Nutek ATGA TRANSMITTER User Manual 1286516

Nutek Corporation TRANSMITTER 1286516

Users manual

112133*4*5BUTTON RECEIVERCHANNEL SYSTEM FUNCTIONLock And Arm Alarm, also initiate andterminates *PanicUnlock And Disarm, also initiates andterminates *Panic. Programmable tounlock drivers door and or all doors.Lock and arm/unlock and disarm. Maybe programmed to unlock driver's dooror all doors. Also will initiate andterminate *Panic.Pulsed or switched output to controlRemote Trunk Release or optionaldevice connected to channel 3.When pressed and release two times,will provide pulsed output or activate theRemote Start option when installed.When so equipped, this button can beused to operate an optional deviceconnected to channel 4.When so equipped, this button can beused to operate an optional deviceconnected to channel 5.These transmitters makes use of icons (symbols) to identify the reac-tion your security system/keyless entry/and or remote start system,where applicable, will have when any icon (button) is pressed.These icons are programmed at time of installation to meet the needs ofthe individual and to complement the vehicle that the system is installedin. To replace a transmitter or add transmitters, please follow theprogramming instructions listed on the pages of this manual.Transmitter Programming Guide* Where So Equipped
2Some of the more popular options available for the unused OptionButtons of your transmitter are:AS 9075 Remote car starterAS 9153 Remote window roll upAS 9256 Remote trunk release relayAlthough the most common use of the transmitter buttons are shownon the front page of this guide, any button or button combination can beprogrammed into any receiver channel. Additionally, if all 4 buttons areused and you require access to a 5th channel, you would program acombination of buttons to control the 5th function. i.e... you haveprogrammed lock for arm, unlock for disarm, trunk for trunk release,and OPT1 for garage door operation, and you've added a window upmodule that you want independent control of, you would program un-lock and trunk buttons pressed simultaneously into the receiver to con-trol this function independently. Also, if you do not program a transmit-ter button into channel 2 which is the separate unlock/disarm chan-nel, then whatever button is programmed into channel 1 will serveas both lock/arm & unlock/disarm.PROGRAMMING TRANSMITTERS:NOTE: It is important to remember that during the programming mode,each individual step must be completed within 15 seconds ofthe previous step. If the 15 second time limit expires betweensteps, the unit will automatically exit the program mode. Thisis indicated by a long chirp from the siren.Non alarm models will flash the parking lights only to confirm thetransmitter code has been learned and stored.NOTE: Because the system may be capable of sounding a siren, thevehicle horn, or both, where the siren chirp is referenced be-low, the siren may chirp, the horn may beep, or both devicesmay sound.Note: Some systems are capable of single button programming, if youralarm module is capable of this feature, simply complete step 4of these programming instructions for each transmitter you wishto control your system and exit the program mode by switchingoff the ignition key.TO PROGRAM ADDITIONAL TRANSMITTERS:1) Enter the vehicle, and turn the ignition switch to the on position.2) Press and release the valet push button switch three times.Note: Some systems may use a combination push-button LEDswitch. In these systems the push-button and the dash mountedLED are one and the same.3) The dash mounted LED will flash 1x, and the siren will chirp 1x,indicating that the system is ready to accept programming of channel#1 which is arm/lock, disarm/unlock/unlock 2, and panic functions.
34) Press and hold the lock or lock/unlock symbol button of the transmitteryou wish to program for 4 seconds or until a long chirp is heard fromthe siren."Repeat step 4 for each transmitter you wish to program".NOTE: If your transmitter button has the Lock/Unlock icon onone button, press and release the valet push button switch 2 timesthen move on to step #8.5) Press and release the valet push button switch one time to advance tochannel 2. The siren will chirp 2 times and the dash mounted LED willFlash 2 times, indicating that the unit is ready to accept programmingfor channel # 2 which is only used for separate lock and unlockbutton transmitters, and is the disarm/unlock/unlock 2 and panic.6) Press and hold the unlock symbol button of the transmitter you wishto program for 4 seconds or until a long chirp is heard from the siren."Repeat step 6 for each transmitter you wish to program".7) Press and release the valet push button switch one time to advanceto channel 3. The siren will chirp 3 times and the dash mounted LEDwill Flash 3 times, indicating that the unit is ready to acceptprogramming for channel # 3 which is the trunk release/alternateoutput channel of the system.8) Press and hold the trunk/key symbol button of the transmitter you wishto program for 4 seconds or until a long chirp is heard from the siren."Repeat step 8 for each transmitter you wish to program".9) Press and release the valet push button switch one time to advanceto channel 4 if so equipped. The siren will chirp 4 times and the dashmounted LED will Flash 4 times, indicating that the unit is ready toaccept programming for channel # 4, optional device (where equipped)10) Press and hold the Option button of the transmitter you wish toprogram for 4 seconds or until a long chirp is heard from the siren."Repeat step 10 for each transmitter you wish to program".11) Press and release the valet push button switch one time to ad-vance to channel 5 if so equipped. The siren will chirp 5 times and thedash mounted LED will Flash 5 times, indicating that the unit is readyto accept programming for channel # 5 optional device (whereequipped)12) Press and hold the second Option button of the transmitteryou wish to program for 4 seconds or until a long chirp is heard fromthe siren."Repeat step 12 for each transmitter you wish to program".13) Within 10 seconds, press and release the valet programswitch one time.(Siren emits 6 short chirps indicating channel 6 has been entered)14. Within 10 Seconds, Press and hold the unlock button, (or anyunused button(s)), of the first transmitter you wish to controlChannel 6 output, (Driver Priority 1) until a long chirp is heard fromthe siren.
4(Repeat this for each transmitter you wish to operate the Channel6 output, Driver Priority 1)15. Within 10 seconds, press and release the valet program switchone time.(Siren emits 7 short chirps indicating channel 7 has been entered)16 .Within 10 Seconds, Press and hold the unlock button (or anyunused button(s)) of the first transmitter you wish to controlChannel 7 output, (Driver Priority 2) until a long chirp is heard fromthe siren.(Repeat this for each transmitter you wish to operate the Channel7 output, Driver Priority 2)NOTE: Channels 6 and 7 can be used as a separate output tocontrol a function other than driver priority. Simply program-ming any unused transmitter button other than the unlockbutton will allow complete independent control of theseoutputs.ERASING TRANSMITTERS IF THEY HAVE BEEN LOST OR STOLEN:NOTE: Before you begin to erase the lost or stolen transmitter(s), haveall transmitters available that you wish to remain programmed. Thesewill be used during the program process to identify transmittersthat will continue to be used.Enter the transmitter program mode:1. Turn the ignition switch to the “ON” position.2. Within 10 seconds, press and release the valet/program switch threetimes. (Siren emits 1 short chirp indicating channel 1 has beenentered)3. Within 10 Seconds, press and hold the ARM or ARM/DISARMbutton of the first transmitter you wish to remain stored into thecontrol unit until a single chirp is heard from the siren.(Repeat this for each transmitter you wish to remain stored in thecontrol unit).The receiver stores up to four transmitters. To be certain all transmitterslots in the receiver are occupied with transmitters you wish to con-tinue to use, and all others are erased, you will have to fill all fourreceiver slots. If in step 3 you identified one transmitter, you will haveto fill the additional 3 slots. If in step 3 you identified two transmitters,you will have to fill the additional two slots, etc...4. Press and hold any unused button or combination of buttons until along chirp is heard from the siren. Release and press the button orbutton combination again and again until all remaining slots are full.NOTE: The button or combination of buttons entered will also controlthe arm or arm/disarm function until additional transmitters areadded. All unwanted transmitters are now deleted.
910805 5Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu