Nortek Security and Control 00128 Garage Door Opener Remote Command Transceiver User Manual 236956B GD00Z 4 GENERIC Instructions indd

Nortek Security & Control LLC Garage Door Opener Remote Command Transceiver 236956B GD00Z 4 GENERIC Instructions indd

User Manual

GD00Z-4GARAGE DOOR OPENERREMOTE COMMANDTRANSCEIVERwith TILT SENSORInstallation Instructions➊ PRODUCT DESCRIPTION ➋ SAFETY NOTES➌ PRODUCT COMPONENTS ➍ TILT SENSOR INSTALLATION AND BATTERY ➎ PAIRING (INCLUDING) WITH THE SYSTEMPRINTER’S INSTRUCTIONS:INSTR,INSTL,GD00Z-4 - P/N: 236956 AX4 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - TOL. +/-.125" - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 1 OF 2 WARNING This operator system is equipped with an unattended operation feature. This door could move unexpectedly. NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR! WARNING This system can be installed on sectional type (roll up) doors only per (UL-325). DO NOT INSTALL ON ONE-PIECE DOORS! WARNING Do not install the Remote Command Transceiver on garage door operators manufactured prior to 1993 (models without an operational safety beam entrapment detection system). WARNING The Remote Command Transceiver must be mounted in the garage, in sight of the garage door, where the visual and audible movement warning indicators can be clearly seen and heard.GD00Z-4POWERINPUTJACKWARNINGLIGHTLINKBUTTONCONNECTIONWIRES MOUNTING SCREWSAND ANCHORSFOR GD00Z-4POWERSUPPLYTILTSENSORSTATUSINDICATOROPTIONALADJUSTABLEGD00Z-4 MOUNTINGBRACKETPOWERSUPPLYRETAININGBRACKETSCREWS ANDMOUNTING TAPEFOR TILT SENSORSCREW ANDMOUNTING HARDWAREFOR ADJUSTABLEBRACKET SCREW FORPOWER SUPPLYBRACKETWIRETIESTO INCLUDE THE GD00Z-4INTO YOUR CONTROLLER12WALLOUTLETPOWERSUPPLY POWERINPUTJACKLINKBUTTONGD00Z-4Press and release the link buttonon the GD00Z-4.Note: Plug in the GD00Z-4near your Z-Wave Controllerfor these stepsPlace your Z-Wave Controller intoDiscovery or Include mode.TO EXCLUDE THE GD00Z-4FROM YOUR CONTROLLERConfirm that the GD00Z-4 wasrecognized by your Z-Wave Controller.Refer to your Z-Wave Controllersinstructions for additional informationon including devices.312Press and release the link buttonon the GD00Z-4.Place your Z-Wave Controller intoExclude mode.Confirm that the GD00Z-4 wasexcluded by your Z-Wave Controller.Refer to your Z-Wave Controllersinstructions for additional informationon excluding devices.3CR2032PLUS SIDE UP !!!The system will notify youwhen the battery is low,replace the battery witha type CR2032 coin cellInsert thebatteryinto thetransmitterTo open the case, twista small screwdriverin case slot SLOT Use double sided tape orthe two mounting screws supplied(drill 1/16" pilot holes if required)POST ONBOTTOM"UP"ARROWSSnap the sensor ontothe mounting plateTo activate the tilt sensor,remove the battery protection pull strip2ARROWS ON PLATE& SENSOR POINT UPLOW BATTERY REPLACEMENT1213Attach the mounting plateto the top panel of the doorUSA & Canada (800) 421-1587 & (800) 392-0123(760) 438-7000 - Toll Free FAX (800) 468-1340www.nortekcontrol.comGD00Z-4 Overview• A garage door opener remote command transceiver with built-in Z-Wave technology.• Allows remote operation of a garage door opener using Z-Wave controllers.• Acts as a Z-Wave repeater to improve communications within the Z-Wave mesh network.GD00Z-4 Summary of Operation• GD00Z-4 connects to the garage door opener’s pushbutton wall console terminals.• A wireless tilt sensor mounts on the garage door and reports the door’s position to the GD00Z-4.• GD00Z-4 responds to Z-Wave commands from Z-Wave controllers to open or close the garage door.• A warning indicator light fl ashes and a beeper sounds for 5 seconds before the door begins to move.• If the door does not completely open or close, a second open or close command can be sent after 30 seconds.• If the door does not completely open or close after the second attempt, the GD00Z-4 operation is suspended until a local garage door pushbutton is activated.Z-Wave Information• Z-Wave® is a registered trademark of Sigma Designs Inc. and/or its subsidiaries.• Z-Wave is an Interoperable two-way RF mesh networking technology designed for use with a Z-Wave gateway/controller and other Z-Wave enabled devices.• Replication is the process of copying or transferring your Z-Wave network from one controller to another.• This is a Security enabled Z-Wave product and must be used with a Security enabled Z-Wave controller in order to fully utilize this product. As such, this device will not respond to Basic CC commands.• ASSOCIATION: The GD00Z-4 supports 1 Group with 1 Node. Group 1 must be assigned the Node ID of the controller to which unsolicited notifi cations from the GD00Z-4 will be sent. The Z-Wave controller should set this association automatically after inclusion.APPLIANCE CONTROLS
➏ GD00Z-4 MOUNTING ➐ GD00Z-4 CONNECTIONS ➑ SYSTEM OPERATION➒ OPERATION NOTES1. The warning light will fl ash and the warning beeper will sound for fi ve seconds before the door opener is activated. STAY CLEAR OF THE DOOR, AND DOOR OPENER. THEY ARE ABOUT TO MOVE!2. If the door does not completely open or close after remote activation, the GD00Z-4 will allow user to try to operate the door one more time. If the second attempt fails, the GD00Z-4 will go into lock-out mode. See Note #3.3. If the GD00Z-4 is in lock-out mode and will not accept remote commands, activate the door from the pushbutton wall console.4. Once the GD00Z-4 has initiated the movement of the garage door, another command cannot be sent for 30 seconds. This eliminates the chance of “bouncing” the garage door and possibly damaging the garage door opener.➓ TROUBLESHOOTINGPROBLEM POSSIBLE CAUSE CORRECTIVE ACTIONUnable to include in Z-Wave network.GD00Z-4 was not properly excluded from a previous Z-Wave network.1. Reset the GD00Z-4 by pressing the LINK button 5 times. A quick beep followed by a longer beep will indicate the reset.The GD00Z-4 does not fl ash or beep when activated.No power to the GD00Z-4.1. Make sure the power supply is plugged in securely to a live outlet.2. Make sure the power cord is plugged in securely to the GD00Z-4.The GD00Z-4 fl ashes and beeps when activated but the door does not move.Obstruction blocking the door or incorrect wiring.1. Make sure that there are no obstacles preventing the door from moving.2. Make sure that the GD00Z-4 connection wires are connected to the proper terminals on the garage door opener. Trace the wires from the garage door opener’s pushbutton wall console to the door opener. This is where the GD00Z-4 connection wires should be connected.Garage door opens or closes, but the status does not change on the Z-Wave Controller.The tilt sensor signal is not being received by the GD00Z-4.1. Make sure the tilt sensor is mounted correctly on the garage door, with the arrow pointing up.2. Make sure the battery pull tab has been removed from the tilt sensor.3. Replace the battery in the tilt sensor.NORTEK SECURITY & CONTROL LIMITED WARRANTY This Nortek Security & Control product is warranted against defects in material and workmanship for twelve (12) months. This warranty extends only to wholesale customers who buy direct from Nortek Security & Control or through Nortek Security & Control’s normal distribution channels. Nortek Security & Control does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Nortek Security & Control LLC for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profi t, or cost of removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for fi tness, are valid only until the warranty expires. This Nortek Security & Control LLC Warranty is in lieu of all other warranties express or implied.All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Nortek Security & Control Returns at 1-855-546-3351 for an RPA# and other important details.REGULATORY NOTICESChanges or modifi cations not expressly approved by the manufacturer could void the user’s authority to operate the equipment.Les changements ou modifi cations non approuvés expressément par la partie responsable de la conformité pourrait annuler l’autorité de l’utilisateur à faire fonctionner l’équipement.This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.• Reorient or relocate the receiving antenna• Increase the separation between the equipment and receiver• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected• Consult the dealer or an experienced radio/TV technician for helpThis Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.PRINTER’S INSTRUCTIONS:INSTR,INSTL,GD00Z-4 - P/N: 236956 AX4 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - TOL. +/-.125" - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 2 OF 2The GD00Z-4 typicallymounts on the ceilingnear the opener andthe power outletTilt sensormounted onthe top panelof the doorTHE GD00Z-4 CAN ALSO BE ATTACHED TO THE OPENER'SHARDWARE USING THE ADJUSTABLE MOUNTING BRACKETTHE GD00Z-4 WARNINGLAMP MUST BE VISIBLE INALL DOOR POSITIONS3/16" HOLESFOR ANCHORSThe optional adjustablemounting bracket fits3 ways on the GD00Z-4The bracket snaps ontoindents on either side oron the end of the GD00Z-4Securebracketwith screwUse the four screwsand anchors to mountthe GD00Z-4 abovethe openerINDENTINDENTUse the bolts and nuts suppliedto attach the bracket to a securestructureBE SURE THE GD00Z-4IS CLEAR OF ALL MOVINGPARTS OF THE GARAGE DOORAND THE WARNING LAMP ISNOT OBSTRUCTEDINDENT1A2AREMOVE POWER FROM THEGARAGE DOOR OPENERBEFORE CONTINUING! WARNING !1PUSHBUTTONPUSHBUTTONGARAGEDOOROPENERConnect the GD00Z-4 connectionwires to the pushbutton wall consoleterminals on the garage door opener.The terminals may be named "PWC", "WC","PB", "PUSHBUTTON", or "RED and WHITE". Terminal names and locations vary by model.DO NOT DISCONNECTANY WIRES CURRENTLYCONNECTED TO THEGARAGE DOOR OPENER !!!Remove the screw from 120 VACoutlet faceplate. Secure the retainingbracket to the faceplate with the providedscrew. Snap the power supply into thebracket while plugging into the outlet.USE WIRE TIES TO SECUREEXCESS WIRING CLEAROF ALL MOVING PARTSOF THE GARAGEDOOR AND OPENEREither wire canconnect to eitherterminalPlug the power cordinto the power inputjack on the GD00Z-4213FLASHFLASHFLASHBEEPBEEPBEEPUse your Z-Wave Controller toactivate your garage door openerThe GD00Z-4 will activatethe door opener and openor close the doorSTAY CLEAROF THE DOOR !!!3The GD00Z-4 will beep andflash for five seconds beforethe door moves45Restore power to yourgarage door opener1To synchronize the system,use the garage door opener'spushbutton to manually openand close the door2STAY CLEAROF THE DOOR !!!Copyright © 2015 Nortek Security & Control LLC 236956 AX4 GD00Z-4 Specifi cations Power Supply: Input: 120 VAC, 0.8 A Output: 12 VDC, 2 A Operating Temperature: -4º—122° F (-20º—50° C) Audible Alarm: 45 db @ 10 feet Strobe: 360 Lumens Communications: Z-Wave (908.4 MHz) Mounting: Screws and anchors to the ceiling, or bracket to the opener’s hanging hardware Tilt Sensor Specifi cations Power Supply: Type CR2032 Coin Cell Battery Operating Temperature: -4º—122° F (-20º—50° C) Battery Life: 24 Months (typical) Communications: Proprietary 345 MHz Range: 100 feet line-of-sight to GD00Z-4 Mounting to Garage Door: Double-sided tape or two mounting screws(Specifi cations subject to change without notice)NOTICE TO USERS IN CALIFORNIA - CR COIN CELL LITHIUM BATTERY INFORMATION: THIS PRODUCT CONTAINS A CR COIN CELL LITHIUM BATTERY WHICH CONTAINS PERCHLORATE MATERIAL - SPECIAL HANDLING MAY APPLY - SEEwww.dtsc.ca.gov/hazardouswaste/perchlorateKEEP AWAY FROM SMALL CHILDREN. IF BATTERY IS SWALLOWED, PROMPTLY SEE A DOCTOR. DO NOT TRY TO RECHARGE THIS BATTERY. DISPOSAL OF USED BATTERIES MUST BE MADE IN ACCORDANCE WITH THE WASTE RECOVERY AND RECYCLING REGULATIONS IN YOUR AREA.

Navigation menu