Nutek ATJC Transmitter User Manual 128 8840

Nutek Corporation Transmitter 128 8840

User manual

128-88401 of 811213345BUTTON RECEIVERCHANNEL SYSTEM FUNCTIONLock And Arm Alarm, also initiate andterminates *PanicUnlock And Disarm, also initiates andterminates *Panic. Programmable tounlock drivers door and or all doors.Lock and arm/unlock and disarm. Maybe programmed to unlock driver's dooror all doors. Also will initiate andterminate *Panic.Pulsed or switched output to controlRemote Trunk Release or optionaldevice connected to channel 3.When pressed and release two times,will provide pulsed output or activate theRemote Start option when installed.When so equipped, this button can beused to operate an optional deviceconnected to channel 4.When so equipped, this button can beused to operate an optional deviceconnected to channel 5.These transmitters makes use of icons (symbols) to identify the reac-tion your security system/keyless entry/and or remote start system,where applicable, will have when any icon (button) is pressed.These icons are programmed at time of installation to meet the needs ofthe individual and to complement the vehicle that the system is installedin. To replace a transmitter or add transmitters, please follow theprogramming instructions listed on the pages of this manual.Transmitter Programming Guide* Where So EquippedModel SS91
128-88402 of 82Although the most common use of the transmitter buttons are shownon the front page of this guide, any button or button combination can beprogrammed into any receiver channel. Additionally, if all 4 buttons areused and you require access to a 5th channel, you would program acombination of buttons to control the 5th function. i.e... you haveprogrammed lock for arm, unlock for disarm, trunk for trunk release,and OPT1 Sliding Door where applicable, and you've added a win-dow up module that you want independent control of, you would pro-gram unlock and trunk buttons pressed simultaneously into the receiverto control this function independently. Also, if you do not program atransmitter button into channel 2 which is the separate unlock/dis-arm channel, then whatever button is programmed into channel 1will serve as both lock/arm & unlock/disarm.PROGRAMMING TRANSMITTERS:NOTE: It is important to remember that during the programming mode,each individual step must be completed within 15 seconds ofthe previous step. If the 15 second time limit expires betweensteps, the unit will automatically exit the program mode. Thisis indicated by a long chirp from the siren.Non alarm models will flash the parking lights only to confirm thetransmitter code has been learned and stored.NOTE: Because the system may be capable of sounding a siren, thevehicle horn, or both, where the siren chirp is referenced be-low, the siren may chirp, the horn may beep, or both devicesmay sound.TO PROGRAM ADDITIONAL TRANSMITTERS:1) Enter the vehicle, and turn the ignition switch to the on position.2) Press and release the valet push button switch three times.NOTE: Some systems may use a combination push-button LEDswitch, others may use an intergrated push-button LED receiver. Inthese systems the push-button and the dash mounted LED, or thereceiver, push-button,LED are one and the same.3) The LED will flash 1x, and the siren will chirp 1x, indicating that thesystem is ready to accept programming of channel #1 which is arm/lock, disarm/unlock/unlock 2, and panic functions.4) Press and hold the lock or lock/unlock symbol button of the transmit-ter you wish to program for 4 seconds or until a long chirp is heardfrom the siren."Repeat step 4 for each transmitter you wish to program".NOTE: If your transmitter button has the Lock/Unlock icon on onebutton, press and release the valet push button switch 2 timesthen move on to step #8.5) Press and release the valet push button switch one time to advance tochannel 2. The siren will chirp 2 times and the dash mounted LED will
128-88403 of 83Flash 2 times, indicating that the unit is ready to accept programmingfor channel # 2 which is only used for separate lock and unlockbutton transmitters, and is the disarm/unlock/unlock 2 and panic.6) Press and hold the unlock symbol button of the transmitter you wishto program for 4 seconds or until a long chirp is heard from thesiren."Repeat step 6 for each transmitter you wish to program".7) Press and release the valet push button switch one time to ad-vance to channel 3.The siren will chirp 3 times and the dash mountedLED will Flash 3 times, indicating that the unit is ready to acceptprogramming for channel # 3 which is the trunk release/alternateoutput channel of the system.8) Press and hold the trunk/key symbol button of the transmitter youwish to program for 4 seconds or until a long chirp is heard from thesiren."Repeat step 8 for each transmitter you wish to program".9) Press and release the valet push button switch one time to advanceto channel 4 if so equipped. The siren will chirp 4 times and thedash mounted LED will Flash 4 times, indicating that the unit is readyto accept programming for channel # 4, optional device (whereequipped)10) Press and hold the Option button of the transmitter you wish toprogram for 4 seconds or until a long chirp is heard from the siren."Repeat step 10 for each transmitter you wish to program".11) Press and release the valet push button switch one time to ad-vance to channel 5 if so equipped. The siren will chirp 5 times andthe dash mounted LED will Flash 5 times, indicating that the unit isready to accept programming for channel # 5 optional device (whereequipped)12) Press and hold the second Option button of the transmitter youwish to program for 4 seconds or until a long chirp is heard from thesiren."Repeat step 12 for each transmitter you wish to program".13) Within 10 seconds, press and release the valet program switchone time. (Siren emits 6 short chirps indicating channel 6 hasbeen entered)14) Within 10 Seconds, Press and hold the unlock button, (or anyunused button(s)), of the first transmitter you wish to controlChannel 6 output, (Driver Priority 1) until a long chirp is heardfrom the siren. (Repeat this for each transmitter you wish tooperate the Channel 6 output, Driver Priority 1)15) Within 10 seconds, press and release the valet program switchone time. (Siren emits 7 short chirps indicating channel 7 hasbeen entered)
128-88404 of 8416) Within 10 Seconds, Press and hold the unlock button (or anyunused button(s)) of the first transmitter you wish to controlChannel 7 output, (Driver Priority 2) until a long chirp is heardfrom the siren.(Repeat this for each transmitter you wish to operate the Channel 7output, Driver Priority 2)NOTE: Channels 6 and 7 can be used as a separate output tocontrol a function other than driver priority. Simply program-ming any unused transmitter button other than the unlockbutton will allow complete independent control of theseoutputs.ERASING TRANSMITTERS IF THEY HAVE BEEN LOST OR STOLEN:NOTE: Before you begin to erase the lost or stolen transmitter(s), haveall transmitters available that you wish to remain programmed.These will be used during the program process to identifytransmitters that will continue to be used.Enter the transmitter program mode:1. Turn the ignition switch to the “ON” position.2. Within 10 seconds, press and release the valet/program switchthree times. (Siren emits 1 short chirp indicating channel 1 hasbeen entered)3. Within 10 Seconds, press and hold the ARM or ARM/DISARMbutton of the first transmitter you wish to remain stored into thecontrol unit until a single chirp is heard from the siren.(Repeat this for each transmitter you wish to remain stored in the controlunit).The receiver stores up to four transmitters. To be certain all transmitterslots in the receiver are occupied with transmitters you wish to con-tinue to use, and all others are erased, you will have to fill all fourreceiver slots. If in step 3 you identified one transmitter, you will haveto fill the additional 3 slots. If in step 3 you identified two transmitters,you will have to fill the additional two slots, etc...4. Press and hold any unused button or combination of buttons until along chirp is heard from the siren. Release and press the button orbutton combination again and again until all remaining slots are full.NOTE: The button or combination of buttons entered will also controlthe arm or arm/disarm function until additional transmitters areadded. All unwanted transmitters are now deleted.REPRIORITIZING A TRANSMITTER’S PROGRAMMING:To reprogram a receiver channel with a different transmitter buttononce a code has been stored, there will be two options:1. Enter the transmitter program mode of the receiver channel to bereprogrammed. Using any unused button or combination of but-tons, push out the stored code by pressing the unused button untila long chirp is heard, then repeat 3 additional times. After this, you
128-88405 of 85can add any desired unused transmitter button. This action erasesonly the button stored of the transmitter you are programming. Allother codes will remain stored.2. Enter the transmitter program mode. Using any transmitter buttonpress and hold until a long chirp is heard. If a single chirp or multiplechirps, (up to 7 chirps), are heard, the unit is indicating that thetransmitter has already been programmed elsewhere in the re-ceiver. Release the transmitter button and within 5 seconds pressand hold until a long chirp is heard. This action forces the unit toerase all stored codes of that transmitter.The unit then exits the program mode the siren emits the program modeexit chirp pattern. All transmitter buttons for that transmitter must nowbe reprogrammed. Any other transmitter stored in the unit’s memory stillremain operational. If the button is released and not pressed againwithin the 5 second period, no change in programming has been madeto the receiver channel. The programmer can move onto a differentchannel or erase the transmitter codes as described in 1 above.BATTERY REPLACEMENT:The transmitter incorporates a small LED visible through the case whichis used to indicate battery condition. You will notice a decrease intransmitter range as the battery condition deteriorates. Transmit-ter battery replacement is recommended at least every 10 to 12 months,depending upon how frequently the transmitter is used. To replace the battery:1) Remove the 3 small # 0 Phillips head screw from the rear of thecase.2) Remove the rear cover to access the discharged battery payingattention to the proper polarity orientation.3) Carefully remove and properly dispose of the discharged battery.4) Insert the new battery, close the case, then reinstall the 3 small casescrew removed in step 1.5) If you accidently dislodge the circuit board from the transmitter hous-ing, be certain that the rubber membrane is seated properly, and thebuttons are properly exposed from the front view of the case,then insert the circuit board, and return to step #4.SS91P uses CR2032 Coin Cell Type Batteries.SEE ASSOCIATED DIAGRAMS ON FOLLOWING PAGE
128-88406 of 86Remove three #0 philips head screwswhere indicated to gain access to theCR 2032 battery. Carefully removetransmitter back cover.Carefully remove the discharged battery bysliding it out from under the clip in thedirection indicated by the arrow in thediagram below.Properly dispose of the exhausted battery andinsert a new CR2032 taking care to arrange itso that the + is facing up toward the + symbolon the battery clip.This device complies with FCC Rules Part 15 Operation is subject tothe following two conditions:1. This device may not cause harmful interference and2. This device must accept any interference that may be received,including interference that may cause undesired operation.NOTE: The manufacturer is not responsible for any radio or TVinterference caused by unauthorized modifications to thisequipment. Such modifications could void the user’sauthority to operate the equipment.
128-88407 of 871) Name: _______________________________________2)Address: ______________________________________3) City: ________________ State: _____ Zip Code: ________4) Telephone Number: (_____) _______________5) Total Number Of Transmitters Required:Cost Per Transmitter is: $75.00Multiply By Number Of Transmitters X ______6) Enter Total Amount Enclosed _________________(New York State Residents must include the appropriate sales tax)7) Method of Payment:  Mastercard  Visa  Check or Money Order (do not send cash)Make Checks Payable To Audiovox CorporationCreditCard Number: _________________________________Credit Card Expiration Date: ____ / _____ / _____8) Mail this form along with your payment to:ORDER FORM FOR SS 91 TransmitterAudiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y., 11788Attn.: TRANSMITTER DEPARTMENTCredit card purchasers can order additional or replacementtransmitters by phone. Simply dial 1 - 800 - 645 - 4994, andfollow the instructions from the operator interface.Attention: Transmitter Ordering DepartmentImportant: To help us expedite your order, please print all of theinformation legibly and mail this form and your paymentaccording to the instructions below.Indicate the pad number of your transmitter selected from thepads shown above.Note: Transmitter model number found on back of case.
128-88408 of 88128-8840© 2010 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, NY, 11788

Navigation menu