Nutek ATEA Car Alarm User Manual 510 TX GUIDE revA

Nutek Corporation Car Alarm 510 TX GUIDE revA

Users Manual

128-69871 of 51213345BUTTON RECEIVERCHANNEL SYSTEM FUNCTIONLock and Arm Alarm, also initiates andterminates *PanicUnlock and Disarm, also initiates andterminates *Panic. Programmable tounlock drivers door and or all doors.Lock and arm/unlock and disarm. Maybe programmed to unlock driver's dooror all doors. Also will initiate andterminate *Panic.Pulsed output to OUTPUT CHANNEL 2/ TRUNK RELEASE.When pressed and release two times,will provide pulsed output to OUTPUTCHANNEL 3When so equipped, this button can beused to operate an optional deviceconnected to OUTPUT CHANNEL 4.When so equipped, this button can beused to operate an optional deviceconnected to OUTPUT CHANNEL 5.These transmitters make use of icons (symbols) to identify the reactionyour security system/keyless entry/and or remote start system, whereapplicable, will have when any icon (button) is pressed. Theseiconsare programmed at time of installation to meet the needs of theindividual and to complement the vehicle that the system is installed in.To replace a transmitter or add transmitters, please follow theprogramming instructions listed on the pages of this manual.Transmitter Programming GuideModel5WTXB* Where So Equipped128-69872 of 52Some of the more popular options available for the unused OptionButtons of your transmitter are:AS 9554 Remote Garage Door InterfaceAS 9075 Remote Car Starter ModuleAS 9153 Remote Window Roll Up ModuleAS 9256 Remote Trunk Release RelayAlthough the most common use of the transmitter buttons are shownon the front page of this guide, any button or button combination can beprogrammed into any receiver channel. Additionally, if all 4 buttons areused and you require access to a 5th channel, you would program acombination of buttons to control the 5th function. i.e... You haveprogrammed lock for arm, unlock for disarm, trunk for trunk release,and Opt1 for garage door operation, and you've added a window upmodule that you want independentcontrol of, you would program un-lock and trunk buttons pressed simultaneously into the receiver to con-trol this function independently. Also, if you do not program a transmit-ter button into channel 2 which is the separate unlock/disarm chan-nel, then whatever button is programmed into channel 1 will serveas both lock/arm & unlock/disarm.PROGRAMMING TRANSMITTERS:NOTE: It is important to remember that during the programming mode,each individual step must be completed within 15 seconds ofthe previous step. If the 15 second time limit expires betweensteps,the unit will automatically exit the program mode. Thisis indicated by a long chirp from the siren.Non alarm models will flash the parking lights only to confirm thetransmitter code has been learned and stored.NOTE: Because the system may be capable of sounding a siren, thevehicle horn, or both, where the siren chirp is referenced be-low, the siren may chirp, the horn may beep, or both devicesmay sound.TO PROGRAM ADDITIONAL TRANSMITTERS:1)Enter the vehicle, and turn the ignition switch to the ON position.2)Press and release the valet push button switch three times.3)The dash mounted LED will flash 1x, and the siren will chirp 1x,indicating that the system is ready to accept programming of channel#1 which is arm/lock, disarm/unlock/unlock 2, and panic functions.4)Press and hold the lock or lock/unlock symbol button of the transmit-ter you wish to program for 4 seconds or until a long chirp is heardfrom the siren. Repeat step 4 for each transmitter you wish toprogram.NOTE: If your transmitter button has the Lock/Unlock icon on onebutton, press and release the valet push button switch 2 timesthen move on to step #8.
128-69873 of 535)Press and release the valet push button switch one time to advanceto channel 2. The siren will chirp 2 times and the dash mounted LEDwill flash 2 times, indicating that the unit is ready to accept program-ming for channel # 2 which is only used for separate lock andunlock button transmitters, and is the disarm/unlock/unlock 2 andpanic.6)Press and hold the unlock symbol button of the transmitter you wishto program for 4 seconds or until a long chirp is heard from thesiren.Repeat step 6 for each transmitter you wish to program.7)Press and release the valet push button switch one time to ad-vance to channel 3. The siren will chirp 3 times and the dashmounted LED will flash 3 times, indicating that the unit is readyto accept programming for channel # 3 which is the trunk re-lease/alternate output channel of the system.8)Press and hold the trunk/key symbol button of the transmitter youwish to program for 4 seconds or until a long chirp is heard from thesiren.Repeat step 8 for each transmitter you wish to program.9)Press and release the valet push button switch one time to advanceto channel 4 if so equipped. The siren will chirp 4 times and thedashmounted LED will flash 4 times, indicating that the unit is readyto accept programming for channel # 4, optional device (whereequipped)10)Press and hold the Option button of the transmitter you wish toprogram for 4 seconds or until a long chirp is heard from the siren. Repeat step 10 for each transmitter you wish to program.11)Press and release the valet push button switch one time to ad-vance to channel 5 if so equipped. The siren will chirp 5 times andthe dash mounted LED will flash 5 times, indicating that the unit isready to accept programming for channel # 5 optional device (whereequipped)12)Press and hold the second Option button of the transmitter youwish to program for 4 seconds or until a long chirp is heard from thesiren. Repeat step 12 for each transmitter you wish to program.ERASING TRANSMITTERS IF THEY HAVE BEEN LOST OR STOLEN:NOTE: Before you begin to erase the lost or stolen transmitter(s),have all transmitters available that you wish to remain pro-grammed. These will be used during the program processto identify transmitters that will continue to be used.Enter the transmitter program mode:1.Turn the ignition switch to the ON! position.2.Within 10 seconds, press and release the valet/program switchthreetimes. (Siren emits 1 short chirp indicating channel 1 hasbeen entered)128-69874 of 543.Within 10 Seconds, press and hold the ARM or ARM/DISARMbutton of the first transmitter you wish to remain stored into thecontrol unit until a single chirp is heard from the siren.(Repeat this for each transmitter you wish to remain stored in the controlunit).The receiver stores up to four transmitters. To be certain all transmitterslots in the receiver are occupied with transmitters you wish to con-tinue to use, and all others are erased, you will have to fill all fourreceiver slots. If in step 3 you identified one transmitter, you will haveto fill the additional 3 slots. If in step 3 you identified two transmitters,you will have to fill the additional two slots, etc...4.Press and hold any unused button or combination of buttons until along chirp is heard from the siren. Release and press the button orbutton combination again and again until all remaining slots are full.NOTE: The button or combination of buttons entered will also controlthe arm or arm/disarm function until additional transmitters areadded. All unwanted transmitters are now deleted.REPRIORITIZING A TRANSMITTER S PROGRAMMING:To reprogram a receiver channel with a different transmitter buttononce a code has been stored, there will be two options:1. Enter the transmitter program mode of the receiver channel to bereprogrammed. Using any unused button or combination of but-tons, push out the stored code by pressing the unused button untila long chirp is heard, then repeat 3 additional times. After this, youcan add any desired unused transmitter button. This action erasesonly the button stored of the transmitter you are programming. Allother codes will remain stored.2. Enter the transmitter program mode. Using any transmitter buttonpress and hold until a long chirp is heard. If a single chirp or multiplechirps, (up to 7 chirps), are heard, the unit is indicating that thetransmitter has already been programmed elsewhere in the re-ceiver. Release the transmitter button and within 5 seconds pressand hold until a long chirp is heard. This action forces the unit toerase all stored codes of that transmitter.The unit then exits the program mode the siren emits the program modeexit chirp pattern. All transmitter buttons for that transmitter must nowbe reprogrammed. Any other transmitter stored in the unit"s memory stillremain operational. If the button is released and not pressed againwithin the 5 second period, no change in programming has been madeto the receiver channel. The programmer can move onto a differentchannel or erase the transmitter codes as described in 1 above.OPERATING THE FLASHLIGHT OF 5WTX-BIf the transmitter packaged with your system included the5WTX-B, (Flashlight Transmitter) By pressing the button located on thebuttom of the transmitter will cause the light on the end of the unit to turn
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions. 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. Per FCC 15.21, you are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 128-6987 5 of 5

Navigation menu