Nortech ATR430P Automobile Tag Reader User Manual 8A

Nortech International (PTY) LTD Automobile Tag Reader 8A

Contents

installation guide

708LF0212-AB November 1999                 Autotag-P Tag McGann Installation Guide                   Page 1 of 1            708LF0212-AB November 1999                   Autotag-P Tag McGann Installation Guide           Page 1 of 1McGann Technologies Tel: (612) 331 2020651 Taft Street NE Fax: (612) 331 5187Minneapolis MN 55413McGANNTECHNOLOGIESMcGann Technologies Tel: (612) 331 2020651 Taft Street NE Fax: (612) 331 5187Minneapolis MN 55413McGANNTECHNOLOGIESAUTOTAG-P TAG McGANN INSTALLATION GUIDEGeneralThe Tag is an active transponder designed to communicate with an Autotag-P Base-Stationunit. The Tag is triggered by the base-station when within range and transmits a unique codeback. It is available in an impact- and UV-resistant nylon-based housing. It operates over atemperature range of -30°C to +85°C and has a minimum working life of 3 years.(Replacement battery CR2032 3V lithium coin cell Nortech P/No MIE040001).  It isrecommended that an optional Tag holder (708MD0012), which allows for the removal of theTag from the vehicle, be used to hold the Tag in position on the windshield (windscreen).NB: Immersion of the Tag in liquid or interfering with the interior electronics will resultin the warranty being voided.Positioning1. For reliable operation the Tag should be positioned on the side of the vehicle closest tothe Base Station.  If, on entry or exit, the Base Station is on opposite sides of the vehicleposition the Tag at the centre of the windshield behind the rear-view mirror (see Figure 1).Ensure that the driver’s field of view is not obstructed.2. The Tag is NOT to be placed on the exterior of the vehicle.Figure 1. Tag placement on windshield (viewed from inside).Factors influencing selection of the Tag mounting position:• The main factor affecting performance is the proximity of metal or other conductingmaterial (such as the human body). For example, many dashboards are made of metal andcovered with a thin synthetic foam/rubber layer. If the Tag were placed on this it would notoperate. Likewise, if placed in a person’s shirt pocket operation could also not beguaranteed.• Also, if it were placed further within the car (instead of on the windscreen) the metal shell(of the car) will act as a shield, possibly preventing communication with the Base-Station.Mounting1. Use double sided mirror tape to mount the Tag or the optional holder.2. Ensure that the windscreen is thoroughly clean and dry, being free of any oil or grease.3. Remove the backing from the adhesive tape on the Tag or the optional holder and pressfirmly in place.4. If the optional Tag holder is used, insert the Tag into the holder.AUTOTAG-P TAG McGANN INSTALLATION GUIDEGeneralThe Tag is an active transponder designed to communicate with an Autotag-P Base-Stationunit. The Tag is triggered by the base-station when within range and transmits a unique codeback. It is available in an impact- and UV-resistant nylon-based housing. It operates over atemperature range of -30°C to +85°C and has a minimum working life of 3 years.(Replacement battery CR2032 3V lithium coin cell Nortech P/No MIE040001).  It isrecommended that an optional Tag holder (708MD0012), which allows for the removal of theTag from the vehicle, be used to hold the Tag in position on the windshield (windscreen).NB: Immersion of the Tag in liquid or interfering with the interior electronics will resultin the warranty being voided.Positioning1. For reliable operation the Tag should be positioned on the side of the vehicle closest tothe Base Station.  If, on entry or exit, the Base Station is on opposite sides of the vehicleposition the Tag at the centre of the windshield behind the rear-view mirror (see Figure 1).Ensure that the driver’s field of view is not obstructed.2. The Tag is NOT to be placed on the exterior of the vehicle.Figure 1. Tag placement on windshield (viewed from inside).Factors influencing selection of the Tag mounting position:• The main factor affecting performance is the proximity of metal or other conductingmaterial (such as the human body). For example, many dashboards are made of metal andcovered with a thin synthetic foam/rubber layer. If the Tag were placed on this it would notoperate. Likewise, if placed in a person’s shirt pocket operation could also not beguaranteed.• Also, if it were placed further within the car (instead of on the windscreen) the metal shell(of the car) will act as a shield, possibly preventing communication with the Base-Station.Mounting1. Use double sided mirror tape to mount the Tag or the optional holder.2. Ensure that the windscreen is thoroughly clean and dry, being free of any oil or grease.3. Remove the backing from the adhesive tape on the Tag or the optional holder and pressfirmly in place.4. If the optional Tag holder is used, insert the Tag into the holder.Recommendedgreater than50mm (2 inches)from the edge.Recommended mounting zonesRecommendedgreater than50mm (2 inches)from the edge.Recommended mounting zones

Navigation menu