200v2 Smart WiFi Router
Troubleshoot Your Network Using the Ping Utility
Most network devices and routers contain a ping utility that sends an echo request packet to
the designated device. The device then responds with an echo reply. You can easily
troubleshoot a network is easy using the ping utility in your computer or workstation.
Test the LAN Path to Your Router
You can ping the router from your computer to verify that the LAN path to your router is set up
correctly.

To ping the router from a Windows computer:
1. From the Windows toolbar, click Start and select Run.
2. In the field provided, type ping followed by the IP address of the router, as in this example:
ping www.routerlogin.net
3. Click OK.
You should see a message like this one:
Pinging  with 32 bytes of data
If the path is working, you see this message:
Reply from < IP address >: bytes=32 time=NN ms TTL=xxx
If the path is not working, you see this message:
Request timed out
If the path is not functioning correctly, you could have one of the following problems:
•
Wrong physical connections
For a wired connection, make sure that the numbered LAN port LED is lit for the port to
which you are connected.
Check that the appropriate LEDs are on for your network devices. If your router and
computer are connected to a separate Ethernet switch, make sure that the link LEDs are
lit for the switch ports that are connected to your computer and router.
•
Wrong network configuration
Verify that the Ethernet card driver software and TCP/IP software are both installed and
configured on your computer.
Verify that the IP address for your router and your computer are correct and that the
addresses are on the same subnet.
Troubleshooting
125
R6200v2 Smart WiFi Router
Test the Path from Your Computer to a Remote Device
After verifying that the LAN path works correctly, test the path from your computer to a remote
device.
1. From the Windows toolbar, click the Start button and select Run.
2. In the Windows Run window, type:
ping -n 10 
where  is the IP address of a remote device such as your ISP DNS server.
If the path is functioning correctly, replies like those shown in the previous section are
displayed.
If you do not receive replies:
•
Check that your computer has the IP address of your router listed as the default gateway.
If the IP configuration of your computer is assigned by DHCP, this information is not
visible in your computer Network Control Panel. Verify that the IP address of the router is
listed as the default gateway.
•
Check to see that the network address of your computer (the portion of the IP address
specified by the subnet mask) is different from the network address of the remote device.
•
Check that your cable or DSL modem is connected and functioning.
•
If your ISP assigned a host name to your computer, enter that host name as the account
name in the Internet Setup screen.
•
Your ISP could be rejecting the Ethernet MAC addresses of all but one of your computers.
Many broadband ISPs restrict access by allowing traffic only from the MAC address of your
broadband modem. Some ISPs additionally restrict access to the MAC address of a single
computer connected to that modem. If so, configure your router to “clone” or “spoof” the MAC
address from the authorized computer.
Troubleshooting
126
A.
Supplemental Information
This appendix covers the following topics:
•
Factory Settings
•
Technical Specifications
127
R6200v2 Smart WiFi Router
Factory Settings
You can return the router to its factory settings. Use the end of a paper clip or a similar object
to press and hold the Reset button on the back of the router for at least 7 seconds. The router
resets, and returns to the factory configuration settings shown in the following table.
Table 3. Factory default settings
Feature
Router login
Internet
connection
Local network
(LAN)
Firewall
Default behavior
User login URL
www.routerlogin.com or www.routerlogin.net
User name (case-sensitive)
admin
Login password (case-sensitive)
password
WAN MAC address
Use default hardware address
WAN MTU size
1500
Port speed
AutoSensing
LAN IP
192.168.1.1
Subnet mask
255.255.255.0
DHCP server
Enabled
DHCP range
192.168.1.2 to 192.168.1.254
Time zone
Pacific time
Time zone daylight savings time
Disabled
Allow a registrar to configure this
router
Enabled
DHCP starting IP address
192.168.1.2
DHCP ending IP address
192.168.1.254
DMZ
Disabled
Time zone
GMT for WW except NA and GR, GMT+1 for GR, GMT-8
for NA
Time zone adjusted for daylight
savings time
Disabled
SNMP
Disabled
Inbound (communications coming
in from the Internet)
Disabled (except traffic on port 80, the HTTP port)
Outbound (communications going
out to the Internet)
Enabled (all)
Source MAC filtering
Disabled
Supplemental Information
128
R6200v2 Smart WiFi Router
Table 3. Factory default settings (continued)
Feature
Wireless
Firewall
Default behavior
Wireless communication
Enabled
SSID name
See router label
Security
WPA2-PSK (AES)
Broadcast SSID
Enabled
Transmission speed
Auto*
Country/region
United States in the US; otherwise varies by region
RF channel
6 until region selected
Operating mode
Up to 145 Mbps at 2.4 GHz, 867 Mbps at 5 GHz
Inbound (communications coming
in from the Internet)
Disabled (bars all unsolicited requests)
Outbound (communications going
out to the Internet)
Enabled (all)
*. Maximum wireless signal rate derived from IEEE Standard 802.11 specifications. Actual throughput can vary.
Network conditions and environmental factors, including volume of network traffic, building materials and
construction, and network overhead, lower actual data throughput rate.
Supplemental Information
129
R6200v2 Smart WiFi Router
Technical Specifications
Table 4. R6200v2 Router specifications
Feature
Description
Data and routing protocols
TCP/IP, RIP-1, RIP-2, DHCP, PPPoE, PPTP, Bigpond, Dynamic DNS, UPnP,
and SMB
Power adapter
•
•
•
•
Dimensions
Dimensions: 1195 x 199 x 65 mm (7.68 x 7.83 x 2.56 in.)
Weight
Weight: 417g (0.91 lbs)
Operating temperature
0° to 40° C (32º to 104º F)
Operating humidity
90% maximum relative humidity, noncondensing
Electromagnetic emissions
FCC Part 15 Class B
VCCI Class B
EN 55 022 (CISPR 22), Class B C-Tick N10947
LAN
10BASE-T or 100BASE-Tx or 1000BASE-T, RJ-45
WAN
10BASE-T or 100BASE-Tx or 1000BASE-T, RJ-45
Wireless
Maximum wireless signal rate complies with the IEEE 802.11 standard. See the
footnote for the previous table.
Radio data rates
Auto Rate Sensing
Data encoding standards
IEEE 802.11ac 2.0
IEEE 802.11n version 2.0
IEEE 802.11n, IEEE 802.11g, IEEE 802.11b 2.4 GHz
IEEE 802.11n, IEEE 802.11a 5.0 GHz
Maximum computers per
wireless network
Limited by the amount of wireless network traffic generated by each node
(typically 50–70 nodes).
Operating frequency range
2.4 GHz
2.412–2.462 GHz (US)
2.412–2.472 GHz (Japan)
2.412–2.472 GHz (Europe ETSI)
5 GHz
5.18–5.24 + 5.745–5.825 GHz (US)
5.18–5.24 GHz (Europe ETSI)
802.11 security
WPA-PSK, WPA2-PSK, and WPA/WPA2
North America: 120V, 60 Hz, input
UK, Australia: 240V, 50 Hz, input
Europe: 230V, 50 Hz, input
All regions (output): 12V DC @ 2.5A, output
Supplemental Information
130
B.
Notification of Compliance
N E T GEAR Dua l Ban d - W ir eles s
Regulatory Compliance Information
This section includes user requirements for operating this product in accordance with National laws for usage of radio
spectrum and operation of radio devices. Failure of the end-user to comply with the applicable requirements may
result in unlawful operation and adverse action against the end-user by the applicable National regulatory authority.
This product's firmware limits operation to only the channels allowed in a particular Region or Country. Therefore, all
options described in this user's guide may not be available in your version of the product.
Europe – EU Declaration of Conformity
Products bearing the
marking comply with the following EU directives:
• EMC Directive 2004/108/EC
• Low Voltage Directive 2006/95/EC
If this product has telecommunications functionality, it also complies with the requirements of the following EU
Directive:
• R&TTE Directive 1999/5/EC
Compliance with these directives implies conformity to harmonized European standards that are noted in the EU
Declaration of Conformity.
Intended for indoor use only in all EU member states, EFTA states, and Switzerland.
This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may
be limited to 10 mW EIRP in the frequency range of 2454 - 2483.5 MHz. For detailed information the end-user should
contact the national spectrum authority in France.
FCC Requirements for Operation in the United States
FCC Information to User
This product does not contain any user serviceable components and is to be used with approved antennas only.
Any product changes or modifications will invalidate all applicable regulatory certifications and approvals.
FCC Guidelines for Human Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter except in
accordance with FCC multi-transmitter product procedures.
FCC Declaration of Conformity
We, NETGEAR, Inc., 350 East Plumeria Drive, San Jose, CA 95134, declare under our sole responsibility that the
R6200v2 Smart WiFi Router complies with Part 15 Subpart B of FCC CFR47 Rules. Operation is subject to the
following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received, including interference that may cause undesired operation.
131
R6200v2 Smart WiFi Router
FCC Radio Frequency Interference Warnings & Instructions
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following methods:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an electrical outlet on a circuit different from that which the radio receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
• Any changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate this equipment.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
• For product available in the USA and Canada market, only channel 1~11 can be operated. Selection of other
channels is not possible.
• Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités.
Sélection d'autres canaux n'est pas possible.
• This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or
transmitter except in accordance with FCC multi-transmitter product procedures.
• Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une autre
antenne ou transmetteur.
• All cables used to connect peripherals must be shielded and grounded. Operation with cables connected to
peripherals that are not sheilded and grounded may result interference to radio and television reception.
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (R6200v2 Smart WiFi Router) does not exceed the Class B limits for radio-noise emissions from
digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications.
This Class [B] digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada
Industry Canada
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
IMPORTANT NOTE: Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator & your body.
Caution:
The device for the band 5150-5250 MHz is only for indoor usage to reduce po-tential for harmful interference to
co-channel mobile satellite systems.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence.
Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage
préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un
fonctionnement indésirable.
Notification of Compliance
132
R6200v2 Smart WiFi Router
NOTE IMPORTANTE: Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de
rayonnement et votre corps.
Avertissement:
Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utili-sation à l'intérieur afin
de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.
Interference Reduction Table
The following table shows the recommended minimum distance between NETGEAR equipment and household
appliances to reduce interference (in feet and meters).
Household Appliance
Recommended Minimum Distance
(in feet and meters)
Microwave ovens
30 feet / 9 meters
Baby Monitor - Analog
20 feet / 6 meters
Baby Monitor - Digital
40 feet / 12 meters
Cordless phone - Analog
20 feet / 6 meters
Cordless phone - Digital
30 feet / 9 meters
Bluetooth devices
20 feet / 6 meters
ZigBee
20 feet / 6 meters
Notification of Compliance
133

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Author                          : NETGEAR, Inc.
Create Date                     : 2013:05:30 07:45:24Z
Keywords                        : NETGEAR, R6300v2, Smart, WiFi, Router, User, Manual
Modify Date                     : 2013:06:04 20:10:57+08:00
Subject                         : R6300v2 Smart WiFi Router
Language                        : en
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Creator Tool                    : FrameMaker 10.0.2
Metadata Date                   : 2013:06:04 20:10:57+08:00
Format                          : application/pdf
Description                     : R6300v2 Smart WiFi Router
Title                           : R6300v2 Smart WiFi Router User Manual
Creator                         : NETGEAR, Inc.
Producer                        : Acrobat Distiller 9.5.5 (Windows)
Copyright                       : ?2013
Document ID                     : uuid:9dd271d4-c814-4643-adfe-f16834539d3d
Instance ID                     : uuid:f7f23bed-8dc4-46e7-9a77-4863dbc7d44e
Page Mode                       : UseOutlines
Page Count                      : 133

EXIF Metadata provided by EXIF.tools