Northfield Telecommunications d b a Advanced Wireless Communications HD-1000V2 Two-Way Radio User Manual 1

Northfield Telecommunications, Inc. d/b/a Advanced Wireless Communications Two-Way Radio 1

user manual

HD-1000V2
GENERAL/概述 INTRODUCTIONSCOPE OF THIS MANUALfamiliar with similar types of commercial grade communicationsequipment. It contains all required service information for theequipment and is current as of the publication date.ChangesBulletins or Manual Revisions. These are issued as required.ORDERING REPLACEMENT PARTSWhen ordering replacement parts or equipment information,applies to all parts: components, kits, or chassis. If the partcomponent for proper identification.PERSONAL SAFETYThe following precautions are recommended for personal safety: • DO NOT transmit until all RF connectors are verified secure and any open connectors are properly terminated. • blasting caps or in an explosive•This equipment should be serviced by a qualified technician only.SERVICEThis radio is designed for easy servicing. Refer to the schematicdiagrams, printed circuit board views, and alignment procedurescontained within.0.5W/1W0.5W/1W引言 本手册的范围 本手册是提供给熟悉通信专业并且具有维修经验的技术人员 使用的。 替换零件的订购 当订购替换零件或设备信息时，应注明完整的零件识别号码。 所有的零件均有识别号码：元件、组件或机壳。如果不知道 零件的号码，为了正确地识别，必须注明此元件所属的机壳 或组件的号码，并对元件进行充分的说明。 个人安全 为了个人的安全，请注意下列事项： •在没有认真核实所有射频插头之前或有任何一个打开的插头 没有连接到响应端子上的情况下，均不要发射。 •在电爆管附近或在易燃性气体环境中，必须关掉电源，不要 操作本设备 •本设备只应该由有资格的技术人员来维修。 维修服务 为了便于维修本设备，建立了完整的维修服务体系，提供了 包括原理图、印刷线路图和调整步骤在内的资料供参考。 信道数量 射频输出功率 RF Power OutputNumber of channelsThis manual is intended for use by experienced technicianswhich may occur after publication are covered by either Service 它包括了维修该设备所 需要的全部资料和现行公布 后可能发生变动，如果需要，可以使用《维修 the full part identification number should be included.Thisnumber is not known, include the chassis or kit number ofSHUT OFF and DO NOT operate this equipment near electricalwhich it is a part, and a sufficient description of the required的数据。在出版 通报》或《手册修订本》进行补充。 199 199
SAFETYTRAINING INFORMATION Your radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the “General Population” in an uncontrolled environment. This radio has been tested and complies with the FCC RF exposure limits for “Occupational Use Only”. In addition, your radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans:  FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields.  American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.  American National Standards Institute (C95.3-1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields– RF and Microwave.  The following accessories are authorized for use with this product. Use of accessories other than those (listed in the instruction) specified may result in RF exposure levels exceeding the FCC requirements for wireless RF exposure. To ensure that your expose to RF electromagnetic energy is within the FCC allowable limits for occupational use, always adhere to the following guidelines:  DO NOT operate the radio without a proper antenna attached, as this may damaged the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specifically authorized by the manufacturer for use with this radio.  DO NOT transmits for more than 50% of total radio use time (“50%duty cycle”). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when the “TX indicator” lights red. You can cause the radio to transmit by pressing the “PTT” switch.
 ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body when transmitting and only use the belt-clip which is listed in instructions when attaching the radio to your belt, etc., to ensure FCC RF exposure compliance requirements are not exceeded. To provide the recipients of your transmission the best sound quality, hold the antenna at least 5 cm (2 inches) from your mouth, and slightly off to one side. The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to as-sure that this radio operates with the FCC RF exposure limits of this radio. Electromagnetic Interference/Compatibility During transmissions, your radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites. Occupational/Controlled Use The radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver SAVE THIS INSTRUCTION MANUAL- This instruction manual contains important operating instructions for the Two-Way Radio EXPLICIT DEFINITIONS WORD DEFINITION WARNING Personal injury, fire hazard or electric shock may occur. CAUTION Equipment damage may occur. NOTE If disregarded, inconvenience only. No risk of personal injury, fire or electric shock.
OPERATING NOTES  When transmitting with a portable radio, hold the radio in a vertical position with its microphone 5 to 10 cm (2 to 4 inches) away from your mouth. Keep the antenna at least 2.5 cm (1 inch) from your head and body.  If you wear a portable two-way radio on your body, ensure that the antenna is at least 2.5 centimeters (1 inch) from your body when transmitting. PRECAUTIONS WARNING! NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm (2 to 4 inches) away from the lips and the transceiver is vertical. WARNING! NEVER operate the transceiver with a headset or other audio accessories at high volume levels. CAUTION! NEVER short the terminals of the battery pack. NEVER connect the transceiver to a power source other than the Battery listed below Such a connection will ruin the transceiver. DO NOT push the PTT when not actually desiring to transmit. AVOID using or placing the transceiver in direct sunlight or in areas with temperatures below –30°C (–22°F) or above +60°C (+140°F). DO NOT modify the transceiver for any reason. MAKE SURE the flexible antenna and battery pack are securely attached to the transceiver, and that the antenna and battery pack are dry before attachment. Exposing the inside of the transceiver to water will result in serious damage to the transceiver. BE CAREFUL! The series transceivers employ waterproof construction, which corresponds to IPX7 of the international standard IEC 60529 (2001), 1 m depth for 30 minutes. However, once the transceiver has been dropped, waterproofing cannot be guaranteed due to the fact that the transceiver may be cracked, or the waterproof seal damaged, etc. The use of non-Advanced battery packs/chargers may impair transceiver performance and invalidate the warranty. FCC CAUTION: Changes or modifications to this device, not expressly approved by Manufacturer, could void your authority to operate this transceiver under FCC regulations.
910
MODESUSER MODE PC MODE模式 用户模式 PC模式 MODESUser modePC modePC modePower ON PROCEDUREUsed for communication between the radioand a PCHow to enter each mode MODESPC MODEPrefaceThe HD-1000 transceiver can be programmed using a personalThe programming software can be used on an IBMCaution:When removing or installing the programming cable,firstswitch off the radio power.Additionally, be sure to disable the VOX function, ifit’s enabled, as it can sometimes activate from connectionnoise.Connection procedure1. Connect the HD-1000 to the personal Computer using theinterface cable.2. When the POWER is switched ON, you can enter user mode.Programming software descriptionThe software allows a user to program the HD-1000 radios via the • Programming with IBM PCIf data is transferred to the transceiver from a PC with the software,the destination data (basic radio information) for each set can be modified. For normal use.FUNCTION用户模式计算机模式 Used for communication between the radioand a PC用于普通操作 功能 模式类型 User mode Receiver commands from PC 模式类型 操作步骤 用户模式 计算机模式 打开电源开关 从计算机接收命令 software.PC or compatible. Fig-1 shows the setup of a PC for programming.programming interface cable.计算机模式前言 通过个人电脑，使用编程电缆和编程软件，对对讲机HD-1000进行编程设置。图1表示一台IBM计算机的编程设置过程。 注意 当拔除或者插入编程电缆首先关闭对讲机电源。另外，确保声 控功能已关闭，如果声控被激活，可能有时会开启连接噪音。 连接步骤1.使用接口电缆将HD-1000与个人电脑连接。2.当电源开关打开，可以进入用户模式。编程软件说明该软件允许用户经由编程接口电缆对HD-1000进行编程设定。使用IBM计算机编程 如果从使用软件的IBM计算机将数据发送到手持机，设定的目的 数据（基本通信参数）均可被修改。 computer, A programming interface cable and programming
DISASSEMBLY FOR REPAIR/维修时拆卸部分Separating the case assembly from the chassis1. Remove the knob 1 and the round nut 22. Remove the six screws 3 and 43. Expand the right and left sides of the bottomit from the case assembly 5. 4. Taking care not to cut the speaker lead 7,Remove the screws 8 and drop-out line,of the case assembly, lift the chassis,andopenand lift从底座上分离外壳 1.取下旋扭 1和环形螺母2.取下六颗螺钉3.掀开外壳底部的左右两侧，取下底座，并外壳中取出 24354.小心不要折断扬声器引线 7，拆下底座和外壳。 底座从主板上分离 然后取下主板.，8removethe chassis and case assembly.the first unit off.取下螺钉Separating the chassis from the unit和
FCC ID: Q9SHD-1000V2 IC: 4651A-HD1000V2 NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. 

Navigation menu