Nextivity orporated CELFI-RSCU104 Cel-Fi Residential System User Manual Basic CMYK

Download:
Mirror Download [FCC.gov]
Document ID	1285265
Application ID	zbM1xQnvKjUetT0nNTP21w==
Document Description	420N001-001-10R51 small
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	17.44kB (217940 bits)
Date Submitted	2010-05-24 00:00:00
Date Available	2010-09-20 00:00:00
Creation Date	2010-05-20 13:41:16
Producing Software	Acrobat Distiller 8.2.2 (Windows)
Document Lastmod	2010-05-20 13:41:16
Document Title	Basic CMYK
Document Creator	Adobe Illustrator CS2
Document Author:	DBare

Trouble Shooting Guide
The Cel-Fi Window and Coverage Units have Power and Status
indicator lights to help you determine how the Units are operating and
how to obtain the best coverage within your home.
Indicator
Problem
Try this:
Power off
(no green light)
There is no power
to the Unit.
1. Is the Unit plugged in?
2. Is there power to the outlet?
3. Try exchanging power supplies with the other unit
to see if the power supply is defective.
Status red
There is a problem
with Cel-Fi.
1. Unplug the unit, wait a few minutes, and try again.
2. Visit the installation support section at:
www.celfihelp.com for more information.
Status flashing red
The Unit has switched
to a low power mode
because the environment is too warm.
1. Do not cover the Unit or block the vents.
2. Move the Unit to a cooler spot.
3. The unit will start operating again when it cools.
The Unit is taking
longer than normal to
make a link.
1. Wait longer. System is verifying regulatory
compliance. This could take up to 30 minutes.
2. Make sure Units are not next to a Wi-Fi router.
Window Unit
No green bars
1. Try moving the Window Unit to another room
where you have better mobile phone coverage.
(Use your mobile phone to find the best location.)
Coverage Unit
The Coverage Unit is
too far away from the
Window Unit.
1. Move the Coverage Unit closer to
the Window Unit.
The Coverage Unit
is too close to the
Window Unit
1. Move the Coverage Unit farther
away from the Window Unit.
Common Indicators
Signal
indicators
Status
Power
(((
)))
Status flashing green
for more than a minute
(((
Error Messages
)))
If there is a system fault, the Coverage Unit will display an error message on the display in the location where
the coverage number is usually displayed (see below).
COVERAGE NUMBER
If this occurs the message will alternate between displaying an “E” (for error) and then a number.
The table below shows what values will be displayed and what they mean.
PATENT 7,519,323
“E1”
Window Unit cannot find the network
Make sure you have one bar coverage on Window Unit.
“E2”
Window Unit has interference
Make a test call. If you can’t, move the Window Unit.
“E3 or E4”
Environment is too warm for Unit
System will operate again when it cools.
420N001-001-10R51
2 Step
Quick Start Guide
The Cel-Fi Window Unit takes the strongest cell signal in your home
and distributes it throughout via the Coverage Unit
Mobile signal
before installation
Mobile signal
after installation
FOOT,
WALL MOUNT
AND POWER
ADAPTERS
WINDOW
UNIT
PRESS THE
WINDOW UNIT
ONTO THE FOOT
NEED HELP?
Visit www.celfihelp.com for an installation video and other helpful
information regarding the installation and trouble shooting of your system
COVERAGE
UNIT
Step2: Setup the Coverage Unit
Step1: Setup the Window Unit
Signal
indicator
Status
Power
COVERAGE UNIT
Location
indicators
WINDOW
UNIT
Set Coverage Unit near the middle of your
home and plug it into the nearest outlet.
Wait until the status light stops flashing.
You should see this on the Coverage
Unit indicator panel.
WINDOW UNIT
Status
Power
COVERAGE
UNIT
Locate the best 3G signal within your
home and plug the Window Unit into
the nearest power outlet. (Look for
the 3G icon on your mobile phone).
Placing the Window Unit near a window is best.
SIGNAL
BAR INDICATOR
Located in the middle
of the Window Unit.
Note:
If you do not see at least one bar
in the signal indicator window
(as on left), move the unit closer
to a window or try another room.
Upstairs is best if available.
COVERAGE UNIT INDICATOR PANEL
If the indicator looks like this,
move the Coverage Unit
away from the Window Unit.
If the indicator looks like this,
move the Coverage Unit
closer to the Window Unit.
The larger this number,
the better your coverage.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:39
Format                          : application/pdf
Title                           : Basic CMYK
Creator                         : DBare
Creator Tool                    : Adobe Illustrator CS2
Create Date                     : 2010:05:20 13:41:16-07:00
Modify Date                     : 2010:05:20 13:41:16-07:00
Metadata Date                   : 2009:05:22 16:35:37-07:00
Thumbnail Width                 : 256
Thumbnail Height                : 152
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 18423 bytes, use -b option to extract)
Document ID                     : uuid:959E7683456311DEA5DBCB063BD9FBE5
Instance ID                     : uuid:a0d288e4-7239-461c-a271-d1e2ff6eb156
Derived From Instance ID        : uuid:959E7682456311DEA5DBCB063BD9FBE5
Derived From Document ID        : uuid:9ECF704F454811DEA5DBCB063BD9FBE5
Startup Profile                 : Basic CMYK
Producer                        : Acrobat Distiller 8.2.2 (Windows)
Page Count                      : 2
Author                          : DBare

EXIF Metadata provided by EXIF.tools