Novatel Wireless RTT2211 CDMA Licensed Transmitter User Manual GSM2374UG001 MT 3000 User Guide
Novatel Wireless Inc. CDMA Licensed Transmitter GSM2374UG001 MT 3000 User Guide
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1884505 |
| Application ID | FCRCkU9IooKDfRwEGrQqYQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | Yes |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 112.48kB (1405969 bits) |
| Date Submitted | 2012-12-24 00:00:00 |
| Date Available | 2013-05-18 00:00:00 |
| Creation Date | 2013-01-22 11:55:28 |
| Producing Software | MadCap Flare V8 |
| Document Lastmod | 2013-01-22 10:13:29 |
| Document Title | GSM2374UG001 - MT 3000 User Guide |
| Document Author: | rkeating |
MT 3050
User Guide
EMT3050UG001
Version:1.00
22 January, 2013
General
TERMS OF USE OF NEW MATERIALS - PLEASE READ CAREFULLY
From time to time, Enfora, in its sole discretion, may make available for download on its website
(www.enfora.com), or may transmit via mail or email, updates or upgrades to, or new releases of, the
firmware, software or documentation for its products (collectively, 'New Materials'). Use of such New
Materials is subject to the terms and conditions set forth below, and may be subject to additional terms
and conditions as set forth in Enfora's Technical Support Policy (posted on its website) and/or any written
agreement between the user and Enfora.
All New Materials are provided AS IS. Enfora makes no warranty or representation with respect to the
merchantability, suitability, functionality, accuracy or completeness of any such New Materials. The user of
such New Materials assumes all risk (known or unknown) of such use. Enfora reserves all rights in such
New Materials. The user shall have only a revocable and limited license to use such New Materials in
connection with the products for which they are intended. Distribution or modification of any New
Materials without Enfora's consent is strictly prohibited.
IN NO EVENT WILL ENFORA BE RESPONSIBLE FOR ANY INCIDENTAL, INDIRECT, CONSEQUENTIAL OR
SPECIAL DAMAGES AS A RESULT OF THE USE OF ANY NEW MATERIALS. ENFORA'S MAXIMUM LIABILITY
FOR ANY CLAIM BASED ON THE NEW MATERIALS SHALL NOT EXCEED FIFTY U.S. DOLLARS ($50).
Version Verification
Please ensure you have the latest version of this document by downloading it from www.enfora.com
Copyright
© 2012 Enfora, Inc. All rights reserved. Complying with all applicable copyright laws is the responsibility of
the user. Without limiting the rights under copyright, no part of this document may be reproduced, stored
in or introduced into a retrieval system, or transmitted in any form or by any means (electronic,
mechanical, photocopying, recording or otherwise), or for any purpose, without the express written
permission of Enfora, Inc.
Enfora and the Enfora logo are either registered trademarks or trademarks of Enfora, Inc. in the United
States.
251 Renner Pkwy
Richardson, TX 75080 USA
Phone: (972) 633-4400
Fax: (972) 633-4444
Email: info@enfora.com
www.enfora.com
ii
Warranty Information
[Revised: 11/11/2010]
This warranty applies to (a) products sold directly by Enfora, unless a different warranty is specified in a
written agreement between Enfora and the purchaser; and (b) products sold to end users through a
distributor authorized by Enfora, but only where the authorized distributor does not provide a separate
warranty on such products, and Enfora has agreed to provide this warranty to such end users. If you
purchased the product from an authorized distributor, please check whether this warranty from Enfora, or
a separate warranty from the distributor, applies to your purchase. This warranty does not apply to any (i)
accessories or batteries for the products; or (ii) demonstration samples or prototypes of the products.
Unless otherwise provided in a written agreement between Enfora and the purchaser, all such accessories,
batteries, samples or prototypes are provided by Enfora AS IS without any warranty of any kind.
Enfora warrants to the original purchaser of the product from Enfora or its authorized distributor (as
applicable) that, for a period of one (1) year from the date of shipment of the product from Enfora, the
product hardware will be substantially free from defects in material or workmanship under normal
operation, and the product firmware will perform substantially in accordance with the product
documentation provided by Enfora. Enfora does not warrant that (a) the product hardware or firmware
will meet the purchaser's requirements; (b) the operation of the product hardware or firmware will be
uninterrupted or error-free; or (c) the product, when integrated in, or combined with, other products or
software not supplied by Enfora, will continue to perform substantially in accordance with the product
documentation. This limited warranty is for the benefit of the original purchaser, and is not transferable.
During the warranty period, Enfora, at its expense and in its sole discretion, will repair the product, or
replace the product with a corresponding or equivalent product, if it is determined to have a covered
defect, provided that the purchaser first notifies Enfora (directly or through its authorized distributor from
which the product was purchased) of any such defect, furnishes Enfora with a proof of purchase (if
required), requests and obtains a return merchandize authorization (RMA) number from Enfora, and
returns the product under that RMA to Enfora (or, at Enfora's option, to its authorized distributor), with the
shipping charges being prepaid by purchaser. If, upon reasonable examination of the returned product,
Enfora does not substantiate the defect claimed by purchaser, or determines that the defect is not covered
under this limited warranty, Enfora will not be required to repair or replace the product, but may instead
reship the product to the purchaser (or, at Enfora's option, to its authorized distributor where the product
can be made available to purchaser), in which case the purchaser shall be responsible for paying Enfora's
cost for reshipping the product to purchaser (or to Enfora's authorized distributor), and Enfora's usual
charges for unpacking, testing, and repacking the product for reshipment to purchaser (or to Enfora's
authorized distributor). Purchaser shall bear the risk of loss or damage in transit to any product returned
by purchaser to Enfora, or any returned product not found to be defective or covered under this warranty,
and reshipped by Enfora to purchaser (or to Enfora's authorized distributor). In the event Enfora repairs or
iii
replaces a defective product covered by this limited warranty, the repaired or replacement product will be
covered under this limited warranty for the remainder of the original warranty period on the defective
product, or a period of ninety (90) days, whichever is longer. If Enfora is unable to repair or replace a
defective product covered by this limited warranty, Enfora will provide to purchaser a credit or a refund
(at Enfora's option) of the original purchase price (excluding taxes and shipping charges). Any returned and
replaced product, or any product for which Enfora has furnished a credit or a refund, becomes the
property of Enfora.
Enfora shall not have any obligation to provide any firmware bug fixes, upgrades or new releases except as
may be necessary to correct any covered defect of which purchaser notifies Enfora in writing during the
warranty period. Enfora, from time to time and in its sole discretion, may make available for download on
its website (www.enfora.com), or may provide via email, certain firmware bug fixes, upgrades or new
releases for the product. Download and use of any such bug fixes, upgrades or new releases is subject to all
of the applicable terms and conditions of Enfora's technical support policy as posted and updated on its
website. Enfora shall have no obligation under this limited warranty for (a) normal wear and tear; (b) the
cost of procurement of substitute products; or (c) any defect that is (i) discovered by purchaser during the
warranty period but for which purchaser does not request an RMA number from Enfora, as required
above, until after the end of the warranty period, (ii) caused by any accident, misuse, abuse, improper
installation, handling or testing, or unauthorized repair or modification of the product, (iii) caused by use of
any materials not supplied by Enfora, or by use of the product other than in accordance with its
documentation, or (iv) the result of electrostatic discharge, electrical surge, fire, flood or similar causes.
The purchaser (or its customers, as applicable) shall be solely responsible for the proper configuration,
testing and verification of the Enfora product prior to deployment in the field, and for ensuring that any
end user product or system into which the Enfora product is integrated or incorporated operates as
intended and meets the requirements of purchaser (or its customers). Enfora shall have no responsibility
whatsoever for the integration, configuration, testing, verification, installation, upgrade, support or
maintenance of any such end user product or system, or for any liabilities, damages, costs or expenses
associated therewith.
ENFORA'S SOLE RESPONSIBILITY AND PURCHASER'S SOLE REMEDY UNDER THIS LIMITED WARRANTY
SHALL BE FOR ENFORA TO REPAIR OR REPLACE THE PRODUCT (OR IF REPAIR OR REPLACEMENT IS NOT
POSSIBLE, PROVIDE A CREDIT OR REFUND OF THE PURCHASE PRICE) AS PROVIDED ABOVE. ENFORA
EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF NON- INFRINGEMENT, MERCHANTABILITY,
SATISFACTORY PERFORMANCE AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ENFORA
BE LIABLE FOR ANY INDIRECT, SPECIAL, EXEMPLARY, INCIDENTAL OR CONSEQUENTIAL DAMAGES
(INCLUDING WITHOUT LIMITATION LOSS OR INTERRUPTION OF USE, DATA, REVENUES OR PROFITS)
RESULTING FROM A BREACH OF THIS WARRANTY OR BASED ON ANY OTHER LEGAL THEORY, EVEN IF
ENFORA HAS BEEN ADVISED OF THE POSSIBILITY OR LIKELIHOOD OF SUCH DAMAGES.
iv
Some jurisdictions may require a longer warranty period than specified above and, accordingly, for
products sold in those jurisdictions the applicable warranty period shall be extended as required under the
laws of those jurisdictions. Furthermore, some jurisdictions may not allow the disclaimer of implied
warranties or the exclusion or limitation of incidental or consequential damages, so the above disclaimer,
limitation or exclusion may not apply to products sold in those jurisdictions. This limited warranty gives the
purchaser specific legal rights and the purchaser may have other legal rights that vary from jurisdiction to
jurisdiction. This limited warranty shall be governed by the laws of the State of Texas, United States of
America, without regard to conflict of laws principles. This limited warranty shall not be governed in any
respect by the United Nations Convention on Contracts for the International Sale of Goods.
Regulatory Compliance
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits pursuant to Part 15 Subpart B, Part 22,
and Part 24 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in an appropriate installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not used in accordance with instructions, can cause harmful radiation to radio
communication. However, there is no guarantee that interference will not occur in a particular installation.
RF EXPOSURE
Your device is a radio transmitter and receiver. It is designed and manufactured not to exceed the
emissions limits for exposure to radio frequency (RF) energy set by the Federal Communications
Commission (FCC) of the U.S. Government. These limits are part of comprehensive guidelines and establish
permitted levels of RF energy for the general population. These guidelines are based on the safety
standards previously set by the U.S. and international standards bodies. The standards include a substantial
safety margin designed to assure the safety of all persons, regardless of age and health.
The exposure standard for wireless RF devices, such as the device, employs a unit of measurement known
as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. SAR values at or below
that limit are considered safe for the general public.
The device conforms with the RF exposure requirements for portable devices in accordance with FCC Part
2.1093.
The transmitter is configured with a 10% transmission duty factor, for GPRS Multislot class 2 operation,
and is excluded from routine RF exposure evaluation in accordance with FCC Mobile and Portable Device
RF Exposure Procedures and Equipment Authorization Policies, KDB447498 D01, V04.
The CDMA transmitter is configured with a 1.6% transmission duty factor and is excluded from routine RF
exposure evaluation in accordance with FCC Mobile and Portable Device RF Exposure Procedures and
Equipment Authorization Policies, KDB447498 D01 v05.
R&TTE
Effective with HW revision 1, the device is in conformity with the requirements of the R&TTE directive
1999/5/EC. It has been fully tested and complies with all the requirements of EN301489-1, EN301489-3,
EN301489-7 and EN60950-1. Compliance to EN301511 has been demonstrated by testing on both the
device and the integrated module.
Industry Canada
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
The MT 3050 transmitter is configured with a 10% transmission duty factor, for GPRS Multislot class 2
operation, and is excluded from routine RF exposure evaluation in accordance with the requirements of
RSS-102 section 2.5.
Cet appareil est conforme aux normes d’Industrie Canada exempts de license(s) RSS. Son fonctionnement
est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas provoquer d’interférences, et (2) cet
appareil doit accepter toute interférence, y compris les interférences pouvant provoquer un
fonctionnement indésirable de l’appareil.
L’émetteur MT 3050 est configuré avec un facteur de service de transmission de 10%, pour l’opération en
GPRS multislot class 2, et est exclu de l’évaluation de routine d’exposition RF en conformité avec les
exigences du CNR-102 section 2.5.
vi
ROHS COMPLIANCE
The device complies with the European Union Restriction of the Use of Certain Hazardous Substances in
Electrical and Electronic Equipment ([RoHS) Directive (2002/95/EC), effective since July 1, 2006.
DISCLAIMER
The information and instructions contained within this publication comply with all FCC, GCF, PTCRB,
R&TTE, IMEI and other applicable codes that are in effect at the time of publication. Enfora disclaims all
responsibility for any act or omissions, or for breach of law, code or regulation, including local or state
codes, performed by a third party. Enfora strongly recommends that all installations, hookups,
transmissions, etc., be performed by persons who are experienced in the fields of radio frequency
technologies. Enfora acknowledges that the installation, setup and transmission guidelines contained within
this publication are guidelines, and that each installation may have variables outside of the guidelines
contained herein. Said variables must be taken into consideration when installing or using the product, and
Enfora shall not be responsible for installations or transmissions that fall outside of the parameters set
forth in this publication.
vii
Table of Contents
1 Introduction
1.1 Description
1.2 Technical Specifications
1.3 On-Board Diagnostics Overview
2 Features And Functions
2.1 GPS
2.2 LEDs
2.3 Power
2.4 Accelerometer
2.5 GSM Radio
2.6 CDMA Radio
2.7 New Event Reporting
2.7.1 Vehicle Identification Number (VIN)
2.7.2 Excessive Engine Speed (RPM)
2.7.3 Vehicle Speed
2.7.4 Vehicle Battery Voltage (Low Battery Warning)
2.7.5 Check Engine Light (MIL Alert)
2.7.6 Trip Odometer Reporting
2.7.7 Idle Time Reporting
10
2.7.8 Low Fuel Alert
10
2.7.9 Rapid Acceleration
10
2.7.10 Sudden Deceleration (Harsh Braking)
11
2.7.11 Motion Detection
11
2.7.12 OBDII Basic Event Data
11
2.7.13 Right Turn
11
2.7.14 Left Turn
12
viii
2.7.15 Up
12
2.7.16 Down
12
2.8 Micro USB Connector
13
2.9 Additional Software Features
13
2.9.1 AT Commands Over SMS
13
2.9.2 Store/Transmit Event Data
14
2.9.3 Synchronize RTC Time With GPS Time
14
2.9.4 Reporting Frequency
14
3 Installation
15
3.1 SIM Access (GSM2378 And UMT2212 Only)
15
3.1.1 Opening The Device
15
3.1.2 Inserting The SIM
17
3.1.3 Closing The Device
17
3.2 Activating The Device
18
3.3 Device Installation
18
3.4 Accelerometer Calibration
19
4 USB Driver Installation
21
4.1 USB Driver Installation Using The Enfora Driver Setup Utility (Windows XP)
21
4.2 USB Driver Installation Using The Enfora Driver Setup Utility (Windows 7)
27
5 Network Test Procedure
35
5.1 Configuring The Modem For Test Server Connection
35
5.2 Verifying Server Connectivity
36
6 Accesories
38
6.1 Backup Battery
38
6.2 Plastic Lever
38
ix
1 INTRODUCTION
1.1 Description
The MT 3050 is an integrated device for the Usage Based Insurance (UBI), telematics, and fleet
management markets. It has a rugged plastic housing, and it includes a disconnect alert feature using an
in-device backup battery. It is available in GSM/GPRS, 1xRTT, and HSDPA versions. The MT 3050 contains
an internal GPS, a cellular antenna, a J1962 compliant OBDII connector, a micro USB connector, and 3 LED
indicators.
The GSM2378 and UMT2212 variants also contain an internal SIM card holder.
Figure: 1 - Front Right View
Figure: 2 - Front View
The MT 3050 has a printed label on the top side of the device. The figure below shows the information
included on the label.
Figure: 3 - MT 3050 Labels
1.2 Technical Specifications
Housing
OBD Protocols
Dimensions: (L x W x H) 55 x 49 x 29 mm
Rugged textured plastic enclosure UL94-Vo fire
rated
Some vehicles only support a subset of these protocols, which may
limit the functionality of the MT 3050.
Environment
Operating: Battery version: -20ºC to +60ºC
Storage: Battery version: -20ºC to +60ºC
Humidity: Up to 85% non-condensing
Vibration: In accordance with SAE J1211
SIM Card / Interface / I/O
Radio Technology
GSM/GPRS: 850/900/1800/1900 MHz
1xRTT (CDMA2000) : 800/1900 MHz
HSDPA (UMTS 3G): 850/1900 MHz or
900/1900/2100
[GSM/GPRS/Edge 2G: 850/900/1800/1900 MHz]
GPS Protocols: NMEA, Binary
Buffered GPS Message Feature: Yes
Motion Detection
3-axis digital accelerometer for motion alerts, towing alerts, and driver behavior reporting (rapid
acceleration, harsh braking) using configurable
thresholds
Packet Data
Packet data characteristics include:
SMS Functionality includes:
Host Protocols: AT commands, UDP API, FOTA
Internal Protocols: UDP API, TCP API
API Control/Status: AT commands, UDP API, TCP
API, AT commands over SMS
Battery
Class B, Multislot 8
GSM/GPRS Rel 97
J1850 PWM, J1850 VPW, ISO-9141-2, ISO-14230
KWP2000, and ISO-15765 CAN protocols supported, VIN, excessive engine speed (RPM),
vehicle speed,vehicle battery voltage (low battery
warning), check engine light (MIL alert), odometer
(trip distance), idle time reporting, low fuel alert
Interface
SIM Access: Internal
Cellular Antenna: Internal
GPS Antenna: Internal
LEDs: GPS (blue), Cellular (green), OBD (red)
I/O Connector: Micro USB (2.0), command port
OBDII Connector: J1962 compliant
On-Board Diagnostics (OBDII)
GPS Functionality
ISO 15765 (CAN)
ISO 9141-2
ISO 14230 KWP 2000
J1850 PWM
J1850 VPW
GSM/HSDPA SMS: Text, PDU, MO/MT,
Cell Broadcast
CDMA SMS: Text, MO/MT
Rechargeable lithium-ion battery (230mAh)
Battery recharging range is 0 to +45ºC (Internal
battery temperature)
Power
Operating Voltage: 9 - 16 V DC operational for 12
V vehicle support per SAE J1455
Part Numbers
Certifications
GSM2378-00 (GSM/GPRS)
RTT2211-00 (CDMA 1xRTT)
UMT2212-00 (HSDPA + GPRS/Edge)
CAB2374-01 (J1962 extension cable)
Additional Features
FCC: Yes
CE: Yes
RoHS Compliant: Yes
Industry Canada:Yes
Document References
GSM Registration
GPRS Registration
Velocity
Geo-Fence
IP Status
GPS Status
Timer
MT Power Save
RTC Alarm
Memory Full Percentage
Input Event Counter
GPS Overspeed
Message Log Count
SMS Indication
GPS Distance
Spider MT 3050 AT Command Set For GPRS
(EMT3050AT001)
Spider MT 3050 AT Command Set For 1xCDMA
(EMT3050AT002)
Spider MT 3050 AT Command Set For HSDPA
(EMT3050AT003)
GSM Network Configuration Worksheet
(GSM0000AN019)
Applicable Products
The MT 3050 series has three models:
GSM2378-00 (GSM/GPRS)
RTT2211-00 (CDMA 1xRTT)
UMT2212-00 (HSDPA + GPRS/Edge)
This user guide identifies the features that are specific to each
model.
1.3 On-Board Diagnostics Overview
An On-Board Diagnostics (OBD) system controls engine functions and serves as the diagnostic control
network of the vehicle. All cars built and sold in the United States since 1996 must be equipped with the
newer OBDII system. The Enfora MT 3050 connects to a vehicle's OBDII port and monitors the OBDII
system using a variety of communication protocols.
The MT 3050 can be configured to provide notification messages based on events triggered by:
Accelerometer change
Check engine light (MIL alert)
Engine RPM
GPS information
Idle time
Low fuel
Trip Odometer (trip distance)
Vehicle battery voltage (low battery warning)
Vehicle Identification Number (VIN)
Vehicle speed
Other events monitored by the OBDII system
Some vehicles are not compatible with the MT 3050. If the vehicle is not compatible
with the parameters the MT 3050 requires, then functionality may be limited,
problematic, or unavailable.
The SAE (Society of Automobile Engineers) 1979 standard defines the method for requesting diagnostics
data and provides a list of standard parameters from the engine control unit.
Compliance to this standard is the responsibility of the vehicle manufacturer, therefore Enfora cannot
guarantee performance of the MT 3050 with every vehicle.
2 FEATURES AND FUNCTIONS
2.1 GPS
GPS functionality includes:
NMEA update with all data points
Enfora Binary Packets
Buffered GPS message feature
Geo-fencing
Virtual odometer
2.2 LEDs
The MT 3050 includes LEDs to indicate OBDII, NETWORK, and GPS status.
The following figures show the MT 3050 connectors and LEDs.
Figure: 4 - MT 3050 Connectors
Figure: 5 - MT 3050 LEDs
The following table describes the LED operation.
MT 3050 LEDs
OBD
(Red)
The OBD LED will flash at a fast rate when the unit is first connected to the OBD port for power. Once a protocol is
discovered through the OBD port, the LED will flash at a slow rate.
NETWORK
(Green)
The NETWORK LED will flash at a fast rate when the unit is finding cellular coverage. Once cellular coverage is found, the
LED shall flash at a slow rate.
GPS
(Blue)
The GPS LED will flash at a fast rate when the unit is acquiring a satellite fix. Once a fix is acquired, the LED will flash at
a slow rate.
Table: 6 - MT 3050 LEDs
2.3 Power
The MT 3050 requires 9-16 VDC minimum 2 amps input power. Pin 16 on the 16-Pin IO connector is the
positive power input, and pin 4 and 5 is the ground. This device contains a battery. This battery is not to be
removed or replaced by the user. Please dispose of this device according to local recycling laws.
2.4 Accelerometer
The three-axis digital accelerometer provides the following features:
Motion alert (towing alert)
Driver behavior reporting
l Rapid acceleration
l Harsh braking
Configurable thresholds
l Range settings
l Mode (Normal, Sleep, Wakeup)
l Wakeup pause (20 to 2560 msec)
l Sample Rate (0-25 per second)
l Filter Coefficient and Filter Bandwidth
l Device Orientation Setup
2.5 GSM Radio
The MT 3050 (GSM2378) contains a quad-band (850/900/1800/1900 MHz) GSM radio.
Class 4 (2W@850/900 MHz)
Class 1 (1W@1800/1900 MHz)
2.6 CDMA Radio
The MT 3050 (RTT2211) contains a dual-band (800/1900 MHz) CDMA radio.
BC0-800 MHz – US Cell
BC1-1900 MHz – US PCS
2.7 New Event Reporting
The MT 3050 has additional event reporting not supported by other Enfora products. For general event
reporting information and for detailed information about these new events refer to the MT 3050 AT
Command Document (GSM2374AT001).
2.7.1 Vehicle Identification Number (VIN)
The VIN is used as a unique identifier which is sent at first power up with heartbeat messages and with
events.
Vehicle manufacturers are responsible for defining the list of data returned,
therefore not all vehicles support retuning the Vehicle Identification Number.
2.7.2 Excessive Engine Speed (RPM)
Excessive engine speed alerts are triggered when the engine speed (in RPM) exceeds a defined RPM level
(in ¼ RPM increments) for a defined period of time in seconds (e.g., 30 seconds).
The MT 3050 has three definable thresholds.
Unnecessary wear and tear on the powertrain control module (PCM) may occur if constant or frequent
excessive engine speed is reported. The excessive engine speed event may be caused by one of the
following situations:
Obstructions, such as ice or mud, that may cause wheel slippage if the obstruction is not removed
from the vehicle
Revving the RPM while in neutral
Speeding or reckless driving that causes excessive RPM engine speed
The following AT command example sets the excessive engine speed threshold at 1 to 4000 RPM. Then, if
exceeded for 3 seconds, it triggers the input event. This event will clear once engine RPM is below 4000 for
30 seconds.
AT$OBDEES=1,4000,3,30
2.7.3 Vehicle Speed
If configured for vehicle speed alerts and the vehicle moves faster than one of the three configurable
thresholds (e.g., 70 MPH), then a vehicle speed alert is triggered.
The following AT Command example sets the vehicle speed threshold at 1 to 112 KPH (~70MPH). When the
threshold is exceeded for 10 seconds, an input event is triggered. This event will clear when the vehicle
speed is reduced to 104KPH (~65MPH).
AT$OBDSPD=1,112,10,104
2.7.4 Vehicle Battery Voltage (Low Battery Warning)
The vehicle battery voltage alert is triggered when the vehicle’s battery is reported to be below a threshold
(e.g., 10.8 V) for a user-defined period of time in seconds (e.g., 300 seconds).
The following AT Command example sets the low battery threshold to 10.8 volts. When the voltage
remains below this threshold for 300 seconds (5 minutes), it triggers an input event. Restoring voltage
above the threshold for 300 seconds (5 minutes) will clear this event.
AT$OBDLBL=10800,300,300
2.7.5 Check Engine Light (MIL Alert)
When the vehicle's “Check Engine” light illuminates, this indicates that a vehicle issue requires attention
for diagnosis and/or repair. This is also known as a Malfunction Indicator Light (MIL). A user can configure
a device to detect a MIL issue through the OBDII protocol, and to send an alert when the device detects
such an issue.
2.7.6 Trip Odometer Reporting
Trip odometer reporting provides the odometer miles accumulated from ignition-on to ignition-off, which
is considered a “trip”.
Ignition events are not yet detected on hybrid or electric vehicles.
2.7.7 Idle Time Reporting
An idle time event is triggered when the vehicle’s engine is running without the vehicle moving (i.e.,
velocity less than 3 KPH) for a defined period of time in seconds (e.g., 300 seconds).
The alert is cleared when the vehicle speed exceeds another speed and time threshold.
Both the violation and clearing of the alert are reported if configured.
The following AT Command example sets the idle time speed threshold to 3 KPH for 5 minutes (300
seconds) with a clearance time of 30 seconds. If the speed remains below this threshold for 300 seconds (5
minutes), it triggers the input event. Restoring speed above this threshold for 30 seconds will clear this
event.
AT$OBDIDL=3,300,30
2.7.8 Low Fuel Alert
The low fuel alert triggers when the vehicle’s fuel level falls below a defined threshold in percent (e.g.,
12%) for a defined period of time in seconds (e.g., 60 seconds).
The following AT Command example sets the low fuel alert threshold to 12% for 1 minute (60 seconds)
with a clearance time of 30 seconds. If the fuel level remains below this threshold for 60 seconds, it
triggers the input event. Restoring the fuel level above this threshold for 30 seconds will clear this event.
AT$OBDLFL=12,60,30
2.7.9 Rapid Acceleration
Rapid acceleration events can be triggered when one of three available thresholds are exceeded as
determined by the accelerometer in milli-Gs (e.g., 0.75) for a defined period of time in seconds (e.g., 30
seconds).
The following AT Command example sets the rapid acceleration threshold #1 to .2G. If this threshold is
exceeded for 1 second, then an input event is triggered. Keeping the acceleration of the vehicle below this
threshold for 30 seconds will clear this event.
AT$OBDACL=1,200,1,30
10
2.7.10 Sudden Deceleration (Harsh Braking)
Rapid deceleration events can be triggered when one of three available deceleration thresholds are
exceeded as determined by the accelerometer in milli-Gs (e.g., 1.0) for a defined period of time in seconds
(30 seconds).
The following AT Command example sets the rapid deceleration threshold #1 to .5Gs. If this threshold is
exceeded for 1 second, then an input event is triggered. Keeping the deceleration below this threshold for
30 seconds will clear this event.
AT$OBDDCL=1,500,1,3
2.7.11 Motion Detection
Motion alerts for vehicles can be configured to communicate that a vehicle is being towed. Motion
detection based on measuring movement via the accelerometer occurs when the vehicle ignition is off,
and the vehicle is stationary.
A motion alert is triggered when motion defined in milli-Gs is detected for a defined period of time.
2.7.12 OBDII Basic Event Data
Five additional data items can be included with event messages:
VIN
Firmware version ($PKG)
OBD Protocol (i.e., J1850 PWM)
Cellular signal strength (RSSI)
OBD speed
2.7.13 Right Turn
Harsh turn events can be triggered when one of two available thresholds are exceeded as determined by
the accelerometer in milli-Gs (e.g., 0.75) for a defined period of time in seconds (e.g. 30 seconds).
The following AT command example sets the Right Turn accelerometer threshold 1 to .25 Gs. If this
threshold is exceeded for 2 seconds, trigger the input event. This event will clear in 15 seconds when the
acceleration is below this threshold.
AT$OBDART=1,250,2,15
11
2.7.14 Left Turn
Harsh turn events can be triggered when one of two available thresholds are exceeded as determined by
the accelerometer in milli-Gs (e.g., 0.75) for a defined period of time in seconds (e.g., 30 seconds).
The following AT command example sets the Left Turn accelerometer threshold 2 to .3Gs. If this threshold
is exceeded for 1 second, trigger the input event. This event will clear in 20 seconds when the acceleration
is below this threshold.
AT$OBDALT=2,300,1,20
2.7.15 Up
Up accelerometer events can be triggered when the threshold is exceeded as determined by the
accelerometer in milli-Gs (e.g., 0.75) for a defined period of time in seconds (e.g., 30 seconds).
The following AT command example sets the Up accelerometer threshold to 1.2Gs. If this threshold is
exceeded for 1 second, trigger the input event. This event will clear in 30 seconds when the acceleration is
below this threshold.
AT$OBDAUP=1,1200,1,30
2.7.16 Down
Down accelerometer events can be triggered when the threshold is exceeded as determined by the
accelerometer in milli-Gs (e.g., 0.75) for a defined period of time in seconds (e.g., 30 seconds).
The following AT command example sets the Down accelerometer threshold to .8Gs. If this threshold is
exceeded for 1 second, trigger the input event. This event will clear in 30 seconds when the acceleration is
below this threshold.
AT$OBDADN=1,800,1,30
12
2.8 Micro USB Connector
The MT 3050 includes a J1962 compliant OBDII connector and a micro USB I/O port.
The Micro USB (2.0) connector is an input/output connector and is not intended for
general use. This connector should only be used when programming the modem.
This USB port cannot be used to supply power to other USB devices and nothing
should be connected to this port when the vehicle is in motion. The MT 3050 can not
be powered through the USB Port.
The micro USB connector is only used to program the modem. When programming the modem, a micro
USB cable is required which you must purchase separately.
Figure: 7 - Micro USB Cable
2.9 Additional Software Features
2.9.1 AT Commands Over SMS
A user can send AT commands to the MT 3050 via SMS. Please refer to Enfora Application Note
ENF0000AN012 - AT Commands Over SMS for details..
13
2.9.2 Store/Transmit Event Data
The user can configure the MT 3050 to store event-generated data in its internal memory to be sent over
the air to a remote server. This feature can be enabled or disabled using the AT$MSGLOGEN command.
“Total Number of Unread Messages” is decremented if an unread message is read via the AT$MSGLOGRD
command.
Example: Assume there are 50 unread messages in the message queue, and the total number of messages
in the message queue is 100. This means that the first 50 messages have been read while the last 50
messages have not been read. If a user sends AT$GPSLOGRD=0,1,51 then the total number of unread
messages drops down to 49 after successful transmission of that message. However, if a user sends
AT$GPSLOGRD=0,1,99 then the total number of unread messages still remains at 50—that message is
transmitted to the remote server.
A user can also read a message stored in the memory by inputting the appropriate starting index number.
2.9.3 Synchronize RTC Time With GPS Time
The Real Time Clock ("RTC") is synchronized with GPS time automatically every time the device is powered
up and first acquires valid GPS data. Additionally, the RTC time is synched with GPS time every time the
GPS time rolls over from 23:59:59 to 00:00:01.
2.9.4 Reporting Frequency
The minimum reporting frequency of the device is as follows:
Periodic reporting is limited to max of 1 per 6 seconds.
The general reporting interval is 1 message every 2 seconds.
14
3 INSTALLATION
3.1 SIM Access (GSM2378 And UMT2212 Only)
SIM Installation procedures include:
Opening
Inserting SIM
Closing
The GSM2378 and UMT2212 versions of the MT 3050 include an onboard SIM carrier. There is no external
access to the SIM.
The RTT221 (CDMA) version of the MT 3050 does not use a SIM and should not be
opened.
3.1.1 Opening The Device
To prevent damaging the device, we highly recommend that you use the Plastic Lever (Enfora part number
ASA-3000-0001) when opening the MT 3050.
To open the MT 3050, follow these steps:
1. Insert the tool into the opening and gently push until that corner of the lid unsnaps as shown below.
15
Figure: 8 - Opening the MT 3050 Case
2. Repeat step 1 for the other corner.
Figure: 9 - MT 3050 With Cover Unsnapped
3. Carefully slide the cover off the device.
Figure: 10 - MT 3050 With Cover Partially Removed
Figure: 11 - MT 3050 With Cover Removed
16
3.1.2 Inserting The SIM
Insert the SIM using the following procedure:
The SIM card is not provided with the MT 3050 device. The SIM must be obtained
from the GSM/GPRS service provider and must be provisioned by the operator for
data. Always take care to protect the SIM. Without the SIM installed, the MT 3050
modem is not able to communicate on the network.
1. Using the correct tool, carefully remove the device cover to access the internal SIM holder as previously described.
2. Insert the SIM into the SIM holder of the MT 3050.
3. Replace the cover as described in the next section.
3.1.3 Closing The Device
Replace the MT 3050 cover by using the following steps:
A. Place the MT 3050 cover onto the base as shown in the following figure.
1. Apply gentle downward pressure to the back of the cover first as you carefully slide the cover
into place.
2. Apply gentle down and forward pressure to the front of the cover until it snaps shut.
17
Figure: 12 - MT 3050 Cover Replacement
3.2 Activating The Device
With CDMA devices, the user must contact the service provider to activate the device. They will need to
provide the MEID of the device to the provider. Once the provider has acknowledged that the device is
ready to activate, the user will then be required to send an activation string to the network.
Send the activation string: AT+CDV*22899. This will initiate a call with the network. A successful call will
last approximately 40 seconds. If the call is terminated within 10-15 seconds, the call was not successful.
Several attempts might be required. If after, a few attempts the call is not successful, please check the
MEID of the device and compare it to the MEID provided to the provider.
To verify that the activation has successfully completed, attempt a voice call AT+CDVxxxxxx. If the call is
successful, then the OTASP (Over-the-Air Service Provisioning) was successful.
3.3 Device Installation
Make sure the vehicle is parked on level ground prior to installing the MT 3050.
Instructions provided in this section describe the hardware installation of the MT 3050 device. To install
the MT 3050 in a vehicle, follow these steps:
1. Locate the OBDII socket. The location will vary between different vehicle manufacturers, models,
and production years.
2. Carefully insert the MT 3050 into the OBDII socket.
3. After the device is installed, ensure the device is working properly as evidenced by a GPS lock and cellular connection, which can be validated by the LEDs.
The MT 3050 is NOT a waterproof or sealed device. Care must be taken to ensure the
device is kept away from water or any other liquids.
18
Figure: 13 - Typical OBDII Socket Location
The device starts the accelerometer auto-calibration process immediately after the
device is installed and the vehicle's ignition is turned on.
3.4 Accelerometer Calibration
The accelerometer undergoes an automatic calibration sequence on the first drive after any of the
following events:
Device installation
Software upgrade
Vehicle battery replacement (or recharge if battery was fully discharged)
Device auxiliary processor reset
19
Failure to follow the process below could cause an undesired behavior of the motion
feature. Failure to drive straight on level ground during the automatic calibration
may reduce the accuracy of the accelerometer and have an adverse impact on
events triggered by accelerometer readings.
1. Make sure the vehicle is parked on level ground prior to installing the MT 3050.
2. Drive the vehicle in a straight path on level ground during the automatic calibration. An inclined surface will put part of the gravity vector into the XY plane, which will affect the acceleration thresholds. (A 5.7 degree angle will place 10 % of the gravity vector into the XY plane.)
When the vehicle passes 32 KPH, the auxiliary processor assumes that the vehicle is
moving in a straight line and determines the forward axis.
20
4 USB DRIVER INSTALLATION
4.1 USB Driver Installation Using The Enfora Driver Setup
Utility (Windows XP)
These instructions illustrate how to correctly install the USB drivers in Windows XP using the Enfora Driver
Setup Utility.
1. Run the Enfora Driver Setup Utility by double-clicking the EnforaDriverSetup executable file.
The Enfora Driver Setup Utility Extraction window opens.
Figure: 14 - Enfora Driver Setup Utility Extraction
21
Once the contents have been extracted to memory, the Welcome Window opens.
Figure: 15 - Enfora Driver Setup Utility Welcome
2. To install the drivers, select Install.
The Enfora Driver Setup Utility Window opens.
22
Figure: 16 - Enfora Driver Setup Utility Prepare System Window
3. Select Next to continue.
The Enfora Driver Setup Utility Installation Window opens while the system installs the drivers.
4. Disconnect any Enfora devices.
Previous drivers will be removed during this phase.
During the installation, your computer's display may freeze and appear nonresponsive. If this occurs, allow the computer to continue working. After 2-3 minutes,
the display and installer will resume normal behavior.
23
Figure: 17 - Enfora Driver Setup Utility Installation Window
Figure: 18 - Enfora Driver Setup Utility Driver Installation
5. When prompted to install the device driver, select Next.
24
Figure: 19 - Enfora Driver Setup Utility Driver Installation Progress
You may see the following warning message:
Figure: 20 - Windows Security Window
25
6. Click Continue Anyway.
When installation of the USB drivers is complete, the Completion window opens.
Figure: 21 - Enfora Driver Setup Utility Driver Install Completion Window
7. Click Finish.
When the installation is complete, the list of attached devices will appear within the Attached
Devices Window.
26
Figure: 22 - Enfora Driver Setup Utility Attached Devices Window
4.2 USB Driver Installation Using The Enfora Driver Setup
Utility (Windows 7)
These instructions illustrate how to correctly install the USB drivers in Windows 7 using the Enfora Driver
Setup Utility.
1. Run the Enfora Driver Setup Utility by double-clicking the EnforaDriverSetup executable file.
The Enfora Driver Setup Utility Welcome window opens.
27
Figure: 23 - Enfora Driver Setup Utility Welcome Window
Once the contents have been extracted to memory, the Driver Setup Window opens.
28
Figure: 24 - Enfora Driver Setup Utility Preparation Window
2. To install the drivers, click Install.
The Enfora Driver Setup Utility Prepare System Window opens.
29
Figure: 25 - Enfora Driver Setup Utility Installation Window
3. Select Next to continue.
The Enfora Driver Setup Utility Installation Window opens while the system installs the drivers.
4. Disconnect any Enfora devices.
Previous drivers will be removed during this phase.
During the installation, your computer's display may freeze and appear nonresponsive. If this occurs, allow the computer to continue working. After 2-3 minutes,
the display and installer will resume normal behavior.
30
Figure: 26 - Enfora Driver Setup Utility Driver Installation
5. When prompted to install the device driver, select Next.
Figure: 27 - Windows Security Window
6. Select Install this driver software anyway.
31
During the driver install phase, you may be prompted to continue or stop installation due to potential
compatibility issues.
Figure: 28 - Enfora Driver Setup Utility Driver Install Completion Window
When installation of the USB drivers is complete, the Completion window opens.
7. If there are no errors, click Finish.
8. If the status displays an issue, click Correct issues!
9. At the "OK to apply fix" prompt, click Yes.
32
Figure: 29 - Enfora Driver Setup Utility Attached Devices Window
Figure: 30 - Enfora Driver Setup Utility Apply Fix Window
When the installation is complete, the list of Attached Devices appears within the Enfora
Driver Setup Utility Attached Devices window.
33
Figure: 31 - Enfora Driver Setup Utility Attached Devices Window
34
5 NETWORK TEST PROCEDURE
Use the following instructions to configure the Enfora modem to communicate with the Enfora test server.
5.1 Configuring The Modem For Test Server Connection
To configure the modem for server interoperability, consider the following:
Most configurations are Mobile Originate only.
Mobile modem initiates a conversation with a remote server before it can talk to the modem.
IP addresses are dynamically assigned and can change.
Some IP addresses are NAT and are non-routable.
These issues are addressed in the following configuration commands.
Modem ID/name = “My_MT_TEST”
Remote Server address = http://apitest.enfora.com/UDPAPP/
Remote Server IP port = 1721
Give the modem a unique name with the following command:
AT$MDMID="My_MT_TEST"
This command, combined with the wakeup message will allow the server to associate
a Public IP address with a specific modem, and can create an opportunity where the
server can send commands to the modem.
Configure the modem to talk with a specific server with the following command:
AT$FRIEND=1,1,”apitest.enfora.com”
Set the port number with the following command:
AT$UDPAPI=,1721
Set up the server to send out periodic wakeup messages every 60 seconds with the following command:
35
AT$WAKEUP=1,1
5.2 Verifying Server Connectivity
For the following tests, ensure that you have Java Runtime installed on your computer. To install Java
Runtime, please visit the Java website here: http://www.java.com/en/download/manual.jsp
1. Start a web browser and enter the following URL:
http://apitest.enfora.com/UDPAPP/
Figure: 32 - apitest.enfora.com/UDPAPP/ Window
2. Enter the name used in the Modem ID (MDMID) command in the box.
3. Select Connect.
36
4. Select the tab with the modem name (My_MT_Test). Within approximately 60 seconds you should
see a wakeup message in the window.
Selecting the Clear button will erase the contents from the (ASCII Data) window.
5. Enter the following command in the Command/Data text box:
ATI
6. Click on the Submit button.
7. Verify that you see the modem response: Enfora, Inc.
If so, you have successfully configured the modem to talk with the server.
37
6 ACCESORIES
The following accessories are available for the MT 3050:
Part Name
Part Number
Plastic Lever
ASA-3000-0001
Backup Battery
TBD
6.1 Backup Battery
The backup battery's primary function in the MT 3050 is to provide the ability for a user to be notified
when the device is removed from the vehicle.
Input Event 63 can be used to trigger an output event that can be configured in the same manner as the
other output events. If the modem is off (power savings), it will be turned on. If GPS data is configured in
the output event, and the data is not available, the last known position can be configured to be used in the
output message.
AT$OBDBBT is used to configure the time (in seconds) that the device will stay powered after removal
from the vehicle. The range is 30-6000 with the default being 600. In addition, to prevent damage to the
battery, the device will turn itself off when the battery reaches the level determined to be the lowest
“safe” value.
If the configured output message has not been sent when the timer or battery level dictates the device to
shut down (and is configured to do so), it will be saved and sent the next time the device registers on the
network.
6.2 Plastic Lever
Use the Plastic Lever to open the device. For more information on opening the device, see the SIM Access
section in this User Guide.
Figure: 33 - Plastic Lever
38
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Encryption : Standard V1.2 (40-bit) User Access : Print, Fill forms, Extract, Assemble, Print high-res Author : rkeating Create Date : 2013:01:22 11:55:28-06:00 Modify Date : 2013:01:22 10:13:29-08:00 Subject : Language : en-us XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Format : application/pdf Creator : rkeating Description : Title : GSM2374UG001 - MT 3000 User Guide Metadata Date : 2013:01:22 10:13:29-08:00 Keywords : Producer : MadCap Flare V8 Document ID : uuid:90f94b73-b0c6-4b30-8715-c54a419775ae Instance ID : uuid:f87476ce-5ea1-4b5d-a13b-cd19f6e39e4c Page Mode : UseOutlines Page Count : 48EXIF Metadata provided by EXIF.tools