Nortek Security and Control 00120 Key Fob User Manual 236443A indd
Nortek Security & Control LLC Key Fob 236443A indd
User Manual
SW-ATT-FOB2 Installation Instructions
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules and Industry Canada license exempt RSS standard(s). Operation is
subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Any changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Les changements ou modifi cations non approuvés expressément par la partie responsable de la conformité pourrait
annuler l’autorité de l’utilisateur à faire fonctionner l’équipement.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L´exploitation est autorisée aux deux conditions suivantes: (1) l´appareil ne doit pas produire de brouillage, et (2)
l´utilisateur de l´appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d´en
compromettre le fonctionnement.
Product Description
The AT&T model number SW-ATT-FOB2 is a proprietary four-button key fob that
reports to the Digital Life Control Panel (DLC). The key fob includes a two-way
915 MHz band radio transceiver that communicates with the DLC.
Batteries are pre-installed in the SW-ATT-FOB2. The key fob is ready to use right
out of the box.
Key Fob Button Functions
The key fob supports the following functions:
ARM-AWAY, ARM-STAY, ARM-INSTANT and DISARM.
For details on each mode, please refer to the online help.
Key Fob LED Indicator
When a button is pressed on the key fob, the 2-color LED indicator at the top of the
key fob will light to display the status of the key fob and the system.
• When the system is disarmed, the LED will blink green for 2 seconds, then light green
for 2 seconds.
• When the system is being armed, with all the sensors secure (closed), the LED will
blink green for 2 seconds, then light red for 2 seconds.
• When the system is armed, with any open sensors bypassed, the LED will light green
with red fl ashes for 2 seconds, then light red for 2 seconds.
• If the key fob is activated while the batteries are low, the LED will blink red for 2
seconds. No arming or disarming will occur. The key fob batteries need replacing.
Discovering and Registering the Key Fob
Follow these steps to discover and register the SW-ATT-FOB2 key fob with the
customer’s DLC:
1. Use the Digital Life Direct (DLD) Web tool to place the DLC into Discovery Mode.
2. Make the SW-ATT-FOB2 discoverable by pressing and holding all four (4)
buttons simultaneously. The LED will slowly blink red during discovery. The
LED will turn solid red for 15 seconds if discovery successfully completes. The
LED will blink red fast for 15 seconds if discovery fails.
3. Confi rm in DLD that the SW-ATT-FOB2 key fob has been discovered by the DLC.
4. If desired, edit the key fob’s name and/or location in DLD.
5. Use the DLD Web tool to place the DLC into Test Mode then test the key fob. Specifi cations
• Dimensions: 2.25” x 1.27” x .46” (57.4 x 32.3 x 11.7 mm)
• Weight: .81 oz (23 g)
• Operating Temperature: 14° to 131°, 0° to 49° C (UL SPECS)
• Operating Rel. Humidity: 5 to 85%, non-condensing
• Operating Frequency: 915 MHz band
• Battery: 3V CR2025, Lithium Batteries, two required.
• Low Battery Report Level: 2.2 Volts
ARM
AWAY
ARM
STAY
DISARM
ARM
INSTANT
2-COLOR LED
INDICATOR
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,SW-ATT-FOB2; LINEAR P/N: 236443 X6 INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500” x 11.000”; SCALE: 1-1
Copyright © 2014 Linear LLC 236443 X6
Figure 1. Key Fob Features
Figure 2. Key Fob Battery Replacement
1
TWIST COIN IN
SLOT TO OPEN
TRANSMITTER
2
CAREFULLY REMOVE
RETAINING SCREW
AND LIFT OUT BOARD
3
REPLACE BATTERIES
WITH TWO TYPE CR2025
LITHIUM BATTERIES
PLUS SIDE DOWN
CR2025
4
REVERSE STEPS TO
REASSEMBLE TRANSMITTER
BE CAREFUL NOT TO
DROP SCREW ON BOARD
KEEP BATTERIES AWAY FROM SMALL CHILDREN. IF BATTERIES ARE
SWALLOWED, PROMPTLY SEE A DOCTOR.
DO NOT TRY TO RECHARGE THESE BATTERIES.
DISPOSAL OF USED BATTERIES MUST BE MADE IN ACCORDANCE WITH THE
WASTE RECOVERY AND RECYCLING REGULATIONS IN YOUR AREA.
SIDE
SIDE
CR2025
Replacing the Batteries
The SW-ATT-FOB2 key fob includes low battery reporting. When the system or
key fob indicates a low battery condition, replace the two batteries with Duracell
DL2025, or Maxell, Panasonic, GP, or Renata (CR2025) batteries.
Follow these steps to replace the batteries:
1. Remove the top cover by inserting a coin in the slot located at the bottom of
the key fob and turn it ninety (90) degrees.
2. Use a small Phillips Head screwdriver to remove the screw located in the
center of the printed circuit board. (Do not discard the screw.)
3. Remove the printed circuit board.
4. Remove the two depleted batteries and dispose of them as required by local laws.
5. Insert the replacement batteries, CR 2025, paying careful attention to the
batteries polarity.
✓NOTE: The (+) side of the batteries should be facing down.
6. Replace the printed circuit board with the side with the two large circles
facing the batteries.
7. Secure the printed circuit board by screwing it in place with the screw
previously removed using a small Phillips Head screwdriver.
8. Snap the cover of the key fob transmitter over the base assembly.
9. Verify that the key fob is working properly by arming and disarming the system.