Nutek ATHA TRANSMITTER User Manual AX901 owners revA

Nutek Corporation TRANSMITTER AX901 owners revA

User manual

Using Your Remote Control Arming the Security SystemTo arm the system, exit the vehicle, close all doors, then press the LOCK button on the remote control. The systemwill sound 2 times and the parking lights will flash 2 times, indicating the system is armed, has locked the doors (ifequipped and connected) and activated the starter disable feature. The status indicator (blue warning light on thedash) will blink steadily, once per second. To arm the system silently, press and hold the LOCK button for 1 second.The parking lights will flash 2 times, indicating the system is armed, has locked the doors (if equipped andconnected) and activated the starter disable feature. The status indicator (blue warning light on the dash) will blinksteadily, once per second. Pre-arm ModeIf the system sounds 1 time and the parking lights flash only 1 time, this indicates that the vehicle’s interior light ison or an entrance is left open. Check to see that all doors hood and trunk are closed properly. Once all entrancesare secured (and the interior light is off), this system will sound/flash again. The system is now fully armed. (If theentrance is not secured within 4 minutes, the system will arm and ignore the unsecured entrance until it is closed.) Disarming the Security SystemTo disarm the system press the UNLOCK button. The system will sound and the parking lights will flash once, andthe doors will unlock (if equipped and connected). To disarm the system silently, press and hold the UNLOCKbutton for 1 second. The parking lights will flash, indicating the system is disarmed and has unlocked the doors (ifequipped and connected). Disabling/Enabling Confirmation Chirps1. Turn the ignition key ON then OFF.2. Within 10 seconds push and release the valet/override button 3 times.3. The system will sound 2 times to disable confirmation chirps or 1 time to enable confirmation chirps. Attempted Intrusion IdentificationThis system will inform you if an intrusion attempt has occurred while you were away from the vehicle. If an intrusionattempt occurred, the system will sound 4 times and the parking lights will flash 3 times when disarming the system.Enter the vehicle an observe the dash mounted status LED to Identify which zone was triggered.1. Shock Sensor - 1 flash, pause 1 flash, etc.2. Hood or Trunk Pin switch - 2 flashes, pause 2 flashes, etc.3. Door Entry - 3 flashes, pause 3 flashes, etc.The intrusion warning indicators are stored in the system’s memory and will be erased when the ignition key isturned on. Two Stage Door Unlock (Optional)If this feature is enabled on your system, pressing the UNLOCK button one time on the remote control will unlockonly the driver’s door. Press UNLOCK again to unlock the remaining doors. Activating the Trunk Release Feature (Optional)If this feature is enabled on your system, pressing and holding the TRUNK button on the remote control for 2seconds will open the vehicle’s trunk or hatch.*Throughout this manual, ‘press’ refers to pressing for less than 1 second, ‘press and hold’ refers to pressing formore than 2 seconds.
Using Your Remote Control, continued Turning on the Vehicle’s Headlights (Optional)If this feature is enabled on your system, pressing and holding the LOCK button on the remote control for 3seconds will turn on the vehicle’s headlights for 30 seconds. Activating Optional AUX 1 (Optional)If this feature is enabled on your system, press and release the OPT button on the remote control to activate anoptional feature. This feature can be programmed for a wide range of functions like power window or sunroofautomation, please consult your installing dealer to determine functionality of your system. Activating Optional AUX 2 (Optional)If this feature is enabled on your system, pressing and holding the KEY button on the remote control for 2 secondswill activate an optional feature. This feature can be programmed for a wide range of functions like power windowor sunroof automation, please consult your installing dealer to determine functionality of your system. Activating Optional AUX 3 (Optional)If this feature is enabled on your system, pressing and holding the LOCK button and the Trunk button on the remotecontrol simultaneously for 2 seconds will activate an optional feature. This feature can be programmed for a widerange of functions like power window or sunroof automation, please consult your installing dealer to determinefunctionality of your system. Activating Optional AUX 4 (Optional)If this feature is enabled on your system, pressing and holding the UNLOCK button and the TRUNK button on theremote control simultaneously for 2 seconds will activate an optional feature. This feature can be programmed for awide range of functions like power window or sunroof automation, please consult your installing dealer to determinefunctionality of your system. Using the Progressive Car Finder FeaturePress the LOCK button and the UNLOCK button on the remote control to locate your vehicle. The system willsound 5 times at low volume increasing in volume each of 3 times the button is pressed. Using the Personal Protection Alarm (Panic)Press and hold the LOCK button and the UNLOCK button on the remote control for 2 seconds to activate thepersonal protection alarm. The system will sound for 30 seconds. Pressing any button on the remote control willturn the personal protection alarm off.Using Valet ModeTo engage valet mode:1. Turn the ignition key to the ON position.2. Press and hold the emergency override button.3. The blue dashboard mounted LED will light solid indicating that the system is in valet mode.When valet mode is activated the dash mounted status LED will light solid, and all security functions will bedisabled.To disengage valet mode:1. Turn the ignition key to the ON position.2. Press and release the emergency override button.3. The blue dashboard mounted LED will turn off indicating that the system has exited valet mode.
FCC COMPLIANCEThis device complies with Part 15 of the FCC rules and with RSS-210 of IndustryCanada. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including any interference thatmay cause undesired operation.Warning!Changes or modifications not expressly approved by the party responsible forcompliance could void the user’s authority to operate the equipment.IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.

Navigation menu