Nokia of America BBTRX-09 LTE TRDU 2x60-7L (BC12/17) User Manual Blank Arch Spec doc

Alcatel-Lucent USA Inc. LTE TRDU 2x60-7L (BC12/17) Blank Arch Spec doc

Exhibit D Users Manual per 2 1033 c3

Document Title PAGE: 1 700MHz TRDU B12 User Manual DATE: 11-30-2012 NOTE: APPROVAL ON THIS PAGE SIGNIFIES THE ENTIRE DOCUMENT APPROVED. 700MHZ B12 TRDU USER MANUAL 1.0 DCP-xxxxxx 11-30-2012 Initial Release D. Fisher REV DCO NO. DATE CHANGE INFORMATION AUTHOR DOCUMENT NO.: 43-G07CRH-48-01B-U-00016 APPROVED BY PAGE NO.: 1 OF 17
Document Title PAGE: 2 700MHz TRDU B12 User Manual DATE: 11-30-2012 1.0 11-30-2012 Initial release D.Fisher REVISION HISTORY DOCUMENT NO.: 43-G07CRH-48-01B-U-00016 TITLE:700MHz TRDU B12 User Manual
Document Title PAGE: 3 700MHz TRDU B12 User Manual DATE: 11-30-2012 Table of Contents 1.0 Introduction ...................................................................................................................................................................................... 4 2.0 System Specifications ......................................................................................................................................................................... 5 4.0 Interfaces .......................................................................................................................................................................................... 7 4.1 Connectors ..................................................................................................................................................................................... 7 5.0 Mechanical ........................................................................................................................................................................................ 9 6.0 Photographs ...................................................................................................................................................................................... 10 6.1 Front Panel .................................................................................................................................................................................... 11 6.2 Chassis – Open Faced.................................................................................................................................................................... 12 6.3 RLB and PSM ................................................................................................................................................................................. 13 Conformance Statement ......................................................................................................................................................................... 14
Document Title PAGE: 4 700MHz TRDU B12 User Manual DATE: 11-30-2012 1.0 Introduction MTI’s G07CRH-48-01B is a 2x67W LTE TRDU which has two RF transmitters, two receivers and double duplexer filter. It is packaged in a single shelf-mounted module and is deployed in CPRI-compliant basestation networks. The TRDU features in-house developed dynamic digital power amplifier linearization technology which efficiently processes LTE transmissions, enabling: • High PA efficiency, resulting in low power consumption (475 W) • Low EVM waveform support. Adjustable from <4% to >12% • Efficient unbalanced power transmissions Additional features: • Hardware ready to support 1 LTE carrier with 1.4MHz, 3MHz, 5MHz and 10MHz bandwidth or up to 3 LTE carriers with 15MHz maximum bandwidth. • Low receiver noise figure (2dB), enables the base station OEM to reach excellent receiver sensitivity. Two Rx chains support receive diversity, increasing uplink performance even further. • Two externally pluggable SFP sockets enabling field selectable optical interfaces including 1310nm(UL)/ 1550nm(DL) single-mode single fiber and 850nm multi-mode dual fiber. Electrical interfaces are supported as well • Software supports Ethernet over CPRI and allows easy implementation of customer specific requirements. • Supports 2-way MIMO. Two units can be combined to support 4x4 MIMO or 2-way MIMO with 4 receive branches. • External AISG interface, I2C interface and a serial port for additional system control and monitoring. • Extensive Operations and Maintenance functionality supported through flexible O&M SW. Self-diagnosis and alarms continuously monitoring: • High MTBF (>375,000 hours)
Document Title PAGE: 5 700MHz TRDU B12 User Manual DATE: 11-30-2012 2.0 System Specifications Table 1: MECHANICAL/ENVIRONMENTAL SPECIFICATIONS PARAMETER TARGET SPECIFICATIONS Unit Dimensions 360.0 mm by 367.0 mm by110.0 mm=14.53 liter Unit Weight 14.5 Kg DC Power in -37V to -57VV (Nominal -48Vdc) Operational Temperature Range -40°C to +55°C Storage/Transportation Temperature Range -55ºC to +70ºC Enclosure Class IP20 Safety and Grounding EN 60950-1, IEC 60950, UL 60950-1 Storage ETSI EN 300 019-1-1 class 1.2, IEC 60721-3-1 Transportation ETSI EN 300 019-1-2 class 2.3, IEC 60721-3-2 Operational ETS 300 019-2-4 Standards Compliance IEC 68 Series, ETS EN 300 019 Series MTBF @ 40º C >375,000 Hours, SR-332 Table 2: SYSTEM SPECIFICATIONS Programmable Frequency Range Band12: DL Band 729-745MHz, UL Band 699~715MHz Power Supply Voltage -48V DC Total Power Consumption 475W typical Receive Diversity 2 antenna receive diversity standard Transmit Diversity 2 antenna transmit diversity standard Receiver Noise Figure 2.0 dB nominal, <2.2 dB at max operating temperature Instantaneous Bandwidth 15 MHz # of Carriers 3 LTE carrier with maximum 15MHz bandwidth Transmit Output Power 2x 67W (2x48.26 dBm) at antenna connector Output Power Accuracy +/- 0.5 dB Downlink Modulation LTE SEM/ACPR/EVM As defined in TS 36.104 V8.6.0 or latest CPRI Rate Support CPRI rates 1 through 5, hardware ready for rate 6 Optical or electrical Interface Standard SFP modules, field loadable
Document Title PAGE: 7 700MHz TRDU B12 User Manual DATE: 11-30-2012 4.0 Interfaces 4.1 Connectors PARAMETER Signals Connector type Connection CPRI Data/control SFP sockets Interface between the RRH and Node B controller LMT interface Debug RJ45/1394 Ethernet interface between the RRH and user maintenance Transmit/Receive Antenna Connector RF DIN Type female Transmit (Tx) and receive (Rx) the signals between the RRH and the antenna Power Supply Connector DC Power D-Sub Primary power input to the RRH ALD AISG AISG 8-pin Antenna Line Device I2C I2C RJ45 I2C control interface TX monitor RF DIN 1.0/2.3 female TX monitor ports Auxiliary RX I/O port RF DIN 1.0/2.3 female RX monitor and testing ports 4.1.1 CPRI Data/Control Optical/Electrical Connectors: SFP cages PIN # PIN Name Function Primary CPRI PRI Master Fiber LC connector to SFP module Secondary CPRI SEC Slave Fiber LC connector to SFP module 4.1.2 Debug Connector Debug Connector: RJ45 PIN # PIN Name Function 1 RJ45 TX+ Ethernet Transmit pair positive 2 RJ45 TX- Ethernet Transmit pair negative 3 RJ45 RX+ Ethernet Receive pair positive 4 Reserved Not used 5 Reserved Not used 6 RJ45 RX- Ethernet Receive pair negative 7 Reserved Not used 8 Reserved Not used 4.1.3 RF connectors PIN # PIN Name Function TX1/RX1 Transmit Receive DIN type Transmit/Receive RF port TX2/RX2 Transmit Receive DIN type Transmit/Receive RF port
Document Title PAGE: 8 700MHz TRDU B12 User Manual DATE: 11-30-2012 4.1.4 DC Power Connector DC Power Connector: Mini Fit Junior PIN # PIN Name Function 1 +24V +24V DC supply input 2 +24V RTN +24V DC supply return 4.1.5 AISG Connector 8-pin AISG PIN # Designation Max Current Capability Current Clamp Additional Notes / Requirements 1 +12 V DC Nominal 1.0 A 1.0 A RRH shall monitor and report current over CPRI. 2 not used Not used, not connected 3 RS485 B 4 RS485 GND RS485 ground, isolated from DC Return and Ground 5 RS485 A 6 +24V Nominal 850 mA 850 mA RRH monitor and report current over CPRI 7 DC Return 8 N/C Not used, not connected 4.1.6 I2C Connector 8-pin RJ-45 style connector PIN # Designation Max Current Capability Current Clamp Description Additional Notes/ Requirements 1 +24V_FL_1 * +24V pin 1 (power for external filter) RRH reports current over CPRI (current combined with Pin 2) Regulated supply. Not active until 100ms to 200ms after Pin 7 is pulled down through resistor (between 1K and 10Kohm) to ground. 2 +24V_FL_2 * +24V pin 2 (power for external filter) Same as Pin 1. Common internal source for Pin 1 & 2 is acceptable. 3 GND 4 GND 5 I2C_SDA Serial Data I/O (I2C) 4.7k ohm pull up resistor to 3.3V 6 GND 7 CTL_24V Control pin for +24V Pull down through 1kohm (or lower) resistance to enable 24V on pins 1 & 2. 8 I2C_SCL Serial Clock (I2C) Using pull-up resistors, pulled up to 3.3V.
Document Title PAGE: 9 700MHz TRDU B12 User Manual DATE: 11-30-2012 5.0 Mechanical
Document Title PAGE: 10700MHz TRDU B12 User Manual DATE: 11-30-2012 6.0 Photographs 6.1 Front Panel
Document Title PAGE: 12 700MHz TRDU B12 User Manual DATE: 11-30-2012 6.2 Chassis – Open Faced
Document Title PAGE: 13700MHz TRDU B12 User Manual DATE: 11-30-2012 6.3 RLB and PSM
Indoor applicationsThis equipment is intended for installation in restricted access locations where access iscontrolled or where access can only be gained by service personnel with a key or tool.Access to this equipment is restricted to qualified service personnel only.Antenna exposureAntenna installations for the 9412 eNodeB shall be performed in accordance with allapplicable manufacturer’s recommendations, and national laws and regulations. Toensure correct antenna installation, the antenna installer shall perform all necessarycalculations and/or field measurements to evaluate compliance with applicable nationallaws or regulations regarding exposure to electromagnetic fields. The supplier of radioequipment, the supplier of antenna equipment and the integrator and builder of the sitemust provide sufficient information so that the limits of the exclusion zones can bedetermined. Any changes to the antenna or other equipment in the transmit path mayrequire re-evaluation of the exposures to electromagnetic fields.Pursuant to 47 CFR Part 1, Subpart I, subject to the provisions of section 1.1307, allinstallations must be evaluated for requirements contained in Table 1, “Limits formaximum permissible exposure,” in section 1.1310.Packaging collection and recovery requirementsCountries, states, localities, or other jurisdictions may require that systems beestablished for the return and/or collection of packaging waste from the consumer, orother end user, or from the waste stream. Additionally, reuse, recovery, and/or recyclingtargets for the return and/or collection of the packaging waste may be established.For more information regarding collection and recovery of packaging and packagingwaste within specific jurisdictions, please contact the Alcatel-Lucent Services -Environmental Health and Safety organization. For installations not performed byAlcatel-Lucent Technologies, please contact the Alcatel-Lucent Customer SupportCenter at:Technical Support Services, within the United States: +1 630 224 4762, prompt 2Product conformance statements Page - 14United States........................................................................................................................................................................................................................................................................................................................................................................................................................................................................A-14 Alcatel-Lucent – ConfidentialSolely for authorized persons having a need to knowProprietary – Use pursuant to Company instruction401-703-614Issue 1-DRAFT3 April 2009DRAFTDRAFT
Product Conformance Statements - United StatesIntroductionThe statements that follow are the product conformance statements that apply to the9412 eNodeB when deployed in the United States.Federal Communications CommissionImportant! Changes or modifications not expressly approved by Alcatel-Lucent,Inc. could void the user’s authority to operate the equipment..FCC Part 15This device complies with Part 15 of the FCC Rules. Operation is subject to thecondition that this device does not cause harmful interference.FCC Part 15 Class B (as marketed)Important! This equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses, and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions,may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or television reception, whichcan be determined by turning the equipment off and on, the user is encouraged totry to correct the interference by one or more of the following measures:•Reorient or relocate the receiving antenna•Increase the separation between the equipment and receiver •Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected •Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhich•Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhich •Consultthedealeroranexperiencedradio/TVtechnicianforhelp. Product conformance statements United States........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4DRAFTDRAFT
•Connect the equipment into an outlet on a circuit different from that to whichthe receiver is connected•Consult the dealer or an experienced radio/TV technician for help.FCC Part 68This Part does not applicableTechnical Support Services, within the United States: +1 630 224 4762, prompt 2RF approvalThis equipment complies with Part 2, Subpart J - Equipment Authorization Procedures,of the FCC Rules.This device complies with Part 27-MISCELLANEOUS WIRELESS COMMUNICATIONS SERVICES, Subpart 27.53 (g)Product conformance statements United States........................................................................................................................................................................................................................................................................................................................................................................................................................................................................DRAFTDRAFT

Navigation menu