User manual
Quick Manual A Important notice This Quick Manual explains the basic settings and the setting of the NAS wireless flashgun(s). New functions add-in to NAS only support the new NAS flashgun models such as MGlOAs. i60A, Di700A and Air R receiver may not fully support to Air 105, please refer to the Appendix. For detailed instructions, please refer to: - Air 105 and NAS flashgun User Instruction Manual http://www.nissindigita|.com/download.html Memory The pairing setting is memorized and remains unchanged when power on/ off. Energy saving The display dims in 30 seconds. Automatically turns off in 2 mintues when Air 105 and camera are not in use. Press any button on Air 105 or the camera shutter to cancel the energy saving mode. Air 105 turns off in 60 minutes automatically when it is not in use. Turn on/off To turn off the Air 105 manually, press on/ off switch and hold it for 1 second. Appendix (1) This AF-assist light only supports SLR / D-SLR type camera. Fix lens camera / Mirrorless camera not supported (2) Please refer to the NAS flashgun user manual in http://www.nissindigita|.com/download.html (3) Nissin i60A, Di7OOA and Air R do not support Open Mode, Modeling Lighting, Channel 1, Basic Group D, Advanced Groups A B C D. Please refer to our compatibility chart in http://www.nissindigitalcom/downloadhtml . (4) Nissin i60A, Di7OOA and Air R do not support +/—O.3EV or +/- 0.6EV exposure setting interval in M / TTL mode of Air 105, the result of these kinds of setting will became in same of +/- 0.5EV flash output control. (5) H55 function available in compatible cameras only, please refer to: http://www.nissindigita|.com/download.html HSS/FP "’ For Nikon/Fujifilm: It is controlled by camera menu setting. For details, please refer to the camera user manual. For OIympus/Panasonic/Sony: It is controlled by Air 105. Hold HSS button for 1 second to enable or disable. For Canon : It is controlled by Air 105 and H55 button or camera menu setting will be fine. for Canon / Fujifilm / Nikon / (Micro) Four Third I Sony Pairing 8: control 1 (Dow Before the pairing begins, make sure your NAS flashgun(s) sets to Auto Channel modem. Turned off both of them and Air 105. QC‘L /© -/ © HOLD .tiroA MGIO arm 3 Sec. Hold the dedicated buttons”) on your NAS flashgun(s) for 3 seconds until you hear the beeping sound. i Blink! Hold both Panel Lock button and Power on/off button for 3 seconds until the Pilot light is blinking in orange colour. m HOLD 1 Sec. Hold Mode button for 1 second to open mode. Users need to turn off if they are using NAS flashgun(s) that do not support the Open mode. «Paired! Itl Memorized! NAS flashgun(s) and Air 105 stop beeping and blinking after the pairing is done. Pairing setting remains unchanged even both devices power off. Do not operate until the process finished. Basic Group Advance Group ABCD ABCD Press and hold 05 1 sec. to change to the advance group AECD Press the group selection button [Kiln-[IE] to select different group and press same buton again to end. To turn off the group by pressing when the group is blinking. Press 03 to enable or disable the model light on flash. grog as“; Adjust power 8: TTL Rotate the dial to adjust the Power of M mode / Flash exposure compensation ofTTL mode when the group is blinking. Press and hold 422006 to change zoom position when the group is blinking or rotate the dial to adjust manually. film Flash exposure For the basic groups A B C D : All groups work in the same mode. To change different mode by pressing M/TTL mode button. For the advanced groups of A B C D : TTL and M mode can work in 4 advanced groups. To change mode between M and TTL of a selected group, press "M/TTL" button when the group blinks. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)this device must accept any interference received, Including interference that may cause undesired operation. Nomenclature 1 Group selection button 8 Pilot button (Test flash button) 2 Group on/off button 9 Power On/Off switch 3 Modeling light button 10 Unlock button 4 Shutter cable socket (2.5mm) 11 Micro SD card slot 5 Mode Button (for firmware update) 6 LCD panel 12 Strap hole 7 Select dial with buttons 13 Battery compartment door Channel button 14 AF-assist light (1) H35 button 15 Hotshoe contacts Beep on/off button M.Zoom button Panel Lock/Unlock button (hold isec.) Channel Setting 1 8““"8/ HOLD 1 Sec. Hold the Channel button for 1 second to change wireless channel. Channels 1(3)- 8 Rotate the dial to select Channels 1(3) - 8. (i60A, Di700A and Air R do not support Channel 1. Set all items to same channel between Channels 2 - 8 for pairing and shooting.) Hold the Channel button for 1 second again to confirm. Change the Channel setting of NAS flashgun(s) same as Air 105. For details please refer to the specific user manual‘z. ) Auto Channel 9.7.8 When NAS flashgun(s) sets to Auto Channel mode, it automatic follows the Channel setting of Air 105 when the users are changing the flashgun(s). When NAS flashgun set and fix the Channel setting in Channels 1‘3) « 8 , they do not automatic follow the Channel setting of Air 105. User have to set NAS flashgun manually in the same channel as Air 105 to keep the pairing.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Create Date : 2017:09:25 17:40:25+08:00 Creator : Adobe Acrobat 9.1.2 Modify Date : 2017:09:25 17:40:36+08:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Metadata Date : 2017:09:25 17:40:36+08:00 Creator Tool : Adobe Acrobat 9.1.2 Format : application/pdf Document ID : uuid:fbff3acf-673d-4565-873e-2ddba1468e8b Instance ID : uuid:6140eb35-d38f-4d72-a01a-b8e2b29dee4c Producer : Adobe Acrobat 9.1.2 Image Conversion Plug-in Page Count : 1EXIF Metadata provided by EXIF.tools