NiCOM USA NT150FP03 NT 150 W FM EXCITER User Manual USERS MANUAL

Download:
Mirror Download [FCC.gov]
Document ID	393032
Application ID	o1aCUXbAuG6yPfeXA0r+5Q==
Document Description	USERS MANUAL
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	17.28kB (216061 bits)
Date Submitted	2004-01-30 00:00:00
Date Available	2004-01-30 00:00:00
Creation Date	2004-01-15 12:33:53
Producing Software	Adobe Acrobat 6.0 Paper Capture
Document Lastmod	2004-01-15 12:41:27
Document Title	USERS MANUAL
Document Creator	HP PrecisionScan Pro 3.0

NT150 Technical and Maintenance Manual NicomUsa Inc
REMOTE CONTROL FEATURE
The NT 1 50 is equipped with a 9 pin RS 232 connectorthatallows all the mains telemetry
functions. The software is supplied with the unit and with this CD mm it‘s possible to monitor
and to change the main parameters ot the NT 150 on the computer's screen.
The NT 1 50 is also supplied with the interlock connectorthat allows to switch the poweron and
off simply bygrounding the innerconductorofthe BNC.
NOTE:
The CD Rom supplied contains the remote control software of the NT 150.
REMOTE CONTROL SOFTWARE
INSTALLATION
The NT 150 comes with a Serial port RS 232. This port allows a Bi-Directional remote control of
the unit from a PC.
INSTALLING THE SOFTWARE
1. Insertthe NT 150 CD-ROM into the CD drive.
2. Run Setupexe file found in the main folderof the CD-ROM. The installation will continue
automatically asking only for the name of the folder of the hard drive where the program will
be installed. It will be necessary to reboot the computer.
3. Once installed, the Tx_Nicom program icon can be recalled by clicking : Start - Programs -
Tx_Nicom ioon.
CONNECTING THE NT 150
The NT 150 is equipped with a Serial Port (R8232) in the rear panel. To connect the computer
with the NT 150 we recommend standard serial cables Pin-to-Pin; the lenght of the cable must
stay within 60 feet.
REMEMBER T0 CDOSETH'E PROGRAM BEFORE REMOVINGTHE CONNECTING CABLE
Page3
MT 150 Technical andMaintenancs Manual NicomUse Inc
RUNNING THE PROGRAM
Once the program is running, from the main screen it is necessary to click the POWER ON
button; the screen will light up and a message" COMMUNICATION IN PROGRESS"wilI appear.
After few seconds, on the left side of the screen, the operating frequency will appear together
with all the other parameters. If not, check the Communication port setting (COM1-COM 2).
To change it, click the File menu and then select "set Port”.
The otherparameters shown on the screen are the following:
lTemgerature in Celsius ( rememberthat Fameneit is Celsius x 1 .8 + 20)
2. Lock Indicator showing that PLL oi rcult of the unit is locked
34 Onthe Air showingthatthe unitistransmitting
4. RF Forward giving the amountofWatts radiated
5. RE Reflected giving the amount of reflected power
On the right side of the screen there are fourbuttons that allowto modifythe parameters:
a. Send Button to be used aftera change of frequency is made
b. Set Freguency allows the change offrequency by clicking the new frequen'cy on
the keyboard on the left side of the screen
cl Disconnect allowsto dlsconnectthe system
do RF On turns upand downthe pqwer
NT 150 Technical and Maintenance Manual NicomUsa Inc
NT 150 PROGRAMMING
Connecta 50 ohm load or 50 ohm antenna to the RF output, connect the equipment into a mains
supply (100+24O VAC). The equipment is factory pre—set to 10 W
Switch ON the power and the yellow VPOWER LED wiI/Iight‘
The Display will show:
WA'T C] PROGRAM
C] SETTiNG
Afters seconds the green PLL LOCK led will light and the Display willshowan increasing bar. After
a further 5 seconds the green ENABLE LED will light and there will be output power
At this point the Display will show the next parameter
Level Modulation (MOD >
Forward Power(FRW1 0M;
Reflected Power (RFL 0.4W)4
M01» IIIIIlu C] PR°GRAM
D SETTING
FRW 10W RFL 0.4W
The default frequency is 98.000 MHz.
To display the frequency push the SETTING key.
In order to display the parameter push the SELECT key.
Page 5
NT 7 50 TechnicalandMeintenance Manual NicomUsa Inc
Disglaz Password
The Password mode is factory set to enable, and is not possible change this setting
The default password is 1 2 3,
The way forchanglng the password is the following:
. Press the PROGRAM key for 3 seconds;
PASSWORD
9123456789
E] PROGRAM
D SETTING
. Press the PROGRA Mkey to move the underscore characterposition at the required digit, and
press the SETTING key to confirm the digit.
PASSWORD * C] PROGRAM
0123456789
[j SETTING , \
Repeat the same for the two remaining digits
PASSWORD *** ”D PR°GRAM
0123456789
C] SETTING
. If the password is correct press the SETTING key to cenfln'n, otherwise press the PROGRAM
key to select again
CONFIRM (YIN) ? C] PROGRAM
N=SEL. Y=SET.
D SETTING
Pages
NT150 Technical and Maintenance Manual NicomUsa Inc
If the password is not correct an error is displayed
E RRO R D PROGRAM
PASSWORD
D smmq
After a few seconds the display will show the parameters again.
When the password is correct, the display will show
NEW PASS. = SET. C] PROGRAM
NEW FREQ. = PRG
[j SETTING
To change the password press the SETTING key.
To change the frequency press the PROGRAM key.
CHANGE OF PASSWORD
The password is set at the factory and corresponds to the numbers 1 - 2 — 3A
However it is possible to set a new custom password,
The main purpose is to avoid somebody to enter your system and modify the
main parameters of your settings.
Every new password has to be made with only three numbers,
It is very important that you write somewhere the new password, because once that has been
set, it is not possible to change anymore or to make any change if the password is not entered.
VERY IMPORTANT:
KEEP TRACK OF YOUR NEW PASSWORD IllI
Page7
NT 1 50 Technicaland Maintenance Manual Nicornusa Inc
. For changing the password proceed with the same method for the required password:
NEW PASSWORD PROGRAM
9123456789
SETTING
CONFIRMATION PR°GRAM
9123456789 smmc.
If the password is corre- ct the display will show:
STO RE D D PROGRAM
NEW PASSWORD D SETTING
If the can flnnation password is wrong the display will show:
E RRO R D PROGRAM
CONFIRMATION D SETTING
IMPORTANT NOTE
I BE CAREFUL I
Once the passwordis set, itmustberemembered, otherwise neitherthe frequencynorthe
password can be reset and the unit has to be sent back to the factory.
Page 8
NT 150 Technical and Maintenance Manual NicomUsa Inc
Disglaz Change of quencx.
o Press the PROGRAM key fora seconds and enter the correct password. At this point press again the
SELECT key:
NEw PASS. = D PR°GRAM
NEW FREQ .
E] SETTING
- Press the PROGRAM key to change the desired digit and press the SETTING key to confirm it
FREQUENCY ? D PROGRAM
D SETTING
The underscore character indicates which digit can be change.
To move the underscore character hit the PROGRAM key.
MHz 103.900
When the new frequency is chosen, then press the SETTING key confirm it,
Aftera “WAIT CYCLE", the display will show the parameters:
MOD> l llllEl D PROGRAM
FRW 5.0W RFL 0.4W
C] SETTING
After 7 minutes the display light will switch off and the display will show:
NICOM 3 PROGRAM
MHz 103.900
[3 SETTING
Pages

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 7
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:ec074504-7ac3-474e-9dbc-877f665ab5c7
Producer                        : Adobe Acrobat 6.0 Paper Capture
Create Date                     : 2004:01:15 12:33:53-05:00
Creator Tool                    : HP PrecisionScan Pro 3.0
Modify Date                     : 2004:01:15 12:41:27-05:00
Metadata Date                   : 2004:01:15 12:41:27-05:00
Document ID                     : uuid:e0fd341b-c657-4b4d-ac97-8194c3b4976d
Format                          : application/pdf
Creator                         : HP PrecisionScan Pro 3.0

EXIF Metadata provided by EXIF.tools