Nortek Security and Control 00106 Security/Remote Control Transmitter User Manual 235166B ITIFOB01 Instructions indd
Nortek Security & Control LLC Security/Remote Control Transmitter 235166B ITIFOB01 Instructions indd
User manual
Copyright © 2013 Linear LLC 235166 AX1
ITIFOB01
4-BUTTON
KEY FOB
TRANSMITTER
Operation
Instructions
PRODUCT DESCRIPTION
The Model ITIFOB01 is a four button, battery powered, water-resistant,
transmitter designed for use with GE security systems.
Pressing one of the buttons on the transmitter sends a digital coded
wireless signal to its companion receiver and lights the red signal indicator
on the transmitter. The transmitter sends variations of the code depending
on which button is pressed. The code format features over 4 billion
different encrypted code sequences. To ensure sending a signal, press
the transmitter button for a minimum of 2 seconds.
Each transmitter is powered by two self-contained type CR2025 3-volt
lithium batteries (included). Every activation, the transmitter sends its
battery status to the receiver. If the battery is low, a low battery signal is
sent to the receiver.
Receivers must be programmed to the transmitter’s code before system
testing and operation. Refer to the receiver’s instructions for details on
operation and programming.
The transmitter is supplied with an optional mounting bracket and a belt
clip. For stationary applications, the transmitter snaps into the mounting
bracket. For portable use, the belt clip attaches to mounting bracket
allowing the unit to be clipped to shirt pocket or slid onto a belt.
FEATURES
PROGRAMMING BATTERY REPLACEMENT LINEAR LIMITED WARRANTY
USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340
www.linearcorp.com
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,ITI/GE 4 BTN FOB - FILE NAME: 235166 AX1 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500” X 5.500” - FOLDING: 3 FOLD ALTERNATE, FINISH WITH LOGO SHOWING - SCALE: 1-1
BELT
CLIP
MOUNTING
BRACKET
KEY FOB
TRANSMITTER
ACTIVATION
BUTTONS
1
TWIST COIN IN
SLOT TO OPEN
TRANSMITTER
2
CAREFULLY REMOVE
RETAINING SCREW
AND LIFT OUT BOARD
3
REPLACE BATTERIES
WITH TWO TYPE CR2025
LITHIUM BATTERIES
PLUS SIDE DOWN
CR2025
4
REVERSE STEPS TO
REASSEMBLE TRANSMITTER
BE CAREFUL NOT TO
DROP SCREW ON BOARD
KEEP AWAY FROM SMALL CHILDREN.
IF BATTERIES ARE SWALLOWED,
PROMPTLY SEE A DOCTOR. DO NOT
TRY TO RECHARGE THESE
BATTERIES. DISPOSAL OF USED
BATTERIES MUST BE MADE IN
ACCORDANCE WITH THE WASTE
RECOVERY AND RECYCLING
REGULATIONS IN YOUR AREA.
SIDE
SIDE
NOTICE TO USERS IN CALIFORNIA - CR COIN CELL LITHIUM
BATTERY INFORMATION: THIS PRODUCT CONTAINS A CR
COIN CELL LITHIUM BATTERY WHICH CONTAINS
PERCHLORATE MATERIAL - SPECIAL HANDLING MAY APPLY -
SEE WWW.DTSC.CA.GOV/HAZARDOUSWASTE/PERCHLORATE
CR2025
1
REFER TO THE SECURITY SYSTEM'S
INSTRUCTIONS AND PLACE THE
RECEIVER IN PROGRAM MODE
SET ANY OTHER SYSTEM
PROGRAMMING OPTIONS FOR
THE TRANSMITTER
2
PRESS A BUTTON ON THE
TRANSMITTER TO SEND
A SIGNAL
4
TEST THE SYSTEM
5
VERIFY THAT THE TRANSMITTER
HAS BEEN "LEARNED" BY
THE RECEIVER
3
This Linear product is warranted against defects in material and
workmanship for twelve (12) months. This warranty extends
only to wholesale customers who buy direct from Linear
or through Linear’s normal distribution channels. Linear does not
warrant this product to consumers. Consumers should inquire from
their selling dealer as to the nature of the dealer’s warranty, if any.
There are no obligations or liabilities on the part of
Linear LLC for consequential damages arising out
of or in connection with use or performance of this
product or other indirect damages with respect to
loss of property, revenue, or profi t, or cost of removal,
installation, or reinstallation. All implied warranties,
including implied warranties for merchantability and implied
warranties for fi tness, are valid only until the warranty expires. This
Linear LLC Warranty is in lieu of all other warranties
express or implied.
All products returned for warranty service require a Return Product
Authorization Number (RPA#). Contact Linear Technical Services at
1-855-546-3351 for an RPA# and other important details.
Any changes or modifi cations not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
Les changements ou modifi cations non approuvés expressément par
la partie responsable de la conformité pourrait annuler l’autorité de
l’utilisateur à faire fonctionner l’équipement.
IMPORTANT! Linear radio controls provide a reliable
communications link and fi ll an important need in portable wireless
signaling. However, there are some limitations which must be
observed.
• For U.S. installations only: The radios are required to comply with
FCC Rules and Regulations as Part 15 devices. As such, they have
limited transmitter power and therefore limited range.
• A receiver cannot respond to more than one transmitted signal
at a time and may be blocked by radio signals that occur on or
near their operating frequencies, regardless of code settings.
• Changes or modifi cations to the device may void FCC compliance.
• Infrequently used radio links should be tested regularly to
protect against undetected interference or fault.
• A general knowledge of radio and its vagaries should be gained
prior to acting as a wholesale distributor or dealer, and these
facts should be communicated to the ultimate users.
This device complies with FCC Part 15 and Canada Rules and
Regulations. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference and (2) this device
must accept any interference received, including interference that
may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes : (1) l’appareil ne doit
pas produire de brouillage, et (2) l’utilisateur de l’appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le fonctionnement.