Nokia Bell G240WZA Digital Home ONU User Manual 7368 ISAM ONT G 240WZ A Product Guide

Alcatel-Lucent Shanghai Bell Co. Ltd. Digital Home ONU 7368 ISAM ONT G 240WZ A Product Guide

Contents

User manual

Alcatel-Lucent 7368INTELLIGENT SERVICES ACCESS MANAGER ONTG-240WZ-A PRODUCT GUIDEAlcatel-Lucent ProprietaryThis document contains proprietary information of Alcatel-Lucent and is not to be disclosedor used except in accordance with applicable agreements.Copyright 2016 © Alcatel-Lucent. All rights reserved.G-240WZ-A PRODUCT GUIDER05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
When printed by Alcatel-Lucent, this document is printed on recycled paper.Alcatel-Lucent assumes no responsibility for the accuracy of the information presented, which is subject to change without notice. Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All other trademarks are the property of their respective owners.Copyright 2016 Alcatel-Lucent.All rights reserved.DisclaimersAlcatel-Lucent products are intended for commercial uses. Without the appropriate network design engineering, they must not be sold, licensed or otherwise distributed for use in any hazardous environments requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft navigation or communication systems, air traffic control, direct life-support machines, or weapons systems, in which the failure of products could lead directly to death, personal injury, or severe physical or environmental damage. The customer hereby agrees that the use, sale, license or other distribution of the products for any such application without the prior written consent of Alcatel-Lucent, shall be at the customer's sole risk. The customer hereby agrees to defend and hold Alcatel-Lucent harmless from any claims for loss, cost, damage, expense or liability that may arise out of or in connection with the use, sale, license or other distribution of the products in such applications.This document may contain information regarding the use and installation of non-Alcatel-Lucent products. Please note that this information is provided as a courtesy to assist you. While Alcatel-Lucent tries to ensure that this information accurately reflects information provided by the supplier, please refer to the materials provided with any non-Alcatel-Lucent product and contact the supplier for confirmation. Alcatel-Lucent assumes no responsibility or liability for incorrect or incomplete information provided about non-Alcatel-Lucent products.However, this does not constitute a representation or warranty. The warranties provided for Alcatel-Lucent products, if any, are set forth in contractual documentation entered into by Alcatel-Lucent and its customers.This document was originally written in English. If there is any conflict or inconsistency between the English version and any other version of a document, the English version shall prevail.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
Alcatel-Lucent 7368 ISAM ONT iiiEdition 01G-240WZ-A Product GuidePrefaceThis preface provides general information about the documentation set for optical network terminals (ONTs).ScopeThis documentation set provides information about safety, features and functionality, ordering, hardware installation and maintenance, and software installation procedures for the current release.AudienceThis documentation set is intended for planners, administrators, operators, and maintenance personnel involved in installing, upgrading, or maintaining the ONTs.Required knowledgeThe reader must be familiar with general telecommunications principles.Acronyms and initialismsThe expansions and optional descriptions of most acronyms and initialisms appear in the glossary.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
Prefaceiv Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideAssistance and ordering phone numbersAlcatel-Lucent provides global technical support through regional call centers. Phone numbers for the regional call centers are available at the following URL: http://www.alcatel-lucent.com/myaccess. For ordering information, contact your Alcatel-Lucent sales representative.Alcatel-Lucent quality processesAlcatel-Lucent’s ONT manufacturing, testing, and inspecting practices are in compliance with GR-1252-CORE and TL 9000 requirements. These requirements are documented in the Operations Quality Plan 8BD-00023-4204-QRZZA, the Alcatel North American Quality Manual 8BD-00001-0000-QRZZA, and the Wireline Network Quality Manual 8AB-83179-0001-QRAAA.The quality plans and practices adequately ensure that technical requirements and customer end-point requirements are met. The customer or its representatives may be allowed to perform on-site quality surveillance audits, as agreed upon during contract negotiations.Safety informationFor safety information, see the appropriate safety guidelines chapter.DocumentsDocuments are available using ALED or OLCS.Procedure 1 To download a ZIP file package of the customer documentation1Navigate to http://www.alcatel-lucent.com/myaccess and enter your user name and password. If you are a new user and require access to this service, please contact your Alcatel-Lucent sales representative.2From the Technical Content for drop-down menu, choose the product.3Click on Downloads: Electronic Delivery.4Choose Documentation from the drop-down menu and click Next.5Select the image from the drop-down menu and click Next.6Follow the on-screen directions to download the file.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
PrefaceAlcatel-Lucent 7368 ISAM ONT vEdition 01G-240WZ-A Product GuideProcedure 2 To access individual documentsIndividual PDFs of customer documents are also accessible through the Alcatel-Lucent Customer Support website.1Navigate to http://www.alcatel-lucent.com/myaccess and enter your user name and password. If you are a new user and require access to this service, please contact your Alcatel-Lucent sales representative.2From the Technical Content for drop-down menu, choose the product.3Click on Manuals and Guides to display a list of customer documents by title and part number. You can filter this list using the Release drop-down menu.4Click on the PDF to open or save the file.Special informationThe following are examples of how special information is presented in this document.Procedures with options or substepsWhen there are options in a procedure, they are identified by letters. When there are required substeps in a procedure, they are identified by roman numerals.Danger — Danger indicates that the described activity or situation may result in serious personal injury or death; for example, high voltage or electric shock hazards.Warning — Warning indicates that the described activity or situation may, or will, cause equipment damage or serious performance problems.Caution — Caution indicates that the described activity or situation may, or will, cause service interruption.Note — A note provides information that is, or may be, of special interest.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
Prefacevi Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideProcedure 3 Example of options in a procedureAt step 1, you can choose option a or b. At step 2, you must do what the step indicates.1This step offers two options. You must choose one of the following:aThis is one option.bThis is another option.2You must perform this step.Procedure 4 Example of required substeps in a procedureAt step 1, you must perform a series of substeps within a step. At step 2, you must do what the step indicates.1This step has a series of substeps that you must perform to complete the step. You must perform the following substeps:iThis is the first substep.ii This is the second substep.iii This is the third substep.2 You must perform this step.Multiple PDF document searchYou can use Adobe Reader Release 6.0 and later to search multiple PDF files for a common term. Adobe Reader displays the results in a single display panel. The results are grouped by PDF file, and you can expand the entry for each file.Procedure 5 To search multiple PDF files for a common term1Open Adobe Acrobat Reader.2Choose Edit→Search from the Acrobat Reader main menu. The Search PDF panel appears.3Enter the search criteria.Note — The PDF files in which you search must be in the same folder.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
PrefaceAlcatel-Lucent 7368 ISAM ONT viiEdition 01G-240WZ-A Product Guide4Click on the All PDF Documents In radio button.5Select the folder in which to search using the drop-down menu.6Click on the Search button.Acrobat Reader displays the search results. You can expand the entries for each document by clicking on the + symbol.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
Prefaceviii Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
Alcatel-Lucent 7368 ISAM ONT ixEdition 01G-240WZ-A Product GuideETSI ONT safety guidelinesThis chapter provides information about the mandatory regulations that govern the installation and operation of the optical network terminals (ONTs).Safety instructionsThis section describes the safety instructions that are provided in the ONT customer documentation and on the equipment.Safety instruction boxesThe safety instruction boxes are provided in the ONT customer documentation. Observe the instructions to meet safety requirements.The following is an example of the Danger box.The Danger box indicates that the described activity or situation may pose a threat to personal safety. It calls attention to a situation or procedure which, if not correctly performed or adhered to, may result in death or serious physical harm. Do not proceed beyond a Danger box until the indicated conditions are fully understood and met.The following is an example of the Warning box.Danger — Possibility of personal injury. Warning 1 — Possibility of equipment damage.Warning 2 — Possibility of data loss.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ETSI ONT safety guidelinesxAlcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideThe Warning box indicates that the described activity or situation may, or will, cause equipment damage, loss of data, or serious performance problems. It identifies a possible equipment-damaging situation or provides essential information to avoid the degradation of system operations or data.Do not proceed beyond a warning until the indicated conditions are fully understood and met.The following is an example of the Caution box.The Caution box indicates that the described activity or situation may, or will, cause service interruption.Do not proceed beyond a caution until the indicated conditions are fully understood and met.The following is an example of the Note box.The Note box provides information that assists the personnel working with ONTs. It does not provide safety-related instructions.Safety-related labelsThe ONT equipment is labeled with the specific safety instructions and compliance information that is related to a variant of the ONT. Observe the instructions on the safety labels.Table 1 provides sample safety labels on the ONT equipment.Table 1 Safety labelsFigure 1 shows the PSE certification.Caution 1 — Possibility of service interruption.Caution 2 — Service interruption.Note — Information of special interest.Description Label textESD warning Caution: This assembly contains an electrostatic sensitive device.Laser classification Class 1 laser productPSE marking These power supplies are Japan PSE certified and compliant with Japan VCCI emissions standards.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ETSI ONT safety guidelinesAlcatel-Lucent 7368 ISAM ONT xiEdition 01G-240WZ-A Product GuideFigure 1 PSE certificationSafety standards complianceThis section describes the ONT compliance with the European safety standards.EMC, EMI, and ESD complianceThe ONT equipment complies with the following EMC, EMI, and ESD requirements:•EN 300-386 V1.5.1: Electromagnetic Compatibility and Radio Spectrum Matters (ERM): Telecommunications Network Equipment; Electromagnetic Compatibility (EMC) requirements; Electrostatic Discharge (ESD) requirements•EN 55022 (2006): Class B, Information Technology Equipment, Radio Disturbance Characteristics, limits and methods of measurement•EN 55024 (2010): Information Technology Equipment, Immunity Characteristics, limits and methods of measurement•European Council Directive 2004/108/EC•EN 300-386 V1.4.1: 2008•EN 55022:2006 Class B (ONTs)Equipment safety standard complianceThe ONT equipment complies with the requirements of EN 60950-1, Safety of Information Technology Equipment for use in a restricted location (per R-269).Environmental standard complianceThe ONT equipment complies with the EN 300 019 European environmental standards.Laser product standard complianceFor most ONTs, the ONT equipment complies with EN 60825-1 and IEC 60825-2 for laser products. If there is an exception to this compliance regulation, you can find this information in the standards compliance section of the unit data sheet in this Product Guide.This is a Class B product based on the standard of the Voluntary Control Council for Interferencefrom Information Technology Equipment (VCCI). If this is used near a radio or television receiver ina domestic environment, it may cause radio interference. Install and use the equipment accordingto the instruction manual. Warning19841R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ETSI ONT safety guidelinesxii Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideResistibility requirements complianceThe ONT equipment complies with the requirements of ITU Recommendation K.21 for resistibility of telecommunication equipment installed in customer premises to over voltage and overcurrents.Acoustic noise emission standard complianceThe ONT equipment complies with EN 300 753 acoustic noise emission limit and test methods. Electrical safety guidelinesThis section provides the electrical safety guidelines for the ONT equipment.Power suppliesThe use of any non-Alcatel-Lucent approved power supplies or power adapters is not supported or endorsed by Alcatel-Lucent. Such use will void any warranty or support contract with Alcatel-Lucent. Such use greatly increases the danger of damage to equipment or property.CablingThe following are the guidelines regarding cables used for the ONT equipment:•All cables must be approved by the relevant national electrical code.•The cables for outdoor installation of ONTs must be suitable for outdoor use.• POTS wiring run outside the subscriber premises must comply with the requirements of local electrical codes. In some markets, the maximum allowed length of the outside run is 140 feet (43 m). If the outside run is longer, NEC requires primary protection at both the exit and entry points for the wire.Protective earthEarthing and bonding of the ONTs must comply with the requirements of local electrical codes.Note 1 — The ONTs comply with the U.S. National Electrical Code. However, local electrical authorities have jurisdiction when there are differences between the local and U.S. standards.Note 2 — The ONTs comply with BS EN 61140.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ETSI ONT safety guidelinesAlcatel-Lucent 7368 ISAM ONT xiiiEdition 01G-240WZ-A Product GuideESD safety guidelinesThe ONT equipment is sensitive to ESD. Operations personnel must observe the following ESD instructions when they handle the ONT equipment. During installation and maintenance, service personnel must wear wrist straps to prevent damage caused by ESD.Laser safety guidelinesObserve the following instructions when you perform installation, operations, and maintenance tasks on the ONT equipment.Only qualified service personnel who are extremely familiar with laser radiation hazards should install or remove the fiber optic cables and units in this system.Observe the following danger for laser hazard. Eyes can be damaged when they are exposed to a laser beam. Take necessary precautions before you plug in the optical modules.Laser classificationThe ONT is classified as a Class 1 laser product based on its transmit optical output.Laser warning labelsThe following figures show the labels related to laser product, classification and warning. Figure 2 shows a laser product label.Caution — This equipment is ESD sensitive. Proper ESD protections should be used when you enter the TELCO Access portion of the ONT.Danger — There may be invisible laser radiation at the fiber optic cable when the cable is removed from the connector. Avoid direct exposure to the laser beam.Danger — Possibility of equipment damage. Risk of eye damage by laser radiation.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ETSI ONT safety guidelinesxiv Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideFigure 2 Laser product labelFigure 3 shows a laser classification label. Laser classification labels may be provided in other languages.Figure 3 Laser classification labelFigure 4 shows a laser warning label and an explanatory label for laser products. Labels and warning may be provided in other languages. The explanatory label provides the following information: •a warning that calls attention to the invisible laser radiation•an instruction against staring into the beam or viewing directly with optical instruments•wavelength•normal output power•maximum output power18455LASER CLASSE 1CLASE 1 DEL LASERCLASS 1 LASER PRODUCT PRODUCTO LASER CLASE 118992''R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ETSI ONT safety guidelinesAlcatel-Lucent 7368 ISAM ONT xvEdition 01G-240WZ-A Product GuideFigure 4 Laser warning labelsTransmit optical outputThe maximum transmit optical output of an ONT is +5 dBm.Normal laser operationIn normal operation, fiber cable laser radiation is always off until it receives signal from the line terminal card.Eyes can be damaged when they exposed to a laser beam. Operating personnel must observe the instructions on the laser explanatory label before plugging in the optical module.Location classUse cable supports and guides to protect the receptacles from strain.INVISIBLE LASER RADIATIONDO NOT STARE INTO BEAMOR VIEW DIRECTLY WITHOPTICAL INSTRUMENTSWavelength(s): xxxx nmNormal output power: xx m WMax output power: yyy m WLaser Warning Label Laser Warning LabelCLASS 1 LASER PRODUCTINVISIBLE LASER RADIATION PRESENT AT FIBER OPTIC CABLEWHEN NOT CONNECTED. AVOID DIRECT EXPOSURE TO BEAM.RAYONNEMENT LASER CLASSE 1RAYONNEMENT LASER INVISIBLEEVITER TOUTE EXPOSITION AU FAISCEAUNE PAS DEMONTER. FAIRE APPEL A UN PERSONNELL QUALIFIECLASE 1 DEL LASERRADIACION DE LASER INVISIBLE. EVITAR CUALOUIER EXPOSICION ALRAYO LASER. NO DESMONTAR. LLAMAR A PERSONAL AUTORIZADOLaser Warning Label18993'Danger — Risk of eye damage by laser radiation.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ETSI ONT safety guidelinesxvi Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideEnvironmental requirementsSee the ONT technical specification documentation for more information about temperature ranges.During operation in the supported temperature range, condensation inside the ONT caused by humidity is not an issue. To avoid condensation caused by rapid changes in temperature and humidity, Alcatel-Lucent recommends:•The door of the ONT not be opened until temperature inside and outside the enclosure has stabilized.•If the door of the ONT must be opened after a rapid change in temperature or humidity, use a dry cloth to wipe down the metal interior to prevent the risk of condensation.•When high humidity is present, installation of a cover or tent over the ONT helps prevent condensation when the door is opened.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
Alcatel-Lucent 7368 ISAM ONT xviiEdition 01G-240WZ-A Product GuideETSI environmental and CRoHS guidelinesThis chapter provides information about the ETSI environmental China Restriction of Hazardous Substances (CRoHS) regulations that govern the installation and operation of the optical line termination (OLT) and optical network termination (ONT) systems. This chapter also includes environmental operation parameters of general interest.Environmental labelsThis section describes the environmental instructions that are provided with the customer documentation, equipment, and location where the equipment resides.OverviewCRoHS is applicable to Electronic Information Products (EIP) manufactured or sold and imported in the territory of the mainland of the People’s Republic of China. EIP refers to products and their accessories manufactured by using electronic information technology, including electronic communications products and such subcomponents as batteries and cables.Environmental related labelsEnvironmental labels are located on appropriate equipment. The following are sample labels.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ETSI environmental and CRoHS guidelinesxviii Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideProducts below Maximum Concentration Value (MCV) labelFigure 1 shows the label that indicates a product is below the maximum concentration value, as defined by standard SJ/T11363-2006 (Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products). Products with this label are recyclable. The label may be found in this documentation or on the product.Figure 1 Products below MCV value labelProducts containing hazardous substances above Maximum Concentration Value (MCV) labelFigure 2 shows the label that indicates a product is above the maximum concentration value, as defined by standard SJ/T11363-2006 (Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products). The number contained inside the label indicates the Environment-Friendly User Period (EFUP) value. The label may be found in this documentation or on the product.18986R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ETSI environmental and CRoHS guidelinesAlcatel-Lucent 7368 ISAM ONT xixEdition 01G-240WZ-A Product GuideFigure 2 Products above MCV value labelTogether with major international telecommunications equipment companies, Alcatel-Lucent has determined it is appropriate to use an EFUP of 50 years for network infrastructure equipment and an EFUP of 20 years for handsets and accessories. These values are based on manufacturers' extensive practical experience of the design, manufacturing, maintenance, usage conditions, operating environments, and physical condition of infrastructure and handsets after years of service. The values reflect minimum values and refer to products operated according to the intended use conditions. See “Hazardous Substances Table (HST)” for more information.Hazardous Substances Table (HST)This section describes the compliance of the OLT and ONT equipment to the CRoHS standard when the product and subassemblies contain hazardous substances beyond the MCV value. This information is found in this user documentation where part numbers for the product and subassemblies are listed. It may be referenced in other OLT and ONT documentation.In accordance with the People’s Republic of China Electronic Industry Standard Marking for the Control of Pollution Caused by Electronic Information Products (SJ/T11364-2006), customers may access the Alcatel-Lucent Hazardous Substance Table, in Chinese, from the following location:•http://www.alcatel-sbell.com.cn/wwwroot/images/upload/private/1/media/ChinaRoHS.pdfOther environmental requirementsObserve the following environmental requirements when handling the P-OLT or ONT equipment.18985R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ETSI environmental and CRoHS guidelinesxx Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideONT environmental requirementsSee the ONT technical specification documentation for more information about temperature ranges.StorageAccording to ETS 300-019-1-1 - Class 1.1, storage of OLT equipment must be in Class 1.1, weather-protected, temperature-controlled locations.TransportationAccording to EN 300-019-1-2 - Class 2.3, transportation of the OLT equipment must be in packed, public transportation with no rain on packing allowed.Stationary useAccording to EN 300-019-1-3 - Class 3.1/3.2/3.E, stationary use of OLT equipment must be in a temperature-controlled location, with no rain allowed, and with no condensation allowed.Thermal limitationsWhen the OLT is installed in the CO or CEV, install air filters on the P-OLT. The thermal limitations for OLT operation in a CO or CEV are:•operating temperature: 5°C to 40°C (41°F to 104°F)•short-term temperature: –5°C to 50°C (23°F to 122°F)•operating relative humidity: 5% to 85%•short-term relative humidity: 5% to 95%, but not to exceed 0.024 kg of water/kgMaterial content complianceEuropean Union (EU) Directive 2002/95/EC, “Restriction of the use of certain Hazardous Substances” (RoHS), restricts the use of lead, mercury, cadmium, hexavalent chromium, and certain flame retardants in electrical and electronic equipment. This Directive applies to electrical and electronic products placed on the EU market after 1 July 2006, with various exemptions, including an exemption for lead solder in network infrastructure equipment. Alcatel-Lucent products shipped to the EU after 1 July 2006 comply with the EU RoHS Directive.Alcatel-Lucent has implemented a material/substance content management process. The process is described in: Alcatel-Lucent process for ensuring RoHS Compliance (1AA002660031ASZZA). This ensures compliance with the European Union Directive 2011/65/EU on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS2). With the process equipment is assessed in accordance with the Harmonised Standard EN50581:2012 (CENELEC) on Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous substances.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ETSI environmental and CRoHS guidelinesAlcatel-Lucent 7368 ISAM ONT xxiEdition 01G-240WZ-A Product GuideEnd-of-life collection and treatmentElectronic products bearing or referencing the symbol shown in Figure 3, when put on the market within the European Union (EU), shall be collected and treated at the end of their useful life, in compliance with applicable EU and local legislation. They shall not be disposed of as part of unsorted municipal waste. Due to materials that may be contained in the product, such as heavy metals or batteries, the environment and human health may be negatively impacted as a result of inappropriate disposal.Figure 3 Recycling/take back/disposal of product symbolAt the end of their life, the OLT and ONT products are subject to the applicable local legislations that implement the European Directive 2012/19EU on waste electrical and electronic equipment (WEEE).There can be different requirements for collection and treatment in different member states of the European Union. In compliance with legal requirements and contractual agreements, where applicable, Alcatel-Lucent will offer to provide for the collection and treatment of Alcatel-Lucent products bearing the logo shown in Figure 3 at the end of their useful life, or products displaced by Alcatel-Lucent equipment offers. For information regarding take-back of equipment by Alcatel-Lucent, or for more information regarding the requirements for recycling/disposal of product, contact your Alcatel-Lucent account manager or Alcatel-Lucent take back support at takeback@alcatel-lucent.com.Note — In the European Union, a solid bar under the symbol for a crossed-out wheeled bin indicates that the product was put on the market after 13 August 2005.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ETSI environmental and CRoHS guidelinesxxii Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
Alcatel-Lucent 7368 ISAM ONT xxiiiEdition 01G-240WZ-A Product GuideANSI ONT safety guidelinesThis chapter provides information about the mandatory regulations that govern the installation and operation of the optical network terminals or units (ONTs or ONUs) in the North American or ANSI market.Safety instructionsThis section describes the safety instructions that are provided in the ONT customer documentation and on the equipment.Safety instruction boxes in customer documentationThe safety instruction boxes are provided in the ONT customer documentation. Observe the instructions to meet safety requirements.The following is an example of the Danger box.The Danger box indicates that the described activity or situation may pose a threat to personal safety. It calls attention to a situation or procedure which, if not correctly performed or adhered to, may result in death or serious physical harm. Do not proceed beyond a Danger box until the indicated conditions are fully understood and met.Danger — Possibility of personal injury. R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ANSI ONT safety guidelinesxxiv Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideThe following is an example of the Warning box.The Warning box indicates that the described activity or situation may, or will, cause equipment damage, loss of data, or serious performance problems. It identifies a possible equipment-damaging situation or provides essential information to avoid the degradation of system operations or data.Do not proceed beyond a warning until the indicated conditions are fully understood and met.The following is an example of the Caution box.The Caution box indicates that the described activity or situation may, or will, cause service interruption.Do not proceed beyond a caution until the indicated conditions are fully understood and met.The following is an example of the Note box.The Note box provides information that assists the personnel working with ONTs. It does not provide safety-related instructions.Safety-related labelsThe ONT equipment is labeled with specific safety compliance information and instructions that are related to a variant of the ONT. Observe the instructions on the safety labels.Table 1 provides examples of the text in the various ONT safety labels.Table 1 Safety labelsWarning 1 — Possibility of equipment damage.Warning 2 — Possibility of data loss.Caution 1 — Possibility of service interruption.Caution 2 — Service interruption.Note — Information of special interest.Description Label textUL compliance Communication service equipment US listed. Type 3R enclosure - Rainproof.TUV compliance Type 3R enclosure - Rainproof.ESD warning Caution: This assembly contains electrostatic sensitive device.(1 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ANSI ONT safety guidelinesAlcatel-Lucent 7368 ISAM ONT xxvEdition 01G-240WZ-A Product GuideFigure 1 shows a sample safety label on the ONT equipment.Figure 1 Sample safety label on the ONT equipmentSafety standards complianceThis section describes the ONT compliance with North American safety standards.Laser classification Class 1 laser productLaser product compliance This laser product conforms to all applicable standards of 21 CFR 1040.10 at date of manufacture.FCC standards compliance Tested to comply with FCC standards for home or office use.CDRH compliance Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007Operation conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Canadian standard compliance (modular ONT) This Class A digital apparatus complies with Canadian ICES-003. Canadian standard compliance (outdoor ONT) This Class B digital apparatus complies with Canadian ICES-003. CE marking There are various CE symbols for CE compliance.Description Label text(2 of 2)18533This device complies with Part 15 of the FCC Rules. Operation is subjectto the following two conditions: (1) this device may not cause harmfulinterference, and (2) this device must accept any interferencereceived, including interference that may cause undesired operation.This Class A digital apparatus complies with Canadian ICES-003. Cet appareilnumerique de la class A est conforme a la norme NMB-003 du CanadaTested to Complywith FCC StandardsFOR HOME OR OFFICE USECOMMUNICATION SERVICE EQUIPMENTUS LISTED27FYType 3R Enclosure - RainproofCAUTIONThis Assembly Contains Electrostatic Sensitive Devicesc®Warning — Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ANSI ONT safety guidelinesxxvi Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideEMC, EMI, and ESD standards complianceThe ONT equipment complies with the following requirements:•Federal Communications Commission (FCC) CFR 47, Part 15, Subpart B, Class A requirements for OLT equipment•GR-1089-CORE requirements, including:•Section 3 Electromagnetic Interference, Emissions Radiated and Conducted•Section 3 Immunity, Radiated and Conducted•Section 2 ESD Discharge Immunity: System Level Electrostatic Discharge and EFT Immunity: Electrically Fast TransientsThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver is needed.•Consult the dealer or an experienced radio/TV technician for help.Equipment safety standard complianceThe ONT equipment complies with the requirements of UL60950-1, Outdoor ONTs to “Communication Service Equipment” (CSE) and Indoor ONTs to Information Technology Equipment (ITE).Environmental standards complianceThe ONT equipment complies with the following standards:•GR-63-CORE (NEBS): requirements related to operating, storage, humidity, altitude, earthquake, office vibration, transportation and handling, fire resistance and spread, airborne contaminants, illumination, and acoustic noise•GR-487-CORE: requirements related to rain, chemical, sand, and dust•GR-487 R3-82: requirements related to condensation •GR-3108: Requirements for Network Equipment in the Outside Plant (OSP)•TP76200: Common Systems Equipment Interconnections StandardsR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ANSI ONT safety guidelinesAlcatel-Lucent 7368 ISAM ONT xxviiEdition 01G-240WZ-A Product GuideLaser product standards complianceThe ONT equipment complies with 21 CFR 1040.10 and CFR 1040.11, except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007” or to 21 CFR 1040.10 U.S. Center for Devices and Radiological Health (CDRH) of the Food and Drug Administration (FDA) Laser Notice 42 for ONTs containing Class 1 Laser modules certified by original manufactures.Per CDRH 21 CFR 10.40.10 (h) (1) (iv) distributors of Class 1 laser products, such as ALU ONTs shall leave the following Laser Safety cautions with the end user.a) “Class 1 Laser Product”b) “Caution – Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.”Figure 2 shows a laser product label.Figure 2 Sample laser product label showing CDRH 21 CFR complianceResistibility requirements complianceThe ONT equipment complies with the requirements of ITU Recommendation K.21 for resistibility of telecommunication equipment installed in customer premises to overvoltage and overcurrents.Laser safety guidelinesOnly qualified service personnel who are extremely familiar with laser radiation hazards should install or remove the fiber optic cables and units in this system.Observe the following warnings when you perform installation, operations, and maintenance tasks on the ONT equipment.FiOS EnabledTo Order FiOS: 888 GET-FiOSor visit Verizon.comFor Service: 888 553-15552301 Sugar Bush Rd.Raleigh, NC 27612No User Serviceable Parts Inside. Refer All Servicing To Qualified Personnel.Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007.4P92I.T.E 12VDC 2.5A22813Danger — There may be invisible laser radiation at the fiber optic cable when the cable is removed from the connector. Avoid direct exposure to beam.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ANSI ONT safety guidelinesxxviii Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideObserve the following danger for a laser hazard. Eyes can be damaged when they are exposed to a laser beam. Take necessary precautions before you plug in the optical modules.Per CDRH 21 CFR 10.40.10 (h) (1) (iv) distributors of Class 1 laser products, such as ALU ONTs shall leave the following Laser Safety cautions with the end user.a) “Class 1 Laser Product”b) “Caution – Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.”Laser warning labelsThe following figures show sample labels related to laser product, classification and warning. Figure 3 shows a laser product label.Figure 3 Laser product labelFigure 4 shows a laser classification label. Laser classification labels may be provided in other languages.Figure 4 Laser classification labelDanger — Possibility of equipment damage. Risk of eye damage by laser radiation.18455LASER CLASSE 1CLASE 1 DEL LASERCLASS 1 LASER PRODUCT PRODUCTO LASER CLASE 118992''R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ANSI ONT safety guidelinesAlcatel-Lucent 7368 ISAM ONT xxixEdition 01G-240WZ-A Product GuideFigure 5 shows a laser warning label and an explanatory label for laser products. Explanatory labels may be provided in other languages. The explanatory label provides the following information: •a warning that calls attention to the invisible laser radiation•an instruction against staring into the beam or viewing directly with optical instruments•wavelength•normal output power•maximum output powerFigure 5 Laser warning labelsLaser classificationThe ONT is classified as a Class 1 laser product based on its transmit optical output. For Class 1 laser products, lasers are safe under reasonably foreseeable conditions of operation, including the use of optical instruments for intrabeam viewing.Figure 6 shows a sample laser product safety label on the ONT equipment.INVISIBLE LASER RADIATIONDO NOT STARE INTO BEAMOR VIEW DIRECTLY WITHOPTICAL INSTRUMENTSWavelength(s): xxxx nmNormal output power: xx m WMax output power: yyy m WLaser Warning Label Laser Warning LabelCLASS 1 LASER PRODUCTINVISIBLE LASER RADIATION PRESENT AT FIBER OPTIC CABLEWHEN NOT CONNECTED. AVOID DIRECT EXPOSURE TO BEAM.RAYONNEMENT LASER CLASSE 1RAYONNEMENT LASER INVISIBLEEVITER TOUTE EXPOSITION AU FAISCEAUNE PAS DEMONTER. FAIRE APPEL A UN PERSONNELL QUALIFIECLASE 1 DEL LASERRADIACION DE LASER INVISIBLE. EVITAR CUALOUIER EXPOSICION ALRAYO LASER. NO DESMONTAR. LLAMAR A PERSONAL AUTORIZADOLaser Warning Label18993'R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ANSI ONT safety guidelinesxxx Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideFigure 6 Sample laser product safety label on the ONT equipmentTransmit optical outputThe maximum transmit optical output of an ONT is +5 dBm.Normal laser operationIn normal operation, fiber cable laser radiation is always off until it receives signal from the line terminal card.Operating personnel must observe the instructions on the laser explanatory label before plugging in the optical module.Location classUse cable supports and guides to protect the receptacles from strain.Electrical safety guidelinesThis section provides the electrical safety guidelines for the ONT equipment.Power suppliesThe use of any non-Alcatel-Lucent approved power supplies or power adapters is not supported or endorsed by Alcatel-Lucent. Such use will void any warranty or support contract with Alcatel-Lucent. Such use greatly increases the danger of damage to equipment or property.CLASS 1 LASER PRODUCTTHIS LASER PRODUCT CONFORMS TO ALL APPLICABLESTANDARDS OF 21 CFR 1040.10 AT DATE OF MANUFACTURE.MANUFACTURED:MONTH YEAR18532Danger — Risk of eye damage by laser radiation.Note — The ONTs comply with the U.S. National Electrical Code. However, local electrical authorities have jurisdiction when there are differences between the local and U.S. standards.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ANSI ONT safety guidelinesAlcatel-Lucent 7368 ISAM ONT xxxiEdition 01G-240WZ-A Product GuideCablingThe following are the guidelines regarding cables used for the ONT equipment:•Use only cables approved by the relevant national electrical code.•Use cables suitable for outdoor use for outdoor installation of ONTs.•The ONTs have been evaluated for use with external POTS wiring without primary protection that may not exceed 140 ft (43 m) in reach. However, the power cable must not exceed 100 ft (31 m).Protective earthEarthing and bonding of the ONTs must comply with the requirements of NEC article 250 or local electrical codes.ESD safety guidelinesThe ONT equipment is sensitive to ESD. Operations personnel must observe the following ESD instructions when they handle the ONT equipment. During installation and maintenance, service personnel must wear wrist straps to prevent damage caused by ESD.Alcatel-Lucent recommends that you prepare the site before you install the ONT equipment. In addition, you must control relative humidity, use static dissipating material for furniture or flooring, and restrict the use of air conditioning.Environmental requirementsSee the ONT technical specification documentation for temperature ranges for ONTs.During operation in the supported temperature range, condensation inside the ONT caused by humidity is not an issue. To avoid condensation caused by rapid changes in temperature and humidity, Alcatel-Lucent recommends:•The door of the ONT not be opened until temperature inside and outside the enclosure has stabilized.•If the door of the ONT must be opened after a rapid change in temperature or humidity, use a dry cloth to wipe down the metal interior to prevent the risk of condensation.•When high humidity is present, installation of a cover or tent over the ONT helps prevent condensation when the door is opened.Caution — This equipment is ESD sensitive. Proper ESD protections should be used when entering the TELCO Access portion of the ONT.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ANSI ONT safety guidelinesxxxii Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
Alcatel-Lucent 7368 ISAM ONT xxxiiiEdition 01G-240WZ-A Product GuideContentsPreface iiiScope ...............................................................................................iiiAudience ...............................................................................................iiiRequired knowledge...................................................................................iiiAcronyms and initialisms .............................................................................iiiAssistance and ordering phone numbers ........................................................... ivAlcatel-Lucent quality processes.................................................................... ivSafety information..................................................................................... ivDocuments .............................................................................................. ivProcedure 1 To download a ZIP file package of the customerdocumentation.................................................................... ivProcedure 2 To access individual documents ......................................vSpecial information.....................................................................................vProcedures with options or substeps.................................................vProcedure 3 Example of options in a procedure.................................. viProcedure 4 Example of required substeps in a procedure..................... viMultiple PDF document search....................................................................... viProcedure 5 To search multiple PDF files for a common term................. viETSI ONT safety guidelines ixSafety instructions..................................................................................... ixSafety instruction boxes .............................................................. ixSafety-related labels ...................................................................xSafety standards compliance......................................................................... xiEMC, EMI, and ESD compliance....................................................... xiEquipment safety standard compliance ............................................ xiEnvironmental standard compliance ................................................ xiLaser product standard compliance................................................. xiR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
Contentsxxxiv Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideResistibility requirements compliance............................................. xiiAcoustic noise emission standard compliance .................................... xiiElectrical safety guidelines.......................................................................... xiiPower supplies......................................................................... xiiCabling.................................................................................. xiiProtective earth....................................................................... xiiESD safety guidelines................................................................................ xiiiLaser safety guidelines.............................................................................. xiiiLaser classification................................................................... xiiiTransmit optical output.............................................................. xvNormal laser operation............................................................... xvLocation class.......................................................................... xvEnvironmental requirements........................................................................xviETSI environmental and CRoHS guidelines xviiEnvironmental labels................................................................................xviiOverview ..............................................................................xviiEnvironmental related labels.......................................................xviiHazardous Substances Table (HST).................................................................xixOther environmental requirements ................................................................xixONT environmental requirements .................................................. xxStorage.................................................................................. xxTransportation......................................................................... xxStationary use ......................................................................... xxThermal limitations................................................................... xxMaterial content compliance........................................................ xxEnd-of-life collection and treatment ..............................................xxiANSI ONT safety guidelines xxiiiSafety instructions.................................................................................. xxiiiSafety instruction boxes in customer documentation ......................... xxiiiSafety-related labels ............................................................... xxivSafety standards compliance....................................................................... xxvEMC, EMI, and ESD standards compliance ....................................... xxviEquipment safety standard compliance ......................................... xxviEnvironmental standards compliance............................................ xxviLaser product standards compliance.............................................xxviiResistibility requirements compliance...........................................xxviiLaser safety guidelines.............................................................................xxviiLaser warning labels...............................................................xxviiiLaser classification.................................................................. xxixTransmit optical output............................................................. xxxNormal laser operation.............................................................. xxxLocation class......................................................................... xxxR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ContentsAlcatel-Lucent 7368 ISAM ONT xxxvEdition 01G-240WZ-A Product GuideElectrical safety guidelines......................................................................... xxxPower supplies........................................................................ xxxCabling................................................................................ xxxiProtective earth..................................................................... xxxiESD safety guidelines............................................................................... xxxiEnvironmental requirements...................................................................... xxxi1 — G-240WZ-A unit data sheet 1-11.1 G-240WZ-A part numbers and identification........................................ 1-21.2 G-240WZ-A general description....................................................... 1-2Configuring the G-240W-A to function as a single port ONT .................. 1-4TR-069 support for reading optical parameters ................................. 1-4TR-069 object support for WiFi parameters ..................................... 1-4TR-104 parameter extension support for voice service ........................ 1-4Mobile offload support .............................................................. 1-5Bridged Residential Gateway (BRG) support..................................... 1-51.3 G-240WZ-A software and installation feature support ............................ 1-51.4 G-240WZ-A interfaces and interface capacity...................................... 1-6G-240WZ-A connections and components ........................................ 1-61.5 G-240WZ-A LEDs......................................................................... 1-71.6 G-240WZ-A detailed specifications................................................... 1-91.7 G-240WZ-A GEM ports and T-CONTs.................................................1-101.8 G-240WZ-A performance monitoring statistics ....................................1-111.9 G-240WZ-A functional blocks.........................................................1-121.10 G-240WZ-A standards compliance...................................................1-14Energy-related products standby and off modes compliance ................1-15FCC statement.......................................................................1-15FCC Radiation Exposure Statement ..............................................1-151.11 G-240WZ-A special considerations...................................................1-16Wi-Fi service .........................................................................1-16G-240WZ-A ONT considerations and limitations................................1-162 — Install a G-240WZ-A indoor ONT 2-12.1 Purpose ................................................................................... 2-22.2 General ................................................................................... 2-22.3 Prerequisites............................................................................. 2-22.4 Recommended tools .................................................................... 2-22.5 Safety information ...................................................................... 2-32.6 Procedure ................................................................................ 2-43 — Replace a G-240WZ-A indoor ONT 3-13.1 Purpose ................................................................................... 3-23.2 General ................................................................................... 3-23.3 Prerequisites............................................................................. 3-23.4 Recommended tools .................................................................... 3-23.5 Safety information ...................................................................... 3-33.6 Procedure ................................................................................ 3-4R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
Contentsxxxvi Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product Guide4 — Configure a G-240WZ-A indoor ONT 4-14.1 General ................................................................................... 4-24.2 HGU mode GUI configuration.......................................................... 4-2Login ................................................................................... 4-2Procedure 4-1 Login to web-based GUI .......................................... 4-2Device and connection status ...................................................... 4-3Procedure 4-2 Device information retrieval..................................... 4-4Procedure 4-3 LAN status retrieval............................................... 4-5Procedure 4-4 WAN status retrieval .............................................. 4-7Procedure 4-5 WAN status IPv6 retrieval ........................................ 4-8Procedure 4-6 Home networking information retrieval ......................4-10Procedure 4-7 Optics module status retrieval .................................4-11Procedure 4-8 Voice information retrieval.....................................4-12Network configuration..............................................................4-13Procedure 4-9 LAN networking configuration..................................4-13Procedure 4-10 LAN IPv6 networking configuration...........................4-14Procedure 4-11 WAN networking configuration................................4-16Procedure 4-12 WAN DHCP configuration.......................................4-17Procedure 4-13 WiFi 2.4G networking configuration .........................4-18Procedure 4-14 WiFi 5G networking configuration............................4-20Procedure 4-15 Routing configuration ..........................................4-21Procedure 4-16 DNS configuration...............................................4-22Procedure 4-17 TR-069 configuration ...........................................4-23Security configuration..............................................................4-24Procedure 4-18 Firewall configuration..........................................4-24Procedure 4-19 MAC filter configuration .......................................4-25Procedure 4-20 IP filter configuration ..........................................4-26Procedure 4-21 DMZ and ALG configuration....................................4-27Application configuration..........................................................4-28Procedure 4-22 Port forwarding configuration ................................4-28Procedure 4-23 DDNS configuration .............................................4-29Procedure 4-24 NTP configuration...............................................4-30Procedure 4-25 USB storage configuration .....................................4-31Procedure 4-26 UPnP and DLNA configuration.................................4-32Maintenance .........................................................................4-32Procedure 4-27 Password configuration ........................................4-33Procedure 4-28 SLID configuration ..............................................4-34Procedure 4-29 Device management ............................................4-35Procedure 4-30 Backup and restore .............................................4-36Procedure 4-31 Upgrade firmware...............................................4-36Procedure 4-32 Reboot ONT ......................................................4-37Procedure 4-33 Restore factory defaults .......................................4-38Procedure 4-34 Diagnose connections...........................................4-39Procedure 4-35 View log files ....................................................4-40RG troubleshooting counters ......................................................4-41Procedure 4-36 Retrieve Residential Gateway (RG)troubleshooting counters ....................................................4-41Smart Home configuration.........................................................4-42Procedure 4-37 Configure home monitoring systems .........................4-424.3 SFU mode configuration...............................................................4-44Switch from default HGU mode to SFU mode...................................4-44Procedure 4-38 Switching to SFU mode.........................................4-44R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ContentsAlcatel-Lucent 7368 ISAM ONT xxxviiEdition 01G-240WZ-A Product GuideProcedure 4-39 Modifying the operator ID .....................................4-44Login ..................................................................................4-45Procedure 4-40 Login to web-based GUI........................................4-45Device and connection status .....................................................4-46Procedure 4-41 Device information retrieval ..................................4-47Maintenance .........................................................................4-48Procedure 4-42 Password configuration ........................................4-48Procedure 4-43 LOID configuration ..............................................4-49Procedure 4-44 SLID configuration ..............................................4-505 — ONT configuration file over OMCI 5-15.1 Purpose ................................................................................... 5-25.2 Supported configuration file types ................................................... 5-2Filename conventions ............................................................... 5-45.3 ONT configuration file over OMCI..................................................... 5-4Procedure 5-1 Configuring an ONT using a configuration file viaOMCI.............................................................................. 5-5R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
Contentsxxxviii Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideList of figuresFigure 1 PSE certification............................................................................ xiFigure 2 Laser product label .......................................................................xivFigure 3 Laser classification label .................................................................xivFigure 4 Laser warning labels ...................................................................... xvFigure 1 Products below MCV value label ...................................................... xviiiFigure 2 Products above MCV value label ........................................................xixFigure 3 Recycling/take back/disposal of product symbol ....................................xxiFigure 1 Sample safety label on the ONT equipment.......................................... xxvFigure 2 Sample laser product label showing CDRH 21 CFR compliance ..................xxviiFigure 3 Laser product label ....................................................................xxviiiFigure 4 Laser classification label ..............................................................xxviiiFigure 5 Laser warning labels .................................................................... xxixFigure 6 Sample laser product safety label on the ONT equipment......................... xxxFigure 1-1 G-240WZ-A indoor ONT physical connections...................................... 1-6Figure 1-2 G-240WZ-A indoor ONT LEDs ......................................................... 1-8Figure 1-3 Single-residence Wi-Fi ONT with Gigabit Ethernet and POTS andwithout RF video ................................................................1-13Figure 1-4 G-240WZ-A ONT hardware block ...................................................1-13Figure 2-1 G-240WZ-A indoor ONT connections and wall mounting key holes............. 2-4Figure 3-1 G-240WZ-A indoor ONT connections ................................................ 3-4Figure 4-1 Web login window ..................................................................... 4-3Figure 4-2 Device Information window .......................................................... 4-4Figure 4-3 LAN status window..................................................................... 4-5Figure 4-4 WAN status window.................................................................... 4-7Figure 4-5 WAN status IPv6 window.............................................................. 4-8Figure 4-6 Home networking information window............................................4-10Figure 4-7 Optics module status window.......................................................4-11Figure 4-8 Voice Information window...........................................................4-12Figure 4-9 LAN network window .................................................................4-13Figure 4-10 LAN IPv6 network window..........................................................4-14Figure 4-11 WAN network window...............................................................4-16Figure 4-12 WAN DHCP window ..................................................................4-17Figure 4-13 WiFi 2.4G network window ........................................................4-18Figure 4-14 WiFi 5G network window...........................................................4-20Figure 4-15 Routing network window ...........................................................4-21Figure 4-16 DNS network window................................................................4-22Figure 4-17 TR-069 network window............................................................4-23Figure 4-18 Firewall window .....................................................................4-24Figure 4-19 MAC filter window...................................................................4-25Figure 4-20 IP filter window......................................................................4-26Figure 4-21 DMZ and ALG window ...............................................................4-27Figure 4-22 Port forwarding window............................................................4-28Figure 4-23 DDNS window.........................................................................4-29Figure 4-24 NTP window ..........................................................................4-30Figure 4-25 USB storage window.................................................................4-31Figure 4-26 UPnP and DLNA window ............................................................4-32Figure 4-27 Password window....................................................................4-33Figure 4-28 SLID configuration window.........................................................4-34Figure 4-29 Device management window ......................................................4-35R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
ContentsAlcatel-Lucent 7368 ISAM ONT xxxixEdition 01G-240WZ-A Product GuideFigure 4-30 Backup and Restore window .......................................................4-36Figure 4-31 Firmware upgrade window.........................................................4-36Figure 4-32 Reboot window ......................................................................4-37Figure 4-33 Factory default window ............................................................4-38Figure 4-34 Diagnose window ....................................................................4-39Figure 4-35 Log window...........................................................................4-40Figure 4-36 RG Troubleshooting Counters window............................................4-41Figure 4-37 Smart Home window ................................................................4-43Figure 4-38 Web login window ...................................................................4-46Figure 4-39 Device Information window........................................................4-47Figure 4-40 Password window....................................................................4-48Figure 4-41 LOID configuration window ........................................................4-49Figure 4-42 SLID configuration window.........................................................4-50List of tablesTable 1 Safety labels ..................................................................................xTable 1 Safety labels .............................................................................. xxivTable 1-1 Identification of G-240WZ-A indoor ONTs ........................................... 1-2Table 1-2 G-240WZ-A indoor ONT interface connection capacity............................ 1-6Table 1-3 G-240WZ-A indoor ONT physical connections ....................................... 1-7Table 1-4 G-240WZ-A indoor ONT LEDs........................................................... 1-8Table 1-5 G-240WZ-A indoor ONT physical specifications..................................... 1-9Table 1-6 G-240WZ-A indoor ONT power consumption specifications......................1-10Table 1-7 G-240WZ-A indoor ONT environmental specifications ............................1-10Table 1-8 G-240WZ-A indoor ONT capacity for GEM ports and T-CONTs ...................1-10Table 1-9 Package P ONTs ONTENET performance monitoring statistics ..................1-11Table 1-10 Package P ONTs ONTL2UNI performance monitoring statistics ................1-11Table 1-11 Package P ONTs PONONTTC, PONONTMCTC, PONONTTCHSI,PONONTTCCES, PONONTTCFLOW, PONONTTCVOIP performancemonitoring statistics ............................................................1-12Table 1-12 Package P ONTs PONONTTC aggregate performance monitoringstatistics ..........................................................................1-12Table 1-13 G-240WZ-A ONT considerations and limitations..................................1-17Table 4-1 Device Information parameters ....................................................... 4-4Table 4-2 LAN status parameters.................................................................. 4-5Table 4-3 WAN status parameters................................................................. 4-7Table 4-4 WAN status IPv6 parameters........................................................... 4-9Table 4-5 Home networking parameters ........................................................4-10Table 4-6 Optics module status parameters....................................................4-11Table 4-7 Voice Information parameters........................................................4-12Table 4-8 LAN network parameters ..............................................................4-13Table 4-9 LAN IPv6 network parameters ........................................................4-15Table 4-10 WAN network parameters............................................................4-16Table 4-11 WAN DHCP parameters ...............................................................4-17Table 4-12 WiFi 2.4G network parameters .....................................................4-18Table 4-13 WiFi 5G network parameters........................................................4-20Table 4-14 Routing network parameters ........................................................4-21Table 4-15 DNS network parameters.............................................................4-22R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
Contentsxl Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideTable 4-16 TR-069 network parameters.........................................................4-23Table 4-17 Firewall parameters ..................................................................4-24Table 4-18 MAC filter parameters................................................................4-25Table 4-19 IP filter parameters...................................................................4-26Table 4-20 DMZ and ALG parameters ............................................................4-27Table 4-21 Port forwarding parameters.........................................................4-28Table 4-22 DDNS parameters......................................................................4-30Table 4-23 NTP parameters .......................................................................4-30Table 4-24 USB storage parameters..............................................................4-31Table 4-25 Password parameters.................................................................4-33Table 4-26 SLID configuration parameters......................................................4-34Table 4-27 Device management parameters ...................................................4-35Table 4-28 RG Troubleshooting Counters parameters.........................................4-41Table 4-29 Smart Home parameters .............................................................4-43Table 4-30 Device Information parameters.....................................................4-47Table 4-31 Password parameters.................................................................4-48Table 4-32 SLID configuration parameters......................................................4-50Table 5-1 Supported configuration files.......................................................... 5-3R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
Alcatel-Lucent 7368 ISAM ONT 1-1Edition 01G-240WZ-A Product Guide1 — G-240WZ-A unit data sheet1.1 G-240WZ-A part numbers and identification 1-21.2 G-240WZ-A general description 1-21.3 G-240WZ-A software and installation feature support 1-51.4 G-240WZ-A interfaces and interface capacity 1-61.5 G-240WZ-A LEDs 1-71.6 G-240WZ-A detailed specifications 1-91.7 G-240WZ-A GEM ports and T-CONTs 1-101.8 G-240WZ-A performance monitoring statistics 1-111.9 G-240WZ-A functional blocks 1-121.10 G-240WZ-A standards compliance 1-141.11 G-240WZ-A special considerations 1-16R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
1 — G-240WZ-A unit data sheet1-2 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product Guide1.1 G-240WZ-A part numbers and identificationTable 1-1 provides part numbers and identification information for the G-240WZ-A indoor ONT.Table 1-1 Identification of G-240WZ-A indoor ONTs1.2 G-240WZ-A general descriptionG-240WZ-A indoor ONTs provide the subscriber interface for the network by terminating the PON interface and converting it to user interfaces that directly connect to subscriber devices. The ONT is compatible with all existing subscriber equipment, including analog phones with both tone and rotary dial capabilities, cordless phones, modems, fax machines, and caller ID boxes (Type I, Type II, and Type III). G-240WZ-A ONTs contain integrated ZigBee and Z-Wave chip sets for use in wireless home automation systems. For information about configuring home automation files, see the section “Smart Home configuration” in the chapter “Configure a G-240WZ-A indoor ONT”.Mnemonic Ordering kit part number Provisioning number Description CLEI CPR ECI/Bar codeG-240WZ-A 3FE 45677 AA 3FE 45687 AA Package P 2 POTS ports, 4 10/100/1000 Base-T Ethernet interfaces, and 802.11b/g/n/ac Wi-Fi radio with on/off switch. For use in the US market.This ONT has 2 USB ports, 1 USB 3.0 and 1 USB 2.0.This ONT has integrated ZigBee and Z-Wave chip sets for use in wireless home automation systems.———3FE 45677 BA 3FE 45687 BA Package P 2 POTS ports, 4 10/100/1000 Base-T Ethernet interfaces, and 802.11b/g/n/ac Wi-Fi radio with on/off switch. For use in the European market.This ONT has 2 USB ports, 1 USB 3.0 and 1 USB 2.0.This ONT has integrated ZigBee and Z-Wave chip sets for use in wireless home automation systems.———3FE 45677 CA 3fE 45687 CA Package P 2 POTS ports, 4 10/100/1000 Base-T Ethernet interfaces, and 802.11b/g/n/ac Wi-Fi radio with on/off switch.For use in the Australian market.This ONT has 2 USB ports, 1 USB 3.0 and 1 USB 2.0.This ONT has integrated ZigBee and Z-Wave chip sets for use in wireless home automation systems.———R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
1 — G-240WZ-A unit data sheetAlcatel-Lucent 7368 ISAM ONT 1-3Edition 01G-240WZ-A Product GuideG-240WZ-A indoor ONTs provide the following functions:•Single fiber GPON interface with 1.244Gbit/s upstream and 2.488Gbit/s downstream data rates•Advanced data features such as VLAN tag manipulation, classification, and filtering.•Traffic classification and QoS capability•Analog Telephone Adapter (ATA) function integrated based on SIP (RFC3261) and H.248, with various CLASS services supported, including Caller ID, Call Waiting, Call Forwarding, and Call Transfer•5 REN per line•Multiple voice Codec•MDI/MDIX auto-negotiation•Line Rate L2 traffic•Internal Switch•UPnP IGD1.0 support•Bridged mode or routed mode per LAN port•Optics that support received signal strength indication (RSSI)•Internal DHCP server, with configurable DHCP pool and gateway•WPS on wireless authorization support•802.11ac support•2.4GHz/5GHz dual band concurrency, both with configurable Wi-Fi tx power from 100mw to 500mw, in 100mw increments.•Enhanced ONT; SSH-Telnet-FTP and http server are disabled from the WAN side•Concurrent 802.11n 3x3 MIMO in 2.4GHz and 802.11ac 4x4 MIMO in 5GHz•64/128 WEP encryption•WPA, WPA-PSK/TKIP•WPA2, WPA2-PSK/AES•support for multiple SSIDs (private and public instances); contact your ALU representative for further details.•WLAN on/off push button•WPS/PBC buttons (for 2.4G and 5G)•Ethernet-based Point-to-Point (PPPoE)•Network Address Translation (NAT)•Network Address Port Translation (NAPT)•ALG and UPnP port forwarding•DMZ•IP/MAC filter•Multi-level firewall•DNS server•DHCP client/server•support for HT40 mode for increased channel bandwidth•support for up to 32 simultaneous wireless connections•External USB HD (Hard Drive) support, accessible to all LAN devices•support for AIS with DOWN MEPR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
1 — G-240WZ-A unit data sheet1-4 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideConfiguring the G-240W-A to function as a single port ONTIn addition to functioning as a residential gateway, the G-240W-A ONT can be configured to function as a single port ONT.In the custom configuration, the ONT reports to the OLT as one PPTP port. The physical Ethernet port of the ONT is managed by the RGW using the TR-069 protocol, rather than by the ONT/OMCI.To enable the ONT to function as a single port ONT, the value of the parameter:InternetGatewayDevice.DeviceInfo.X_ALU-COM_PortReport2OLT.PPTPmust be set to PPTP_oneA custom pre-configuration file is required to operate the G-240W-A as a single-port ONT. Contact your Alcatel-Lucent support engineer to arrange for a custom pre-configuration file.TR-069 support for reading optical parametersThe ONT supports the reading of optical parameters via TR-069:•laser bias current•voltage•temperature•received signal levels•lower thresholdsThese are the same optical parameters supported in the GUI. For more information, see Table 4-6 in the chapter “Configure a G-240WZ-A indoor ONT”.TR-069 object support for WiFi parametersThe ONT supports the status retrieval and configuration of the following Wi-Fi parameters via TR-069:•channel•SSID•password for WPA and WEP•Tx power (transmission rate in dBm)These are the same TR-069 object parameters that are supported in the GUI. For more information, see Tables 4-2, 4-12, and 4-13 in the chapter “Configure a G-240WZ-A indoor ONT”.TR-104 parameter extension support for voice serviceA proprietary attribute has been added to the TR-104 Voice Service object structure to enable the ACS to configure the name of the embedded GSIP XML file to be selected.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
1 — G-240WZ-A unit data sheetAlcatel-Lucent 7368 ISAM ONT 1-5Edition 01G-240WZ-A Product GuideThe TR-104 Voice Service Object is: InternetGatewayDevice.Services.VoiceService.{i}.Capabilities.SIP.The proprietary attribute is: X_ALU-COM_XML_File_Name_Path.Mobile offload supportAs part of the E2E solution supported by the ISAM 7750 service router, the G-240WZ-A ONT offers Mobile Offload support using a combination of EAP-SIM and ITU-T 802.11.EAP-SIM is an authentication method that uses the user credentials on the SIM card and EAP to authenticate the user with the Wi-Fi network, removing the need for user input (username and password). A dedicated public mobile offload SSID in the ONT enables mobile subscribers to connect to the Internet. Encryption is supported by 802.11, providing seamless Wi-Fi authentication for SIM-based user equipment. The ONT acts as the RADIUS client and sends the encapsulated EAP messages to the AAA server via the WLAN Gateway, which acts as the RADIUS proxy server. The interaction between the ONT and the AAA server provides subscriber management for authenticated mobile users without adding authentication load to the 3G network.Bridged Residential Gateway (BRG) supportThe BRG receives IP addresses for the WAN interface using DHCP or PPPoE. The BRG can use either Ipv4 or Ipv6 addresses. BRG uses OpenFlow protocol version 1.3.1 to manage Access Control List entries and routing protocols. TR-069 can be used to manage the local DHCP server and the soft GRE tunnel.The BRG supports the encapsulation of Ethernet frames from different bridges in the GRE tunnel to the access tunnel. Multiple bridges can map to the same GRE tunnel. Where encapsulated packets exceed the MTU (packet size), fragmentation is also supported.Upstream QoS can reserve bandwidth for public and private Wi-Fi bridges, based on profiles defined for the access uplink speed. A unique VLAN tag can be configured for each SSID on the BRG. Unicast QoS adjustment can be enabled to support Multicast IPTV Liveness detection and redundancy, link failure notification, and DHCP local server fallback are provided to help manage potential problems with gateway access. Event notification via TR-069 reports when the PON link is up and the tunnel is unreachable.1.3 G-240WZ-A software and installation feature supportFor information on installing or replacing the G-240WZ-A see:•Install a G-240WZ-A indoor ONT•Replace a G-240WZ-A indoor ONTR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
1 — G-240WZ-A unit data sheet1-6 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideFor information on the following topics, see the 7368 ISAM ONT Product Overview Guide:•ONT and MDU general descriptions of features and functions•Ethernet interface specifications•POTS interface specifications•RSSI specifications•Wi-Fi specifications•ONT optical budget•SLID entry via Ethernet port•ONT management using an ONT interface1.4 G-240WZ-A interfaces and interface capacityTable 1-2 describes the supported interfaces and interface capacity for G-240WZ-A indoor ONTs.Table 1-2 G-240WZ-A indoor ONT interface connection capacityNote(1) The G-240WZ-A ONTs provide Wi-Fi service that is enabled and disabled using a Wi-Fi on/off switch. G-240WZ-A connections and componentsFigure 1-1 shows the physical connections for G-240WZ-A indoor ONTs, Figure 1-1 G-240WZ-A indoor ONT physical connectionsONT type and model Maximum capacityPOTS 10/ 100BASE-T10/ 100/ 1000 BASE-TRF video (CATV) MoCA VDSL2 E1/T1 Local craft GPONSC/APCG-240WZ-A (1) 2—4— ———— 125260USB2.0 TEL 1-2 LAN 1-4WPS 2.4G WLANWPS 5GPairingResetPowerON/OFFUPSUSB2.0 TEL1 TEL2 LAN1 LAN2 LAN3LAN4WPS 2.4G WLANWPS 5G PAIRING RESET POWER ON/OFF UPSR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
1 — G-240WZ-A unit data sheetAlcatel-Lucent 7368 ISAM ONT 1-7Edition 01G-240WZ-A Product GuideTable 1-3 describes the physical connections for G-240WZ-A indoor ONTs.Table 1-3 G-240WZ-A indoor ONT physical connectionsNote(1) The primary path for the earth ground for these ONTs is provided by the 12V Return signal in the power connector.1.5 G-240WZ-A LEDsFigure 1-2 shows the G-240WZ-A indoor ONT LEDs.Connection (1) DescriptionUSB ports This connection is provided through 2 USB ports, 1 USB 3.0 and 1 USB 2.0. The ONT supports external USB hard drives that can be made accessible to all LAN devices.POTS ports This connection is provided through RJ-11 ports. Up to two POTS connections are supported.The POTS ports support voice services. Ethernet ports This connection is provided through Ethernet RJ-45 connectors. Up to four 10/100/1000 Base-T Ethernet interfaces are supported.The Ethernet ports can support both data and in-band video services on all four interfaces.WPS buttons The Wi-Fi Protected Setup buttons are labeled WPS2.4G and WPS5G. These buttons enable and disable WLAN data encryption.Pairing button This button is used to enable or disable the pairing of devices.WLAN button Wi-Fi service is compliant with IEEE 802.11 standards and is enabled and disabled using the WLAN button. Reset button Pressing the Reset button for less than 10 seconds reboots the ONT; pressing the Reset button for 10 seconds resets the ONT to the factory defaults, except for the LOID and SLID.Power input This connection is provided through the power connector. A power cable fitted with a barrel connector is used to make the connection. On/Off button This button turns the ONT on or off. UPS input This connection is provided through a UPS connector. R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
1 — G-240WZ-A unit data sheet1-8 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideFigure 1-2 G-240WZ-A indoor ONT LEDsTable 1-4 provides LED descriptions for G-240WZ-A indoor ONTs.Table 1-4 G-240WZ-A indoor ONT LEDsPOWER BTR GPON AUTH LAN1 LAN2 LAN3LAN4 VOIP WPS 2.4G WPS 5G WLAN 2.4G WLAN 5G USB INTERNET ZIGBEE ZWAVE PAIRINGTEL2TEL1TEL 1-2LAN 1-4PA I R I N GZWAVEZIGBEEINTERNETUSBVOIPWLAN 5GWPS 5GWLAN 2.4GWPS 2.4GBTRGPONAUTH25261POWERIndicator LED color and behavior LED behavior descriptionPower Green solidRed solidOffPower onLight failed on startup (for example corrupt flash), or self test failed on startup, or self test failed during regular operation or when executed over OMCIPower offBTR OffGreenBattery alarm set or battery not provisioned (not affected by AC power failure)Battery charged; no battery alarmsLink Green solidOffGPON link between ONT and OLT is operating normallyGPON link is down or no link connectedAuth Green solidGreen flashingOffONT is authorizedONT is process of ranging or synchronizing on OMCIONT is not authorizedLAN 1 to 4 Green solidGreen flashingOffEthernet is linkedLAN activity is present (in either direction)ONT power is off or Ethernet is not connectedTEL 1 to 2 Green solidGreen flashingOffAt least one of the POTS lines has a telephone off hookAt least one of the POTS lines has a telephone in ‘call in’ or ‘talking’ conditionTelephones are all on hook(1 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
1 — G-240WZ-A unit data sheetAlcatel-Lucent 7368 ISAM ONT 1-9Edition 01G-240WZ-A Product Guide1.6 G-240WZ-A detailed specificationsTable 1-5 lists the physical specifications for G-240WZ-A indoor ONTs.Table 1-5 G-240WZ-A indoor ONT physical specificationsVOIP Green solidOffVOIP service is built up and can provide serviceVOIP service is not built up or out of serviceWPS2.4G and 5GGreen solidRedOffError and session overlap statusWPS is disabledWPS is enabledWLAN2.4G and 5GGreen solidGreen flashingOffWireless link is upTraffic activity on wireless linkWireless link is down or not connectedUSB Green solidGreen flashingOffAt least one device is connected to a USB portTraffic activity on at least on USB connectionNo device connected to a USB portINTERNET Green solid Green flashingOffHSI WAN is connected: a) the device has an IP address assigned from IPCP, DHCP, or static, and no traffic has been detected; b) the session is dropped due to idle timeout but the PON link is still present.PPPoE or DHCP connection in progressHSI WAN is not connected: a) there is no physical interface connection; b) the device is in bridged mode without an assigned IP address; c) the session has been dropped for reasons other than idle timeout.ZIGBEE Green solidGreen flashingOffRedZigBee is enabledZigBee traffic activityZigBee is disabledZigBee chip failureZwave Green solidGreen flashingOffRedZ-Wave is enabledZ-Wave traffic activityZ-Wave is disabledZ-Wave chip failurePAIRING Green solidGreen flashingOffZ-Wave is pairingZ-Wave pairing succeededZ-Wave is not pairingIndicator LED color and behavior LED behavior description(2 of 2)Description SpecificationLength 10.8 in. (275 mm)Width 7.6 in. (192 mm)Height 2.3 in. (59 mm)Weight [within ± 0.5 lb (0.23 kg)] 1.33 lb (0.61 kg)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
1 — G-240WZ-A unit data sheet1-10 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideTable 1-6 lists the power consumption specifications for G-240WZ-A indoor ONT.Table 1-6 G-240WZ-A indoor ONT power consumption specificationsTable 1-7 lists the environmental specifications for G-240WZ-A indoor ONT.Table 1-7 G-240WZ-A indoor ONT environmental specifications1.7 G-240WZ-A GEM ports and T-CONTsTable 1-8 lists the maximum number of supported T-CONTs and GEM ports. See the appropriate release Customer Release Notes for the most accurate list of supported devices.Table 1-8 G-240WZ-A indoor ONT capacity for GEM ports and T-CONTsMnemonic Maximum power (Not to exceed) Condition Minimum power ConditionG-240WZ-A (3FE 56525 AAAA)18.5 W 2 POTS off-hook, 4 10/100/1000 Base-T Ethernet, Wi-Fi operational8.9 W 2 POTS on-hook, other interfaces/services not provisionedMounting method Temperature range and humidity AltitudeOn desk or wall mounted Operating: 23°F to 113°F (-5°C to 45°C) ambient temperature5% to 85% relative humidity, non-condensingContact your Alcatel-Lucent technical support representative for more informationStorage: -4°F to 158°F (-20°C to 70C)ONT or MDU Maximum NotesPackage P ONTsGEM ports per indoor or outdoor ONT 124 124 are present; 122 are available, and 2 are reserved for multicast and debuggingT-CONTs per indoor or outdoor ONT 32 32 are present; 31 are available, and 1 is reserved for OMCIR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
1 — G-240WZ-A unit data sheetAlcatel-Lucent 7368 ISAM ONT 1-11Edition 01G-240WZ-A Product Guide1.8 G-240WZ-A performance monitoring statisticsThe following section identifies the supported performance monitoring statistics for G-240WZ-A ONTs. A check mark indicates the statistic is supported on that ONT. An empty cell indicates the statistic is not supported. The following tables are categorized by supported alarm types:•Table 1-9 provides statistics for ONTENET type counters•Table 1-10 provides statistics for ONTL2UNI type counters•Table 1-11 provides statistics for PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES, PONONTTCFLOW, and PONONTTCVOIP type counters•Table 1-12 provides statistics for PONONTTC aggregate type countersTable 1-9 Package P ONTs ONTENET performance monitoring statisticsNote(1) A 5 second polling window limitation exists on the ONT, therefore the margin of error for each 15-min window is 5 secondsTable 1-10 Package P ONTs ONTL2UNI performance monitoring statisticsNote(1) A 5 second polling window limitation exists on the ONT, therefore the margin of error for each 15-min window is 5 secondsNote — If you have trouble accessing G-240WZ-A ONTs performance monitoring statistics using TL1, please contact your Alcatel-Lucent support representative for more information about how to access and retrieve performance monitoring type counters.ONT ONTENET statisticsFCSEECLCRBOSCFMCFDTIMTECSEAEIMREFTLTBOSQEG-240WZ-A (1) ✓✓✓✓✓✓✓✓✓✓✓✓✓✓ONT ONTL2UNI statisticsFRAMESBYTESMCFRAMESDSDRPDFRMSUSDRPDFRMSUSFRAMESDSFRAMESUSBYTESDSBYTESUSMCFRAMESDSMCFRAMESG-240WZ-A(1)✓✓✓✓✓✓✓✓✓✓✓R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
1 — G-240WZ-A unit data sheet1-12 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideTable 1-11 Package P ONTs PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES, PONONTTCFLOW, PONONTTCVOIP performance monitoring statisticsNote(1) A 5 second polling window limitation exists on the ONT, therefore the margin of error for each 15-min window is 5 secondsTable 1-12 Package P ONTs PONONTTC aggregate performance monitoring statisticsNote(1) A 5 second polling window limitation exists on the ONT, therefore the margin of error for each 15-min window is 5 seconds1.9 G-240WZ-A functional blocksG-240WZ-A indoor ONTs are single-residence ONTs that support Wireless (Wi-Fi) service. Wi-Fi service on these ONTs is compliant with the IEEE 802.11 standard and enabled or disabled using a WLAN button. In addition to the Wi-Fi service, these ONTs transmit Ethernet packets to four RJ-45 Ethernet ports and voice traffic to two RJ-11 POTS ports. These ONTs also feature fiber optic, USB, and power connectors.Figure 1-3 shows the functional blocks for G-240WZ-A indoor ONT. ONT PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES, PONONTTCFLOW, PONONTTCVOIP statisticsTXBLOCKSTXFRAGSRXBLOCKSRXFRAGSLOSTFRAGSBADGEMHDRSG-240WZ-A (1) ✓✓✓✓✓ ONT PONONTTC (aggregate) statisticsTXBLOCKSTXFRAGSRXBLOCKSRXFRAGSLOSTFRAGSBADGEMHDRSG-240WZ-A (1) ✓✓✓✓✓ R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
1 — G-240WZ-A unit data sheetAlcatel-Lucent 7368 ISAM ONT 1-13Edition 01G-240WZ-A Product GuideFigure 1-3 Single-residence Wi-Fi ONT with Gigabit Ethernet and POTS and without RF videoONT SoC technology serves as the main hardware block for these ONTs; see Figure 1-4.Figure 1-4 G-240WZ-A ONT hardware blockDDRNANDUART2xRJ11FXS4xGEPCIePCIeUSB2.03x3,2.4G4x4,5GUSB3.0Flash+RAM25241802.11n MAC/PHYRGMIIuPD720202PCM/SPI GE GE GE GE GPIOGPON SOCSLICXFMRZigbeePHYZwavePHYOptical BOBGPONGE PHY802.11n MAC/PHY PA/LNAANTANTPA/LNAControlprocessorEthernetMACsEthernet ports GPONPOTS portsDSPGPONMACSoC19421SoC BridgeR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
1 — G-240WZ-A unit data sheet1-14 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideONT SoC technology consists of five key elements:•GPON MACThe Gigabit Passive Optical Network Media Access Control (GPON MAC) element on the SoC terminates the GPON interface using an optical diplexer. This interface supports GPON as described in G.984.3 (GPON TC Layer) ITU specification. •Ethernet MACThe SoC provides up to four GE MACs.•DSP interfaceThe Digital Signal Processor (DSP) provides voice processing for 2 POTS lines with 3-way calling. The DSP has a dedicated 64 kbyte instruction cache and shares a 32 kbyte data cache with the Control Processor. It provides up to 4 network processor cores, each at 800MHz. •Control ProcessorThe Control Processor features an integral memory management unit that supports a dedicated 64 kbyte instruction cache and shares a single 32 kbyte data cache with the DSP. The Control Processor and DSP also include a single channel Data Management Application (DMA) controller with a 4 kbyte read ahead low-latency Dynamic Random Access Memory (DRAM) access port. The processors typically run at 500 MHz. •Switch matrixThe Switch matrix provides an integrated data channel between the four GE MACs, the GPON MAC, the DSP, the control processor, and the other integrated elements such as flash memory, DRAM, and the local bus controller.These ONTs can also interact with additional hardware components to support functionality not provided by the SoC technology.1.10 G-240WZ-A standards complianceG-240WZ-A indoor ONTs are compliant with the following standards:•802.1p marking and VLAN based pbit is supported•G.711 support for FAX and modem connection•G.984 support GPON interface (framing)•G.984.2 support for Amd1, class B+•G.984.3 support for activation and password functions•G.984.3 support for AES with operator enable/disable on per port-ID level•G.984.3 support for FEC in both upstream and downstream directions•G.984.3 support for multicast using a single GEM Port-ID for all video traffic•G984.4 and G.983.2 support for OMCI v1 and v2 interface for ONT management and provisioning•TR-247 certification based on completion of BBF.247 certification programR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
1 — G-240WZ-A unit data sheetAlcatel-Lucent 7368 ISAM ONT 1-15Edition 01G-240WZ-A Product GuideEnergy-related products standby and off modes complianceHereby, Alcatel-Lucent declares that the G-240WZ-A ONTs are in compliance with the essential requirements and other relevant provisions of Directive 2009/125/EC together with Commission Regulation (EC) No 1275/2008 and Commission Regulation (EC) No 801/2013. The G-240WZ-A ONTS qualify as equipment with high network availability (HiNA) functionality. Since the main purpose of G-240WZ-A ONTs is to provide network functionality with HiNA 7 days /24 hours, the modes Off/Standby, Power Management, and Networked Standby are inappropriate.For information about the type and number of network ports, see “G-240WZ-A interfaces and interface capacity” in this chapter.For information about power consumption, see “G-240WZ-A detailed specifications” in this chapter.FCC statementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure StatementThis device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no-collocation statement. R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
1 — G-240WZ-A unit data sheet1-16 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1 this device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation. 1.11 G-240WZ-A special considerationsG-240WZ-A is a package P ONT.Wi-Fi serviceG-240WZ-A indoor ONTs feature Wi-Fi service as well as voice and data services. Wi-Fi is a wireless networking technology that uses radio waves to provide wireless HSI and network connections. This ONT complies with the IEEE 802.11 standards, which the Wi-Fi Alliance defines as the basis for Wi-Fi technology. Wi-Fi physical featuresG-240WZ-A indoor ONTs have the following physical features that assist in providing Wi-Fi service: •WLAN button for enabling and disabling Wi-Fi service •7 internal antennae, consisting of two groups: 3 for 2.4G and 4 for 5G•two Wi-Fi Protected Setup (WPS) push buttons (one each for 2.4G and 5G) for adding WPS-enabled wireless devicesWi-Fi standards and certificationsThe Wi-Fi service on G-240WZ-A indoor ONTs supports the following IEEE standards and Wi-Fi Alliance certifications:•compliant with IEEE 802.11 standards•certified for IEEE 802.11b/g/n standards •WPA support including WPA-PSK•certified for WPA2-Personal and WPA2-EnterpriseWi-Fi GUI featuresG-240WZ-A indoor ONTs have HTML-based Wi-Fi configuration GUIs. G-240WZ-A ONT considerations and limitationsTable 1-13 lists the considerations and limitations for Package P G-240WZ-A ONTs.Caution — Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
1 — G-240WZ-A unit data sheetAlcatel-Lucent 7368 ISAM ONT 1-17Edition 01G-240WZ-A Product GuideTable 1-13 G-240WZ-A ONT considerations and limitationsConsiderations and limitationsCall History Data collection (ONTCALLHST) is supported, except for the following parameters: RTP packets (discarded), far-end RTCP and RTCP-XR participation, RTCP average and peak round trip delay, MOS, average jitter, number of jitter-buffer over-runs and under runs.Some voice features are configurable on a per ONT basis, including Call Waiting, Call Hold, 3-Way Calling, and Call Transfer.The following voice features / GSIP parameters are configurable on a per-Client/ per-ONT basis (not per-Subscriber):•Enable Caller ID and Enable Caller Name ID•Digitmap and the associated Interdigit and Critical timers and Enter key parameters•Warmline timer is enabled per subscriber, but the warmline timer value is configured per ONT and must have a lower value than the Permanent time•Miscellaneous timers: Permanent, Timed-release, Reanswer, Error-tone, and CW-alert timers•Features / functions: Message waiting mode, WMWI refresh interval, DTMF volume level•Service Codes for the following features: CCW, Call Hold and WarmlineThe Molex interface is not operational.Due to chipset limitations, the USB 3.0 throughput is currently limited to about 10Mbps.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
1 — G-240WZ-A unit data sheet1-18 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
Alcatel-Lucent 7368 ISAM ONT 2-1Edition 01G-240WZ-A Product Guide2 — Install a G-240WZ-A indoor ONT2.1 Purpose 2-22.2 General 2-22.3 Prerequisites 2-22.4 Recommended tools 2-22.5 Safety information 2-32.6 Procedure 2-4R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
2 — Install a G-240WZ-A indoor ONT2-2 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product Guide2.1 PurposeThis chapter provides the steps to install a G-240WZ-A indoor ONT. 2.2 GeneralThe steps listed in this chapter describe mounting and cabling for G-240WZ-A indoor ONTs. 2.3 PrerequisitesYou need the following items before beginning the installation: •all required cables2.4 Recommended toolsYou need the following tools for the installation:•#2 Phillips screwdriver•1/4 in. (6 mm) flat blade screwdriver•wire strippers•fiber optic splicing tools•RJ-45 cable plug crimp tool•voltmeter or multimeter•optical power meter•drill and drill bits•paper clipR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
2 — Install a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 2-3Edition 01G-240WZ-A Product Guide2.5 Safety informationRead the following safety information before installing the unit. Danger 1 — Hazardous electrical voltages and currents can cause serious physical harm or death. Always use insulated tools and follow proper safety precautions when connecting or disconnecting power circuits. Danger 2 — Make sure all sources of power are turned off and have no live voltages present on feed lines or terminals. Use a voltmeter to measure for voltage before proceeding.Danger 3 — Always contact the local utility company before connecting the enclosure to the utilities.Warning — This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT.Caution — Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit.Note 1 — Observe the local and national laws and regulations that may be applicable to this installation.Note 2 — Observe the following:•The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. •The indoor ONT must be installed by qualified service personnel.•Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use.•See the detailed specifications in the G-240WZ-A unit data sheet for the temperature ranges for these ONTs. R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
2 — Install a G-240WZ-A indoor ONT2-4 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product Guide2.6 ProcedureUse this procedure to install a G-240WZ-A indoor ONT. 1Place the indoor ONT unit:aOn the flat surface, such as a desk or shelf; go to step 3.bOn a wall, go to step 2.2Mount the G-240WZ-A indoor ONT on a wall.The G-240WZ-A indoor ONT must be mounted in a horizontal position, as indicated by the wall mounting key holes on the bottom of the ONT. If possible, mount the ONT on a wall stud.iAttach the wall mount adapter bracket (shipped wit h the ONT) to the two wall mounting keyholes on the ONT.Figure 2-1 G-240WZ-A indoor ONT connections and wall mounting key holesii Attach the ONT to the wall.3Review the connection locations as shown in Figures 2-1.4Connect the Ethernet cables to the RJ-45 ports; see Figure 2-1 for the location of the RJ-45 ports.5Route the POTS cables directly to the RJ-11 ports as per local practices.The POTS port to the left is labeled TEL1 for Line 1 while the port on the right is labeled TEL2 for Line 2, as shown in Figure 2-1.6Connect the power cable to the power connector.Note — The G-240WZ-A cannot be stacked with another ONT or with other equipment. The ONT mounting requirements are:•allow a minimum 100 mm clearance above the top cover•allow a minimum 50 mm clearance from the side vents•do not place any heat source directly above the top cover or below the bottom cover25260USB2.0 TEL 1-2 LAN 1-4WPS 2.4G WLANWPS 5GPairingResetPowerON/OFFUPSUSB2.0 TEL1 TEL2 LAN1 LAN2 LAN3LAN4WPS 2.4G WLANWPS 5G PAIRING RESET POWER ON/OFF UPSR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
2 — Install a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 2-5Edition 01G-240WZ-A Product Guide7If applicable, install the power supply according to manufacturer specifications.8Power up the ONT unit by using the power switch.9If used, enable the Wi-Fi service.iLocate the WLAN button on the ONT; see Figure 2-1 for location of the WLAN button.ii Press the WLAN button to change the status of the Wi-Fi service.10 Verify the ONT LEDs, voltage status, and optical signal levels; see the 7368 Hardware and Cabling Installation Guide.11 Activate and test the services; see the 7368 Hardware and Cabling Installation Guide.12 If used, configure the SLID; see the 7368 ISAM ONT Configuration, Management, and Troubleshooting Guide.13 If necessary, reset the ONT.iLocate the Reset button on a G-240WZ-A indoor ONT as shown in Figure 2-1.ii Insert the end of a straightened paper clip or other narrow object into the hole in the Reset button to reset the ONT.14 STOP. This procedure is complete.Note — Observe the following:•Units must be powered by a Listed or CE approved and marked limited power source power supply with a minimum output rate of 12 V dc, 1.25 A.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
2 — Install a G-240WZ-A indoor ONT2-6 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
Alcatel-Lucent 7368 ISAM ONT 3-1Edition 01G-240WZ-A Product Guide3 — Replace a G-240WZ-A indoor ONT3.1 Purpose 3-23.2 General 3-23.3 Prerequisites 3-23.4 Recommended tools 3-23.5 Safety information 3-33.6 Procedure 3-4R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
3 — Replace a G-240WZ-A indoor ONT3-2 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product Guide3.1 PurposeThis chapter provides the steps to replace G-240WZ-A indoor ONTs. 3.2 GeneralThe steps listed in this chapter describe mounting and cabling for G-240WZ-A indoor ONTs. 3.3 PrerequisitesYou need the following items before beginning the installation: •all required cables3.4 Recommended toolsYou need the following tools for replacing the ONT:•#2 Phillips screwdriver•1/4 in. (6 mm) flat blade screwdriver•wire strippers•fiber optic splicing tools•RJ-45 cable plug crimp tool•voltmeter or multimeter•optical power meter•drill and drill bitsR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
3 — Replace a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 3-3Edition 01G-240WZ-A Product Guide3.5 Safety informationRead the following safety information before replacing the unit. Danger 1 — Hazardous electrical voltages and currents can cause serious physical harm or death. Always use insulated tools and follow proper safety precautions when connecting or disconnecting power circuits. Danger 2 — Make sure all sources of power are turned off and have no live voltages present on feed lines or terminals. Use a voltmeter to measure for voltage before proceeding.Danger 3 — Always contact the local utility company before connecting the enclosure to the utilities.Warning — This equipment is ESD sensitive. Proper ESD protections should be used when removing the fiber access cover of the indoor ONT.Caution — Keep indoor ONTs out of direct sunlight. Prolonged exposure to direct sunlight can damage the unit.Note 1 — Observe the local and national laws and regulations that may be applicable to this installation.Note 2 — Observe the following:•The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC. •The indoor ONT must be installed by qualified service personnel.•Indoor ONTs must be installed with cables that are suitably rated and listed for indoor use.•See the detailed specifications in the G-240WZ-A unit data sheet for the ONT temperature ranges for these ONTs. R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
3 — Replace a G-240WZ-A indoor ONT3-4 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product Guide3.6 ProcedureUse this procedure to replace a G-240WZ-A indoor ONT. 1Deactivate the ONT services at the P-OLT. If you are using the SLID feature, this step is not required. The ONT and the services can remain in service (IS).iUse the RTRV-ONT command to verify the ONT status and th associated services. Record the serial number or the SLID of the ONT displayed in the command output.Example:RTRV-ONT::ONT-1-1-1-1-1;ii If the ONT is in service, place the ONT in OOS state.Example:ED-ONT::ONT-1-1-1-1-1;2If used, disable the Wi-Fi service by pressing the WLAN button; see Figure 3-1 for the location of the WLAN button.Figure 3-1 G-240WZ-A indoor ONT connections3Power down the unit by using the on/off power switch.4Disconnect the POTS, Ethernet, and power cables from the ONT; see Figure 3-1 for the connector locations on the G-240WZ-A indoor ONT.25260USB2.0 TEL 1-2 LAN 1-4WPS 2.4G WLANWPS 5GPairingResetPowerON/OFFUPSUSB2.0 TEL1 TEL2 LAN1 LAN2 LAN3LAN4WPS 2.4G WLANWPS 5G PAIRING RESET POWER ON/OFF UPSR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
3 — Replace a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 3-5Edition 01G-240WZ-A Product Guide5Disconnect the fiber optic cables.iUnplug the fiber optic cable with SC/APC connector from the ONT; see Figure 3-1 for the location of the fiber optic port.ii Attach a fiber dust cover to the end of the SC/APC connector.6Replace the ONT with a new unit:aOn a flat surface, such as a desk, substitute the new ONT for the old ONT on a flat surface, horizontally resting on its four feet.bOn a wall.iRemove the old ONT from the wall.ii Attach the wall mount adapter bracket (shipped with the ONT) to the two wall mounting key holes on the new ONT.iii Attach the new ONT to the wall.7Connect the Ethernet cables directly to the RJ-45 ports; see Figure 3-1 for the location of the RJ-45 ports.8Connect the POTS cables directly to the RJ-11 ports as per local practices; see Figure 3-1 for the location of the RJ-11 ports.The RJ-11 port to the left is labeled TEL1 for Line 1 while the port on the right is labeled TEL2 for Line 2.9Connect the power cable to the power connector.10 If applicable, install the power supply according to manufacturer specifications.11 Power up the unit by using the power switch.12 If used, enable the Wi-Fi service by pressing the WLAN button; see Figure 3-1 for the location of the WLAN button.Danger — Fiber cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters.Note — Observe the following:•Units must be powered by a Listed or CE approved and marked limited power source power supply with a minimum output rate of 12 V dc, 1.25 A.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
3 — Replace a G-240WZ-A indoor ONT3-6 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product Guide13 If used, configure the SLID; see the 7368 ISAM ONT Configuration, Management, and Troubleshooting Guide for more information.14 Verify the ONT LEDs, voltage status, and optical signal levels; see the 7368 Hardware and Cabling Installation Guide.15 Activate and test the services; see the 7368 Hardware and Cabling Installation Guide.16 If necessary, reset the ONT.iLocate the Reset button on a G-240WZ-A indoor ONT as shown in Figure 3-1.ii Insert the end of a straightened paper clip or other narrow object into the hole in the Reset button to reset the ONT.17 STOP. This procedure is complete.Note — A new SLID or the old SLID may be used with the replacement ONT. If a new SLID is used, the new SLID must also be programmed at the P-OLT using TL1 or a network manager. If the old SLID is used, no changes need to be made at the P-OLT; see the operations and maintenance documentation for the OLT for more details. R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
Alcatel-Lucent 7368 ISAM ONT 4-1Edition 01G-240WZ-A Product Guide4 — Configure a G-240WZ-A indoor ONT4.1 General 4-24.2 HGU mode GUI configuration 4-24.3 SFU mode configuration 4-44R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-2 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product Guide4.1 GeneralPlease refer to the configuration information provided with your OLT for the software configuration procedure for a G-240WZ-A ONT.For HTTP configuration procedures, please refer to the 7368 ISAM ONT Configuration, Management, and Troubleshooting Guide.4.2 HGU mode GUI configurationUse the procedures below to use the web-based GUI for the G-240WZ-A in HGU mode. This mode is preset at delivery.A home gateway unit (HGU) is a home networking device, used as a gateway to connect devices in the home through fiber to the Internet. An HGU provides a variety of features for the home network including routing and firewall capability. By using the HGU, users can connect all smart equipment in their home, including personal computers, set-top boxes, mobile phones, and other consumer electronics devices, to the Internet.LoginUse the procedure below to login to the web-based GUI for the G-240WZ-A.Procedure 4-1 Login to web-based GUI1Open a web browser and enter the IP address of the ONT in the address bar.The login window appears. The default gateway IP address is http://192.168.1.254. You can connect to this IP address using your web browser after connecting your PC to one of Ethernet ports of the ONT. The static IP address of your PC must be in the same 192.168.1.x subnet as the ONT.2Enter your username and password in the Log in window, as shown in Figure 4-1.The default username and password are printed on the ONT. The default user name is userAdmin. The default superuser name is AdminGPON. Contact Alcatel-Lucent for the superuser password.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-3Edition 01G-240WZ-A Product GuideFigure 4-1 Web login window3Click Login. The Device Information screen appears.4STOP. This procedure is complete.Device and connection statusG-240WZ-A ONTs support the retrieval of a variety of device and connection information, including:•device information•LAN status•WAN status•WAN status IPv6•Home networking informationCaution — Pressing the Reset button for less than 10 seconds reboots the ONT; pressing the Reset button for 10 seconds resets the ONT to the factory defaults, except for the LOID and SLID.Note — If you forget the current username and password, press the reset button for 5 s and the default values for the username and password will be recovered at startup. Note — To help protect the security of your Internet connection, the application displays a pop-up reminder to change both the Wi-Fi password and the ONT password. To increase password security, use a minimum of 10 characters, consisting of a mix of numbers and upper and lower case letters.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-4 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product Guide•Optics module status•Voice informationProcedure 4-2 Device information retrieval1Select Status > Device Information from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-2.Figure 4-2 Device Information windowTable 4-1 describes the fields in the Device Information window.Table 4-1 Device Information parametersNote — Upon login, the GPON Home Gateway window displays the WAN status block on the bottom left part of each window. This block shows the WAN connection ID, the WAN status, and any WAN errors. This block is accurate upon login, but it is static; click the Refresh button to update the information.Field DescriptionDevice Name Name on the ONTVendor Name of the vendorSerial Number Serial number of the ONTHardware version Hardware version of the ONT(1 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-5Edition 01G-240WZ-A Product Guide2Click Refresh to update the displayed information. 3STOP. This procedure is complete.Procedure 4-3 LAN status retrieval1Select Status > LAN Status from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-3.Figure 4-3 LAN status windowTable 4-2 describes the fields in the LAN status window.Table 4-2 LAN status parametersBoot version Boot version of the ONTSoftware version Software version of the ONTChipset Chipset of the ONTLot Number Production date of the ONTDevice Running Time Amount of time the device has run since last reset in hours, minutes, and secondsField DescriptionWireless InformationWireless Status Indicates whether the wireless is on or offWireless Channel Wireless channel number(1 of 2)Field Description(2 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-6 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product Guide2Click Refresh to update the displayed information. 3STOP. This procedure is complete.SSID Name Name of each SSIDWireless Encryption Status Encryption type used on the wireless connectionWireless Rx Packets Number of packets received on the wireless connectionWireless Tx Packets Number of packets transmitted on the wireless connectionWireless Rx Bytes Number of bytes received on the wireless connectionWireless Tx Bytes Number of bytes transmitted on the wireless connectionPower Transmission (mW) Power of the wireless transmission, in mW Ethernet InformationEthernet Status Indicates whether the Ethernet connection is on or offEthernet IP Address IP address of the Ethernet connectionEthernet Subnet Mask Subnet Mask of the Ethernet connectionEthernet MAC Address MAC address of the Ethernet connectionEthernet Rx Packets Number of packets received on the Ethernet connectionEthernet Tx Packets Number of packets transmitted on the Ethernet connectionEthernet Rx Bytes Number of bytes received on the Ethernet connectionEthernet Tx Bytes Number of bytes transmitted on the Ethernet connectionField Description(2 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-7Edition 01G-240WZ-A Product GuideProcedure 4-4 WAN status retrieval1Select Status > WAN Status from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-4.Figure 4-4 WAN status windowTable 4-3 describes the fields in the WAN status window.Table 4-3 WAN status parametersField DescriptionWAN connection list Drop-down menu listing all WAN connections. The connection shown is the connection for which WAN status will be shown.Connection Mode Connection mode of the WAN connectionEnable/Disable Select this checkbox to enable the WAN connectionVLAN VLAN IDWAN Link Status Whether the WAN link is up or downPPPoE Concentrator Displays the PPPoE Access Concentrator (AC) nameThis field applies only if the Connection Mode is set to PPPoEBRAS Connection Status Whether the BRAS connection is connecting or disconnectedAuthentication Failure Reason for authentication failure: account disabled, account expired, password expired, authentication failureISP Failure Reason for ISP failure: disconnect, time out, server out of resourcesPPPoE Connection Failure Displays USER DISCONNECT when connection failure is due to user disconnect rather than ISP failurePON Link Status Whether the PON link is up or downTx Packets Number of packets transmitted on the WAN connectionRx Packets Number of packets received on the WAN connection(1 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-8 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product Guide2Click Refresh to update the displayed information. 3STOP. This procedure is complete.Procedure 4-5 WAN status IPv6 retrieval1Select Status > WAN Status IPv6 from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-5.Figure 4-5 WAN status IPv6 windowTable 4-4 describes the fields in the WAN status IPv6 window.Tx Dropped Number of packets dropped on the transmit WAN connectionRx Dropped Number of packets dropped on the receive WAN connectionErr Packets Number of errored packets on the WAN connectionField Description(2 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-9Edition 01G-240WZ-A Product GuideTable 4-4 WAN status IPv6 parameters2Click Refresh to update the displayed information. 3STOP. This procedure is complete.Field DescriptionWAN connection list Drop-down menu listing all WAN connections. The connection shown is the connection for which WAN status will be shown.Connection Mode Connection mode of the WAN connectionEnable/Disable Select this checkbox to enable the WAN connectionVLAN VLAN IDWAN Link Status Whether the WAN link is up or downIPv6 Address IPv6 address that identifies the device and its locationNetmask Network maskGateway Gateway addressPrimary DNS Primary Domain Name ServerSecond DNS Secondary Domain Name ServerPON Link Status Whether the PON link is up or downTx Packets Number of packets transmitted on the WAN connectionRx Packets Number of packets received on the WAN connectionTx Dropped Number of packets dropped on the transmit WAN connectionRx Dropped Number of packets dropped on the receive WAN connectionErr Packets Number of errored packets on the WAN connectionR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-10 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideProcedure 4-6 Home networking information retrieval1Select Status > Home Networking from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-6.Figure 4-6 Home networking information windowTable 4-5 describes the fields in the Home networking window.Table 4-5 Home networking parameters2Click Delete to delete a particular local device connection. 3Click Refresh to update the displayed information. 4STOP. This procedure is complete.Field DescriptionLocal InterfaceEthernet Table displays the number of Ethernet connections and their settingsWireless Table displays the number of wireless connections and their settingsWireless SettingsNetwork Name Name of the wireless networkAccess Point Hexadecimal address of the wireless access pointLocal DevicesTable entry Each entry indicates the status (active or inactive), connection type, device name, IP address, hardware address, and IP address allocation of each connected local device.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-11Edition 01G-240WZ-A Product GuideProcedure 4-7 Optics module status retrieval1Select Status > Optics Module Status from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-7.Figure 4-7 Optics module status windowTable 4-6 describes the fields in the Optics module status window.Table 4-6 Optics module status parameters2Click Refresh to update the displayed information. 3STOP. This procedure is complete.Field DescriptionLaser Bias Current (ONT ANI-ONT-Side Optical Measurements) Laser bias current, measured in uAOptics Module Voltage (ONT ANI-ONT-Side Optical Measurements) Optics module voltage, measured in VOptics Module Temperature (ONT ANI-ONT-Side Optical Measurements) Optics module temperature, measured in CRx Optics Signal Level at 1490 nm (ONT ANI-ONT-Side Optical Measurements) Received optics signal level at 1490 nm, measured in dBmTx Optics Signal Level at 1310 nm (ONT ANI-ONT-Side Optical Measurements) Transmitted optics signal level at 1310 nm, measured in dBmLower (ONT ANI-ONT-Side Optical Measurements-Optical Threshold) Lower optical threshold, measured in dBmUpper (ONT ANI-ONT-Side Optical Measurements-Optical Threshold) Upper optical threshold, measured in dBmR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-12 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideProcedure 4-8 Voice information retrieval1Select Status > Voice Information from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-8.Figure 4-8 Voice Information windowTable 4-7 describes the fields in the Voice Information window.Table 4-7 Voice Information parametersNote(1) This field is only visible at the adminGPON level; it is not visible at the userAdmin level.2Click Refresh to update the displayed information. 3STOP. This procedure is complete.Field DescriptionPOTS 1 Registration Status Status of POTS port 1: registered or unregisteredPOTS 2 Registration Status Status of POTS port 2: registered or unregisteredPOTS 1 Line State State of POTS line 1: IDLE, Off Hook, or On HookPOTS 2 Line State State of POTS line 2: IDLE, Off Hook, or On HookSoftswitch(1) Proxy IP address; blank if the line is not registeredTelephone line 1 phone number(1) Phone number configured for telephone line 1Telephone line 2 phone number(1) Phone number configured for telephone line 2R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-13Edition 01G-240WZ-A Product GuideNetwork configurationG-240WZ-A ONTs also support network configuration, including:•LAN•LAN IPv6•WAN•WiFi 2.4G •WiFi 5G •Routing•DNS•TR-069Procedure 4-9 LAN networking configuration1Select Network > LAN from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-9.Figure 4-9 LAN network windowTable 4-8 describes the fields in the LAN network window.Table 4-8 LAN network parametersField DescriptionPort Mode: All Port to L2 Mode Select this checkbox to set all ports to L2 modePort ModePort 1 - 4 Drop-down port mode for each port: Route mode or bridge modeIPv4 Address IP Address of the ONTSubnet Mask Subnet mask of the ONTDHCP enable Select this checkbox to enable DHCP(1 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-14 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product Guide2Select the mode for each port.3Click Save.4Enter the DHCP configuration information.5Click Save.6Bind a MAC address to the LAN by entering the MAC and IP addresses and then clicking Add. Repeat for all MAC addresses to be bound.7STOP. This procedure is complete.Procedure 4-10 LAN IPv6 networking configuration1Select Network > LAN_IPv6 from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-10.Figure 4-10 LAN IPv6 network windowTable 4-9 describes the fields in the LAN IPv6 network window.DHCP Start IP Address Starting DHCP IP addressDHCP End IP Address Ending DHCP IP addressDHCP Lease Time DHCP lease time (in min)Bind MAC Address MAC address to associate to the LANBind IP Address IP address to associate to the bound MAC addressField Description(2 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-15Edition 01G-240WZ-A Product GuideTable 4-9 LAN IPv6 network parameters2Choose a DNS server, prefix config, and interface.3Select or enter the DHCP configuration information.4Enter the maximum and minimum intervals for RA messages.5Click Save/Apply.6STOP. This procedure is complete.Field DescriptionDNS Server Choose a DNS server from the drop-down menu.prefix config Choose a prefix config option from the drop-down menu, either WANConnection (prefix will be obtained from the WAN) or Static (enables you to enter the prefix).prefix This field appears if you selected the “Static” option for the “prefix config” field. Type a connection.Interface This field appears if you selected the Wan Connection option for the “prefix config” field. Choose a WAN connection interface from the drop-down menu.DHCP Start IP Address Enter the starting DHCP IP address.DHCP End IP Address Enter the ending DHCP IP address.Whether the address info through DCHPSelect this checkbox to enable address information retrieval through DHCP.Whether other info obtained through DHCPSelect this checkbox to enable retrieval of other information through DHCP.Maximum interval for periodic RA messagesEnter the maximum interval (in seconds) for periodic Router Advertisement messages. The interval range is from 4 to 1800.Minimum interval for periodic RA messagesEnter the minimum interval (in seconds) for periodic Router Advertisement messages. The interval range is from 4 to 1800.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-16 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideProcedure 4-11 WAN networking configuration1Select Network > WAN from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-11.Figure 4-11 WAN network windowTable 4-10 describes the fields in the WAN network window.Table 4-10 WAN network parametersField DescriptionWAN Connection List Choose a WAN connection from the drop-down menu to set the connection parametersConnection Type Select a connection type: IPoE or PPPoEIP Mode Choose an IP mode from the drop-down menu: IPv4 or IPv6Enable/Disable Select this checkbox to enable the WAN connectionNAT Select this checkbox to enable NATService Select the checkboxes to enable service types for this connectionEnable VLAN Select this checkbox to enable VLANVLAN ID Enter the VLAN IDVLAN PRI Enter the VLAN PRIWAN IP Mode Choose an IP mode from the drop-down menu(1 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-17Edition 01G-240WZ-A Product Guide2Configure a specific WAN connection.3Click Save.4STOP. This procedure is complete.Procedure 4-12 WAN DHCP configuration1Select Network > WAN DHCP from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-12.Figure 4-12 WAN DHCP windowTable 4-11 describes the fields in the WAN DHCP window.Table 4-11 WAN DHCP parametersConnection Type Choose a connection type from the drop-down menuUsername Enter the usernamePassword Enter the passwordKeep Alive Time Enter the Keep Alive Time (from 5 to 60 seconds)Field DescriptionWAN Connection List Choose a WAN connection from the drop-down menu Enable DHCP Option 60 Select this checkbox to enable DHCP Option 60 (vendor class identifier)(1 of 2)Field Description(2 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-18 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product Guide2Configure a WAN DHCP option.3Click Save.4STOP. This procedure is complete.Procedure 4-13 WiFi 2.4G networking configuration1Select Network > WiFi 2.4G from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-13.Figure 4-13 WiFi 2.4G network windowTable 4-12 describes the fields in the WiFi 2.4G network window.Table 4-12 WiFi 2.4G network parametersEnable DHCP Option 61 Select this checkbox to enable DHCP Option 61 (client identifier)Field Description(2 of 2)Field DescriptionEnable Select this checkbox to enable WiFi(1 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-19Edition 01G-240WZ-A Product Guide2Configure the WiFi connection.3If you have enabled and configured WPS, click WPS connect.4Click Save.5STOP. This procedure is complete.Mode Choose a Wi-Fi mode from the drop-down menu:•auto (b/g/n)•b•g•n•b/gChannel Choose a channel from the drop-down menu or choose Auto to have the channel automatically assignedBandwidth Choose 20 MHz or 40 MHz from the drop-down menu.Transmitting Power Choose the percentage transmitting power from the drop-down menuSSID Select Choose the SSID from the drop-down menuSSID Name Enter the SSID nameEnable SSID Enable or disable SSID from this drop-down menuSSID Broadcast Enable or disable SSID broadcast from this drop-down menuPort Mode Choose a port mode from the drop-down menu:•Route•BridgeEncrypt Mode Choose an encryption mode from the drop-down menu:•OPEN•WEP•WPA/WPA2 Personal•WPA/WPA2 EnterpriseWPA Version Choose a WPA version from the drop-down menu:•WPA1•WPA2•WPA1/WPA2WPA Encryption Mode Choose a WPA encryption mode from the drop-down menu:•TKIP•AES•TKIP/AESWPA Key Enter the WPA keyEnable WPS Enable or disable WPS from this drop-down menuWPS Mode Select a WPS mode from the drop-down menu: PBC (Push Button Connect) or PIN (Personal Identification Number)Field Description(2 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-20 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideProcedure 4-14 WiFi 5G networking configuration1Select Network > WiFi 5G from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-14.Figure 4-14 WiFi 5G network windowTable 4-13 describes the fields in the WiFi 5G network window.Table 4-13 WiFi 5G network parametersField DescriptionEnable Select this checkbox to enable WiFiChannel Choose a channel from the drop-down menu or choose Auto to have the channel automatically assignedBandwidth Choose 20 MHz or 40 MHz from the drop-down menuTransmitting Power Choose the percentage transmitting power from the drop-down menuSSID Select Choose the SSID from the drop-down menuSSID Name Enter the SSID nameEnable SSID Enable or disable SSID from this drop-down menuSSID Broadcast Enable or disable SSID broadcast from this drop-down menuEncrypt Mode Choose an encryption mode from the drop-down menu:•OPEN•WEP•WPA/WPA2 Personal•WPA/WPA2 EnterpriseWPA Key Enter the WPA keyEnable WPS Enable or disable WPS from this drop-down menu(1 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-21Edition 01G-240WZ-A Product Guide2Configure the WiFi connection.3If you have enabled and configured WPS, click WPS connect.4Click Save.5STOP. This procedure is complete.Procedure 4-15 Routing configuration1Select Network > Routing from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-15.Figure 4-15 Routing network windowTable 4-14 describes the fields in the Routing network window.Table 4-14 Routing network parametersWPS Mode Select a WPS mode from the drop-down menu: PBC (Push Button Connect) or PIN (Personal Identification Number)Field DescriptionEnable Routing Select this checkbox to enable routingDestination IP Address Enter the destination IP addressDestination Netmask Enter the destination network maskGateway Enter the gateway address(1 of 2)Field Description(2 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-22 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product Guide2Enter the routing information.3Click Add.4STOP. This procedure is complete.Procedure 4-16 DNS configuration1Select Network > DNS from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-16.Figure 4-16 DNS network windowTable 4-15 describes the fields in the DNS network window.Table 4-15 DNS network parameters2Enter the domain name and IP address and click Add.IPv4 Interface Choose a WAN connection previously created in the WAN network window from the drop-down menuField DescriptionDomain Name Domain nameIPv4 Address Domain IP addressOrigin Domain Origin domain nameNew Domain New domain nameField Description(2 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-23Edition 01G-240WZ-A Product Guide3If required, associate an origin domain with a new domain, click Add.4STOP. This procedure is complete.Procedure 4-17 TR-069 configuration1Select Network > TR-069 from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-17.Figure 4-17 TR-069 network windowTable 4-16 describes the fields in the TR-069 network window.Table 4-16 TR-069 network parameters2Configure TR-069 by entering the required information.Field DescriptionPeriodic Inform Enable Select this checkbox to enable periodic inform updatesPeriodic Inform Interval(s) Time between periodic inform updates, in secondsURL URL of the auto-configuration serverUsername Username used to log in to the ONTPassword Password used to log in to the ONTConnect Request Username Username used to log in to the auto-configuration serverConnect Request Password Password used to log in to the auto-configuration serverR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-24 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product Guide3Click Save.4STOP. This procedure is complete.Security configurationG-240WZ-A ONT also supports security configuration, including:•firewall•MAC filter•IP filter•DMZ and ALGProcedure 4-18 Firewall configuration1Select Security > Firewall from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-18.Figure 4-18 Firewall windowTable 4-17 describes the fields in the firewall window.Table 4-17 Firewall parameters2Configure the firewall.Field DescriptionSecurity level Choose the security level from the drop-down menuAttack Protect Enable or disable attack protect from the drop-down menuR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-25Edition 01G-240WZ-A Product Guide3Click Save.4STOP. This procedure is complete.Procedure 4-19 MAC filter configuration1Select Security > Mac Filter from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-19.Figure 4-19 MAC filter windowTable 4-18 describes the fields in the MAC filter window.Table 4-18 MAC filter parameters2Click Refresh to update the information.3Configure a MAC filter.4Click Add.5STOP. This procedure is complete.Field DescriptionEnable MAC filter Select this checkbox to enable the MAC filterMac Address Select a MAC address from the drop-down menu or enter the address in the text fieldMac Filter Mode Choose the MAC filter mode from this drop-down menu: Blocked or AllowedR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-26 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideProcedure 4-20 IP filter configuration1Select Security > IP filter from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-20.Figure 4-20 IP filter windowTable 4-19 describes the fields in the IP filter window.Table 4-19 IP filter parameters2Configure the IP filter. Field DescriptionEnable IP Filter Select this checkbox to enable an IP filterMode Choose an IP filter mode from the drop-down menu:•Drop for upstream•Drop for downstreamInternal Client Choose an internal client from the drop-down menu:•Customer setting - uses the IP address input below•IP - uses the connecting devices' IP to the ONTLocal IP Address Local IP addressSource Subnet Mask Source subnet maskRemote IP Address Remote IP addressDestination Subnet Mask Destination subnet maskProtocol Choose an application protocol or all from the drop-down menuR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-27Edition 01G-240WZ-A Product Guide3Click Add.4STOP. This procedure is complete.Procedure 4-21 DMZ and ALG configuration1Select Security > DMZ and ALG from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-21.Figure 4-21 DMZ and ALG windowTable 4-20 describes the fields in the DMZ and ALG window.Table 4-20 DMZ and ALG parameters2Configure ALG.3Click Save ALG.4Configure DMZ.Field DescriptionALG Config Select the checkboxes to enable the protocols to be supported by the ALG: FTP, TFTP, SIP, H323, RTSP, L2TP, IPSEC, PPTPDMZ ConfigWAN Connection List Choose a WAN connection from the drop-down menuEnable DMZ Select this checkbox to enable DMZ on the chosen WAN connectionDMZ IP Address Choose Customer Setting and enter the DMZ IP address or choose the IP address of a connected device from the drop-down menuR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-28 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product Guide5Click Save DMZ.6STOP. This procedure is complete.Application configurationG-240WZ-A ONT also supports application configuration, including:•port forwarding•DDNS•NTP•USB storage•UPnP and DLNAProcedure 4-22 Port forwarding configuration1Select Application > Port forwarding from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-22.Figure 4-22 Port forwarding windowTable 4-21 describes the fields in the port forwarding window.Table 4-21 Port forwarding parametersField DescriptionAPPName Choose an application name from the drop-down menuWAN Port WAN port rangeLAN Port LAN port range(1 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-29Edition 01G-240WZ-A Product Guide2Configure port forwarding.3Click Add.4STOP. This procedure is complete.Procedure 4-23 DDNS configuration1Select Application > DDNS from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-23.Figure 4-23 DDNS windowTable 4-22 describes the fields in the DDNS window.Internal Client Choose a connected device from the drop-down menu and enter the associated IP addressProtocol Choose the port forwarding protocol from the drop-down menu:•TCP•UDP•TCP/UDPEnable Mapping Select this checkbox to enable mappingWAN Connection List Choose a WAN connection from the drop-down menuNote: only active devices are shown on this menuField Description(2 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-30 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideTable 4-22 DDNS parameters2Configure DDNS.3Click Save.4STOP. This procedure is complete.Procedure 4-24 NTP configuration1Select Application > NTP from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-24.Figure 4-24 NTP windowTable 4-23 describes the fields in the NTP window.Table 4-23 NTP parametersField DescriptionWAN Connection List Choose a WAN connection from the drop-down menuEnable DDNS Select this checkbox to enable DDNS on the chosen WAN connectionISP Choose an ISP from the drop-down menu. Domain Name Domain nameUsername UsernamePassword PasswordField DescriptionEnable NTP Service Select this checkbox to enable NTP service(1 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-31Edition 01G-240WZ-A Product Guide2Configure NTP. 3Click Save.4STOP. This procedure is complete.Procedure 4-25 USB storage configuration1Select Application > USB storage from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-25.Figure 4-25 USB storage windowTable 4-24 describes the fields in the USB storage window.Table 4-24 USB storage parametersCurrent Time Enter the current local date and timeFirst Time Server Choose a time server from the drop-down menu or choose Customer setting and enter the address of the time server.Second Time Server Choose a time server from the drop-down menu or choose Customer setting and enter the address of the time server.Interval Time Interval at which to get the time from the time server, in secondsTime Zone Choose the local time zone from the drop-down menuField DescriptionEnable FTP server Select this checkbox to enable using an FTP server for data storage(1 of 2)Field Description(2 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-32 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product Guide2Configure USB storage.3Click Save.4STOP. This procedure is complete.Procedure 4-26 UPnP and DLNA configuration1Select Application > UPnP and DLNA from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-26.Figure 4-26 UPnP and DLNA window2Select the Enable UPnP checkbox to enable UPnP.3Click Save/Apply.4STOP. This procedure is complete.MaintenanceG-240WZ-A ONT also supports maintenance tasks, including:•password change•SLID configuration•device management•backup and restoreUsername Username for FTP serverPassword Password for FTP serverRe-enter Password Password for FTP serverField Description(2 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-33Edition 01G-240WZ-A Product Guide•firmware upgrade•device reboot•restore factory defaults•diagnose•logProcedure 4-27 Password configuration1Select Maintain > Password from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-27.Figure 4-27 Password windowTable 4-25 describes the fields in the password window.Table 4-25 Password parameters2Configure the new password.3Click Save.4STOP. This procedure is complete.Field DescriptionNew Password New passwordRe-enter password Password must match password entered abovePrompt message Password prompt messageR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-34 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideProcedure 4-28 SLID configuration1Select Maintain > SLID Configuration from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-28.Figure 4-28 SLID configuration windowTable 4-26 describes the fields in the SLID configuration window.Table 4-26 SLID configuration parameters2Configure the new SLID.3Click Save.4STOP. This procedure is complete.Field DescriptionCurrent SLID Displays current SLIDInput new SLID Enter new SLIDSLID Mode Choose a SLID mode from the drop-down menu. R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-35Edition 01G-240WZ-A Product GuideProcedure 4-29 Device management1Select Maintain > Device Management from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-29.Figure 4-29 Device management windowTable 4-27 describes the fields in the Device management window.Table 4-27 Device management parameters2Configure an alias for a specific host. 3Click Add.4STOP. This procedure is complete.Field DescriptionHost name Choose a host from the drop-down menuAlias Enter an alias for the chosen hostR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-36 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideProcedure 4-30 Backup and restore1Select Maintain > Backup and Restore from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-30. Figure 4-30 Backup and Restore window2Click Select File and choose the backup file.3Click Import Config File to restore the ONT to the saved backup or click Export Config File to export the current ONT configuration to the backup file.4STOP. This procedure is complete.Procedure 4-31 Upgrade firmware1Select Maintain > Firmware Upgrade from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-31. Figure 4-31 Firmware upgrade window2Click Select File and choose the firmware file.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-37Edition 01G-240WZ-A Product Guide3Click Upgrade to upgrade the firmware.4STOP. This procedure is complete.Procedure 4-32 Reboot ONT1Select Maintain > Reboot Device from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-32. Figure 4-32 Reboot window2Click Reboot to reboot the ONT.3STOP. This procedure is complete.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-38 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideProcedure 4-33 Restore factory defaults1Select Maintain > Factory Default from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-33. Figure 4-33 Factory default window2Click Factory Default to reset the ONT to its factory default settings.3STOP. This procedure is complete.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-39Edition 01G-240WZ-A Product GuideProcedure 4-34 Diagnose connections1Select Maintain > Diagnose from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-34. Figure 4-34 Diagnose window2Choose a WAN connection to diagnose from the drop-down menu.3Enter the IP address or domain name.4Select the test type: ping, traceroute, or both.5Enter the number of ping attempts to perform (1 - 1000); the default is 4.6Enter a ping packet length (64-1024); the default is 64.7Enter the maximum number of trace hops (1-255); the default is 30.8Click Start Test. Results will be displayed at the bottom of the window.9Click Cancel to cancel the test.10 STOP. This procedure is complete.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-40 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideProcedure 4-35 View log files1Select Maintain > Log from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-35. Figure 4-35 Log window2Choose a write level from the drop-down menu to determine which types of events are recorded in the log file:•Emergency•Alert•Critical•Error•Warning•Notice•Informational•Debug3Choose a reading level from the drop-down menu to determine which types of events to display from the log file:•Emergency•Alert•Critical•Error•Warning•Notice•Informational•DebugR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-41Edition 01G-240WZ-A Product Guide4The log file is displayed at the bottom of the window.5STOP. This procedure is complete.RG troubleshooting countersThe Troubleshooting Counters feature enables service providers and end users to monitor the performance of their broadband connection.Tests are run to retrieve upstream and downstream throughput, latency, and DNS response time. The Troubleshooting Counters window also displays upstream and downstream packet loss and Internet status.Procedure 4-36 Retrieve Residential Gateway (RG) troubleshooting counters1Select RG Troubleshooting Counters from the left menu in the GPON Home Gateway window.The RG Troubleshooting Counters window appears; see Figure 4-36. Figure 4-36 RG Troubleshooting Counters windowTable 4-28 describes the fields in the RG Troubleshooting Counters window.Table 4-28 RG Troubleshooting Counters parametersField DescriptionWAN Connection List Select a WAN connection from the listUS Throughput This test is used to determine the upstream throughput/speedClick US Speed Test to specify the time for the upstream testThe default is weekly, performed at idle to a public server(1 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-42 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product Guide2Configure the test times if desired.3Click Refresh to update the data. 4STOP. This procedure is complete.Smart Home configurationThe Smart Home feature is used to manage the devices for home monitoring systems.Both Zwave and Zigbee are supported.Procedure 4-37 Configure home monitoring systems1Select Smart Home from the left menu in the GPON Home Gateway window.The Smart Home window appears; see Figure 4-37. DS Throughput This test is used to determine the downstream throughput/speedClick DS Speed Test to specify the time for the downstream testThe default is weekly, performed at idle to a public serverUS Packet Loss The number of upstream packages lostDS Packet Loss The number of downstream packages lostInternet Status Whether the broadband connections is active (UP) or not (DOWN)Latency This test is used to determine the lowest round-trip time in milliseconds by pinging the target server multiple timesClick Latency Test to specify the time for the testThe default is weekly, performed at idle to a public serverDNS Response Time This test is used to determine the lowest round-trip time in milliseconds by sending a request to the target DNS serverClick DNS Response Test to specify the time for the testThe default is weekly, performed at idle to a public serverField Description(2 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-43Edition 01G-240WZ-A Product GuideFigure 4-37 Smart Home windowTable 4-28 describes the fields in the RG Troubleshooting Counters window.Table 4-29 Smart Home parameters2Configure the Smart Home files.3Click Factory Default to reset the values to the factory defaults. 4STOP. This procedure is complete.Field DescriptionBackup and RestoreSelect File Select a file from the drop down menu.Import Config File Click Import to import the configuration file.Export Config File Click Export to export the configuration file.Firmware UpgradeSelect File Select a file from the drop-down menu.Upgrade Click Upgrade to upgrade the firmware.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-44 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product Guide4.3 SFU mode configurationHGU is the default mode for the G-240WZ-A ONT, but you can use SFU mode to view device status information, change the password, authenticate the LOID, and change the SLID.Switch from default HGU mode to SFU modeTo switch from the default HGU mode to using SFU mode, use the procedure below.Procedure 4-38 Switching to SFU mode1Power up the G-240WZ-A ONT.2Change the Operator ID (OPID) to the applicable number to enable the ONT to switch to SFU mode, as described in “Modifying the operator ID”.3Download the SFU image to the ONT.4Reboot the ONT.5STOP. This procedure is complete.Procedure 4-39 Modifying the operator ID1Register the ONT with the OLT.2Check the original OPID.3Update the OntConfig.xml file by adding-the following content:<OperatorObject version=”1.0”><OperatorID=”XXXX”></OperatorObject>where: xxxx is the correct operator ID, for example ALCL for HGU mode, or XXXX for SFU mode.4Use a TFTP client tool to transfer the OntConfi.xml file to the OLT’s ONT directory and change the filename to the software version number, for example, 3FE123456789.xml.5Use a TL1 command to configure ONUSWCRTL:ENT-ONTSWCTRL::1::::HWVER=hwver,VARNT=,PLNDSWVER=UNPLANNED, PLNDSWVERCONF=UNPLANNED,DLDSWVER=swver;where:hwver is the EQPTVERNUM, for example EQPTVERNUM=3FE54945ABAA.swver is the software version number used as the filename in step 2, for example 3FE123456789.xml.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-45Edition 01G-240WZ-A Product Guide6Download the .xml file to update the operator ID:ED-ONT::ONT-1/1/3/1/19::::DLSW=AUTO;7Restart the ONT, then connect to the LAN and access the web-based GUI to check the operator ID default setting.8Use a TL1 command to disable further downloads:ED-ONT::ONT-1/1/3/1/19::::DLSW=DISABLED;9STOP. This procedure is complete.LoginUse the procedure below to login to the web-based GUI for the G-240WZ-A.Procedure 4-40 Login to web-based GUI1Open a web browser and enter the IP address of the ONT in the address bar.The login window appears. The default gateway IP address is http://192.168.1.254. You can connect to this IP address using your web browser after connecting your PC to one of Ethernet ports of the ONT. The static IP address of your PC must be in the same subnet as the ONT.2Enter your username and password in the Log in window, as shown in Figure 4-38.The default username and password are printed on the ONT. The default superuser username is adminGPON. Contact Alcatel-Lucent for the superuser password.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-46 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideFigure 4-38 Web login window3Click Login. 4STOP. This procedure is complete.Device and connection statusG-240WZ-A ONTs support the retrieval of a variety of device information.Caution — Pressing the Reset button for less than 10 seconds reboots the ONT; pressing the Reset button for 10 seconds resets the ONT to the factory defaults, except for the LOID and SLID.Note — If you forget the current username and password, press the reset button for 5 s and the default values for the username and password will be recovered at startup. R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-47Edition 01G-240WZ-A Product GuideProcedure 4-41 Device information retrieval1Select Status > Device Information from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-39.Figure 4-39 Device Information windowTable 4-30 describes the fields in the Device Information window.Table 4-30 Device Information parameters2Click Refresh to update the displayed information. 3STOP. This procedure is complete.Field DescriptionDevice Name Name on the ONTVendor Name of the vendorSerial Number Serial number of the ONTHardware version Hardware version of the ONTBoot version Boot version of the ONTSoftware version Software version of the ONTChipset Chipset of the ONTDevice Running Time Amount of time the device has run since last reset in hours, minutes, and secondsR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-48 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideMaintenanceG-240WZ-A ONT also supports maintenance tasks, including:•password change•LOID configuration•SLID configurationProcedure 4-42 Password configuration1Select Maintain > Password from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-40.Figure 4-40 Password windowTable 4-31 describes the fields in the password window.Table 4-31 Password parameters2Configure the new password.3Click Save.4STOP. This procedure is complete.Field DescriptionNew Password New passwordRe-enter password Password must match password entered abovePrompt message Password prompt messageR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONTAlcatel-Lucent 7368 ISAM ONT 4-49Edition 01G-240WZ-A Product GuideProcedure 4-43 LOID configuration1Select Maintain > LOID Config from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-41.Figure 4-41 LOID configuration window2Enter the LOID.3Enter the password, if applicable. 4Click Save/Apply.5STOP. This procedure is complete.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
4 — Configure a G-240WZ-A indoor ONT4-50 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideProcedure 4-44 SLID configuration1Select Maintain > SLID Configuration from the top-level menu in the GPON Home Gateway window, as shown in Figure 4-42.Figure 4-42 SLID configuration windowTable 4-32 describes the fields in the SLID configuration window.Table 4-32 SLID configuration parameters2Configure the new SLID.3Click Save.4STOP. This procedure is complete.Field DescriptionCurrent SLID Displays current SLIDInput new SLID Enter new SLIDSLID Mode Choose a SLID mode from the drop-down menu. R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
Alcatel-Lucent 7368 ISAM ONT 5-1Edition 01G-240WZ-A Product Guide5 — ONT configuration file over OMCI5.1 Purpose 5-25.2 Supported configuration file types 5-25.3 ONT configuration file over OMCI 5-4R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
5 — ONT configuration file over OMCI5-2 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product Guide5.1 PurposeThis procedure describes how to use configuration files over OMCI to configure ONTs. Some advantages include:•flexibility to change the ONT default behavior by downloading configuration file•flexibility to update a deployed ONT by downloading updated parameters•ability to securely download any configuration file to an ONT•ability to avoid using embedded configuration files in ONT software5.2 Supported configuration file typesTable 5-1 describes the configuration file types that are supported from 7368 ISAM ONT R05.02.00 and later. Note — This feature is supported for use with 7360 ISAM FX only; it is not supported for use with 7342 ISAM FTTU.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
5 — ONT configuration file over OMCIAlcatel-Lucent 7368 ISAM ONT 5-3Edition 01G-240WZ-A Product GuideTable 5-1 Supported configuration filesFile Index Description Details Supported ONTs/DPUPRE ONT pre-configuration fileThe XML-based PRECONFIG file controls the working mechanics of the ONT for various services. The default behavior of different ONTs may vary based on the factory settings. The pre-configuration file includes the factory default value for the residential gateway.Note: the pre-configuration file does not work with SFU ONTs; therefore, this feature applies only to Residential Gateway ONTs.The pre-configuration file can be used as is, but Alcatel-Lucent provides its customers with the flexibility to customize the pre-configuration file.This pre-configuration file enables operators to change the default behavior by downloading a customized pre-configuration based on customer inputs.This PRE XML file includes a custom OPERID.The Alcatel-Lucent defined index for the PRECONFIG file is: "PRE"HGU ONTs:G-240G-C,G-240W-A, G-240WZ-A, G-440G-ACFG ONT configuration delta file The XML-based CFG file updates the configurable parameters (the PRE settings) in the existing PRE file of a deployed ONT, where required.This configuration file enables operators to change the deployed behavior by downloading customized updates in the CFG file.This file is used only to modify the parameters in the PRE file; it is not used for service provisioning.No OPERID is required, because the update is based on the OPERID used for the PRE file.The Alcatel-Lucent defined index for the PRECONFIG DELTA file is: "CFG"XML Voice XML file The Voice XML file provides an alternate method for securely downloading voice parameters from the OLT, rather than using FTP (OMCIv1/OMCIv2) or HTTPS (TR-069). Downloading this file makes the applicable changes in the voice parameters.This file enables operators to change the voice behavior by downloading the updated voice XML file.Alcatel-Lucent recommends using this procedure, rather than embedded voice XML files.The Alcatel-Lucent defined index for the Voice XML file is: "XML"(1 of 2)R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
5 — ONT configuration file over OMCI5-4 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuideFilename conventionsAlcatel-Lucent provides the raw configuration files, which must be saved by the operator in a TAR file to be uploaded. TAR file names must be unique.The filenames of the raw configuration files may not adhere to the naming conventions outlined below. In this case, the files must be renamed to adhere to the naming conventions before the operator generates the TAR file. Filenames are not case-sensitive.ABCXXXXVERwhereABC is the file index type (PRE, CFG, XML, GFT)XXXX is the operator IDFor PRE and CFG, a valid operator ID is required For XML and GFT, any characters may be usedVER is the file version (from 001 to 999) Note: you cannot update the configuration using two files with the same name.5.3 ONT configuration file over OMCIUse this procedure to configure ONTs using configuration files via OMCI.GFT G.fast-related configuration file This text-based json script file controls the default behavior of the G.Fast ONT. This file includes the provisioning parameters of the G.fast transports layer; it does not include VLAN or QoS provisioning. While the ONT functions well with the default values; they can optionally be customized. While default values can work in VDSL mode, a download file is required for the device to function as a G.fast ONT.The Alcatel-Lucent defined index for the G.fast file is: "GFT"G-010F-A, G-010F-BFile Index Description Details Supported ONTs/DPU(2 of 2)Warning — Executing the following procedure will trigger the ONT to reboot, which will impact ongoing services.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
5 — ONT configuration file over OMCIAlcatel-Lucent 7368 ISAM ONT 5-5Edition 01G-240WZ-A Product GuideProcedure 5-1 Configuring an ONT using a configuration file via OMCI1Generate the TAR file to be uploaded to the OLT. Using the raw configuration file(s) provided by Alcatel-Lucent, generate the TAR file as follows:iOn a Linux platform, rename the raw configuration file to adhere to the naming convention, as described in section 5.2.ii Tar the ABCXXXXVER raw configuration file:tar -cf ABCXXXXVER.tar ABCXXXXVERWhere ABCXXXXVERIs the name of the file created in step i.This creates two files: ABCXXXXVER and ABCXXXXVER.tar.iii Rename ABCXXXXVER to ABCXXXXVER.orgiv Remove the “.tar” extension from ABCXXXXVER.tar file.2Upload the ABCXXXXVER TAR file to the /ONT/ directory in the OLT. A maximum of 250 files can be kept in the OLT file system.3Using OLT commands, download the TAR file to the ONT. For OLT commands, refer to the 7360 ISAM FX CLI Command Guide for 100_320Gbps FD NT and FX NT.Please note:•pri-cfgfile-pland/dnload or sec-cfgfile-pland/dnload can be 1 to 14 characters.•pri-cfgfile-pland and pri-cfgfile-dnload should be the same name.Examples Note: X can be 1 or 2 unless specified:iIf pland-cfgfileX= Disabled and dnload-cfgfileX= Disabled , no file will be downloaded to the ONT.ii If pland-cfgfileX=FILENAME1 and dnload-cfgfileX= Disabled , FILENAME1 will be downloaded and FILENAME1 will be made active. An ONT reboot is required.iii If pland-cfgfileX=Disabled and dnload-cfgfileX= FILENAME2 FILENAME2 will be downloaded and FILENAME2 will be made passive. An ONT reboot is not required.iv If pland-cfgfileX=FILENAME3 and dnload-cfgfileX= FILENAME 4, the OLT reports an error because the filenames are not the same.R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
5 — ONT configuration file over OMCI5-6 Alcatel-Lucent 7368 ISAM ONTEdition 01G-240WZ-A Product GuidevConfigure equipment interface … pland-cfgfile1=XMLXXXXXX1 and dnload-cfgfile1 XMLXXXXXX1 Configure equipment interface … pland-cfgfile2=XMLXXXXXX2 and dnload-cfgfile2 XMLXXXXXX2 Although the OLT permits the above two steps without reporting an error, Alcatel-Lucent does not recommend executing them, because the ONT may exhibit unexpected behavior.vi If pland-cfgfileX=Auto and dnload-cfgfileX= AutoThe OLT will download the XML file from "sw-ctr-list" (configure equipment ont sw-ctrl)4STOP. This procedure is complete.The ONT will distribute the configuration files to the different services based on the active indication from the OLT and on the Alcatel-Lucent defined index.The ONT automatically reboots to apply the configuration files. After the ONT reboots and reports the active version, the OLT completes the file download procedure.Operators must check the committed file from the OLT to verify whether the corresponding file has been applied. If an error occurs, contact Alcatel-Lucent for support. R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
Customer documentation and product supportCustomer documentationhttp://www.alcatel-lucent.com/myaccessProduct manuals and documentation updates are available at alcatel-lucent.com. If you are a new user and require access to this service, please contact your Alcatel-Lucent sales representative.Technical Supporthttp://support.alcatel-lucent.comDocumentation feedbackdocumentation.feedback@alcatel-lucent.comR05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01
© 2016 Alcatel-Lucent. All rights reserved..R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01

Navigation menu