Nextivity orporated CELFI-RS240CU Cel-Fi Residential System User Manual 420N003 001 001 10R51

Download:
Mirror Download [FCC.gov]
Document ID	1573905
Application ID	GMWKUAJMkSLfkFhrff4f8Q==
Document Description	420N003-001-001-10R51
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	114.96kB (1436957 bits)
Date Submitted	2011-11-03 00:00:00
Date Available	2012-02-02 00:00:00
Creation Date	2011-05-12 12:10:44
Producing Software	Adobe PDF Library 7.0
Document Lastmod	2011-05-23 16:25:15
Document Title	420N003-001-001-10R51
Document Creator	Adobe InDesign CS2 (4.0.5)

COVER AGE
UNIT
WINDOW
UNIT
WINDOW
UNIT
Step 1
Step 2
Find the spot with the best 3G coverage:
The first step in setting up your Cel-Fi system is to
find the spot in your home or office that has the best
3G coverage. This is typically by a window, and if you
are in a multi-story building, upstairs windows are
usually better than downstairs windows.
Plug in the Window Unit:
Take the Window Unit and one power supply out of
the box (both power supplies are the same, so grab
either one). Plug the Window Unit in, and check to
make sure that you can see at least 1 “Bar” on the
display in the center of the device. If you do not see
at least 1 bar, try a different location.
Congratulations on your new
indoor signal solution.
This Cel-Fi system is designed to provide you with significant
improvements in coverage as well as 3G data rates.
Setting up the system is extremely simple and
consists of placing and plugging in two components;
a Window Unit and a Coverage Unit.
By spending just a few minutes using the instructions in this
guide, you can optimize the installation and get the very most
from your new Cel-Fi System.
If you have any trouble during setup, please use the trouble
shooting steps included in this guide.
CEL-FIRS2
Quick Start Guide
NEED HELP?
Visit us at
www.celfihelp.com
for an installation video and
other helpful information
regarding installation and
trouble shooting.
In the package you will find:
Window Unit
Coverage Unit
Two power adapters.
Place the Coverage Unit
Move to a location in your home where you need to
have improved coverage. Plug the Coverage unit in and
wait until the numeric display stops cycling,
this could take several minutes.
At this point you should see a green icon
indicating that the unit is working properly.
It is possible to place the Coverage Unit so
far away that it cannot communicate with
COVER AGE
the Window Unit. If this happens, a red icon
UNIT
will illuminate indicating that you need to
move the Coverage Unit closer to the Window unit.
Optimize the Window Unit Placement
The number of bars you can see on the Window
Unit make a significant difference in the operation of
the Cel-Fi system. Try moving the Window Unit to a
couple of different spots to see if you can get better
signal; the more bars the better.
Step 4
Step 3
WINDOW
UNIT
TOO CLOSE
A zero on the numeric
display indicates that
the “Coverage Unit”
needs to be moved
farther away from the
“Window Unit”.
GOOD
This green icon
indicates that the
“Coverage Unit” is
functioning normally.
TOO FAR
This red icon indicates
that the “Coverage
Unit” needs to be
moved closer to the
“Window Unit”.
Step 5
Optimize The Coverage Unit Placement
The farther away you place the coverage unit from the Window unit the better the coverage in
your home, so put the Coverage Unit as far away from the Window Unit as possible.
The number shown on the side of the display gives you an indication as to the quality of the
placement. Test two or three locations and for best results; try and get a 7, 8 or 9 on the display.
CEL-FIRS2 Trouble Shooting
WINDOW
UNIT
COV ER AGE
UNIT
ERRO R
ME SSAGES
1. Try resetting the ”Coverage Unit” by unplugging it and then plugging it back in.
2. If problem persists return system for service.
Hardware Error.
Red Status Indicator.
1. Move the ”Coverage Unit” closer to the “Window Unit”.
The ”Coverage Unit” is “Too Far”
from the “Window Unit”
Red “Too Far” Indicator.
1. Move the ”Coverage Unit” further away from the “Window Unit”.
The ”Coverage Unit” is “Too Close”
to the “Window Unit”.
7 segment display shows a value of 0.
1. Wait for the display to stop cycling, this could take several minutes
2. Move away from WiFi devices.
The ”Coverage Unit” is taking
longer than normal to make a link.
7 segment display is cycling for more
than a minute.
There is no power.
No lights on ”Coverage Unit” display.
Problem
Indicator
Not receiving cell signal.
No segment lit on signal display and
status indicator on solid green.
Hardware Error.
Status indicator is on solid red.
Error Code on ”Coverage Unit”.
Status indicator is flashing red.
The “Window Unit” unit is attempting
to complete regulatory compliance.
Status indicator is flashing green for
more than a minute.
There is no power.
No lights on “Window Unit” display.
Problem
Indicator
Indicator
Problem
Try This
1. Is the unit plugged in?
2. Is there power at the outlet?
3. Try exchanging the power supplies with the “Coverage Unit” to see if the
power supply is defective.
1. Wait for the status indicator to stop flashing, this could take several minutes.
1. See the “Coverage Unit” to determine what error code is being displayed.
1. Try resetting the “Window Unit” by unplugging it and then plugging it back in.
2. If problem persists return system for service/replacement.
1. Try moving the “Window Unit” to another room or area where you have more
coverage. (Use your cell phone to find the best 3G coverage).
Try This
1. Is the unit plugged in?
2. Is there power at the outlet?
3. Try exchanging the power supplies with the “Window Unit” to see if the
power supply is defective.
Try This
Make sure that the vents on the unit are not blocked. Move the unit to a cooler area.
The system will start working normally when it cools down.
“Window Unit” is overheating.
E4
”Coverage Unit” is overheating.
E3
Try moving the “Window Unit” to another room or area where you have coverage.
(Use your cell phone to find the best 3G coverage).
No Signal on “Window Unit”.
E1
420N003-001-001-10R51

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Tagged PDF                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:39
Instance ID                     : uuid:5686c68c-670e-429e-98ad-ad46db10176e
Document ID                     : adobe:docid:indd:210f0f42-7e1a-11e0-9125-84539b2561ae
Rendition Class                 : proof:pdf
Derived From Instance ID        : 210f0f41-7e1a-11e0-9125-84539b2561ae
Derived From Document ID        : adobe:docid:indd:210f0f40-7e1a-11e0-9125-84539b2561ae
Manifest Link Form              : ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 320.00, 72.00
Manifest Placed Y Resolution    : 320.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches
Manifest Reference Instance ID  : uuid:288448CE62A511E0ACFB8F40DAFFA501, uuid:62ef064a-4ffe-11e0-b884-001b63a3b8f1
Manifest Reference Document ID  : uuid:288448CD62A511E0ACFB8F40DAFFA501, uuid:BDCB23E84E4611E0AE46897078553144
Create Date                     : 2011:05:12 12:10:44-07:00
Modify Date                     : 2011:05:23 16:25:15-07:00
Metadata Date                   : 2011:05:23 16:25:15-07:00
Creator Tool                    : Adobe InDesign CS2 (4.0.5)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 7696 bytes, use -b option to extract)
Format                          : application/pdf
Producer                        : Adobe PDF Library 7.0
Trapped                         : False
Has XFA                         : No
Page Count                      : 2
Container Version               : 9
Creator Version                 : 11
Creator                         : Adobe Illustrator(R) 11.0
For                             : Mickey S,
Title                           : 420N003-001-001-10R51.pdf
Bounding Box                    : 0 0 792 1224
Image Height                    : 1224
Image Width                     : 792
Image Size                      : 792x1224
Megapixels                      : 0.969

EXIF Metadata provided by EXIF.tools