Ningbo EverFlourish Smart Technology EF203T Remote control transmitter User Manual EMW200R UL EMW203T E
Everflourish Electrical Co., Ltd. Remote control transmitter EMW200R UL EMW203T E
VBA-EF203T_User manual
EMW200R-UL+EMW203T (E).doc, P1/2
Instruction Manual for
RF Remote Socket and Transmitter
Ref: EMW200R-UL + EMW203T
Function
1. The remote control socket turns on and off the appliance by a wireless transmitter using radio frequency up to
25 meters away.
2. It is ideal for controlling appliance for the purposes of home automation and energy saving.
3. Each transmitter controls up to 3 channels. Each channel can command up to 3 receivers.
Operation
1. Check the group setting at the back of the transmitter, A, B, C or D. If the transmitter is in group A, then, the
commanded receiver has to be in the same group setting.
2. Check the group setting at the back of the receiver is same as transmitter and the channel no, eg. A1, A2 or
A3
3. Connect the remote control socket to the mains power supply.
4. Press the corresponding “ON”, “OFF” buttons on the transmitter to switch on and off the connected appliance
by remote control. (eg. on/off buttons 1 controls receiver A1, 2 controls receiver A2, 3 controls A3)
5. The indicator on the receiver blink once for every reception of power on/off
Caution
1. For safety reason, always switch off your appliance before connection and avoid setting up on rainy days.
2. Appliances to be connected to the remote control socket MUST NOT exceed the voltage and frequency
ratings as in “Specifications”.
3. To adjust the channel or the groups, always use a big screw driver with the same diameter as the adjustment
arrow at the back of the socket and receiver. A small screw driver will deform the plastic housing during
adjustment.
Specifications
EMW200R-UL,
1. Power Rating : 125V~, 60Hz, 1000W
2. Frequency: : 433.92 MHz
3. Distance: : 25 meters
EMW203T
Battery : CR2032
Frequency : 433.92 MHz
1. Distance : 25 meters max.
Holder:
Everflourish Electrical Co., Ltd.
Renjiu Village, Wuxiang Town, Yinzhou, Ningbo, 315111 P.R. China
EMW200R-UL+EMW203T (E).doc, P2/2
Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Prudence：
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Warning:
Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication.
Avertissement :
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé
pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de
brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type
d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication
satisfaisante