Ningbo EverFlourish Smart Technology EF200T Remote control transmitter User Manual VBA EF200T

Download:
Mirror Download [FCC.gov]
Document ID	1531941
Application ID	cZrCECO91FCrWLSi/evuhA==
Document Description	VBA-EF200T_User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	1.91kB (23902 bits)
Date Submitted	2011-08-29 00:00:00
Date Available	2011-08-31 00:00:00
Creation Date	2011-08-22 13:21:08
Producing Software	Bullzip PDF Printer / www.bullzip.com / Freeware Edition (not registered)
Document Lastmod	2011-08-22 13:21:08
Document Title	VBA-EF200T_User manual
Document Creator	PScript5.dll Version 5.2.2
Document Author:	wakeyouw

Instruction Manual for
RF Remote Control Socket and Transmitter
EMW200R-UL，
，EMW200RA-UL, the remote control socket
EMW200T-1，
，EMW200TA-1, the hand held transmitter
As always follow electrical safety precautions, do not use with unattended appliances or those involving
heating elements.
Function
1. The remote control socket (EMW200R-UL，EMW200RA-UL) turns on and off the connected lighting or
appliance by a wireless transmitter (EMW200T-1，EMW200TA-1) using radio frequency up to 80ft away.
2. It is ideal for controlling lighting for the purposes of home automation and energy saving.
3. Each transmitter controls up to 3 channels. Each channel can command up to 3 receivers.
Operation
1. Check the group setting at the back of the transmitter, A, B, C or D. If the transmitter is in group A, then, the
commanded receiver has to be in the same group setting.
2. Check the group setting at the back of the receiver is same as transmitter and the channel no, eg. A1, A2 or A3
3. Connect the remote control socket to the mains power supply.
4. Press the corresponding “ON”, “OFF” buttons on the transmitter to switch on and off the connected appliance by
remote control. (eg. on/off buttons 1 controls receiver A1, 2 controls receiver A2, 3 controls A3)
5. The indicator on the receiver blink once for every reception of power on/off
Caution
1. For safety reason, always switch off your appliance before connection.
2. Appliances to be connected to the remote control socket MUST NOT exceed the voltage and frequency ratings
as in “Specifications”.
3. User can adjust the channel group on the transmitter and socket receiver at any time. And to change the group
setting, eg. From A1 to A2, or to A3, in order to change the control button position on the transmitter.
4. To adjust the channel or the groups, always use a big screw driver with the same diameter as the adjustment
arrow at the back of the socket and receiver. A small screw driver will deform the plastic housing during
adjustment.
Specifications
EMW200R-UL，
，EMW200RA-UL
1. Power Rating : 125V~, 8A, resistive, 625W tungsten
2. Frequency: : 433.92 MHz,
3. Distance:
: 80ft max. (open area)
EMW200T，
，EMW200TA
1. Battery
: 23A 3L R50 12V
2. Frequency
: 433.92 MHz
3. Distance
: 80ft max. (open area)
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé
pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de
brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type
d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication
satisfaisante.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 2
Producer                        : Bullzip PDF Printer / www.bullzip.com / Freeware Edition (not registered)
Create Date                     : 2011:08:22 13:21:08
Modify Date                     : 2011:08:22 13:21:08
Author                          : wakeyouw
Title                           : 
Creator                         : PScript5.dll Version 5.2.2

EXIF Metadata provided by EXIF.tools