Nimbus WIMI310 mini-PCIe WiFi Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3447818
Application ID	DNPSAZqzne69kpG+k0zjkA==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	20.36kB (254542 bits)
Date Submitted	2017-07-02 00:00:00
Date Available	2017-12-29 00:00:00
Creation Date	2017-06-28 16:43:52
Producing Software	Adobe PDF Library 11.0
Document Lastmod	2017-06-28 16:43:55
Document Title	Users Manual
Document Creator	Wordìš© Acrobat PDFMaker 11
Document Author:	김종호

WiMi310 User Manual v1.0
Wired/Wireless Multi-media interface
WiMi310
User Manual
Ver. 1.0
2017. 1. 16
© 2017 NIMBUS INC. All rights reserved.
1/10
www.nimbus.kr
WiMi310 User Manual v.1.0
Document Revision History
Revision
Date
Description
v1.0
January 16, 2017
Initial release of WiMi310 Product Datasheet v1.0
© 2017 NIMBUS INC. All rights reserved.
2/10
www.nimbus.kr
WiMi310 User Manual v.1.0
•
The RF module limited to OEM installation ONLY.
The OEM integrator is responsible for the compliance to all the rules that apply to the
product in to which this certified RF module is integrated.
•
This module must be integrated into a device where the user cannot access the antenna
connector and should not be able to remove or install the module.
Dipole antenna(Under 6.26 ㏈i) can be used with this module. The antenna gain must
not exceed it.
•
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received. Including interference that may cause undesired
operation.
•
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
•
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
•
FCC Caution
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment. This transmitter must
not be co-located or operating in conjunction with any other antenna or transmitter.
•
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
© 2017 NIMBUS INC. All rights reserved.
3/10
www.nimbus.kr
WiMi310 User Manual v.1.0
20cm between the radiator & your body.
•
This device is intended only for OEM integrators under the following conditions:
The antenna must be installed such that 20 cm is maintained between the antenna and
users, and The transmitter module may not be co-located with any other transmitter or
antenna. As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed.
•
IMPORTANT NOTE:
In the event that these conditions cannot be met (for example certain laptop configurations
or colocation with another transmitter), then the FCC authorization is no longer considered
valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM
integrator will be responsible for re-evaluating the end product (including the transmitter)
and obtaining a separate FCC authorization.
•
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final end
product must be labeled in a visible area with the following:
“Contains FCC ID: ZD7-WIMI310”.
The grantee's FCC ID can be used only when all FCC compliance requirements are met.
•
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding
how toinstall or remove this RF module in the user's manual of the end product which
integrates this module. The end user manual shall include all required regulatory
information/warning as show in this manual.
© 2017 NIMBUS INC. All rights reserved.
4/10
www.nimbus.kr
WiMi310 User Manual v.1.0
Purpose of this Document
This document provides simple circuit description and detailed specifications of the
WiMi310™ WiFi Module. The document is intended for Hardware designer wishing to
implementation of WiMi310 module into their own systems.
Related Documents
Additional information related to this document can be found in the Following documents
: PCB Form Factor
PCI Express
TM
Card Electromechanical Specification Revision 1.1 (March 28, 2005)
© 2017 NIMBUS INC. All rights reserved.
5/10
www.nimbus.kr
WiMi310 User Manual v.1.0
Key Features
• 2x3 MIMO antenna configuration using two spatial streams
• IEEE Std. 802.11 n Network Standards
• Modulation modes: OFDM
• WPS Certified- Wireless Protected Setup for easy set up and security configuration
• Functions as a legacy endpoint device that conforms to the PCI Express Base Specification,
Rev 1.1
• Optimal channel selection and connection management
• Seamless channel switch under interference
• Only 40 MHz channel bandwidth support.
• 300MHz PHY Rate Support and STBC Support for Extended Range
• Antenna: 3x IPex Connectors (2T/3R) - U.FL
• MAC Filtering - No Restriction Mode, White List Mode, Black List Mode; Up to 32
connections
• WDS Enables network management units to collect statistics and manage the device
remotely
• Support Low Power Mode
• RoHS Compliance
© 2017 NIMBUS INC. All rights reserved.
6/10
www.nimbus.kr
WiMi310 User Manual v.1.0
Electrical Specifications
Parameter
Symbol
Value
Min.
Supply Voltage
VDD 5.0V
Input voltage to digital pins
Vin
Storage temperature
TSTG
Typ.
-0.3
-20
Unit
Note
Max.
+6.0
+3.6
+50
℃
Table 2. Absolute Maximum Ratings
Attention : Stress above the Max. values listed here may cause permanent damage to the
device. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability. Maximum ratings are absolute ratings : exceeding only one of these value
may cause irreversible damage to the integrated circuit.
The Following Table is defined in typical conditions:Ta=25℃, unless otherwise specified.
Parameter
Symbol
Value
Unit
Min.
Typ.
Max.
5.0
5.5
Supply Voltage
VDD 5.0V
3.9
Input high voltage
VIH
2.0
5.5
Input low voltage
VIL
-0.3
0.8
Output high voltage
VOH
2.4
Output low voltage
VOL
IOZ
Tri-State
Output
leakage
Note/Test Condition
without DC load
0.4
without DC load
±10
uA
current
Pull-up resistor
Rpu
26
38
59
KΩ
Pull-down resistor
Rpd
33
47
81
KΩ
I/O pins input capacitance
CI
Total Power Consumption
pF
5.5
Table 3. DC Parameters Information
© 2017 NIMBUS INC. All rights reserved.
7/10
www.nimbus.kr
WiMi310 User Manual v.1.0
Pinout Description
PIN #
Name
Type
Description
WAKE#
In
Link reactivation
45,47,49,51
+5.0V
Power
+5.0V Power
3,5,8,10,12,14,
Reseved
Reserve
Leave unconnected
16,17,19,20,
45,47,49,51
4,9,15,18,21,
GND
Power
Ground
+1.5V (Reserved)
Reserve
Not used until now, leave unconnected.
26,27,29,34,
35,37,40,43,50
6,28,48
CLKREQ#
Out
Reference clock request
11
REFCLKn
In
Reference Clock, Differential Pair Negative
13
REFCLKp
In
Reference Clock, Differential Pair Positive
22
PERST#
In
Functional reset
23
PERn
In
PCI Express x1 data Input, negative
25
PERp
In
PCI Express x1 data Input, positive
30
SMB_CLK
In
SMBus Clock
32
SMB_DATA
In/Out
SMBus Data
31
PETn
Out
PCI Express x1 data Output, negative
33
PETp
Out
PCI Express x1 data Output, positive
36
USB_Dn
In/Out
USB Serial Data, negative
38
USB_Dp
In/Out
USB Serial Data, positive
42
LED_WWAN#
Out
Status Indication LED signal, active low
44
LED_WLAN#
Out
Status Indication LED signal, active low
46
LED_WPAN#
Out
Status Indication LED signal, active low
Table 4. Pinout Description
© 2017 NIMBUS INC. All rights reserved.
8/10
www.nimbus.kr
WiMi310 User Manual v.1.0
PCI Express Interface Description
• PCI Express Interface Unit(PCIE) functions as a PCI Express legacy endpoint device that
conforms to the PCI Express Base Specification, Rev 1.1.
• As PCIe endpoint device, it can be configured to be either a master initiating PCIe
operation or a target responding to a PCIe operation. The PCIe I/F is a 2.5GHz signaling, x1
differential link
Parameters
Description
Master transaction types
All memory transactions, except lock
Supports PCIe master DMA
IO and configuration transactions – not supported
Target transaction types
Supports two outstanding non-posted requests as a target (computer)
All memory transactions – type 0 only
Message support
Supports interrupt and error messages
Configuration space
Extended 4KB PCIe Configuration Space
Single function device
Interrupts
Support of both MSI and interrupt messages
Error reporting
Full support of PCIe baseline error reporting
Full support of advanced error reporting capability
Three error severity levels – correctable, non-fatal and fatal
Header logging and pointer to first uncorrectable error
Programmable error severity
PCI error mapping – mapping errors to PCI error reporting mechanism
Address space
Two 32-bit memory BARs
Virtual channels
Support of baseline TC0-VC0 mapping
Single VC0 HW resource
Table 5. WiMi310 PCIe Supported Features
© 2017 NIMBUS INC. All rights reserved.
9/10
www.nimbus.kr
WiMi310 User Manual v.1.0
Mechanical Description
PCB Form Factors are complied with “PCI Express Mini Card Electomechanical Specification
Rev.1.2”, (Oct 26, 2007)
• width : 30.0mm
• width : 50.95mm
• Thickness : 5.0mm
© 2017 NIMBUS INC. All rights reserved.
10/10
www.nimbus.kr

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : 김종호
Company                         : 
Create Date                     : 2017:06:28 16:43:52+09:00
Modify Date                     : 2017:06:28 16:43:55+09:00
Source Modified                 : D:20170628074330
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2017:06:28 16:43:55+09:00
Creator Tool                    :  Word용 Acrobat PDFMaker 11
Document ID                     : uuid:12dbcf8a-ad93-4596-a07e-92a0b9eb31eb
Instance ID                     : uuid:bb04e0da-06c6-4691-bc1a-23bc992fbe71
Subject                         : 33
Format                          : application/pdf
Title                           : 블럭설계서
Creator                         : 김종호
Producer                        : Adobe PDF Library 11.0
Page Layout                     : OneColumn
Page Count                      : 10

EXIF Metadata provided by EXIF.tools