Netgear orporated DG834GT 108 Mbps Super Wireless ADSL Router User Manual FullManual

Netgear Incorporated 108 Mbps Super Wireless ADSL Router FullManual

Users Manual

August 2004202-10053-01 REFGDAugust 2004NETGEAR, Inc.4500 Great America Parkway Santa Clara, CA 95054 USAPhone 1-888-NETGEARReference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router
iiAugust 2004© 2004 by NETGEAR, Inc. All rights reserved. August 2004. TrademarksNETGEAR is a trademark of Netgear, Inc. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation.Other brand and product names are registered trademarks or trademarks of their respective holders.Statement of ConditionsIn the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice.NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.Federal Communications Commission (FCC) Compliance Notice: Radio Frequency NoticeThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help. Federal Communications Commission (FCC) Radiation Exposure StatementThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation.EN 55 022 Declaration of ConformanceThis is to certify that the DG834GT 108 Mbps Super Wireless ADSL Router is shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN 55 022 Class B (CISPR 22).
August 2004iiiBestätigung des Herstellers/ImporteursEs wird hiermit bestätigt, daß das DG834GT 108 Mbps Super Wireless ADSL Router gemäß der im BMPT-AmtsblVfg 243/1991 und Vfg 46/1992 aufgeführten Bestimmungen entstört ist. Das vorschriftsmäßige Betreiben einiger Geräte (z.B. Testsender) kann jedoch gewissen Beschränkungen unterliegen. Lesen Sie dazu bitte die Anmerkungen in der Betriebsanleitung.Das Bundesamt für Zulassungen in der Telekommunikation wurde davon unterrichtet, daß dieses Gerät auf den Markt gebracht wurde und es ist berechtigt, die Serie auf die Erfüllung der Vorschriften hin zu überprüfen.Certificate of the Manufacturer/ImporterIt is hereby certified that the DG834GT 108 Mbps Super Wireless ADSL Router has been suppressed in accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in accordance with the regulations may, however, be subject to certain restrictions. Please refer to the notes in the operating instructions. Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and has been granted the right to test the series for compliance with the regulations. Voluntary Control Council for Interference (VCCI) StatementThis equipment is in the second category (information equipment to be used in a residential area or an adjacent area thereto) and conforms to the standards set by the Voluntary Control Council for Interference by Data Processing Equipment and Electronic Office Machines aimed at preventing radio interference in such residential areas.When used near a radio or TV receiver, it may become the cause of radio interference. Read instructions for correct handling.Customer SupportRefer to the Support Information Card that shipped with your DG834GT 108 Mbps Super Wireless ADSL Router.World Wide WebNETGEAR maintains a World Wide Web home page that you can access at the universal resource locator (URL) http://www.netgear.com. A direct connection to the Internet and a Web browser such as Internet Explorer or Netscape are required.FCC Caution :To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices).FCC Radiation Exposure StatementThis equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.Warning!To meet FCC and other national safety guidelines for RF exposure, the antennas for this device must be installed to ensure a minimum separation distance of 20cm (7.9 in.) from persons.Further, the antennas shall not be colocated with other antenna or radio transmitter.
August 2004iv
Contents vAugust 2004ContentsChapter 1 About This GuideAudience, Conventions, Scope ......................................................................................1-1How to Use this Manual ..................................................................................................1-2How to Print this Manual .................................................................................................1-3Chapter 2 IntroductionAbout the Router ............................................................................................................2-1Key Features ..................................................................................................................2-2802.11g Wireless Networking ...................................................................................2-2A Powerful, True Firewall .........................................................................................2-3Easy Installation and Management ..........................................................................2-3Protocol Support ......................................................................................................2-4Content Filtering .......................................................................................................2-5Auto Sensing and Auto Uplink™ LAN Ethernet Connections ..................................2-5What’s in the Box? ..........................................................................................................2-6The Router’s Front Panel .........................................................................................2-6The Router’s Rear Panel .........................................................................................2-8Chapter 3 Connecting the Router to the InternetWhat You Need Before You Begin ..................................................................................3-1ADSL Microfilter Requirements ................................................................................3-1ADSL Microfilter .................................................................................................3-1ADSL Microfilter with Built-In Splitter .................................................................3-2Ethernet Cabling Requirements ...............................................................................3-2Computer Hardware Requirements .........................................................................3-2LAN Configuration Requirements ............................................................................3-2Internet Configuration Requirements .......................................................................3-3Where Do I Get the Internet Configuration Parameters? .........................................3-3
August 2004vi ContentsRecord Your Internet Connection Information ..........................................................3-3Connecting the DG834GT to Your LAN ..........................................................................3-5How to Connect the Router ......................................................................................3-5Auto-Detecting Your Internet Connection Type ............................................................3-10Wizard-Detected PPPoE Login Account Setup ......................................................3-11Wizard-Detected PPPoA Login Account Setup ......................................................3-12Wizard-Detected Dynamic IP Account Setup .........................................................3-12Wizard-Detected IP Over ATM Account Setup ......................................................3-13Wizard-Detected Fixed IP (Static) Account Setup ..................................................3-14Testing Your Internet Connection ..................................................................................3-15Manually Configuring Your Internet Connection ...........................................................3-15How to Perform Manual Configuration ...................................................................3-16Internet Connection Requires Login and Uses PPPoE ...................................3-17Internet Connection Requires Login and Uses PPPoA ...................................3-18Internet Connection Does Note Require A Login ............................................3-19ADSL Settings ........................................................................................................3-20Chapter 4 Wireless ConfigurationConsiderations for a Wireless Network ..........................................................................4-1Observe Performance, Placement, and Range Guidelines .....................................4-1Implement Appropriate Wireless Security ................................................................4-2Understanding Wireless Settings ...................................................................................4-3How to Set Up and Test Basic Wireless Connectivity ..............................................4-7How to Restricting Wireless Access to Your Network ..............................................4-8Restricting Access to Your Network by Turning Off Wireless Connectivity ........4-9Restricting Wireless Access Based on the Wireless Network Name (SSID) .....4-9Restricting Wireless Access Based on the Wireless Station Access List ..........4-9Choosing WEP Authentication and Security Encryption Methods ......................... 4-11Authentication Type Selection .........................................................................4-11Encryption Choices ..........................................................................................4-12How to Configure WEP ..........................................................................................4-13How to Configure WPA-PSK ..................................................................................4-14Chapter 5 Protecting Your NetworkProtecting Access to Your DG834GT 108 Mbps Super Wireless ADSL Router .............5-1
Contents viiAugust 2004How to Change the Built-In Password .....................................................................5-1Changing the Administrator Login Timeout ..............................................................5-2Configuring Basic Firewall Services ...............................................................................5-2Blocking Keywords, Sites, and Services ..................................................................5-3How to Block Keywords and Sites ...........................................................................5-3Firewall Rules .................................................................................................................5-5Inbound Rules (Port Forwarding) .............................................................................5-6Inbound Rule Example: A Local Public Web Server ..........................................5-6Inbound Rule Example: Allowing Videoconferencing ........................................5-8Considerations for Inbound Rules .....................................................................5-9Outbound Rules (Service Blocking) .........................................................................5-9Outbound Rule Example: Blocking Instant Messenger ...................................5-10Order of Precedence for Rules .............................................................................. 5-11Services ........................................................................................................................5-12How to Define Services ..........................................................................................5-13Setting Times and Scheduling Firewall Services ..........................................................5-14How to Set Your Time Zone ...................................................................................5-14How to Schedule Firewall Services ........................................................................5-15Chapter 6 Managing Your NetworkBacking Up, Restoring, or Erasing Your Settings ...........................................................6-1How to Back Up the Configuration to a File .............................................................6-1How to Restore the Configuration from a File ..........................................................6-2How to Erase the Configuration ...............................................................................6-2Upgrading the Router’s Firmware ...................................................................................6-2How to Upgrade the Router Firmware .....................................................................6-3Network Management Information .................................................................................6-4Viewing Router Status and Usage Statistics ............................................................6-4Viewing Attached Devices ........................................................................................6-9Viewing, Selecting, and Saving Logged Information ................................................6-9Selecting What Information to Log ..................................................................6-11Saving Log Files on a Server ..........................................................................6-12Examples of Log Messages ...................................................................................6-12Activation and Administration ..........................................................................6-12Dropped Packets .............................................................................................6-12
August 2004viii ContentsEnabling Security Event E-mail Notification .................................................................6-13Running Diagnostic Utilities and Rebooting the Router ................................................6-14Enabling Remote Management ....................................................................................6-15Configuring Remote Management .........................................................................6-15Chapter 7 Advanced ConfigurationConfiguring Advanced Security ......................................................................................7-1Setting Up A Default DMZ Server ............................................................................7-1How to Configure a Default DMZ Server ...........................................................7-2Connect Automatically, as Required ........................................................................7-3Disable Port Scan and DOS Protection ...................................................................7-3Respond to Ping on Internet WAN Port ...................................................................7-3MTU Size .................................................................................................................7-3Configuring LAN IP Settings ...........................................................................................7-3DHCP .......................................................................................................................7-5Use Router as DHCP server .............................................................................7-5Reserved IP addresses .....................................................................................7-6How to Configure LAN TCP/IP Settings ...................................................................7-7Configuring Dynamic DNS .......................................................................................7-7How to Configure Dynamic DNS ..............................................................................7-8Using Static Routes ........................................................................................................7-9Static Route Example ...............................................................................................7-9How to Configure Static Routes .............................................................................7-10Chapter 8 TroubleshootingBasic Functioning ...........................................................................................................8-1Power LED Not On ...................................................................................................8-2Test LED Never Turns On or Test LED Stays On .....................................................8-2LAN or WAN Port LEDs Not On ...............................................................................8-2Troubleshooting the Web Configuration Interface ..........................................................8-3Troubleshooting the ISP Connection ..............................................................................8-4ADSL link .................................................................................................................8-4WAN LED Blinking Yellow ..................................................................................8-4WAN LED Off .....................................................................................................8-4Obtaining a WAN IP Address ...................................................................................8-5
Contents ixAugust 2004Troubleshooting PPPoE or PPPoA ..........................................................................8-6Troubleshooting Internet Browsing ..........................................................................8-6Troubleshooting a TCP/IP Network Using the Ping Utility ..............................................8-7Testing the LAN Path to Your Router .......................................................................8-7Testing the Path from Your Computer to a Remote Device .....................................8-8Restoring the Default Configuration and Password ........................................................8-9Using the Reset button .............................................................................................8-9Problems with Date and Time .........................................................................................8-9Appendix A Technical SpecificationsAppendix B Network and Routing BasicsRelated Publications ...................................................................................................... B-1Basic Router Concepts .................................................................................................. B-1What is a Router? ................................................................................................... B-1Routing Information Protocol ................................................................................... B-2IP Addresses and the Internet ................................................................................. B-2Netmask .................................................................................................................. B-4Subnet Addressing .................................................................................................. B-4Private IP Addresses ............................................................................................... B-7Single IP Address Operation Using NAT ................................................................. B-7MAC Addresses and Address Resolution Protocol ................................................. B-8Related Documents ................................................................................................. B-9Domain Name Server .............................................................................................. B-9IP Configuration by DHCP ...................................................................................... B-9Internet Security and Firewalls .................................................................................... B-10What is a Firewall? ................................................................................................ B-10Stateful Packet Inspection ..................................................................................... B-10Denial of Service Attack .........................................................................................B-11Ethernet Cabling ...........................................................................................................B-11Category 5 Cable Quality .......................................................................................B-11Inside Twisted Pair Cables .................................................................................... B-12Uplink Switches, Crossover Cables, and MDI/MDIX Switching ............................ B-13
August 2004xContentsAppendix C Preparing Your NetworkPreparing Your Computers for TCP/IP Networking ....................................................... C-1Configuring Windows 95, 98, and Me for TCP/IP Networking ....................................... C-2Installing or Verifying Windows Networking Components ....................................... C-2Enabling DHCP to Automatically Configure TCP/IP Settings in Windows 95B, 98, and Me C-4Selecting the Windows’ Internet Access Method .................................................... C-6Verifying TCP/IP Properties .................................................................................... C-6Configuring Windows NT4, 2000 or XP for IP Networking ............................................ C-7Installing or Verifying Windows Networking Components ....................................... C-7DHCP Configuration of TCP/IP in Windows XP, 2000, or NT4 ...................................... C-8DHCP Configuration of TCP/IP in Windows XP ..................................................... C-8DHCP Configuration of TCP/IP in Windows 2000 ................................................ C-10DHCP Configuration of TCP/IP in Windows NT4 .................................................. C-13Verifying TCP/IP Properties for Windows XP, 2000, and NT4 .............................. C-15Configuring the Macintosh for TCP/IP Networking ...................................................... C-16MacOS 8.6 or 9.x .................................................................................................. C-16MacOS X ............................................................................................................... C-16Verifying TCP/IP Properties for Macintosh Computers ......................................... C-17Verifying the Readiness of Your Internet Account ....................................................... C-18Are Login Protocols Used? ................................................................................... C-18What Is Your Configuration Information? .............................................................. C-18Obtaining ISP Configuration Information for Windows Computers ....................... C-19Obtaining ISP Configuration Information for Macintosh Computers ..................... C-20Restarting the Network ................................................................................................ C-21Appendix D Wireless Networking BasicsWireless Networking Overview ...................................................................................... D-1Infrastructure Mode ................................................................................................. D-1Ad Hoc Mode (Peer-to-Peer Workgroup) ................................................................ D-2Network Name: Extended Service Set Identification (ESSID) ................................ D-2Authentication and WEP Data Encryption ..................................................................... D-2802.11 Authentication .............................................................................................. D-3Open System Authentication ................................................................................... D-3Shared Key Authentication ...................................................................................... D-4
Contents xiAugust 2004Overview of WEP Parameters ................................................................................ D-5Key Size .................................................................................................................. D-6WEP Configuration Options .................................................................................... D-7Wireless Channels ......................................................................................................... D-7WPA Wireless Security .................................................................................................. D-8How Does WPA Compare to WEP? ........................................................................ D-9How Does WPA Compare to IEEE 802.11i? ........................................................ D-10What are the Key Features of WPA Security? ...................................................... D-10WPA Authentication: Enterprise-level User Authentication via 802.1x/EAP and RADIUS .................................................. D-12WPA Data Encryption Key Management ........................................................ D-14Is WPA Perfect? .................................................................................................... D-16Product Support for WPA ...................................................................................... D-16Supporting a Mixture of WPA and WEP Wireless Clients is Discouraged ...... D-16Changes to Wireless Access Points ............................................................... D-16Changes to Wireless Network Adapters ......................................................... D-17Changes to Wireless Client Programs ............................................................ D-18 Glossary
August 2004xii Contents
About This Guide 1-1August 2004Chapter 1 About This GuideThank you for purchasing the NETGEAR™ DG834GT 108 Mbps Super Wireless ADSL Router.Audience, Conventions, Scope This reference manual assumes that the reader has basic-to-intermediate computer and Internet skills. However, basic computer network, Internet, firewall, and networking technology tutorial information is provided in the Appendices.This guide uses the following typographical conventions:This manual is written for the DG834GT Super Wireless ADSL Router according to these specifications:Table 1. Typographical conventionsitalics Emphasis, books, CDs, URL namesbold User inputmono space Screen text, file and server names, extensions, commands, IP addressesNote: This format is used to highlight information of importance or special interest.Table 1-1. Manual SpecificationsProduct Version DG834GT 108 Mbps Super Wireless ADSL RouterManual Publication Date August 2004Note: Product updates are available on the NETGEAR, Inc. Web site at http://kbserver.netgear.com/DG834GT.asp.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router1-2 About This GuideAugust 2004How to Use this ManualThe HTML version of this manual includes these features.Figure 1 -1: HTML version of this manual1. Left pane. Use the left pane to view the Contents, Index, Search, and Favorites tabs. To view the HTML version of the manual, you must have a version 4 or later browser with JavaScript enabled.2. Toolbar buttons. Use the toolbar buttons across the top to navigate, print pages, and more.–The Show in Contents button locates the current topic in the Contents tab.–Previous/Next buttons display the previous or next topic.–The PDF button links to a PDF version of the full manual.–The Print button prints the current topic. Using this button when a step-by-step procedure is displayed will send the entire procedure to your printer–you do not have to worry about specifying the correct range of pages.3. Right pane. Use the right pane to view the contents of the manual. Also, each page of the manual includes a link at the top right which links to a PDF file containing just the currently selected chapter of the manual.123
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterAbout This Guide 1-3August 2004How to Print this ManualTo print this manual you can choose one of the following several options, according to your needs.•Printing a “How To” Sequence of Steps in the HTML View. Use the Print button on the upper right of the toolbar to print the currently displayed topic. Using this button when a step-by-step procedure is displayed will send the entire procedure to your printer–you do not have to worry about specifying the correct range of pages. •Printing a Chapter. Use the link at the top right of any page.– Click “PDF of This Chapter” link at the top right of any page in the chapter you want to print. A new browser window opens showing the PDF version of the chapter you were viewing. – Click the print icon in the upper left of the window. –Tip: If your printer supports printing two pages on a single sheet of paper, you can save paper and printer ink by selecting this feature.•Printing the Full Manual. Use the PDF button in the toolbar at the top right of the browser window.– Click PDF button. A new browser window opens showing the PDF version of the chapter you were viewing. – Click the print icon in the upper left of the window. –Tip: If your printer supports printing two pages on a single sheet of paper, you can save paper and printer ink by selecting this feature.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router1-4 About This GuideAugust 2004
Introduction 2-1August 2004Chapter 2IntroductionThis chapter describes the features of the NETGEAR DG834GT 108 Mbps Super Wireless ADSL Router. The DG834GT Super Wireless ADSL Router is a combination of a built-in ADSL modem, router, 4-port switch, firewall, and up to 108 Mbps wireless access point that enables your entire network to safely share an Internet connection that otherwise is used by a single computer.About the RouterThe DG834GT 108 Mbps Super Wireless ADSL Router provides continuous, high-speed 10/100 Ethernet access between your Ethernet devices. The DG834GT Super Wireless ADSL Router enables your entire network to share an Internet connection through the built-in ADSL modem that otherwise is used by a single computer. With minimum setup, you can install and use the router within minutes.The DG834GT Super Wireless ADSL Router provides multiple Web content filtering options, plus e-mail browsing activity, reporting, and instant alerts. Parents and network administrators can establish restricted access policies based on time of day, Web site addresses, and address keywords. They can also share high-speed ADSL Internet access for up to 253 personal computers. The included firewall and Network Address Translation (NAT) features protect you from hackers.Note: If you are unfamiliar with networking and routing, refer to Appendix B, “Network and Routing Basics” to become more familiar with the terms and procedures used in this manual.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router2-2 IntroductionAugust 2004Key FeaturesThe DG834GT Super Wireless ADSL Router provides the following features:• 802.11g wireless networking, with the ability to operate in Auto 108 Mbps mode, 108 Mbps “turbo-g” only, the 802.11b+g modes, 802.11g-only, and 802.11b-only. • A built-in ADSL modem• A powerful, true firewall• Easy, Web-based setup for installation and management• Extensive Internet protocol support• Content filtering• Auto Sensing and Auto Uplink™ LAN Ethernet connectionsThese features are discussed below.802.11g Wireless NetworkingThe DG834GT Super Wireless ADSL Router includes an 802.11g wireless access point, providing continuous, high-speed 54 Mbps access between your wireless and Ethernet devices. The access point provides:• 802.11g wireless networking at up to 108 Mbps.• 802.11g wireless networking, with the ability to operate in the following modes, thus providing backwards compatibility with 802.11b devices or dedicating the wireless network to the higher bandwidth 802.11g or 108 Mbps only devices:— Auto 108 Mbps mode (i.e., all 802.11g, 802.11b, and Netgear 108 Mbps wireless stations can be used; this mode is the second fastest mode)— 108 Mbps only (fastest)Note: Only use the 108 Mbps only mode when all wireless adapters in your open network bear the 108 Mbps logo.Figure 2-1: 108 Mbps Logo10 8
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterIntroduction 2-3August 2004— 802.11b+g modes— 802.11g-only— 802.11b-only• 64-bit and 128-bit WEP encryption security.• WEP keys can be generated manually or by passphrase.• Wireless access can be restricted by MAC address.• Wireless network name broadcast can be turned off so that only devices that have the network name (SSID) can connect.A Powerful, True FirewallUnlike simple Internet sharing NAT routers, the DG834GT is a true firewall, using stateful packet inspection to defend against hacker attacks. Its firewall features include:• Denial of Service (DoS) protection Automatically detects and thwarts Denial of Service (DoS) attacks such as Ping of Death, SYN Flood, LAND Attack and IP Spoofing.• Blocks unwanted traffic from the Internet to your LAN.• Blocks access from your LAN to Internet locations or services that you specify as off-limits.• Logs security incidents The DG834GT will log security events such as blocked incoming traffic, port scans, attacks, and administrator logins. You can configure the router to email the log to you at specified intervals. You can also configure the router to send immediate alert messages to your email address or email pager whenever a significant event occurs.Easy Installation and ManagementYou can install, configure, and operate the DG834GT within minutes after connecting it to the network. The following features simplify installation and management tasks:• Browser-based management Browser-based configuration allows you to easily configure your router from almost any type of personal computer, such as Windows, Macintosh, or Linux. A user-friendly Setup Wizard is provided and online help documentation is built into the browser-based Web Management Interface.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router2-4 IntroductionAugust 2004• Smart Wizard The router automatically senses the type of Internet connection, asking you only for the information required for your type of ISP account.• Remote management The router allows you to log in to the Web management interface from a remote location via the Internet. For security, you can limit remote management access to a specified remote IP address or range of addresses, and you can choose a nonstandard port number.• Diagnostic functions The router incorporates built-in diagnostic functions such as Ping, DNS lookup, and remote reboot. These functions allow you to test Internet connectivity and reboot the router. You can use these diagnostic functions directly from the DG834GT when you are connected on the LAN or when you are connected over the Internet via the remote management function.• Visual monitoring The router’s front panel LEDs provide an easy way to monitor its status and activity.• Flash erasable programmable read-only memory (EPROM) for firmware upgrades.Protocol SupportThe DG834GT supports Transmission Control Protocol/Internet Protocol (TCP/IP) and Routing Information Protocol (RIP). Appendix B, “Network and Routing Basics” provides further information on TCP/IP.• The Ability to Enable or Disable IP Address Sharing by NAT The DG834GT allows several networked PCs to share an Internet account using only a single IP address, which may be statically or dynamically assigned by your Internet service provider (ISP). This technique, known as Network Address Translation (NAT), allows the use of an inexpensive single-user ISP account. This feature can also be turned off completely while using the DG834GT if you want to manage the IP address scheme yourself.• Automatic Configuration of Attached PCs by DHCP The DG834GT dynamically assigns network configuration information, including IP, router, and domain name server (DNS) addresses, to attached PCs on the LAN using the Dynamic Host Configuration Protocol (DHCP). This feature greatly simplifies configuration of PCs on your local network.• DNS Proxy When DHCP is enabled and no DNS addresses are specified, the router provides its own address as a DNS server to the attached PCs. The router obtains actual DNS addresses from the ISP during connection setup and forwards DNS requests from the LAN.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterIntroduction 2-5August 2004• Classical IP (RFC 1577) Some Internet service providers, in Europe for example, use Classical IP in their ADSL services. In such cases, the router is able to use the Classical IP address from the ISP.• PPP over Ethernet (PPPoE) PPP over Ethernet is a protocol for connecting remote hosts to the Internet over an ADSL connection by simulating a dial-up connection. This feature eliminates the need to run a login program such as EnterNet or WinPOET on your computer.• PPP over ATM (PPPoA) PPP over ATM is a protocol for connecting remote hosts to the Internet over an ADSL connection by simulating an ATM connection. • Dynamic DNS Dynamic DNS services allow remote users to find your network using a domain name when your IP address is not permanently assigned. The router contains a client that can connect to many popular Dynamic DNS services to register your dynamic IP address.• Universal Plug and Play (UPnP) UPnP is a networking architecture that provides compatibility between networking technologies. UPnP compliant routers provide broadband users at home and small businesses with a seamless way to participate in online games, videoconferencing and other peer-to-peer services. Content FilteringWith its content filtering feature, the DG834GT prevents objectionable content from reaching your PCs. The router allows you to control access to Internet content by screening for keywords within Web addresses. You can configure the router to log and report attempts to access objectionable Internet sites.Auto Sensing and Auto Uplink™ LAN Ethernet ConnectionsWith its internal 4-port 10/100 switch, the DG834GT can connect to either a 10 Mbps standard Ethernet network or a 100 Mbps Fast Ethernet network. The local LAN ports are autosensing and capable of full-duplex or half-duplex operation.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router2-6 IntroductionAugust 2004The router incorporates Auto UplinkTM technology. Each local Ethernet port will automatically sense whether the Ethernet cable plugged into the port should have a ‘normal’ connection such as to a computer or an ‘uplink’ connection such as to a switch or hub. That port will then configure itself to the correct configuration. This feature also eliminates the need to worry about crossover cables, as Auto Uplink will accommodate either type of cable to make the right connection.What’s in the Box?The product package should contain the following items:• DG834GT 108 Mbps Super Wireless ADSL Router• AC power adapter (varies by region)• Category 5 (Cat 5) Ethernet cable• Telephone cable• Microfilters (quantity and type vary by region)•108 Mbps Super Wireless ADSL Router Resource CD, including:—This guide— Application Notes• A printed Quick Installation Guide• Warranty and Support Information cardsIf any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the carton, including the original packing materials, in case you need to return the product for repair.The Router’s Front PanelThe DG834GT 108 Mbps Super Wireless ADSL Router front panel shown below contains status LEDs.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterIntroduction 2-7August 2004Figure 2-2: DG834GT Front PanelYou can use the LEDs to verify various conditions. Table 2-1 lists and describes each LED on the front panel of the router. These LEDs are green when lit.Power Test InternetWireless LAN
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router2-8 IntroductionAugust 2004The Router’s Rear PanelThe rear panel of the DG834GT 108 Mbps Super Wireless ADSL Router (Figure 2-3) contains port connections.Table 2-1. LED Descriptions Label Activity DescriptionPower OnOff Power is supplied to the router.Power is not supplied to the router.Test OnOff The system is initializing.The system is ready and running.Wireless OnOff Indicates that the Wireless port is initialized.The Wireless Access Point is turned off. Internet Blink -- AmberOn -- GreenBlink -- GreenIndicates ADSL training.The Internet port has detected a link with an attached device.Data is being transmitted or received by the Internet port.LAN On (Green)Blink (Green)On (Amber)Blink (Amber)OffThe Local port has detected a link with a 100 Mbps device.Data is being transmitted or received at 100 Mbps.The Local port has detected a link with a 10 Mbps device.Data is being transmitted or received at 10 Mbps.No link is detected on this port.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterIntroduction 2-9August 2004Figure 2-3: DG834GT Rear PanelViewed from left to right, the rear panel contains the following elements:• ADSL port for connecting the router to an ADSL line• Four Local Ethernet RJ-45 LAN ports for connecting the router to the local computers• Factory Default Reset push button•DC power in• Wireless antennaPowerADSLWirelessLANResetInternet
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router2-10 IntroductionAugust 2004
Connecting the Router to the Internet 3-1August 2004Chapter 3 Connecting the Router to the InternetThis chapter describes how to set up the router on your Local Area Network (LAN) and connect to the Internet. It describes how to configure your DG834GT 108 Mbps Super Wireless ADSL Router for Internet access using the Setup Wizard, or how to manually configure your Internet connection.What You Need Before You BeginYou need to prepare the following before you can establish an Internet connection through your router:1. The router connected to an ADSL line and a computer properly connected to the router as explained below.2. Active Internet service such as that provided by an ADSL account.3. The Internet Service Provider (ISP) configuration information for your DSL account.Note: If you purchased the DG834GT in a country where a microfilter is not included, you must acquire one.ADSL Microfilter RequirementsADSL technology uses the same wires as your telephone service. However, ADSL adds signals to the telephone lines which create noise in the telephone service. You must use ADSL microfilters to filter out these signals before they reach your telephone. ADSL MicrofilterFigure 3-1: ADSL microfilterPhone
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router3-2 Connecting the Router to the InternetAugust 2004Each device such as a telephone, fax machine, answering machine, or caller ID display will require an ADSL microfilter.Note: Do not connect the DG834GT to the ADSL line through a microfilter unless the microfilter is a combination microfilter/splitter specifically designed for this purpose. Doing so will prevent the built-in ADSL modem in the DG834GT from establishing a connection to the Internet. If you have any doubts about this, connect the DG834GT directly to the ADSL line.ADSL Microfilter with Built-In SplitterFigure 3-2: ADSL microfilter with built-in splitter Use an ADSL microfilter with built-in splitter when there is a single wall outlet which must provide connectivity for both the DG834GT and telephone equipment.Ethernet Cabling RequirementsThe DG834GT Super Wireless ADSL Router connects to your Ethernet LAN via twisted-pair cables. If the computer will connect to your network at 100 Mbps, you must use a Category 5 (CAT5) cable such as the one provided with your router.Computer Hardware RequirementsTo use the DG834GT Super Wireless ADSL Router on your network, each computer must have an installed Ethernet adapter and an Ethernet cable, or a 802.11g wireless adapter. LAN Configuration RequirementsFor the initial connection to the Internet and configuration of your router, you need to connect a computer to the router which is set to automatically get its TCP/IP configuration from the router via DHCP.Note: Please refer to Appendix C, “Preparing Your Network” for assistance with DHCP configuration.PhoneDSLLine
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterConnecting the Router to the Internet 3-3August 2004Internet Configuration RequirementsDepending on how your ISP set up your Internet account, you need one or more of these configuration parameters to connect your router to the Internet: • Virtual Path Identifier (VPI)/Virtual Channel Indentifier (VCI) parameters• Multiplexing Method• Host and Domain Names• ISP Login Name and Password• ISP Domain Name Server (DNS) Addresses• Fixed or Static IP AddressWhere Do I Get the Internet Configuration Parameters?There are several ways you can gather the required Internet connection information.• Your ISP should have provided you with all the information needed to connect to the Internet. If you cannot locate this information, you can ask your ISP to provide it or you can try one of the options below.• If you have a computer already connected using the active Internet access account, you can gather the configuration information from that computer.• For Windows 95/98/ME, open the Network control panel, select the TCP/IP entry for the Ethernet adapter, and click Properties.• For Windows 2000/XP, open the Local Area Network Connection, select the TCP/IP entry for the Ethernet adapter, and click Properties.• For Macintosh computers, open the TCP/IP or Network control panel.• You can also refer to the DG834GT Resource CD for the NETGEAR Router ISP Guide which provides Internet connection information for many ISPs.Once you locate your Internet configuration parameters, you may want to record them on the next page.Record Your Internet Connection InformationPrint the following page. Fill in the configuration parameters from your Internet Service Provider (ISP).
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router3-4 Connecting the Router to the InternetAugust 2004ISP Multiplexing Method and Virtual Circuit Number: The default settings of your DG834GT 108 Mbps Super Wireless ADSL Router will work fine for most ISPs. However, some ISPs use a specific Multiplexing Method or a Virtual Circuit Number for either the Virtual Path Identifier (VPI) or Virtual Channel Identifier (VCI). If your ISP provided you with a specific Multiplexing Method or VPI/VCI number, then fill in the following:Multiplexing Method, circle one: LLC-based or VC-basedVPI: ________ A number between 0 and 255. VCI: ___________ A number between 1 and 65535.ISP Login Name: The login name and password are case sensitive and must be entered exactly as given by your ISP. Some ISPs use your full e-mail address as the login name. The Service Name is not required by all ISPs. If you use a login name and password, then fill in the following:Login Name: ______________________________ Password: ____________________________Service Name: _____________________________ Fixed or Static IP Address: If you have a static IP address, record the following information. For example, 169.254.141.148 could be a valid IP address.Fixed or Static Internet IP Address: ______.______.______.______Router IP Address: ______.______.______.______Subnet Mask: ______.______.______.______ISP DNS Server Addresses: If you were given DNS server addresses, fill in the following:Primary DNS Server IP Address: ______.______.______.______Secondary DNS Server IP Address: ______.______.______.______Host and Domain Names: Some ISPs use a specific host or domain name like CCA7324-A or home. If you did not get host or domain names, use the following examples as a guide:• If your main e-mail account with your ISP is aaa@yyy.com, then use aaa as your host name. Your ISP might call this your account, user, host, computer, or system name. • If your ISP’s mail server is mail.xxx.yyy.com, then use xxx.yyy.com as the domain name.ISP Host Name: _________________________ ISP Domain Name: _______________________For Wireless Access: For configuration of the wireless network, record the following: Wireless Network Name (SSID): _________________________ WEP Authentication (circle one): Automatic, Open System, or Shared Key WEP Encryption (circle one): 64 or 128; Passphrase or Key: _________________________
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterConnecting the Router to the Internet 3-5August 2004Connecting the DG834GT to Your LANThis section provides instructions for connecting the DG834GT Super Wireless ADSL Router.Note: The Resource CD included with your router contains an animated Installation Assistant to help you through this procedure.How to Connect the RouterThere are four steps to connecting your firewall:1. Install ADSL filters on the phone lines.2. Connect the router to the ADSL filter.3. Log in to the router.4. Connect to the Internet.Follow the steps below to connect your router to your network. Before you begin, locate the ADSL configuration information from your Internet Service Provider (ISP). 1. CONNECT ADSL FILTERS ON THE PHONE LINES.a. You need to install a filter on every telephone or device that shares the same phone number as your ADSL router. Select the filter that came with your router. Figure 3-3: ADSL microfilters Note: If you purchased the DG834GT in a country where the filter is not included, you must acquire one. b. Two-Line Filter Example. Insert the two-line filter into the phone outlet and connect the phone to the phone line connector (A):0HONE0HONE$3,,INEOne-Line FilterTwo-Line FilterSplitterWith Splitter
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router3-6 Connecting the Router to the InternetAugust 2004.Figure 3-4: Connecting an ADSL microfilter and phoneNote: To use a one-line filter with a separate splitter, insert the splitter into the phone outlet, connect the one-line filter to the splitter, and connect the phone to the filter.2. CONNECT THE DG834GT TO THE ADSL FILTER.Note: Improperly connecting a filter to your DG834GT Super Wireless ADSL Router will block your ADSL connection. a. Turn off your computer.b. Connect the ADSL port of the DG834GT to the ADSL port (B) of the two-line filter:0HONE$3,,INEA
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterConnecting the Router to the Internet 3-7August 2004Figure 3-5: Connecting the DG834GT Super Wireless ADSL Router to an ADSL microfilter and phonec. Connect the Ethernet cable (C) from your DG834GT’s LAN port to the Ethernet adapter in your computer.0HONE$3,,INEB
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router3-8 Connecting the Router to the InternetAugust 2004Figure 3-6: Connecting a computer to the DG834GT Super Wireless ADSL RouterNote: The DG834GT Super Wireless ADSL Router incorporates Auto UplinkTM technology. Each Ethernet LAN port will automatically sense whether the cable plugged into the port should have a 'normal' connection (for example, connecting to a computer) or an 'uplink' connection (for example, connecting to a switch or hub). That port will then configure itself to the correct configuration. This feature also eliminates the need to worry about crossover cables, as Auto Uplink will accommodate either type of cable to make the right connection.d. Connect the power adapter to the router and plug it in to a power outlet. Verify the following:The power light is lit after turning on the router.The ADSL link light is solid green, indicating a link has been established to the ADSL network.e. Now, turn on your computer. If software usually logs you in to your Internet connection, do not run that software. Cancel it if it starts automatically. Verify the following:The local lights are lit for any connected computers.Note: For instructions on connecting computers to the DG834GT via wireless links, please see Chapter 4, “Wireless Configuration”.&RPSXWHU0HONE$3,,INE*DWHZD\C
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterConnecting the Router to the Internet 3-9August 20043. LOG IN TO THE DG834GT.Note: Your computer needs to be configured for DHCP. For instructions on configuring for DHCP, please see Appendix C, “Preparing Your Network”.a. Connect to the router by typing http://192.168.0.1 in the address field of Internet Explorer or Netscape® Navigator.Figure 3-7: Connect to the routerA login window opens as shown below:Figure 3-8: Login windowb. When prompted, enter admin for the user name and password for the password, both in lower case letters. After logging in, you will see the menu below.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router3-10 Connecting the Router to the InternetAugust 2004Figure 3-9: Setup Wizard4. CONNECT TO THE INTERNETThe router is now properly attached to your network. You are now ready to configure your router to connect to the Internet. There are two ways you can configure your router to connect to the Internet:a. Let the DG834GT auto-detect the type of Internet connection you have and configure it. See “Auto-Detecting Your Internet Connection Type” on page 3-10 for instructions.b. Manually choose which type of Internet connection you have and configure it. See “Manually Configuring Your Internet Connection” on page 3-15 for instructions.These options are described below. In either case, unless your ISP automatically assigns your configuration automatically via DHCP, you need the configuration parameters from your ISP you recorded in “Record Your Internet Connection Information” on page 3-3.Auto-Detecting Your Internet Connection TypeThe Web Configuration Manager built in to the router contains a Setup Wizard that can automatically determine your network connection type. 1. If your router has not yet been configured, the Setup Wizard shown in Figure 3-9 should launch automatically.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterConnecting the Router to the Internet 3-11August 2004Note: If instead of the Setup Wizard menu, the main menu of the router’s Configuration Manager as shown in Figure 3-15 appears, click the Setup Wizard link in the upper left to bring up this menu.2. You must select a country and language. Language choices are English, French, German, and Italian. After you change the language, the remaining setup screens change to the language of your choice.3. Select Yes to allow the router to automatically determine your connection.4. Click Next.The Setup Wizard will now check for the following connection types:• Dynamic IP assignment• A login protocol such as PPPoE or PPPoA• Classical IP over ATM (RFC1577)• Fixed IP address assignmentNext, the Setup Wizard will report which connection type it has discovered, and then display the appropriate configuration page. If the Setup Wizard finds no connection, you will be prompted to check the physical connection between your router and the ADSL line. When the connection is properly made, the router’s Internet LED should be on.5. The ADSL settings for the multiplexing method and VPI/VCI will update with the preset defaults. The multiplexing method preset default settings will usually work. Only change the multiplexing method if you are sure your ISP requires Virtual Path Identifier (VPI) or Virtual Channel Identifier (VCI) settings that are different from the default values. Incorrect VPI or VCI settings will prevent you from connecting to the Internet. To change these settings, click the ADSL Settings link on the main menu. See “ADSL Settings” on page 3-20 for more details.The procedures for filling in the configuration page for each type of connection follow below.Wizard-Detected PPPoE Login Account SetupIf the Setup Wizard determines that your Internet service account uses a login protocol such as PPP over Ethernet (PPPoE), you will be directed to the PPPoE page shown in Figure 3-10:
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router3-12 Connecting the Router to the InternetAugust 2004Figure 3-10: Setup Wizard menu for PPPoE login accountsEnter the PPPoE login user name and password.Wizard-Detected PPPoA Login Account SetupIf the Setup Wizard determines that your Internet service account uses a login protocol such as PPP over ATM (PPPoA), you will be directed to the PPPoA page shown in Figure 3-11 below:Figure 3-11: Setup Wizard menu for PPPoA login accountsEnter your login user name and password. These fields are case sensitive.Wizard-Detected Dynamic IP Account SetupIf the Setup Wizard determines that your Internet service account uses Dynamic IP assignment, you will be directed to the page shown in Figure 3-12 below:
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterConnecting the Router to the Internet 3-13August 2004Figure 3-12: Setup Wizard menu for Dynamic IP addressClick Apply to set Dynamic IP as the connection method.Wizard-Detected IP Over ATM Account SetupIf the Setup Wizard determines that your Internet service account uses IP over ATM Classical IP assignment (RFC1577), you will be directed to the page shown in Figure 3-13 below:Figure 3-13: Setup Wizard menu for IP over ATM (Classical IP) address1. Enter your assigned IP Address and Subnet Mask. This information should have been provided to you by your ISP. You need the configuration parameters from your ISP you recorded in “Record Your Internet Connection Information” on page 3-3.2. Enter the IP address of your ISP’s Primary DNS Server. If a Secondary DNS Server address is available, enter it also.DNS servers are required to perform the function of translating an Internet name such as www.netgear.com to a numeric IP address. For a fixed IP address configuration, you must obtain DNS server addresses from your ISP and enter them manually here. 3. Click Apply to save the settings.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router3-14 Connecting the Router to the InternetAugust 20044. Click the Test button to test your Internet connection. If the NETGEAR Web site does not appear within one minute, refer to Chapter 8, “Troubleshooting”.Wizard-Detected Fixed IP (Static) Account SetupIf the router determines that your Internet service account uses Fixed IP assignment, you will be directed to the page shown in Figure 3-14 below:Figure 3-14: Setup Wizard menu for Fixed IP address1. If required, enter the Account Name and Domain Name from your ISP.2. Choose “Use Static IP Address” or “Use IP Over ATM” (IPoA — RFC1483 Routed) according to the information from your ISP. If you choose IPoA, the router will be able to detect the gateway IP address but you still need to provide the router IP address.3. Enter your assigned IP Address, Subnet Mask, and the IP Address of your ISP’s gateway router. This information should have been provided to you by your ISP. You need the configuration parameters from your ISP you recorded in “Record Your Internet Connection Information” on page 3-3.4. Enter the IP address of your ISP’s Primary DNS Server. If a Secondary DNS Server address is available, enter it also.DNS servers are required to perform the function of translating an Internet name such as www.netgear.com to a numeric IP address. For a fixed IP address configuration, you must obtain DNS server addresses from your ISP and enter them manually here.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterConnecting the Router to the Internet 3-15August 20045. Click Apply to save the settings.6. Click the Test button to test your Internet connection. If the NETGEAR Web site does not appear within one minute, refer to Chapter 8, “Troubleshooting”.Testing Your Internet ConnectionAfter completing the Internet connection configuration, your can test your Internet connection. Log in to the router, then, from the Basic Settings link in the Setup menu, click the Test button. If the NETGEAR Web site does not appear within one minute, refer to Chapter 8, “Troubleshooting”.Your router is now configured to provide Internet access for your network. Your router automatically connects to the Internet when one of your computers requires access. It is not necessary to run a dialer or login application such as Dial-Up Networking or Enternet to connect, log in, or disconnect. These functions are performed by the router as needed.To access the Internet from any computer connected to your router, launch a browser such as Microsoft Internet Explorer or Netscape Navigator. You should see the router’s Internet LED blink, indicating communication to the ISP. The browser should begin to display a Web page.The following chapters describe how to configure the Advanced features of your router, and how to troubleshoot problems that may occur.Manually Configuring Your Internet Connection You can manually configure your router using the menu below, or you can allow the Setup Wizard to determine your configuration as described in the previous section.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router3-16 Connecting the Router to the InternetAugust 2004Figure 3-15: Basic Settings menuHow to Perform Manual ConfigurationWe recommend that you start the manual configuration from the Setup Wizard:1. Select your country and language. Language choices are English, French, German, and Italian. After you change the language, the remaining setup screens change to the language of your choice.2. Select No to manually configure your router connection.3. Click Next.4. Manually configure the router in the Basic Settings menu shown in Figure 3-15.5. Follow the instructions below according to the encapsulation method and whether your Internet connection requires a login. The following methods are available:• Internet Connection Requires Login and Uses PPPoE• Internet Connection Requires Login and Uses PPPoAISP Does Not Require Login ISP Does Require Login
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterConnecting the Router to the Internet 3-17August 2004• Internet Connection Does Not Require a Login6. Usually the default ADSL Settings work fine for most ISPs and you can skip this step. If you have any problems with your connection, check the ADSL Settings. See “ADSL Settings” on page 3-20 for more details.Internet Connection Requires Login and Uses PPPoE1. If your Internet connection does require login, select Yes and fill in the settings according to the instructions below.Note: You will no longer need to launch the ISP’s login program on your computer in order to access the Internet. When you start an Internet application, your router automatically logs you in.2. Choose PPPoE for the encapsulation method.3. Enter the login name (frequently the email address your ISP provided), password, and service name (if required).4. If you want to change the login timeout, enter a new value in minutes. This determines how long the router keeps the Internet connection active after there is no Internet activity from the LAN. Entering an Idle Timeout value of zero means never log out.5. When a connection uses PPPoE, the IP address is normally assigned automatically. However, the DG834GT allows this address to be set manually.• Select “Get Automatically from ISP” if your ISP assigns your IP address.• Select “Use Static IP Address” if your ISP gave you a statically assigned address. 6. The DNS server is used to look up site addresses based on their names. • Select “Get Automatically from ISP” if your ISP uses DHCP to assign your DNS servers. Your ISP will automatically assign this address. • Select “Use These DNS Servers” if your ISP gave you one or two DNS addresses. Type the primary and secondary addresses.7. You should only disable NAT if you are sure you do not require it. NAT automatically assigns private IP addresses (192.168.0.x) to LAN connected devices. When NAT is disabled, only standard routing is performed by this router. Classical routing lets you directly manage the IP addresses the DG834GT uses. Classical routing should be selected only by experienced users.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router3-18 Connecting the Router to the InternetAugust 2004Note: Disabling NAT will reboot the router and reset all the DG834GT configuration settings to the factory default. Disable NAT only if you plan to install the DG834GT in a setting where you will be manually administering the IP address space on the LAN side of the router.Internet Connection Requires Login and Uses PPPoA1. If your Internet connection does require login, select Yes and fill in the settings according to the instructions below.Note: You will no longer need to launch the ISP’s login program on your computer in order to access the Internet. When you start an Internet application, your router automatically logs you in.2. Choose PPPoA for the encapsulation method.3. Enter the login name (frequently the email address your ISP provided), and password.4. If you want to change the login timeout, enter a new value in minutes. This determines how long the router keeps the Internet connection active after there is no Internet activity from the LAN. Entering an Idle Timeout value of zero means never log out.5. When a connection uses PPPoA, the IP address is normally assigned automatically. However, the DG834GT allows this address to be set manually.• Select “Get Automatically from ISP” if your ISP assigns your IP address.• Select “Use Static IP Address” if your ISP gave you a statically assigned address. 6. The DNS server is used to look up site addresses based on their names. • Select “Get Automatically from ISP” if your ISP uses DHCP to assign your DNS servers. Your ISP will automatically assign this address. 7. Select “Use These DNS Servers” if your ISP gave you one or two DNS addresses. Type the primary and secondary addresses.You should only disable NAT if you are sure you do not require it. NAT automatically assigns private IP addresses (192.168.0.x) to LAN connected devices. When NAT is disabled, only standard routing is performed by this router. Classical routing lets you directly manage the IP addresses the DG834GT uses. Classical routing should be selected only by experienced users.Note: Disabling NAT will reboot the router and reset all the DG834GT configuration settings to the factory default. Disable NAT only if you plan to install the DG834GT in a setting where you will be manually administering the IP address space on the LAN side of the router.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterConnecting the Router to the Internet 3-19August 2004Internet Connection Does Note Require A Login1. If your Internet connection does not require a login, select No and fill in the settings according to the instructions below. 2. Enter your Account Name (may also be called Host Name) and Domain Name. These parameters may be necessary to access your ISP’s mail or news servers.3. Internet IP Address: • Select “Get Dynamically from ISP” if your ISP uses DHCP to assign your IP address. Your ISP will automatically assign these addresses.• Select “Use Static IP Address” if your ISP has assigned you a permanent, fixed (static) IP address. Enter the IP address that your ISP assigned. Also enter the IP Subnet Mask and the Gateway IP Address. The gateway is the ISP’s router to which your router will connect.• Select “IP Over ATM (IPoA)” if your ISP uses Classical IP Addresses (RFC1577). Enter the IP address, IP Subnet Mask, and Gateway IP Addresses that your ISP assigned. 4. Domain Name Server (DNS) Address: • Select “Get Dynamically from ISP” if your ISP uses DHCP to assign your IP address. Your ISP will automatically assign this address.• If you know that your ISP does not automatically transmit DNS addresses to the router during login, select “Use these DNS servers” and enter the IP address of your ISP’s Primary DNS Server. If a Secondary DNS Server address is available, enter it also.A DNS server is a host on the Internet that translates Internet names (such as www.netgear.com) to numeric IP addresses. Typically your ISP transfers the IP address of one or two DNS servers to your router during login. If the ISP does not transfer an address, you must obtain it from the ISP and enter it manually here.5. You should only disable NAT if you are sure you do not require it. NAT automatically assigns private IP addresses (192.168.0.x) to LAN connected devices. When NAT is disabled, only standard routing is performed by this router. Classical routing lets you directly manage the IP addresses the DG834GT uses. Classical routing should be selected only by experienced users.Note: Disabling NAT will reboot the router and reset all the DG834GT configuration settings to the factory default. Disable NAT only if you plan to install the DG834GT in a setting where you will be manually administering the IP address space on the LAN side of the router
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router3-20 Connecting the Router to the InternetAugust 20046. Router MAC Address: This section determines the Ethernet MAC address that will be used by the router on the Internet port. Some ISPs will register the Ethernet MAC address of the network interface card in your computer when your account is first opened. They will then only accept traffic from the MAC address of that computer. This feature allows your router to masquerade as that computer by “cloning” its MAC address. To change the MAC address, select “Use this Computer’s MAC address”. The router will then capture and use the MAC address of the computer that you are now using. You must be using the one computer that is allowed by the ISP. Alternatively, select “Use this MAC address” and enter it.7. Click Apply to save your settings.8. Click the Test button to test your Internet connection. If the NETGEAR Web site does not appear within one minute, refer to Chapter 8, “Troubleshooting”.ADSL SettingsThe default settings of your DG834GT 108 Mbps Super Wireless ADSL Router will work fine for most ISPs. However, some ISPs use a specific Multiplexing Method and Virtual Circuit Number for the Virtual Path Identifier (VPI) and Virtual Channel Identifier (VCI).Note: The correct country must be selected from the Setup Wizard’s first page for the default ADSL Settings to work.If your ISP provided you with a specific Multiplexing Method or VPI/VCI number, then fill in the following:1. Select the ADSL Settings link from the main menu.2. For the Multiplexing Method, select LLC-based or VC-based.3. Type a number between 0 and 255 for the VPI. The default is 8. 4. Type a number between 1 and 65535 for the VCI. The default is 35.5. Click Apply.
Wireless Configuration 4-1August 2004Chapter 4 Wireless ConfigurationThis chapter describes how to configure the wireless features of your DG834GT 108 Mbps Super Wireless ADSL Router.Considerations for a Wireless NetworkIn planning your wireless network, you should consider the level of security required. You should also select the physical placement of your router in order to maximize the network speed. For further information, refer to Appendix D, “Wireless Networking Basics”.To ensure proper compliance and compatibility between similar products in your area, the operating channel and region must be set correctly.Observe Performance, Placement, and Range GuidelinesThe operating distance or range of your wireless connection can vary significantly based on the physical placement of the wireless firewall. The latency, data throughput performance, and notebook power consumption also vary depending on your configuration choices.For best results, place your firewall:• Near the center of the area in which your computers will operate• In an elevated location such as a high shelf where the wirelessly connected computers have line-of-sight access (even if through walls)• Away from sources of interference, such as computers, microwaves, and cordless phones• With the Antenna tight and in the upright position• Away from large metal surfacesNote: Failure to follow these guidelines can result in significant performance degradation or inability to wirelessly connect to the router. For complete range/performance specifications, please see Appendix A, “Technical Specifications”.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router4-2 Wireless ConfigurationAugust 2004The time it takes to establish a wireless connection can vary depending on both your security settings and placement. WEP connections can take slightly longer to establish. Also, WEP encryption can consume more battery power on a notebook computer.Implement Appropriate Wireless Security Unlike wired network data, your wireless data transmissions can extend beyond your walls and can be received by anyone with a compatible adapter. For this reason, use the security features of your wireless equipment. The DG834GT Super Wireless ADSL Router provides highly effective security features which are covered in detail in this chapter. Deploy the security features appropriate to your needs.Figure 4-1: DG834GT wireless data security optionsThere are several ways you can enhance the security of your wireless network:•Restrict Access Based on MAC Address. You can allow only trusted PCs to connect so that unknown PCs cannot wirelessly connect to the DG834GT. Restricting access by MAC address adds an obstacle against unwanted access to your network, but the data broadcast over the wireless link is fully exposed. Note: Indoors, computers can connect over 802.11g wireless networks at a maximum range of up to 300 feet. Such distances can allow for others outside of your immediate area to access your network.1) Open System: Easy but no security2) MAC Access List: No data security3) WEP: Security but some performance impact4) WPA-PSKWireless DataSecurity OptionsRange: Up to 300 FeetPCsServersDG834GT
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterWireless Configuration 4-3August 2004•Turn Off the Broadcast of the Wireless Network Name SSID. If you disable broadcast of the SSID, only devices that have the correct SSID can connect. This nullifies wireless network ‘discovery’ feature of some products, such as Windows XP, but the data is still exposed.•WEP. Wired Equivalent Privacy (WEP) data encryption provides data security. WEP Shared Key authentication and WEP data encryption will block all but the most determined eavesdropper. •WPA-PSK. Wi-Fi Protected Access (WPA) data encryption provides data security. The very strong authentication along with dynamic per frame re-keying of WPA make it virtually impossible to compromise. Because this is a new standard, wireless device driver and software availability may be limited. Understanding Wireless SettingsTo configure the Wireless interface of your router, click the Wireless link in the main menu of the browser interface. The following Wireless Settings menu will appear after WEP (Wired Equivalent Privacy) under Security Options is subsequently selected:
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router4-4 Wireless ConfigurationAugust 2004Figure 4-2: Wireless Settings menuThe following parameters are in the Wireless Settings menu:•Wireless Network.—Name (SSID). The Service Set ID, also known as the wireless network name. Enter a value of up to 32 alphanumeric characters. The same Name (SSID) must be assigned to all wireless devices in your network. The default SSID is NETGEAR, but NETGEAR strongly recommends that you change your network Name to a different value.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterWireless Configuration 4-5August 2004Note: This value is case sensitive. For example, Wireless is not the same as wireless.—Region. Select your region from the drop-down list. This field displays the region of operation for which the wireless interface is intended. It may not be legal to operate the router in a region other than the region shown here.—Channel. This field determines which operating frequency will be used. It should not be necessary to change the wireless channel unless you notice interference problems with another nearby access point.—Mode. • "g & b" allows both "g" and "b" wireless stations to access this device (default).• “g only” allows only 802.11g wireless stations to be used. • “b only” allows 802.11b wireless stations; 802.11g wireless stations can still be used if they can operate in 802.11b mode.• “Auto 108 Mbps” means all 802.11g, 802.11b, and Netgear 108 Mbps wireless stations can be used. The Auto 108 Mbps mode is the second fastest mode.• “108 Mbps only” means only compatible 802.11g wireless stations that support 108 Mbps can connect. The 108 Mbps only mode is the fastest mode.Note: Only use the 108 Mbps only mode when all wireless adapters in your open network bear the 108 Mbps logo.Figure 4-3: 108 Mbps Logo•Wireless Access Point.—Enable Wireless Access Point. This field lets you turn off or turn on the wireless access point built in to the router. The wireless icon on the front of the router will also display the current status of the Wireless Access Point to let you know if it is disabled or enabled. The wireless access point must be enabled to allow wireless stations to access the Internet.—Allow Broadcast of Name (SSID). If enabled, the SSID is broadcast to all Wireless Stations. Stations which have no SSID (or a "null" value) can then adopt the correct SSID for connections to this Access Point.10 8
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router4-6 Wireless ConfigurationAugust 2004—Wireless Isolation. If enabled, Wireless Stations will not be able to communicate with each other or with Stations on the wired network. This feature should normally be disabled.• Wireless Station Access List.— By default, any wireless computer that is configured with the correct wireless network name or SSID will be allowed access to your wireless network. For increased security, you can restrict access to the wireless network to only specific computers based on their MAC addresses. Click Setup Access List to display the Wireless Station Access List menu.• Security OptionsTable 4-1. Wireless Security OptionsField DescriptionDisable Wireless security is not used.WEP (Wired Equivalent Privacy)You can select the following WEP options: Authentication Type• Open: the DG834GT does not perform any authentication. • Shared: WEP shared key authentication. For a full explanation of WEP shared key, see “Authentication and WEP Data Encryption” on page D-2. Encryption Strength• If Shared or Open Network Authentication is enabled, you can choose 64- or 128-bit WEP data encryption. Note: With Open Network Authentication and 64- or 128-bit WEP Data Encryption, the DG834GT does perform 64- or 128-bit data encryption but does not perform any authentication. Security Encryption (WEP) KeyThese key values must be identical on all wireless devices in your network (key 1 must be the same for all, key 2 must be the same for all, and so on). The DG834GT provides two methods for creating WEP encryption keys:• Passphrase. These characters are case sensitive. Enter a word or group of printable characters in the Passphrase box and click the Generate button. Note: Not all wireless adapters support passphrase key generation.• Manual. These values are not case sensitive. 64-bit WEP: enter 10 hexadecimal digits (any combination of 0-9, a-f, or A-F).128-bit WEP: enter 26 hexadecimal digits (any combination of 0-9, a-f, or A-F).
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterWireless Configuration 4-7August 2004How to Set Up and Test Basic Wireless ConnectivityFollow the instructions below to set up and test basic wireless connectivity. Once you have established basic wireless connectivity, you can enable security settings appropriate to your needs.1. Log in to the DG834GT firewall at its default LAN address of http://192.168.0.1 with its default user name of admin and default password of password, or using whatever LAN address and password you have set up.2. Click the Wireless Settings link in the main menu of the DG834GT firewall.3. Choose a suitable descriptive name for the wireless network name (SSID). In the SSID box, enter a value of up to 32 alphanumeric characters. The default SSID is Wireless.Note: The SSID of any wireless access adapters must match the SSID you configure in the DG834GT 108 Mbps Super Wireless ADSL Router. If they do not match, you will not get a wireless connection to the DG834GT.4. Set the Region. Select the region in which the wireless interface will operate. WPA-PSK (Wi-Fi Protected Access Pre-Shared Key)WPA Pre-Shared-Key uses a pre-shared key to perform the authentication and generate the initial data encryption keys. Then, it dynamically varies the encryption key. For a full explanation of WPA, see “WPA Wireless Security” on page D-8.Note: Not all wireless adapters support WPA. Furthermore, client software is required on the client. Windows XP and Windows 2000 with Service Pack 3 do include the client software that supports WPA. Nevertheless, the wireless adapter hardware and driver must also support WPA.WPA-802.1x User authentication is implemented using 802.1x and RADIUS servers. For a full explanation of WPA, see “WPA Wireless Security” on page D-8.Fill in the following:• Radius Server Name/IP Address This field is required. Enter the name or IP address of the Radius Server on your LAN. • Radius Port Enter the port number used for connections to the Radius Server. • Radius Shared Key Enter the desired value for the Radius shared key. This key enables the DG834GT to log in to the Radius server and must match the value used on the Radius server. Table 4-1. Wireless Security OptionsField Description
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router4-8 Wireless ConfigurationAugust 20045. Set the Channel. The default channel is 11.This field determines which operating frequency will be used. It should not be necessary to change the wireless channel unless you notice interference problems with another nearby wireless router or access point. Select a channel that is not being used by any other wireless networks within several hundred feet of your firewall. For more information on the wireless channel frequencies please refer to “Wireless Channels” on page D-7. 6. For initial configuration and test, leave the Wireless Card Access List set to allow everyone access by making sure that “Turn Access Control On” is not selected in the Wireless Station Access List. In addition, leave the Encryption Strength set to “Disabled.” 7. Click Apply to save your changes.8. Configure and test your computers for wireless connectivity.Program the wireless adapter of your computers to have the same SSID and channel that you configured in the router. Check that they have a wireless link and are able to obtain an IP address by DHCP from the firewall.Once your computers have basic wireless connectivity to the firewall, you can configure the advanced wireless security functions of the firewall.How to Restricting Wireless Access to Your NetworkBy default, any wireless PC that is configured with the correct SSID will be allowed access to your wireless network. For increased security, the DG834GT 108 Mbps Super Wireless ADSL Router provides several ways to restrict wireless access to your network:• Turn off wireless connectivity completely• Restrict access based on the Wireless Network Name (SSID)• Restrict access based on the Wireless Card Access ListThese options are discussed below.Note: If you are configuring the firewall from a wireless computer and you change the firewall’s SSID, channel, or security settings, you will lose your wireless connection when you click Apply. You must then change the wireless settings of your computer to match the firewall’s new settings.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterWireless Configuration 4-9August 2004Figure 4-4: Wireless Access Point settingsRestricting Access to Your Network by Turning Off Wireless ConnectivityYou can completely turn off the wireless portion of the DG834GT. For example, if your notebook computer is used to wirelessly connect to your router and you take a business trip, you can turn off the wireless portion of the router while you are traveling. Other members of your household who use computers connected to the router via Ethernet cables will still be able to use the router.Restricting Wireless Access Based on the Wireless Network Name (SSID)The DG834GT can restrict wireless access to your network by not broadcasting the wireless network name (SSID). However, by default, this feature is turned off. If you turn this feature on, wireless devices will not ‘see’ your DG834GT. You must configure your wireless devices to match the wireless network name (SSID) you configure in the DG834GT Super Wireless ADSL Router.Note: The SSID of any wireless access adapters must match the SSID you configure in the DG834GT 108 Mbps Super Wireless ADSL Router. If they do not match, you will not get a wireless connection to the DG834GT.Restricting Wireless Access Based on the Wireless Station Access ListThis list determines which wireless hardware devices will be allowed to connect to the firewall.To restrict access based on MAC addresses, follow these steps:1. Log in to the DG834GT firewall at its default LAN address of http://192.168.0.1 with its default user name of admin and default password of password, or using whatever LAN address and password you have set up.2. From the Wireless Settings menu, Wireless Station Access List section, click the Setup Access List button to display the list, shown below:
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router4-10 Wireless ConfigurationAugust 2004Figure 4-5. Wireless Access menu3. Select the Turn Access Control On check box to enable restricting wireless computers by their MAC addresses.4. If the wireless station is currently connected to the network, you can select it from the Available Wireless Stations list. Click Add to add the station to the Trusted Wireless Stations list.5. If the wireless station is not currently connected, you can enter its address manually. Enter the MAC address of the authorized computer. The MAC address is usually printed on the wireless card, or it may appear in the router’s DHCP table. The MAC address will be 12 hexadecimal digits.Click Add to add your entry. You can add several stations to the list, but the entries will be discarded if you do not click Apply.Note: You can copy and paste the MAC addresses from the router’s Attached Devices menu into the MAC Address box of this menu. To do this, configure each wireless computer to obtain a wireless link to the router. The computer should then appear in the Attached Devices menu.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterWireless Configuration 4-11August 20046. Make sure the Turn Access Control On check box is selected, then click Apply.Now, only devices on this list will be allowed to wirelessly connect to the DG834GT. This prevents unauthorized access to your network. Choosing WEP Authentication and Security Encryption MethodsFigure 4-6. Security Encryption sectionRestricting wireless access prevents intruders from connecting to your network. However, the wireless data transmissions are still vulnerable to snooping. Using the WEP data encryption settings described below will prevent a determined intruder from eavesdropping on your wireless data communications. Also, if you are using the Internet for such activities as purchases or banking, those Internet sites use another level of highly secure encryption called SSL. You can tell if a web site is using SSL because the web address begins with HTTPS rather than HTTP.Authentication Type Selection The DG834GT lets you select the following wireless authentication schemes. Note: If you are configuring the router from a wireless computer whose MAC address is not in the Trusted Wireless Stations list, and you select Trusted Wireless Stations only, you will lose your wireless connection when you click Apply. You must then access the router from a wired computer to make any further changes.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router4-12 Wireless ConfigurationAugust 2004• Automatic• Open System• Shared keySet your wireless adapter according to the authentication scheme you choose for the DG834GT Super Wireless ADSL Router. Please refer to “Authentication and WEP Data Encryption” on page D-2 for a full explanation of each of these options, as defined by the IEEE 802.11g wireless communication standard.Encryption ChoicesPlease refer to “Overview of WEP Parameters” on page D-5 for a full explanation of each of the following choices, as defined by the IEEE 802.11g wireless communication standard. Choose the encryption strength from the drop-down list:DisableNo encryption will be applied. This setting is useful for troubleshooting your wireless connection, but leaves your wireless data fully exposed.64 or 128 bit WEPWhen 64 Bit WEP or 128 Bit WEP is selected, WEP encryption will be applied. If WEP is enabled, you can manually or automatically program the four data encryption keys. These values must be identical on all computers and access points in your network.There are two methods for creating WEP encryption keys:• Passphrase. Enter a word or group of printable characters in the Passphrase box and click the Generate button. • Manual. 64-bit WEP: Enter 10 hexadecimal digits (any combination of 0-9, a-f, or A-F). 128-bit WEP: Enter 26 hexadecimal digits (any combination of 0-9, a-f, or A-F).Select the radio button for the key you want to make active. Note: The authentication scheme is separate from the data encryption. You can choose an authentication scheme which requires a shared key but still leave the data transmissions unencrypted. If you require strong security, use both the Shared Key and WEP encryption settings.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterWireless Configuration 4-13August 2004How to Configure WEPTo configure WEP data encryption, follow these steps:1. Log in to the DG834GT firewall at its default LAN address of http://192.168.0.1 with its default user name of admin and default password of password, or using whatever LAN address and password you have set up.2. Click the Wireless Settings link in the main menu of the DG834GT router. 3. Go to the Security Encryption portion of the page: Figure 4-7. Wireless WEP menu4. Select the Authentication Type.5. Select the Encryption setting.6. Enter the encryption keys. You can manually or automatically program the four data encryption keys. These values must be identical on all computers and Access Points in your network.• Automatic — enter a word or group of printable characters in the Passphrase box and click the Generate button. The four key boxes will be automatically populated with key values.• Manual — enter hexadecimal digits (any combination of 0-9, a-f, or A-F). Select which of the four keys will be active.7. Select the radio button for the key you want to make active.Be sure you clearly understand how the WEP key settings are configured in your wireless adapter. Wireless adapter configuration utilities such as the one included in Windows XP only allow entry of one key which must match the default key you set in the DG834GT.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router4-14 Wireless ConfigurationAugust 20048. Click Apply to save your settings.How to Configure WPA-PSKNote: Not all wireless adapters support WPA. Furthermore, client software is required on the client. Windows XP and Windows 2000 with Service Pack 3 do include the client software that supports WPA. Nevertheless, the wireless adapter hardware and driver must also support WPA. Consult the product document for your wireless adapter and WPA client software for instructions on configuring WPA settings.To configure WPA-PSK, follow these steps:1. Log in at the default LAN address of http://192.168.0.1, with the default user name of admin and default password of password, or using whatever LAN address and password you have set up.2. Click Wireless Settings in the Setup section of the main menu of the DG834GT. 3. Choose the WPA-PSK radio button. The WPA-PSK menu will open.4. Enter the pre-shared key in the Passphrase field. 5. Click Apply to save your settings.Note: When configuring the router from a wireless computer, if you configure WEP settings, you will lose your wireless connection when you click Apply. You must then either configure your wireless adapter to match the router WEP settings or access the router from a wired computer to make any further changes.
Protecting Your Network 5-1August 2004Chapter 5 Protecting Your Network This chapter describes how to use the basic firewall features of the DG834GT 108 Mbps Super Wireless ADSL Router to protect your network.Protecting Access to Your DG834GT 108 Mbps Super Wireless ADSL RouterFor security reasons, the router has its own user name and password. Also, after a period of inactivity for a set length of time, the administrator login will automatically disconnect. When prompted, enter admin for the router User Name and password for the router Password. You can use procedures below to change the router's password and the amount of time for the administrator’s login timeout.Note: The user name and password are not the same as any user name or password your may use to log in to your Internet connection.NETGEAR recommends that you change this password to a more secure password. The ideal password should contain no dictionary words from any language, and should be a mixture of both upper and lower case letters, numbers, and symbols. Your password can be up to 30 characters.How to Change the Built-In Password1. Log in to the router at its default LAN address of http://192.168.0.1 with its default User Name of admin, default password of password, or using whatever Password and LAN address you have chosen for the router.Figure 5-1: Log in to the router2. From the Main Menu of the browser interface, under the Maintenance heading, select Set Password to bring up the menu shown in Figure 5-2.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router5-2 Protecting Your NetworkAugust 2004Figure 5-2: Set Password menu3. To change the password, first enter the old password, and then enter the new password twice.4. Click Apply to save your changes. Note: After changing the password, you will be required to log in again to continue the configuration. If you have backed up the router settings previously, you should do a new backup so that the saved settings file includes the new password. Changing the Administrator Login TimeoutFor security, the administrator's login to the router configuration will timeout after a period of inactivity. To change the login timeout period: 1. In the Set Password menu, type a number in ‘Administrator login times out’ field. The suggested default value is 5 minutes. 2. Click Apply to save your changes or click Cancel to keep the current period. Configuring Basic Firewall ServicesBasic firewall services you can configure include access blocking and scheduling of firewall security. These topics are presented below.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterProtecting Your Network 5-3August 2004Blocking Keywords, Sites, and ServicesThe router provides a variety of options for blocking Internet based content and communications services. With its content filtering feature, the DG834GT Super Wireless ADSL Router prevents objectionable content from reaching your PCs. The router allows you to control access to Internet content by screening for keywords within Web addresses. Key content filtering options include:• Keyword blocking of HTTP traffic.• Outbound Service Blocking limits access from your LAN to Internet locations or services that you specify as off-limits.• Denial of Service (DoS) protection. Automatically detects and thwarts Denial of Service (DoS) attacks such as Ping of Death, SYN Flood, LAND Attack and IP Spoofing.• Blocking unwanted traffic from the Internet to your LAN.The section below explains how to configure your router to perform these functions.How to Block Keywords and SitesThe DG834GT Super Wireless ADSL Router allows you to restrict access to Internet content based on functions such as Web addresses and Web address keywords. 1. Log in to the router at its default LAN address of http://192.168.0.1 with its default User Name of admin, default password of password, or using whatever Password and LAN address you have chosen for the router.2. Select the Block Sites link of the Security menu.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router5-4 Protecting Your NetworkAugust 2004 Figure 5-3: Block Sites menu3. To enable keyword blocking, select one of the following:• Per Schedule—to turn on keyword blocking according to the settings on the Schedule page.• Always—to turn on keyword blocking all of the time, independent of the Schedule page.4. Enter a keyword or domain in the Keyword box, click Add Keyword, then click Apply. Some examples of Keyword application follow:• If the keyword “XXX” is specified, the URL <http://www.badstuff.com/xxx.html> is blocked.• If the keyword “.com” is specified, only Web sites with other domain suffixes (such as .edu or.gov) can be viewed.• Enter the keyword “.” to block all Internet browsing access.Up to 32 entries are supported in the Keyword list.5. To delete a keyword or domain, select it from the list, click Delete Keyword, then click Apply.6. To specify a trusted user, enter that computer’s IP address in the Trusted IP Address box and click Apply.You can specify one trusted user, which is a computer that will be exempt from blocking and logging. Since the trusted user will be identified by an IP address, you should configure that computer with a fixed IP address.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterProtecting Your Network 5-5August 20047. Click Apply to save your settings.Firewall RulesFirewall rules are used to block or allow specific traffic passing through from one side of the router to the other. Inbound rules (WAN to LAN) restrict access by outsiders to private resources, selectively allowing only specific outside users to access specific resources. Outbound rules (LAN to WAN) determine what outside resources local users can have access to.A firewall has two default rules, one for inbound traffic and one for outbound. The default rules of the DG834GT are:• Inbound: Block all access from outside except responses to requests from the LAN side.• Outbound: Allow all access from the LAN side to the outside.You can define additional rules that will specify exceptions to the default rules. By adding custom rules, you can block or allow access based on the service or application, source or destination IP addresses, and time of day. You can also choose to log traffic that matches or does not match the rule you have defined.You can change the order of precedence of rules so that the rule that applies most often will take effect first. See “Order of Precedence for Rules” on page 5-11 for more details.To access the rules configuration of the DG834GT, click the Firewall Rules link on the main menu, then click Add for either an Outbound or Inbound Service.Figure 5-4: Rules menu
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router5-6 Protecting Your NetworkAugust 2004• To edit an existing rule, select its button on the left side of the table and click Edit.• To delete an existing rule, select its button on the left side of the table and click Delete.• To move an existing rule to a different position in the table, select its button on the left side of the table and click Move. At the script prompt, enter the number of the desired new position and click OK.Inbound Rules (Port Forwarding)Because the DG834GT uses Network Address Translation (NAT), your network presents only one IP address to the Internet, and outside users cannot directly address any of your local computers. However, by defining an inbound rule you can make a local server (for example, a Web server or game server) visible and available to the Internet. The rule tells the router to direct inbound traffic for a particular service to one local server based on the destination port number. This is also known as port forwarding.Remember that allowing inbound services opens holes in your firewall. Only enable those ports that are necessary for your network. Following are two application examples of inbound rules:Inbound Rule Example: A Local Public Web ServerIf you host a public Web server on your local network, you can define a rule to allow inbound Web (HTTP) requests from any outside IP address to the IP address of your Web server at any time of day. This rule is shown in Figure 5-5:Note: Some residential broadband ISP accounts do not allow you to run any server processes (such as a Web or FTP server) from your location. Your ISP may periodically check for servers and may suspend your account if it discovers any active services at your location. If you are unsure, refer to the Acceptable Use Policy of your ISP.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterProtecting Your Network 5-7August 2004Figure 5-5: Rule example: A Local Public Web ServerThe parameters are:•Service From this list, select the application or service to be allowed or blocked. The list already displays many common services, but you are not limited to these choices. Use the Services menu to add any additional services or applications that do not already appear.• Action Choose how you want this type of traffic to be handled. You can block or allow always, or you can choose to block or allow according to the schedule you have defined in the Schedule menu.• Send to LAN Server Enter the IP address of the computer or server on your LAN which will receive the inbound traffic covered by this rule.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router5-8 Protecting Your NetworkAugust 2004• WAN Users These settings determine which packets are covered by the rule, based on their source (WAN) IP address. Select the desired option: • Any — all IP addresses are covered by this rule. • Address range — if this option is selected, you must enter the Start and Finish fields. • Single address — enter the required address in the Start field. •Log You can select whether the traffic will be logged. The choices are:• Never — no log entries will be made for this service.• Always — any traffic for this service type will be logged.• Match — traffic of this type which matches the parameters and action will be logged.• Not match — traffic of this type which does not match the parameters and action will be logged.Inbound Rule Example: Allowing VideoconferencingIf you want to allow incoming videoconferencing to be initiated from a restricted range of outside IP addresses, such as from a branch office, you can create an inbound rule. In the example shown in Figure 5-6, CU-SeeMe connections are allowed only from a specified range of external IP addresses. In this case, we have also specified logging of any incoming CU-SeeMe requests that do not match the allowed parameters.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterProtecting Your Network 5-9August 2004Figure 5-6: Rule example: Videoconference from Restricted AddressesConsiderations for Inbound Rules• If your external IP address is assigned dynamically by your ISP, the IP address may change periodically as the DHCP lease expires. Consider using the Dynamic DNS feature in the Advanced menu so that external users can always find your network.• If the IP address of the local server computer is assigned by DHCP, it may change when the computer is rebooted. To avoid this, use the Reserved IP address feature in the LAN IP menu to keep the computer’s IP address constant.• Local computers must access the local server using the computer’s local LAN address (192.168.0.11 in the example in Figure 5-6 above). Attempts by local computers to access the server using the external WAN IP address will fail.Outbound Rules (Service Blocking)The DG834GT allows you to block the use of certain Internet services by computers on your network. This is called service blocking or port filtering. You can define an outbound rule to block Internet access from a local computer based on:• IP address of the local computer (source address)• IP address of the Internet site being contacted (destination address)•Time of day• Type of service being requested (service port number)
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router5-10 Protecting Your NetworkAugust 2004Following is an application example of outbound rules:Outbound Rule Example: Blocking Instant MessengerIf you want to block Instant Messenger usage by employees during working hours, you can create an outbound rule to block that application from any internal IP address to any external address according to the schedule that you have created in the Schedule menu. You can also have the router log any attempt to use Instant Messenger during that blocked period.Figure 5-7: Rule example: Blocking Instant MessengerThe parameters are:•Service From this list, select the application or service to be allowed or blocked. The list already displays many common services, but you are not limited to these choices. Use the Add Custom Service feature to add any additional services or applications that do not already appear.• Action Choose how you want this type of traffic to be handled. You can block or allow always, or you can choose to block or allow according to the schedule you have defined in the Schedule menu.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterProtecting Your Network 5-11August 2004• LAN Users These settings determine which packets are covered by the rule, based on their source LAN IP address. Select the desired option: • Any — all IP addresses are covered by this rule. • Address range — if this option is selected, you must enter the Start and Finish fields. • Single address — enter the required address in the Start field. • WAN Users These settings determine which packets are covered by the rule, based on their destination WAN IP address. Select the desired option: • Any — all IP addresses are covered by this rule. • Address range —if this option is selected, you must enter the Start and Finish fields. • Single address — enter the required address in the Start field. •Log You can select whether the traffic will be logged. The choices are:• Never — no log entries will be made for this service.• Always — any traffic for this service type will be logged.• Match — traffic of this type that matches the parameters and action will be logged.• Not match — traffic of this type that does not match the parameters and action will be logged.Order of Precedence for RulesAs you define new rules, they are added to the tables in the Rules menu, as shown in Figure 5-8:
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router5-12 Protecting Your NetworkAugust 2004Figure 5-8: Rules table with examplesFor any traffic attempting to pass through the firewall, the packet information is subjected to the rules in the order shown in the Rules Table, beginning at the top and proceeding to the default rules at the bottom. In some cases, the order of precedence of two or more rules may be important in determining the disposition of a packet. The Move button allows you to relocate a defined rule to a new position in the table.ServicesServices are functions performed by server computers at the request of client computers. For example, Web servers serve Web pages, time servers serve time and date information, and game hosts serve data about other players’ moves. When a computer on the Internet sends a request for service to a server computer, the requested service is identified by a service or port number. This number appears as the destination port number in the transmitted IP packets. For example, a packet that is sent with destination port number 80 is an HTTP (Web server) request.The service numbers for many common protocols are defined by the Internet Engineering Task Force (IETF) and published in RFC1700, “Assigned Numbers.” Service numbers for other applications are typically chosen from the range 1024 to 65535 by the authors of the application.Although the DG834GT already holds a list of many service port numbers, you are not limited to these choices. Use the procedure below to create your own service definitions.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterProtecting Your Network 5-13August 2004How to Define Services1. Log in to the router at its default LAN address of http://192.168.0.1 with its default User Name of admin, default password of password, or using whatever Password and LAN address you have chosen for the router.2. Select the Services link of the Security menu to display the Services menu shown in Figure 5-9:Figure 5-9: Services menu• To create a new Service, click the Add Custom Service button.• To edit an existing Service, select its button on the left side of the table and click Edit Service.• To delete an existing Service, select its button on the left side of the table and click Delete Service.3. Use the page shown below to define or edit a service. Figure 5-10: Add Services menu4. Click Apply to save your changes.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router5-14 Protecting Your NetworkAugust 2004Setting Times and Scheduling Firewall ServicesThe DG834GT Super Wireless ADSL Router uses the Network Time Protocol (NTP) to obtain the current time and date from one of several Network Time Servers on the Internet.How to Set Your Time ZoneIn order to localize the time for your log entries, you must specify your Time Zone:1. Log in to the router at its default LAN address of http://192.168.0.1 with its default User Name of admin, default password of password, or using whatever Password and LAN address you have chosen for the router.2. Select the Schedule link of the Security menu to display menu shown below. Figure 5-11: Schedule Services menu3. Select your Time Zone. This setting will be used for the blocking schedule according to your local time zone and for time-stamping log entries.Select the Adjust for daylight savings time check box if your time zone is currently in daylight savings time.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterProtecting Your Network 5-15August 2004Note: If your region uses Daylight Savings Time, you must manually select Adjust for Daylight Savings Time on the first day of Daylight Savings Time, and clear it at the end. Enabling Daylight Savings Time will cause one hour to be added to the standard time.4. The router has a list of NETGEAR NTP servers. If you would prefer to use a particular NTP server as the primary server, enter its IP address under Use this NTP Server.5. Click Apply to save your settings.How to Schedule Firewall ServicesIf you enabled services blocking in the Block Services menu or Port forwarding in the Ports menu, you can set up a schedule for when blocking occurs or when access is not restricted. 1. Log in to the router at its default LAN address of http://192.168.0.1 with its default User Name of admin, default password of password, or using whatever Password and LAN address you have chosen for the router.2. Select the Schedule link of the Security menu to display menu shown above in the Schedule Services menu.3. To block Internet services based on a schedule, select Every Day or select one or more days. If you want to limit access completely for the selected days, select All Day. Otherwise, to limit access during certain times for the selected days, enter Start Blocking and End Blocking times.Note: Enter the values in 24-hour time format. For example, 10:30 am would be 10 hours and 30 minutes and 10:30 pm would be 22 hours and 30 minutes. If you set the start time after the end time, the schedule will be effective through midnight the next day.4. Click Apply to save your changes.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router5-16 Protecting Your NetworkAugust 2004
Managing Your Network 6-1August 2004Chapter 6 Managing Your Network This chapter describes how to perform network management tasks with your DG834GT 108 Mbps Super Wireless ADSL Router. Backing Up, Restoring, or Erasing Your SettingsThe configuration settings of the DG834GT Super Wireless ADSL Router are stored in a configuration file in the router. This file can be backed up to your computer, restored, or reverted to factory default settings. The procedures below explain how to do these tasks.How to Back Up the Configuration to a File1. Log in to the router at its default LAN address of http://192.168.0.1 with its default User Name of admin, default password of password, or using whatever User Name, Password and LAN address you have chosen for the router.2. From the Maintenance heading of the Main Menu, select the Backup Settings menu as seen in Figure 6-1. Figure 6-1: Backup Settings menu3. Click Backup to save a copy of the current settings.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router6-2 Managing Your NetworkAugust 20044. Store the.cfg file on a computer on your network.How to Restore the Configuration from a File1. Log in to the router at its default LAN address of http://192.168.0.1 with its default User Name of admin, default password of password, or using whatever User Name, Password and LAN address you have chosen for the router.2. From the Maintenance heading of the Main Menu, select the Settings Backup menu as seen in Figure 6-1.3. Enter the full path to the file on your network or click the Browse button to locate the file. 4. When you have located the.cfg file, click the Restore button to upload the file to the router.5. The router will then reboot automatically.How to Erase the ConfigurationIt is sometimes desirable to restore the router to the factory default settings. This can be done by using the Erase function. 1. To erase the configuration, from the Maintenance menu Settings Backup link, click the Erase button on the screen.2. The router will then reboot automatically.After an erase, the router's password will be password, the LAN IP address will be 192.168.0.1, and the router's DHCP client will be enabled.Note: To restore the factory default configuration settings without knowing the login password or IP address, you must use the Default Reset button on the rear panel of the router. See “DG834GT Rear Panel“ on page 2-9.Upgrading the Router’s FirmwareThe software of the DG834GT Super Wireless ADSL Router is stored in FLASH memory, and can be upgraded as new software is released by NETGEAR. Upgrade files can be downloaded from NETGEAR's Web site. If the upgrade file is compressed (.ZIP file), you must first extract the binary (.BIN or.IMG) file before uploading it to the router.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterManaging Your Network 6-3August 2004How to Upgrade the Router FirmwareNote: NETGEAR recommends that you back up your configuration before doing a firmware upgrade. After the upgrade is complete, you may need to restore your configuration settings. 1. Download and unzip the new software file from NETGEAR. The Web browser used to upload new firmware into the router must support HTTP uploads. NETGEAR recommends using Microsoft Internet Explorer 5.0 or above, or Netscape Navigator 4.7 or above. 2. Log in to the router at its default LAN address of http://192.168.0.1 with its default User Name of admin, default password of password, or using whatever User Name, Password and LAN address you have chosen for the router.3. From the Main Menu of the browser interface, under the Maintenance heading, select the Router Upgrade heading to display the menu shown in Figure 6-2. Figure 6-2: Router Upgrade menu4. In the Router Upgrade menu, click the Browse to locate the binary (.BIN or.IMG) upgrade file.5. Click Upload.Note: When uploading software to the router, it is important not to interrupt the Web browser by closing the window, clicking a link, or loading a new page. If the browser is interrupted, it may corrupt the software. When the upload is complete, your router will automatically restart. The upgrade process will typically take about one minute. In some cases, you may need to clear the configuration and reconfigure the router after upgrading.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router6-4 Managing Your NetworkAugust 2004Network Management InformationThe DG834GT provides a variety of status and usage information which is discussed below. Viewing Router Status and Usage StatisticsFrom the Main Menu, under Maintenance, select Router Status to view the screen in Figure 6-3.Figure 6-3: Router Status screenThe Router Status menu provides status and usage information. This screen shows the following parameters:
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterManaging Your Network 6-5August 2004Click the Show Statistics button to display router usage statistics, as shown in Figure 6-3 below:Table 6-1. Menu 3.2 - Router Status FieldsField DescriptionAccount Name The Host Name assigned to the router in the Basic Settings menu.Firmware Version This field displays the router firmware version.ADSL Port These parameters apply to the Internet (ADSL) port of the router. MAC Address This field displays the Ethernet MAC address being used by the Internet (ADSL) port of the router.IP Address This field displays the IP address being used by the Internet (ADSL) port of the router. If no address is shown, the router cannot connect to the Internet.DHCP If None, the router will use a fixed IP address on the ADSL.If Client, the router will obtain an IP address dynamically from the ISP.IP Subnet Mask This field displays the IP Subnet Mask being used by the Internet (ADSL) port of the router.Domain Name Server (DNS) This field displays the DNS Server IP addresses being used by the router. These addresses are usually obtained dynamically from the ISP.LAN Port These parameters apply to the Local (ADSL) port of the router. MAC Address This field displays the Ethernet MAC address being used by the Local (LAN) port of the router.IP Address This field displays the IP address being used by the Local (LAN) port of the router. The default is 192.168.0.1.DHCP If OFF, the router will not assign IP addresses to PCs on the LAN.If ON, the router will assign IP addresses to PCs on the LAN.IP Subnet Mask This field displays the IP Subnet Mask being used by the Local (LAN) port of the router. The default is 255.255.255.0.Modem These parameters apply to the Local (WAN) port of the router. ADSL Firmware Version The version of the firmware.Modem Status The connection status of the modem.Downstream Speed The speed at which the modem is receiving data from the ADSL line.Upstream Speed The speed at which the modem is transmitting data to the ADSL line.VPI The Virtual Path Identifier setting.VCI The Virtual Channel Identifier setting.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router6-6 Managing Your NetworkAugust 2004Figure 6-4: Router Statistics screenThis screen shows the following statistics:.Click the Connection Status button to display router connection status, as shown in Figure 6-5 and Figure 6-6.Table 6-1. Router Statistics FieldsField DescriptionWAN, LAN, or Serial Port The statistics for the WAN (Internet), LAN (local), and Serial ports. For each port, the screen displays:Status The link status of the port.TxPkts The number of packets transmitted on this port since reset or manual clear.RxPkts The number of packets received on this port since reset or manual clear.Collisions The number of collisions on this port since reset or manual clear.Tx B/s The current line utilization—percentage of current bandwidth used on this port.Rx B/s The average line utilization for this port.Up Time The time elapsed since the last power cycle or reset.Poll Interval Specifies the interval at which the statistics are updated in this window. Click Stop to freeze the display.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterManaging Your Network 6-7August 2004Figure 6-5: Connection Status screen for Dynamic IPClicking the Renew button updates the status information.This screen shows the following statistics:Table 6-1. Connection Status Fields for Dynamic IPField DescriptionIP Address The IP Address assigned to the WAN port by the ADSL Internet Service Provider.Subnet Mask The Network Mask assigned to the WAN port by the ADSL Internet Service Provider.Default Gateway The default gateway router assigned to the WAN port by the ADSL Internet Service Provider. DHCP Server The DHCP server’s IP address.DNS Server The DNS server’s IP address.Lease Obtained Date and time the lease was obtained.Lease Expires Date and time the lease expires.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router6-8 Managing Your NetworkAugust 2004An alternate view of the Connection Status screen is shown in Figure 6-6 below:Figure 6-6: Connection Status screen for PPPoAClicking the Renew button updates the status information.This screen shows the following statistics:Table 6-1. Connection Status Fields for PPPoAField DescriptionConnection Time The time elapsed since the last connection to the Internet via the ADSL port.Connecting to Sender The connection status.Negotiation ON or OFFAuthentication ON or OFFIP Address The IP Address assigned to the WAN port by the ADSL Internet Service Provider.Network Mask The Network Mask assigned to the WAN port by the ADSL Internet Service Provider.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterManaging Your Network 6-9August 2004Viewing Attached DevicesThe Attached Devices menu contains a table of all IP devices that the router has discovered on the local network. From the Main Menu of the browser interface, under the Maintenance heading, select Attached Devices to view the table, shown in Figure 6-7:Figure 6-7: Attached Devices menuFor each device, the table shows the IP address, Device Name if available, and the Ethernet MAC address. Note that if the router is rebooted, the table data is lost until the router rediscovers the devices. To force the router to look for attached devices, click the Refresh button.Viewing, Selecting, and Saving Logged InformationThe router will log security-related events such as denied incoming service requests, hacker probes, and administrator logins. If you enabled content filtering in the Block Sites menu, the Logs page can show you when someone on your network tries to access a blocked site. If you enabled e-mail notification, you will receive these logs in an e-mail message. If you do not have e-mail notification enabled, you can view the logs here. An example of the logs file is shown below.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router6-10 Managing Your NetworkAugust 2004Figure 6-8: Security Logs menuLog entries are described in Table 6-1 below:
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterManaging Your Network 6-11August 2004Log action buttons are described in Table 6-2 below:Selecting What Information to LogBesides the standard information listed above, you can choose to log additional information. Those optional selections are as follows:• Attempted access to blocked site• Connections to the Web-based interface of the router• Router operation (start up, get time, etc.)• Known DoS attacks and Port ScansTable 6-1. Security Log entry descriptionsField DescriptionDate and Time The date and time the log entry was recorded.Description or Action The type of event and what action was taken if any.Source IP The IP address of the initiating device for this log entry.Source port and interface The service port number of the initiating device, and whether it originated from the LAN or WANDestination The name or IP address of the destination device or Web site.Destination port and interface The service port number of the destination device, and whether it’s on the LAN or WAN.Table 6-2. Security Log action buttonsField DescriptionRefresh Refresh the log screen.Clear Log Clear the log entries.Send Log Email the log immediately.Apply Apply the current settings.Cancel Clear the current settings.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router6-12 Managing Your NetworkAugust 2004Saving Log Files on a ServerYou can choose to write the logs to a computer running a syslog program. To activate this feature, select to Broadcast on Lan or enter the IP address of the server where the Syslog file will be written.Examples of Log MessagesFollowing are examples of log messages. In all cases, the log entry shows the timestamp as: Day, Year-Month-Date Hour:Minute:SecondActivation and AdministrationTue, 2002-05-21 18:48:39 - NETGEAR activated [This entry indicates a power-up or reboot with initial time entry.]Tue, 2002-05-21 18:55:00 - Administrator login successful - IP:192.168.0.2 Thu, 2002-05-21 18:56:58 - Administrator logout - IP:192.168.0.2 [This entry shows an administrator logging in and out from IP address 192.168.0.2.]Tue, 2002-05-21 19:00:06 - Login screen timed out - IP:192.168.0.2[This entry shows a time-out of the administrator login.]Wed, 2002-05-22 22:00:19 - Log emailed[This entry shows when the log was emailed.]Dropped Packets Wed, 2002-05-22 07:15:15 - TCP packet dropped - Source:64.12.47.28,4787,WAN - Destination:134.177.0.11,21,LAN - [Inbound Default rule match]Sun, 2002-05-22 12:50:33 - UDP packet dropped - Source:64.12.47.28,10714,WAN - Destination:134.177.0.11,6970,LAN - [Inbound Default rule match]Sun, 2002-05-22 21:02:53 - ICMP packet dropped - Source:64.12.47.28,0,WAN - Destination:134.177.0.11,0,LAN - [Inbound Default rule match][These entries show an inbound FTP (port 21) packet, User Datagram Protocol (UDP) packet (port 6970), and Internet Control Message Protocol (ICMP) packet (port 0) being dropped as a result of the default inbound rule, which states that all inbound packets are denied.]
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterManaging Your Network 6-13August 2004Enabling Security Event E-mail NotificationIn order to receive logs and alerts by e-mail, you must provide your e-mail information in the E-mail subheading:Figure 6-9: E-mail menu•Turn e-mail notification on. Select this check box if you want to receive e-mail logs and alerts from the router.•Send alerts and logs via email. Enter the name or IP address of your ISP’s outgoing (SMTP) mail server (such as mail.myISP.com). You may be able to find this information in the configuration menu of your e-mail program. Enter the e-mail address to which logs and alerts are sent. This e-mail address will also be used as the From address. If you leave this box blank, log and alert messages will not be sent via e-mail. •Send alert immediately. Select the corresponding check box if you would like immediate notification of a significant security event, such as a known attack, port scan, or attempted access to a blocked site.•Send logs according to this schedule. Specifies how often to send the logs: Hourly, Daily, Weekly, or When Full. – Day for sending log Specifies which day of the week to send the log. Relevant when the log is sent weekly or daily.– Time for sending log Specifies the time of day to send the log. Relevant when the log is sent daily or weekly.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router6-14 Managing Your NetworkAugust 2004If the Weekly, Daily or Hourly option is selected and the log fills up before the specified period, the log is automatically e-mailed to the specified e-mail address. After the log is sent, it is cleared from the router’s memory. If the router cannot e-mail the log file, the log buffer may fill up. In this case, the router overwrites the log and discards its contents.Running Diagnostic Utilities and Rebooting the RouterThe DG834GT Super Wireless ADSL Router has a diagnostics feature. You can use the diagnostics menu to perform the following functions from the router:• Ping an IP Address to test connectivity to see if you can reach a remote host.• Perform a DNS Lookup to test if an Internet name resolves to an IP address to verify that the DNS server configuration is working.• Display the Routing Table to identify what other routers the router is communicating with.• Reboot the router to enable new network configurations to take effect or to clear problems with the router’s network connection.From the Main Menu of the browser interface, under the Maintenance heading, select the Router Diagnostics heading to display the menu shown in Figure 6-10. Figure 6-10: Diagnostics menu
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterManaging Your Network 6-15August 2004Enabling Remote ManagementUsing the Remote Management page, you can allow a user or users on the Internet to configure, upgrade and check the status of your DG834GT 108 Mbps Super Wireless ADSL Router.Configuring Remote Management1. Log in to the router at its default LAN address of http://192.168.0.1 with its default User Name of admin, default password of password, or using whatever User Name, Password and LAN address you have chosen for the router.2. From the Advanced section of the main menu, select the Remote Management link.3. Select the Turn Remote Management On check box.4. Specify what external addresses will be allowed to access the router’s remote management. For security, restrict access to as few external IP addresses as practical:• To allow access from any IP address on the Internet, select Everyone. • To allow access from a range of IP addresses on the Internet, select IP address range. Enter a beginning and ending IP address to define the allowed range. • To allow access from a single IP address on the Internet, select Only this Computer. Enter the IP address that will be allowed access. 5. Specify the Port Number that will be used for accessing the management interface.Web browser access normally uses the standard HTTP service port 80. For greater security, you can change the remote management Web interface to a custom port by entering that number in the box provided. Choose a number between 1024 and 65535, but do not use the number of any common service port. The default is 8080, which is a common alternate for HTTP.6. Click Apply to have your changes take effect.Note: Be sure to change the router's default password to a very secure password. The ideal password should contain no dictionary words from any language, and should be a mixture of letters (both upper and lower case), numbers, and symbols. Your password can be up to 30 characters.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router6-16 Managing Your NetworkAugust 2004When accessing your router from the Internet, you will type your router's WAN IP address in your browser's Address (in IE) or Location (in Netscape) box, followed by a colon (:) and the custom port number. For example, if your external address is 134.177.0.123 and you use port number 8080, enter in your browser:http://134.177.0.123:8080Note: In this case, the http:// must be included in the address.
Advanced Configuration 7-1August 2004Chapter 7 Advanced Configuration This chapter describes how to configure the advanced features of your DG834GT 108 Mbps Super Wireless ADSL Router. Configuring Advanced SecurityThe DG834GT 108 Mbps Super Wireless ADSL Router provides a variety of advanced features, such as:• Setting up a Demilitarized Zone (DMZ) Server• Connecting Automatically, as Required• Disabling Port Scan and DOS Protection• Responding to a Ping on the Internet WAN Port•MTU Size • Flexibility on configuring your LAN TCP/IP settings• Using the Router as a DHCP Server• Configuring Dynamic DNS• Configuring Static RoutesThese features are discussed below.Setting Up A Default DMZ ServerThe Default DMZ Server feature is helpful when using some online games and videoconferencing applications that are incompatible with NAT. The router is programmed to recognize some of these applications and to work properly with them, but there are other applications that may not function well. In some cases, one local computer can run the application properly if that computer’s IP address is entered as the Default DMZ Server.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router7-2 Advanced ConfigurationAugust 2004Incoming traffic from the Internet is normally discarded by the router unless the traffic is a response to one of your local computers or a service that you have configured in the Ports menu. Instead of discarding this traffic, you can have it forwarded to one computer on your network. This computer is called the Default DMZ Server.How to Configure a Default DMZ ServerTo assign a computer or server to be a Default DMZ server, follow these steps: 1. Log in to the router at its default LAN address of http://192.168.0.1 with its default User Name of admin, default password of password, or using whatever Password and LAN address you have chosen for the router.2. From the Main Menu, under Advanced, click the WAN Setup link to view the page shown in Figure 7-1:Figure 7-1: WAN Setup Page3. Select the Default DMZ Server check box.4. Type the IP address for that server. 5. Click Apply to save your changes. Note: For security reasons, you should avoid using the Default DMZ Server feature. When a computer is designated as the Default DMZ Server, it loses much of the protection of the firewall, and is exposed to many exploits from the Internet. If compromised, the computer can be used to attack your network.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterAdvanced Configuration 7-3August 2004Connect Automatically, as Required Normally, this option should be enabled, so that an Internet connection will be made automatically, whenever Internet-bound traffic is detected. If this causes high connection costs, you can disable this setting. If disabled, you must connect manually, using the sub-screen accessed from the "Connection Status" button on the Status screen.If you have an "Always on" connection, this setting has no effect.Disable Port Scan and DOS ProtectionThe Firewall protects your LAN against Port Scans and Denial of Service (DOS) attacks. This should be disabled only in special circumstances.Respond to Ping on Internet WAN Port If you want the router to respond to a 'ping' from the Internet, select the ‘Respond to Ping on Internet WAN Port’ check box. This should only be used as a diagnostic tool, since it allows your router to be discovered. Do not select this box unless you have a specific reason to do so.MTU Size The normal MTU (Maximum Transmit Unit) value for most Ethernet networks is 1500 Bytes, or 1492 Bytes for PPPoE connections. For some ISPs you may need to reduce the MTU. But this is rarely required, and should not be done unless you are sure it is necessary for your ISP connection.Configuring LAN IP SettingsThe LAN IP Setup menu allows configuration of LAN IP services such as DHCP and RIP. These features can be found under the Advanced heading in the Main Menu of the browser interface.The router is shipped preconfigured to use private IP addresses on the LAN side, and to act as a DHCP server. The router’s default LAN IP configuration is:• LAN IP addresses—192.168.0.1• Subnet mask—255.255.255.0
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router7-4 Advanced ConfigurationAugust 2004These addresses are part of the Internet Engineering Task Force (IETF)-designated private address range for use in private networks, and should be suitable in most applications. If your network has a requirement to use a different IP addressing scheme, you can make those changes in this menu.Figure 7-2: LAN IP Setup MenuThe LAN TCP/IP Setup parameters are:• IP Address This is the LAN IP address of the router.• IP Subnet Mask This is the LAN Subnet Mask of the router. Combined with the IP address, the IP Subnet Mask allows a device to know which other addresses are local to it, and which must be reached through a gateway or router.• RIP Direction RIP (Router Information Protocol) allows a router to exchange routing information with other routers. The RIP Direction selection controls how the Router sends and receives RIP packets. Both is the default. — When set to Both or Out Only, the router will broadcast its routing table periodically. — When set to Both or In Only, it will incorporate the RIP information that it receives. — When set to None, it will not send any RIP packets and will ignore any RIP packets received.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterAdvanced Configuration 7-5August 2004• RIP Version This controls the format and the broadcasting method of the RIP packets that the router sends. It recognizes both formats when receiving. By default, this is set for RIP-1. — RIP-1 is universally supported. RIP-1 is probably adequate for most networks, unless you have an unusual network setup. — RIP-2 carries more information. Both RIP-2B and RIP-2M send the routing data in RIP-2 format. — RIP-2B uses subnet broadcasting. — RIP-2M uses multicasting.DHCPBy default, the router will function as a DHCP (Dynamic Host Configuration Protocol) server, allowing it to assign IP, DNS server, and default gateway addresses to all computers connected to the router's LAN. The assigned default gateway address is the LAN address of the router. IP addresses will be assigned to the attached PCs from a pool of addresses specified in this menu. Each pool address is tested before it is assigned to avoid duplicate addresses on the LAN.For most applications, the default DHCP and TCP/IP settings of the router are satisfactory. See “IP Configuration by DHCP”on page B-9 for an explanation of DHCP and information about how to assign IP addresses for your network. Use Router as DHCP serverIf another device on your network will be the DHCP server, or if you will manually configure the network settings of all of your computers, clear the ‘Use router as DHCP server’ check box. Otherwise, leave it selected. Specify the pool of IP addresses to be assigned by setting the Starting IP Address and Ending IP Address. These addresses should be part of the same IP address subnet as the router’s LAN IP address. Using the default addressing scheme, you should define a range between 192.168.0.2 and 192.168.0.254, although you may want to save part of the range for devices with fixed addresses.The router will deliver the following parameters to any LAN device that requests DHCP:Note: If you change the LAN IP address of the router while connected through the browser, you will be disconnected. You must then open a new connection to the new IP address and log in again.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router7-6 Advanced ConfigurationAugust 2004• An IP Address from the range you have defined• Subnet Mask• Gateway IP Address is the router’s LAN IP address• Primary DNS Server, if you entered a Primary DNS address in the Basic Settings menu; otherwise, the router’s LAN IP address• Secondary DNS Server, if you entered a Secondary DNS address in the Basic Settings menu• WINS Server, short for Windows Internet Naming Service Server, determines the IP address associated with a particular Windows computer. A WINS server records and reports a list of names and IP address of Windows PCs on its local network. If you connect to a remote network that contains a WINS server, enter the server’s IP address here. This allows your PCs to browse the network using the Network Neighborhood feature of Windows.Reserved IP addressesWhen you specify a reserved IP address for a computer on the LAN, that computer will always receive the same IP address each time it access the router’s DHCP server. Reserved IP addresses should be assigned to servers that require permanent IP settings. To reserve an IP address: 1. Click the Add button. 2. In the IP Address box, type the IP address to assign to the computer or server. Choose an IP address from the router’s LAN subnet, such as 192.168.0.x. 3. Type the MAC Address of the computer or server. Tip: If the computer is already present on your network, you can copy its MAC address from the Attached Devices menu and paste it here. 4. Click Apply to enter the reserved address into the table. Note: The reserved address will not be assigned until the next time the computer contacts the router's DHCP server. Reboot the computer or access its IP configuration and force a DHCP release and renew. To edit or delete a reserved address entry: 1. Click the button next to the reserved address you want to edit or delete. 2. Click Edit or Delete.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterAdvanced Configuration 7-7August 2004How to Configure LAN TCP/IP Settings1. Log in to the router at its default LAN address of http://192.168.0.1 with its default User Name of admin, default password of password, or using whatever User Name, Password and LAN address you have chosen for the router.2. From the Main Menu, under Advanced, click the LAN IP Setup link to view the menu, shown in Figure 7-3:.Figure 7-3: LAN IP Setup Menu3. Enter the TCP/IP, DHCP, or Reserved IP parameters.4. Click Apply to save your changes.Configuring Dynamic DNSIf your network has a permanently assigned IP address, you can register a domain name and have that name linked with your IP address by public Domain Name Servers (DNS). However, if your Internet account uses a dynamically assigned IP address, you will not know in advance what your IP address will be, and the address can change frequently. In this case, you can use a commercial dynamic DNS service that will allow you to register your domain to their IP address, and will forward traffic directed at your domain to your frequently-changing IP address.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router7-8 Advanced ConfigurationAugust 2004The router contains a client that can connect to a dynamic DNS service provider. To use this feature, you must select a service provider and obtain an account with them. After you have configured your account information in the router, whenever your ISP-assigned IP address changes, your router will automatically contact your dynamic DNS service provider, log in to your account, and register your new IP address.How to Configure Dynamic DNS1. Log in to the router at its default LAN address of http://192.168.0.1 with its default User Name of admin, default password of password, or using whatever User Name, Password and LAN address you have chosen for the router.2. From the Main Menu of the browser interface, under Advanced, select Dynamic DNS to display the page below.Figure 7-4: Dynamic DNS menu3. Access the Web site of one of the dynamic DNS service providers whose names appear in the ‘Service Provider’ box, and register for an account. For example, for dyndns.org, go to www.dyndns.org.4. Select the “Use a dynamic DNS service” check box. 5. Select the name of your dynamic DNS Service Provider. 6. Type the Host Name that your dynamic DNS service provider gave you. The dynamic DNS service provider may call this the domain name. If your URL is myName.dyndns.org, then your Host Name is “myName.”
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterAdvanced Configuration 7-9August 20047. Type the User Name for your dynamic DNS account. 8. Type the Password (or key) for your dynamic DNS account. 9. If your dynamic DNS provider allows the use of wildcards in resolving your URL, you can select the Use wildcards check box to activate this feature. For example, the wildcard feature will cause *.yourhost.dyndns.org to be aliased to the same IP address as yourhost.dyndns.org10. Click Apply to save your configuration. Using Static RoutesStatic Routes provide additional routing information to your router. Under normal circumstances, the router has adequate routing information after it has been configured for Internet access, and you do not need to configure additional static routes. You must configure static routes only for unusual cases such as multiple routers or multiple IP subnets located on your network.Static Route ExampleAs an example of when a static route is needed, consider the following case:• Your primary Internet access is through a cable modem to an ISP.• You have an ISDN router on your home network for connecting to the company where you are employed. This router’s address on your LAN is 192.168.0.100.• Your company’s network is 134.177.0.0.When you first configured your router, two implicit static routes were created. A default route was created with your ISP as the router, and a second static route was created to your local network for all 192.168.0.x addresses. With this configuration, if you attempt to access a device on the 134.177.0.0 network, your router will forward your request to the ISP. The ISP forwards your request to the company where you are employed, and the request will likely be denied by the company’s firewall.Note: If your ISP assigns a private WAN IP address such as 192.168.x.x or 10.x.x.x, the dynamic DNS service will not work because private addresses will not be routed on the Internet.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router7-10 Advanced ConfigurationAugust 2004In this case you must define a static route, telling your router that 134.177.0.0 should be accessed through the ISDN router at 192.168.0.100. The static route would look like Figure 7-6.In this example:• The Destination IP Address and IP Subnet Mask fields specify that this static route applies to all 134.177.x.x addresses. • The Router IP Address fields specifies that all traffic for these addresses should be forwarded to the ISDN router at 192.168.0.100. • A Metric value of 1 will work since the ISDN router is on the LAN. This represents the number of routers between your network and the destination. This is a direct connection so it is set to 1.• Private is selected only as a precautionary security measure in case RIP is activated.How to Configure Static Routes1. Log in to the router at its default LAN address of http://192.168.0.1 with its default User Name of admin, default password of password, or using whatever User Name, Password and LAN address you have chosen for the router.2. From the Main Menu of the browser interface, under Advanced, click Static Routes to view the Static Routes menu, shown in Figure 7-5. Figure 7-5: Static Routes Table
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterAdvanced Configuration 7-11August 20043. To add or edit a Static Route:a. Click the Edit button to open the Edit Menu, shown in Figure 7-6.Figure 7-6: Static Route Entry and Edit Menub. Type a route name for this static route in the Route Name box under the table. This is for identification purpose only. c. Select Private if you want to limit access to the LAN only. The static route will not be reported in RIP. d. Select Active to make this route effective. e. Type the Destination IP Address of the final destination. f. Type the IP Subnet Mask for this destination. If the destination is a single host, type 255.255.255.255. g. Type the Gateway IP Address, which must be a router on the same LAN segment as the router. h. Type a number between 1 and 15 as the Metric value. This represents the number of routers between your network and the destination. Usually, a setting of 2 or 3 works, but if this is a direct connection, set it to 1. 4. Click Apply to have the static route entered into the table.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router7-12 Advanced ConfigurationAugust 2004
Troubleshooting 8-1August 2004Chapter 8 TroubleshootingThis chapter gives information about troubleshooting your DG834GT 108 Mbps Super Wireless ADSL Router. After each problem description, instructions are provided to help you diagnose and solve the problem. For the common problems listed, go to the section indicated.• Is the router on?• Have I connected the router correctly?Go to “Basic Functioning” on page 8-1.• I can’t access the router’s configuration with my browser.Go to “Troubleshooting the Web Configuration Interface” on page 8-3.• I’ve configured the router but I can’t access the Internet.Go to “Troubleshooting the ISP Connection” on page 8-4.• I can’t remember the router’s configuration password.• I want to clear the configuration and start over again.Go to “Restoring the Default Configuration and Password” on page 8-9.Basic FunctioningAfter you turn on power to the router, the following sequence of events should occur:1. When power is first applied, verify that the Power LED is on (see “The Router’s Front Panel” on page 2-6 for an illustration and explanation of the LEDs).2. Verify that the Test LED lights within a few seconds, indicating that the self-test procedure is running.3. After approximately 10 seconds, verify that:a. The Test LED is not lit.b. The LAN port LEDs are lit for any local ports that are connected.c. The WAN port LED is lit.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router8-2 TroubleshootingAugust 2004If a port’s LED is lit, a link has been established to the connected device. If a LAN port is connected to a 100 Mbps device, verify that the port’s LED is green. If the port is 10 Mbps, the LED will be amber.If any of these conditions does not occur, refer to the appropriate following section.Power LED Not OnIf the Power and other LEDs are off when your router is turned on:• Make sure that the power cord is properly connected to your router and that the power supply adapter is properly connected to a functioning power outlet. • Check that you are using the 12 V DC power adapter supplied by NETGEAR for this product.If the error persists, you have a hardware problem and should contact technical support.Test LED Never Turns On or Test LED Stays OnWhen the router is turned on, the Test LED turns on for about 10 seconds and then turns off. If the Test LED does not turn on, or if it stays on, there is a fault within the router.If you experience problems with the Test LED:• Cycle the power to see if the router recovers and the LED blinks for the correct amount of time.If all LEDs including the Test LED are still on one minute after power up:• Cycle the power to see if the router recovers.• Clear the router’s configuration to factory defaults. This will set the router’s IP address to 192.168.0.1. This procedure is explained in “Using the Reset button” on page 8-9.If the error persists, you might have a hardware problem and should contact technical support.LAN or WAN Port LEDs Not OnIf either the LAN LEDs or WAN LED do not light when the Ethernet connection is made, check the following:• Make sure that the Ethernet cable connections are secure at the router and at the hub or workstation.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterTroubleshooting 8-3August 2004• Make sure that power is turned on to the connected hub or workstation.• Be sure you are using the correct cable:— When connecting the router’s WAN ADSL port, use the cable that was supplied with the DG834GT. Troubleshooting the Web Configuration InterfaceIf you are unable to access the router’s Web Configuration interface from a computer on your local network, check the following:• If you are using an Ethernet-connected computer, check the Ethernet connection between the computer and the router as described in the previous section.• Make sure your computer’s IP address is on the same subnet as the router. If you are using the recommended addressing scheme, your computer’s address should be in the range of 192.168.0.2 to 192.168.0.254. Refer to “Verifying TCP/IP Properties” on page C-6 or “Verifying TCP/IP Properties for Macintosh Computers” on page C-17 to find your computer’s IP address. Follow the instructions in Appendix C to configure your computer.Note: If your computer’s IP address is shown as 169.254.x.x: Recent versions of Windows and MacOS will generate and assign an IP address if the computer cannot reach a DHCP server. These auto-generated addresses are in the range of 169.254.x.x. If your IP address is in this range, check the connection from the computer to the router and reboot your computer.• If your router’s IP address was changed and you do not know the current IP address, clear the router’s configuration to factory defaults. This will set the router’s IP address to 192.168.0.1. This procedure is explained in “Using the Reset button” on page 8-9.• Make sure your browser has Java, JavaScript, or ActiveX enabled. If you are using Internet Explorer, click Refresh to be sure the Java applet is loaded.• Try quitting the browser and launching it again.• Make sure you are using the correct login information. The factory default login name is admin and the password is password. Make sure that CAPS LOCK is off when entering this information.If the router does not save changes you have made in the Web Configuration Interface, check the following:• When entering configuration settings, be sure to click the APPLY button before moving to another menu or tab, or your changes are lost.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router8-4 TroubleshootingAugust 2004• Click the Refresh or Reload button in the Web browser. The changes may have occurred, but the Web browser may be caching the old configuration.Troubleshooting the ISP ConnectionIf your router is unable to access the Internet, you should check the ADSL connection, then the WAN TCP/IP connection. ADSL linkIf your router is unable to access the Internet, you should first determine whether you have an ADSL link with the service provider. The state of this connection is indicated with the WAN LED.WAN LED Green or Blinking GreenIf your WAN LED is green or blinking green, then you have a good ADSL connection. You can be confident that the service provider has connected your line correctly and that your wiring is correct.WAN LED Blinking YellowIf your WAN LED is blinking yellow, then your router is attempting to make an ADSL connection with the service provider. The LED should turn green within several minutes. If the WAN LED does not turn green, disconnect all telephones on the line. If this solves the problem, reconnect the telephones one at a time, being careful to use a microfilter on each telephone. If the microfilters are connected correctly, you should be able to connect all your telephones.If disconnecting telephones does not result in a green WAN LED, there may be a problem with your wiring. If the telephone company has tested the ADSL signal at your Network Interface Device (NID), then you may have poor quality wiring in your house.WAN LED OffIf the WAN LED is off, disconnect all telephones on the line. If this solves the problem, reconnect the telephones one at a time, being careful to use a microfilter on each telephone. If the microfilters are connected correctly, you should be able to connect all your telephones.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterTroubleshooting 8-5August 2004If disconnecting telephones does not result in a green WAN LED the problem may be one of the following:• Check that the telephone company has made the connection to your line and tested it.• Verify that you are connected to the correct telephone line. If you have more than one phone line, be sure that you are connected to the line with the ADSL service. It may be necessary to use a swapper if you ADSL signal is on pins 1 and 4 or the RJ-11 jack. The DG834GT Super Wireless ADSL Router uses pins 2 and 3.Obtaining a WAN IP AddressIf your router is unable to access the internet, and your WAN LED is green or blinking green, you should determine whether the router is able to obtain a WAN IP address from the ISP. Unless you have been assigned a static IP address, your router must request an IP address from the ISP. You can determine whether the request was successful using the browser interface.To check the WAN IP address from the browser interface: 1. Launch your browser and select an external site such as www.netgear.com.2. Access the Main Menu of the router’s configuration at http://192.168.0.1. 3. Under the Maintenance heading check that an IP address is shown for the WAN Port. If 0.0.0.0 is shown, your router has not obtained an IP address from your ISP.If your router is unable to obtain an IP address from the ISP, the problem may be one of the following:• Your ISP may require a Multiplexing Method or Virtual Path Identifier/Virtual Channel Identifier parameter. Verify with your ISP the Multiplexing Method and parameter value, and update the router’s ADSL Settings accordingly.• Your ISP may require a login program. Ask your ISP whether they require PPP over Ethernet (PPPoE) or PPP over ATM (PPPOA) login.• If you have selected a login program, you may have incorrectly set the Service Name, User Name and Password. See “Troubleshooting PPPoE or PPPoA”, below.• Your ISP may check for your computer's host name. Assign the computer Host Name of your ISP account to the router in the browser-based Setup Wizard.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router8-6 TroubleshootingAugust 2004• Your ISP only allows one Ethernet MAC address to connect to Internet, and may check for your computer’s MAC address. In this case:Inform your ISP that you have bought a new network device, and ask them to use the router’s MAC address.ORConfigure your router to spoof your computer’s MAC address. This can be done in the Basic Settings menu. Refer to “Manually Configuring Your Internet Connection” on page 3-15.Troubleshooting PPPoE or PPPoAThe PPPoA or PPPoA connection can be debugged as follows:1. Access the Main Menu of the router at http://192.168.0.1.2. Under the Maintenance heading, select the Router Status link.3. Click the Connection Status button.4. If all of the steps indicate “OK” then your PPPoE or PPPoA connection is up and working.5. If any of the steps indicates “Failed”, you can attempt to reconnect by clicking “Connect”. The router will continue to attempt to connect indefinitely.If you cannot connect after several minutes, you may be using an incorrect Service Name, User Name or Password. There also may be a provisioning problem with your ISP.Troubleshooting Internet BrowsingIf your router can obtain an IP address but your computer is unable to load any Web pages from the Internet:• Your computer may not recognize any DNS server addresses. Note: Unless you connect manually, the router will not authenticate using PPPoE or PPPoA until data is transmitted to the network.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterTroubleshooting 8-7August 2004A DNS server is a host on the Internet that translates Internet names (such as www addresses) to numeric IP addresses. Typically your ISP will provide the addresses of one or two DNS servers for your use. If you entered a DNS address during the router’s configuration, reboot your computer and verify the DNS address as described in “Verifying TCP/IP Properties” on page C-6. Alternatively, you can configure your computer manually with DNS addresses, as explained in your operating system documentation.• Your computer may not have the router configured as its TCP/IP router.If your computer obtains its information from the router by DHCP, reboot the computer and verify the router address as described in “Verifying TCP/IP Properties” on page C-6.Troubleshooting a TCP/IP Network Using the Ping UtilityMost TCP/IP terminal devices and routers contain a ping utility that sends an echo request packet to the designated device. The device then responds with an echo reply. Troubleshooting a TCP/IP network is made very easy by using the ping utility in your computer.Testing the LAN Path to Your RouterYou can ping the router from your computer to verify that the LAN path to your router is set up correctly.To ping the router from a PC running Windows 95 or later:1. From the Windows toolbar, click the Start button and select Run.2. In the field provided, type Ping followed by the IP address of the router, as in this example:ping 192.168.0.13. Click OK.You should see a message like this one:Pinging <IP address> with 32 bytes of dataIf the path is working, you see this message:Reply from < IP address >: bytes=32 time=NN ms TTL=xxxIf the path is not working, you see this message:Request timed outIf the path is not functioning correctly, you could have one of the following problems:
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router8-8 TroubleshootingAugust 2004• Wrong physical connections— Make sure the LAN port LED is on. If the LED is off, follow the instructions in “LAN or WAN Port LEDs Not On” on page 8-2.— Check that the corresponding Link LEDs are on for your network interface card and for the hub ports (if any) that are connected to your workstation and router.• Wrong network configuration— Verify that the Ethernet card driver software and TCP/IP software are both installed and configured on your PC or workstation.— Verify that the IP address for your router and your workstation are correct and that the addresses are on the same subnet.Testing the Path from Your Computer to a Remote DeviceAfter verifying that the LAN path works correctly, test the path from your PC to a remote device. From the Windows run menu, type:PING -n 10 <IP address>where <IP address> is the IP address of a remote device such as your ISP’s DNS server.If the path is functioning correctly, replies as in the previous section are displayed. If you do not receive replies:— Check that your PC has the IP address of your router listed as the default router. If the IP configuration of your PC is assigned by DHCP, this information will not be visible in your PC’s Network Control Panel. Verify that the IP address of the router is listed as the default router as described in “Verifying TCP/IP Properties” on page C-6.— Check to see that the network address of your PC (the portion of the IP address specified by the netmask) is different from the network address of the remote device.— Check that your cable or DSL modem is connected and functioning.— If your ISP assigned a host name to your PC, enter that host name as the Account Name in the Basic Settings menu.— Your ISP could be rejecting the Ethernet MAC addresses of all but one of your PCs. Many broadband ISPs restrict access by only allowing traffic from the MAC address of your broadband modem, but some ISPs additionally restrict access to the MAC address of a single PC connected to that modem. If this is the case, you must configure your router to “clone” or “spoof” the MAC address from the authorized PC. Refer to “Manually Configuring Your Internet Connection” on page 3-15.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterTroubleshooting 8-9August 2004Restoring the Default Configuration and PasswordThis section explains how to restore the factory default configuration settings, changing the router’s administration password to password and the IP address to 192.168.0.1. You can erase the current configuration and restore factory defaults in two ways:• Use the Erase function of the Web Configuration Manager (see “Backing Up, Restoring, or Erasing Your Settings” on page 6-1).• Use the Default Reset button on the rear panel of the router. Use this method for cases when the administration password or IP address is not known.Using the Reset buttonTo restore the factory default configuration settings without knowing the administration password or IP address, you must use the Default Reset button on the rear panel of the router.1. Press and hold the Default Reset button until the Test LED turns on (about 10 seconds).2. Release the Default Reset button and wait for the router to reboot.Problems with Date and TimeThe E-mail menu in the Content Filtering section displays the current date and time of day. The DG834GT Super Wireless ADSL Router uses the Network Time Protocol (NTP) to obtain the current time from one of several Network Time Servers on the Internet. Each entry in the log is stamped with the date and time of day. Problems with the date and time function can include:• Date shown is January 1, 2000 Cause: The router has not yet successfully reached a Network Time Server. Check that your Internet access settings are configured correctly. If you have just completed configuring the router, wait at least five minutes and check the date and time again.• Time is off by one hour Cause: The router does not automatically sense Daylight Savings Time. In the E-mail menu, check or uncheck the box marked “Adjust for Daylight Savings Time”.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router8-10 TroubleshootingAugust 2004
Technical Specifications A-1August 2004Appendix ATechnical SpecificationsThis appendix provides technical specifications for the DG834GT 108 Mbps Super Wireless ADSL Router.Network Protocol and Standards CompatibilityData and Routing Protocols: TCP/IP, RIP-1, RIP-2, DHCP, PPP over Ethernet (PPPoE) or PPP over ATM (PPPoA), RFC 1483 Bridged or Routed Ethernet, and RFC 1577 Classical IP over ATMPower AdapterNorth America: 120V, 60 Hz, inputUnited Kingdom, Australia: 240V, 50 Hz, inputEurope: 230V, 50 Hz, inputJapan: 100V, 50/60 Hz, inputAll regions (output): 15 V DC @ 1.0A output, 30W maximumPhysical SpecificationsDimensions: 10" x 6.7" x 1.3" 255 mm x 169 mm x 34 mmWeight: 1.4 lbs. 0.62 kgEnvironmental SpecificationsOperating temperature: 0° to 40° C (32º to 104º F)Operating humidity: 90% maximum relative humidity, noncondensing
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterA-2 Technical SpecificationsAugust 2004Electromagnetic EmissionsMeets requirements of: FCC Part 15 Class BVCCI Class BEN 55 022 (CISPR 22), Class BInterface SpecificationsLAN: 10BASE-T or 100BASE-Tx, RJ-45WAN: ADSL, RJ-11, pins 2 and 3 T1.413, G.DMT, G.Lite ITU Annex A (model DG834GT) or B (model DG834GTB)
Network and Routing Basics B-1August 2004Appendix BNetwork and Routing BasicsThis chapter provides an overview of IP networks and routing.Related PublicationsAs you read this document, you may be directed to various RFC documents for further information. An RFC is a Request For Comment (RFC) published by the Internet Engineering Task Force (IETF), an open organization that defines the architecture and operation of the Internet. The RFC documents outline and define the standard protocols and procedures for the Internet. The documents are listed on the World Wide Web at www.ietf.org and are mirrored and indexed at many other sites worldwide.Basic Router ConceptsLarge amounts of bandwidth can be provided easily and relatively inexpensively in a local area network (LAN). However, providing high bandwidth between a local network and the Internet can be very expensive. Because of this expense, Internet access is usually provided by a slower-speed wide-area network (WAN) link such as a cable or DSL modem. In order to make the best use of the slower WAN link, a mechanism must be in place for selecting and transmitting only the data traffic meant for the Internet. The function of selecting and forwarding this data is performed by a router.What is a Router?A router is a device that forwards traffic between networks based on network layer information in the data and on routing tables maintained by the router. In these routing tables, a router builds up a logical picture of the overall network by gathering and exchanging information with other routers in the network. Using this information, the router chooses the best path for forwarding network traffic.Routers vary in performance and scale, number of routing protocols supported, and types of physical WAN connection they support. The DG834GT 108 Mbps Super Wireless ADSL Router is a small office router that routes the IP protocol over a single-user broadband connection.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterB-2 Network and Routing BasicsAugust 2004Routing Information ProtocolOne of the protocols used by a router to build and maintain a picture of the network is the Routing Information Protocol (RIP). Using RIP, routers periodically update one another and check for changes to add to the routing table.The DG834GT Super Wireless ADSL Router supports both the older RIP-1 and the newer RIP-2 protocols. Among other improvements, RIP-2 supports subnet and multicast protocols. RIP is not required for most home applications. IP Addresses and the InternetBecause TCP/IP networks are interconnected across the world, every machine on the Internet must have a unique address to make sure that transmitted data reaches the correct destination. Blocks of addresses are assigned to organizations by the Internet Assigned Numbers Authority (IANA). Individual users and small organizations may obtain their addresses either from the IANA or from an Internet service provider (ISP). You can contact IANA at www.iana.org.The Internet Protocol (IP) uses a 32-bit address structure. The address is usually written in dot notation (also called dotted-decimal notation), in which each group of eight bits is written in decimal form, separated by decimal points.For example, the following binary address: 11000011 00100010 00001100 00000111 is normally written as: 195.34.12.7The latter version is easier to remember and easier to enter into your computer.In addition, the 32 bits of the address are subdivided into two parts. The first part of the address identifies the network, and the second part identifies the host node or station on the network. The dividing point may vary depending on the address range and the application.There are five standard classes of IP addresses. These address classes have different ways of determining the network and host sections of the address, allowing for different numbers of hosts on a network. Each address type begins with a unique bit pattern, which is used by the TCP/IP software to identify the address class. After the address class has been determined, the software can correctly identify the host section of the address. The follow figure shows the three main address classes, including network and host sections of the address for each address type.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterNetwork and Routing Basics B-3August 2004Figure 8-1: Three Main Address ClassesThe five address classes are:• Class A Class A addresses can have up to 16,777,214 hosts on a single network. They use an eight-bit network number and a 24-bit node number. Class A addresses are in this range: 1.x.x.x to 126.x.x.x. • Class B Class B addresses can have up to 65,354 hosts on a network. A Class B address uses a 16-bit network number and a 16-bit node number. Class B addresses are in this range: 128.1.x.x to 191.254.x.x. • Class C Class C addresses can have 254 hosts on a network. Class C addresses use 24 bits for the network address and eight bits for the node. They are in this range:192.0.1.x to 223.255.254.x. • Class D Class D addresses are used for multicasts (messages sent to many hosts). Class D addresses are in this range:224.0.0.0 to 239.255.255.255. • Class E Class E addresses are for experimental use. Class ANetwork NodeClass BClass CNetwork NodeNetwork Node
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterB-4 Network and Routing BasicsAugust 2004This addressing structure allows IP addresses to uniquely identify each physical network and each node on each physical network.For each unique value of the network portion of the address, the base address of the range (host address of all zeros) is known as the network address and is not usually assigned to a host. Also, the top address of the range (host address of all ones) is not assigned, but is used as the broadcast address for simultaneously sending a packet to all hosts with the same network address.NetmaskIn each of the address classes previously described, the size of the two parts (network address and host address) is implied by the class. This partitioning scheme can also be expressed by a netmask associated with the IP address. A netmask is a 32-bit quantity that, when logically combined (using an AND operator) with an IP address, yields the network address. For instance, the netmasks for Class A, B, and C addresses are 255.0.0.0, 255.255.0.0, and 255.255.255.0, respectively.For example, the address 192.168.170.237 is a Class C IP address whose network portion is the upper 24 bits. When combined (using an AND operator) with the Class C netmask, as shown here, only the network portion of the address remains:11000000 10101000 10101010 11101101 (192.168.170.237)combined with:11111111 11111111 11111111 00000000 (255.255.255.0)Equals:11000000 10101000 10101010 00000000 (192.168.170.0)As a shorter alternative to dotted-decimal notation, the netmask may also be expressed in terms of the number of ones from the left. This number is appended to the IP address, following a backward slash (/), as “/n.” In the example, the address could be written as 192.168.170.237/24, indicating that the netmask is 24 ones followed by 8 zeros. Subnet AddressingBy looking at the addressing structures, you can see that even with a Class C address, there are a large number of hosts per network. Such a structure is an inefficient use of addresses if each end of a routed link requires a different network number. It is unlikely that the smaller office LANs would have that many devices. You can resolve this problem by using a technique known as subnet addressing.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterNetwork and Routing Basics B-5August 2004Subnet addressing allows us to split one IP network address into smaller multiple physical networks known as subnetworks. Some of the node numbers are used as a subnet number instead. A Class B address gives us 16 bits of node numbers translating to 64,000 nodes. Most organizations do not use 64,000 nodes, so there are free bits that can be reassigned. Subnet addressing makes use of those bits that are free, as shown below.Figure 8-2: Example of Subnetting a Class B AddressA Class B address can be effectively translated into multiple Class C addresses. For example, the IP address of 172.16.0.0 is assigned, but node addresses are limited to 255 maximum, allowing eight extra bits to use as a subnet address. The IP address of 172.16.97.235 would be interpreted as IP network address 172.16, subnet number 97, and node number 235. In addition to extending the number of addresses available, subnet addressing provides other benefits. Subnet addressing allows a network manager to construct an address scheme for the network by using different subnets for other geographical locations in the network or for other departments in the organization.Although the preceding example uses the entire third octet for a subnet address, note that you are not restricted to octet boundaries in subnetting. To create more network numbers, you need only shift some bits from the host address to the network address. For instance, to partition a Class C network number (192.68.135.0) into two, you shift one bit from the host address to the network address. The new netmask (or subnet mask) is 255.255.255.128. The first subnet has network number 192.68.135.0 with hosts 192.68.135.1 to 129.68.135.126, and the second subnet has network number 192.68.135.128 with hosts 192.68.135.129 to 192.68.135.254.The following table lists the additional subnet mask bits in dotted-decimal notation. To use the table, write down the original class netmask and replace the 0 value octets with the dotted-decimal value of the additional subnet bits. For example, to partition your Class C network with subnet mask 255.255.255.0 into 16 subnets (4 bits), the new subnet mask becomes 255.255.255.240.Note: The number 192.68.135.127 is not assigned because it is the broadcast address of the first subnet. The number 192.68.135.128 is not assigned because it is the network address of the second subnet.7262Class BNetwork Subnet Node
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterB-6 Network and Routing BasicsAugust 2004The following table displays several common netmask values in both the dotted-decimal and the masklength formats.NETGEAR strongly recommends that you configure all hosts on a LAN segment to use the same netmask for the following reasons:• So that hosts recognize local IP broadcast packetsTable 8-1. Netmask Notation Translation Table for One OctetNumber of Bits Dotted-Decimal Value1 1282 1923 2244 2405 2486 2527 2548 255Table 8-2. Netmask FormatsDotted-Decimal Masklength255.0.0.0 /8255.255.0.0 /16255.255.255.0 /24255.255.255.128 /25255.255.255.192 /26255.255.255.224 /27255.255.255.240 /28255.255.255.248 /29255.255.255.252 /30255.255.255.254 /31255.255.255.255 /32
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterNetwork and Routing Basics B-7August 2004When a device broadcasts to its segment neighbors, it uses a destination address of the local network address with all ones for the host address. In order for this scheme to work, all devices on the segment must agree on which bits comprise the host address. • So that a local router or bridge recognizes which addresses are local and which are remotePrivate IP AddressesIf your local network is isolated from the Internet (for example, when using NAT), you can assign any IP addresses to the hosts without problems. However, the IANA has reserved the following three blocks of IP addresses specifically for private networks:10.0.0.0 - 10.255.255.255172.16.0.0 - 172.31.255.255192.168.0.0 - 192.168.255.255NETGEAR recommends that you choose your private network number from this range. The DHCP server of the DG834GT Super Wireless ADSL Router is preconfigured to automatically assign private addresses.Regardless of your particular situation, do not create an arbitrary IP address; always follow the guidelines explained here. For more information about address assignment, refer to RFC 1597, Address Allocation for Private Internets, and RFC 1466, Guidelines for Management of IP Address Space. The Internet Engineering Task Force (IETF) publishes RFCs on its Web site at www.ietf.org.Single IP Address Operation Using NATIn the past, if multiple PCs on a LAN needed to access the Internet simultaneously, you had to obtain a range of IP addresses from the ISP. This type of Internet account is more costly than a single-address account typically used by a single user with a modem, rather than a router. The DG834GT Super Wireless ADSL Router employs an address-sharing method called Network Address Translation (NAT). This method allows several networked PCs to share an Internet account using only a single IP address, which may be statically or dynamically assigned by your ISP.The router accomplishes this address sharing by translating the internal LAN IP addresses to a single address that is globally unique on the Internet. The internal LAN IP addresses can be either private addresses or registered addresses. For more information about IP address translation, refer to RFC 1631, The IP Network Address Translator (NAT).The following figure illustrates a single IP address operation.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterB-8 Network and Routing BasicsAugust 2004 Figure 8-3: Single IP Address Operation Using NATThis scheme offers the additional benefit of firewall-like protection because the internal LAN addresses are not available to the Internet through the translated connection. All incoming inquiries are filtered out by the router. This filtering can prevent intruders from probing your system. However, using port forwarding, you can allow one PC (for example, a Web server) on your local network to be accessible to outside users.MAC Addresses and Address Resolution ProtocolAn IP address alone cannot be used to deliver data from one LAN device to another. To send data between LAN devices, you must convert the IP address of the destination device to its media access control (MAC) address. Each device on an Ethernet network has a unique MAC address, which is a 48-bit number assigned to each device by the manufacturer. The technique that associates the IP address with a MAC address is known as address resolution. Internet Protocol uses the Address Resolution Protocol (ARP) to resolve MAC addresses.If a device sends data to another station on the network and the destination MAC address is not yet recorded, ARP is used. An ARP request is broadcast onto the network. All stations on the network receive and read the request. The destination IP address for the chosen station is included as part of the message so that only the station with this IP address responds to the ARP request. All other stations discard the request. 7786EA192.168.0.2192.168.0.3192.168.0.4192.168.0.5192.168.0.1 172.21.15.105Private IP addressesassigned by userInternetIP addressesassigned by ISP
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterNetwork and Routing Basics B-9August 2004Related DocumentsThe station with the correct IP address responds with its own MAC address directly to the sending device. The receiving station provides the transmitting station with the required destination MAC address. The IP address data and MAC address data for each station are held in an ARP table. The next time data is sent, the address can be obtained from the address information in the table.For more information about address assignment, refer to the IETF documents RFC 1597, Address Allocation for Private Internets, and RFC 1466, Guidelines for Management of IP Address Space.For more information about IP address translation, refer to RFC 1631, The IP Network Address Translator (NAT).Domain Name ServerMany of the resources on the Internet can be addressed by simple descriptive names such as www.NETGEAR.com. This addressing is very helpful at the application level, but the descriptive name must be translated to an IP address in order for a user to actually contact the resource. Just as a telephone directory maps names to phone numbers, or as an ARP table maps IP addresses to MAC addresses, a domain name system (DNS) server maps descriptive names of network resources to IP addresses.When a PC accesses a resource by its descriptive name, it first contacts a DNS server to obtain the IP address of the resource. The PC sends the desired message using the IP address. Many large organizations, such as ISPs, maintain their own DNS servers and allow their customers to use the servers to look up addresses.IP Configuration by DHCPWhen an IP-based local area network is installed, each PC must be configured with an IP address. If the PCs need to access the Internet, they should also be configured with a gateway address and one or more DNS server addresses. As an alternative to manual configuration, there is a method by which each PC on the network can automatically obtain this configuration information. A device on the network may act as a Dynamic Host Configuration Protocol (DHCP) server. The DHCP server stores a list or pool of IP addresses, along with other information (such as gateway and DNS addresses) that it may assign to the other devices on the network. The DG834GT Super Wireless ADSL Router has the capacity to act as a DHCP server.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterB-10 Network and Routing BasicsAugust 2004The DG834GT Super Wireless ADSL Router also functions as a DHCP client when connecting to the ISP. The router can automatically obtain an IP address, subnet mask, DNS server addresses, and a gateway address if the ISP provides this information by DHCP.Internet Security and FirewallsWhen your LAN connects to the Internet through a router, an opportunity is created for outsiders to access or disrupt your network. A NAT router provides some protection because by the very nature of the Network Address Translation (NAT) process, the network behind the NAT router is shielded from access by outsiders on the Internet. However, there are methods by which a determined hacker can possibly obtain information about your network or at the least can disrupt your Internet access. A greater degree of protection is provided by a firewall router.What is a Firewall?A firewall is a device that protects one network from another, while allowing communication between the two. A firewall incorporates the functions of the NAT router, while adding features for dealing with a hacker intrusion or attack. Several known types of intrusion or attack can be recognized when they occur. When an incident is detected, the firewall can log details of the attempt, and can optionally send email to an administrator notifying them of the incident. Using information from the log, the administrator can take action with the ISP of the hacker. In some types of intrusions, the firewall can fend off the hacker by discarding all further packets from the hacker’s IP address for a period of time.Stateful Packet InspectionUnlike simple Internet sharing routers, a firewall uses a process called stateful packet inspection to ensure secure firewall filtering to protect your network from attacks and intrusions. Since user-level applications such as FTP and Web browsers can create complex patterns of network traffic, it is necessary for the firewall to analyze groups of network connection states. Using Stateful Packet Inspection, an incoming packet is intercepted at the network layer and then analyzed for state-related information associated with all network connections. A central cache within the firewall keeps track of the state information associated with all network connections. All traffic passing through the firewall is analyzed against the state of these connections in order to determine whether or not it will be allowed to pass through or rejected.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterNetwork and Routing Basics B-11August 2004Denial of Service AttackA hacker may be able to prevent your network from operating or communicating by launching a Denial of Service (DoS) attack. The method used for such an attack can be as simple as merely flooding your site with more requests than it can handle. A more sophisticated attack may attempt to exploit some weakness in the operating system used by your router or gateway. Some operating systems can be disrupted by simply sending a packet with incorrect length information.Ethernet CablingAlthough Ethernet networks originally used thick or thin coaxial cable, most installations currently use unshielded twisted pair (UTP) cabling. The UTP cable contains eight conductors, arranged in four twisted pairs, and terminated with an RJ45 type connector. A normal straight-through UTP Ethernet cable follows the EIA568B standard wiring as described below in Table B-1.Category 5 Cable QualityCategory 5 distributed cable that meets ANSI/EIA/TIA-568-A building wiring standards can be a maximum of 328 feet (ft.) or 100 meters (m) in length, divided as follows:20 ft. (6 m) between the hub and the patch panel (if used)295 ft. (90 m) from the wiring closet to the wall outletTable B-1. UTP Ethernet cable wiring, straight-throughPin Wire color Signal1 Orange/White Transmit (Tx) +2 Orange Transmit (Tx) -3 Green/White Receive (Rx) +4Blue5 Blue/White6 Green Receive (Rx) -7 Brown/White8Brown
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterB-12 Network and Routing BasicsAugust 200410 ft. (3 m) from the wall outlet to the desktop deviceThe patch panel and other connecting hardware must meet the requirements for 100 Mbps operation (Category 5). Only 0.5 inch (1.5 cm) of untwist in the wire pair is allowed at any termination point.A twisted pair Ethernet network operating at 10 Mbits/second (10BASE-T) will often tolerate low quality cables, but at 100 Mbits/second (10BASE-Tx) the cable must be rated as Category 5, or Cat 5, by the Electronic Industry Association (EIA). This rating will be printed on the cable jacket. A Category 5 cable will meet specified requirements regarding loss and crosstalk. In addition, there are restrictions on maximum cable length for both 10 and 100 Mbits/second networks.Inside Twisted Pair CablesFor two devices to communicate, the transmitter of each device must be connected to the receiver of the other device. The crossover function is usually implemented internally as part of the circuitry in the device. Computers and workstation adapter cards are usually media-dependent interface ports, called MDI or uplink ports. Most repeaters and switch ports are configured as media-dependent interfaces with built-in crossover ports, called MDI-X or normal ports. Auto Uplink technology automatically senses which connection, MDI or MDI-X, is needed and makes the right connection.Figure B-1 illustrates straight-through twisted pair cable.Figure B-1: Straight-Through Twisted-Pair CableFigure B-2 illustrates crossover twisted pair cable.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterNetwork and Routing Basics B-13August 2004Figure B-2: Crossover Twisted-Pair CableFigure B-3: Category 5 UTP Cable with Male RJ-45 Plug at Each EndNote: Flat “silver satin” telephone cable may have the same RJ-45 plug. However, using telephone cable results in excessive collisions, causing the attached port to be partitioned or disconnected from the network.Uplink Switches, Crossover Cables, and MDI/MDIX SwitchingIn the wiring table above, the concept of transmit and receive are from the perspective of the PC, which is wired as Media Dependant Interface (MDI). In this wiring, the PC transmits on pins 1 and 2. At the hub, the perspective is reversed, and the hub receives on pins 1 and 2. This wiring is referred to as Media Dependant Interface - Crossover (MDI-X).
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterB-14 Network and Routing BasicsAugust 2004When connecting a PC to a PC, or a hub port to another hub port, the transmit pair must be exchanged with the receive pair. This exchange is done by one of two mechanisms. Most hubs provide an Uplink switch which will exchange the pairs on one port, allowing that port to be connected to another hub using a normal Ethernet cable. The second method is to use a crossover cable, which is a special cable in which the transmit and receive pairs are exchanged at one of the two cable connectors. Crossover cables are often unmarked as such, and must be identified by comparing the two connectors. Since the cable connectors are clear plastic, it is easy to place them side by side and view the order of the wire colors on each. On a straight-through cable, the color order will be the same on both connectors. On a crossover cable, the orange and blue pairs will be exchanged from one connector to the other.The DG834GT Super Wireless ADSL Router incorporates Auto UplinkTM technology (also called MDI/MDIX). Each LOCAL Ethernet port will automatically sense whether the Ethernet cable plugged into the port should have a normal connection (e.g. connecting to a PC) or an uplink connection (e.g. connecting to a router, switch, or hub). That port will then configure itself to the correct configuration. This feature also eliminates the need to worry about crossover cables, as Auto UplinkTM will accommodate either type of cable to make the right connection.
Preparing Your Network C-1August 2004Appendix CPreparing Your NetworkThis appendix describes how to prepare your network to connect to the Internet through the DG834GT 108 Mbps Super Wireless ADSL Router and how to verify the readiness of broadband Internet service from an Internet service provider (ISP).Preparing Your Computers for TCP/IP NetworkingComputers access the Internet using a protocol called TCP/IP (Transmission Control Protocol/Internet Protocol). Each computer on your network must have TCP/IP installed and selected as its networking protocol. If a Network Interface Card (NIC) is already installed in your PC, then TCP/IP is probably already installed as well.Most operating systems include the software components you need for networking with TCP/IP:•Windows® 95 or later includes the software components for establishing a TCP/IP network. • Windows 3.1 does not include a TCP/IP component. You need to purchase a third-party TCP/IP application package such as NetManage Chameleon.• Macintosh Operating System 7 or later includes the software components for establishing a TCP/IP network.• All versions of UNIX or Linux include TCP/IP components. Follow the instructions provided with your operating system or networking software to install TCP/IP on your computer.Note: If an ISP technician configured your computer during the installation of a broadband modem, or if you configured it using instructions provided by your ISP, you may need to copy the current configuration information for use in the configuration of your router. Write down this information before reconfiguring your computers. Refer to “Obtaining ISP Configuration Information for Windows Computers” on page C-19 or “Obtaining ISP Configuration Information for Macintosh Computers” on page C-20 for further information.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterC-2 Preparing Your NetworkAugust 2004In your IP network, each PC and the router must be assigned a unique IP addresses. Each PC must also have certain other IP configuration information such as a subnet mask (netmask), a domain name server (DNS) address, and a default gateway address. In most cases, you should install TCP/IP so that the PC obtains its specific network configuration information automatically from a DHCP server during bootup. For a detailed explanation of the meaning and purpose of these configuration items, refer to “Appendix B, “Network and Routing Basics.” The DG834GT Super Wireless ADSL Router is shipped preconfigured as a DHCP server. The router assigns the following TCP/IP configuration information automatically when the PCs are rebooted:• PC or workstation IP addresses—192.168.0.2 through 192.168.0.254• Subnet mask—255.255.255.0• Gateway address (the router)—192.168.0.1These addresses are part of the IETF-designated private address range for use in private networks.Configuring Windows 95, 98, and Me for TCP/IP NetworkingAs part of the PC preparation process, you need to manually install and configure TCP/IP on each networked PC. Before starting, locate your Windows CD; you may need to insert it during the TCP/IP installation process.Installing or Verifying Windows Networking ComponentsTo install or verify the necessary components for IP networking:1. On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.2. Double-click the Network icon.The Network window opens, which displays a list of installed components:
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterPreparing Your Network C-3August 2004You must have an Ethernet adapter, the TCP/IP protocol, and Client for Microsoft Networks.If you need to install a new adapter, follow these steps:a. Click the Add button.b. Select Adapter, and then click Add.c. Select the manufacturer and model of your Ethernet adapter, and then click OK.If you need TCP/IP:a. Click the Add button.b. Select Protocol, and then click Add.c. Select Microsoft.d. Select TCP/IP, and then click OK.Note: It is not necessary to remove any other network components shown in the Network window in order to install the adapter, TCP/IP, or Client for Microsoft Networks.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterC-4 Preparing Your NetworkAugust 2004If you need Client for Microsoft Networks:a. Click the Add button.b. Select Client, and then click Add.c. Select Microsoft.d. Select Client for Microsoft Networks, and then click OK.3. Restart your PC for the changes to take effect.Enabling DHCP to Automatically Configure TCP/IP Settings in Windows 95B, 98, and Me After the TCP/IP protocol components are installed, each PC must be assigned specific information about itself and resources that are available on its network. The simplest way to configure this information is to allow the PC to obtain the information from a DHCP server in the network. You will find there are many similarities in the procedures for different Windows systems when using DHCP to configure TCP/IP.The following steps will walk you through the configuration process for each of these versions of Windows.Locate your Network Neighborhood icon.• If the Network Neighborhood icon is on the Windows desktop, position your mouse pointer over it and right-click your mouse button.• If the icon is not on the desktop,• Click Start on the task bar located at the bottom left of the window.• Choose Settings, and then Control Panel. • Locate the Network Neighborhood icon and click on it. This will open the Network panel as shown below.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterPreparing Your Network C-5August 2004Verify the following settings as shown: • Client for Microsoft Network exists• Ethernet adapter is present• TCP/IP is present•Primary Network Logon is set to Windows logonClick on the Properties button. The following TCP/IP Properties window will display.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterC-6 Preparing Your NetworkAugust 2004Selecting the Windows’ Internet Access Method1. On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.2. Double-click the Internet Options icon.3. Select “I want to set up my Internet connection manually” or “I want to connect through a Local Area Network” and click Next.4. Select “I want to connect through a Local Area Network” and click Next.5. Uncheck all boxes in the LAN Internet Configuration screen and click Next.6. Proceed to the end of the Wizard.Verifying TCP/IP PropertiesAfter your PC is configured and has rebooted, you can check the TCP/IP configuration using the utility winipcfg.exe:1. On the Windows taskbar, click the Start button, and then click Run.• By default, the IP Address tab is open on this window.• Verify the following:Obtain an IP address automatically is selected. If not selected, click in the radio button to the left of it to select it. This setting is required to enable the DHCP server to automatically assign an IP address. • Click OK to continue.Restart the PC.Repeat these steps for each PC with this version of Windows on your network.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterPreparing Your Network C-7August 20042. Type winipcfg, and then click OK.The IP Configuration window opens, which lists (among other things), your IP address, subnet mask, and default gateway.3. From the drop-down box, select your Ethernet adapter.The window is updated to show your settings, which should match the values below if you are using the default TCP/IP settings that NETGEAR recommends for connecting through a router or gateway:• The IP address is between 192.168.0.2 and 192.168.0.254• The subnet mask is 255.255.255.0• The default gateway is 192.168.0.1Configuring Windows NT4, 2000 or XP for IP NetworkingAs part of the PC preparation process, you may need to install and configure TCP/IP on each networked PC. Before starting, locate your Windows CD; you may need to insert it during the TCP/IP installation process.Installing or Verifying Windows Networking ComponentsTo install or verify the necessary components for IP networking:1. On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.2. Double-click the Network and Dialup Connections icon.3. If an Ethernet adapter is present in your PC, you should see an entry for Local Area Connection. Double-click that entry.4. Select Properties.5. Verify that ‘Client for Microsoft Networks’ and ‘Internet Protocol (TCP/IP)’ are present. If not, select Install and add them.6. Select ‘Internet Protocol (TCP/IP)’, click Properties, and verify that “Obtain an IP address automatically is selected.7. Click OK and close all Network and Dialup Connections windows.8. Then, restart your PC.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterC-8 Preparing Your NetworkAugust 2004DHCP Configuration of TCP/IP in Windows XP, 2000, or NT4You will find there are many similarities in the procedures for different Windows systems when using DHCP to configure TCP/IP.The following steps will walk you through the configuration process for each of these versions of Windows.DHCP Configuration of TCP/IP in Windows XP Locate your Network Neighborhood icon.• Select Control Panel from the Windows XP new Start Menu.• Select the Network Connections icon on the Control Panel. This will take you to the next step. • Now the Network Connection window displays.The Connections List that shows all the network connections set up on the PC, located to the right of the window.• Right-click on the Connection you will use and choose Status.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterPreparing Your Network C-9August 2004• Now you should be at the Local Area Network Connection Status window. This box displays the connection status, duration, speed, and activity statistics.• Administrator logon access rights are needed to use this window.• Click the Properties button to view details about the connection.• The TCP/IP details are presented on the Support tab page.• Select Internet Protocol, and click Properties to view the configuration information.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterC-10 Preparing Your NetworkAugust 2004DHCP Configuration of TCP/IP in Windows 2000 Once again, after you have installed the network card, TCP/IP for Windows 2000 is configured. TCP/IP should be added by default and set to DHCP without your having to configure it. However, if there are problems, follow these steps to configure TCP/IP with DHCP for Windows 2000.• Verify that the Obtain an IP address automatically radio button is selected.• Verify that Obtain DNS server address automatically radio button is selected.• Click the OK button.This completes the DHCP configuration of TCP/IP in Windows XP.Repeat these steps for each PC with this version of Windows on your network.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterPreparing Your Network C-11August 2004• Click on the My Network Places icon on the Windows desktop. This will bring up a window called Network and Dial-up Connections.• Right click on Local Area Connection and select Properties. •The Local Area Connection Properties dialog box appears. • Verify that you have the correct Ethernet card selected in the Connect using: box.• Verify that at least the following two items are displayed and selected in the box of “Components checked are used by this connection:”• Client for Microsoft Networks and• Internet Protocol (TCP/IP)• Click OK.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterC-12 Preparing Your NetworkAugust 2004• With Internet Protocol (TCP/IP) selected, click on Properties to open the Internet Protocol (TCP/IP) Properties dialogue box.• Verify that •Obtain an IP address automatically is selected.•Obtain DNS server address automatically is selected.• Click OK to return to Local Area Connection Properties.• Click OK again to complete the configuration process for Windows 2000.Restart the PC.Repeat these steps for each PC with this version of Windows on your network.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterPreparing Your Network C-13August 2004DHCP Configuration of TCP/IP in Windows NT4Once you have installed the network card, you need to configure the TCP/IP environment for Windows NT 4.0. Follow this procedure to configure TCP/IP with DHCP in Windows NT 4.0.• Choose Settings from the Start Menu, and then select Control Panel. This will display Control Panel window. • Double-click the Network icon in the Control Panel window. The Network panel will display.• Select the Protocols tab to continue.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterC-14 Preparing Your NetworkAugust 2004• Highlight the TCP/IP Protocol in the Network Protocols box, and click on the Properties button.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterPreparing Your Network C-15August 2004Verifying TCP/IP Properties for Windows XP, 2000, and NT4To check your PC’s TCP/IP configuration:1. On the Windows taskbar, click the Start button, and then click Run.The Run window opens.2. Type cmd and then click OK.A command window opens3. Type ipconfig /all Your IP Configuration information will be listed, and should match the values below if you are using the default TCP/IP settings that NETGEAR recommends for connecting through a router or gateway:• The IP address is between 192.168.0.2 and 192.168.0.254• The subnet mask is 255.255.255.0•The TCP/IP Properties dialog box now displays.• Click the IP Address tab.• Select the radio button marked Obtain an IP address from a DHCP server.• Click OK. This completes the configuration of TCP/IP in Windows NT.Restart the PC.Repeat these steps for each PC with this version of Windows on your network.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterC-16 Preparing Your NetworkAugust 2004• The default gateway is 192.168.0.14. Type exit Configuring the Macintosh for TCP/IP NetworkingBeginning with Macintosh Operating System 7, TCP/IP is already installed on the Macintosh. On each networked Macintosh, you need to configure TCP/IP to use DHCP.MacOS 8.6 or 9.x1. From the Apple menu, select Control Panels, then TCP/IP.The TCP/IP Control Panel opens:2. From the “Connect via” box, select your Macintosh’s Ethernet interface.3. From the “Configure” box, select Using DHCP Server.You can leave the DHCP Client ID box empty.4. Close the TCP/IP Control Panel.5. Repeat this for each Macintosh on your network.MacOS X1. From the Apple menu, choose System Preferences, then Network.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterPreparing Your Network C-17August 20042. If not already selected, select Built-in Ethernet in the Configure list.3. If not already selected, Select Using DHCP in the TCP/IP tab.4. Click Save.Verifying TCP/IP Properties for Macintosh ComputersAfter your Macintosh is configured and has rebooted, you can check the TCP/IP configuration by returning to the TCP/IP Control Panel. From the Apple menu, select Control Panels, then TCP/IP.The panel is updated to show your settings, which should match the values below if you are using the default TCP/IP settings that NETGEAR recommends:• The IP Address is between 192.168.0.2 and 192.168.0.254• The Subnet mask is 255.255.255.0• The Router address is 192.168.0.1If you do not see these values, you may need to restart your Macintosh or you may need to switch the “Configure” setting to a different option, then back again to “Using DHCP Server”.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterC-18 Preparing Your NetworkAugust 2004Verifying the Readiness of Your Internet AccountFor broadband access to the Internet, you need to contract with an Internet service provider (ISP) for a single-user Internet access account using a cable modem or DSL modem. This modem must be a separate physical box (not a card) and must provide an Ethernet port intended for connection to a Network Interface Card (NIC) in a computer. Your router does not support a USB-connected broadband modem.For a single-user Internet account, your ISP supplies TCP/IP configuration information for one computer. With a typical account, much of the configuration information is dynamically assigned when your PC is first booted up while connected to the ISP, and you will not need to know that dynamic information. In order to share the Internet connection among several computers, your router takes the place of the single PC, and you need to configure it with the TCP/IP information that the single PC would normally use. When the router’s Internet port is connected to the broadband modem, the router appears to be a single PC to the ISP. The router then allows the PCs on the local network to masquerade as the single PC to access the Internet through the broadband modem. The method used by the router to accomplish this is called Network Address Translation (NAT) or IP masquerading.Are Login Protocols Used?Some ISPs require a special login protocol, in which you must enter a login name and password in order to access the Internet. If you normally log in to your Internet account by running a program such as WinPOET or EnterNet, then your account uses PPP over Ethernet (PPPoE). When you configure your router, you need to enter your login name and password in the router’s configuration menus. After your network and router are configured, the router will perform the login task when needed, and you will no longer need to run the login program from your PC. It is not necessary to uninstall the login program.What Is Your Configuration Information?More and more, ISPs are dynamically assigning configuration information. However, if your ISP does not dynamically assign configuration information but instead used fixed configurations, your ISP should have given you the following basic information for your account:
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterPreparing Your Network C-19August 2004• An IP address and subnet mask• A gateway IP address, which is the address of the ISP’s router• One or more domain name server (DNS) IP addresses• Host name and domain suffixFor example, your account’s full server names may look like this:mail.xxx.yyy.com In this example, the domain suffix is xxx.yyy.com.If any of these items are dynamically supplied by the ISP, your router automatically acquires them.If an ISP technician configured your PC during the installation of the broadband modem, or if you configured it using instructions provided by your ISP, you need to copy the configuration information from your PC’s Network TCP/IP Properties window or Macintosh TCP/IP Control Panel before reconfiguring your PC for use with the router. These procedures are described next.Obtaining ISP Configuration Information for Windows ComputersAs mentioned above, you may need to collect configuration information from your PC so that you can use this information when you configure the DG834GT Super Wireless ADSL Router. Following this procedure is only necessary when your ISP does not dynamically supply the account information. To get the information you need to configure the router for Internet access:1. On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.2. Double-click the Network icon.The Network window opens, which displays a list of installed components.3. Select TCP/IP, and then click Properties.The TCP/IP Properties dialog box opens.4. Select the IP Address tab.If an IP address and subnet mask are shown, write down the information. If an address is present, your account uses a fixed (static) IP address. If no address is present, your account uses a dynamically-assigned IP address. Click “Obtain an IP address automatically”.5. Select the Gateway tab.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterC-20 Preparing Your NetworkAugust 2004If an IP address appears under Installed Gateways, write down the address. This is the ISP’s gateway address. Select the address and then click Remove to remove the gateway address.6. Select the DNS Configuration tab.If any DNS server addresses are shown, write down the addresses. If any information appears in the Host or Domain information box, write it down. Click Disable DNS.7. Click OK to save your changes and close the TCP/IP Properties dialog box.You are returned to the Network window.8. Click OK.9. Reboot your PC at the prompt. You may also be prompted to insert your Windows CD.Obtaining ISP Configuration Information for Macintosh ComputersAs mentioned above, you may need to collect configuration information from your Macintosh so that you can use this information when you configure the DG834GT Super Wireless ADSL Router. Following this procedure is only necessary when your ISP does not dynamically supply the account information. To get the information you need to configure the router for Internet access:1. From the Apple menu, select Control Panels, then TCP/IP.The TCP/IP Control Panel opens, which displays a list of configuration settings. If the “Configure” setting is “Using DHCP Server”, your account uses a dynamically-assigned IP address. In this case, close the Control Panel and skip the rest of this section.2. If an IP address and subnet mask are shown, write down the information. 3. If an IP address appears under Router address, write down the address. This is the ISP’s gateway address.4. If any Name Server addresses are shown, write down the addresses. These are your ISP’s DNS addresses.5. If any information appears in the Search domains information box, write it down.6. Change the “Configure” setting to “Using DHCP Server”.7. Close the TCP/IP Control Panel.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterPreparing Your Network C-21August 2004Restarting the NetworkOnce you have set up your computers to work with the router, you must reset the network for the devices to be able to communicate correctly. Restart any computer that is connected to the firewall.After configuring all of your computers for TCP/IP networking and restarting them, and connecting them to the local network of your DG834GT Super Wireless ADSL Router, you are ready to access and configure the router.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterC-22 Preparing Your NetworkAugust 2004
Wireless Networking Basics D-1August 2004Appendix DWireless Networking BasicsThis chapter provides an overview of Wireless networking.Wireless Networking OverviewThe DG834GT Super Wireless ADSL Router conforms to the Institute of Electrical and Electronics Engineers (IEEE) 802.11b and 802.11g standards for wireless LANs (WLANs). On an 802.11b or g wireless link, data is encoded using direct-sequence spread-spectrum (DSSS) technology and is transmitted in the unlicensed radio spectrum at 2.5 GHz. The maximum data rate for the 802.11b wireless link is 11 Mbps, but it will automatically back down from 11 Mbps to 5.5, 2, and 1 Mbps when the radio signal is weak or when interference is detected. The 802.11g auto rate sensing rates are 1, 2, 5.5, 6, 9, 12, 18, 24, 36, 48, and 54 Mbps. The 802.11 standard is also called Wireless Ethernet or Wi-Fi by the Wireless Ethernet Compatibility Alliance (WECA, see http://www.wi-fi.net), an industry standard group promoting interoperability among 802.11 devices. The 802.11 standard offers two methods for configuring a wireless network - ad hoc and infrastructure.Infrastructure ModeWith a wireless Access Point, you can operate the wireless LAN in the infrastructure mode. This mode provides wireless connectivity to multiple wireless network devices within a fixed range or area of coverage, interacting with wireless nodes via an antenna. In the infrastructure mode, the wireless access point converts airwave data into wired Ethernet data, acting as a bridge between the wired LAN and wireless clients. Connecting multiple Access Points via a wired Ethernet backbone can further extend the wireless network coverage. As a mobile computing device moves out of the range of one access point, it moves into the range of another. As a result, wireless clients can freely roam from one Access Point domain to another and still maintain seamless network connection.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterD-2 Wireless Networking BasicsAugust 2004Ad Hoc Mode (Peer-to-Peer Workgroup)In an ad hoc network, computers are brought together as needed; thus, there is no structure or fixed points to the network - each node can generally communicate with any other node. There is no Access Point involved in this configuration. This mode enables you to quickly set up a small wireless workgroup and allows workgroup members to exchange data or share printers as supported by Microsoft networking in the various Windows operating systems. Some vendors also refer to ad hoc networking as peer-to-peer group networking.In this configuration, network packets are directly sent and received by the intended transmitting and receiving stations. As long as the stations are within range of one another, this is the easiest and least expensive way to set up a wireless network. Network Name: Extended Service Set Identification (ESSID)The Extended Service Set Identification (ESSID) is one of two types of Service Set Identification (SSID). In an ad hoc wireless network with no access points, the Basic Service Set Identification (BSSID) is used. In an infrastructure wireless network that includes an access point, the ESSID is used, but may still be referred to as SSID.An SSID is a thirty-two character (maximum) alphanumeric key identifying the name of the wireless local area network. Some vendors refer to the SSID as network name. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID.The ESSID is usually broadcast in the air from an access point. The wireless station sometimes can be configured with the ESSID ANY. This means the wireless station will try to associate with whichever access point has the stronger radio frequency (RF) signal, providing that both the access point and wireless station use Open System authentication.Authentication and WEP Data EncryptionThe absence of a physical connection between nodes makes the wireless links vulnerable to eavesdropping and information theft. To provide a certain level of security, the IEEE 802.11 standard has defined these two types of authentication methods:•Open System. With Open System authentication, a wireless computer can join any network and receive any messages that are not encrypted.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterWireless Networking Basics D-3August 2004•Shared Key. With Shared Key authentication, only those PCs that possess the correct authentication key can join the network. By default, IEEE 802.11 wireless devices operate in an Open System network. Wired Equivalent Privacy (WEP) data encryption is used when the wireless devices are configured to operate in Shared Key authentication mode. 802.11 AuthenticationThe 802.11 standard defines several services that govern how two 802.11 devices communicate. The following events must occur before an 802.11 Station can communicate with an Ethernet network through an access point, such as the one built in to the DG834GT:1. Turn on the wireless station.2. The station listens for messages from any access points that are in range.3. The station finds a message from an access point that has a matching SSID.4. The station sends an authentication request to the access point.5. The access point authenticates the station.6. The station sends an association request to the access point.7. The access point associates with the station.8. The station can now communicate with the Ethernet network through the access point.An access point must authenticate a station before the station can associate with the access point or communicate with the network. The IEEE 802.11 standard defines two types of authentication: Open System and Shared Key.• Open System Authentication allows any device to join the network, assuming that the device SSID matches the access point SSID. Alternatively, the device can use the “ANY” SSID option to associate with any available Access Point within range, regardless of its SSID. • Shared Key Authentication requires that the station and the access point have the same WEP Key to authenticate. These two authentication procedures are described below.Open System AuthenticationThe following steps occur when two devices use Open System Authentication:1. The station sends an authentication request to the access point.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterD-4 Wireless Networking BasicsAugust 20042. The access point authenticates the station.3. The station associates with the access point and joins the network.This process is illustrated below.Figure D-1: Open system authenticationShared Key AuthenticationThe following steps occur when two devices use Shared Key Authentication:1. The station sends an authentication request to the access point.2. The access point sends challenge text to the station.3. The station uses its configured 64-bit or 128-bit default key to encrypt the challenge text, and sends the encrypted text to the access point.4. The access point decrypts the encrypted text using its configured WEP Key that corresponds to the station’s default key. The access point compares the decrypted text with the original challenge text. If the decrypted text matches the original challenge text, then the access point and the station share the same WEP Key and the access point authenticates the station. 5. The station connects to the network.If the decrypted text does not match the original challenge text (the access point and station do not share the same WEP Key), then the access point will refuse to authenticate the station and the station will be unable to communicate with either the 802.11 network or Ethernet network.This process is illustrated below.INTERNET LOCALACT12345678LNKLNK/ACT100Cable/DSL ProSafeWirelessVPN Security FirewallMODEL FVM318PWR TESTWLANEnableAccess Point1) Authentication request sent to AP2) AP authenticates3) Client connects to network802.11b AuthenticationOpen System StepsClientattemptingto connectRouter
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterWireless Networking Basics D-5August 2004Figure D-2: Shared key authenticationOverview of WEP ParametersBefore enabling WEP on an 802.11 network, you must first consider what type of encryption you require and the key size you want to use. Typically, there are three WEP Encryption options available for 802.11 products:1. Do Not Use WEP: The 802.11 network does not encrypt data. For authentication purposes, the network uses Open System Authentication.2. Use WEP for Encryption: A transmitting 802.11 device encrypts the data portion of every packet it sends using a configured WEP Key. The receiving device decrypts the data using the same WEP Key. For authentication purposes, the network uses Open System Authentication.3. Use WEP for Authentication and Encryption: A transmitting 802.11 device encrypts the data portion of every packet it sends using a configured WEP Key. The receiving device decrypts the data using the same WEP Key. For authentication purposes, the wireless network uses Shared Key Authentication.Note: Some 802.11 access points also support Use WEP for Authentication Only (Shared Key Authentication without data encryption). INTERNET LOCALACT12345678LNKLNK/ACT100Cable/DSL ProSafeWirelessVPN Security FirewallMODEL FVM318PWR TESTWLANEnableAccess Point1) Authenticationrequest sent to AP2) AP sends challenge text3) Client encryptschallenge text andsends it back to AP4) AP decrypts, and if correct,authenticates client5) Client connects to network802.11b AuthenticationShared Key StepsClientattemptingto connectRouter
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterD-6 Wireless Networking BasicsAugust 2004Key SizeThe IEEE 802.11 standard supports two types of WEP encryption: 40-bit and 128-bit.The 64-bit WEP data encryption method allows for a five-character (40-bit) input. Additionally, 24 factory-set bits are added to the forty-bit input to generate a 64-bit encryption key. The 24 factory-set bits are not user-configurable). This encryption key will be used to encrypt/decrypt all data transmitted via the wireless interface. Some vendors refer to the 64-bit WEP data encryption as 40-bit WEP data encryption since the user-configurable portion of the encryption key is 40 bits wide.The 128-bit WEP data encryption method consists of 104 user-configurable bits. Similar to the forty-bit WEP data encryption method, the remaining 24 bits are factory set and not user configurable. Some vendors allow passphrases to be entered instead of the cryptic hexadecimal characters to ease encryption key entry.128-bit encryption is stronger than 40-bit encryption, but 128-bit encryption may not be available outside of the United States due to U.S. export regulations. When configured for 40-bit encryption, 802.11 products typically support up to four WEP Keys. Each 40-bit WEP Key is expressed as 5 sets of two hexadecimal digits (0-9 and A-F). For example, “12 34 56 78 90” is a 40-bit WEP Key.When configured for 128-bit encryption, 802.11 products typically support four WEP Keys but some manufacturers support only one 128-bit key. The 128-bit WEP Key is expressed as 13 sets of two hexadecimal digits (0-9 and A-F). For example, “12 34 56 78 90 AB CD EF 12 34 56 78 90” is a 128-bit WEP Key.Table D-1: Encryption Key SizesNote: Typically, 802.11 access points can store up to four 128-bit WEP Keys but some 802.11 client adapters can only store one. Therefore, make sure that your 802.11 access and client adapters’ configurations match.Encryption Key Size # of Hexadecimal Digits Example of Hexadecimal Key Content64-bit (24+40) 10 4C72F08AE1128-bit (24+104) 26 4C72F08AE19D57A3FF6B260037
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterWireless Networking Basics D-7August 2004WEP Configuration OptionsThe WEP settings must match on all 802.11 devices that are within the same wireless network as identified by the SSID. In general, if your mobile clients will roam between access points, then all of the 802.11 access points and all of the 802.11 client adapters on the network must have the same WEP settings. Note: Whatever keys you enter for an AP, you must also enter the same keys for the client adapter in the same order. In other words, WEP key 1 on the AP must match WEP key 1 on the client adapter, WEP key 2 on the AP must match WEP key 2 on the client adapter, and so on.Note: The AP and the client adapters can have different default WEP Keys as long as the keys are in the same order. In other words, the AP can use WEP key 2 as its default key to transmit while a client adapter can use WEP key 3 as its default key to transmit. The two devices will communicate as long as the AP’s WEP key 2 is the same as the client’s WEP key 2 and the AP’s WEP key 3 is the same as the client’s WEP key 3.Wireless ChannelsThe wireless frequencies used by 802.11b/g networks are discussed below.IEEE 802.11b/g wireless nodes communicate with each other using radio frequency signals in the ISM (Industrial, Scientific, and Medical) band between 2.4 GHz and 2.5 GHz. Neighboring channels are 5 MHz apart. However, due to spread spectrum effect of the signals, a node sending signals using a particular channel will utilize frequency spectrum 12.5 MHz above and below the center channel frequency. As a result, two separate wireless networks using neighboring channels (for example, channel 1 and channel 2) in the same general vicinity will interfere with each other. Applying two channels that allow the maximum channel separation will decrease the amount of channel cross-talk, and provide a noticeable performance increase over networks with minimal channel separation.The radio frequency channels used in 802.11b/g networks are listed in Table D-2:
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterD-8 Wireless Networking BasicsAugust 2004Note: The available channels supported by the wireless products in various countries are different. For example, Channels 1 to 11 are supported in the U.S. and Canada, and Channels 1 to 13 are supported in Europe and Australia.The preferred channel separation between the channels in neighboring wireless networks is 25 MHz (5 channels). This means that you can apply up to three different channels within your wireless network. There are only 11 usable wireless channels in the United States. It is recommended that you start using channel 1 and grow to use channel 6, and 11 when necessary, as these three channels do not overlap.WPA Wireless SecurityWi-Fi Protected Access (WPA) is a specification of standards-based, interoperable security enhancements that increase the level of data protection and access control for existing and future wireless LAN systems. Table D-2: 802.11b/g Radio Frequency ChannelsChannel Center Frequency Frequency Spread1 2412 MHz 2399.5 MHz - 2424.5 MHz2 2417 MHz 2404.5 MHz - 2429.5 MHz3 2422 MHz 2409.5 MHz - 2434.5 MHz4 2427 MHz 2414.5 MHz - 2439.5 MHz5 2432 MHz 2419.5 MHz - 2444.5 MHz6 2437 MHz 2424.5 MHz - 2449.5 MHz7 2442 MHz 2429.5 MHz - 2454.5 MHz8 2447 MHz 2434.5 MHz - 2459.5 MHz9 2452 MHz 2439.5 MHz - 2464.5 MHz10 2457 MHz 2444.5 MHz - 2469.5 MHz11 2462 MHz 2449.5 MHz - 2474.5 MHz12 2467 MHz 2454.5 MHz - 2479.5 MHz13 2472 MHz 2459.5 MHz - 2484.5 MHz
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterWireless Networking Basics D-9August 2004The IEEE introduced the WEP as an optional security measure to secure 802.11b (Wi-Fi) WLANs, but inherent weaknesses in the standard soon became obvious. In response to this situation, the Wi-Fi Alliance announced a new security architecture in October 2002 that remedies the shortcomings of WEP. This standard, formerly known as Safe Secure Network (SSN), is designed to work with existing 802.11 products and offers forward compatibility with 802.11i, the new wireless security architecture being defined in the IEEE. WPA offers the following benefits: • Enhanced data privacy• Robust key management• Data origin authentication• Data integrity protection The Wi-Fi Alliance is now performing interoperability certification testing on Wi-Fi Protected Access products. Starting August of 2003, all new Wi-Fi certified products will have to support WPA. NETGEAR will implement WPA on client and access point products and make this available in the second half of 2003. Existing Wi-Fi certified products will have one year to add WPA support or they will lose their Wi-Fi certification. The 802.11i standard is currently in draft form, with ratification due at the end of 2003. While the new IEEE 802.11i standard is being ratified, wireless vendors have agreed on WPA as an interoperable interim standard. How Does WPA Compare to WEP?WEP is a data encryption method and is not intended as a user authentication mechanism. WPA user authentication is implemented using 802.1x and the Extensible Authentication Protocol (EAP). Support for 802.1x authentication is required in WPA. In the 802.11 standard, 802.1x authentication was optional. For details on EAP specifically, refer to IETF's RFC 2284. With 802.11 WEP, all access points and client wireless adapters on a particular wireless LAN must use the same encryption key. A major problem with the 802.11 standard is that the keys are cumbersome to change. If you do not update the WEP keys often, an unauthorized person with a sniffing tool can monitor your network for less than a day and decode the encrypted messages. Products based on the 802.11 standard alone offer system administrators no effective method to update the keys.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterD-10 Wireless Networking BasicsAugust 2004For 802.11, WEP encryption is optional. For WPA, encryption using Temporal Key Integrity Protocol (TKIP) is required. TKIP replaces WEP with a new encryption algorithm that is stronger than the WEP algorithm, but that uses the calculation facilities present on existing wireless devices to perform encryption operations. TKIP provides important data encryption enhancements including a per-packet key mixing function, a message integrity check (MIC) named Michael, an extended initialization vector (IV) with sequencing rules, and a re-keying mechanism. Through these enhancements, TKIP addresses all of known WEP vulnerabilities. How Does WPA Compare to IEEE 802.11i? WPA will be forward compatible with the IEEE 802.11i security specification currently under development. WPA is a subset of the current 802.11i draft and uses certain pieces of the 802.11i draft that are ready to bring to market today, such as 802.1x and TKIP. The main pieces of the 802.11i draft that are not included in WPA are secure IBSS (Ad-Hoc mode), secure fast handoff (for specialized 802.11 VoIP phones), as well as enhanced encryption protocols, such as AES-CCMP. These features are either not yet ready for market or will require hardware upgrades to implement. What are the Key Features of WPA Security?The following security features are included in the WPA standard: • WPA Authentication• WPA Encryption Key Management– Temporal Key Integrity Protocol (TKIP)– Michael message integrity code (MIC)– AES Support (to be phased in)• Support for a Mixture of WPA and WEP Wireless Clients, but mixing WEP and WPA is discouragedThese features are discussed below.WPA addresses most of the known WEP vulnerabilities and is primarily intended for wireless infrastructure networks as found in the enterprise. This infrastructure includes stations, access points, and authentication servers (typically RADIUS servers). The RADIUS server holds (or has access to) user credentials (for example, user names and passwords) and authenticates wireless users before they gain access to the network.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterWireless Networking Basics D-11August 2004The strength of WPA comes from an integrated sequence of operations that encompass 802.1X/EAP authentication and sophisticated key management and encryption techniques. Its major operations include:• Network security capability determination. This occurs at the 802.11 level and is communicated through WPA information elements in Beacon, Probe Response, and (Re) Association Requests. Information in these elements includes the authentication method (802.1X or Pre-shared key) and the preferred cipher suite (WEP, TKIP, or AES).The primary information conveyed in the Beacon frames is the authentication method and the cipher suite. Possible authentication methods include 802.1X and Pre-shared key. Pre-shared key is an authentication method that uses a statically configured pass phrase on both the stations and the access point. This obviates the need for an authentication server, which in many home and small office environments will not be available nor desirable. Possible cipher suites include: WEP, TKIP, and AES (Advanced Encryption Standard). We talk more about TKIP and AES when addressing data privacy below.• Authentication. EAP over 802.1X is used for authentication. Mutual authentication is gained by choosing an EAP type supporting this feature and is required by WPA. 802.1X port access control prevents full access to the network until authentication completes. 802.1X EAPOL-Key packets are used by WPA to distribute per-session keys to those stations successfully authenticated.The supplicant in the station uses the authentication and cipher suite information contained in the information elements to decide which authentication method and cipher suite to use. For example, if the access point is using the pre-shared key method then the supplicant need not authenticate using full-blown 802.1X. Rather, the supplicant must simply prove to the access point that it is in possession of the pre-shared key. If the supplicant detects that the service set does not contain a WPA information element then it knows it must use pre-WPA 802.1X authentication and key management in order to access the network.• Key management. WPA features a robust key generation/management system that integrates the authentication and data privacy functions. Keys are generated after successful authentication and through a subsequent 4-way handshake between the station and Access Point (AP).• Data Privacy (Encryption). Temporal Key Integrity Protocol (TKIP) is used to wrap WEP in sophisticated cryptographic and security techniques to overcome most of its weaknesses.• Data integrity. TKIP includes a message integrity code (MIC) at the end of each plaintext message to ensure messages are not being spoofed.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterD-12 Wireless Networking BasicsAugust 2004WPA Authentication: Enterprise-level User Authentication via 802.1x/EAP and RADIUSFigure D-3: WPA OverviewIEEE 802.1x offers an effective framework for authenticating and controlling user traffic to a protected network, as well as providing a vehicle for dynamically varying data encryption keys via EAP from a RADIUS server, for example. This framework enables using a central authentication server, which employs mutual authentication so that a rogue wireless user does not join the network. It is important to note that 802.1x does not provide the actual authentication mechanisms. When using 802.1x, the EAP type, such as Transport Layer Security (EAP-TLS), or EAP Tunneled Transport Layer Security (EAP-TTLS), defines how the authentication takes place. Note: For environments with a Remote Authentication Dial-In User Service (RADIUS) infrastructure, WPA supports Extensible Authentication Protocol (EAP). For environments without a RADIUS infrastructure, WPA supports the use of a pre-shared key.Together, these technologies provide a framework for strong user authentication. Windows XP implements 802.1x natively, and several NETGEAR switch and wireless access point products support 802.1x. Certificate Authority (for example Win Server,VeriSign)WPA enabled wireless client with “supplicant”TCP/IPPorts ClosedUntil RADIUS ServerWired Network with Optional 802.1x Port Based Network Access ControlWPA enabledAccess Point usingpre-shared key or 802.1xTCP/IPPorts OpenedAfter AuthenticatedWireless LAN LoginAuthentication
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterWireless Networking Basics D-13August 2004Figure D-4: 802.1x Authentication SequenceThe AP sends Beacon Frames with WPA information element to the stations in the service set. Information elements include the required authentication method (802.1x or Pre-shared key) and the preferred cipher suite (WEP, TKIP, or AES). Probe Responses (AP to station) and Association Requests (station to AP) also contain WPA information elements.1. Initial 802.1x communications begin with an unauthenticated supplicant (client device) attempting to connect with an authenticator (802.11 access point). The client sends an EAP-start message. This begins a series of message exchanges to authenticate the client. 2. The access point replies with an EAP-request identity message. 1234567Client with a WPA- enabled wireless adapter and supplicant (Win XP, Funk, Meetinghouse) For example, a WPA-enabled AP For example, a RADIUS server
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterD-14 Wireless Networking BasicsAugust 20043. The client sends an EAP-response packet containing the identity to the authentication server. The access point responds by enabling a port for passing only EAP packets from the client to an authentication server located on the wired side of the access point. The access point blocks all other traffic, such as HTTP, DHCP, and POP3 packets, until the access point can verify the client's identity using an authentication server (for example, RADIUS). 4. The authentication server uses a specific authentication algorithm to verify the client's identity. This could be through the use of digital certificates or some other EAP authentication type. 5. The authentication server will either send an accept or reject message to the access point. 6. The access point sends an EAP-success packet (or reject packet) to the client. 7. If the authentication server accepts the client, then the access point will transition the client's port to an authorized state and forward additional traffic. The important part to know at this point is that the software supporting the specific EAP type resides on the authentication server and within the operating system or application “supplicant” software on the client devices. The access point acts as a “pass through” for 802.1x messages, which means that you can specify any EAP type without needing to upgrade an 802.1x-compliant access point. As a result, you can update the EAP authentication type to such devices as token cards (Smart Cards), Kerberos, one-time passwords, certificates, and public key authentication, or as newer types become available and your requirements for security change. WPA Data Encryption Key ManagementWith 802.1x, the rekeying of unicast encryption keys is optional. Additionally, 802.11 and 802.1x provide no mechanism to change the global encryption key used for multicast and broadcast traffic. With WPA, rekeying of both unicast and global encryption keys is required. For the unicast encryption key, the Temporal Key Integrity Protocol (TKIP) changes the key for every frame, and the change is synchronized between the wireless client and the wireless access point (AP). For the global encryption key, WPA includes a facility (the Information Element) for the wireless AP to advertise the changed key to the connected wireless clients.If configured to implement dynamic key exchange, the 802.1x authentication server can return session keys to the access point along with the accept message. The access point uses the session keys to build, sign and encrypt an EAP key message that is sent to the client immediately after sending the success message. The client can then use contents of the key message to define applicable encryption keys. In typical 802.1x implementations, the client can automatically change encryption keys as often as necessary to minimize the possibility of eavesdroppers having enough time to crack the key in current use.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterWireless Networking Basics D-15August 2004Temporal Key Integrity Protocol (TKIP)WPA uses TKIP to provide important data encryption enhancements including a per-packet key mixing function, a message integrity check (MIC) named Michael, an extended initialization vector (IV) with sequencing rules, and a re-keying mechanism. TKIP also provides for the following: • The verification of the security configuration after the encryption keys are determined. • The synchronized changing of the unicast encryption key for each frame. • The determination of a unique starting unicast encryption key for each preshared key authentication.MichaelWith 802.11 and WEP, data integrity is provided by a 32-bit integrity check value (ICV) that is appended to the 802.11 payload and encrypted with WEP. Although the ICV is encrypted, you can use cryptanalysis to change bits in the encrypted payload and update the encrypted ICV without being detected by the receiver.With WPA, a method known as Michael specifies a new algorithm that calculates an 8-byte message integrity check (MIC) using the calculation facilities available on existing wireless devices. The MIC is placed between the data portion of the IEEE 802.11 frame and the 4-byte ICV. The MIC field is encrypted together with the frame data and the ICV.Michael also provides replay protection. A new frame counter in the IEEE 802.11 frame is used to prevent replay attacks.Optional AES Support to be Phased InOne of the encryption methods supported by WPA, besides TKIP, is the advanced encryption standard (AES), although AES support will not be required initially for Wi-Fi certification. This is viewed as the optimal choice for security conscience organizations, but the problem with AES is that it requires a fundamental redesign of the NIC’s hardware in both the station and the access point. TKIP is a pragmatic compromise that allows organizations to deploy better security while AES capable equipment is being designed, manufactured, and incrementally deployed.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterD-16 Wireless Networking BasicsAugust 2004Is WPA Perfect?WPA is not without its vulnerabilities. Specifically, it is susceptible to denial of service (DoS) attacks. If the access point receives two data packets that fail the message integrity code (MIC) within 60 seconds of each other, then the network is under an active attack, and as a result, the access point employs counter measures, which include disassociating each station using the access point. This prevents an attacker from gleaning information about the encryption key and alerts administrators, but it also causes users to lose network connectivity for 60 seconds. More than anything else, this may just prove that no single security tactic is completely invulnerable. WPA is a definite step forward in WLAN security over WEP and has to be thought of as a single part of an end-to-end network security strategy.Product Support for WPAStarting in August, 2003, NETGEAR, Inc. wireless Wi-Fi certified products will support the WPA standard. NETGEAR, Inc. wireless products that had their Wi-Fi certification approved before August, 2003 will have one year to add WPA so as to maintain their Wi-Fi certification.WPA requires software changes to the following: • Wireless access points • Wireless network adapters • Wireless client programsSupporting a Mixture of WPA and WEP Wireless Clients is DiscouragedTo support the gradual transition of WEP-based wireless networks to WPA, a wireless AP can support both WEP and WPA clients at the same time. During the association, the wireless AP determines which clients use WEP and which clients use WPA. The disadvantage to supporting a mixture of WEP and WPA clients is that the global encryption key is not dynamic. This is because WEP-based clients cannot support it. All other benefits to the WPA clients, such as integrity, are maintained.However, a mixed mode supporting WPA and non-WPA clients would offer network security that is no better than that obtained with a non-WPA network, and thus this mode of operation is discouraged.Changes to Wireless Access PointsWireless access points must have their firmware updated to support the following:
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterWireless Networking Basics D-17August 2004•The new WPA information element To advertise their support of WPA, wireless APs send the beacon frame with a new 802.11 WPA information element that contains the wireless AP's security configuration (encryption algorithms and wireless security configuration information). •The WPA two-phase authentication Open system, then 802.1x (EAP with RADIUS or preshared key). •TKIP •Michael •AES (optional)To upgrade your wireless access points to support WPA, obtain a WPA firmware update from your wireless AP vendor and upload it to your wireless AP.Changes to Wireless Network AdaptersWireless networking software in the adapter, and possibly in the OS or client application, must be updated to support the following: •The new WPA information element Wireless clients must be able to process the WPA information element and respond with a specific security configuration. •The WPA two-phase authentication Open system, then 802.1x supplicant (EAP or preshared key). •TKIP •Michael •AES (optional)To upgrade your wireless network adapters to support WPA, obtain a WPA update from your wireless network adapter vendor and update the wireless network adapter driver.For Windows wireless clients, you must obtain an updated network adapter driver that supports WPA. For wireless network adapter drivers that are compatible with Windows XP (Service Pack 1) and Windows Server 2003, the updated network adapter driver must be able to pass the adapter's WPA capabilities and security configuration to the Wireless Zero Configuration service. Microsoft has worked with many wireless vendors to embed the WPA firmware update in the wireless adapter driver. So, to update your Microsoft Windows wireless client, all you have to do is obtain the new WPA-compatible driver and install the driver. The firmware is automatically updated when the wireless network adapter driver is loaded in Windows.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterD-18 Wireless Networking BasicsAugust 2004Changes to Wireless Client ProgramsWireless client programs must be updated to permit the configuration of WPA authentication (and preshared key) and the new WPA encryption algorithms (TKIP and the optional AES component).To obtain the Microsoft WPA client program, visit the Microsoft Web site.
Glossary -1August 2004Glossary10BASE-T IEEE 802.3 specification for 10 Mbps Ethernet over twisted pair wiring.100BASE-Tx IEEE 802.3 specification for 100 Mbps Ethernet over twisted pair wiring.802.11b IEEE specification for wireless networking at 11 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.5GHz.802.11g IEEE specification for wireless networking at 54 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.5GHz.802.11x 802.1x defines port-based, network access control used to provide authenticated network access and automated data encryption key management. The IEEE 802.1x draft standard offers an effective framework for authenticating and controlling user traffic to a protected network, as well as dynamically varying encryption keys. 802.1x uses a protocol called EAP (Extensible Authentication Protocol) and supports multiple authentication methods, such as token cards, Kerberos, one-time passwords, certificates, and public key authentication. For details on EAP specifically, refer to IETF's RFC 2284.Access Control List (ACL) An ACL is a database that an Operating System uses to track each user’s access rights to system objects (such as file directories and/or files).Ad-hoc Mode An 802.11 networking framework in which devices or stations communicate directly with each other, without the use of an access point (AP). Ad-hoc mode is also referred to as peer-to-peer mode or an Independent Basic Service Set (IBSS). Ad-hoc mode is useful for establishing a network where wireless infrastructure does not exist or where services are not required.ADSL See Asymmetric Digital Subscriber LineAsymmetric Digital Subscriber Line A technology for sending data over regular telephone lines. ADSL allows data rates up to 8 Mbps downstream and 640 Kbps upstream.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router-2 GlossaryAugust 2004Cat 5 Category 5 unshielded twisted pair (UTP) cabling. An Ethernet network operating at 10 Mbits/second (10BASE-T) will often tolerate low quality cables, but at 100 Mbits/second (10BASE-Tx) the cable must be rated as Category 5, or Cat 5 or Cat V, by the Electronic Industry Association (EIA). This rating will be printed on the cable jacket. Cat 5 cable contains eight conductors, arranged in four twisted pairs, and terminated with an RJ45 type connector. In addition, there are restrictions on maximum cable length for both 10 and 100 Mbits/second networks.Denial of Service attack DoS. A hacker attack designed to prevent your computer or network from operating or communicating.DHCP See Dynamic Host Configuration Protocol.DMZ Specifying a Default DMZ Server allows you to set up a computer or server that is available to anyone on the Internet for services that you have not defined. There are security issues with doing this, so only do this if you are willing to risk open accessDNS See Domain Name Server.Domain Name A descriptive name for an address or group of addresses on the Internet. Domain names are of the form of a registered entity name plus one of a number of predefined top level suffixes such as.com, .edu, .uk, and so on. For example, in the address mail.NETGEAR.com, mail is a server name and NETGEAR.com is the domain.Domain Name Server A Domain Name Server (DNS) resolves descriptive names of network resources (such as www.NETGEAR.com) to numeric IP addresses.DSLAM DSL Access Multiplexor. The piece of equipment at the telephone company central office that provides the ADSL signal.Dynamic Host Configuration ProtocolDHCP. An Ethernet protocol specifying how a centralized DHCP server can assign network configuration information to multiple DHCP clients. The assigned information includes IP addresses, DNS addresses, and gateway (router) addresses.Gateway A local device, usually a router, that connects hosts on a local network to other networks.IP See Internet Protocol.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterGlossary -3August 2004IP Address A four-byte number uniquely defining each host on the Internet. Ranges of addresses are assigned by Internic, an organization formed for this purpose. Usually written in dotted-decimal notation with periods separating the bytes (for example, 134.177.244.57).IPSec Internet Protocol Security. IPSec is a series of guidelines for securing private information transmitted over public networks. IPSec is a VPN method providing a higher level of security than PPTP.ISP Internet service provider.Internet Protocol The main internetworking protocol used in the Internet. Used in conjunction with the Transfer Control Protocol (TCP) to form TCP/IP.LAN See local area network.local area network LAN. A communications network serving users within a limited area, such as one floor of a building. A LAN typically connects multiple personal computers and shared network devices such as storage and printers. Although many technologies exist to implement a LAN, Ethernet is the most common for connecting personal computers.MAC address Media Access Control address. A unique 48-bit hardware address assigned to every Ethernet node. Usually written in the form 01:23:45:67:89:ab.Mbps Megabits per second.MDI/MDIX In cable wiring, the concept of transmit and receive are from the perspective of the computer, which is wired as a Media Dependant Interface (MDI). In MDI wiring, a computer transmits on pins 1 and 2. At the hub, switch, router, or access point, the perspective is reversed, and the hub receives on pins 1 and 2. This wiring is referred to as Media Dependant Interface - Crossover (MDI-X).MSB See Most Significant Bit or Most Significant Byte.MTU See Maximum Transmission Unit.Maximum TransmitUnitThe size in bytes of the largest packet that can be sent or received.Most Significant Bit or Most Significant Byte The portion of a number, address, or field that is farthest left when written as a single number in conventional hexadecimal ordinary notation. The part of the number having the most value.NAT See Network Address Translation.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router-4 GlossaryAugust 2004Netmask A number that explains which part of an IP address comprises the network address and which part is the host address on that network. It can be expressed in dotted-decimal notation or as a number appended to the IP address. For example, a 28-bit mask starting from the MSB can be shown as 255.255.255.192 or as /28 appended to the IP address.Network Address Translation A technique by which several hosts share a single IP address for access to the Internet.packet A block of information sent over a network. A packet typically contains a source and destination network address, some protocol and length information, a block of data, and a checksum.PPP See Point-to-Point Protocol.PPPoA See PPP over ATMPPPoE See PPP over EthernetPPP over ATM PPPoA. PPP over ATM is a protocol for connecting remote hosts to the Internet over an always-on connection by simulating a dial-up connection.PPP over Ethernet PPPoE. PPP over Ethernet is a protocol for connecting remote hosts to the Internet over an always-on connection by simulating a dial-up connection.PPTP Point-to-Point Tunneling Protocol. A method for establishing a virtual private network (VPN) by embedding Microsoft’s network protocol into Internet packets.PSTN Public Switched Telephone Network.Point-to-Point Protocol PPP. A protocol allowing a computer using TCP/IP to connect directly to the Internet.RADIUS Short for Remote Authentication Dial-In User Service, RADIUS is an authentication system. Using RADIUS, you must enter your user name and password before gaining access to a network. This information is passed to a RADIUS server, which checks that the information is correct, and then authorizes access. Though not an official standard, the RADIUS specification is maintained by a working group of the IETF. RFC Request For Comment. Refers to documents published by the Internet Engineering Task Force (IETF) proposing standard protocols and procedures for the Internet. RFCs can be found at www.ietf.org.RIP See Routing Information Protocol.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL RouterGlossary -5August 2004router A device that forwards data between networks. An IP router forwards data based on IP source and destination addresses.Routing Information Protocol A protocol in which routers periodically exchange information with one another so that they can determine minimum distance paths between sources and destinations.SSID A Service Set Identification is a thirty-two character (maximum) alphanumeric key identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless computer card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name. See also Wireless Network Name and ESSIDsubnet mask See netmask.Universal Plug and Play UPnP. A networking architecture that provides compatibility among networking technology. UPnP compliant routers provide broadband users at home and small businesses with a seamless way to participate in online games, video conferencing and other peer-to-peer services.UTP Unshielded twisted pair. The cable used by 10BASE-T and 100BASE-Tx Ethernet networks.VCI Virtual Channel Identifier. Together with the VPI, defines a Virtual Channel through an ATM network. Used by ATM switching equipment to route data through the network.VPI Virtual Path Identifier. Together with the VCI, defines a Virtual Channel through an ATM network. Used by ATM switching equipment to route data through the network.WAN See wide area network.WEP Wired Equivalent Privacy. WEP is a data encryption protocol for 802.11b wireless networks. All wireless nodes and access points on the network are configured with a 64-bit or 128-bit Shared Key for data encryption.wide area network WAN. A long distance link used to extend or connect remotely located local area networks. The Internet is a large WAN.Wi-Fi See 802.11b. A trade name for the 802.11b wireless networking standard, given by the Wireless Ethernet Compatibility Alliance (WECA, see http://www.wi-fi.net), an industry standard group promoting interoperability among 802.11b devices.
Reference Manual for the Model DG834GT 108 Mbps Super Wireless ADSL Router-6 GlossaryAugust 2004Windows Internet Naming Service WINS. Windows Internet Naming Service is a server process for resolving Windows-based computer names to IP addresses. If a remote network contains a WINS server, your Windows PCs can gather information from that WINS server about its local hosts. This allows your PCs to browse that remote network using Network Neighborhood.WINS See Windows Internet Naming Service.WPA Wi-Fi Protected Access (WPA) is a specification of standards-based, interoperable security enhancements that increase the level of data protection and access control for existing and future wireless LAN systems.

Navigation menu