Nextivity orporated Q34-45121325CU Provider-Specific Consumer Signal Booster User Manual

Nextivity Incorporated Provider-Specific Consumer Signal Booster

User Manual

Download: Nextivity orporated Q34-45121325CU Provider-Specific Consumer Signal Booster User Manual
Mirror Download [FCC.gov]Nextivity orporated Q34-45121325CU Provider-Specific Consumer Signal Booster User Manual
Document ID3648271
Application IDXhzaBB3FQP69chC2e4h84A==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeYes
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize108.7kB (1358781 bits)
Date Submitted2017-11-22 00:00:00
Date Available2018-05-18 00:00:00
Creation Date2017-03-30 12:08:00
Producing SoftwareAdobe PDF Library 15.0
Document Lastmod2017-11-07 10:39:27
Document TitleUser Manual
Document CreatorAdobe InDesign CC 2015 (Macintosh)

PRODUCT INFORMATION
Cel-Fi™ QUATRA Smart Cellular Coverage
STOP!!! Do not call your service provider
until you have read the Quick Start Guide.
If you need help, visit: www.cel-fi.com/support.
Safety Precautions
• Use Cel-Fi indoors. It should not be
used outdoors.
• These products are designed to be
used with a direct plug-in power supply
unit that shipped with the Network Unit.
When installing the equipment, all the
requirements of the manufacturer and
the referenced standards must be met.
• There are no user serviceable parts
inside.
• CAUTION: Changes or modifications to
this product not expressly approved by
Nextivity may void your right to operate
the equipment.
Warranty
Nextivity Inc provides a limited warranty for its
products. For details, please refer to http://cel-fi.
com/warranty.
Limitation of Liability
In no event shall Nextivity, nor its directors,
employees, agents, suppliers or End Users,
be liable under contract, tort, strict liability,
negligence or any other legal or equitable theory
with respect to the Products or any other subject
matter of this Agreement (i) for any lost profits,
cost of procurement of substitute goods or
services, or special, indirect, incidental, punitive, or
consequential damages of any kind whatsoever
or (ii) for any direct damages in excess of (in the
aggregate) the fees actually received by Nextivity
from End User with respect to the Products
actually purchased and paid for.
See cel-fi.com for list of patents covering this
product.
Trademark
Cel-Fi, IntelliBoost, and Nextivity
trademarks of Nextivity, Inc.
This is a CONSUMER device.
logo
are
BEFORE USE, you MUST REGISTER THIS DEVICE
with your wireless provider and have your provider’s
consent. Most wireless providers consent to the
use of signal boosters. Some providers may not
consent to the use of this device on their network.
If you are unsure, contact your provider.
You MUST operate this device with approved
antennas and cables as specified by the
manufacturer.
Antennas MUST be installed at least 20 cm (8
inches) from any person.
You MUST cease operating this device
immediately if requested by the FCC, Innovation,
Science and Economic Development Canada or a
licensed wireless service provider.
WARNING. E911 location information may not be
provided or may be inaccurate for calls served by
using this device.
FCC Statement (Applicable in the USA only)
When used with any mobile device utilizing the
1710-1755 MHz band, the FCC limits booster
equipment placement to a maximum of 10
meters above ground level. Installation of this
equipment which does not comply with federal
requirements may subject the owner to FCC
enforcement action.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential
PRODUCT INFORMATION
Cel-Fi™ QUATRA Smart Cellular Coverage
STOP!!! Do not call your service provider
until you have read the Quick Start Guide.
If you need help, visit: www.cel-fi.com/support.
Safety Precautions
• Use Cel-Fi indoors. It should not be
used outdoors.
• These products are designed to be
used with a direct plug-in power supply
unit that shipped with the Network Unit.
When installing the equipment, all the
requirements of the manufacturer and
the referenced standards must be met.
• There are no user serviceable parts
inside.
• CAUTION: Changes or modifications to
this product not expressly approved by
Nextivity may void your right to operate
the equipment.
Warranty
Nextivity Inc provides a limited warranty for its
products. For details, please refer to http://cel-fi.
com/warranty.
Limitation of Liability
In no event shall Nextivity, nor its directors,
employees, agents, suppliers or End Users,
be liable under contract, tort, strict liability,
negligence or any other legal or equitable theory
with respect to the Products or any other subject
matter of this Agreement (i) for any lost profits,
cost of procurement of substitute goods or
services, or special, indirect, incidental, punitive, or
consequential damages of any kind whatsoever
or (ii) for any direct damages in excess of (in the
aggregate) the fees actually received by Nextivity
from End User with respect to the Products
actually purchased and paid for.
See cel-fi.com for list of patents covering this
product.
Trademark
Cel-Fi, IntelliBoost, and Nextivity
trademarks of Nextivity, Inc.
This is a CONSUMER device.
logo
are
BEFORE USE, you MUST REGISTER THIS DEVICE
with your wireless provider and have your provider’s
consent. Most wireless providers consent to the
use of signal boosters. Some providers may not
consent to the use of this device on their network.
If you are unsure, contact your provider.
You MUST operate this device with approved
antennas and cables as specified by the
manufacturer.
Antennas MUST be installed at least 20 cm (8
inches) from any person.
You MUST cease operating this device
immediately if requested by the FCC, Innovation,
Science and Economic Development Canada or a
licensed wireless service provider.
WARNING. E911 location information may not be
provided or may be inaccurate for calls served by
using this device.
FCC Statement (Applicable in the USA only)
When used with any mobile device utilizing the
1710-1755 MHz band, the FCC limits booster
equipment placement to a maximum of 10
meters above ground level. Installation of this
equipment which does not comply with federal
requirements may subject the owner to FCC
enforcement action.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and
can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which
can be determined by turning the equipment off
and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV
technician for help
ISED STATEMENT
This is a CONSUMER device.
BEFORE USE, meet all requirements set out
in CPC-2-1-05.
This device may operate in a fixed location only, for
in-building use.
In order to comply with ISED RF Exposure
requirements, this device must be installed to
provide at least 20 cm separation from the human
body at all times.
[FRENCH: Afin de se conformer aux exigences
d’exposition RF de ISED, cet appareil doit être
installé pour fournir au moins 20 cm de séparation
du corps humain en tout temps.]
The Manufacturer’s rated output power of this
equipment is for single carrier operation. For
situations when multiple carrier signals are
present, the rating would have to be reduced by
3.5 dB, especially where the output signal is reradiated and can cause interference to adjacent
band users. This power reduction is to be by
means of input power or gain reduction and not by
an attenuator at the output of the device.
son fonctionnement avec porteuse unique. Pour
des appareils avec porteuses multiples, on doit
réduire la valeur nominale de 3,5dB, surtout si le
signal de sortie est retransmis et qu’il peut causer
du brouillage aux utilisateurs de bandes adjacentes.
Une telle réduction doit porter sur la puissance
d’entrée ou sur le gain, et ne doit pas se faire au
moyen d’un atténuateur raccordé à la sortie du
dispositif.]
This device complies with Industry Canada licenseexempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may
not cause interference, and (2) this device must
accept any interference, including interference that
may cause undesired operation of the device.
[FRENCH: Le présent appareil est conforme
aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes: (1)
l’appareil ne doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.]
Gain
100dB
Bandwidth
75Mhz
Input and Output
Impedances
50 ohm
Output
Power
Uplink
22dBm per band
Downlink
16dBm per band
Compliance Contact
In the event of regulatory compliance issue, please
contact Nextivity Inc. directly. Contact information
is available at www.nextivityinc.com.
Patents
This product is covered by Nextivity, Inc., US
patents and patents pending. Please refer to
cel-fi.com for details.
Copyright
Copyright © 2017 by Nextivity, Inc. All rights
reserved. Reproduction or media conversion by
any means is protected by copyright and may only
occur with prior written permission of Nextivity.
Designed by Nextivity in California.
installation. This equipment generates, uses and
can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which
can be determined by turning the equipment off
and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV
technician for help
ISED STATEMENT
This is a CONSUMER device.
BEFORE USE, meet all requirements set out
in CPC-2-1-05.
This device may operate in a fixed location only, for
in-building use.
In order to comply with ISED RF Exposure
requirements, this device must be installed to
provide at least 20 cm separation from the human
body at all times.
[FRENCH: Afin de se conformer aux exigences
d’exposition RF de ISED, cet appareil doit être
installé pour fournir au moins 20 cm de séparation
du corps humain en tout temps.]
The Manufacturer’s rated output power of this
equipment is for single carrier operation. For
situations when multiple carrier signals are
present, the rating would have to be reduced by
3.5 dB, especially where the output signal is reradiated and can cause interference to adjacent
band users. This power reduction is to be by
means of input power or gain reduction and not by
an attenuator at the output of the device.
son fonctionnement avec porteuse unique. Pour
des appareils avec porteuses multiples, on doit
réduire la valeur nominale de 3,5dB, surtout si le
signal de sortie est retransmis et qu’il peut causer
du brouillage aux utilisateurs de bandes adjacentes.
Une telle réduction doit porter sur la puissance
d’entrée ou sur le gain, et ne doit pas se faire au
moyen d’un atténuateur raccordé à la sortie du
dispositif.]
This device complies with Industry Canada licenseexempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may
not cause interference, and (2) this device must
accept any interference, including interference that
may cause undesired operation of the device.
[FRENCH: Le présent appareil est conforme
aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes: (1)
l’appareil ne doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.]
Gain
100dB
Bandwidth
75Mhz
Input and Output
Impedances
50 ohm
Output
Power
Uplink
22dBm per band
Downlink
16dBm per band
Compliance Contact
In the event of regulatory compliance issue, please
contact Nextivity Inc. directly. Contact information
is available at www.nextivityinc.com.
Patents
This product is covered by Nextivity, Inc., US
patents and patents pending. Please refer to
cel-fi.com for details.
Copyright
Copyright © 2017 by Nextivity, Inc. All rights
reserved. Reproduction or media conversion by
any means is protected by copyright and may only
occur with prior written permission of Nextivity.
Designed by Nextivity in California.
[FRENCH: La puissance de sortie nominale
indiquée par le fabricant pour cet appareil concerne
[FRENCH: La puissance de sortie nominale
indiquée par le fabricant pour cet appareil concerne
Legal_QuatraLR-Eng-2-4-5-12-13
U.S. Headquarters: Nextivity Inc.
16550 West Bernardo Drive
Bldg. 5, Suite 550
San Diego, CA 92127, USA
+1 858.485.9442 tel
+1 858.485.9445 fax
www.cel-fi.com
Bureau in Europe
Unit 6, Basepoint Business Centre
Rivermead Drive, Westlea
Swindon SN5 7EX
Nextivity Singapore Pte. Ltd.
2 Changi Business Park Avenue 1
Level 2 – Suite 16,
486015 Singapore
Legal_QuatraLR-Eng-2-4-5-12-13
U.S. Headquarters: Nextivity Inc.
16550 West Bernardo Drive
Bldg. 5, Suite 550
San Diego, CA 92127, USA
+1 858.485.9442 tel
+1 858.485.9445 fax
www.cel-fi.com
Bureau in Europe
Unit 6, Basepoint Business Centre
Rivermead Drive, Westlea
Swindon SN5 7EX
Nextivity Singapore Pte. Ltd.
2 Changi Business Park Avenue 1
Level 2 – Suite 16,
486015 Singapore

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Create Date                     : 2017:03:30 12:08:00-07:00
Creator                         : Adobe InDesign CC 2015 (Macintosh)
Modify Date                     : 2017:11:07 10:39:27-08:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.4-c006 80.159825, 2016/09/16-03:31:08
Metadata Date                   : 2017:11:07 10:39:27-08:00
Creator Tool                    : Adobe InDesign CC 2015 (Macintosh)
Instance ID                     : uuid:af9ec1d3-45c5-4e05-83b9-358fdd946b6d
Original Document ID            : xmp.did:B626C39852206811B6A4D97738D90740
Document ID                     : xmp.id:df838184-4beb-46ea-87ef-e9c3db03044e
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:b5b03d87-edfd-4e91-b857-2e5c7e714baf
Derived From Document ID        : xmp.did:F97F117407206811871FE6BE57A2A30D
Derived From Original Document ID: xmp.did:B626C39852206811B6A4D97738D90740
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2015 (Macintosh)
History Changed                 : /
History When                    : 2017:03:30 12:08-07:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 2
EXIF Metadata provided by EXIF.tools
FCC ID Filing: YETQ34-45121325CU

Navigation menu