Netgear orporated 14200281 Outdoor High Power Wireless N Access Point User Manual

Netgear Incorporated Outdoor High Power Wireless N Access Point

a href="https://usermanual.wiki/Netgear-orporated" itemprop="url"> Netgear orporated >

Contents

User Manual.pdf

InstallationNETGEAR Outdoor High Power Wireless N Access PointWND930Set Up the Access PointBefore mounting the access point in a high location, first set up and test the unit to verify wireless network connectivity.Note: The access point has a DHCP client enabled by default. If a DHCP server exists in your network, the access point obtains an IP address from the DHCP server. If a DHCP server is not detected in your network aer 30 seconds, the access point sets its IP address to a static IP address of 192.168.0.100. ¾To cable your access point:1. Using an Ethernet cable, connect a power sourcing equipment (PSE) to a PoE port on the access point.Note: You must supply either AT power to at least one LAN port or AF power to two LAN ports to power the access point. You must supply AT power to both LAN ports to receive PoE power out.2. If a DHCP server is not connected to your network, configure a computer with a static IP address of 192.168.0.210 and a subnet mask of 255.255.255.0.3. Connect an Ethernet cable from a LAN port on the access point to a LAN port on the PC.4. Check the LEDs to verify that the access point is set up correctly.Package ContentsUnpack the box and verify the contents:• Outdoor High Power Wireless N Access Point• Wall mounting bracket• Four bracket screws• Two pole mount clamps• Three weatherproof cable glands LED DescriptionPower LED •O. Power is o.•Solid green. Power is on.•Amber, then blinking green. A self-test is running or soware is being loaded. During startup, the LED is first steady amber, then goes o, and then blinks green before turning steady green aer about 45 seconds. If aer one minute the LED remains amber or continues to blink green, it indicates a system fault.Activity LED •O. There is no network trac through the access point.•Blinking green. There is network trac through the access point.2.4G WLAN LED•O. The wireless interface is o.•Solid green. The wireless interface is on.•Blinking green. Wireless activity is detected on the 2.4G band.5G WLAN LED •O. The wireless interface is o.•Solid green. The wireless interface is on.•Blinking green. Wireless activity is detected on the 5G band.Heater LED •O. Heater is o.•Solid green. Heater is on.LAN port LEDs •O. No link is detected.•Solid green. Link is detected.•Solid amber. 10/100/1000 speed connection is detected.•Blinking amber. 10/100/1000 speed activity is detected. ¾To configure your access point for your network:1. Connect to the access point by opening your browser and entering the access point’s IP addressIf a DHCP server is not installed in your network, the default IP address is 192.168.0.100.A login window displays.2. Enter admin for the user name and password for the password, both in lower case letters.The access point user interface displays.3. Select Configuration > System > Basic > General from the menu.Operation temperature : -20℃ to +60℃ Operation voltage: Input: 44-57Vdc, 0.45A (per each PoE In) Output: 51Vdc, 15.4W
August 2014NETGEAR, Inc.350 East Plumeria DriveSan Jose, CA 95134, USANETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change without notice. © NETGEAR, Inc. All rights reserved.4. Complete the Access Point Name field and select your Country/Region of operation from the drop-down list.5. Select Configuration > IP > IP Settings from the menu and configure the IP settings for your network.Note: If you use DHCP, reserve an IP address (based on the access point’s MAC address) on the DHCP server. You can then use that address to log in to the access point.6. Select Configuration > Wireless > Basic > Wireless Settings and configure the wireless settings for your network.For more information about wireless settings, see the reference manual.7. Select Configuration > Security > Profile Settings and configure security profiles for your network.For more information about security profile settings, see the reference manual.Deploy the Access PointThe best location for your access point is elevated such as wall or ceiling mounted, at the center of your wireless coverage area, and within line of sight of all mobile devices. ¾To deploy your access point:1. Disconnect your access point and position it where you will deploy it.2. Connect an ethernet cable from your access point to a LAN port on your router, switch or hub.3. Connect a power sourcing equipment (PSE) to one of the PoE ports on the access point. If your router switch or hub supplies PoE, skip this step.Note: You must supply either AT power to at least one LAN port or AF power to two LAN ports to power the access point. You must supply AT power to both LAN ports to receive PoE power out.4. Using a wireless device, verify connectivity by using a browser to connect to the Internet.Problem Cause Possible SolutionYou cannot access the Internet or the LAN from a wireless device.A configuration problem exists.•Make sure that the SSID and wireless security settings of the wireless device are the same as those of the access point.•ThewirelessdevicemightnothavethecorrectTCP/IPsettings to communicate with the network. Restart the wireless device and check that TCP/IP is set up correctly for that network.•Theaccesspointdefaultvaluesmightnotworkwith your network. Check the access point default configuration against the configuration of other devices in your network. For information about changing the default values of the access point, see the reference manual.SupportThank you for selecting NETGEAR products. Aer installing your device, locate the serial number on the label of your product and use it to register your product at https://my.netgear.com. You must register your product before you can use NETGEAR telephone support. NETGEAR recommends registering your product through the NETGEAR website. For product updates and web support, visit http://support.netgear.com.NETGEAR recommends that you use only the ocial NETGEAR support resources.For the current EU Declaration of Conformity, visit http://support.netgear.com/app/answers/detail/a_id/11621/.For regulatory compliance information, visit http://www.netgear.com/about/regulatory/.See the regulatory compliance document before connecting the power supply.Optional External AntennasThe WND930 supports optional external antennas. ¾To install optional external 2G or 5G antennas:1. Attach the 2G or 5G antennas to the corresponding connectors on the side panels of the access point.2. Log into the access point and configure it to use the external antennas.Troubleshooting TipsThis section provides some tips for correcting simple problems that you might encounter. For more troubleshooting information, see the troubleshooting chapter in the reference manual.Problem Cause Possible SolutionNo LEDs are lit on the access point.The access point has no power.•Makesurethatapowersourceequipment(PSE)isconnected via Ethernet to at least one PoE port.•Make sure that the power source equipment (PSE) is powered on.The LAN LED is o.A hardware connection problem exists.•Makesurethatthecableconnectorsaresecurelyplugged into the access point and to the network switch. Make sure that the network switch is turned on.The Wireless LED is o.The wireless connection does not work.•Makesurethepowereddeviceisprovidingsucientpower to the access point.•Logintotheaccesspointandverifythattheradioorradios are turned on.•ContactNETGEARiftheWirelessLEDremainso.You cannot configure the access point from a browser.Multiple possible causes.•Make sure that the access point is correctly installed, it is powered on, and that the LAN LED is lit.•MakesurethatyourcomputerisusinganIPaddressin the same range as the access point. The access point default IP address is 192.168.0.100, and the default subnet mask is 255.255.255.0.•Quitthebrowser,clearthecache,deletethecookies,and launch the browser again.
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For operation within 5.15 ~ 5.25GHz / 5.47 ~5.725GHz frequency range, it is restricted to indoor environment. The band from 5600-5650MHz will be disabled by the software during the manufacturing and cannot be changed by the end user. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. Radiation Exposure Statement:
Download:
Mirror Download [FCC.gov]
Document ID2371575
Application IDiXcoBdIFzWOhaXz55tAMcA==
Document DescriptionUser Manual.pdf
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize87.93kB (1099130 bits)
Date Submitted2014-08-28 00:00:00
Date Available2015-02-24 00:00:00
Creation Date2014-08-07 16:49:56
Producing SoftwareAdobe PDF Library 10.0.1
Document Lastmod2014-08-21 09:52:14
Document TitleNETGEAR ProSAFE Outdoor High Power Wireless N Access Point WND930 Installation Guide
Document CreatorAdobe InDesign CS6 (Windows)
Document Author: NETGEAR
FCC ID Filing: PY314200281

Navigation menu