Nortek Security and Control 00118 Security/Remote Control Transmitter User Manual 235686A GD00Z 1 Instructions IRIS indd

Download:
Mirror Download [FCC.gov]
Document ID	2205596
Application ID	ZpxLm8F2zGYLZac7lh9HCw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	34.47kB (430904 bits)
Date Submitted	2014-03-04 00:00:00
Date Available	2014-03-05 00:00:00
Creation Date	2014-01-23 08:31:38
Producing Software	Acrobat Distiller 10.1.9 (Windows)
Document Lastmod	2014-01-23 08:32:02
Document Title	235686A GD00Z-1 Instructions IRIS.indd
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Copyright © 2014 Linear LLC

PRINTER’S INSTRUCTIONS:
INSTR,INSTL,GD00Z-1 - LINEAR P/N: 235686 X21 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 1 OF 2
1. PRODUCT DESCRIPTION
GD00Z-1
GARAGE DOOR OPENER
REMOTE COMMAND
CONTROLLER
with TILT SENSOR
Installation Instructions
USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340
www.linearcorp.com
Z-Wave® is a registered trademark of Sigma Designs Inc. and/or its subsidiaries.
3. PRODUCT FEATURES
CONTROLLER
STATUS
INDICATOR
2. SAFETY NOTES
The Model GD00Z-1 is a garage door opener Remote Command Controller with
built-in Z-Wave® interoperable two-way RF mesh networking technology designed for
use with Lowe’s Iris® hub. A garage door opener connected to the Controller can be
remotely activated using the Iris web interface or Iris mobile applications.
The GD00Z-1 Controller connects to the garage door opener’s pushbutton wall
console terminals and communicates with the Iris hub using Z-Wave radio signals. A
wireless tilt sensor mounts on the garage door and reports the door’s position to the
Controller. When the Controller receives a command from the Iris hub, it will open or
close the garage door.
Anytime the garage door opener is activated remotely by the Controller, a warning
indicator flashes and a beeper sounds for five seconds before the door begins to move.
If, due to an obstruction or other cause, the door does not completely open or close
when it is activated remotely, the Controller will pause for 30 seconds. After the delay,
a second remote activation can be attempted. If the door does not complete its motion
on the second attempt, the Controller will suspend operation until the door is operated
locally with the opener’s pushbutton wall console.
The Controller is powered by a plug-in power supply. The Model TILT 345 tilt sensor
is powered by a 2032 lithium battery. If the tilt sensor battery is low, it will be reported
to the Iris hub by the Controller. A link button and status light are provided on the
Controller for adding or removing the device with the Iris hub.
Four screws and anchors are provided for mounting the Controller. An adjustable
controller mounting bracket with hardware is supplied for installing the unit onto the
door opener’s hanging hardware. The wireless tilt sensor mounts with double sided
tape or the two screws supplied.
4. TILT SENSOR INSTALLATION AND BATTERY
WARNING
LIGHT
WARNING
This system can be installed on sectional type (roll up) doors
only per (UL-325). DO NOT INSTALL ON ONE-PIECE DOORS!
WARNING
The Remote Command Controller must be mounted in
the garage, in sight of the garage door, where the visual
and audible movement warning indicators can be clearly
seen and heard.
WARNING
Do not install the Remote Command Controller on
garage door operators manufactured prior to 1993
(models without an operational safety beam entrapment
detection system).
5. PAIRING WITH IRIS
TO ACTIVATE THE TILT SENSOR, REMOVE THE BATTERY PROTECTION PULL STRIP
WALL
OUTLET
www.lowes.com/iris
ARROWS ON PLATE
& SENSOR POINT UP
ATTACH MOUNTING PLATE
TO TOP PANEL OF THE DOOR
POWER
INPUT
JACK
WARNING
This operator system is equipped with an unattended
operation feature. This door could move unexpectedly.
NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR!
LINK
BUTTON
SNAP SENSOR ONTO
THE MOUNTING PLATE
POWER
SUPPLY
LINK
BUTTON
CONTROLLER
POWER
INPUT
JACK
"UP"
ARROWS
POST ON
BOTTOM
CONTROLLER
CONNECTION
WIRES
TILT
SENSOR
POWER
SUPPLY
RETAINING
BRACKET
DOUBLE SIDED
MOUNTING TAPE,
SCREWS AND ANCHORS
ADJUSTABLE
MOUNTING
BRACKET
(OPTIONAL)
POWER
SUPPLY
TO PAIR WITH
THE IRIS HUB
PARING THE CONTROLLER
USE DOUBLE SIDED TAPE OR
THE TWO MOUNTING SCREWS SUPPLIED
(DRILL 1/16" PILOT HOLES IF REQUIRED)
1 FROM THE IRIS WEB SITE, CLICK
IRIS WILL NOTIFY YOU WHEN
THE BATTERY IS LOW,
REPLACE THE BATTERY WITH
A TYPE CR2032 COIN CELL
TO OPEN THE CASE, TWIST
A SMALL SCREWDRIVER
SLOT
IN CASE SLOT
PLUS SIDE UP !!!
INSERT THE
BATTERY
INTO THE
TRANSMITTER
CR2032
"DEVICES", THEN CLICK THE
"ADD DEVICES" BUTTON
2 SELECT GARAGE DOOR
CONTROLLER FROM THE LIST
TO REMOVE FROM
THE IRIS HUB
REMOVING THE CONTROLLER
1 FROM THE IRIS WEB SITE,
CLICK "DEVICES"
2 ON THE GARAGE DOOR
CONTROLLER DEVICE CLICK
"MANAGE", THEN CLICK "REMOVE"
3 FOLLOW THE ON-SCREEN
3 FOLLOW THE ON-SCREEN
4 WHEN INSTRUCTED, PRESS
4 WHEN INSTRUCTED, PRESS
INSTRUCTIONS TO PAIR THE
CONTROLLER WITH THE HUB
THE LINK BUTTON ON THE
CONTROLLER
INSTRUCTIONS TO UN-PAIR THE
CONTROLLER WITH THE HUB
THE LINK BUTTON ON THE
CONTROLLER
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,GD00Z-1 - LINEAR P/N: 235686 X21 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 2 OF 2
6. CONTROLLER MOUNTING
7.
CONTROLLER CONNECTIONS
THE CONTROLLER TYPICALLY
MOUNTS ON THE CEILING
NEAR THE OPENER AND
THE POWER OUTLET
TILT SENSOR
MOUNTED ON
THE TOP PANEL
OF THE DOOR
8. SYSTEM OPERATION
PLUG THE POWER CORD
INTO THE POWER INPUT
JACK ON THE CONTROLLER
1 USE THE IRIS WEB SITE AND MOBILE
APPS TO CONTROL YOUR GARAGE
DOOR, VIEW STATUS, AND SET
CUSTOM RULES
BEEP
BEEP
BEEP
2 THE CONTROLLER WILL BEEP AND
THE CONTROLER'S WARNING
LAMP MUST BE VISIBLE IN
ALL DOOR POSITIONS
THE CONTROLLER CAN ALSO BE ATTACHED TO THE OPENER'S
HARDWARE USING THE ADJUSTABLE MOUNTING BRACKET
THE OPTIONAL ADJUSTABLE
MOUNTING BRACKET FITS
3 WAYS ON THE CONTROLLER
3/16" HOLES
FOR ANCHORS
SECURE
BRACKET
WITH SCREW
CONNECT THE CONTROLLER CONNECTION
WIRES TO THE PUSHBUTTON WALL
CONSOLE TERMINALS ON THE GARAGE
DOOR OPENER. THE TERMINALS MAY BE
NAMED "PWC", "WC", "PB", "PUSHBUTTON",
OR "RED AND WHITE". TERMINAL NAMES
AND LOCATIONS VARY BY MODEL.
PLUG THE POWER SUPPLY
INTO 115 VAC OUTLET
AND SECURE IT WITH
THE RETAINING BRACKET
3 THE CONTROLLER WILL ACTIVATE
DO NOT DISCONNECT
ANY WIRES CURRENTLY
CONNECTED TO THE
GARAGE DOOR OPENER !!!
EITHER WIRE
CAN CONNECT
TO EITHER
TERMINAL
INDENT
INDENT
USE THE FOUR SCREWS
AND ANCHORS TO MOUNT
THE CONTROLLER ABOVE
THE OPENER
1. The warning light will flash and the warning beeper will sound
five seconds before the door opener is activated. STAY CLEAR
OF THE DOOR, AND DOOR OPENER. THEY ARE ABOUT TO
MOVE!
2. If the door does not completely open or close after remote
activation, the Controller will allow user to try to operate the door
one more time. If the second attempt fails, the Controller will go
into lock-out mode and blink the status indicator. See Note #3.
LINEAR LIMITED RETAIL WARRANTY
POSSIBLE
CAUSE
CORRECTIVE ACTION
The Controller does
not flash or beep
when activated.
No power to
the Controller.
1. Make sure the power supply is
plugged in securely to a live outlet.
The Controller flashes
and beeps when
activated but the door
does not move.
Obstruction
blocking
the door or
incorrect
wiring.
1. Make sure that there are no
obstacles preventing the door from
moving.
Garage door opens or
closes, but the status
does not change on
the Iris website or
mobile app.
The tilt sensor
signal is
not being
received by the
Controller.
1. Make sure the tilt sensor is
mounted correctly on the garage
door, with the arrow pointing up.
PROBLEM
2. Make sure the power cord is plugged
in securely to the Controller.
NOTICE TO USERS IN CALIFORNIA - CR COIN CELL LITHIUM BATTERY INFORMATION:
THIS PRODUCT CONTAINS A CR COIN CELL LITHIUM BATTERY WHICH CONTAINS
PERCHLORATE MATERIAL - SPECIAL HANDLING MAY APPLY - SEE
www.dtsc.ca.gov/hazardouswaste/perchlorate
Changes or modifications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
Les changements ou modifications non approuvés expressément par la partie
responsable de la conformité pourrait annuler l’autorité de l’utilisateur à faire
fonctionner l’équipement.
APP WILL SHOW THE NEW STATUS
OF THE DOOR AFTER THE DOOR
COMPLETES ITS CYCLE
STAY CLEAR
OF THE DOOR !!!
10. TROUBLESHOOTING
3. If the status indicator is blinking, the Controller is in lock-out mode
and will not accept remote commands. Activate the door from the
pushbutton wall console then check that the status indicator stops
blinking.
KEEP AWAY FROM SMALL CHILDREN. IF BATTERY IS SWALLOWED, PROMPTLY SEE A DOCTOR.
DO NOT TRY TO RECHARGE THIS BATTERY. DISPOSAL OF USED BATTERIES MUST BE MADE IN
ACCORDANCE WITH THE WASTE RECOVERY AND RECYCLING REGULATIONS IN YOUR AREA.
FLASH
GARAGE
DOOR
OPENER
BE SURE THE CONTROLLER
IS CLEAR OF ALL MOVING
PARTS OF THE GARAGE DOOR
9. OPERATION NOTES
BE SURE WIRES ARE
CLEAR OF ALL MOVING
PARTS OF THE GARAGE
DOOR AND OPENER
FLASH
FLASH
PU
SH
PU UTT
SH
BU N
TT
ON
USE THE BOLTS AND NUTS
SUPPLIED TO ATTACH THE
BRACKET TO A SECURE
STRUCTURE
THE DOOR OPENER AND OPEN
OR CLOSE THE DOOR
4 THE IRIS WEB PAGE OR MOBILE
INDENT
THE BRACKET SNAPS ONTO
INDENTS ON EITHER SIDE OR
ON THE END OF THE CONTROLLER
FLASH FOR FIVE SECONDS BEFORE
THE DOOR MOVES
2. Make sure that the Controller’s
connection wires are connected
to the proper terminals on the
garage door opener. Trace the
wires from the garage door
opener’s pushbutton wall console
to the door opener. This is where
the Controller’s connection wires
should be connected to.
2. Make sure the battery pull tab has
been removed from the tilt sensor.
3. Replace the battery in the tilt sensor.
Linear LLC (the Company) warrants to the original purchaser that products delivered hereunder will be
free of defects in materials and workmanship for a period of one (1) year from the date of purchase.
The Company within said period shall at its option, either repair or replace free of charge, any product
or part thereof found, upon the Company’s inspection, to be so defective, and will return the repaired or
replaced product to the purchaser at Company’s expense.
All products returned for warranty service require a Return Product Authorization Number (RPA#).
For warranty service, shipping instructions, and an RPA#, contact Linear Technical Services at
1-855-546-3351. Devices must be sent to the Company at owner’s expense and be accompanied with
statement of defect and proof of purchase.
This warranty is conditioned on the following:
1. The Company must be notified within one year of purchase and have been given the opportunity of
inspection by return of any alleged defective product free and clear of all liens and encumbrances to
the Company or its distributor; and
2. The product must not have been abused, misused or improperly maintained and/or repaired during
such period; and
3. Such defect has not been caused by corrosion or exposure to other than ordinary wear and tear.
THE COMPANY MAKES NO OTHER WARRANTY OR REPRESENTATION OF ANY KIND
WHATSOEVER INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.
The Company’s maximum liability hereunder is limited to the purchased price of the product. In no event
shall the Company be liable for any consequential, indirect, incidental or special damages of any nature
arising from the sale or use of the product, whether based in contract, tort, strict liability or otherwise.
Note: Some states do not allow limitations on incidental or consequential damages or how long an implied
warranty lasts, so that the above limitations may not fully apply. This warranty gives specific legal rights
and you may also have other rights which may vary from state to state.
This device complies with FCC Part 15 and Canada Rules and Regulations. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire
de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
Copyright © 2014 Linear LLC
235686 X21

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Title                           : 235686A GD00Z-1 Instructions IRIS.indd
Creator                         : Copyright © 2014 Linear LLC
Create Date                     : 2014:01:23 08:31:38-08:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2014:01:23 08:32:02-08:00
Metadata Date                   : 2014:01:23 08:32:02-08:00
Producer                        : Acrobat Distiller 10.1.9 (Windows)
Keywords                        : 
Document ID                     : uuid:1a636535-1d24-4746-bbc1-05139c0ee6fb
Instance ID                     : uuid:abb387cd-070a-4a52-89a4-e095106fb769
Startup Profile                 : Print
Page Count                      : 2
Author                          : Copyright © 2014 Linear LLC
Warning                         : [Minor] Ignored duplicate Info dictionary

EXIF Metadata provided by EXIF.tools