Novatel Wireless GSM2428 GSM/ GPRS Personal Tracker User Manual GSM2428

Novatel Wireless Inc. GSM/ GPRS Personal Tracker GSM2428

User Manual

  - 1 -           Mini MT   User Guide     GSM2428UG001   Version:1.01     13 June, 2011
  - I - General TERMS OF USE OF NEW MATERIALS - PLEASE READ CAREFULLY  From  time  to  time,  Enfora,  in  its  sole  discretion,  may  make  available  for  download  on  its  website (www.enfora.com),  or  may  transmit  via  mail  or  email,  updates  or  upgrades  to,  or  new  releases  of,  the firmware,  software  or  documentation  for  its  products  (collectively,  'New  Materials').  Use  of  such  New Materials is subject to the terms and conditions set forth below, and may be subject to additional terms and conditions as set forth in Enfora's Technical Support Policy (posted on its website) and/or any written agreement between the user and Enfora.  All  New  Materials  are  provided  AS  IS.  Enfora  makes  no  warranty  or  representation  with  respect  to  the merchantability, suitability, functionality, accuracy or completeness of any such New Materials. The user of such  New Materials  assumes  all risk  (known  or unknown) of  such  use.  Enfora  reserves  all  rights  in  such New  Materials.  The  user  shall  have  only  a  revocable  and  limited  license  to  use  such  New  Materials  in connection  with  the  products  for  which  they  are  intended.  Distribution  or  modification  of  any  New Materials without Enfora's consent is strictly prohibited.  IN  NO  EVENT  WILL  ENFORA  BE  RESPONSIBLE  FOR  ANY  INCIDENTAL,  INDIRECT,  CONSEQUENTIAL  OR SPECIAL DAMAGES AS A RESULT OF THE USE OF ANY NEW MATERIALS. ENFORA'S MAXIMUM LIABILITY FOR ANY CLAIM BASED ON THE NEW MATERIALS SHALL NOT EXCEED FIFTY U.S. DOLLARS ($50). Copyright © 2011 Enfora, Inc. All rights reserved. Complying with all applicable copyright laws is the responsibility of the user. Without limiting the rights under copyright, no part of this document may be reproduced, stored in  or  introduced  into  a  retrieval  system,  or  transmitted  in  any  form  or  by  any  means  (electronic, mechanical,  photocopying,  recording  or  otherwise),  or  for  any  purpose,  without  the  express  written permission of Enfora, Inc.  Enfora  and the  Enfora logo are either  registered trademarks or  trademarks of  Enfora, Inc. in the United States.  251 Renner Pkwy  Richardson, TX 75080 USA  Phone: (972) 633-4400  Fax: (972) 633-4444  Email: info@enfora.com  www.enfora.com
  - II - Warranty Information [Revised: 11/11/2010]  This warranty applies to (a) products sold directly by Enfora, unless a different warranty is specified in a written  agreement  between  Enfora  and  the  purchaser;  and  (b)  products  sold  to  end  users  through  a distributor  authorized by Enfora, but only where the  authorized  distributor does not provide  a separate warranty  on  such  products,  and  Enfora  has  agreed  to  provide  this  warranty  to  such  end  users.  If  you purchased the product from an authorized distributor, please check whether this warranty from Enfora, or a separate warranty from the distributor, applies to your purchase. This warranty does not apply to any (i) accessories  or  batteries  for  the  products;  or  (ii)  demonstration  samples  or  prototypes  of  the  products. Unless otherwise provided in a written agreement between Enfora and the purchaser, all such accessories, batteries, samples or prototypes are provided by Enfora AS IS without any warranty of any kind.  Enfora  warrants  to  the  original  purchaser  of  the  product  from  Enfora  or  its  authorized  distributor  (as applicable) that, for a period of one (1) year from the date of shipment of the product from Enfora, the product  hardware  will  be  substantially  free  from  defects  in  material  or  workmanship  under  normal operation,  and  the  product  firmware  will  perform  substantially  in  accordance  with  the  product documentation provided by Enfora. Enfora does not  warrant that (a) the product hardware or firmware will  meet  the  purchaser's  requirements;  (b)  the  operation  of  the  product  hardware  or  firmware  will  be uninterrupted or error-free; or (c) the product, when integrated in, or combined with, other products or software  not  supplied  by  Enfora,  will  continue  to  perform  substantially  in  accordance  with  the  product documentation. This limited warranty is for the benefit of the original purchaser, and is not transferable.  During  the  warranty  period,  Enfora,  at  its  expense  and  in  its  sole  discretion,  will  repair  the  product,  or replace  the  product  with  a  corresponding  or  equivalent  product,  if  it  is  determined  to  have  a  covered defect, provided that the purchaser first notifies Enfora (directly or through its authorized distributor from which  the  product  was  purchased)  of  any  such  defect,  furnishes  Enfora  with  a  proof  of  purchase  (if required),  requests  and  obtains  a  return  merchandize  authorization  (RMA)  number  from  Enfora,  and returns the product under that RMA to Enfora (or, at Enfora's option, to its authorized distributor), with the shipping charges being prepaid by purchaser.If, upon reasonable examination of the returned product, Enfora does not substantiate the defect claimed by purchaser, or determines that the defect is not covered under this limited warranty, Enfora will not be required to repair or replace the product, but may instead reship the product to the purchaser (or, at Enfora's option, to its authorized distributor where the product can be made available to purchaser), in which case the purchaser shall be responsible for paying Enfora's cost  for  reshipping  the  product  to  purchaser  (or  to  Enfora's  authorized  distributor),  and  Enfora's  usual charges  for  unpacking,  testing,  and  repacking  the  product  for  reshipment  to  purchaser  (or  to  Enfora's authorized distributor). Purchaser shall bear the risk of loss or damage in transit to any product returned by purchaser to Enfora, or any returned product not found to be defective or covered under this warranty, and reshipped by Enfora to purchaser (or to Enfora's authorized distributor). In the event Enfora repairs or replaces a defective product covered by this limited warranty, the repaired or replacement product will be covered  under  this  limited  warranty  for  the  remainder  of  the  original  warranty  period  on  the  defective
  - III - product,  or  a  period  of  ninety  (90)  days,  whichever  is  longer.  If  Enfora  is  unable  to  repair  or  replace  a defective product covered by this limited warranty, Enfora will provide to purchaser a credit or a refund (at Enfora's  option)  of the original purchase price (excluding taxes  and  shipping  charges).  Any  returned  and replaced  product,  or  any  product  for  which  Enfora  has  furnished  a  credit  or  a  refund,  becomes  the property of Enfora.  Enfora shall not have any obligation to provide any firmware bug fixes, upgrades or new releases except as may be necessary to correct any covered defect of which purchaser notifies Enfora in writing during the warranty period. Enfora, from time to time and in its sole discretion, may make available for download on its  website  (www.enfora.com),  or  may  provide  via  email,  certain  firmware  bug  fixes,  upgrades  or  new releases for the product. Download and use of any such bug fixes, upgrades or new releases is subject to all of the applicable terms and conditions of Enfora's technical support policy as posted and updated on its website. Enfora shall have no obligation under this limited warranty for (a) normal wear and tear; (b) the cost of procurement of substitute products; or (c) any defect that is (i) discovered by purchaser during the warranty  period  but  for  which  purchaser  does  not  request  an  RMA  number  from  Enfora,  as  required above,  until  after  the  end  of  the  warranty  period,  (ii)  caused  by  any  accident,  misuse,  abuse,  improper installation, handling or testing, or unauthorized repair or modification of the product, (iii) caused by use of any  materials  not  supplied  by  Enfora,  or  by  use  of  the  product  other  than  in  accordance  with  its documentation, or (iv) the  result of  electrostatic discharge,  electrical  surge,  fire,  flood  or  similar causes. The  purchaser  (or  its  customers,  as  applicable)  shall  be  solely  responsible  for  the  proper  configuration, testing and verification of the Enfora product prior to deployment in the field, and for ensuring that any end  user  product  or  system  into  which  the  Enfora  product  is  integrated  or  incorporated  operates  as intended and meets the requirements of purchaser (or its customers). Enfora shall have no responsibility whatsoever  for  the  integration,  configuration,  testing,  verification,  installation,  upgrade,  support  or maintenance  of  any  such  end  user  product  or  system,  or  for  any  liabilities,  damages, costs  or  expenses associated therewith.  ENFORA'S SOLE RESPONSIBILITY AND PURCHASER'S SOLE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE FOR ENFORA TO REPAIR OR REPLACE THE PRODUCT (OR IF REPAIR OR REPLACEMENT IS NOT POSSIBLE, PROVIDE  A  CREDIT  OR  REFUND  OF  THE  PURCHASE  PRICE)  AS  PROVIDED  ABOVE.  ENFORA  EXPRESSLY DISCLAIMS  ALL  OTHER  WARRANTIES  OF  ANY  KIND,  EXPRESS  OR  IMPLIED,  INCLUDING  WITHOUT LIMITATION  ANY  IMPLIED  WARRANTIES  OF  NON-INFRINGEMENT,  MERCHANTABILITY,  SATISFACTORY PERFORMANCE AND FITNESS  FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ENFORA BE LIABLE FOR ANY INDIRECT, SPECIAL, EXEMPLARY, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING WITHOUT LIMITATION LOSS OR INTERRUPTION OF USE, DATA, REVENUES OR PROFITS) RESULTING FROM A BREACH OF THIS  WARRANTY  OR BASED ON  ANY OTHER LEGAL  THEORY, EVEN IF  ENFORA HAS BEEN  ADVISED  OF THE POSSIBILITY OR LIKELIHOOD OF SUCH DAMAGES.  Some  jurisdictions  may  require  a  longer  warranty  period  than  specified  above  and,  accordingly,  for products sold in those jurisdictions the applicable warranty period shall be extended as required under the laws  of  those  jurisdictions.  Furthermore,  some  jurisdictions  may  not  allow  the  disclaimer  of  implied warranties or the exclusion or limitation of incidental or consequential damages, so the above disclaimer, limitation or exclusion may not apply to products sold in those jurisdictions. This limited warranty gives the
  - IV - purchaser specific legal rights and the purchaser may have other legal rights that vary from jurisdiction to jurisdiction.  This  limited  warranty  shall  be  governed  by  the  laws  of  the  State  of  Texas,  United  States  of America, without regard to conflict of laws principles. This limited warranty shall not be governed in any respect by the United Nations Convention on Contracts for the International Sale of Goods. Regulatory Compliance FCC  FCC ID: MIVGSM2428; MODEL NUMBER: GSM2428 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  This equipment has been tested and found to comply with the limits pursuant to Part 15 Subpart B, Part 22,  and  Part  24  of  the  FCC  rules.  These  limits  are  designed  to  provide  reasonable  protection  against harmful interference in an appropriate installation. This equipment generates, uses, and can radiate radio frequency  energy  and,  if not  used  in  accordance  with  instructions,  can cause  harmful  radiation  to  radio communication. However, there is no guarantee that interference will not occur in a particular installation.  RF EXPOSURE  Your  device  is  a  radio  transmitter  and  receiver.  It  is  designed  and  manufactured  not  to  exceed  the emissions  limits  for  exposure  to  radio  frequency  (RF)  energy  set  by  the  Federal  Communications Commission (FCC) of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted  levels  of  RF  energy  for  the  general  population.  These  guidelines  are  based  on  the  safety standards  previously  set  by  the  U.S.  and  international  standards  bodies.  The  standards  include  a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for wireless RF devices, such as the device, employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. SAR values at or below that limit are considered safe for the general public.  Before a wireless RF device is made available for sale to the Public, it must be tested and certified to the FCC that it does not exceed the SAR limits established by the FCC. Tests for SAR are conducted using the positions and locations (e.g., at the ear or worn on the body) as required by the FCC for each device model. The device has been tested and meets the FCC RF exposure guidelines when used against the body  using the  supplied  belt  clip  under  normal  usage  conditions.  This  device  conforms  with  the  RF  exposure requirements for portable devices in accordance with FCC Part 2.1093. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment for portable devices. Use of non-approved accessories may violate FCC RF exposure guidelines
  - V - Canadian Compliance (Industry Canada)  IC ID: 4160a-GSM2428; MODEL NUMBER: GSM2428 This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.  The GSM2428 has been designed to comply with safety requirements for exposure to radio waves (SAR).  SAR testing has been performed in accordance with RSS-102, with the GSM2428 transmitting at its highest certified power level in all used frequency bands. The highest SAR value for the GSM2428 when tested was 0.477W/Kg.  Please follow the instructions included in the user guide for product installation and use.  Ce  dispositif  est  conforme  à  la  norme  de  l'Industrie  Canada  exempts  de  licence  RSS.  Opération  est assujettie à la suite à deux conditions: (1) ce dispositif ne peut pas causer de brouillage, et (2) ce dispositif doit accepter toutes interférence, y compris le brouillage qui peut causer intempestif de fonctionnement du dispositif.  Le GSM2428 a été conçu pour satisfaire aux exigences de sécurité pour l'exposition aux ondes radio (SAR).  SAR  essais  a  été  réalisée  conformément  aux  flux  RSS-102,  la  transmission  de  GSM2428  à  son  plus  haut niveau de puissance certifiée dans toutes les bandes de fréquences utilisées. La plus haute valeur SAR pour le  GSM2428  lors  de  l'essai  a  été  0.477W  /  Kg.    Veuillez  suivre  les  instructions  incluses  dans  le  guide  de l'utilisateur pour l'installation du produit et l'utilisation.  R&TTE  The device modem has been fully tested and complies with all applicable requirements of EN301489-1, EN301489-3, EN301489-7, EN300440-2, EN60950-1, IEC60950-1 and EN62311. Compliance to EN301 511 has been demonstrated by testing on both the device and the integrated module.   ROHS COMPLIANCE The device complies with the European Union Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment ([RoHS) Directive (2002/95/EC), effective since July 1, 2006.
  - VI - DISCLAIMER The  information  and  instructions  contained  within  this  publication  comply  with  all  FCC,  GCF,  PTCRB, R&TTE, IMEI and other applicable codes that are in effect at the time of publication. Enfora disclaims all responsibility  for  any  act  or  omissions,  or  for  breach  of  law,  code  or  regulation,  including  local  or  state codes,  performed  by  a  third  party.  Enfora  strongly  recommends  that  all  installations,  hookups, transmissions,  etc.,  be  performed  by  persons  who  are  experienced  in  the  fields  of  radio  frequency technologies.  Enfora  acknowledges  that  the  installation,  setup  and  transmission  guidelines  contained within  this  publication  are  guidelines,  and  that  each  installation  may  have  variables  outside  of  the guidelines contained herein. Said variables must be taken into consideration when installing or using the product,  and  Enfora  shall  not  be  responsible  for  installations  or  transmissions  that  fall  outside  of  the parameters set forth in this publication. BATTERY INFORMATION AND SAFETY REQUIREMENTS NOTE: Failure to comply with all of the following precautions could:  Cause personal injury or property damage  Cause abnormal chemical reactions which would make the battery over heat, smoke, distort, leak, or catch on fire  Destroy internal protections built into the battery  Shorten battery life  Reduce battery performance   Precautions  Read this entire manual and the label on the exterior of the battery.  Keep the battery away from sources of excessive heat such as fire, stoves, or direct sunlight.  Keep the battery away from sources of high voltage or static discharge.  Do not use or store the battery with other batteries or where it could touch metal.  Do not put the battery into a microwave oven.  Do not allow the battery to be crushed.  Keep the battery away from children.  Do not drop the battery.  Do not allow anything to touch any of the battery contacts, or to connect two or more of the contacts.  Do not disassemble, destroy, or attempt reassembly of the battery.  Do not place or leave the battery in a damp or wet environment.  Do not allow water to touch the battery.  Do not wrap the battery with conductive material.
  - vii -  Properly dispose of the battery.  Do not incinerate or burn the battery.  Do not leave or discard the battery where it could get wet or become submerged in water.  Do not damage the battery.  Do not weld or solder anything to the battery, the attached wires, or the connector.  Do not use this battery in any device other than supplied.  Do not touch a leaking battery. Avoid leaked-out materials. Do not allow it to touch your skin or clothes. If touched, immediately rinse affected areas thoroughly with water. Leaked materials may cause skin irritation. Seek medical attention if irritation persists. If it contacts your eyes, do not rub your eyes. Rinse the eyes thoroughly with water, and see a doctor immediately.  Use of this battery in other devices could result in unsafe conditions.  Risk of explosion if battery is replaced by an incorrect type. Table of Contents 1  Introduction ........................................................................................................ 2 1.1 Objective ................................................................................................................ 2 1.2 References ............................................................................................................. 2 1.3 Requirements ......................................................................................................... 2 2  Overview ............................................................................................................. 3 2.1 Product Specifications ........................................................................................... 3 2.2 Description ............................................................................................................. 4 2.3 LEDs ........................................................................................................................ 6 2.4 Switches ................................................................................................................. 7 Push To Call (PTC) ..................................................................................................... 7 Set Geo-Fence Button .............................................................................................. 7 User-Defined Button ................................................................................................ 7 Volume Buttons ........................................................................................................ 8 2.5 Interconnections .................................................................................................... 8 USB Connection ........................................................................................................ 8 Headphone Jack ........................................................................................................ 8
  - VIII - Speaker ..................................................................................................................... 9 Two Second Headset Delay ................................................................................... 9 Microphone .............................................................................................................. 9 SIM ............................................................................................................................ 9 Battery ...................................................................................................................... 9 3  Installation ........................................................................................................ 10 3.1 Opening ................................................................................................................ 10 3.2 Battery Installation .............................................................................................. 11 3.3 Removing the Battery .......................................................................................... 12 3.4 Inserting the Battery ............................................................................................ 13 3.5 Charging the Battery ............................................................................................ 13 Mini MT Battery Charging Guidelines .................................................................... 14 3.6 SIM Card Insertion ............................................................................................... 14 3.7 USB Driver Installation (Windows XP) ................................................................. 16 3.8 USB Driver Installation (64 Bit Windows 7) ......................................................... 23 4  Configuration .................................................................................................... 31 4.1 Configuration ....................................................................................................... 31 4.2 Dispatch Number ................................................................................................. 31 4.3 SMS Destination ................................................................................................... 31 4.4 Set GeoFence ....................................................................................................... 32 User Definable Buttons .......................................................................................... 32 4.5 Setting the Emergency Call Number .................................................................... 32 4.6 Dialing the Emergency Call Number .................................................................... 33 4.7 Configuring the PC ............................................................................................... 33 Default Serial Parameters ....................................................................................... 33
  - IX - Determine which COM port to use ........................................................................ 33 Start HyperTerminal ............................................................................................... 35 4.8 Demo Configuration to the Enfora Test Server ................................................... 38 Reset the modem to factory defaults .................................................................... 38 Connecting the Mini MT to the Enfora Test Server ............................................... 38 Configure the Modem to Access the GPRS network. ............................................. 39 Verify Registration Status ....................................................................................... 40 Verify GPRS Activation ............................................................................................ 40 Configure the modem to access the Enfora Server. .............................................. 41 Verifying Server connectivity.................................................................................. 42 5  GPS Operation and Verification ......................................................................... 43 5.1 GPS Operation and Verification ........................................................................... 43 5.2 Verification of GPS Lock ....................................................................................... 43 5.3 Verify GPS Operation ........................................................................................... 43 GPS Operation from Enfora Demo Server .............................................................. 43 6  Software Features ............................................................................................. 44 Additional Software Features ................................................................................. 44
  1  Introduction 1.1 Objective This document provides a brief introduction to the Enfora® Mini MT personal asset tracking device. This guide will provide basic instructions for configuring a Mini MT for evaluation purposes. Advanced features are described in detail in the following reference documents: 1.2 References  GSM2428AT001 - Enfora Mini MT AT Commands  GSM2428CB001 - Enfora Mini MT Cook Book  GSM2428TG001 - Enfora Mini MT Transition Guide 1.3 Requirements Getting started with the Enfora Mini MT will require the following:  Mini MT (GSM2428)  USB to mini-USB cable (sold separately) (CAW-6000-0006)  Activated SIM card (not supplied)  Personal Computer (not supplied)  Operating Systems: Windows XP or Windows 7 64 Bit  USB port  The USB Driver Setup Utility for the Mini MT is available on the Enfora website at www.enfora.com.
  2  Overview 2.1 Product Specifications   Characteristics   Dimensions (L x W x H) 102 x 60.5 x 25.4 mm Housing Polycarbonate Weight <120 g     Radio Performance   Frequency 850/900/1800/1900 MHz Transmit Power Class 4 (2W@850/900 MHz)  Class 1 (1W@1800/1900 MHz)     Packet Data   Mode Class B, Multislot 8 Protocol GPRS Release 97 Coding Schemes CS1-CS4 Packet Channel PBCCH/PCCCH     GSM Functionality   Voice AMR, EFR, FR & HR CS Data Asynchronous; Transparent and Non-Transparent up to 14.4 kb/sec GSM SMS PDU, MO/MT, Cell Broadcast     Over-The-Air Commands GPS TX internal, binary reporting, timed reporting, maximum speed exceeded, status change reports, GPS content, event reporting, distance reporting, geofencing, FOTA     Interface   Host Protocols AT Commands, UDP API, PPP Internal Protocols PPP, UDP API, TCP API API Control/Status AT Commands, UDP API, TCP API, AT Commands Over SMS
  SIM Interface I/O   SIM Internal 1.8/3.0 V SIM accessed via battery compartment Interface Mini USB jack for power and local data access Audio 2.5 mm headset Power AC adapter and optional vehicle power adapter     Environment   Operating –20ºC to 55ºC (Due to Battery Limitations with Lithium Ion) Storage –20ºC to 60ºC Humidity Up to 95% non-condensing     Power   Battery Rechargeable Lithium-Ion 1400 mAh     Certifications   FCC Parts 2, 15, 22 & 24 GCF Version 3.39.1 PTCRB Version 5.6.0 Industry Canada Yes CE Mark Yes RoHS Compliant Yes   Specifications subject to change. 2.2 Description The Mini MT is a small, ruggedized certified quad-band device optimized for personal asset tracking. The device has 5 buttons, 4 LEDs, a microphone, speaker, and headphone jack. The device is intended to be used in either a body worn environment or remotely installed on equipement. The device ships with a belt clip, see figure 5, when the device is used as a personal tracker the belt clip is the only supported method of carrying the device on the body. It is required that the belt clip side of the device is facing the body, use on the body in other orientations is not supported.
   Figure: 1  - Mini MT Overview      Figure: 2  - Mini MT Front View (Showing LEDs)
   Figure: 3  - Mini MT Side View (Showing Push to Call Button)    Figure: 4  - Mini MT Side View (Showing USB Port)   2.3 LEDs There are four LEDs used to provide status to the user. The LED functions are defined in the table below.   CALL  (Yellow) ON  (Yellow) GPS  (Yellow) BAT  (Red) Hibernate OFF OFF OFF If the battery charge level is <20%, the BAT LED blinks slowly, i.e. every 10 seconds. OFF if the battery charge level is less than 5% Active / Blinks on for 500ms, off for 1s, when receiving or Slow Blink on for 500 ms, off Blinks on for 500ms, off for 2s, when locked. If the battery charge level is <20%, the BAT LED blinks
  Battery originating call. Blinks on for 2s, off for 2s for missed call. ON solid during call. for 10s slowly i.e. every 10 seconds. OFF if the battery charge level is less than 5%   Active / Aux Blinks on for 500ms, off for 1s, when receiving or originating call. Blinks on for 2s, off for 2s, for missed call. ON solid during call ON solid Blinks on for 500ms, off for 1s, when receiving or originating call. Blinks on for 2s, off for 2s, for missed call. ON solid during call Blinks on for 500ms, off for 2s during charge.   NOTE: The LEDs will blink when upgrading the firmware on the Mini MT.     2.4 Switches Push To Call (PTC) The Push To Call (PTC) switch allows the user to place a call to a number that has been programmed. Set Geo-Fence Button The Mini MT "ʘ" button is programmable through the event engine. The default state is to configure a ½ mile radius geo-fence at the current location. This radius may be re-defined and is retained in non-volatile memory. User-Defined Button The User-Defined button "<" is programmable. Some examples of these functions include: generate a call to a number different from the PTC button, generate a geo-fence with different parameters than the geo-fence button, send an SMS of the current location to a cell phone, send the current location to the server, etc.
  Volume Buttons The Mini MT has two volume buttons for controlling the audio volume level. These buttons are functional whether in a call or not. The ‘+’ button is used for increasing volume and the ‘–’ button is used for decreasing volume.   NOTE: While you are on an active phone call, the volume buttons will function in both headset and hands-free mode.   2.5 Interconnections USB Connection The USB connector (see Figure 4) is used for charging the battery and for data communication. The unit will charge from a laptop computer, AC to USB power adapter, or vehicle power to USB adapter.  Data communications with the Mini MT is also performed through the USB connector. The USB connection is used to configure or customize the Mini MT operation. This connection is also used to provide GPS NMEA data to a mapping or user application.   NOTE: The device should only be connected to a USB 1.0, 1.1 or 2.0 port. The USB to Mini-USB cable used must be either USB 1.1 or USB 2.0 compliant. The USB cable and vehicle power to USB adapter are both sold separately.   Headphone Jack The headphone jack provides the user with the ability to connect a standard 2.5mm headset (sold separately) when the speakerphone mode is not desirable.
  Speaker An integrated speaker allows the user to make a phone call to the pre-configured dispatch number when in hands-free mode. The user can adjust the volume to a comfortable level using the volume up (‘+’) or down (‘-’) buttons.   The voice operation of the Mini MT is intended for use in Speakerphone or headset modes only. It is not designed for operation against the head and has not been approved for use in this manner.   Two Second Headset Delay When switching between Headset and Speaker, there is a delay of approximately two seconds. Microphone A built-in sensitive microphone allows the user to communicate comfortably at up to 3 feet away for hands-free operation. SIM A SIM card holder is located under the battery on the bottom of the Mini MT. The SIM card is required to enable the voice and data communication capabilities of the Mini MT device. Battery A 1400 mAh Li-Ion battery is supplied with the Mini MT. The Mini MT battery life varies based on configuration and use of the Mini MT. The battery must be installed in the Mini MT in order to configure or use the device.
  - 10 - 3  Installation 3.1 Opening The Mini MT may have a belt clip attached. To open the Mini MT the belt clip must first be removed. The following steps provide instructions for how to remove the belt clip and open the Mini MT.   Lift the retainer clasp on the belt clip and slide the belt clip off the Mini MT  Figure: 5  - Removal of Mini MT belt clip
  - 11 - Figure: 6  - Removal of Mini MT belt clip       The battery door clasp can be rigid and resistant to opening, If this is the case, do not use a screw-driver to open as this could cause damage to the device.  If the battery door clasp is too stiff a coin could be used to apply leverage.  Figure: 7  - Opening the Mini MT battery door.   3.2 Battery Installation The Mini MT is supplied with a 1400 mAh Lithium-Ion rechargeable battery with built-in safety features. The battery should be removed to gain access to the SIM card and for turning the unit off (shipping or travel). The battery is shipped with a red protective cover over the battery terminals and must be removed before use. The following steps provide instructions for how to remove or replace a battery.
  NOTE: The Mini MT cannot be used without a battery. Running the Mini MT only on USB power without a battery is not supported.   3.3 Removing the Battery Access to the battery is through the battery door on the bottom of the Mini MT. Pull up on the battery using the thumb latch until the battery releases from the retention clips. Slide the battery away from the contacts and remove from the Mini MT.    Figure: 8  - Mini MT Battery Cover     NOTE: The battery is initially provided with a red protective cover over the terminals. Remove the protective cover by peeling off of the battery to expose the terminals. Discard the protective cover after removal.
  3.4 Inserting the Battery While the battery cover is removed, insert the battery into the battery compartment with the contacts aligned with the Mini MT power contacts. The battery must be inserted into the battery compartment at a 45-degree angle with the contact end first. Ensure the contacts of the battery line up with the contacts in the Mini MT. Push the battery in towards the contacts and then down firmly until fully seated in the battery compartment. Replace the battery access door ensuring the latch is locked firmly in place. 3.5 Charging the Battery The Mini MT must be fully charged prior to initial use. Charging your Mini MT battery may be done using a standard USB Mini cable (optional: CAW-6000-0006) connected to your desktop personal computer (PC).   NOTE: The PC must be turned on or powered up while charging the Mini MT.   For charging the Mini MT battery in a vehicle, an optional USB to vehicle accessory power adapter is available (PSA-9000-0002) for purchase.   NOTE: Many vehicles do not provide power to the accessory jack when the vehicle ignition is off.   An alternate method for charging using AC power may be performed with the AC power to USB power adapter (PSA-9000- 0101). Which is available for purchase. Connect one end of the USB cable to the Mini MT and the other end to your power source. The Mini MT ON LED will be on solid and the BAT LED will flash while charging. When the Mini MT is fully charged the BAT LED will be off and the ON LED will be on solid while connected to a USB power source. NOTE: The USB cable needs to be either USB 1.1 or USB 2.0 compliant.
  Note: The AC power adapter used to charge the unit must be capable of supplying 5V@500mAh.   Mini MT Battery Charging Guidelines The battery supplier specifies that the charging temperature range is between 0°C and 45°C. Charging outside the recommended range may cause excessive heat or serious damage to the battery.   Do not use or leave the Mini MT in the hot sun or inside a car in direct sunlight for extended periods. This may cause the battery to generate heat, swell, smoke, or flame. It might also cause deterioration of the battery cell’s capacity or longevity.   A fully depleted battery typically takes 5 hours to charge. The actual charging time will depend on multiple factors, including:  The level of charge remaining in the battery  The amount of current available from the USB host.  The ambient temperature The temperature cut off for charging is 45°C on the high end, 0°C on the low end. The battery will not charge while outside this range. Once the battery reaches 100% charge, the charging current to the battery will be cut off until such time as the battery may need additional charge. The USB will power the unit so long as the battery is in place. The charging LED blinks red while charging and turns off when the charging has stopped. The LED will also blink if the battery level is low (i.e. 20%) and the unit is not plugged in to a charger.   3.6 SIM Card Insertion The SIM, an integral part of any GSM terminal device, is a “smart card” that is programmed with subscriber information. The user information consists of an International Mobile Subscriber Identity (IMSI) number which is registered with the GSM/GPRS service provider and an encryption Ki (pronounced “key”). This information consists of a microprocessor and memory installed on a plastic card. A SIM card can be
  installed by simply inserting the SIM card in the SIM slot provided inside of the device. The SIM slot is located under the battery and the battery door. To install the SIM card into the Mini MT device, follow these steps: 1. Remove the battery cover from the underside of the Mini MT by pushing the tab toward the front of the unit. 2. Remove the battery. 3. You will see the SIM card holder in the Mini MT. 4. Slide the SIM card holder to the unlocked position (as shown in the following figure) and the door will lift up.    5. Slide the SIM card into SIM door. Make sure the notch on the SIM is aligned with the notch in the SIM holder. 6. Close the SIM door. 7. Slide the SIM lock to the left. The SIM card holder MUST be locked. 8. Place the battery back in the Mini MT, making sure the connectors are aligned properly. 9. Replace the battery cover.   Note: The SIM card is not provided with the Mini MT device. The SIM must be obtained from the GSM/GPRS service provider and must be provisioned by the operator for data and/or voice. Always take care to protect the SIM. Mini MT’s GSM/GPRS related functionality will not operate without the SIM installed.   Enfora is not liable for damages to the Mini MT when inserting a SIM card inside the device.
      3.7 USB Driver Installation (Windows XP) These instructions illustrate how to correctly install the USB drivers in Windows XP using the Enfora Driver Setup Utility.  1. Run the Enfora Driver Setup Utility by double clicking the EnforaDriverSetup executable file.  The Enfora Driver Setup Utility Extraction window will open.  Figure: 9  - Enfora Driver Setup Utility Extraction Once the contents have been extracted to memory the Welcome Window is displayed.
   Figure: 10  - Enfora Driver Setup Utility Welcome 2. To install the drivers, select the Install button. The Enfora Driver Setup Utility Prepare System Window will be displayed.
   Figure: 11  - Enfora Driver Setup Utility Prepare System Window 3. Select the Next button to continue. The Enfora Driver Setup Utility Installation Window will be displayed while the system installs the drivers. Be sure to disconnect any Enfora devices. Previous drivers will be removed during this phase.
   Figure: 12  - Enfora Driver Setup Utility Installation Window
   Figure: 13  - Enfora Driver Setup Utility Driver Installation  4. When prompted to install the device driver select the Next button.
   Figure: 14  - Enfora Driver Setup Utility Driver Installation Progress 5. During the driver install phase you may be prompted to Continue or Stop installation due to potential compatibility issues. Select the Continue Anyway button.
  Figure: 15  - Windows Security Window Upon completion of the installation the Enfora Driver Setup Utility Driver Install Completion Window is displayed.      Figure: 16  - Enfora Driver Setup Utility Driver Install Completion Window 6. Select the Finish button. When the installation is complete the list of Attached Devices will be displayed within the Enfora Driver Setup Utility Attached Devices Window
   Figure: 17  - Enfora Driver Setup Utility Attached Devices Window   3.8 USB Driver Installation (64 Bit Windows 7) These instructions illustrate how to correctly install the USB drivers in Windows 7 using the Enfora Driver Setup Utility.  1. Run the Enfora Driver Setup Utility by double clicking the EnforaDriverSetup executable file.  The Enfora Driver Setup Utility Extraction window will open.
   Figure: 18  - Enfora Driver Setup Utility Welcome Window Once the contents have been extracted to memory the Welcome Window is displayed.
   Figure: 19  - Enfora Driver Setup Utility Preparation Window 2. To install the drivers, select the Install button. The Enfora Driver Setup Utility Prepare System Window will be displayed.
   Figure: 20  - Enfora Driver Setup Utility Installation Window 3. Select the Next button to continue. The Enfora Driver Setup Utility Installation Window will be displayed while the system installs the drivers. Be sure to disconnect any Enfora devices. Previous drivers will be removed during this phase.
   Figure: 21  - Enfora Driver Setup Utility Driver Installation  4. When prompted to install the device driver select the Next button.  Figure: 22  - Windows Security Window During the driver install phase you may be prompted to Continue or Stop installation due to potential compatibility issues. Select the Install this driver software anyway button.
   Figure: 23  - Enfora Driver Setup Utility Driver Install Completion Window Upon completion of the installation the Enfora Driver Setup Utility Driver Install Completion Window is displayed. 5. If the Status displayes an issue click on the Correct issues button 6. At the "OK to apply fix" prompt, click on the Yes button.
   Figure: 24  - Enfora Driver Setup Utility Attached Devices Window  Figure: 25  - Enfora Driver Setup Utility Apply Fix Window When the installation is complete the list of Attached Devices will be displayed within the Enfora Driver Setup Utility Attached Devices Window.
   Figure: 26  - Enfora Driver Setup Utility Attached Devices Window
  4  Configuration 4.1 Configuration The Mini MT must be configured before use. Configuration is performed through AT commands from a PC computer. A terminal program is required to interface to the Mini MT through the USB cable. The drivers for the Mini MT support Windows XP and Windows 7 64 Bit operating systems. While Enfora uses HyperTerminal to configure the Mini MT, the user can use another terminal program. The Mini MT drivers must be installed on your computer before proceeding.  4.2 Dispatch Number The “Dispatch Number” is the phone number the Mini MT will call when the Push-To-Call (PTC) button is pressed. To configure the Mini MT to call phone number “1-214-555-1212” enter the following command: AT$DSPATCH=“12145551212” <Enter> After entering the dispatch number enter: AT&W <Enter> to save. This will ensure that if the battery is removed the number will not need to be re-entered. 4.3 SMS Destination The SMS Destination Address is where the Mini MT would send an SMS text message. The Mini MT can store up to five (5) SMS Destination Addresses. The following example shows how to set an SMS Destination Address: AT$SMSDA=1, “19875551212”<Enter>
  4.4 Set GeoFence There are two user-definable buttons on the Mini MT. The first button is factory-defined to set a geo-fence. Depressing the Geo-Fence button will place a half-mile radius circular geo-fence around the Mini MT. When the Mini MT exits the geo-fence an alert message will be sent via SMS message to the SMS Destination Address defined in the AT$SMSDA field. (Messages and alerts can also be sent via GPRS packet data. The user has the ability to control the IP and port that the packet data is transmitted to) The factory default configuration of the Mini MT will not have any SMS Destination Addresses configured and will not be capable of generating SMS messages for Geo-Fence events.   User Definable Buttons The Mini MT "ʘ" button is user-definable through the event engine. The default state is to configure a ½ mile radius geo-fence at the current location. The Mini MT "<" button is user-definable through the event engine. This button function is not defined from the factory. 4.5 Setting the Emergency Call Number The Mini MT is capable of dialing an emergency number (AT$EMERNUM) and a dispatch number (AT$DSPATCH). The default emergency number in the Mini MT is “411.” The provider should reconfigure this number to the correct emergency number for the region the Mini MT will operate in. To set the emergency number to “911” enter the following text in the terminal window: AT$EMERNUM=“911” <enter> AT&W <enter> The first command sets the emergency number to 911 and the second command saves the setting.
  4.6 Dialing the Emergency Call Number Depending on the Mobile Operators network configuration, the Mini MT will allow emergency communications without a SIM card installed. Follow these steps to initiate an emergency call:   1. Depress the user-defined button. 2. Hold the user-defined button (<). 3. Press and hold the PTC button. 4. The ON, GPS, and BAT LED’s will flash in unison. 5. Momentarily release the user-defined button (<) while still holding the PTC button. 6. Press the user-defined button (<) again. 7. The CALL LED will flash. 8. Release the user-defined (<) and the PTC buttons.   The Mini MT will establish a call to the emergency number configured in the AT$EMERNUM command. 4.7 Configuring the PC NOTE: The following examples use Windows XP and HyperTerminal. Any Terminal program should work, using the parameters shown below. Default Serial Parameters  Baud Rate: 115200 baud rate  Data Bits: 8  Stop Bits: 1  Parity: None  Flow Control: None   Determine which COM port to use On older computers, there is usually a built in COM port. This is normally COM1
  With a USB connection, you will need to determine which COM port it is using. 1. Open up the System Properties window. This is done through the Control Panel > System or right-click on My Computer and select Properties. Select the Hardware Tab. On Windows XP the screen looks like the following:  2. Select the Device Manager button. Expand the Ports section by selecting the ‘+’ sign beside “Ports (COM & LPT).
  3. Your window should look similar to the following: 4. Plug the Mini MT into your USB port. The window should change to show Mini MT USB to UART Device. 5. Most devices will show the COM port next to the device name. Record this number.   NOTE: Make sure there is no “!” or “X” next to the USB device. If you see an “!” or an “X,” the device is not properly installed and will not work.   Start HyperTerminal The following configuration steps assume that you are using the Windows XP Operating System. Follow these steps: 1. Click Start>Programs>Accessories>Communications>HyperTerminal 2. You should see the following screen.
     3. Enter a name for the connection. In this example, the name is Enfora MiniMT. 4. Click OK. 5. The next window that will appear is the Connect To window.  6. Change the Connect Using setting to the COM port that was determined in Section 7.3.2, Step 2. For the example we are using COM3. 7. Click OK. 8. The next window is the Port Settings window.
     9. Set the communication port to 115200 bits per second, 8 data bits, no parity, 1 stop bit and no flow control. 10. Make sure the settings match the example. 11. Click OK. 12. The Main Program Window should appear.  13. Type the command ATI in the main window and press the Enter key.
  14. You should see the following screen with the response from the Mini MT: 15. The response “Enfora, Inc.” indicates that you are successfully communicating with the Enfora Mini MT. 4.8 Demo Configuration to the Enfora Test Server The Mini MT is capable of communicating with a server. The following steps will guide you through a configuration that will demonstrate the data communication capabilities to the Enfora Test Server. A valid SIM card from your carrier is required that allows GPRS data communications capability. Reset the modem to factory defaults To restore the Mini MT to factory defaults send the following command: AT&F<CR> To save the current configuration to memory send the following command: AT&W<CR> Reset the modem with the following command: AT$RESET<CR> Connecting the Mini MT to the Enfora Test Server The following information will be required from the SIM card provider (refer to GSM0000AN019 – Network Configuration Worksheet):  APN  Username (if required)  Password (if required)  SIM PIN (if required) The following examples show how to configure the Mini MT with a Cingular SIM card with the following data:  APN=isp.cingular  Username=ISP@CINGULARGPRS.COM  Password=CINGULAR1  SIM PIN=1234
  Configure the Modem to Access the GPRS network. De-register the Mini MT from the network using the following command: AT+CFUN=0 <CR> Set the modem with the proper APN (Access Point Name) using the following command: AT+CGDCONT=1,”IP”,”APN”<CR>   NOTE: Replace the letters “APN” with the APN that was provided to you by your wireless carrier   Example: AT+CGDCONT=1, “IP”, “isp.cingular” Set the username and password with the following command: AT%CGPCO=1, “<username>,<password>”,0<CR>   NOTE: Substitute the correct username and password, if your cellular carrier requires a username and password.   Example: AT%CGPCO=1, “ISP@CINGULARGPRS.COM,CINGULAR1”,0<CR> Configure the Mini MT for auto GPRS registration with the following command: AT$AREG=2<CR> Save the changes to memory with the following command: AT&W<CR> The Mini MT should be reset to ensure the changes are used. Reset the Mini MT with the following command: AT$RESET<CR>
  Verify Registration Status Verify GSM status by sending the following command: AT+CREG?<CR> If everything is working, you should receive one of two responses: +CREG: 0,1 (GSM registered to home network) OR +CREG: 0,5 (GSM registered roaming.) Verify GPRS status by sending the following command: AT%CGREG?<CR> If everything is working, you should receive one of two responses: %CGREG: 0,1 (GPRS registered to home network) OR %CGREG: 0,5 (GPRS registered roaming.) Verify GPRS Activation Enter the following command to verify that the Mini MT is activated on the GPRS network: AT$NETIP?<CR> The Mini MT is activated if it has been assigned an IP address Example of successful GPRS activation: at$netip? $NETIP: "166.217.226.214","066.102.163.231","066.209.010.201"   NOTE: The above IP addresses will be different for each device and location. Non-zero values indicate a successful GPRS activation.   Example of unsuccessful GPRS activation:
  at$netip? $NETIP: "000.000.000.000", "000.000.000.000", "000.000.000.000"   If AT$NETIP returns all zeros, send the following command: AT$CGEER<CR> There are three common responses: $CGEER: no PDP reject cause (Everything should be working properly) $CGEER: requested service option not subscribed (APN is incorrect or SIM has not been enabled for data mode.) $CGEER: user authentication failed (username and/or password is incorrect.) Configure the modem to access the Enfora Server. To configure the modem for server interoperability, several things have to be addressed:  Most GPRS configurations are Mobile Originate only. The mobile modem must initiate a conversation with a remote server before the remote server can talk to the modem.  IP addresses are dynamically assigned and can change.  Some IP addresses are NAT and are non-routable.   These issues are addressed with the following configuration commands. The examples will use the following information:  Modem ID/name = “MMT_Test”  Remote Server IP address = apitest.enfora.com  Remote Server IP port = 1721   Give the modem a unique name with the following command: AT$MDMID=”MMT_Test”
  NOTE: This command, combined with the wakeup message, will allow the server to associate a Public IP address with a specific modem and create a window of opportunity where the server can send commands to the modem.   Configure the modem to talk with a specific server with the following command: AT$FRIEND=1,1,”apitest.enfora.com” Set the port number with the following command: AT$UDPAPI=,1721 Enable periodic messages (wakeup) to be sent to the server every 60 seconds with the following command: AT$WAKEUP=1,1 Configure the Mini MT for auto GPRS registration with the following command: AT$AREG=2<CR> Verifying Server connectivity. For the following tests, Java Runtime must be installed on the computer. (To install Java Runtime, please visit the Java website here: http://www.java.com/en/download/manual.jsp) 1. Start Internet Explorer and enter the following URL: “http://apitest.enfora.com/udpapp/” 2. Enter the name used in the Modem ID (MDMID) command in the box. 3. Select Connect. 4. Select the tab with the modem name (MMT_Test). Within approximately 60 seconds wakeup messages should be seen in the window.   NOTE: Selecting the Clear button will erase the contents of the “(ASCII Data):” window.   5. Enter the following command in the Command / Data text box: ATI 6. Click on the Write button. 7. Verify that you see the following modem response showing Enfora, Inc. If so, you have successfully configured the modem to talk with the server.
  5  GPS Operation and Verification 5.1 GPS Operation and Verification The Mini MT contains an integrated GPS receiver and GPS antenna. For best GPS performance the unit should be placed in an area where it can have direct view of the sky. 5.2 Verification of GPS Lock The Mini MT will provide an indication of successful GPS Lock within approximately 120 seconds when in view of satellites. The GPS LED will flash yellow when it is receiving a sufficient number of satellites to provide status. When this occurs, the internal GPS receiver has enough information to track its current position. 5.3 Verify GPS Operation The Mini MT GPS status may be obtained locally through the USB connection or through the GPRS connection to a server. The following steps allow the user to determine GPS operation through a terminal program and also through the Enfora Demonstration web server. GPS Operation from Enfora Demo Server The same command can be used in the server application by entering AT$GPSRD=10 in the Command / Data text box, then selecting Write. NOTE: The third field is a single character field representing the status of the GPS reading. There are three valid character for this field and are described below:    A = Valid  V = Not Valid  9 = Enfora Specific response that GPS solution is not valid and the last known GPS location is being substituted.
  6  Software Features Additional Software Features The Mini MT supports Firmware Over The Air (FOTA) upgrades. Details about FOTA commands can be found in the AT Command Manual.

Navigation menu