Nortek Security and Control 00127 Door Chime Button User Manual 236839A indd

Nortek Security & Control LLC Door Chime Button 236839A indd

User Manual

Download: Nortek Security and Control 00127 Door Chime Button User Manual 236839A indd
Mirror Download [FCC.gov]Nortek Security and Control 00127 Door Chime Button User Manual 236839A indd
Document ID2555140
Application IDMXjJTRjP0XLswaKDZT9GBw==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize8.85kB (110574 bits)
Date Submitted2015-03-13 00:00:00
Date Available2015-03-13 00:00:00
Creation Date2014-12-05 16:46:50
Producing SoftwareAcrobat Distiller 10.1.12 (Windows)
Document Lastmod2015-02-03 16:27:51
Document Title236839A.indd
Document CreatorPScript5.dll Version 5.2.2
Document Author: Copyright © 2015 Linear LLC

PRINTER’S INSTRUCTIONS:
INSTR,INSTL,SW-ATT-DB; LINEAR P/N: 236839 X2; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500” x 11.000”; SCALE: 1-1
SW-ATT-DB
Installation Instructions
Discovering and Registering the Transmitter
DRAIN
HOLE
PUSHBUTTON
SW-ATT-DB Door Chime Button/Sensor
Product Description
The AT&T model number SW-ATT-DB is a fully supervised proprietary
two-way 915 MHz door chime button transmitter designed to signal the
DLC and ring a local door chime when its pushbutton is pressed.
Two terminals in the transmitter connect to the existing household door
chime wires. The transmitter is powered by the voltage present on the
door chime button wires. When the transmitter’s pushbutton is pressed,
the two terminals provide a circuit closure that activates the household
door chime.
SIGNAL
INDICATOR
LEARN
BUTTON
Follow these steps to discover and register the SW-ATT-DB sensor with
the customer’s system:
1. Use the Web tool to place the system into Discovery Mode.
2. Make the SW-ATT-DB discoverable by pressing and holding the
sensor’s LEARN button for three seconds. The signal indicator will
slowly blink during discovery. The LED will turn solid for 15 seconds
if discovery successfully completes. The LED will blink fast for
15 seconds if discovery fails.
3. Confirm that the SW-ATT-DB sensor has been discovered by the
system.
4. If desired, edit the sensor’s name and/or location in the system.
5. Attach the sensor to the mounting plate by inserting the two tabs
on the bottom end of the mounting plate into the terminal end of the
sensor’s top case, then snap the case closed.
6. Use the Web tool to place the system into Test Mode then test the
sensor by pressing the sensor’s pushbutton. The existing household
doorbell should also ring when the sensor’s pushbutton is pressed.
Specifications
•
•
•
•
•
•
•
Operating Temperature: -25° to 55° C
Operating Frequency: 915 MHz
Dimensions: 2.75 x 1.17 x 0.63 in. (6.98 x 2.97 x 1.00 cm)
External Input: 16VAC Class 2 transformer
Weight: approx. 1 oz.
Housing Material: ABS plastic
Color: White
CONNECTION
TERMINALS
SW-ATT-DB Component Locations
Installing the Transmitter
The transmitter typically mounts in the location that replaces the current
hardwired door chime pushbutton.
Follow these steps to install the transmitter:
1. Remove the current hardwired door chime pushbutton. Disconnect
the two door chime wires and prepare them to connect to the new
transmitter.
2. Twist a small screwdriver in the slot on the end of the transmitter
and remove the mounting plate.
3. Route the door chime wires through the mounting plate. Be sure
the arrow on the mounting plate points up and attach the mounting
plate to the surface with the two screws provided.
4. Connect the two door chime wires to the two screw terminals
inside the transmitter. Polarity is not important.
Wait to close the sensor until after the discovery process.
MOUNTING
PLATE
UP
ARROW
MOUNTING
SCREWS
EXISTING
DOOR CHIME
WIRES
Door Chime/Sensor Mounting
Copyright © 2014 Linear LLC
FCC Compliance Statement
This device complies with FCC Rules and Regulations as Part 15 devices as well as Industry Canada license exempt
RSS Rules and Regulations. Operation is subject to the following two (2) conditions: This device may not cause harmful
interference. This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
236839 X2

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Author                          : Copyright © 2015 Linear LLC
Create Date                     : 2014:12:05 16:46:50-08:00
Modify Date                     : 2015:02:03 16:27:51-08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Acrobat Distiller 10.1.12 (Windows)
Keywords                        : 
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2015:02:03 16:27:51-08:00
Format                          : application/pdf
Title                           : 236839A.indd
Creator                         : Copyright © 2015 Linear LLC
Document ID                     : uuid:03f3457d-17c0-476c-89cf-9af4ec8ecc2e
Instance ID                     : uuid:fb7dab50-5035-4654-bee0-fcf7a7cf04ca
Page Count                      : 1
EXIF Metadata provided by EXIF.tools
FCC ID Filing: EF400127

Navigation menu