Nextlink RP24RA4D 2.4GHz RADIO CONTROL User Manual Manual

Nextlink Co., Ltd. 2.4GHz RADIO CONTROL Manual

Users Manual

User's ManualHandbuchRF䊝䉳䊠䊷䊦䊶䊧䉲䊷䊋䊷ขᛒ⺑᣿ᦠRF ϐʨ / Ύչд ӡٝ ԋύԅ*This user guide is subject to change without notice.RP24TD9RP24TD9JRP24TD9MRP24RA4DRP24RA5DRP24RA6DRP24RA8DRP24RA9DVer. 2.0www.rcenjoy.comTx 2.4GHz Radio Control Receiver
&OHMJTIڋڌIntroductionThe existing 2.4GHz Radio Control and receivers cause  inconvenienceto RC users because of restricted frequency use, which comes from FM radio technology.Utilizing digital spectrum technology within the 2.4 GHz ISM band, the Radiopost RF System provides secure radio link, high transmission speed and superb resolution allowing the device to respond quickly and accurately without interference. TheRadiopost  Tx 2.4GHz Radio Control and receivers offer a significant advantageof eliminating the possibility of interference. Each Tx 2.4GHz Radio Control is programmed with a unique identification codeto communicate with its specified receiver.  Once the receiver ispaired with the Tx 2.4GHz Radio Control (called ID Setting), the receiver will onlytake data from this specific radio controller where the Tx 2.4GHz Radio Controlis equipped, ignoring signals from other sources.The Radiopost Tx 2.4GHz Radio Control and receivers scan and select thesuperior channels that are not being used to avoid collision in channels and data loss between the Tx 2.4GHz Radio Control and the receiver.This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received,including interference that may cause undesired operation.FCC Information
&OHMJTIڋڍPrecautionsRead this manual before installation or use.Do not disassemble the Tx 2.4GHz Radio Control and the receiver because it may cause severe damage or problems.Install the Tx 2.4GHz Radio Control and the receiver after cutting off thepower of the radio controller and RC models such as modelaircrafts or helicopters or cars.The receiver should be turned on after the radio controller is switched on. When turning on the radio controller, be sureto put the throttle to the stop position. When switching off, make sure the engine or the motorof the RC models should be stopped. First, switch off the receiver then the radio controller. If this is not done in this order, it may cause temporary malfunctions.Prior to actual use and control of RC models, perform operation tests between the Tx 2.4GHz Radio Control and the receiver.If these tests fail, do not operate RC models.When installing the receiver in RC models, use impact protection materials to avoid damage to the receiver, which may be caused by the vibration of RC models or the impact from the outside.Do not alter length of antenna arbitrarily. The antenna should not be hidden by the RC model's main body or cover, coated with metallic paint or carbon fiber.Do not use Radiopost Tx 2.4GHz Radio Control and receivers togetherwith Tx 2.4GHz Radio Control and receivers produced by other manufacturers. Do not operate the Tx module with two or more receivers.The receiver antenna shall be installed not to get affected by the magnetic field of power cables.* Nextlink will not be responsible for damage caused by use which is prohibited.4BGFUZ$BVUJPO
&OHMJTIڋڎName of Each PartRP24TD9JRP24TD9ID SettingButtonID SettingButtonStatusLEDStatusLEDID SettingButtonStatusLEDRP24TD9MRP24RA4D RP24RA8D RP24RA9DRP24RA6DRP24RA5D[For JR radio controllers] [For Sanwa radio controllers][For Futaba and Hitec radio controllers]www.rcenjoy.comSpread Spectrum2.4GHz2.4GHzRF MODULEwww.rcenjoy.comID SET STATUSRP24TD9J2.4GHz2.4GHzRF MODULEID SETSTATUSRP24TD9RP24TD9www.rcenjoy.comAntenna AntennaAntennaStatus LEDID SettingButtonRP24RA6DRP24RA6D2.4GHz2.4GHz6CH ReceiverID SETՙ՞Շՙ՞Ոՙ՞Չՙ՞Պՙ՞Ջ՘Յՙ՞Ռwww.r cenjo y.comAntenna AntennaStatus LEDID Setting ButtonFailsafe ButtonRP24RA8DRP24RA8D2.4GHz2.4GHz8CH ReceiverID SET F/Sՙ՞Շՙ՞Ոՙ՞Չՙ՞Պՙ՞Ջՙ՞Ռՙ՞Ս՘Յՙ՞Վwww.rcenjoy.comAntennaStatus LEDID SettingButtonFailsafe ButtonStatus LEDID SettingButtonՙՇՙՈՙՉՙՊ՘ՅՙՋ55ChannelReceiverwww.rcenjoy.com2.4GHz2.4GHzRP24RA5DRP24RA5DAntennaStatus LEDID SettingButtonAntennaID SET2.4GHz2.4GHzRP24RA4DRP24RA4D44ChannelChannelTx  2.4GHz Radio ControlReceiver
&OHMJTIڋڏTxModuleFeaturesHigh stability is guaranteed by using 2.4 GHz ISM bandwidth.Crystal  is not necessary due to automatic channel selection.ID Setting is checked by beeping sounds.Binding speed is superior.The embedded Tx 2.4GHz Radio Control antenna provides convenience for users when the stand is attached to the radio controller.Radiopost Tx 2.4GHz Radio Control can be paired with any Radiopost receivers.It provides a wide range and high durability.It is a highly sensitive receiver which is less affected by intermodulationIt is a universal type which can be used for modelaircrafts, helicopters and cars.It is free from "NO CONTROL" after ID Setting.The Failsafe Function (only applied to RP24RA8D/RP24RA9D)minimizes damage to RC models caused by accident. Receiver
&OHMJTIڋڐLED Status by FunctionWhen powered on for the firsttime, the white LED blinks.When ID Setting button is pressed, the white LED blinks faster than previously.When ID Setting is done, the LED turns green and remains still.The white LED blinks slowly if there is no data transferred from theTx 2.4GHz Radio ControlLED turns greenWhite LED blinks slowlyWhite LED blinksPowerTxModuleRed LED blinksReceiverGreen LED blinks.Green color remains stillWhite LED blinks  fasterWhen powered on for the firsttime, the green LED blinks turning into the receiver searchingstatus.When ID Setting button is pressed, it turns into ID-Settingmode and the red LED blinks.When ID Setting is done, the LED turns green and the greencolor remains still.
&OHMJTIڋڑInstallation InstructionsWhite LED blinksPowerChoose a Tx 2.4GHz Radio Control which is suitable for the radio controller and connect it to the controller after checkinglocation of the connector pins. Mount the receiver on the properposition after checking the servoand the polarization of the batteries.TheTx module will beep for three times and the green LED will blink when users turn on the radio controller.Connect the power to the receiver.The white LED will begin to blink.Press the ID Setting button of the Tx module for 1 second.The red LED will start to blink. Press the ID setting button of the receiver for 1 second. The white LED will start to blink.When the ID setting is done, the LEDs of the Tx moduleand the receiver will turn green and the Tx module beepstwice.Check the movement of the servos by operating the leverof the radio controller.
&OHMJTIڋڒFailsafe FunctionThe Failsafe Function is used to redirect the servos to the designated location set by users in advance when there is a connection failure or data loss for 2 seconds duringthe flying session.Turning on the Failsafe FunctionTurn on the Tx 2.4GHz Radio Control first and then the receiver. Check the paring by moving the lever of the radio controller. By using the lever of the radio controller, set the positionsof each servo to be redirected when the Failsafe mode gets started.Press the Failsafe Function button for 3 seconds. TheLED will blink in red once, which means the Failsafe Function is activated.* When users set the Failsafe Function with the receiver   installed in the RC models, be sure to put the engine   power channel of the radio controller in hold mode or   cut off the engine power.*When you buy the Tx 2.4GHz Radio Control and receivers, the Failsafe function is not activated. If  wish to set the Failsafe function, please follow instructions described  in the user guide."QQMJFEUP.PEFM3'3"%3'3"%POMZ$BVUJPOFailsafe Function Setup
&OHMJTIڋڔWarrantyRepair ServiceIf any difficulties are encountered while setting up or operating the modules, please consult this instruction manual first. For further assistance you may also refer to your hobby dealer, or contact Radiopost Service Center at the website or call or fax us at the numbers below;Web site: www.rcenjoy.comName of ProductsDate of purchaseDealer or storeTel.CustomerWarranty period: 12 months from date of retail purchasePrice:Remarks:TxReceiverRP24TD9 / RP24TD9J / RP24TD9MRP24RA4D / RP24RA5D / RP24RA6D / RP24RA8D / RP24RA9DNameAddressTel.The damage caused by accident, abuse, misuse, flood, earthquake or other external causes.The damage caused by the service performed by anyone who is nota representative of Radiopost or a Radiopost authorized service provider.The products or parts that have been modified to alter functionality or capability without approval of Radiopost.In case the seal on the module is defected or detached.3. This warranty covers repairs of defected hardware at no charge, exchange ofit for the product which is new or equivalent to new in performance and reliability     and a refund of the purchase price.4. If there are any product defects that arise, please contact the retail store or     the contact information below.1. The warranty period for this product is 12 months from the date of retail     purchase.The warranty covers any defects in materials and workmanship     under normal use.2. Limitations: Even within the warranty period, service charges may be     required for the followings:Europe, Asia PacificTel.: +82-31-737-6060Fax: +82-31-737-6263Email: arex@nextlink.co.krNorth America, Latin AmericaTel.: +1-949-273-8282Fax: +1-949-273-8285Eamil:anthony@nextlink.co.kr
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is con-nected. • Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation including interference that may cause undesired operationIMPORTANT NOTE: FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.   SUCH MODIFICATIONS COULD VOIDTHE USER᪽S AUTHORITY TO OPERATE THE EQUIPMENT.
IMPORTANT Safety Instruction: 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions.   5) Do not use this equipment near water. 6) Do not using near any heat sources such as radiators, heat resisters, stove, or other equipment that produce heat.

Navigation menu