Nortek Security and Control 2GIG PIR1345 Wireless Motion Sensor User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1161036
Application ID	Xsh489CdQjVL+p4xZIAG5Q==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	26.94kB (336722 bits)
Date Submitted	2009-08-28 00:00:00
Date Available	2009-08-28 00:00:00
Creation Date	2009-05-19 20:36:11
Producing Software	Microsoft® Office Publisher 2007
Document Lastmod	2009-05-19 20:36:11
Document Title	Users Manual
Document Creator	Microsoft® Office Publisher 2007
Document Author:	dglassman

Passive Infrared Motion Detector
same or equivalent type of battery as recommended by the manufacturer. (see Specifications)
2GIG-PIR1-345
Batteries must not be recharged, disassembled or disposed of in fire. Disposal of used batteries must be made in accordance with the waste recovery and recycling regulations in your area.
Operating Instructions
Keep away from small children. If batteries are swallowed, promptly see a doctor.
California Only: This Perchlorate warning applies only to Manganese Dioxide Lithium cells sold or distributed ONLY in California,
USA. Perchlorate Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate.
The 2GIG-PIR1-345 Passive Infrared Motion Detector is a wall-mounted unit with wide angle
motion protection. The device has a 30 ft. x 50 ft. range and is pet immune up to 55 lbs.
Specifications
Installation/Mounting & Programming Guidelines
To setup the motion detector:
1.
Remove the screw from the bottom of the case and open the PIR (see Figure 2).
2.
Install the recommended battery, making sure to observe the correct polarity.
3.
Set the left jumper (PET IMMUNITY) to either 33 lbs. (15 kg; default) or 55 lbs (25 kg).
(see Figure 1)
4.
Set the right jumper (SENSITIVITY) to either HI (default) or LO (see Figure 1 ).
5.
Wait 10 seconds for the power up delay.
6.
Enter the programming mode for a wireless device on the control panel.
7.
Enroll the PIR by pressing and holding the tamper switch on the PIR for 2 seconds while control panel is in
learn mode.
To mount the motion detector, with or without the bracket, following the corresponding
guidelines:
1.
2.
3.
4.
5.
6.
1.
2.
With Bracket (see Figure 2)
Screw part A in to part B.
Select either the corner mount (part C) or flat wall mount (part D).
Mount the selected bracket (C or D) at a height of 7.5 ft (2.3 m) on the wall using
the supplied long screws with anchors.
Place the assembly of parts A and B on the shaft of bracket C or D.
Insert a screw from the top of part B to hold the assembly to the shaft of bracket C
or D.
Attach the main body of the PIR to the mounted back with the screw at the bottom
of the case.
Without Bracket (see Figure 3)
For corner mounting use the supplied long screws with anchors and mount the PIR
case back using either the upper 2 corner mount screw holes or the lower 2 corner
mount screw holes and mount the PIR back at a height of 7.5 ft (2.3 m). Attach
the main body of the PIR to the mounted back with the screw at the bottom of the
PIR.
Wireless Signal Range
Code Outputs
Transmitter Frequency
Transmitter Frequency Tolerance
Transmitter Bandwidth
Modulation Type
Unique ID Codes
Supervisory Interval
Peak Field Strength
Sensor Type
Pet Immunity
Sensitivity Jumper
Suggested Mounting Height
Sensor Range
Maximum Horizontal Sensing Angle
Dimensions (LxWxH)
Weight (including battery & bracket)
Housing Material
Color
Operating Temperature
Relative Humidity
Battery (included, not installed)
Battery Life
Regulatory Listing(s)
Warranty*
Included Accessories
700 ft., open air, with 2GIG Wireless Alarm Control Panel
Alarm; Alarm Restore; Tamper; Tamper Restore; Supervisory; Low Battery
345.000 MHz (crystal controlled)
± 10 kHz
24 kHz
Amplitude Shift Keying—On/Off Keying (ASK-OOK)
Over one (1) million different code combinations
70 minutes
Typical 50,000 uV/m at 3m
Quad element
Selectable: 15 kg (33 lbs.; default) or 25 kg (55 lbs.)
Selectable: High (default) or Low
7.5 ft. (2.3 m)
30 ft. (9.1 m) x 50 ft. (15.2 m)
110°
3.2 x 2.5 x 1.9 in. (8.12 x 6.35 x 4.82 cm)
3.7 oz. (104.9 g)
ABS plastic and poly-carbonate
White
32° to 120°F (0° to 49°C)
5-95% Non-Condensing
One (1) Panasonic CR123A, 3 VDC, 1550 mAh or equivalent Lithium cylindrical battery
5 years
ETL, FCC Part 15, Industry Canada
Two (2) years
Mounting brackets, two (2) Phillip’s head screws, two (2) plastic wall anchors, magnet
FCC COMPLIANCE STATEMENT*
Figure 1
This device complies with FCC Rules and Regulations as Part 15 devices, as well as Industry Canada Rules and Regulations.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Note: Changes or modifications to the device may void FCC compliance.
FCC ID: WDQ-PIR1345
Industry Canada ID: 7794A-PIR1345
For mounting the PIR on a flat wall use the supplied long screws with anchors and
mount the PIR case back using the 2 wall mount screw holes in the center of the
back and mount the back at a height of 7.5 ft (2.3 m). Attach the main body of
the PIR to the mounted back with the screw at the bottom of the PIR.
*For more warranty and compliance information, visit our website (www.2gig.com).
Testing
Figure 2
Figure 4
Before placing the sensor in Walk or RF Test mode, make sure the control panel is in Install
or User Walk Test mode.
1.
2.
Walk Test
Place the supplied magnet over the arrow on the left side of the PIR for 2 seconds and
then remove it.
Move in the area that is to be covered by the PIR and make sure that the LED on the
PIR flashes every time you move. This will continue for 1 minute to allow you to check
the coverage of the PIR beam. NOTE: There is a 3 second delay between flashes.
RF Test
Place the supplied magnet over the arrow on the left side of the PIR for 5 seconds and then
remove it. The PIR will continue to send RF transmissions for 1 minute, and will be indicated
by the control panel.
Battery Installation & Replacement
Figure 3
Remove back cover by unscrewing bottom screw and pull back cover from bottom to top. Use only the recommended replacement
batteries (see Specifications). Be sure to observe the polarity.
WARNING! The polarity of the battery must be observed, as shown (see Figure 1). Improper handling of lithium
batteries may result in heat generation, explosion or fire, which may lead to personal injuries. Replace only with the
Technical Support:
1-866-670-1591
www.2gig.com
05/19/09
©2009

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 1
Language                        : en-US
Tagged PDF                      : Yes
Author                          : dglassman
Create Date                     : 2009:05:19 20:36:11
Modify Date                     : 2009:05:19 20:36:11
Producer                        : Microsoft® Office Publisher 2007
Creator                         : Microsoft® Office Publisher 2007

EXIF Metadata provided by EXIF.tools