Nortek Security and Control 2GIG SMO1345 Wireless Smoke Sensor User Manual 229910A indd

Download:
Mirror Download [FCC.gov]
Document ID	1166623
Application ID	onxrmC0DpjZ5i3hG0SK6EQ==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	22.3kB (278790 bits)
Date Submitted	2009-09-09 00:00:00
Date Available	2009-09-09 00:00:00
Creation Date	2009-06-08 08:56:45
Producing Software	Acrobat Distiller 8.1.0 (Windows)
Document Lastmod	2009-06-08 09:08:43
Document Title	229910A.indd
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Copyright © 2009 Linear LLC

PRINTERS INSTRUCTIONS
INSTR,INSTL,2GIG-SMKE1-345 - P/N: 229910 X3 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500” X 11.000” - SCALE: 1-1 - SIDE 1 of 2
PRODUCT DESCRIPTION
2GIG-SMKE1-345
The 2GIG-SMKE1-345 is a photoelectric smoke alarm with a built-in
transmitter designed for use with the 2GIG-CNTRL-345 security system.
When smoke is detected, the alarm sounds a loud local alarm. Twenty
seconds after the local alarm sounds, the built-in transmitter sends a
digitally coded wireless signal to the Control Panel. The wireless signal
will be repeated every 20 seconds as long as smoke is still present.
WIRELESS
PHOTOELECTRIC
SMOKE
ALARM
The 2GIG-SMKE1-345 detector can send four different signals: alarm,
test, low battery, and status.
The Control Panel must be programmed to the detector’s serial
number before system testing and operation. Refer to the Control
Panel’s instructions for details on programming.
REMOVE PROTECTIVE COVER
REMOVE
PROTECTIVE
COVER AND
DISCARD
The detector is powered by a 3-volt lithium battery. The battery is supplied
with the detector and can power the unit for up to five years. If the battery
voltage drops below a preset level the alarm will sound low battery beeps
and a low battery signal will be sent to the Control Panel.
Installation
Instructions
CM
L IS T
Every hour, the detector will send a status transmission to the Control
Panel. The hourly signal updates the Control Panel with the detector’s
condition. By monitoring status transmissions, the Control Panel can
determine that the detector is still present in the installation and if it has
a low battery.
Maintenance: Occasionally clean the outside casing with a cloth. Ensure
that the holes on the front of the alarm are not blocked with dirt and dust.
Do not paint, and do not use cleaning agents, bleach, or polish on
the detector.
Technical Support
866-670-1591
www.2gig.com
REMOVE MOUNTING PLATE
TWIST MOUNTING
PLATE TO UNLOCK
REMOVE BATTERY TAB
CHOOSE ALARM LOCATION
PULL TO CONNEC
BATTERIES
REMOVE
BATTERY TAB
TO APPLY
POWER
REMOVE
MOUNTING
PLATE
INSTALL MOUNTING PLATE
SCREW
ANCHORS
FOR WALLBOARD
3-VOLT LITHIUM BATTERY
TYPES: DURACELL DL123A,
PANASONIC CR123A,
SANYO CR123A, ADEMCO 466
PROGRAM CONTROL PANEL
REFER TO CONTROL PANEL'S INSTRUCTIONS TO
PREPARE RECEIVER TO ACCEPT THE DETECTOR'S
SERIAL NUMBER
MOUNT ALARM ON PLATE
MATCH ALIGNMENT TABS IN
PLATE WITH TABS IN COVER
PRESS AND RELEASE
TEST BUTTON TO
SEND SIGNAL
OR
DETECTOR
PLASTIC
SINGLE-GANG
ELECTRICAL BOX
A TEST SIGNAL
WILL BE SENT
AS SOON AS THE
SWITCH IS RELEASED
CONTROL PANEL
TWIST SMOKE
ALARM CLOCKWISE
TO LOCK ONTO
MOUNTING PLATE
PRINTERS INSTRUCTIONS
INSTR,INSTL,2GIG-SMKE1-345 - P/N: 229910 X3 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500” X 11.000” - SCALE: 1-1 - SIDE 2 of 2
TEST SYSTEM
LOW BATTERY CONDITION
When the alarm detects a low battery, the sounder will chirp and the
red LED will blink every 45 seconds. The green LED will be off. Pressing
the test switch will silence the chirp for 12 hours but will not affect the
LEDs. During this silence period, the test switch is disabled. If an alarm
condition occurs while the detector is in this chirp silence mode, the alarm
will sound. Once the alarm condition has been removed and the detector
returns to the standby state, the low battery chirp will resume every 45
seconds.
TO TEST AN ACTUAL FIRE
ALARM RESPONSE OF THE
SYSTEM, TEST SWITCH
MUST BE HELD FOR
20 SECONDS
STANDARD FOR ALARM LOCATION
VERIFY THAT
CONTROL PANEL
ACTIVATES
DETECTOR LED INDICATORS
At Power up = Green/Red blinks every 5 seconds
Standby = Green blinks every 10 seconds
Alarm = Red blinks every 1 second
Maintenance = Red blinks every 5 seconds
Low Battery = Red blinks every 45 seconds
✔ Ceiling mounted smoke alarms should be located in the center of
the room or hall, or not less than 4 inches from any wall. When the
alarm is mounted on a wall, the top of the alarm should be 4 to 12
inches from the ceiling.
✔ Do not install smoke alarms where normal ambient temperatures
are above 100°F (37.8°C), or below 40°F (4°C). Also, do not
locate alarm in front of air conditioners, heating registers, or
other locations where normal air circulation will keep smoke from
entering the detector.
A-2.5.2.1 Smoke Detection - Are More Smoke Alarms Desirable? The
required number of smoke alarms might not provide reliable early warning
protection for those areas separated by a door from the areas protected
2-1.1.1 Smoke alarms shall be installed outside of each by the required smoke alarms. For this reason, it is recommended that the
separate sleeping area in the immediate vicinity of the bedrooms householder consider the use of additional smoke alarms for those areas
and on each additional story of the family living unit including for increased protection. The additional areas include the basement,
basements and excluding crawl spaces and unfinished attics. bedrooms, dining room, furnace room, utility room, and hallways not
In new construction, a smoke alarm shall be installed in each protected by the required smoke alarms. The installation of smoke alarms
in kitchens, attics (finished or unfinished), or garages is not normally
sleeping room.
recommended, as these locations occasionally experience conditions
2-1.1.2 For family living units with one or more split levels (i.e., that can result in improper operation.
The smoke alarm should be installed in accordance with National Fire
Protection Association (NFPA) Standard 72, which reads as follows:
adjacent levels with less than one full story separation between Smoke alarms are not to be used with detector guards unless the
levels), a smoke alarm required by 2-1.1.1 shall suffice for an combination has been evaluated and found suitable for the purpose.
adjacent lower level, including basements. (Exception: Where
there is an intervening door between one level and the adjacent
lower level, a smoke alarm shall be installed on the lower level.)
FIRE PREVENTION AND ESCAPE
The purpose of an early warning smoke alarm is to detect the presence
of fire in its early stages, and sound an alarm giving the occupants
more time to exit the premise before the smoke reaches a dangerous
concentration level.
Fires start even with the best of housekeeping and fire prevention
procedures. Fire is an unexpected event. Early warning detection alerts
occupants in time to act.
KNOW FIRE HAZARDS. No detection device can protect life in all
situations. Therefore, safeguards should be taken to avoid such potentially
dangerous situations as: smoking in bed, leaving children home alone,
cleaning with flammable liquids such as gasoline.
The best fire protection is minimizing fire hazards through proper storage
of materials and general good housekeeping techniques. A cluttered
basement, attic, or other storage area is an open invitation to fire.
Careless use of combustible materials and electrical appliances, or
overloading of electrical outlets are other prime causes in starting fires.
It is most important that explosive and/or fast burning materials be
eliminated from the home, if at all possible.
Even after proper precautions have been taken, fires can start. Be
prepared.
IN CASE OF FIRE. Leave immediately. Don’t stop to pack or search
for valuables. In heavy smoke, hold your breath and stay low - crawl if
necessary. The clearest air is usually at the floor.
If you have to go through a closed door, carefully feel the door and
door knob to see if undue heat is present. If they seem relatively cool,
brace your foot against the bottom of the door with your hip against the
door and one hand against the top edge. Open it slightly. If a rush of
hot air is felt, slam the door quickly and latch it. Unvented fire tends to
build up considerable pressure. Be sure all the household realizes and
understands this danger.
Use your neighbor’s phone or a street fire alarm box. The job of
extinguishing the fire should be left to the professionals. Too many
unforeseen things can occur when inexperienced people try to extinguish
a fire.
FCC COMPLIANCE STATEMENT
This device complies with FCC Rules Part 15.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
BE PREPARED. Perform fire drills regularly. Use them to assure
recognition of an alarm signal. For your protection, simulate different
circumstances (smoke in hall, in living room, etc.). Then have everyone
react to the situation.
Draw a floor plan and show two exits from each room. Frequently a knotted
rope or ladder from a window will serve this purpose. It is important that
children be instructed carefully, because they tend to hide in times of
crisis.
It is imperative that one meeting place outside the home be established.
You should insist that everyone meet there during an alarm. This will
eliminate the tragedy of someone re-entering the house for a missing
member who is actually safe.
If you have children and/or invalids residing in your household, you can
help your fire department. Most fire departments have window decals
available for use in children’s or invalid’s bedrooms. Properly used, these
decals will quickly identify sleeping quarters of these individuals and show
the fire department where to look first for members of your household.
✔ Additional information on Household Fire Warning is available
at nominal cost from: The National Fire Protection Association,
Batterymarch Park, Quincy, MA 02269. Request Standard No.
NFPA 72
EXAMPLE ALARM LOCATIONS
LIMITED WARRANTY
This 2GIG Technologies product is warranted against defects in material and
workmanship for two (2) years. This warranty extends only to wholesale
customers who buy direct from 2GIG Technologies or through 2GIG Technologies’
normal distribution channels. 2GIG Technologies does not warrant this product to
consumers. Consumers should inquire from their selling dealer as to the nature of
the dealer’s warranty, if any. There are no obligations or liabilities on the part of
2GIG Technologies for consequential damages arising out of or in connection
with use or performance of this product or other indirect damages with respect
to loss of property, revenue, or profit, or cost of removal, installation, or
reinstallation. All implied warranties, including implied warranties for merchantability
and implied warranties for fitness, are valid only until the warranty expires. This 2GIG
Technologies Warranty is in lieu of all other warranties express or implied.
All products returned for warranty service require a Return Product Authorization
Number (RPA#). Contact 2GIG Technologies at 1-866-670-1591 for an RPA# and
other important details.
For additional warranty and compliance information, visit our Web site at: www.2gig.com
IMPORTANT!!!
Radio controls provide a reliable communications link and fill an important need in portable
wireless signaling. However, there are some limitations which must be observed.
✶ For U.S. installations only: The radios are required to comply with FCC Rules
and Regulations as Part 15 devices. As such, they have limited transmitter
power and therefore limited range.
✶ A receiver cannot respond to more than one transmitted signal at a time
and may be blocked by radio signals that occur on or near their operating
frequencies, regardless of code settings.
✶ Changes or modifications to the device may void FCC compliance.
✶ Infrequently used radio links should be tested regularly to protect against
undetected interference or fault.
✶ A general knowledge of radio and its vagaries should be gained prior to acting
as a wholesale distributor or dealer, and these facts should be communicated
to the ultimate users.
Copyright © 2009
229910 X3

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Keywords                        : 
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2009:06:08 09:08:43-07:00
Create Date                     : 2009:06:08 08:56:45-07:00
Metadata Date                   : 2009:06:08 09:08:43-07:00
Format                          : application/pdf
Title                           : 229910A.indd
Creator                         : Copyright © 2009 Linear LLC
Document ID                     : uuid:e68a9740-462b-417c-80df-6958ac2c9fd9
Instance ID                     : uuid:b934e514-a876-4e20-ab83-102a257aa847
Startup Profile                 : Print
Page Count                      : 2
Author                          : Copyright © 2009 Linear LLC
Warning                         : [Minor] Ignored duplicate Info dictionary

EXIF Metadata provided by EXIF.tools